| Age | Commit message (Collapse) | Author |
|---|
|
commit a75bfc824a2d33f57ebdc003bfe6b7a9e11e9cb9 upstream.
When changing to use suspend-to-idle to save power, the PMIC irq can not
wakeup the system due to lack of wakeup capability, which will cause
the sub-irqs (such as power key) of the PMIC can not wake up the system.
Thus we can add the wakeup capability for PMIC irq to solve this issue,
as well as removing the IRQF_NO_SUSPEND flag to allow PMIC irq to be
a wakeup source.
Reported-by: Chunyan Zhang <zhang.lyra@gmail.com>
Signed-off-by: Baolin Wang <baolin.wang7@gmail.com>
Tested-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 8ce24f8967df2836b4557a23e74dc4bb098249f1 ]
This code should clean up if sm501_init_dev() fails.
Fixes: b6d6454fdb66 ("[PATCH] mfd: SM501 core driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b195e101580db390f50b0d587b7f66f241d2bc88 ]
If a child device calls mfd_cell_{en,dis}able() without an appropriate
call-back being set, we are likely to encounter a panic. Avoid this
by adding suitable checking.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 3ea2e4eab64cefa06055bb0541fcdedad4b48565 ]
Intel Emmitsburg PCH has the same LPSS than Intel Ice Lake.
Add the new IDs to the list of supported devices.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 3d858942250820b9adc35f963a257481d6d4c81d ]
The event handler loop must be run with interrupts disabled.
Otherwise we will have a warning:
[ 1970.785649] irq 31 handler lineevent_irq_handler+0x0/0x20 enabled interrupts
[ 1970.792739] WARNING: CPU: 0 PID: 0 at kernel/irq/handle.c:159 __handle_irq_event_percpu+0x162/0x170
[ 1970.860732] RIP: 0010:__handle_irq_event_percpu+0x162/0x170
...
[ 1970.946994] Call Trace:
[ 1970.949446] <IRQ>
[ 1970.951471] handle_irq_event_percpu+0x2c/0x80
[ 1970.955921] handle_irq_event+0x23/0x43
[ 1970.959766] handle_simple_irq+0x57/0x70
[ 1970.963695] generic_handle_irq+0x42/0x50
[ 1970.967717] dln2_rx+0xc1/0x210 [dln2]
[ 1970.971479] ? usb_hcd_unmap_urb_for_dma+0xa6/0x1c0
[ 1970.976362] __usb_hcd_giveback_urb+0x77/0xe0
[ 1970.980727] usb_giveback_urb_bh+0x8e/0xe0
[ 1970.984837] tasklet_action_common.isra.0+0x4a/0xe0
...
Recently xHCI driver switched to tasklets in the commit 36dc01657b49
("usb: host: xhci: Support running urb giveback in tasklet context").
The handle_irq_event_* functions are expected to be called with interrupts
disabled and they rightfully complain here because we run in tasklet context
with interrupts enabled.
Use a event spinlock to protect event handler from being interrupted.
Note, that there are only two users of this GPIO and ADC drivers and both of
them are using generic_handle_irq() which makes above happen.
Fixes: 338a12814297 ("mfd: Add support for Diolan DLN-2 devices")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ddff6c45b21d0437ce0c85f8ac35d7b5480513d7 ]
Whilst it doesn't matter if the internal 32k clock register settings
are cleaned up on exit, as the part will be turned off losing any
settings, hence the driver hasn't historially bothered. The external
clock should however be cleaned up, as it could cause clocks to be
left on, and will at best generate a warning on unbind.
Add clean up on both the probe error path and unbind for the 32k
clock.
Fixes: cdd8da8cc66b ("mfd: arizona: Add gating of external MCLKn clocks")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit d4f9b5428b53dd67f49ee8deed8d4366ed6b1933 ]
WM8994 chip has built-in regulators, which might be used for chip
operation. They are controlled by a separate wm8994-regulator driver,
which should be loaded before this driver calls regulator_get(), because
that driver also provides consumer-supply mapping for the them. If that
driver is not yet loaded, regulator core substitute them with dummy
regulator, what breaks chip operation, because the built-in regulators are
never enabled. Fix this by annotating this driver with MODULE_SOFTDEP()
"pre" dependency to "wm8994_regulator" module.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit a8ff78f7f773142eb8a8befe5a95dd6858ebd635 upstream.
