| Age | Commit message (Collapse) | Author |
|---|
|
commit 5603731a15ef9ca317c122cc8c959f1dee1798b4 upstream.
In R-Car Gen2 or later, the maximum number of transfer blocks are
changed from 0xFFFF to 0xFFFFFFFF. Therefore, Block Count Register
should use iowrite32().
If another system (U-boot, Hypervisor OS, etc) uses bit[31:16], this
value will not be cleared. So, SD/MMC card initialization fails.
So, check for the bigger register and use apropriate write. Also, mark
the register as extended on Gen2.
Signed-off-by: Takeshi Saito <takeshi.saito.xv@renesas.com>
[wsa: use max_blk_count in if(), add Gen2, update commit message]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Cc: stable@kernel.org
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
[Ulf: Fixed build error]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5c27ff5db1491a947264d6d4e4cbe43ae6535bae upstream.
I have encountered an interrupt storm during the eMMC chip probing (and
the chip finally didn't get detected). It turned out that U-Boot left
the DMAC interrupts enabled while the Linux driver didn't use those.
The SDHI driver's interrupt handler somehow assumes that, even if an
SDIO interrupt didn't happen, it should return IRQ_HANDLED. I think
that if none of the enabled interrupts happened and got handled, we
should return IRQ_NONE -- that way the kernel IRQ code recoginizes
a spurious interrupt and masks it off pretty quickly...
Fixes: 7729c7a232a9 ("mmc: tmio: Provide separate interrupt handlers")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c9bd505dbd9d3dc80c496f88eafe70affdcf1ba6 upstream.
When using the mmc_spi driver with a card-detect pin, I noticed that the
card was not detected immediately after probe, but only after it was
unplugged and plugged back in (and the CD IRQ fired).
The call tree looks something like this:
mmc_spi_probe
mmc_add_host
mmc_start_host
_mmc_detect_change
mmc_schedule_delayed_work(&host->detect, 0)
mmc_rescan
host->bus_ops->detect(host)
mmc_detect
_mmc_detect_card_removed
host->ops->get_cd(host)
mmc_gpio_get_cd -> -ENOSYS (ctx->cd_gpio not set)
mmc_gpiod_request_cd
ctx->cd_gpio = desc
To fix this issue, call mmc_detect_change after the card-detect GPIO/IRQ
is registered.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 83e418a805d880a8b18add07f94d19b2a5a80307 upstream.
Commit bb364890323cca ("mmc: meson-gx: Free irq in release() callback")
changed the _probe code to use request_threaded_irq() instead of
devm_request_threaded_irq().
Unfortunately this removes a fallback for the interrupt name:
devm_request_threaded_irq() uses the device name as fallback if the
given IRQ name is NULL. request_threaded_irq() has no such fallback,
thus /proc/interrupts shows "(null)" instead.
Explicitly pass the dev_name() so we get the IRQ name shown in
/proc/interrupts again.
While here, also fix the indentation of the request_threaded_irq()
parameter list.
Fixes: bb364890323cca ("mmc: meson-gx: Free irq in release() callback")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit dcf6e2e38a1c7ccbc535de5e1d9b14998847499d upstream.
The kblockd workqueue is created with the WQ_MEM_RECLAIM flag set.
This generates a rescuer thread for that queue that will trigger when
the CPU is under heavy load and collect the uncompleted work.
In the case of mmc, this creates the possibility of a deadlock when
there are multiple partitions on the device as other blk-mq work is
also run on the same queue. For example:
- worker 0 claims the mmc host to work on partition 1
- worker 1 attempts to claim the host for partition 2 but has to wait
for worker 0 to finish
- worker 0 schedules complete_work to release the host
- rescuer thread is triggered after time-out and collects the dangling
work
- rescuer thread attempts to complete the work in order starting with
claim host
- the task to release host is now blocked by a task to claim it and
will never be called
The above results in multiple hung tasks that lead to failures to
mount partitions.
Handling complete_work on a separate workqueue avoids this by keeping
the work completion tasks separate from the other blk-mq work. This
allows the host to be released without getting blocked by other tasks
attempting to claim the host.
Signed-off-by: Zachary Hays <zhays@lexmark.com>
Fixes: 81196976ed94 ("mmc: block: Add blk-mq support")
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d6f11e7d91f2ac85f66194fe3ef8789b49901d64 upstream.
