| Age | Commit message (Collapse) | Author |
|---|
|
commit 57648e860485de39c800a89f849fdd03c2d31d15 upstream.
Mark bus as suspended during system suspend to block the future
transfers. Implement geni_i2c_resume_noirq() to resume the bus.
Fixes: 37692de5d523 ("i2c: i2c-qcom-geni: Add bus driver for the Qualcomm GENI I2C controller")
Signed-off-by: Roja Rani Yarubandi <rojay@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 9f78c607600ce4f2a952560de26534715236f612 ]
If the hardware is still accessing memory after SMMU translation
is disabled (as part of smmu shutdown callback), then the
IOVAs (I/O virtual address) which it was using will go on the bus
as the physical addresses which will result in unknown crashes
like NoC/interconnect errors.
So, implement shutdown callback for i2c driver to suspend the bus
during system "reboot" or "shutdown".
Fixes: 37692de5d523 ("i2c: i2c-qcom-geni: Add bus driver for the Qualcomm GENI I2C controller")
Signed-off-by: Roja Rani Yarubandi <rojay@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 357ee8841d0b7bd822f25fc768afbc0c2ab7e47b ]
Store DMA mapping data in geni_i2c_dev struct to enhance DMA mapping
data scope. For example during shutdown callback to unmap DMA mapping,
this stored DMA mapping data can be used to call geni_se_tx_dma_unprep
and geni_se_rx_dma_unprep functions.
Add two helper functions geni_i2c_rx_msg_cleanup and
geni_i2c_tx_msg_cleanup to unwrap the things after rx/tx FIFO/DMA
transfers, so that the same can be used in geni_i2c_stop_xfer()
function during shutdown callback.
Signed-off-by: Roja Rani Yarubandi <rojay@codeaurora.org>
Reviewed-by: Akash Asthana <akashast@codeaurora.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9cb4c67d7717135d6f4600a49ab07b470ea4ee2f ]
This reverts commit 02b9aec59243c6240fc42884acc958602146ddf6.
As talked about in the patch ("soc: qcom: geni: More properly switch
to DMA mode"), swapping the order of geni_se_setup_m_cmd() and
geni_se_xx_dma_prep() can sometimes cause corrupted transfers. Thus
we traded one problem for another. Now that we've debugged the
problem further and fixed the geni helper functions to more disable
FIFO interrupts when we move to DMA mode we can revert it and end up
with (hopefully) zero problems!
To be explicit, the patch ("soc: qcom: geni: More properly switch
to DMA mode") is a prerequisite for this one.
Fixes: 02b9aec59243 ("i2c: i2c-qcom-geni: Fix DMA transfer race")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Akash Asthana <akashast@codeaurora.org>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20201013142448.v2.2.I7b22281453b8a18ab16ef2bfd4c641fb1cc6a92c@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
The code has been in a irq-disabled context since it is hard IRQ. There
is no necessity to do it again.
Signed-off-by: Barry Song <song.bao.hua@hisilicon.com>
Reviewed-by: Akash Asthana <akashast@codeaurora.org>
Reviewed-by: Mukesh Kumar Savaliya <msavaliy@codeaurora.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"A couple of subsystems have their own subsystem maintainers but choose
to have the code merged through the soc tree as upstream, as the code
tends to be used across multiple SoCs or has SoC specific drivers
itself:
- memory controllers:
Krzysztof Kozlowski takes ownership of the drivers/memory subsystem
and its drivers, starting out with a set of cleanup patches.
A larger driver for the Tegra memory controller that was
accidentally missed for v5.8 is now added.
- reset controllers:
Only minor updates to drivers/reset this time
- firmware:
The "turris mox" firmware driver gains support for signed firmware
blobs The tegra firmware driver gets extended to export some debug
information Various updates to i.MX firmware drivers, mostly
cosmetic
- ARM SCMI/SCPI:
A new mechanism for platform notifications is added, among a number
of minor changes.
- optee:
Probing of the TEE bus is rewritten to better support detection of
devices that depend on the tee-supplicant user space. A new
firmware based trusted platform module (fTPM) driver is added based
on OP-TEE
- SoC attributes:
A new driver is added to provide a generic soc_device for
identifying a machine through the SMCCC ARCH_SOC_ID firmware
interface rather than by probing SoC family specific registers.