Some BIOS erroneously specifies write-combining BAR for intel-lpss-pci
in MTRR. This will cause the system to hang during boot. If possible,
this bug could be corrected with a firmware update.
This patch use devm_ioremap_uc to overwrite/ignore the MTRR settings
by forcing the use of strongly uncachable pages for intel-lpss.
The BIOS bug is present on Dell XPS 13 7390 2-in-1:
[ 0.001734] 5 base 4000000000 mask 6000000000 write-combining
4000000000-7fffffffff : PCI Bus 0000:00
4000000000-400fffffff : 0000:00:02.0 (i915)
4010000000-4010000fff : 0000:00:15.0 (intel-lpss-pci)
Link: https://bugzilla.kernel.org/show_bug.cgi?id=203485
Cc: <stable@vger.kernel.org> # v4.19+
Tested-by: AceLan Kao <acelan.kao@canonical.com>
Signed-off-by: Tuowen Zhao <ztuowen@gmail.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Roman Gilg <subdiff@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit fb945c95a482200876993977008b67ea658bd938 ]
While the commit 2b8bd606b1e6 ("mfd: dln2: More sanity checking for endpoints")
tries to harden the sanity checks it made at the same time a regression,
i.e. mixed in and out endpoints. Obviously it should have been not tested on
real hardware at that time, but unluckily it didn't happen.
So, fix above mentioned typo and make device being enumerated again.
While here, introduce an enumerator for magic values to prevent similar issue
to happen in the future.
Fixes: 2b8bd606b1e6 ("mfd: dln2: More sanity checking for endpoints")
Cc: Oliver Neukum <oneukum@suse.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 2f3dc25c0118de03a00ddc88b61f7216854f534d upstream.
There is a bit which gets cleared after conversion.
Fixes: 9bb9e29c78f8 ("mfd: Add Ricoh RN5T618 PMIC core driver")
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1112ba02ff1190ca9c15a912f9269e54b46d2d82 upstream.
The watchdog driver compatible is "dlg,da9062-watchdog" and not
"dlg,da9062-wdt". Therefore the mfd-core can't populate the of_node and
fwnode. As result the watchdog driver can't parse the devicetree.
Fixes: 9b40b030c4ad ("mfd: da9062: Supply core driver")
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit dc91c3b6fe66a13ac76f6cb3b2100c0779cd3350 upstream.
On AXP288 and newer PMICs, bit 7 of AXP20X_VBUS_IPSOUT_MGMT can be set
to prevent using the VBUS input. However, when the VBUS unplugged and
plugged back in, the bit automatically resets to zero.
We need to set the register as volatile to prevent regmap from caching
that bit. Otherwise, regcache will think the bit is already set and not
write the register.
Fixes: cd53216625a0 ("mfd: axp20x: Fix axp288 volatile ranges")
Cc: stable@vger.kernel.org
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2b8bd606b1e60ca28c765f69c1eedd7d2a2e9dca upstream.
It is not enough to check for the number of endpoints.
The types must also be correct.
Reported-and-tested-by: syzbot+48a2851be24583b864dc@syzkaller.appspotmail.com
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 02f36911c1b41fcd8779fa0c135aab0554333fa5 ]
ida instances allocate some internal memory for ->free_bitmap
in addition to the base 'struct ida'. Use ida_destroy() to release
that memory at module_exit().
Fixes: 4b45efe85263 ("mfd: Add support for Intel Sunrisepoint LPSS devices")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 3f31bc67e4dc6a555341dffefe328ddd58e8b431 upstream.
It turned out Intel Gemini Lake doesn't use the same I2C timing
parameters as Broxton.
I got confirmation from the Windows team that Gemini Lake systems should
use updated timing parameters that differ from those used in Broxton
based systems.
Fixes: f80e78aa11ad ("mfd: intel-lpss: Add Intel Gemini Lake PCI IDs")
Tested-by: Chris Chiu <chiu@endlessm.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit efddff27c886e729a7f84a7205bd84d7d4af7336 ]
IRQ wake up support for MAX8997 driver was initially configured by
respective property in pdata. However, after the driver conversion to
device-tree, setting it was left as 'todo'. Nowadays most of other PMIC MFD
drivers initialized from device-tree assume that they can be an irq wakeup
source, so enable it also for MAX8997. This fixes support for wakeup from
MAX8997 RTC alarm.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9f8ddee1dab836ca758ca8fc555ab5a3aaa5d3fd ]
Power button IRQ actually has a second level of interrupts to
distinguish between UI and POWER buttons. Moreover, current
implementation looks awkward in approach to handle second level IRQs by
first level related IRQ chip.