The MMC device tree bindings include properties used to signal various
signalling speed modes. Until now the sunxi driver was accepting them
without any further filtering, while the sunxi device trees were not
actually using them.
Since some of the H5 boards can not run at higher speed modes stably,
we are resorting to declaring the higher speed modes per-board.
Regardless, having boards declare modes and blindly following them,
even without proper support in the driver, is generally a bad thing.
Filter out all unsupported modes from the capabilities mask after
the device tree properties have been parsed.
Cc: <stable@vger.kernel.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 0c901c0566fb4edc2631c3786e5085a037be91f8 ]
Modifty the JZ4740 driver to retrieve card detect and write
protect GPIO pins from GPIO descriptors instead of hard-coded
global numbers. Augment the only board file using this in the
process and cut down on passed in platform data.
Preserve the code setting the caps2 flags for CD and WP
as active low or high since the slot GPIO code currently
ignores the gpiolib polarity inversion semantice and uses
the raw accessors to read the GPIO lines, but set the right
polarity flags in the descriptor table for jz4740.
Cc: Paul Cercueil <paul@crapouillou.net>
Cc: linux-mips@linux-mips.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0e6e7c2ff397e1bbebc882ca3132148aaaef1ddd ]
Always check the wait condition before returning timeout.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Zhoujie Wu <zjwu@marvell.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9f0ea0bda1d06120b053bb0c283f54afec59293d ]
Always check the wait condition before returning timeout.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ea6d027312111c6d96309ad1a684b33cb37e6764 ]
Always check the wait condition before returning timeout.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b0d06f1cb0e2079a3c64fb6e27c19d9a55c723a1 ]
devm_kasprintf() may return NULL on failure of internal allocation thus
the assignments to init.name are not safe if not checked. On error
meson_mx_mmc_register_clks() returns negative values so -ENOMEM in the
(unlikely) failure case of devm_kasprintf() should be fine here.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Fixes: ed80a13bb4c4 ("mmc: meson-mx-sdio: Add a driver for the Amlogic Meson8 and Meson8b SoCs")
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f6000a4eb34e6462bc0dd39809c1bb99f9633269 ]
The bcm2835 mmc host tends to lock up for unknown reason so reset it on
timeout. The upper mmc block layer tries retransimitting with single
blocks which tends to work out after a long wait.
This is better than giving up and leaving the machine broken for no
obvious reason.
Fixes: 660fc733bd74 ("mmc: bcm2835: Add new driver for the sdhost controller.")
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 07d405769afea5718529fc9e341f0b13b3189b6f ]
If the user issues an "mmc extcsd read", the SD controller receives
what it thinks is a SEND_IF_COND command with an unexpected data block.
The resulting operations leave the FSM stuck in READWAIT, a state which
persists until the MMC framework resets the controller, by which point
the root filesystem is likely to have been unmounted.
A less heavyweight solution is to detect the condition and nudge the
FSM by asserting the (self-clearing) FORCE_DATA_MODE bit.
Link: https://github.com/raspberrypi/linux/issues/2728
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 2bd44dadd5bfb4135162322fd0b45a174d4ad5bf upstream.
We need to handle mmc_of_parse() errors during probe.
This finally fixes the wifi regression on Raspberry Pi 3 series.
In error case the wifi chip was permanently in reset because of
the power sequence depending on the deferred probe of the GPIO expander.
Fixes: b580c52d58d9 ("mmc: sdhci-iproc: add IPROC SDHCI driver")
Cc: stable@vger.kernel.org
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3751e008da0df4384031bd66a516c0292f915605 upstream.
to set cmd internal delay, need set PAD_TUNE register but not PAD_CMD_TUNE
register.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Fixes: 1ede5cb88a29 ("mmc: mediatek: Use data tune for CMD line tune")
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8c9620b1cc9b69e82fa8d4081d646d0016b602e7 upstream.
The BCM2835 MMC host driver requests a DMA channel on probe but neglects
to release the channel in the probe error path. The channel may
therefore be leaked, in particular if devm_clk_get() causes probe
deferral. Fix it.
Fixes: 660fc733bd74 ("mmc: bcm2835: Add new driver for the sdhost controller.")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v4.12+
Cc: Frank Pavlic <f.pavlic@kunbus.de>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit bb364890323cca6e43f13e86d190ebf34a7d8cea upstream.
