summaryrefslogtreecommitdiffstats
path: root/drivers/mmc
AgeCommit message (Collapse)Author
2021-05-22mmc: core: Set read only for SD cards with permanent write protect bitSeunghui Lee
commit 917a5336f2c27928be270226ab374ed0cbf3805d upstream. Some of SD cards sets permanent write protection bit in their CSD register, due to lifespan or internal problem. To avoid unnecessary I/O write operations, let's parse the bits in the CSD during initialization and mark the card as read only for this case. Signed-off-by: Seunghui Lee <sh043.lee@samsung.com> Link: https://lore.kernel.org/r/20210222083156.19158-1-sh043.lee@samsung.com Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-05-22mmc: core: Do a power cycle when the CMD11 failsDooHyun Hwang
commit 147186f531ae49c18b7a9091a2c40e83b3d95649 upstream. A CMD11 is sent to the SD/SDIO card to start the voltage switch procedure into 1.8V I/O. According to the SD spec a power cycle is needed of the card, if it turns out that the CMD11 fails. Let's fix this, to allow a retry of the initialization without the voltage switch, to succeed. Note that, whether it makes sense to also retry with the voltage switch after the power cycle is a bit more difficult to know. At this point, we treat it like the CMD11 isn't supported and therefore we skip it when retrying. Signed-off-by: DooHyun Hwang <dh0421.hwang@samsung.com> Link: https://lore.kernel.org/r/20210210045936.7809-1-dh0421.hwang@samsung.com Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-05-22mmc: block: Issue a cache flush only when it's enabledAvri Altman
commit 97fce126e279690105ee15be652b465fd96f9997 upstream. In command queueing mode, the cache isn't flushed via the mmc_flush_cache() function, but instead by issuing a CMDQ_TASK_MGMT (CMD48) with a FLUSH_CACHE opcode. In this path, we need to check if cache has been enabled, before deciding to flush the cache, along the lines of what's being done in mmc_flush_cache(). To fix this problem, let's add a new bus ops callback ->cache_enabled() and implement it for the mmc bus type. In this way, the mmc block device driver can call it to know whether cache flushing should be done. Fixes: 1e8e55b67030 (mmc: block: Add CQE support) Cc: stable@vger.kernel.org Reported-by: Brendan Peter <bpeter@lytx.com> Signed-off-by: Avri Altman <avri.altman@wdc.com> Tested-by: Brendan Peter <bpeter@lytx.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Link: https://lore.kernel.org/r/20210425060207.2591-2-avri.altman@wdc.com Link: https://lore.kernel.org/r/20210425060207.2591-3-avri.altman@wdc.com [Ulf: Squashed the two patches and made some minor updates] Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-05-22mmc: block: Update ext_csd.cache_ctrl if it was writtenAvri Altman
commit aea0440ad023ab0662299326f941214b0d7480bd upstream. The cache function can be turned ON and OFF by writing to the CACHE_CTRL byte (EXT_CSD byte [33]). However, card->ext_csd.cache_ctrl is only set on init if cache size > 0. Fix that by explicitly setting ext_csd.cache_ctrl on ext-csd write. Signed-off-by: Avri Altman <avri.altman@wdc.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20210420134641.57343-3-avri.altman@wdc.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-05-22mmc: sdhci-pci: Fix initialization of some SD cards for Intel BYT-based ↵Adrian Hunter
controllers commit 2970134b927834e9249659a70aac48e62dff804a upstream. Bus power may control card power, but the full reset done by SDHCI at initialization still may not reset the power, whereas a direct write to SDHCI_POWER_CONTROL can. That might be needed to initialize correctly, if the card was left powered on previously. Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20210331081752.23621-1-adrian.hunter@intel.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-03-17mmc: cqhci: Fix random crash when remove mmc module/cardFrank Li
commit f06391c45e83f9a731045deb23df7cc3814fd795 upstream. [ 6684.493350] Unable to handle kernel paging request at virtual address ffff800011c5b0f0 [ 6684.498531] mmc0: card 0001 removed [ 6684.501556] Mem abort info: [ 6684.509681] ESR = 0x96000047 [ 6684.512786] EC = 0x25: DABT (current EL), IL = 32 bits [ 6684.518394] SET = 0, FnV = 0 [ 6684.521707] EA = 0, S1PTW = 0 [ 6684.524998] Data abort info: [ 6684.528236] ISV = 0, ISS = 0x00000047 [ 6684.532986] CM = 0, WnR = 1 [ 6684.536129] swapper pgtable: 4k pages, 48-bit VAs, pgdp=0000000081b22000 [ 6684.543923] [ffff800011c5b0f0] pgd=00000000bffff003, p4d=00000000bffff003, pud=00000000bfffe003, pmd=00000000900e1003, pte=0000000000000000 [ 6684.557915] Internal error: Oops: 96000047 [#1] PREEMPT SMP [ 6684.564240] Modules linked in: sdhci_esdhc_imx(-) sdhci_pltfm sdhci cqhci mmc_block mmc_core fsl_jr_uio caam_jr caamkeyblob_desc caamhash_desc caamalg_desc crypto_engine rng_core authenc libdes crct10dif_ce flexcan can_dev caam error [last unloaded: mmc_core] [ 6684.587281] CPU: 0 PID: 79138 Comm: kworker/0:3H Not tainted 5.10.9-01410-g3ba33182767b-dirty #10 [ 6684.596160] Hardware name: Freescale i.MX8DXL EVK (DT) [ 6684.601320] Workqueue: kblockd blk_mq_run_work_fn [ 6684.606094] pstate: 40000005 (nZcv daif -PAN -UAO -TCO BTYPE=--) [ 6684.612286] pc : cqhci_request+0x148/0x4e8 [cqhci] ^GMessage from syslogd@ at Thu Jan 1 01:51:24 1970 ...[ 6684.617085] lr : cqhci_request+0x314/0x4e8 [cqhci] [ 6684.626734] sp : ffff80001243b9f0 [ 6684.630049] x29: ffff80001243b9f0 x28: ffff00002c3dd000 [ 6684.635367] x27: 0000000000000001 x26: 0000000000000001 [ 6684.640690] x25: ffff00002c451000 x24: 000000000000000f [ 6684.646007] x23: ffff000017e71c80 x22: ffff00002c451000 [ 6684.651326] x21: ffff00002c0f3550 x20: ffff00002c0f3550 [ 6684.656651] x19: ffff000017d46880 x18: ffff00002cea1500 [ 6684.661977] x17: 0000000000000000 x16: 0000000000000000 [ 6684.667294] x15: 000001ee628e3ed1 x14: 0000000000000278 [ 6684.672610] x13: 0000000000000001 x12: 0000000000000001 [ 6684.677927] x11: 0000000000000000 x10: 0000000000000000 [ 6684.683243] x9 : 000000000000002b x8 : 0000000000001000 [ 6684.688560] x7 : 0000000000000010 x6 : ffff00002c0f3678 [ 6684.693886] x5 : 000000000000000f x4 : ffff800011c5b000 [ 6684.699211] x3 : 000000000002d988 x2 : 0000000000000008 [ 6684.704537] x1 : 00000000000000f0 x0 : 0002d9880008102f [ 6684.709854] Call trace: [ 6684.712313] cqhci_request+0x148/0x4e8 [cqhci] [ 6684.716803] mmc_cqe_start_req+0x58/0x68 [mmc_core] [ 6684.721698] mmc_blk_mq_issue_rq+0x460/0x810 [mmc_block] [ 6684.727018] mmc_mq_queue_rq+0x118/0x2b0 [mmc_block] The problem occurs when cqhci_request() get called after cqhci_disable() as it leads to access of allocated memory that has already been freed. Let's fix the problem by calling cqhci_disable() a bit later in the remove path. Signed-off-by: Frank Li <Frank.Li@nxp.com> Diagnosed-by: Adrian Hunter <adrian.hunter@intel.