The series also contains some cleanups to the common soc_device
code.
There are also a number of updates to SoC specific drivers, the main
ones are:
- Mediatek cmdq driver gains a few in-kernel interfaces
- Minor updates to Qualcomm RPMh, socinfo, rpm drivers, mostly adding
support for additional SoC variants
- The Qualcomm GENI core code gains interconnect path voting and
performance level support, and integrating this into a number of
device drivers.
- A new driver for Samsung Exynos5800 voltage coupler for
- Renesas RZ/G2H (R8A774E1) SoC support gets added to a couple of SoC
specific device drivers
- Updates to the TI K3 Ring Accelerator driver"
* tag 'arm-drivers-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (164 commits)
soc: qcom: geni: Fix unused label warning
soc: qcom: smd-rpm: Fix kerneldoc
memory: jz4780_nemc: Only request IO memory the driver will use
soc: qcom: pdr: Reorder the PD state indication ack
MAINTAINERS: Add Git repository for memory controller drivers
memory: brcmstb_dpfe: Fix language typo
memory: samsung: exynos5422-dmc: Correct white space issues
memory: samsung: exynos-srom: Correct alignment
memory: pl172: Enclose macro argument usage in parenthesis
memory: of: Correct kerneldoc
memory: omap-gpmc: Fix language typo
memory: omap-gpmc: Correct white space issues
memory: omap-gpmc: Use 'unsigned int' for consistency
memory: omap-gpmc: Enclose macro argument usage in parenthesis
memory: omap-gpmc: Correct kerneldoc
memory: mvebu-devbus: Align with open parenthesis
memory: mvebu-devbus: Add missing braces to all arms of if statement
memory: bt1-l2-ctl: Add blank lines after declarations
soc: TI knav_qmss: make symbol 'knav_acc_range_ops' static
firmware: ti_sci: Replace HTTP links with HTTPS ones
...
|
|
When I have KASAN enabled on my kernel and I start stressing the
touchscreen my system tends to hang. The touchscreen is one of the
only things that does a lot of big i2c transfers and ends up hitting
the DMA paths in the geni i2c driver. It appears that KASAN adds
enough delay in my system to tickle a race condition in the DMA setup
code.
When the system hangs, I found that it was running the geni_i2c_irq()
over and over again. It had these:
m_stat = 0x04000080
rx_st = 0x30000011
dm_tx_st = 0x00000000
dm_rx_st = 0x00000000
dma = 0x00000001
Notably we're in DMA mode but are getting M_RX_IRQ_EN and
M_RX_FIFO_WATERMARK_EN over and over again.
Putting some traces in geni_i2c_rx_one_msg() showed that when we
failed we were getting to the start of geni_i2c_rx_one_msg() but were
never executing geni_se_rx_dma_prep().
I believe that the problem here is that we are starting the geni
command before we run geni_se_rx_dma_prep(). If a transfer makes it
far enough before we do that then we get into the state I have
observed. Let's change the order, which seems to work fine.
Although problems were seen on the RX path, code inspection suggests
that the TX should be changed too. Change it as well.
Fixes: 37692de5d523 ("i2c: i2c-qcom-geni: Add bus driver for the Qualcomm GENI I2C controller")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Reviewed-by: Akash Asthana <akashast@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Mukesh Kumar Savaliya <msavaliy@codeaurora.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Get the interconnect paths for I2C based Serial Engine device
and vote according to the bus speed of the driver.
Signed-off-by: Akash Asthana <akashast@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Acked-by: Wolfram Sang <wsa@kernel.org>
Link: https://lore.kernel.org/r/1592908737-7068-4-git-send-email-akashast@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
This driver doesn't call any DT platform functions like of_platform_*().