Because the irq was requested through device managed resources API
(devm_request_threaded_irq()) it was freed after meson_mmc_remove()
completion, thus after mmc_free_host() has reclaimed meson_host memory.
As this irq is IRQF_SHARED, while using CONFIG_DEBUG_SHIRQ, its handler
get called by free_irq(). So meson_mmc_irq() was called after the
meson_host memory reclamation and was using invalid memory.
We ended up with the following scenario:
device_release_driver()
meson_mmc_remove()
mmc_free_host() /* Freeing host memory */
...
devres_release_all()
devm_irq_release()
__free_irq()
meson_mmc_irq() /* Uses freed memory */
To avoid this, the irq is released in meson_mmc_remove() and in
mseon_mmc_probe() error path before mmc_free_host() gets called.
Reported-by: Elie Roudninski <xademax@gmail.com>
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f3716b8ae9347797b73896725f192c3a7b0069b5 upstream.
The SPDX license identifier and the boiler plate text are
contradicting. Only the SPDX license identifier is needed. The
other one is removed.
Fixes: 86958dcc5ad7 ("mmc: dw_mmc-bluefield: Add driver extension")
Cc: stable@vger.kernel.org
Reviewed-by: David Woods <dwoods@mellanox.com>
Signed-off-by: Liming Sun <lsun@mellanox.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit ae460c115b7aa50c9a36cf78fced07b27962c9d0 ]
On our AT91SAM9260 board we use the same sdio bus for wifi and for the
sd card slot. This caused the atmel-mci to give the following splat on
the serial console:
------------[ cut here ]------------
WARNING: CPU: 0 PID: 538 at drivers/mmc/host/atmel-mci.c:859 atmci_send_command+0x24/0x44
Modules linked in:
CPU: 0 PID: 538 Comm: mmcqd/0 Not tainted 4.14.76 #14
Hardware name: Atmel AT91SAM9
[<c000fccc>] (unwind_backtrace) from [<c000d3dc>] (show_stack+0x10/0x14)
[<c000d3dc>] (show_stack) from [<c0017644>] (__warn+0xd8/0xf4)
[<c0017644>] (__warn) from [<c0017704>] (warn_slowpath_null+0x1c/0x24)
[<c0017704>] (warn_slowpath_null) from [<c033bb9c>] (atmci_send_command+0x24/0x44)
[<c033bb9c>] (atmci_send_command) from [<c033e984>] (atmci_start_request+0x1f4/0x2dc)
[<c033e984>] (atmci_start_request) from [<c033f3b4>] (atmci_request+0xf0/0x164)
[<c033f3b4>] (atmci_request) from [<c0327108>] (mmc_start_request+0x280/0x2d0)
[<c0327108>] (mmc_start_request) from [<c032800c>] (mmc_start_areq+0x230/0x330)
[<c032800c>] (mmc_start_areq) from [<c03366f8>] (mmc_blk_issue_rw_rq+0xc4/0x310)
[<c03366f8>] (mmc_blk_issue_rw_rq) from [<c03372c4>] (mmc_blk_issue_rq+0x118/0x5ac)
[<c03372c4>] (mmc_blk_issue_rq) from [<c033781c>] (mmc_queue_thread+0xc4/0x118)
[<c033781c>] (mmc_queue_thread) from [<c002daf8>] (kthread+0x100/0x118)
[<c002daf8>] (kthread) from [<c000a580>] (ret_from_fork+0x14/0x34)
---[ end trace 594371ddfa284bd6 ]---
This is:
WARN_ON(host->cmd);
This was fixed on our board by letting atmci_request_end determine what
state we are in. Instead of unconditionally setting it to STATE_IDLE on
STATE_END_REQUEST.
Signed-off-by: Jonas Danielsson <jonas@orbital-systems.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit a89e7bcb18081c611eb6cf50edd440fa4983a71a upstream.
The Clock Data Recovery (CDR) circuit allows to automatically adjust
the RX sampling-point/phase for high frequency cards (SDR104, HS200...).
CDR is automatically enabled during DLL configuration.
However, according to the APQ8016 reference manual, this function
must be disabled during TX and tuning phase in order to prevent any
interferences during tuning challenges and unexpected phase alteration
during TX transfers.
This patch enables/disables CDR according to the current transfer mode.
This fixes sporadic write transfer issues observed with some SDR104 and
HS200 cards.