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Link: https://lore.kernel.org/r/20210303174248.542175-1-Frank.Li@nxp.com Fixes: f690f4409ddd ("mmc: mmc: Enable CQE's") Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-03-17mmc: core: Fix partition switch time for eMMCAdrian Hunter
commit 66fbacccbab91e6e55d9c8f1fc0910a8eb6c81f7 upstream. Avoid the following warning by always defining partition switch time: [ 3.209874] mmc1: unspecified timeout for CMD6 - use generic [ 3.222780] ------------[ cut here ]------------ [ 3.233363] WARNING: CPU: 1 PID: 111 at drivers/mmc/core/mmc_ops.c:575 __mmc_switch+0x200/0x204 Reported-by: Paul Fertser <fercerpav@gmail.com> Fixes: 1c447116d017 ("mmc: mmc: Fix partition switch timeout for some eMMCs") Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Link: https://lore.kernel.org/r/168bbfd6-0c5b-5ace-ab41-402e7937c46e@intel.com Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-03-17mmc: mediatek: fix race condition between msdc_request_timeout and irqChaotian Jing
[ Upstream commit 0354ca6edd464a2cf332f390581977b8699ed081 ] when get request SW timeout, if CMD/DAT xfer done irq coming right now, then there is race between the msdc_request_timeout work and irq handler, and the host->cmd and host->data may set to NULL in irq handler. also, current flow ensure that only one path can go to msdc_request_done(), so no need check the return value of cancel_delayed_work(). Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com> Link: https://lore.kernel.org/r/20201218071611.12276-1-chaotian.jing@mediatek.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-03-17mmc: mxs-mmc: Fix a resource leak in an error handling path in 'mxs_mmc_probe()'Christophe JAILLET
[ Upstream commit 0bb7e560f821c7770973a94e346654c4bdccd42c ] If 'mmc_of_parse()' fails, we must undo the previous 'dma_request_chan()' call. Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Link: https://lore.kernel.org/r/20201208203527.49262-1-christophe.jaillet@wanadoo.fr Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-03-11mmc: sdhci-of-dwcmshc: set SDHCI_QUIRK2_PRESET_VALUE_BROKENJisheng Zhang
[ Upstream commit 5f7dfda4f2cec580c135fd81d96a05006651c128 ] The SDHCI_PRESET_FOR_* registers are not set(all read as zeros), so set the quirk. Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com> Link: https://lore.kernel.org/r/20201210165510.76b917e5@xhacker.debian Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-03-11block: genhd: add 'groups' argument to device_add_diskHannes Reinecke
commit fef912bf860e8e7e48a2bfb978a356bba743a8b7 upstream. Update device_add_disk() to take an 'groups' argument so that individual drivers can register a device with additional sysfs attributes. This avoids race condition the driver would otherwise have if these groups were to be created with sysfs_add_groups(). Signed-off-by: Martin Wilck <martin.wilck@suse.com> Signed-off-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Jeffle Xu <jefflexu@linux.alibaba.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-03-04mmc: sdhci-esdhc-imx: fix kernel panic when remove moduleFrank Li
commit a56f44138a2c57047f1ea94ea121af31c595132b upstream. In sdhci_esdhc_imx_remove() the SDHCI_INT_STATUS in read. Under some circumstances, this may be done while the device is runtime suspended, triggering the below splat. Fix the problem by adding a pm_runtime_get_sync(), before reading the register, which will turn on clocks etc making the device accessible again. [ 1811.323148] mmc1: card aaaa removed [ 1811.347483] Internal error: synchronous external abort: 96000210 [#1] PREEMPT SMP [ 1811.354988] Modules linked in: sdhci_esdhc_imx(-) sdhci_pltfm sdhci cqhci mmc_block mmc_core [last unloaded: mmc_core] [ 1811.365726] CPU: 0 PID: 3464 Comm: rmmod Not tainted 5.10.1-sd-99871-g53835a2e8186 #5 [ 1811.373559] Hardware name: Freescale i.MX8DXL EVK (DT) [ 1811.378705] pstate: 60000005 (nZCv daif -PAN -UAO -TCO BTYPE=--) [ 1811.384723] pc : sdhci_esdhc_imx_remove+0x28/0x15c [sdhci_esdhc_imx] [ 1811.391090] lr : platform_drv_remove+0x2c/0x50 [ 1811.395536] sp : ffff800012c7bcb0 [ 1811.398855] x29: ffff800012c7bcb0 x28: ffff00002c72b900 [ 1811.404181] x27: 0000000000000000 x26: 0000000000000000 [ 1811.409497] x25: 0000000000000000 x24: 0000000000000000 [ 1811.414814] x23: ffff0000042b3890 x22: ffff800009127120 [ 1811.420131] x21: ffff00002c4c9580 x20: ffff0000042d0810 [ 1811.425456] x19: ffff0000042d0800 x18: 0000000000000020 [ 1811.430773] x17: 0000000000000000 x16: 0000000000000000 [ 1811.436089] x15: 0000000000000004 x14: ffff000004019c10 [ 1811.441406] x13: 0000000000000000 x12: 0000000000000020 [ 1811.446723] x11: 0101010101010101 x10: 7f7f7f7f7f7f7f7f [ 1811.452040] x9 : fefefeff6364626d x8 : 7f7f7f7f7f7f7f7f [ 1811.457356] x7 : 78725e6473607372 x6 : 0000000080808080 [ 1811.462673] x5 : 0000000000000000 x4 : 0000000000000000 [ 1811.467990] x3 : ffff800011ac1cb0 x2 : 0000000000000000 [ 1811.473307] x1 : ffff8000091214d4 x0 : ffff8000133a0030 [ 1811.478624] Call trace: [ 1811.481081] sdhci_esdhc_imx_remove+0x28/0x15c [sdhci_esdhc_imx] [ 1811.487098] platform_drv_remove+0x2c/0x50 [ 1811.491198] __device_release_driver+0x188/0x230 [ 1811.495818] driver_detach+0xc0/0x14c [ 1811.499487] bus_remove_driver+0x5c/0xb0 [ 1811.503413] driver_unregister+0x30/0x60 [ 1811.507341] platform_driver_unregister+0x14/0x20 [ 1811.512048] sdhci_esdhc_imx_driver_exit+0x1c/0x3a8 [sdhci_esdhc_imx] [ 1811.518495] __arm64_sys_delete_module+0x19c/0x230 [ 1811.523291] el0_svc_common.constprop.0+0x78/0x1a0 [ 1811.528086] do_el0_svc+0x24/0x90 [ 1811.531405] el0_svc+0x14/0x20 [ 1811.534461] el0_sync_handler+0x1a4/0x1b0 [ 1811.538474] el0_sync+0x174/0x180 [ 1811.541801] Code: a9025bf5 f9403e95 f9400ea0 9100c000 (b9400000) [ 1811.547902] ---[ end trace 3fb1a3bd48ff7be5 ]--- Signed-off-by: Frank Li <Frank.Li@nxp.com> Cc: stable@vger.kernel.org # v4.0+ Link: https://lore.kernel.org/r/20210210181933.29263-1-Frank.Li@nxp.com [Ulf: Clarified the commit message a bit] Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-03-04mmc: renesas_sdhi_internal_dmac: Fix DMA buffer alignment from 8 to 128-bytesTakeshi Saito