To address above issues, split power button IRQ to be chained as well.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 55143439b7b501882bea9d95a54adfe00ffc79a3 ]
When trying to read any MC13892 ADC channel on a imx51-babbage board:
The MC13892 PMIC shutdowns completely.
After debugging this issue and comparing the MC13892 and MC13783
initializations done in the vendor kernel, it was noticed that the
CHRGRAWDIV bit of the ADC0 register was not being set.
This bit is set by default after power on, but the driver was
clearing it.
After setting this bit it is possible to read the ADC values correctly.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6b269a41a4520f7eb639e61a45ebbb9c9267d5e0 ]
Don't call runtime_put_sync when clk32k_ref is ARIZONA_32KZ_MCLK2
as there is no corresponding runtime_get_sync call.
MCLK1 is not in the AoD power domain so if it is used as 32kHz clock
source we need to hold a runtime PM reference to keep the device from
going into low power mode.
Fixes: cdd8da8cc66b ("mfd: arizona: Add gating of external MCLKn clocks")
Signed-off-by: Sapthagiri Baratam <sapthagiri.baratam@cirrus.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c974ac771479327b5424f60d58845e31daddadea ]
If a child device like touchscreen is wakeup capable, then keep ADC
interface on, so that a touching resistive screen will generate wakeup
event to the system.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 76380a607ba0b28627c9b4b55cd47a079a59624b ]
Goodix touchpad may drop its first couple input events when
i2c-designware-platdrv and intel-lpss it connects to took too long to
runtime resume from runtime suspended state.
This issue happens becuase the touchpad has a rather small buffer to
store up to 13 input events, so if the host doesn't read those events in
time (i.e. runtime resume takes too long), events are dropped from the
touchpad's buffer.
The bottleneck is D3cold delay it waits when transitioning from D3cold
to D0, hence remove the delay to make the resume faster. I've tested
some systems with intel-lpss and haven't seen any regression.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=202683
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 09fdc98577120d4f47601c3127efde726a2300c6 ]
INTEL_SOC_PMIC, INTEL_SOC_PMIC_CHTWC and MFD_TPS68470 select the
I2C_DESIGNWARE_PLATFORM without its dependencies making it possible to see
warning and build error like below:
WARNING: unmet direct dependencies detected for I2C_DESIGNWARE_PLATFORM
Depends on [n]: I2C [=y] && HAS_IOMEM [=y] && (ACPI [=y] && COMMON_CLK [=n] || !ACPI [=y])
Selected by [y]:
- MFD_TPS68470 [=y] && HAS_IOMEM [=y] && ACPI [=y] && I2C [=y]=y
/usr/bin/ld: drivers/i2c/busses/i2c-designware-platdrv.o: in function `dw_i2c_plat_resume':
i2c-designware-platdrv.c:(.text+0x62): undefined reference to `i2c_dw_prepare_clk'
/usr/bin/ld: drivers/i2c/busses/i2c-designware-platdrv.o: in function `dw_i2c_plat_suspend':
i2c-designware-platdrv.c:(.text+0x9a): undefined reference to `i2c_dw_prepare_clk'
/usr/bin/ld: drivers/i2c/busses/i2c-designware-platdrv.o: in function `dw_i2c_plat_probe':
i2c-designware-platdrv.c:(.text+0x41c): undefined reference to `i2c_dw_prepare_clk'
/usr/bin/ld: i2c-designware-platdrv.c:(.text+0x438): undefined reference to `i2c_dw_read_comp_param'
/usr/bin/ld: i2c-designware-platdrv.c:(.text+0x545): undefined reference to `i2c_dw_probe'
/usr/bin/ld: i2c-designware-platdrv.c:(.text+0x727): undefined reference to `i2c_dw_probe_slave'
Fix this by making above options to depend on I2C_DESIGNWARE_PLATFORM
being built-in. I2C_DESIGNWARE_PLATFORM is a visible symbol with
dependencies so in general the select should be avoided.