Inspired by sdhci-msm downstream patch:
https://chromium-review.googlesource.com/c/chromiumos/third_party/kernel/+/432516/
Reported-by: Leonid Segal <leonid.s@variscite.com>
Reported-by: Manabu Igusa <migusa@arrowjapan.com>
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
[georgi: backport to v4.19+]
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0b479790684192ab7024ce6a621f93f6d0a64d92 upstream.
While booting with rootfs on MMC, the following warning is encountered
on OMAP4430:
omap-dma-engine 4a056000.dma-controller: DMA-API: mapping sg segment longer than device claims to support [len=69632] [max=65536]
This is because the DMA engine has a default maximum segment size of 64K
but HSMMC sets:
mmc->max_blk_size = 512; /* Block Length at max can be 1024 */
mmc->max_blk_count = 0xFFFF; /* No. of Blocks is 16 bits */
mmc->max_req_size = mmc->max_blk_size * mmc->max_blk_count;
mmc->max_seg_size = mmc->max_req_size;
which ends up telling the block layer that we support a maximum segment
size of 65535*512, which exceeds the advertised DMA engine capabilities.
Fix this by clamping the maximum segment size to the lower of the
maximum request size and of the DMA engine device used for either DMA
channel.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e3ae3401aa19432ee4943eb0bbc2ec704d07d793 upstream.
Some eMMCs from Micron have been reported to need ~800 ms timeout, while
enabling the CACHE ctrl after running sudden power failure tests. The
needed timeout is greater than what the card specifies as its generic CMD6
timeout, through the EXT_CSD register, hence the problem.
Normally we would introduce a card quirk to extend the timeout for these
specific Micron cards. However, due to the rather complicated debug process
needed to find out the error, let's simply use a minimum timeout of 1600ms,
the double of what has been reported, for all cards when enabling CACHE
ctrl.
Reported-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Reported-by: Andreas Dannenberg <dannenberg@ti.com>
Reported-by: Faiz Abbas <faiz_abbas@ti.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ba9f39a785a9977e72233000711ef1eb48203551 upstream.
In commit 5320226a0512 ("mmc: core: Disable HPI for certain Hynix eMMC
cards"), then intent was to prevent HPI from being used for some eMMC
cards, which didn't properly support it. However, that went too far, as
even BKOPS and CACHE ctrl became prevented. Let's restore those parts and
allow BKOPS and CACHE ctrl even if HPI isn't supported.
Fixes: 5320226a0512 ("mmc: core: Disable HPI for certain Hynix eMMC cards")
Cc: Pratibhasagar V <pratibha@codeaurora.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a0741ba40a009f97c019ae7541dc61c1fdf41efb upstream.
During a re-initialization of the eMMC card, we may fail to re-enable HPI.
In these cases, that isn't properly reflected in the card->ext_csd.hpi_en
bit, as it keeps being set. This may cause following attempts to use HPI,
even if's not enabled. Let's fix this!
Fixes: eb0d8f135b67 ("mmc: core: support HPI send command")
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b704441e38f645dcfba1348ca3cc1ba43d1a9f31 upstream.
We observed some premature timeouts on a virtualization platform, the log
is like this:
case 1:
[159525.255629] mmc1: Internal clock never stabilised.
[159525.255818] mmc1: sdhci: ============ SDHCI REGISTER DUMP ===========
[159525.256049] mmc1: sdhci: Sys addr: 0x00000000 | Version: 0x00001002
...
[159525.257205] mmc1: sdhci: Wake-up: 0x00000000 | Clock: 0x0000fa03
From the clock control register dump, we are pretty sure the clock was
stablized.
case 2:
[ 914.550127] mmc1: Reset 0x2 never completed.
[ 914.550321] mmc1: sdhci: ============ SDHCI REGISTER DUMP ===========
[ 914.550608] mmc1: sdhci: Sys addr: 0x00000010 | Version: 0x00001002
After checking the sdhci code, we found the timeout check actually has a
little window that the CPU can be scheduled out and when it comes back,
the original time set or check is not valid.
Fixes: 5a436cc0af62 ("mmc: sdhci: Optimize delay loops")
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Alek Du <alek.du@intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit db2039fcfd5754d15986340152e4503737f68f8d upstream.
Commit 7d33c3581536 ("mmc: sdhci-omap: Workaround for Errata i802")
disabled DCRC interrupts during tuning. This write to the interrupt
enable register gets overwritten in sdhci_prepare_data() and the
interrupt is not in fact disabled. Fix this by disabling the interrupt
in the host->ier variable.