[ Upstream commit d7aefb2887601cf1fc3f86f55d43b2c9aece5e8f ] According to the latest datasheet, the internal DMAC buffer alignment R-Car Gen3 SDHI HW should be 128-bytes. So, fix it. Signed-off-by: Takeshi Saito <takeshi.saito.xv@renesas.com> [shimoda: revise commit description, rebase] Fixes: 2a68ea7896e3 ("mmc: renesas-sdhi: add support for R-Car Gen3 SDHI DMAC") Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Link: https://lore.kernel.org/r/1608114572-1892-2-git-send-email-yoshihiro.shimoda.uh@renesas.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-03-04mmc: usdhi6rol0: Fix a resource leak in the error handling path of the probeChristophe JAILLET
[ Upstream commit 6052b3c370fb82dec28bcfff6d7ec0da84ac087a ] A call to 'ausdhi6_dma_release()' to undo a previous call to 'usdhi6_dma_request()' is missing in the error handling path of the probe function. It is already present in the remove function. Fixes: 75fa9ea6e3c0 ("mmc: add a driver for the Renesas usdhi6rol0 SD/SDIO host controller") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Link: https://lore.kernel.org/r/20201217210922.165340-1-christophe.jaillet@wanadoo.fr Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-02-10mmc: core: Limit retries when analyse of SDIO tuples failsFengnan Chang
commit f92e04f764b86e55e522988e6f4b6082d19a2721 upstream. When analysing tuples fails we may loop indefinitely to retry. Let's avoid this by using a 10s timeout and bail if not completed earlier. Signed-off-by: Fengnan Chang <fengnanchang@gmail.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20210123033230.36442-1-fengnanchang@gmail.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-01-27mmc: sdhci-xenon: fix 1.8v regulator stabilizationAlex Leibovich
commit 1a3ed0dc3594d99ff341ec63865a40519ea24b8d upstream. Automatic Clock Gating is a feature used for the power consumption optimisation. It turned out that during early init phase it may prevent the stable voltage switch to 1.8V - due to that on some platforms an endless printout in dmesg can be observed: "mmc1: 1.8V regulator output did not became stable" Fix the problem by disabling the ACG at very beginning of the sdhci_init and let that be enabled later. Fixes: 3a3748dba881 ("mmc: sdhci-xenon: Add Marvell Xenon SDHC core functionality") Signed-off-by: Alex Leibovich <alexl@marvell.com> Signed-off-by: Marcin Wojtas <mw@semihalf.com> Cc: stable@vger.kernel.org Acked-by: Adrian Hunter <adrian.hunter@intel.com> Link: https://lore.kernel.org/r/20201211141656.24915-1-mw@semihalf.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-01-27mmc: core: don't initialize block size from ext_csd if not presentPeter Collingbourne
commit b503087445ce7e45fabdee87ca9e460d5b5b5168 upstream. If extended CSD was not available, the eMMC driver would incorrectly set the block size to 0, as the data_sector_size field of ext_csd was never initialized. This issue was exposed by commit 817046ecddbc ("block: Align max_hw_sectors to logical blocksize") which caused max_sectors and max_hw_sectors to be set to 0 after setting the block size to 0, resulting in a kernel panic in bio_split when attempting to read from the device. Fix it by only reading the block size from ext_csd if it is available. Fixes: a5075eb94837 ("mmc: block: Allow disabling 512B sector size emulation") Signed-off-by: Peter Collingbourne <pcc@google.com> Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com> Link: https://linux-review.googlesource.com/id/If244d178da4d86b52034459438fec295b02d6e60 Acked-by: Adrian Hunter <adrian.hunter@intel.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20210114201405.2934886-1-pcc@google.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-12-30mmc: block: Fixup condition for CMD13 polling for RPMB requestsBean Huo
commit 6246d7c9d15aaff0bc3863f67900c6a6e6be921b upstream. The CMD13 polling is needed for commands with R1B responses. In commit a0d4c7eb71dd ("mmc: block: Add CMD13 polling for MMC IOCTLS with R1B response"), the intent was to introduce this for requests targeted to the RPMB partition. However, the condition to trigger the polling loop became wrong, leading to unnecessary polling. Let's fix the condition to avoid this. Fixes: a0d4c7eb71dd ("mmc: block: Add CMD13 polling for MMC IOCTLS with R1B response") Cc: stable@vger.kernel.org Reported-by: Zhan Liu <zliua@micron.com> Signed-off-by: Zhan Liu <zliua@micron.com> Signed-off-by: Bean Huo <beanhuo@micron.com> Link: https://lore.kernel.org/r/20201202202320.22165-1-huobean@gmail.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-11-18mmc: renesas_sdhi_core: Add missing tmio_mmc_host_free() at removeYoshihiro Shimoda
commit e8973201d9b281375b5a8c66093de5679423021a upstream. The commit 94b110aff867 ("mmc: tmio: add tmio_mmc_host_alloc/free()") added tmio_mmc_host_free(), but missed the function calling in the sh_mobile_sdhi_remove() at that time. So, fix it. Otherwise, we cannot rebind the sdhi/mmc devices when we use aliases of mmc. Fixes: 94b110aff867 ("mmc: tmio: add tmio_mmc_host_alloc/free()") Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/1604654730-29914-1-git-send-email-yoshihiro.shimoda.uh@renesas.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-11-05mmc: sdhci-acpi: AMDI0040: Set SDHCI_QUIRK2_PRESET_VALUE_BROKENRaul E Rangel
