| Age | Commit message (Collapse) | Author |
|---|
|
git://anongit.freedesktop.org/tegra/linux into drm-next
drm/tegra: Fixes for v5.6-rc1
These are a couple of quick fixes for regressions that were found during
the first two weeks of the merge window.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Thierry Reding <thierry.reding@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200206172753.2185390-1-thierry.reding@gmail.com
|
|
This partially reverts the DMA API support that was recently merged
because it was causing performance regressions on older Tegra devices.
Unfortunately, the cache maintenance performed by dma_map_sg() and
dma_unmap_sg() causes performance to drop by a factor of 10.
The right solution for this would be to cache mappings for buffers per
consumer device, but that's a bit involved. Instead, we simply revert to
the old behaviour of sharing IOVA mappings when we know that devices can
do so (i.e. they share the same IOMMU domain).
Cc: <stable@vger.kernel.org> # v5.5
Reported-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
|
|
Older Tegra devices only allow addressing 32 bits of memory, so whether
or not the host1x is attached to an IOMMU doesn't matter. host1x IOMMU
attachment is only needed on devices that can address memory beyond the
32-bit boundary and where the host1x doesn't support the wide GATHER
opcode that allows it to access buffers at higher addresses.
Cc: <stable@vger.kernel.org> # v5.5
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
|
|
Commit fd67e9c6ed5a ("drm/tegra: Do not implement runtime PM") replaced
the generic runtime PM usage by a host1x bus-specific implementation in
order to work around some assumptions baked into runtime PM that are in
conflict with the requirements in the Tegra DRM driver.
Unfortunately the new runtime PM callbacks are not setup yet at the time
when the SOR driver first needs to resume the device to register the SOR
pad clock, and accesses to register will cause the system to hang.
Note that this only happens on Tegra124 and Tegra210 because those are
the only SoCs where the SOR pad clock is registered from the SOR driver.
Later generations use a SOR pad clock provided by the BPMP.
Fix this by moving the registration of the SOR pad clock after the
host1x client has been registered. That's somewhat suboptimal because
this could potentially, though it's very unlikely, cause the Tegra DRM
to be probed if the SOR happens to be the last subdevice to register,
only to be immediately removed again if the SOR pad output clock fails
to register. That's just a minor annoyance, though, and doesn't justify
implementing a workaround.
Fixes: fd67e9c6ed5a ("drm/tegra: Do not implement runtime PM")
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
If the driver fails to probe, make sure to disable runtime PM again.
While at it, make the cleanup code in ->remove() symmetric.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Make sure the SOR module is suspenden after we fail to register the SOR
pad output clock.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
git://anongit.freedesktop.org/tegra/linux into drm-next
drm/tegra: Changes for v5.6-rc1
This contains a small set of mostly fixes and some minor improvements.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Thierry Reding <thierry.reding@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200111004835.2412858-1-thierry.reding@gmail.com
|
|
Implement generic system suspend/resume functions that can be used with
any output type. Currently this only implements disabling and enabling
of the IRQ functionality across system suspend/resume. This prevents an
interrupt from happening before the display driver has fully resumed.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Without CONFIG_PM, some functions cause harmless warnings:
drivers/gpu/drm/tegra/sor.c:3984:12: error: 'tegra_sor_resume' defined but not used [-Werror=unused-function]
static int tegra_sor_resume(struct device *dev)
^~~~~~~~~~~~~~~~
drivers/gpu/drm/tegra/sor.c:3970:12: error: 'tegra_sor_suspend' defined but not used [-Werror=unused-function]
static int tegra_sor_suspend(struct device *dev)
^~~~~~~~~~~~~~~~~
Mark these as __maybe_unused so the compiler can drop them
silently.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The Tegra DRM driver heavily relies on the implementations for runtime
suspend/resume to be called at specific times. Unfortunately, there are
some cases where that doesn't work. One example is if the user disables
runtime PM for a given subdevice. Another example is that the PM core
acquires a reference to runtime PM during system sleep, effectively
preventing devices from going into low power modes. This is intentional
to avoid nasty race conditions, but it also causes system sleep to not
function properly on all Tegra systems.