Fixes: acebcff9eda8 ("mfd: intel_soc_pmic: Select designware i2c-bus driver")
Fixes: de85d79f4aab ("mfd: Add Cherry Trail Whiskey Cove PMIC driver")
Fixes: 9bbf6a15ce19 ("mfd: Add support for TPS68470 device")
Cc: Stable <stable@vger.kernel.org> # v4.14+
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 7efd105c27fd2323789b41b64763a0e33ed79c08 ]
Since devm_regmap_init_mmio_clk can fail, add return value checking.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Chen Feng <puck.chen@hisilicon.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5da6cbcd2f395981aa9bfc571ace99f1c786c985 ]
When the driver is used with a subdevice that is disabled in the
kernel configuration, clang gets a little confused about the
control flow and fails to notice that n_subdevs is only
uninitialized when subdevs is NULL, and we check for that,
leading to a false-positive warning:
drivers/mfd/arizona-core.c:1423:19: error: variable 'n_subdevs' is uninitialized when used here
[-Werror,-Wuninitialized]
subdevs, n_subdevs, NULL, 0, NULL);
^~~~~~~~~
drivers/mfd/arizona-core.c:999:15: note: initialize the variable 'n_subdevs' to silence this warning
int n_subdevs, ret, i;
^
= 0
Ideally, we would rearrange the code to avoid all those early
initializations and have an explicit exit in each disabled case,
but it's much easier to chicken out and add one more initialization
here to shut up the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c176c6d7e932662668bcaec2d763657096589d85 ]
The logic for setting the of_node on devices created by mfd did not set
the fwnode pointer to match, which caused fwnode-based APIs to
malfunction on these devices since the fwnode pointer was null. Fix
this.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5aa3709c0a5c026735b0ddd4ec80810a23d65f5b ]
MODULE_DEVICE_TABLE(of, <of_match_table>) should be called to complete DT
OF mathing mechanism and register it.
Before this patch:
modinfo ./drivers/mfd/madera.ko | grep alias
After this patch:
modinfo ./drivers/mfd/madera.ko | grep alias
alias: of:N*T*Ccirrus,wm1840C*
alias: of:N*T*Ccirrus,wm1840
alias: of:N*T*Ccirrus,cs47l91C*
alias: of:N*T*Ccirrus,cs47l91
alias: of:N*T*Ccirrus,cs47l90C*
alias: of:N*T*Ccirrus,cs47l90
alias: of:N*T*Ccirrus,cs47l85C*
alias: of:N*T*Ccirrus,cs47l85
alias: of:N*T*Ccirrus,cs47l35C*
alias: of:N*T*Ccirrus,cs47l35
Reported-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Daniel Gomez <dagmcr@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 48171d0ea7caccf21c9ee3ae75eb370f2a756062 ]
I noticed that we can get a -EREMOTEIO errors on at least omap4 duovero:
twl6040 0-004b: Failed to write 2d = 19: -121
And then any following register access will produce errors.
There 2d offset above is register ACCCTL that gets written on twl6040
powerup. With error checking added to the related regcache_sync() call,
the -EREMOTEIO error is reproducable on twl6040 powerup at least
duovero.
To fix the error, we need to wait until twl6040 is accessible after the
powerup. Based on tests on omap4 duovero, we need to wait over 8ms after
powerup before register write will complete without failures. Let's also
make sure we warn about possible errors too.
Note that we have twl6040_patch[] reg_sequence with the ACCCTL register
configuration and regcache_sync() will write the new value to ACCCTL.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit dad06532292d77f37fbe831a02948a593500f682 ]
In virtualized setup, when system reboots due to warm
reset interrupt storm is seen.