commit f23cc3ba491af77395cea3f9d51204398729f26b upstream. This change fixes HS400 tuning for devices with invalid presets. SDHCI presets are not currently used for eMMC HS/HS200/HS400, but are used for DDR52. The HS400 retuning sequence is: HS400->DDR52->HS->HS200->Perform Tuning->HS->HS400 This means that when HS400 tuning happens, we transition through DDR52 for a very brief period. This causes presets to be enabled unintentionally and stay enabled when transitioning back to HS200 or HS400. Some firmware has invalid presets, so we end up with driver strengths that can cause I/O problems. Fixes: 34597a3f60b1 ("mmc: sdhci-acpi: Add support for ACPI HID of AMD Controller with HS400") Signed-off-by: Raul E Rangel <rrangel@chromium.org> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20200928154718.1.Icc21d4b2f354e83e26e57e270dc952f5fe0b0a40@changeid Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-11-05mmc: via-sdmmc: Fix data race bugMadhuparna Bhowmik
[ Upstream commit 87d7ad089b318b4f319bf57f1daa64eb6d1d10ad ] via_save_pcictrlreg() should be called with host->lock held as it writes to pm_pcictrl_reg, otherwise there can be a race condition between via_sd_suspend() and via_sdc_card_detect(). The same pattern is used in the function via_reset_pcictrl() as well, where via_save_pcictrlreg() is called with host->lock held. Found by Linux Driver Verification project (linuxtesting.org). Signed-off-by: Madhuparna Bhowmik <madhuparnabhowmik10@gmail.com> Link: https://lore.kernel.org/r/20200822061528.7035-1-madhuparnabhowmik10@gmail.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2020-10-30mmc: sdio: Check for CISTPL_VERS_1 buffer sizePali Rohár
[ Upstream commit 8ebe2607965d3e2dc02029e8c7dd35fbe508ffd0 ] Before parsing CISTPL_VERS_1 structure check that its size is at least two bytes to prevent buffer overflow. Signed-off-by: Pali Rohár <pali@kernel.org> Link: https://lore.kernel.org/r/20200727133837.19086-2-pali@kernel.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2020-10-14mmc: core: don't set limits.discard_granularity as 0Coly Li
[ Upstream commit 4243219141b67d7c2fdb2d8073c17c539b9263eb ] In mmc_queue_setup_discard() the mmc driver queue's discard_granularity might be set as 0 (when card->pref_erase > max_discard) while the mmc device still declares to support discard operation. This is buggy and triggered the following kernel warning message, WARNING: CPU: 0 PID: 135 at __blkdev_issue_discard+0x200/0x294 CPU: 0 PID: 135 Comm: f2fs_discard-17 Not tainted 5.9.0-rc6 #1 Hardware name: Google Kevin (DT) pstate: 00000005 (nzcv daif -PAN -UAO BTYPE=--) pc : __blkdev_issue_discard+0x200/0x294 lr : __blkdev_issue_discard+0x54/0x294 sp : ffff800011dd3b10 x29: ffff800011dd3b10 x28: 0000000000000000 x27: ffff800011dd3cc4 x26: ffff800011dd3e18 x25: 000000000004e69b x24: 0000000000000c40 x23: ffff0000f1deaaf0 x22: ffff0000f2849200 x21: 00000000002734d8 x20: 0000000000000008 x19: 0000000000000000 x18: 0000000000000000 x17: 0000000000000000 x16: 0000000000000000 x15: 0000000000000000 x14: 0000000000000394 x13: 0000000000000000 x12: 0000000000000000 x11: 0000000000000000 x10: 00000000000008b0 x9 : ffff800011dd3cb0 x8 : 000000000004e69b x7 : 0000000000000000 x6 : ffff0000f1926400 x5 : ffff0000f1940800 x4 : 0000000000000000 x3 : 0000000000000c40 x2 : 0000000000000008 x1 : 00000000002734d8 x0 : 0000000000000000 Call trace: __blkdev_issue_discard+0x200/0x294 __submit_discard_cmd+0x128/0x374 __issue_discard_cmd_orderly+0x188/0x244 __issue_discard_cmd+0x2e8/0x33c issue_discard_thread+0xe8/0x2f0 kthread+0x11c/0x120 ret_from_fork+0x10/0x1c ---[ end trace e4c8023d33dfe77a ]--- This patch fixes the issue by setting discard_granularity as SECTOR_SIZE instead of 0 when (card->pref_erase > max_discard) is true. Now no more complain from __blkdev_issue_discard() for the improper value of discard granularity. This issue is exposed after commit b35fd7422c2f ("block: check queue's limits.discard_granularity in __blkdev_issue_discard()"), a "Fixes:" tag is also added for the commit to make sure people won't miss this patch after applying the change of __blkdev_issue_discard(). Fixes: e056a1b5b67b ("mmc: queue: let host controllers specify maximum discard timeout") Fixes: b35fd7422c2f ("block: check queue's limits.discard_granularity in __blkdev_issue_discard()"). Reported-and-tested-by: Vicente Bergas <vicencb@gmail.com> Signed-off-by: Coly Li <colyli@suse.de> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Cc: Ulf Hansson <ulf.hansson@linaro.org> Link: https://lore.kernel.org/r/20201002013852.51968-1-colyli@suse.de Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2020-10-07mmc: sdhci: Workaround broken command queuing on Intel GLK based IRBIS modelsHans de Goede
commit afd7f30886b0b445a4240a99020458a9772f2b89 upstream. Commit bedf9fc01ff1 ("mmc: sdhci: Workaround broken command queuing on Intel GLK"), disabled command-queuing on Intel GLK based LENOVO models because of it being broken due to what is believed to be a bug in the BIOS. It seems that the BIOS of some IRBIS models, including the IRBIS NB111 model has the same issue, so disable command queuing there too. Fixes: bedf9fc01ff1 ("mmc: sdhci: Workaround broken command queuing on Intel GLK") BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=209397 Reported-and-tested-by: RussianNeuroMancer <russianneuromancer@ya.ru> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Link: https://lore.kernel.org/r/20200927104821.5676-1-hdegoede@redhat.com Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-10-01mmc: core: Fix size overflow for mmc partitionsBradley Bolen
[ Upstream commit f3d7c2292d104519195fdb11192daec13229c219 ] With large eMMC cards, it is possible to create general purpose partitions that are bigger than 4GB. The size member of the mmc_part struct is only an unsigned int which overflows for gp partitions larger than 4GB. Change this to a u64 to handle the overflow. Signed-off-by: Bradley Bolen <bradleybolen@gmail.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2020-09-17mmc: sdhci-msm: Add retries when all tuning phases are found validDouglas Anderson