Fixes: 7d33c3581536 ("mmc: sdhci-omap: Workaround for Errata i802")
Cc: <stable@vger.kernel.org>
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a44f7cb937321d4961bfc8f28912126b06e701c5 upstream.
When sending out CMD23 in the blk preparation, the comment there
rightfully says:
* However, it is not sufficient to just send CMD23,
* and avoid the final CMD12, as on an error condition
* CMD12 (stop) needs to be sent anyway. This, coupled
* with Auto-CMD23 enhancements provided by some
* hosts, means that the complexity of dealing
* with this is best left to the host. If CMD23 is
* supported by card and host, we'll fill sbc in and let
* the host deal with handling it correctly.
Let's do this behaviour for RPMB as well, and not send CMD23
independently. Otherwise IP cores (like Renesas SDHI) may timeout
because of automatic CMD23/CMD12 handling.
Reported-by: Masaharu Hayakawa <masaharu.hayakawa.ry@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Clément Péron <peron.clem@gmail.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e8cde625bfe8a714a856e1366bcbb259d7346095 upstream.
Since v2.6.22 or so there has been reports [1] about OMAP MMC being
broken on OMAP15XX based hardware (OMAP5910 and OMAP310). The breakage
seems to have been caused by commit 46a6730e3ff9 ("mmc-omap: Fix
omap to use MMC_POWER_ON") that changed clock enabling to be done
on MMC_POWER_ON. This can happen multiple times in a row, and on 15XX
the hardware doesn't seem to like it and the MMC just stops responding.
Fix by memorizing the power mode and do the init only when necessary.
Before the patch (on Palm TE):
mmc0: new SD card at address b368
mmcblk0: mmc0:b368 SDC 977 MiB
mmci-omap mmci-omap.0: command timeout (CMD18)
mmci-omap mmci-omap.0: command timeout (CMD13)
mmci-omap mmci-omap.0: command timeout (CMD13)
mmci-omap mmci-omap.0: command timeout (CMD12) [x 6]
mmci-omap mmci-omap.0: command timeout (CMD13) [x 6]
mmcblk0: error -110 requesting status
mmci-omap mmci-omap.0: command timeout (CMD8)
mmci-omap mmci-omap.0: command timeout (CMD18)
mmci-omap mmci-omap.0: command timeout (CMD13)
mmci-omap mmci-omap.0: command timeout (CMD13)
mmci-omap mmci-omap.0: command timeout (CMD12) [x 6]
mmci-omap mmci-omap.0: command timeout (CMD13) [x 6]
mmcblk0: error -110 requesting status
mmcblk0: recovery failed!
print_req_error: I/O error, dev mmcblk0, sector 0
Buffer I/O error on dev mmcblk0, logical block 0, async page read
mmcblk0: unable to read partition table
After the patch:
mmc0: new SD card at address b368
mmcblk0: mmc0:b368 SDC 977 MiB
mmcblk0: p1
The patch is based on a fix and analysis done by Ladislav Michl.
Tested on OMAP15XX/OMAP310 (Palm TE), OMAP1710 (Nokia 770)
and OMAP2420 (Nokia N810).
[1] https://marc.info/?t=123175197000003&r=1&w=2
Fixes: 46a6730e3ff9 ("mmc-omap: Fix omap to use MMC_POWER_ON")
Reported-by: Ladislav Michl <ladis@linux-mips.org>
Reported-by: Andrzej Zaborowski <balrogg@gmail.com>
Tested-by: Ladislav Michl <ladis@linux-mips.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5305ec6a27b2dc7398a689e661a4a2e951026f09 upstream.
GLK firmware can indicate that the tuning value will be restored after
runtime suspend, but not actually do that. Add a workaround that detects
such cases, and lets the driver do re-tuning instead.
Reported-by: Anisse Astier <anisse@astier.eu>
Tested-by: Anisse Astier <anisse@astier.eu>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit cdcefe6bd9df754f528ffc339d3cc143cea4ddf6 upstream.
Problem:
The card detect IRQ does not work with modern BIOS (that want
to use _DSD to provide the card detect GPIO to the driver).
Details:
The mmc core provides the mmc_gpiod_request_cd() API to let host drivers
request the gpio descriptor for the "card detect" pin.