Fix this by not implementing runtime PM at all. Instead, a minimal,
reference-counted suspend/resume infrastructure is added to the host1x
bus. This has the benefit that it can be used regardless of the system
power state (or any transitions we might be in), or whether or not the
user allows runtime PM.
Atomic modesetting guarantees that these functions will end up being
called at the right point in time, so the pitfalls for the more generic
runtime PM do not apply here.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Rename the host1x clients' parent to "host" because that more closely
describes what it is. The parent can be confused with the parent device
in terms of the device hierarchy. Subsequent patches will add a new
member that refers to the parent in that hierarchy.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Use the ddc pointer provided by the generic connector.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200102132300.24309-2-andrzej.p@collabora.com
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v5.6:
UAPI Changes:
- Add support for DMA-BUF HEAPS.
Cross-subsystem Changes:
- mipi dsi definition updates, pulled into drm-intel as well.
- Add lockdep annotations for dma_resv vs mmap_sem and fs_reclaim.
- Remove support for dma-buf kmap/kunmap.
- Constify fb_ops in all fbdev drivers, including drm drivers and drm-core, and media as well.
Core Changes:
- Small cleanups to ttm.
- Fix SCDC definition.
- Assorted cleanups to core.
- Add todo to remove load/unload hooks, and use generic fbdev emulation.
- Assorted documentation updates.
- Use blocking ww lock in ttm fault handler.
- Remove drm_fb_helper_fbdev_setup/teardown.
- Warning fixes with W=1 for atomic.
- Use drm_debug_enabled() instead of drm_debug flag testing in various drivers.
- Fallback to nontiled mode in fbdev emulation when not all tiles are present. (Later on reverted)
- Various kconfig indentation fixes in core and drivers.
- Fix freeing transactions in dp-mst correctly.
- Sean Paul is steping down as core maintainer. :-(
- Add lockdep annotations for atomic locks vs dma-resv.
- Prevent use-after-free for a bad job in drm_scheduler.
- Fill out all block sizes in the P01x and P210 definitions.
- Avoid division by zero in drm/rect, and fix bounds.
- Add drm/rect selftests.
- Add aspect ratio and alternate clocks for HDMI 4k modes.
- Add todo for drm_framebuffer_funcs and fb_create cleanup.
- Drop DRM_AUTH for prime import/export ioctls.
- Clear DP-MST payload id tables downstream when initializating.
- Fix for DSC throughput definition.
- Add extra FEC definitions.
- Fix fake offset in drm_gem_object_funs.mmap.
- Stop using encoder->bridge in core directly
- Handle bridge chaining slightly better.
- Add backlight support to drm/panel, and use it in many panel drivers.
- Increase max number of y420 modes from 128 to 256, as preparation to add the new modes.
Driver Changes:
- Small fixes all over.
- Fix documentation in vkms.
- Fix mmap_sem vs dma_resv in nouveau.
- Small cleanup in komeda.
- Add page flip support in gma500 for psb/cdv.
- Add ddc symlink in the connector sysfs directory for many drivers.
- Add support for analogic an6345, and fix small bugs in it.
- Add atomic modesetting support to ast.
- Fix radeon fault handler VMA race.
- Switch udl to use generic shmem helpers.
- Unconditional vblank handling for mcde.
- Miscellaneous fixes to mcde.
- Tweak debug output from komeda using debugfs.
- Add gamma and color transform support to komeda for DOU-IPS.
- Add support for sony acx424AKP panel.
- Various small cleanups to gma500.
- Use generic fbdev emulation in udl, and replace udl_framebuffer with generic implementation.
- Add support for Logic PD Type 28 panel.
- Use drm_panel_* wrapper functions in exynos/tegra/msm.
- Add devicetree bindings for generic DSI panels.
- Don't include drm_pci.h directly in many drivers.
- Add support for begin/end_cpu_access in udmabuf.
- Stop using drm_get_pci_dev in gma500 and mga200.
- Fixes to UDL damage handling, and use dma_buf_begin/end_cpu_access.
- Add devfreq thermal support to panfrost.