[ Upstream commit 9d5dcefb7b114d610aeb2371f6a6f119af316e43 ] As the comments in this patch say, if we tune and find all phases are valid it's _almost_ as bad as no phases being found valid. Probably all phases are not really reliable but we didn't detect where the unreliable place is. That means we'll essentially be guessing and hoping we get a good phase. This is not just a problem in theory. It was causing real problems on a real board. On that board, most often phase 10 is found as the only invalid phase, though sometimes 10 and 11 are invalid and sometimes just 11. Some percentage of the time, however, all phases are found to be valid. When this happens, the current logic will decide to use phase 11. Since phase 11 is sometimes found to be invalid, this is a bad choice. Sure enough, when phase 11 is picked we often get mmc errors later in boot. I have seen cases where all phases were found to be valid 3 times in a row, so increase the retry count to 10 just to be extra sure. Fixes: 415b5a75da43 ("mmc: sdhci-msm: Add platform_execute_tuning implementation") Signed-off-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Link: https://lore.kernel.org/r/20200827075809.1.If179abf5ecb67c963494db79c3bc4247d987419b@changeid Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2020-08-21mmc: renesas_sdhi_internal_dmac: clean up the code for dma completeYoshihiro Shimoda
[ Upstream commit 2b26e34e9af3fa24fa1266e9ea2d66a1f7d62dc0 ] To add end() operation in the future, clean the code of renesas_sdhi_internal_dmac_complete_tasklet_fn(). No behavior change. Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Link: https://lore.kernel.org/r/1590044466-28372-3-git-send-email-yoshihiro.shimoda.uh@renesas.com Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2020-07-22mmc: sdhci: do not enable card detect interrupt for gpio cd typeHaibo Chen
[ Upstream commit e65bb38824711559844ba932132f417bc5a355e2 ] Except SDHCI_QUIRK_BROKEN_CARD_DETECTION and MMC_CAP_NONREMOVABLE, we also do not need to handle controller native card detect interrupt for gpio cd type. If we wrong enabled the card detect interrupt for gpio case, it will cause a lot of unexpected card detect interrupts during data transfer which should not happen. Signed-off-by: Haibo Chen <haibo.chen@nxp.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/1582100563-20555-2-git-send-email-haibo.chen@nxp.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2020-06-22mmc: sdhci-esdhc-imx: fix the mask for tuning start pointHaibo Chen
[ Upstream commit 1194be8c949b8190b2882ad8335a5d98aa50c735 ] According the RM, the bit[6~0] of register ESDHC_TUNING_CTRL is TUNING_START_TAP, bit[7] of this register is to disable the command CRC check for standard tuning. So fix it here. Fixes: d87fc9663688 ("mmc: sdhci-esdhc-imx: support setting tuning start point") Signed-off-by: Haibo Chen <haibo.chen@nxp.com> Link: https://lore.kernel.org/r/1590488522-9292-1-git-send-email-haibo.chen@nxp.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2020-06-22mmc: via-sdmmc: Respect the cmd->busy_timeout from the mmc coreUlf Hansson
[ Upstream commit 966244ccd2919e28f25555a77f204cd1c109cad8 ] Using a fixed 1s timeout for all commands (and data transfers) is a bit problematic. For some commands it means waiting longer than needed for the timer to expire, which may not a big issue, but still. For other commands, like for an erase (CMD38) that uses a R1B response, may require longer timeouts than 1s. In these cases, we may end up treating the command as it failed, while it just needed some more time to complete successfully. Fix the problem by respecting the cmd->busy_timeout, which is provided by the mmc core. Cc: Bruce Chang <brucechang@via.com.tw> Cc: Harald Welte <HaraldWelte@viatech.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Link: https://lore.kernel.org/r/20200414161413.3036-17-ulf.hansson@linaro.org Signed-off-by: Sasha Levin <sashal@kernel.org>
2020-06-22mmc: sdhci-msm: Set SDHCI_QUIRK_MULTIBLOCK_READ_ACMD12 quirkVeerabhadrarao Badiganti
[ Upstream commit d863cb03fb2aac07f017b2a1d923cdbc35021280 ] sdhci-msm can support auto cmd12. So enable SDHCI_QUIRK_MULTIBLOCK_READ_ACMD12 quirk. Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Link: https://lore.kernel.org/r/1587363626-20413-3-git-send-email-vbadigan@codeaurora.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2020-06-22mmc: meson-mx-sdio: trigger a soft reset after a timeout or CRC errorMartin Blumenstingl
[ Upstream commit 91995b904ec2e44b5c159ac6a5d3f154345a4de7 ] The vendor driver (from the 3.10 kernel) triggers a soft reset every time before starting a new command. While this fixes a problem where SDIO cards are not detected at all (because all commands simply timed out) this hurts SD card read performance a bit (in my tests between 10% to 20%). Trigger a soft reset after we got a CRC error or if the previous command timed out (just like the vendor driver from the same 3.10 kernel for the newer SDHC controller IP does). This fixes detection of SDIO cards and doesn't hurt SD card read performance at the same time. With this patch the initialization of an RTL8723BS SDIO card looks like this: req done (CMD52): -110: 00000000 00000000 00000000 00000000 clock 400000Hz busmode 2 powermode 2 cs 1 Vdd 21 width 1 timing 0 starting CMD0 arg 00000000 flags 000000c0 req done (CMD0): 0: 00000000 00000000 00000000 00000000 clock 400000Hz busmode 2 powermode 2 cs 0 Vdd 21 width 1 timing 0 starting CMD8 arg 000001aa flags 000002f5 req done (CMD8): -110: 00000000 00000000 00000000 00000000 starting CMD5 arg 00000000 flags 000002e1 req done (CMD5): 0: 90ff0000 00000000 00000000 00000000 starting CMD5 arg 00200000 flags 000002e1 req done (CMD5): 0: 90ff0000 00000000 00000000 00000000 starting CMD3 arg 00000000 flags 00000075 req done (CMD3): 0: 00010000 00000000 00000000 00000000 starting