Call Trace:
<IRQ>
dump_stack+0x70/0xa5
__report_bad_irq+0x2e/0xc0
note_interrupt+0x248/0x290
? add_interrupt_randomness+0x30/0x220
handle_irq_event_percpu+0x54/0x80
handle_irq_event+0x39/0x60
handle_fasteoi_irq+0x91/0x150
handle_irq+0x108/0x180
do_IRQ+0x52/0xf0
common_interrupt+0xf/0xf
</IRQ>
RIP: 0033:0x76fc2cfabc1d
Code: 24 28 bf 03 00 00 00 31 c0 48 8d 35 63 77 0e 00 48 8d 15 2e
94 0e 00 4c 89 f9 49 89 d9 4c 89 d3 e8 b8 e2 01 00 48 8b 54 24 18
<48> 89 ef 48 89 de 4c 89 e1 e8 d5 97 01 00 84 c0 74 2d 48 8b 04
24
RSP: 002b:00007ffd247c1fc0 EFLAGS: 00000293 ORIG_RAX: ffffffffffffffda
RAX: 0000000000000000 RBX: 00007ffd247c1ff0 RCX: 000000000003d3ce
RDX: 0000000000000000 RSI: 00007ffd247c1ff0 RDI: 000076fc2cbb6010
RBP: 000076fc2cded010 R08: 00007ffd247c2210 R09: 00007ffd247c22a0
R10: 000076fc29465470 R11: 0000000000000000 R12: 00007ffd247c1fc0
R13: 000076fc2ce8e470 R14: 000076fc27ec9960 R15: 0000000000000414
handlers:
[<000000000d3fa913>] idma64_irq
Disabling IRQ #27
To avoid interrupt storm, set the device in reset state
before bringing out the device from reset state.
Changelog v2:
- correct the subject line by adding "mfd: "
Signed-off-by: Binbin Wu <binbin.wu@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9e364e87ad7f2c636276c773d718cda29d62b741 ]
MODULE_DEVICE_TABLE(of, <of_match_table> should be called to complete DT
OF mathing mechanism and register it.
Before this patch:
modinfo drivers/mfd/tps65912-spi.ko | grep alias
alias: spi:tps65912
After this patch:
modinfo drivers/mfd/tps65912-spi.ko | grep alias
alias: of:N*T*Cti,tps65912C*
alias: of:N*T*Cti,tps65912
alias: spi:tps65912
Reported-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Daniel Gomez <dagmcr@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 20bb907f7dc82ecc9e135ad7067ac7eb69c81222 ]
Since commit 6e2bd956936 ("i2c: omap: Use noirq system sleep pm ops to idle device for suspend")
on gta04 we have handle_twl4030_pih() called in situations where pm_runtime_get()
in i2c-omap.c returns -EACCES.
[ 86.474365] Freezing remaining freezable tasks ... (elapsed 0.002 seconds) done.
[ 86.485473] printk: Suspending console(s) (use no_console_suspend to debug)
[ 86.555572] Disabling non-boot CPUs ...
[ 86.555664] Successfully put all powerdomains to target state
[ 86.563720] twl: Read failed (mod 1, reg 0x01 count 1)
[ 86.563751] twl4030: I2C error -13 reading PIH ISR
[ 86.563812] twl: Read failed (mod 1, reg 0x01 count 1)
[ 86.563812] twl4030: I2C error -13 reading PIH ISR
[ 86.563873] twl: Read failed (mod 1, reg 0x01 count 1)
[ 86.563903] twl4030: I2C error -13 reading PIH ISR
This happens when we wakeup via something behing twl4030 (powerbutton or rtc
alarm). This goes on for minutes until the system is finally resumed.
Disable the irq on suspend and enable it on resume to avoid
having i2c access problems when the irq registers are checked.
Fixes: 6e2bd956936 ("i2c: omap: Use noirq system sleep pm ops to idle device for suspend")
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit ae7b8eda27b33b1f688dfdebe4d46f690a8f9162 upstream.
There is a potential NULL pointer dereference in case devm_kzalloc()
fails and returns NULL.
Fix this by adding a NULL check on *lookup*
This bug was detected with the help of Coccinelle.
Fixes: b2e63555592f ("i2c: gpio: Convert to use descriptors")
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 9e28989d41c0eab57ec0bb156617a8757406ff8a ]
When mc13xxx_reg_read() fails, "old_adc0" is uninitialized and will
contain random value. Further execution uses "old_adc0" even when
mc13xxx_reg_read() fails.
The fix checks the return value of mc13xxx_reg_read(), and exits
the execution when it fails.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 75d4c5e03c2ae9902ab521024b10291f6fc9515b ]
Use devm_regmap_add_irq_chip and clean up error path in probe
and also the remove function.