- Fix hotplug with daisy chained monitors by removing VCPI when disabling topology manager.
- meson: Add support for OSD1 plane AFBC commit.
- Stop displaying garbage when toggling ast primary plane on/off.
- More cleanups and fixes to UDL.
- Add D32 suport to komeda.
- Remove globle copy of drm_dev in gma500.
- Add support for Boe Himax8279d MIPI-DSI LCD panel.
- Add support for ingenic JZ4770 panel.
- Small null pointer deference fix in ingenic.
- Remove support for the special tfp420 driver, as there is a generic way to do it.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ba73535a-9334-5302-2e1f-5208bd7390bd@linux.intel.com
|
|
To facilitate moving connector creation to display drivers,
decouple the drm_connector from drm_panel.
This patch adds a connector argument to drm_panel_get_modes().
All users of drm_panel_get_modes() already had the connector
available, so updating users was trivial.
With this patch drm_panel no longer keeps a reference to the drm_connector.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Jernej Skrabec <jernej.skrabec@siol.net>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Joonyoung Shim <jy0922.shim@samsung.com>
Cc: Seung-Woo Kim <sw0312.kim@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Alison Wang <alison.wang@nxp.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: CK Hu <ck.hu@mediatek.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Cc: Sandy Huang <hjc@rock-chips.com>
Cc: "Heiko Stübner" <heiko@sntech.de>
Cc: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Cc: Vincent Abriou <vincent.abriou@st.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Torsten Duwe <duwe@lst.de>
Cc: Vasily Khoruzhick <anarsoul@gmail.com>
Cc: Icenowy Zheng <icenowy@aosc.io>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Boris Brezillon <boris.brezillon@collabora.com>
Cc: Hariprasad Kelam <hariprasad.kelam@gmail.com>
Cc: Alexios Zavras <alexios.zavras@intel.com>
Cc: Brian Masney <masneyb@onstation.org>
Cc: Rob Clark <robdclark@chromium.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Allison Randal <allison@lohutok.net>
Cc: Shayenne Moura <shayenneluzmoura@gmail.com>
Cc: Abhinav Kumar <abhinavk@codeaurora.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: linux-mediatek@lists.infradead.org
Cc: linux-renesas-soc@vger.kernel.org
Cc: linux-rockchip@lists.infradead.org
Cc: linux-tegra@vger.kernel.org
Link: https://patchwork.freedesktop.org/patch/msgid/20191207140353.23967-7-sam@ravnborg.org
|
|
Now that the fbops member of struct fb_info is const, we can start
making the ops const as well.
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/59b43629ac60031c5bbf961d8c49695019bc9c6f.1575390740.git.jani.nikula@intel.com
|
|
The call to tegra_display_hub_cleanup() that takes care of disabling the
window groups is missing from the driver's ->remove() callback. Call it
to make sure the runtime PM reference counts for the display controllers
are balanced.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The SOR supports multiple display modes, but only when driving an HDMI
monitor does it make sense to control the +5V power supply. eDP and DP
don't need this, so make it optional.
This fixes a crash observed during system suspend/resume.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Subdevices may not be hooked up to an IOMMU via device tree. Detect such
situations and avoid confusing users by not emitting an error message.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Export the module device table to ensure the VIC compatible strings are
listed in the module's aliases table. This in turn causes the driver to
be automatically loaded on boot if VIC is the only enabled subdevice of
the logical host1x DRM device.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Upon system suspend, make sure the +5V HDMI regulator is disabled. This
avoids potentially leaking current to the HDMI connector. This also
makes sure that upon resume the regulator is enabled again, which in
some cases is necessary to properly restore the state of the supply on
resume.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The IOVA address for the cursor is the result of mapping the buffer
object for the given display controller. Make sure to use the proper
IOVA address as stored in the cursor's plane state.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
All the display related blocks on Tegra require contiguous memory. Using
the DMA API, there is no knowing at import time which device will end up
using the buffer, so it's not known whether or not an IOMMU will be used
to map the buffer.