CMD7 arg 00010000 flags 00000015 req done (CMD7): 0: 00001e00 00000000 00000000 00000000 starting CMD52 arg 00000000 flags 00000195 req done (CMD52): 0: 00001032 00000000 00000000 00000000 [... more CMD52 omitted ...] clock 400000Hz busmode 2 powermode 2 cs 0 Vdd 21 width 1 timing 2 clock 50000000Hz busmode 2 powermode 2 cs 0 Vdd 21 width 1 timing 2 starting CMD52 arg 00000e00 flags 00000195 req done (CMD52): 0: 00001000 00000000 00000000 00000000 starting CMD52 arg 80000e02 flags 00000195 req done (CMD52): 0: 00001002 00000000 00000000 00000000 clock 50000000Hz busmode 2 powermode 2 cs 0 Vdd 21 width 4 timing 2 starting CMD52 arg 00020000 flags 00000195 req done (CMD52): 0: 00001007 00000000 00000000 00000000 [... more CMD52 omitted ...] new high speed SDIO card at address 0001 Fixes: ed80a13bb4c4c9 ("mmc: meson-mx-sdio: Add a driver for the Amlogic Meson8 and Meson8b SoCs") Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Link: https://lore.kernel.org/r/20200503222805.2668941-1-martin.blumenstingl@googlemail.com Tested-by: Tobias Baumann <017623705678@o2online.de> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2020-06-22mmc: sdio: Fix potential NULL pointer error in mmc_sdio_init_card()Ulf Hansson
commit f04086c225da11ad16d7f9a2fbca6483ab16dded upstream. During some scenarios mmc_sdio_init_card() runs a retry path for the UHS-I specific initialization, which leads to removal of the previously allocated card. A new card is then re-allocated while retrying. However, in one of the corresponding error paths we may end up to remove an already removed card, which likely leads to a NULL pointer exception. So, let's fix this. Fixes: 5fc3d80ef496 ("mmc: sdio: don't use rocr to check if the card could support UHS mode") Cc: <stable@vger.kernel.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Link: https://lore.kernel.org/r/20200430091640.455-2-ulf.hansson@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-06-22mmc: sdhci-msm: Clear tuning done flag while hs400 tuningVeerabhadrarao Badiganti
commit 9253d71011c349d5f5cc0cebdf68b4a80811b92d upstream. Clear tuning_done flag while executing tuning to ensure vendor specific HS400 settings are applied properly when the controller is re-initialized in HS400 mode. Without this, re-initialization of the qcom SDHC in HS400 mode fails while resuming the driver from runtime-suspend or system-suspend. Fixes: ff06ce417828 ("mmc: sdhci-msm: Add HS400 platform support") Cc: stable@vger.kernel.org Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org> Link: https://lore.kernel.org/r/1590678838-18099-1-git-send-email-vbadigan@codeaurora.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-06-03mmc: core: Fix recursive locking issue in CQE recovery pathSarthak Garg
commit 39a22f73744d5baee30b5f134ae2e30b668b66ed upstream. Consider the following stack trace -001|raw_spin_lock_irqsave -002|mmc_blk_cqe_complete_rq -003|__blk_mq_complete_request(inline) -003|blk_mq_complete_request(rq) -004|mmc_cqe_timed_out(inline) -004|mmc_mq_timed_out mmc_mq_timed_out acquires the queue_lock for the first time. The mmc_blk_cqe_complete_rq function also tries to acquire the same queue lock resulting in recursive locking where the task is spinning for the same lock which it has already acquired leading to watchdog bark. Fix this issue with the lock only for the required critical section. Cc: <stable@vger.kernel.org> Fixes: 1e8e55b67030 ("mmc: block: Add CQE support") Suggested-by: Sahitya Tummala <stummala@codeaurora.org> Signed-off-by: Sarthak Garg <sartgarg@codeaurora.org> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Link: https://lore.kernel.org/r/1588868135-31783-1-git-send-email-vbadigan@codeaurora.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-06-03mmc: block: Fix use-after-free issue for rpmbPeng Hao
[ Upstream commit 202500d21654874aa03243e91f96de153ec61860 ] The data structure member “rpmb->md” was passed to a call of the function “mmc_blk_put” after a call of the function “put_device”. Reorder these function calls to keep the data accesses consistent. Fixes: 1c87f7357849 ("mmc: block: Fix bug when removing RPMB chardev ") Signed-off-by: Peng Hao <richard.peng@oppo.com> Cc: stable@vger.kernel.org [Uffe: Fixed up mangled patch and updated commit message] Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2020-05-20mmc: block: Fix request completion in the CQE timeout pathAdrian Hunter
[ Upstream commit c077dc5e0620508a29497dac63a2822324ece52a ] First, it should be noted that the CQE timeout (60 seconds) is substantial so a CQE request that times out is really stuck, and the race between timeout and completion is extremely unlikely. Nevertheless this patch fixes an issue with it. Commit ad73d6feadbd7b ("mmc: complete requests from ->timeout") preserved the existing functionality, to complete the request. However that had only been necessary because the block layer timeout handler had been marking the request to prevent it from being completed normally. That restriction was removed at the same time, the result being that a request that has gone will have been completed anyway. That is, the completion was unnecessary. At the time, the unnecessary completion was harmless because the block layer would ignore it, although that changed in kernel v5.0. Note for stable, this patch will not apply cleanly without patch "mmc: core: Fix recursive locking issue in CQE recovery path" Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Fixes: ad73d6feadbd7b ("mmc: complete requests from ->timeout") Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20200508062227.23144-1-adrian.hunter@intel.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2020-05-20mmc: core: Check request type before completing the requestVeerabhadrarao Badiganti