This pin is specified in the ACPI for the SDHC device:
* Either as a resource using _CRS. This is a method used by legacy BIOS.
(The driver needs to tell which resource index).
* Or as a named property ("cd-gpios"/"cd-gpio") in _DSD (which internally
points to an entry in _CRS). This way, the driver can lookup using a
string. This is what modern BIOS prefer to use.
This API finally results in a call to the following code:
struct gpio_desc *acpi_find_gpio(..., const char *con_id,...)
{
...
/* Lookup gpio (using "<con_id>-gpio") in the _DSD */
...
if (!acpi_can_fallback_to_crs(adev, con_id))
return ERR_PTR(-ENOENT);
...
/* Falling back to _CRS is allowed, Lookup gpio in the _CRS */
...
}
Note that this means that if the ACPI has _DSD properties, the kernel
will never use _CRS for the lookup (Because acpi_can_fallback_to_crs()
will always be false for any device hat has _DSD entries).
The SDHCI driver is thus currently broken on a modern BIOS, even if
BIOS provides both _CRS (for index based lookup) and _DSD entries (for
string based lookup). Ironically, none of these will be used for the
lookup currently because:
* Since the con_id is NULL, acpi_find_gpio() does not find a matching
entry in DSDT. (The _DSDT entry has the property name = "cd-gpios")
* Because ACPI contains DSDT entries, thus acpi_can_fallback_to_crs()
returns false (because device properties have been populated from
_DSD), thus the _CRS is never used for the lookup.
Fix:
Try "cd" for lookup in the _DSD before falling back to using NULL so
as to try looking up in the _CRS.
I've tested this patch successfully with both Legacy BIOS (that
provide only _CRS method) as well as modern BIOS (that provide both
_CRS and _DSD). Also the use of "cd" appears to be fairly consistent
across other users of this API (other MMC host controller drivers).
Link: https://lkml.org/lkml/2018/9/25/1113
Signed-off-by: Rajat Jain <rajatja@google.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Fixes: f10e4bf6632b ("gpio: acpi: Even more tighten up ACPI GPIO lookups")
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit c7eabbee3de99347105faa7fd925a500ccf43baf ]
The device specific resource can be free in free_slot after
removing host controller.
Signed-off-by: Wang Dongsheng <dongsheng.wang@hxt-semitech.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 5169894982bb67486d93cc1e10151712bb86bcb6 ]
This device reports SDHCI_CLOCK_INT_STABLE even though it's not
ready to take SDHCI_CLOCK_CARD_EN. The symptom is that reading
SDHCI_CLOCK_CONTROL after enabling the clock shows absence of the
bit from the register (e.g. expecting 0x0000fa07 = 0x0000fa03 |
SDHCI_CLOCK_CARD_EN but only observed the first operand).
mmc1: Timeout waiting for hardware cmd interrupt.
mmc1: sdhci: ============ SDHCI REGISTER DUMP ===========
mmc1: sdhci: Sys addr: 0x00000000 | Version: 0x00000603
mmc1: sdhci: Blk size: 0x00000000 | Blk cnt: 0x00000000
mmc1: sdhci: Argument: 0x00000000 | Trn mode: 0x00000000
mmc1: sdhci: Present: 0x01ff0001 | Host ctl: 0x00000001
mmc1: sdhci: Power: 0x0000000f | Blk gap: 0x00000000
mmc1: sdhci: Wake-up: 0x00000000 | Clock: 0x0000fa03
mmc1: sdhci: Timeout: 0x00000000 | Int stat: 0x00000000
mmc1: sdhci: Int enab: 0x00ff0083 | Sig enab: 0x00ff0083
mmc1: sdhci: AC12 err: 0x00000000 | Slot int: 0x00000000
mmc1: sdhci: Caps: 0x25fcc8bf | Caps_1: 0x00002077
mmc1: sdhci: Cmd: 0x00000000 | Max curr: 0x005800c8
mmc1: sdhci: Resp[0]: 0x00000000 | Resp[1]: 0x00000000
mmc1: sdhci: Resp[2]: 0x00000000 | Resp[3]: 0x00000000
mmc1: sdhci: Host ctl2: 0x00000008
mmc1: sdhci: ADMA Err: 0x00000000 | ADMA Ptr: 0x00000000
mmc1: sdhci: ============================================
The problem happens during wakeup from S3. Adding a delay quirk
after power up reliably fixes the problem.