Reported-by: Christian Hohnstaedt <Christian.Hohnstaedt@wago.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 18e294ddafaeb80a1e2e10c9bd750a6cb8388d5b ]
The driver adds different MFD child devices via mfd_add_devices() and
hence it is required to call mfd_remove_devices() to remove MFD child
devices.
Fixes: 5e0115581bbc ("cros_ec: Move cros_ec_dev module to drivers/mfd")
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ea90e7b47f0a8bd2fe14e9a88f523de7c67db90a ]
Parts of the AXP803 are compatible with their counterparts on the AXP813.
These include the GPIO, ADC, AC and battery power supplies.
Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 753a8d083e085c6f552c7982749de4cc7c40e2ac ]
In the axp20x driver, the various mfd_cell lists had varying amounts
of indentation, sometimes even within the same list. For the axp288,
there's no alignment at all.
Re-align the right hand side of the assignments with the least amount
of tabs possible. Also collapse the closing bracket and the opening
bracket of the next entry onto the same line for the axp288, to be
consistent with all the other mfd_cell lists.
This patch is whitespace change only. No functionality is modified.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4a19f9a65375ca9781b3ca9e810ece92edfc3e78 ]
As axp20x-ac-power-supply now supports AXP813, add a cell for it.
Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
Reviewed-by: Quentin Schulz <quentin.schulz@bootlin.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 04c801c18ded421845324255e660147a6f58dcd6 ]
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 504e4175829c44328773b96ad9c538e4783a8d22 ]
This is required as part of the initialization sequence on certain SoCs.
If these registers are not initialized, the hardware can be unresponsive.
This fixes the driver on apq8060 (HP TouchPad device).
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b0aff01e7aa6ad2d6998ef1323843212d1db8b04 ]
Because BD9571MWV_DVFS_MONIVDAC is not defined in the volatile table,
the physical register value is not updated by regmap and DVFS doesn't
work as expected. Fix it!
Fixes: d3ea21272094 ("mfd: Add ROHM BD9571MWV-M MFD PMIC driver")
Signed-off-by: Dien Pham <dien.pham.ry@renesas.com>
[wsa: rebase, add 'Fixes', reword commit message]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 10628e3ecf544fa2e4e24f8e112d95c37884dc98 ]
This function is supposed to return zero on success or negative error
codes on error. Unfortunately, there is a bug so it sometimes returns
non-zero, positive numbers on success.
I noticed this bug during review and I can't test it. It does appear
that the return is sometimes propogated back to _regmap_read() where all
non-zero returns are treated as failure so this may affect run time.
Fixes: 47c1697508f2 ("mfd: Align ab8500 with the abx500 interface")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit a177276aa098aa47a100d51a13eaaef029604b6d ]
If the PMIC ID is unknown, the current code would call
irq_domain_remove and panic, as pmic->irq_domain is only
initialized by mt6397_irq_init.
Return immediately with an error, if the chip ID is unsupported.
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit a3888f62fe66429fad3be7f2ba962e1e08c26fd6 ]
When building the kernel with Clang, the following section mismatch
warnings appear:
WARNING: vmlinux.o(.text+0x7239cc): Section mismatch in reference from
the function db8500_prcmu_probe() to the function
.init.text:init_prcm_registers()
The function db8500_prcmu_probe() references
the function __init init_prcm_registers().
This is often because db8500_prcmu_probe lacks a __init
annotation or the annotation of init_prcm_registers is wrong.
WARNING: vmlinux.o(.text+0x723e28): Section mismatch in reference from
the function db8500_prcmu_probe() to the function
.init.text:fw_project_name()
The function db8500_prcmu_probe() references
the function __init fw_project_name().
This is often because db8500_prcmu_probe lacks a __init
annotation or the annotation of fw_project_name is wrong.
db8500_prcmu_probe should not be marked as __init so remove the __init
annotation from fw_project_name and init_prcm_registers.
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8838555089f0345b87f4277fe5a8dd647dc65589 ]
When building the kernel with Clang, the following section mismatch
warning appears:
WARNING: vmlinux.o(.text+0x3d84a3b): Section mismatch in reference from
the function twl_probe() to the function
.init.text:unprotect_pm_master()
The function twl_probe() references
the function __init unprotect_pm_master().
This is often because twl_probe lacks a __init
annotation or the annotation of unprotect_pm_master is wrong.