[ Upstream commit e6bfb1bf00852b55f4c771f47ae67004c04d3c87 ] In the request completion path with CQE, request type is being checked after the request is getting completed. This is resulting in returning the wrong request type and leading to the IO hang issue. ASYNC request type is getting returned for DCMD type requests. Because of this mismatch, mq->cqe_busy flag is never getting cleared and the driver is not invoking blk_mq_hw_run_queue. So requests are not getting dispatched to the LLD from the block layer. All these eventually leading to IO hang issues. So, get the request type before completing the request. Cc: <stable@vger.kernel.org> Fixes: 1e8e55b67030 ("mmc: block: Add CQE support") Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Link: https://lore.kernel.org/r/1588775643-18037-2-git-send-email-vbadigan@codeaurora.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2020-05-20mmc: sdhci-acpi: Add SDHCI_QUIRK2_BROKEN_64_BIT_DMA for AMDI0040Raul E Rangel
[ Upstream commit 45a3fe3bf93b7cfeddc28ef7386555e05dc57f06 ] The AMD eMMC 5.0 controller does not support 64 bit DMA. Fixes: 34597a3f60b1 ("mmc: sdhci-acpi: Add support for ACPI HID of AMD Controller with HS400") Signed-off-by: Raul E Rangel <rrangel@chromium.org> Link: https://marc.info/?l=linux-mmc&m=158879884514552&w=2 Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Link: https://lore.kernel.org/r/20200508165344.1.Id5bb8b1ae7ea576f26f9d91c761df7ccffbf58c5@changeid Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2020-05-06mmc: meson-mx-sdio: remove the broken ->card_busy() opMartin Blumenstingl
commit ddca1092c4324c89cf692b5efe655aa251864b51 upstream. The recent commit 0d84c3e6a5b2 ("mmc: core: Convert to mmc_poll_for_busy() for erase/trim/discard") makes use of the ->card_busy() op for SD cards. This uncovered that the ->card_busy() op in the Meson SDIO driver was never working right: while polling the busy status with ->card_busy() meson_mx_mmc_card_busy() reads only one of the two MESON_MX_SDIO_IRQC register values 0x1f001f10 or 0x1f003f10. This translates to "three out of four DAT lines are HIGH" and "all four DAT lines are HIGH", which is interpreted as "the card is busy". It turns out that no situation can be observed where all four DAT lines are LOW, meaning the card is not busy anymore. Upon further research the 3.10 vendor driver for this controller does not implement the ->card_busy() op. Remove the ->card_busy() op from the meson-mx-sdio driver since it is not working. At the time of writing this patch it is not clear what's needed to make the ->card_busy() implementation work with this specific controller hardware. For all use-cases which have previously worked the MMC_CAP_WAIT_WHILE_BUSY flag is now taking over, even if we don't have a ->card_busy() op anymore. Fixes: ed80a13bb4c4c9 ("mmc: meson-mx-sdio: Add a driver for the Amlogic Meson8 and Meson8b SoCs") Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20200416183513.993763-3-martin.blumenstingl@googlemail.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-05-06mmc: meson-mx-sdio: Set MMC_CAP_WAIT_WHILE_BUSYMartin Blumenstingl
commit e53b868b3cf5beeaa2f851ec6740112bf4d6a8cb upstream. The Meson SDIO controller uses the DAT0 lane for hardware busy detection. Set MMC_CAP_WAIT_WHILE_BUSY accordingly. This fixes the following error observed with Linux 5.7 (pre-rc-1): mmc1: Card stuck being busy! __mmc_poll_for_busy blk_update_request: I/O error, dev mmcblk1, sector 17111080 op 0x3:(DISCARD) flags 0x0 phys_seg 1 prio class 0 Fixes: ed80a13bb4c4c9 ("mmc: meson-mx-sdio: Add a driver for the Amlogic Meson8 and Meson8b SoCs") Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20200416183513.993763-2-martin.blumenstingl@googlemail.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-05-06mmc: sdhci-msm: Enable host capabilities pertains to R1b responseVeerabhadrarao Badiganti
commit 9d8cb58691f85cef687512262acb2c7109ee4868 upstream. MSM sd host controller is capable of HW busy detection of device busy signaling over DAT0 line. And it requires the R1B response for commands that have this response associated with them. So set the below two host capabilities for qcom SDHC. - MMC_CAP_WAIT_WHILE_BUSY - MMC_CAP_NEED_RSP_BUSY Recent development of the mmc core in regards to this, revealed this as being a potential bug, hence the stable tag. Cc: <stable@vger.kernel.org> # v4.19+ Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Link: https://lore.kernel.org/r/1587363626-20413-2-git-send-email-vbadigan@codeaurora.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-05-06mmc: sdhci-pci: Fix eMMC driver strength for BYT-based controllersAdrian Hunter
commit 1a8eb6b373c2af6533c13d1ea11f504e5010ed9a upstream. BIOS writers have begun the practice of setting 40 ohm eMMC driver strength even though the eMMC may not support it, on the assumption that the kernel will validate the value against the eMMC (Extended CSD DRIVER_STRENGTH [offset 197]) and revert to the default 50 ohm value if 40 ohm is invalid. This is done to avoid changing the value for different boards. Putting aside the merits of this approach, it is clear the eMMC's mask of supported driver strengths is more reliable than the value provided by BIOS. Add validation accordingly. Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Fixes: 51ced59cc02e ("mmc: sdhci-pci: Use ACPI DSM to get driver strength for some Intel devices") Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20200422111629.4899-1-adrian.hunter@intel.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-05-06mmc: sdhci-xenon: fix annoying 1.8V regulator warningMarek Behún
commit bb32e1987bc55ce1db400faf47d85891da3c9b9f upstream. For some reason the Host Control2 register of the Xenon SDHCI controller sometimes reports the bit representing 1.8V signaling as 0 when read after it was written as 1. Subsequent read reports 1. This causes the sdhci_start_signal_voltage_switch function to report 1.8V regulator output did not become stable When CONFIG_PM is enabled, the host is suspended and resumend many times, and in each resume the switch to 1.8V is called, and so the kernel log reports this message annoyingly often. Do an empty read of the Host Control2 register in Xenon's .voltage_switch method to circumvent this. This patch fixes this particular problem on Turris MOX. Signed-off-by: Marek Behún <marek.behun@nic.cz> Fixes: 8d876bf472db ("mmc: sdhci-xenon: wait 5ms after set 1.8V...") Cc: stable@vger.kernel.org # v4.16+ Link: https://lore.kernel.org/r/20200420080444.25242-1-marek.behun@nic.cz Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-05-06mmc: cqhci: Avoid false "cqhci: CQE stuck on" by not open-coding timeout loopDouglas Anderson