Signed-off-by: Yu Zhao <yuzhao@google.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
On some SD cards over SPI, reading with the multiblock read command the last
sector will leave the card in a bad state.
Remove last sectors from the multiblock reading cmd.
Signed-off-by: Chris Boot <bootc@bootc.net>
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Cc: stable@vger.kernel.org # v4.10+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The debounce value passed to mmc_gpiod_request_cd() function is in
microseconds, but msecs_to_jiffies() requires the value to be in
miliseconds to properly calculate the delay, so adjust the value stored
in cd_debounce_delay_ms context entry.
Fixes: 1d71926bbd59 ("mmc: core: Fix debounce time to use microseconds")
Fixes: bfd694d5e21c ("mmc: core: Add tunable delay before detecting card
after card is inserted")
Cc: stable@vger.kernel.org # v4.18+
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The debounce value in device tree is in milliseconds but needs to be in
microseconds for mmc_gpiod_request_cd().
Fixes: bfd694d5e21c ("mmc: core: Add tunable delay before detecting card
after card is inserted")
Cc: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Cc: stable@vger.kernel.org # v4.18+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Fixes: 26eb2607fa28 ("mmc: renesas_sdhi: add eMMC HS400 mode support")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Use the new of_get_compatible_child() helper to lookup the slot child
node instead of using of_find_compatible_node(), which searches the
entire tree from a given start node and thus can return an unrelated
(i.e. non-child) node.
This also addresses a potential use-after-free (e.g. after probe
deferral) as the tree-wide helper drops a reference to its first
argument (i.e. the node of the device being probed).
While at it, also fix up the related slot-node reference leak.
Fixes: ed80a13bb4c4 ("mmc: meson-mx-sdio: Add a driver for the Amlogic Meson8 and Meson8b SoCs")
Cc: stable <stable@vger.kernel.org> # 4.15
Cc: Carlo Caione <carlo@endlessm.com>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
after unbinding mmc I get things like this:
[ 185.294067] mmc1: card 0001 removed
[ 185.305206] omap_hsmmc 480b4000.mmc: wake IRQ with no resume: -13
The wakeirq stays in /proc-interrupts
rebinding shows this:
[ 289.795959] genirq: Flags mismatch irq 112. 0000200a (480b4000.mmc:wakeup) vs. 0000200a (480b4000.mmc:wakeup)
[ 289.808959] omap_hsmmc 480b4000.mmc: Unable to request wake IRQ
[ 289.815338] omap_hsmmc 480b4000.mmc: no SDIO IRQ support, falling back to polling
That bug seems to be introduced by switching from devm_request_irq()
to generic wakeirq handling.
So let us cleanup at removal.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Fixes: 5b83b2234be6 ("mmc: omap_hsmmc: Change wake-up interrupt to use generic wakeirq")
Cc: stable@vger.kernel.org # v4.2+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
I have encountered an interrupt storm during the eMMC chip probing (and
the chip finally didn't get detected). It turned out that U-Boot left
the SDHI DMA interrupts enabled while the Linux driver didn't use those.
Masking those interrupts in renesas_sdhi_internal_dmac_request_dma() gets
rid of both issues...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Fixes: 2a68ea7896e3 ("mmc: renesas-sdhi: add support for R-Car Gen3 SDHI DMAC")
Cc: stable@vger.kernel.org # v4.14+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The DM_CM_RST register actually has bits 0-31 defaulting to 1s and bits
32-63 defaulting to 0s -- fix off-by-one in #define RST_RESERVED_BITS.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Fixes: 2a68ea7896e3 ("mmc: renesas-sdhi: add support for R-Car Gen3 SDHI DMAC")
Cc: stable@vger.kernel.org # v4.14+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The mmc block driver does not support parallel dispatch of requests. In
normal circumstances, all requests are anyway funneled through a single
work item, so parallel dispatch never happens. However it can happen if
there is no elevator.
Fix that by detecting if a dispatch is in progress and returning busy
(BLK_STS_RESOURCE) in that case
Fixes: 81196976ed94 ("mmc: block: Add blk-mq support")
Cc: stable@vger.kernel.org # v4.16+
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The conversion to sg_copy_{from,to}_buffer has been done in the wrong
way. sg_copy_to_buffer is a copy from an SG list to a linear buffer so
it can't replace memcpy(dest, host->virt_base, data->sg->length) where
dest is the virtual address of the SG. Same for sg_copy_from_buffer
but in the opposite way.