Remove the __init annotation on the *protect_pm_master functions so
there is no more mismatch.
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b40ee006fe6a8a25093434e5d394128c356a48f3 ]
Use PLATFORM_DEVID_AUTO to number mfd cells while registering, so that
different instances are uniquely identified. This is required in order
to support registering of multiple instances of same ti_am335x_tscadc IP.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit ac4ca4b9f4623ba5e1ea7a582f286567c611e027 upstream.
The tps6586x driver creates an irqchip that is used by its various child
devices for managing interrupts. The tps6586x-rtc device is one of its
children that uses the tps6586x irqchip. When using the tps6586x-rtc as
a wake-up device from suspend, the following is seen:
PM: Syncing filesystems ... done.
Freezing user space processes ... (elapsed 0.001 seconds) done.
OOM killer disabled.
Freezing remaining freezable tasks ... (elapsed 0.000 seconds) done.
Disabling non-boot CPUs ...
Entering suspend state LP1
Enabling non-boot CPUs ...
CPU1 is up
tps6586x 3-0034: failed to read interrupt status
tps6586x 3-0034: failed to read interrupt status
The reason why the tps6586x interrupt status cannot be read is because
the tps6586x interrupt is not masked during suspend and when the
tps6586x-rtc interrupt occurs, to wake-up the device, the interrupt is
seen before the i2c controller has been resumed in order to read the
tps6586x interrupt status.
The tps6586x-rtc driver sets it's interrupt as a wake-up source during
suspend, which gets propagated to the parent tps6586x interrupt.
However, the tps6586x-rtc driver cannot disable it's interrupt during
suspend otherwise we would never be woken up and so the tps6586x must
disable it's interrupt instead.
Prevent the tps6586x interrupt handler from executing on exiting suspend
before the i2c controller has been resumed by disabling the tps6586x
interrupt on entering suspend and re-enabling it on resuming from
suspend.
Cc: stable@vger.kernel.org
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 48a2ca0ee3994df53da230c7079a18a70ec914f9 upstream.
This reverts commit 3aa2177e47878f7e7616da8a2050c44f22301b6e.
That commit triggered a new WARN when unloading the module (see at the
end of the commit message). When a class_dev is embedded in a structure
then that class_dev is the thing that controls the lifetime of that
structure, for that reason device managed allocations can't be used here.
See Documentation/kobject.txt.
Revert the above patch, so the struct is allocated using kzalloc and we
have a release function for it that frees the allocated memory, otherwise
it is broken.
------------[ cut here ]------------
Device 'cros_ec' does not have a release() function, it is broken and must be fixed.
WARNING: CPU: 3 PID: 3675 at drivers/base/core.c:895 device_release+0x80/0x90
Modules linked in: btusb btrtl btintel btbcm bluetooth ...
CPU: 3 PID: 3675 Comm: rmmod Not tainted 4.20.0-rc4 #76
Hardware name: Google Kevin (DT)
pstate: 40000005 (nZcv daif -PAN -UAO)
pc : device_release+0x80/0x90
lr : device_release+0x80/0x90
sp : ffff00000c47bc70
x29: ffff00000c47bc70 x28: ffff8000e86b0d40
x27: 0000000000000000 x26: 0000000000000000
x25: 0000000056000000 x24: 0000000000000015
x23: ffff8000f0bbf860 x22: ffff000000d320a0
x21: ffff8000ee93e100 x20: ffff8000ed931428
x19: ffff8000ed931418 x18: 0000000000000020
x17: 0000000000000000 x16: 0000000000000000
x15: 0000000000000400 x14: 0000000000000143
x13: 0000000000000000 x12: 0000000000000400
x11: 0000000000000157 x10: 0000000000000960
x9 : ffff00000c47b9b0 x8 : ffff8000e86b1700
x7 : 0000000000000000 x6 : ffff8000f7d520b8
x5 : ffff8000f7d520b8 x4 : 0000000000000000
x3 : ffff8000f7d58e68 x2 : ffff8000e86b0d40
x1 : 37d859939c964800 x0 : 0000000000000000
Call trace:
device_release+0x80/0x90
kobject_put+0x74/0xe8
device_unregister+0x20/0x30
ec_device_remove+0x34/0x48 [cros_ec_dev]
platform_drv_remove+0x28/0x48
device_release_driver_internal+0x1a8/0x240
driver_detach+0x40/0x80
bus_remove_driver+0x54/0xa8
driver_unregister+0x2c/0x58
platform_driver_unregister+0x10/0x18
cros_ec_dev_exit+0x1c/0x2d8 [cros_ec_dev]
__arm64_sys_delete_module+0x16c/0x1f8
el0_svc_common+0x84/0xd8
el0_svc_handler+0x2c/0x80
el0_svc+0x8/0xc
---[ end trace a57c4625f3c60ae8 ]---
Cc: stable@vger.kernel.org
Fixes: 3aa2177e4787 ("mfd: cros_ec: Use devm_kzalloc for private data")
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Reviewed-by: Dmitry Torokhov <dtor@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 9612f8f503804d2fd2f63aa6ba1e58bba4612d96 ]
The IRQ work is added before the struct rtc is allocated and registered,
but this struct is used in the IRQ handler. This may lead to a NULL pointer
dereference.