commit b1ac62a7ac386d76968af5f374a4a7a82a35fe31 upstream. Open-coding a timeout loop invariably leads to errors with handling the timeout properly in one corner case or another. In the case of cqhci we might report "CQE stuck on" even if it wasn't stuck on. You'd just need this sequence of events to happen in cqhci_off(): 1. Call ktime_get(). 2. Something happens to interrupt the CPU for > 100 us (context switch or interrupt). 3. Check time and; set "timed_out" to true since > 100 us. 4. Read CQHCI_CTL. 5. Both "reg & CQHCI_HALT" and "timed_out" are true, so break. 6. Since "timed_out" is true, falsely print the error message. Rather than fixing the polling loop, use readx_poll_timeout() like many people do. This has been time tested to handle the corner cases. Fixes: a4080225f51d ("mmc: cqhci: support for command queue enabled host") Signed-off-by: Douglas Anderson <dianders@chromium.org> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20200413162717.1.Idece266f5c8793193b57a1ddb1066d030c6af8e0@changeid Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-04-02mmc: sdhci-tegra: Fix busy detection by enabling MMC_CAP_NEED_RSP_BUSYUlf Hansson
[ Upstream commit d2f8bfa4bff5028bc40ed56b4497c32e05b0178f ] It has turned out that the sdhci-tegra controller requires the R1B response, for commands that has this response associated with them. So, converting from an R1B to an R1 response for a CMD6 for example, leads to problems with the HW busy detection support. Fix this by informing the mmc core about the requirement, via setting the host cap, MMC_CAP_NEED_RSP_BUSY. Reported-by: Bitan Biswas <bbiswas@nvidia.com> Reported-by: Peter Geis <pgwipeout@gmail.com> Suggested-by: Sowjanya Komatineni <skomatineni@nvidia.com> Cc: <stable@vger.kernel.org> Tested-by: Sowjanya Komatineni <skomatineni@nvidia.com> Tested-By: Peter Geis <pgwipeout@gmail.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2020-04-02mmc: sdhci-omap: Fix busy detection by enabling MMC_CAP_NEED_RSP_BUSYUlf Hansson
[ Upstream commit 055e04830d4544c57f2a5192a26c9e25915c29c0 ] It has turned out that the sdhci-omap controller requires the R1B response, for commands that has this response associated with them. So, converting from an R1B to an R1 response for a CMD6 for example, leads to problems with the HW busy detection support. Fix this by informing the mmc core about the requirement, via setting the host cap, MMC_CAP_NEED_RSP_BUSY. Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org> Reported-by: Anders Roxell <anders.roxell@linaro.org> Reported-by: Faiz Abbas <faiz_abbas@ti.com> Cc: <stable@vger.kernel.org> Tested-by: Anders Roxell <anders.roxell@linaro.org> Tested-by: Faiz Abbas <faiz_abbas@ti.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2020-04-02mmc: core: Respect MMC_CAP_NEED_RSP_BUSY for eMMC sleep commandUlf Hansson
[ Upstream commit 18d200460cd73636d4f20674085c39e32b4e0097 ] The busy timeout for the CMD5 to put the eMMC into sleep state, is specific to the card. Potentially the timeout may exceed the host->max_busy_timeout. If that becomes the case, mmc_sleep() converts from using an R1B response to an R1 response, as to prevent the host from doing HW busy detection. However, it has turned out that some hosts requires an R1B response no matter what, so let's respect that via checking MMC_CAP_NEED_RSP_BUSY. Note that, if the R1B gets enforced, the host becomes fully responsible of managing the needed busy timeout, in one way or the other. Suggested-by: Sowjanya Komatineni <skomatineni@nvidia.com> Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200311092036.16084-1-ulf.hansson@linaro.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2020-04-02mmc: core: Respect MMC_CAP_NEED_RSP_BUSY for erase/trim/discardUlf Hansson
[ Upstream commit 43cc64e5221cc6741252b64bc4531dd1eefb733d ] The busy timeout that is computed for each erase/trim/discard operation, can become quite long and may thus exceed the host->max_busy_timeout. If that becomes the case, mmc_do_erase() converts from using an R1B response to an R1 response, as to prevent the host from doing HW busy detection. However, it has turned out that some hosts requires an R1B response no matter what, so let's respect that via checking MMC_CAP_NEED_RSP_BUSY. Note that, if the R1B gets enforced, the host becomes fully responsible of managing the needed busy timeout, in one way or the other. Suggested-by: Sowjanya Komatineni <skomatineni@nvidia.com> Cc: <stable@vger.kernel.org> Tested-by: Anders Roxell <anders.roxell@linaro.org> Tested-by: Sowjanya Komatineni <skomatineni@nvidia.com> Tested-by: Faiz Abbas <faiz_abbas@ti.com> Tested-By: Peter Geis <pgwipeout@gmail.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2020-04-02mmc: core: Allow host controllers to require R1B for CMD6Ulf Hansson
[ Upstream commit 1292e3efb149ee21d8d33d725eeed4e6b1ade963 ] It has turned out that some host controllers can't use R1B for CMD6 and other commands that have R1B associated with them. Therefore invent a new host cap, MMC_CAP_NEED_RSP_BUSY to let them specify this. In __mmc_switch(), let's check the flag and use it to prevent R1B responses from being converted into R1. Note that, this also means that the host are on its own, when it comes to manage the busy timeout. Suggested-by: Sowjanya Komatineni <skomatineni@nvidia.com> Cc: <stable@vger.kernel.org> Tested-by: Anders Roxell <anders.roxell@linaro.org> Tested-by: Sowjanya Komatineni <skomatineni@nvidia.com> Tested-by: Faiz Abbas <faiz_abbas@ti.com> Tested-By: Peter Geis <pgwipeout@gmail.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
generated by cgit 1.2.3-korg (git 2.39.0) at 2024-05-14 13:03:40 +0000