Move the check for non-contiguous buffers/mappings to the tegra_dc_pin()
function which is now the earliest point where it is known if a DMA BUF
can be used by the given device or not.
v2: add check for contiguous buffer/mapping in tegra_dc_pin()
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Buffers that are imported from a DMA-BUF don't have pages allocated with
them. At the same time an SG table for them can't be derived using the
DMA API helpers because the necessary information doesn't exist. However
there's already an SG table that was created during import, so this can
simply be duplicated.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The Tegra DRM never actually took that lock, so the driver was broken
until generic locking was added in commit:
commit b962a12050a387e4bbf3a48745afe1d29d396b0d
Author: Rob Clark <robdclark@gmail.com>
Date: Mon Oct 22 14:31:22 2018 +0200
drm/atomic: integrate modeset lock with private objects
It's now no longer necessary to take that lock, so drop the check.
v2: add rationale for why it is now safe to drop the check (Daniel)
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Use the drm_panel_get_modes function.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: linux-tegra@vger.kernel.org
Link: https://patchwork.freedesktop.org/patch/msgid/20190804201637.1240-10-sam@ravnborg.org
|
|
No in-tree users left.
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Acked-by: Sumit Semwal <sumit.semwal@linaro.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: linux-tegra@vger.kernel.org
Link: https://patchwork.freedesktop.org/patch/msgid/20191118103536.17675-9-daniel.vetter@ffwll.ch
|
|
It doesn't have any callers anymore.
Aside: The ->mmap/munmap hooks have a bit a confusing name, they don't
do userspace mmaps, but a kernel vmap. I think most places use vmap
for this, except ttm, which uses kmap for vmap for added confusion.
mmap seems entirely for userspace mappings set up through mmap(2)
syscall.
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Acked-by: Sumit Semwal <sumit.semwal@linaro.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: linux-tegra@vger.kernel.org
Link: https://patchwork.freedesktop.org/patch/msgid/20191118103536.17675-3-daniel.vetter@ffwll.ch
|
|
Currently configurations can be generated where IOMMU_SUPPORT is
disabled but IOMMU_IOVA is built as a module and DRM_TEGRA as built-in.
In such a case, the symbols guarded by IOMMU_IOVA will not be available
when linking the Tegra DRM driver and cause a linking failure.
Simplify this by unconditionally selecting IOMMU_IOVA, which makes sure
that it will be forced to =y if DRM_TEGRA=y. Technically we can now get
IOMMU_IOVA code built-in even if we don't use it (Tegra DRM only uses it
when IOMMU_SUPPORT is also enabled), but such configuration are of a
mostly academic nature. In all practical configurations we want IOMMU
support anyway.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
If a client is already attached to an IOMMU domain that is not the
shared domain, don't try to attach it again. This allows using the
IOMMU-backed DMA API.
Since the IOMMU-backed DMA API is now supported and there's no way
to detach from it on 64-bit ARM, don't bother to detach from it on
32-bit ARM either.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
If a display controller is not attached to an explicit IOMMU domain,
which usually means that it's connected to an IOMMU domain controlled by
the DMA API, make sure to map the framebuffer to the display controller
address space. This allows us to transparently handle setups where the
display controller is attached to an IOMMU or setups where it isn't. It
also allows the driver to work with a DMA API that is backed by an
IOMMU.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Rename paddr -> iova and vaddr -> virt to make it clearer how these
addresses are used. This is important for a subsequent patch that makes
a distinction between the physical address (physical address of the
system memory from the CPU's point of view) and the IOVA (physical
address of the system memory from the device's point of view).
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Having to provide allocator hooks to the Falcon library is somewhat
cumbersome and it doesn't give the users of the library a lot of
flexibility to deal with allocations. Instead, remove the notion of
Falcon "operations" and let drivers deal with the memory allocations
themselves.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
If host1x_bo_pin() returns an SG table, create a DMA mapping for the
buffer. For buffers that the host1x client has already mapped itself,
host1x_bo_pin() returns NULL and the existing DMA address is used.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Add direction flags to host1x relocations performed during job pinning.