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Suggested-by: Douglas Gilbert <dgilbert@interlog.com>
Fixes: 53d7e098ba08 ("mmc: android-goldfish: use sg_copy_{from,to}_buffer")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The conversion to sg_copy_{from,to}_buffer has been done in the wrong
way. sg_copy_to_buffer is a copy from an SG list to a linear buffer so
it can't replace memcpy(buf + offset, &value, remaining) where buf is
the virtual address of the SG. Same for sg_copy_to_buffer but in the
opposite way.
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Suggested-by: Douglas Gilbert <dgilbert@interlog.com>
Fixes: 5b4277814e3f ("mmc: atmel-mci: use sg_copy_{from,to}_buffer")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
mmc_select_hs400es() calls mmc_select_bus_width() which will continue
to set 4bit transfer mode if fail to set 8bit mode. The bus width
should not be set to 4bit in HS400es.
When fail to set 8bit mode, need return error directly for HS400es.
Signed-off-by: Hongjie Fang <hongjiefang@asrmicro.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Pass TMIO_MASK_CMD to tmio_mmc_enable_mmc_irqs() directly,
and remove the variable, irq_mask.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
When tuning each tap is issued CMD19 twice and the result of both runs
recorded in host->taps. If the result is different between the two runs
the wrong sampling clock position was selected. Fix this by merging the
two runs and only keep the result for each tap if it was good in both
sets.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
If the return value of mmc_send_tuning() is error other than -EILSEQ,
the tuning fails and process goes out of for_loop. The correct
processing is to judge their TAP as not good (NG) and continue.
Signed-off-by: Masaharu Hayakawa <masaharu.hayakawa.ry@renesas.com>
[Niklas: update commit message]
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Recent Linux versions refuse to print actual virtual kernel addresses,
to not give a hint about the location of the kernel in a randomized virtual
address space. This affects the output of the sunxi MMC controller
driver, which now produces the rather uninformative line:
[ 1.482660] sunxi-mmc 1c0f000.mmc: base:0x(____ptrval____) irq:8
Since the virtual base address is not really interesting in the first
place, let's just drop this value. The same applies to Linux' notion of
the interrupt number, which is independent from the GIC SPI number.
We have the physical address as part of the DT node name, which is way
more useful for debugging purposes.
To keep a success message in the driver, we make this purpose explicit
with the word "initialized", plus print some information that is not too
obvious and that we learned while probing the device:
the maximum request size and whether it uses the new timing mode.
So the output turns into:
[ 1.750626] sunxi-mmc 1c0f000.mmc: initialized, max. request size: 16384 KB, uses new timings mode
[ 1.786699] sunxi-mmc 1c11000.mmc: initialized, max. request size: 2048 KB
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Some Allwinner boards feature an on-board eMMC with fixed 3.3V voltage
(e.g. Banana Pi M2+), and in this case both the eMMC and the SoC are
capable of doing 3.3V DDR transmission.
Add capability of 3.3V DDR when DDR is available (extra clock or new
timing).
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
As a first step to improve the variant specific code for mmci, add a
->dma_setup() callback to the struct mmci_host_ops.
To show its use, let's deploy the callback for the qcom dml, which involves
also to the assign the mmci_host_ops pointer from the variant ->init()
callback.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Ludovic Barre <ludovic.barre@st.com>
|
Takeshi Saito
Sergei Shtylyov
Jonathan Neuschäfer
Martin Blumenstingl
Zachary Hays
Chen-Yu Tsai
Linus Walleij
Adrian Hunter
Nicholas Mc Guire
Michal Suchanek
Phil Elwell
Stefan Wahren
Chaotian Jing
Lukas Wunner
Remi Pommarel
Liming Sun
Jonas Danielsson
Loic Poulain
Russell King
Ulf Hansson
Alek Du
Faiz Abbas
Wolfram Sang
Aaro Koskinen
Rajat Jain
Wang Dongsheng
Yu Zhao
Chris Boot
Marek Szyprowski
Tony Lindgren
Johan Hovold
Andreas Kemnade
Ludovic Desroches
Hongjie Fang
Masahiro Yamada
Niklas Söderlund
Masaharu Hayakawa
Andre Przywara
Icenowy Zheng