Switch to devm_rtc_allocate_device/rtc_register_device to allocate the rtc
before calling menelaus_add_irq_work.
Also, this solves a possible leak as the RTC is never released.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
It currently only works if the parent bus uses "simple-bus". We
currently try to probe children with non-existing compatible values.
And we're missing .probe.
I noticed this while testing devices configured to probe using ti-sysc
interconnect target module driver. For that we also may want to rebind
the driver, so let's remove __init and __exit.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
- the core has now a lockless variant of i2c_smbus_xfer. Some open
coded versions of this got removed in drivers. This also enables
proper SCCB support in regmap.
- locking got a more precise naming. i2c_{un}lock_adapter() had to go,
and we know use i2c_lock_bus() consistently with flags like
I2C_LOCK_ROOT_ADAPTER and I2C_LOCK_SEGMENT to avoid ambiguity.
- the gpio fault injector got a new delicate testcase
- the bus recovery procedure got fixed to handle the new testcase
correctly
- a new quirk flag for controllers not able to handle zero length
messages together with driver updates to use it
- new drivers: FSI bus attached I2C masters, GENI I2C controller, Owl
family S900
- and a good set of driver improvements and bugfixes
* 'i2c/for-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (77 commits)
i2c: rcar: implement STOP and REP_START according to docs
i2c: rcar: refactor private flags
i2c: core: ACPI: Make acpi_gsb_i2c_read_bytes() check i2c_transfer return value
i2c: core: ACPI: Properly set status byte to 0 for multi-byte writes
dt-bindings: i2c: rcar: Add r8a774a1 support
dt-bindings: i2c: sh_mobile: Add r8a774a1 support
i2c: imx: Simplify stopped state tracking
i2c: imx: Fix race condition in dma read
i2c: pasemi: remove hardcoded bus numbers on smbus
i2c: designware: Add SPDX license tag
i2c: designware: Convert to use struct i2c_timings
i2c: core: Parse SDA hold time from firmware
i2c: designware-pcidrv: Mark expected switch fall-through
i2c: amd8111: Mark expected switch fall-through
i2c: sh_mobile: use core to detect 'no zero length read' quirk
i2c: xlr: use core to detect 'no zero length' quirk
i2c: rcar: use core to detect 'no zero length' quirk
i2c: stu300: use core to detect 'no zero length' quirk
i2c: pmcmsp: use core to detect 'no zero length' quirk
i2c: mxs: use core to detect 'no zero length' quirk
...
|
Baolin Wang
Dan Carpenter
Lee Jones
Andy Shevchenko
Charles Keepax
Marek Szyprowski
Tuowen Zhao
Andreas Kemnade
Marco Felsch
Samuel Holland
Oliver Neukum
Jarkko Nikula
Fabio Estevam
Sapthagiri Baratam
Vignesh R
Kai-Heng Feng
Axel Lin
Arnd Bergmann
Robert Hancock
Daniel Gomez
Tony Lindgren
Binbin Wu
Gustavo A. R. Silva
Kangjie Lu
Keerthy
Enric Balletbo i Serra
Oskari Lemmela
Chen-Yu Tsai
Jonathan Marek
Dien Pham
Nicolas Boichat
Nathan Chancellor
Jonathan Hunter
Alexandre Belloni
Linus Torvalds