Remove the include as it isn't used.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Some lines are long here. Use a struct dev pointer to shorten lines and
simplify code. The clk_get() call can fail because of EPROBE_DEFER
problems too, so just remove the error print message because it isn't
useful. Finally, platform_get_irq() already prints an error so just
remove that error message.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
We don't need to force IRQF_TRIGGER_HIGH here as the DT or ACPI tables
should take care of this for us. Just use 0 instead so that we use the
flags from the firmware. Also, remove specify dev_name() for the irq
name so that we can get better information in /proc/interrupts about
which device is generating interrupts.
Cc: Alok Chauhan <alokc@codeaurora.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
We have a production-level laptop (Lenovo Yoga C630) which is exhibiting
a rather horrific bug. When I2C HID devices are being scanned for at
boot-time the QCom Geni based I2C (Serial Engine) attempts to use DMA.
When it does, the laptop reboots and the user never sees the OS.
Attempts are being made to debug the reason for the spontaneous reboot.
No luck so far, hence the requirement for this hot-fix. This workaround
will be removed once we have a viable fix.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Tested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Add a match table to allow automatic probing of ACPI device
QCOM0220. Ignore clock attainment errors. Set default clock
frequency value.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
The Qualcomm Geni I2C driver currently probes silently which can be
confusing when debugging potential issues. Add a low level (INFO)
print when each I2C controller is successfully initially set-up.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
We need to enable runtime PM on this i2c controller before populating
child devices with i2c_add_adapter(). Otherwise, if a child device uses
runtime PM and stays runtime PM enabled we'll get the following warning
at boot.
Enabling runtime PM for inactive device (a98000.i2c) with active children
[...]
Call trace:
pm_runtime_enable+0xd8/0xf8
geni_i2c_probe+0x440/0x460
platform_drv_probe+0x74/0xc8
[...]
Let's move the runtime PM enabling and setup to before we add the
adapter, so that this device can respond to runtime PM requests from
children.
Fixes: 37692de5d523 ("i2c: i2c-qcom-geni: Add bus driver for the Qualcomm GENI I2C controller")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
We don't need to use goto here, we can just collapse the if statement
and goto chain into multiple branches and then combine some duplicate
completion calls into one big if statement. Let's do it to clean up code
some more.
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Alok Chauhan <alokc@codeaurora.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
We never really look at the 'ret' local variable in these functions, so
let's remove it to make way for shorter and simpler code. Furthermore,
we can shorten some lines by adding two local variables for the SE and
the message length so that everything fits in 80 columns and testing the
'dma_buf' local variable in lieu of the 'mode' local variable. And
kernel style is to leave the return statement by itself, detached from
the rest of the function.
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Alok Chauhan <alokc@codeaurora.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
We shouldn't attempt to DMA map the message buffers passed into this
driver from the i2c core unless the message we're mapping have been
properly setup for DMA. The i2c core indicates such a situation by
setting the I2C_M_DMA_SAFE flag, so check for that flag before using DMA
mode. We can also bounce the buffer if it isn't already mapped properly
by using the i2c_get_dma_safe_msg_buf() APIs, so do that when we
want to use DMA for a message.
This fixes a problem where the kernel oopses cleaning pages for a buffer
that's mapped into the vmalloc space. The pages are returned from
request_firmware() and passed down directly to the i2c master to write
to the i2c touchscreen device. Mapping vmalloc buffers with
dma_map_single() won't work reliably, causing an oops like below:
Unable to handle kernel paging request at virtual address ffffffc01391d000
...
Reported-by: Philip Chen <philipchen@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
This bus driver supports the GENI based i2c hardware controller in the
Qualcomm SOCs. The Qualcomm Generic Interface (GENI) is a programmable
module supporting a wide range of serial interfaces including I2C. The
driver supports FIFO mode and DMA mode of transfer and switches modes
dynamically depending on the size of the transfer.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@codeaurora.org>
Signed-off-by: Sagar Dharia <sdharia@codeaurora.org>
Signed-off-by: Girish Mahadevan <girishm@codeaurora.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Tested-by: Stephen Boyd <swboyd@chromium.org>
[wsa: squashed the MAINTAINER addition and a RPM fix by Evan Green]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
Roja Rani Yarubandi
Douglas Anderson
Barry Song
Linus Torvalds
Akash Asthana
Stephen Boyd
Lee Jones
Karthikeyan Ramasubramanian