| Age | Commit message (Collapse) | Author |
|---|
|
The Raspberry Pi 4 SDHCI hardware seems to automatically issue CMD12
after multiblock reads even when ACMD12 is disabled. This triggers
spurious interrupts after the data transfer is done with the following
message:
mmc1: Got data interrupt 0x00000002 even though no data operation was in progress.
mmc1: sdhci: ============ SDHCI REGISTER DUMP ===========
mmc1: sdhci: Sys addr: 0x00000000 | Version: 0x00001002
mmc1: sdhci: Blk size: 0x00007200 | Blk cnt: 0x00000000
mmc1: sdhci: Argument: 0x00000000 | Trn mode: 0x00000033
mmc1: sdhci: Present: 0x1fff0000 | Host ctl: 0x00000017
mmc1: sdhci: Power: 0x0000000f | Blk gap: 0x00000080
mmc1: sdhci: Wake-up: 0x00000000 | Clock: 0x00000107
mmc1: sdhci: Timeout: 0x00000000 | Int stat: 0x00000000
mmc1: sdhci: Int enab: 0x03ff100b | Sig enab: 0x03ff100b
mmc1: sdhci: ACmd stat: 0x00000000 | Slot int: 0x00000000
mmc1: sdhci: Caps: 0x45ee6432 | Caps_1: 0x0000a525
mmc1: sdhci: Cmd: 0x00000c1a | Max curr: 0x00080008
mmc1: sdhci: Resp[0]: 0x00000b00 | Resp[1]: 0x00edc87f
mmc1: sdhci: Resp[2]: 0x325b5900 | Resp[3]: 0x00400e00
mmc1: sdhci: Host ctl2: 0x00000001
mmc1: sdhci: ADMA Err: 0x00000000 | ADMA Ptr: 0xf3025208
mmc1: sdhci: ============================================
Enable SDHCI_QUIRK_MULTIBLOCK_READ_ACMD12 to enable ACMD12 on multiblock
reads and suppress the spurious interrupts.
Fixes: f84e411c85be ("mmc: sdhci-iproc: Add support for emmc2 of the BCM2711")
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Tested-by: Matthias Brugger <mbrugger@suse.com>
Acked-by: Stefan Wahren <wahrenst@gmx.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The additional emmc2 interface of the BCM2711 is an improved version
of the old emmc controller, which is able to provide DDR50 mode on the
Raspberry Pi 4. Except 32 bit only register access no other quirks are
known yet.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The iproc host eMMC/SD controller hold time does not meet the
specification in the HS50 mode. This problem can be mitigated
by disabling the HISPD bit; thus forcing the controller output
data to be driven on the falling clock edges rather than the
rising clock edges.
Stable tag (v4.12+) chosen to assist stable kernel maintainers so that
the change does not produce merge conflicts backporting to older kernel
versions. In reality, the timing bug existed since the driver was first
introduced but there is no need for this driver to be supported in kernel
versions that old.
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Trac Hoang <trac.hoang@broadcom.com>
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The iproc host eMMC/SD controller hold time does not meet the
specification in the HS50 mode. This problem can be mitigated
by disabling the HISPD bit; thus forcing the controller output
data to be driven on the falling clock edges rather than the
rising clock edges.
This change applies only to the Cygnus platform.
Stable tag (v4.12+) chosen to assist stable kernel maintainers so that
the change does not produce merge conflicts backporting to older kernel
versions. In reality, the timing bug existed since the driver was first
introduced but there is no need for this driver to be supported in kernel
versions that old.
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Trac Hoang <trac.hoang@broadcom.com>
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
We need to handle mmc_of_parse() errors during probe.
This finally fixes the wifi regression on Raspberry Pi 3 series.
In error case the wifi chip was permanently in reset because of
the power sequence depending on the deferred probe of the GPIO expander.
Fixes: b580c52d58d9 ("mmc: sdhci-iproc: add IPROC SDHCI driver")
Cc: stable@vger.kernel.org
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Add ACPI support to all IPROC SDHCI variants.
Signed-off-by: Srinath Mannam <srinath.mannam@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Reviewed-by: Vladimir Olovyannikov <vladimir.olovyannikov@broadcom.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The SDHCI_QUIRK2_HOST_OFF_CARD_ON is needed for the driver to
properly reset the host controller (reset all) on initialization
after exiting deep sleep.
Signed-off-by: Corneliu Doban <corneliu.doban@broadcom.com>
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Srinath Mannam <srinath.mannam@broadcom.com>
Fixes: c833e92bbb60 ("mmc: sdhci-iproc: support standard byte register accesses")
Cc: stable@vger.kernel.org # v4.10+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
When the host controller accepts only 32bit writes, the value of the
16bit TRANSFER_MODE register, that has the same 32bit address as the
16bit COMMAND register, needs to be saved and it will be written
in a 32bit write together with the command as this will trigger the
host to send the command on the SD interface.
When sending the tuning command, TRANSFER_MODE is written and then
sdhci_set_transfer_mode reads it back to clear AUTO_CMD12 bit and
write it again resulting in wrong value to be written because the
initial write value was saved in a shadow and the read-back returned
a wrong value, from the register.
Fix sdhci_iproc_readw to return the saved value of TRANSFER_MODE
when a saved value exist.
Same fix for read of BLOCK_SIZE and BLOCK_COUNT registers, that are
saved for a different reason, although a scenario that will cause the
mentioned problem on this registers is not probable.
Fixes: b580c52d58d9 ("mmc: sdhci-iproc: add IPROC SDHCI driver")
Signed-off-by: Corneliu Doban <corneliu.doban@broadcom.com>
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Cc: stable@vger.kernel.org # v4.1+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Remove hard coded mmc cap 1.8v from platform data as it is board specific.
The 1.8v DDR mmc caps can be enabled using DTS property for those
boards that support it.
Fixes: b17b4ab8ce38 ("mmc: sdhci-iproc: define MMC caps in platform data")
Signed-off-by: Srinath Mannam <srinath.mannam@broadcom.com>
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Cc: stable@vger.kernel.org # v4.8+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
According to the BCM2835 datasheet there are no preset value registers.
This wasn't an issue before, because we didn't propagate 1.8V support.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The stingray SDHCI hardware supports ACMD12 and automatically
issues after multi block transfer completed.
If ACMD12 in SDHCI is disabled, spurious tx done interrupts are seen
on multi block read command with below error message:
Got data interrupt 0x00000002 even though no data
operation was in progress.
This patch uses SDHCI_QUIRK_MULTIBLOCK_READ_ACMD12 to enable
ACM12 support in SDHCI hardware and suppress spurious interrupt.
Signed-off-by: Srinath Mannam <srinath.mannam@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Fixes: b580c52d58d9 ("mmc: sdhci-iproc: add IPROC SDHCI driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
According to the BCM2835 datasheet the maximum block size for the
eMMC module is restricted to the internal data FIFO which is 1024 byte.
But this is still an improvement to the default of 512 byte.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Acked-by: Scott Branden <scott.branden@broadcom.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Since the mmc module on bcm2835 neither provide a capabilities register nor
free documentation we must rely on the downstream implementation [1].
So enable the following capabilities for bcm2835:
MMC_CAP_MMC_HIGHSPEED
MMC_CAP_SD_HIGHSPEED
MMC_CAP_DRIVER_TYPE_A
MMC_CAP_DRIVER_TYPE_C
[1] - https://github.com/raspberrypi/linux/blob/rpi-4.4.y/drivers/mmc/host/bcm2835-mmc.c
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Add bytewise register accesses support for newer versions of IPROC
SDHCI controllers.
Previous sdhci-iproc versions of SDIO controllers
(such as Raspberry Pi and Cygnus) only allowed for 32-bit register
accesses.
Signed-off-by: Srinath Mannam <srinath.mannam@broadcom.com>
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Due to previous changes this define has no longer a purpose. Instead move
the sdhci-pltfm drivers over to use the exported struct sdhci_pltfm_pmops.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The capabilities in iproc platform data are magic numbers. So
replace them with the proper capability defines to make it
readable.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Scott Branden <scott.branden@broadcom.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The sdhci_iproc_remove() is jsut a wrapper to sdhci_pltfm_unregister.
So use the sdhci_pltfm_unregister() for the .remove hook directly.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Scott Branden from Broadcom said that the BCM2835 eMMC IP core is
very similar to IPROC and share most of the quirks. So use this driver
instead of separate one.
The sdhci-iproc contains a better workaround for the clock domain
crossing problem which doesn't need any delays. This results in a
better write performance.
Btw we get the rid of the SDHCI_CAPABILITIES hack in the sdhci_readl
function.
Suggested-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Eric Anholt <eric@anholt.net>
Acked-by: Scott Branden <sbranden@broadcom.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
This patch moves the definition of the MMC capabilities
from the probe function into iproc platform data. After
that we are able to add support for another platform more
easily.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Suggested-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Scott Branden <sbranden@broadcom.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The RPi firmware-based clocks driver can actually disable
unused clocks, so when switching to use it we ended up losing
our MMC clock once all devices were probed.
This patch adopts the changes from 1e5a0a9a58e2 ("mmc: sdhci-bcm2835:
Actually enable the clock") to sdhci-iproc.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
This patch adopts the changes from 475c9e43bfa7 ("mmc: sdhci-bcm2835:
Clean up platform allocations if sdhci init fails") to sdhci-iproc.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The driver co-allocates sdhci_iproc_host with sdhci_pltfm_host and so to
access it we need to use sdhci_pltfm_priv() and not pltfm_host->priv.
Signed-off-by: Dmitry Torokhov <dtor@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Add IPROC SDHCI driver for IPROC family of Broadcom devices.
Acked-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Corneliu Doban <cdoban@broadcom.com>
Signed-off-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
Nicolas Saenz Julienne
Stefan Wahren
Trac Hoang
Stefan Wahren
Srinath Mannam
Corneliu Doban
Scott Branden
Ulf Hansson
Jisheng Zhang
Dmitry Torokhov
Scott Branden