These flags indicate the kinds of accesses that hardware is allowed to
perform on the relocated buffers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The host1x_bo_pin() and host1x_bo_unpin() APIs are used to pin and unpin
buffers during host1x job submission. Pinning currently returns the SG
table and the DMA address (an IOVA if an IOMMU is used or a physical
address if no IOMMU is used) of the buffer. The DMA address is only used
for buffers that are relocated, whereas the host1x driver will map
gather buffers into its own IOVA space so that they can be processed by
the CDMA engine.
This approach has a couple of issues. On one hand it's not very useful
to return a DMA address for the buffer if host1x doesn't need it. On the
other hand, returning the SG table of the buffer is suboptimal because a
single SG table cannot be shared for multiple mappings, because the DMA
address is stored within the SG table, and the DMA address may be
different for different devices.
Subsequent patches will move the host1x driver over to the DMA API which
doesn't work with a single shared SG table. Fix this by returning a new
SG table each time a buffer is pinned. This allows the buffer to be
referenced by multiple jobs for different engines.
Change the prototypes of host1x_bo_pin() and host1x_bo_unpin() to take a
struct device *, specifying the device for which the buffer should be
pinned. This is required in order to be able to properly construct the
SG table. While at it, make host1x_bo_pin() return the SG table because
that allows us to return an ERR_PTR()-encoded error code if we need to,
or return NULL to signal that we don't need the SG table to be remapped
and can simply use the DMA address as-is. At the same time, returning
the DMA address is made optional because in the example of command
buffers, host1x doesn't need to know the DMA address since it will have
to create its own mapping anyway.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
All the devices that make up the DRM device are now part of the same
IOMMU group. This simplifies the handling of the IOMMU attachment and
also avoids exhausting the number of IOMMUs available on early Tegra
SoC generations.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The ->load() and ->unload() drivers are midlayers and should be avoided
in modern drivers. Fix this by moving the code into the driver ->probe()
and ->remove() implementations, respectively.
v2: kick out conflicting framebuffers before initializing fbdev
v3: rebase onto drm/tegra/for-next
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
In order to support different modes (DP in addition to HDMI), split out
the audio setup/teardown into callbacks.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The code to enable audio support is split into two parts, one being
generic for the SOR and another part that is specific whether the SOR is
in HDMI mode or in DP mode. Split out the common part in preparation for
reusing the code in DP mode.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
When the SOR is disabled in DP mode as part of an unplug event, do not
attempt to power the DP link down. Powering down the link requires the
DPAUX to transmit AUX messages which only works if there's a connected
sink.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The SOR0 on Tegra210 does, contrary to what was previously assumed, in
fact support DisplayPort. The difference between SOR0 and SOR1 is that
the latter supports audio and HDCP over DP, whereas the former doesn't.
The code for eDP and DP is now almost identical and the differences can
easily be parameterized based on the presence of a panel. There is no
need any longer to duplicate the code.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The correct I/O pad needs to be powered up before DP can be used. Make
sure the correct default is set for Tegra generations where the I/O pad
cannot be derived from the SOR instance.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
With the clocks modelled consistently across SoC generations, the clock
setup for eDP, HDMI and DP can now be unified.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Reuse parameters from earlier generations to support DisplayPort on
Tegra194.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The connector type detection code is duplicated in two places. Keeping
both places in sync is an extra maintenance burden that can be avoided
by comparing the connector type operations that are set upon the first
detection.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
So far the pad clock was only needed on the second SOR instance. The
clock does exist for all SOR instances, though, so make sure it is
always implemented. This prepares for further unification of the code
in subsequent patches.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The device tree bindings for the Tegra210 SOR don't require the
controller instance to be defined, since the instance can be derived
from the compatible string. The index is never used on Tegra210, so we
got away with it not getting set. However, subsequent patches will
change that, so make sure the proper index is used.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
It turns out that SOR1 is just another instance of the same block as the
SOR0, so there is no need to distinguish them.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Add support for regular DisplayPort on Tegra210 and Tegra186.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The SOR found on Tegra SoCs does not support all the rates potentially
advertised by eDP 1.4. Make sure that the rates that are not supported
are filtered out.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
Dave Airlie
Thierry Reding
Arnd Bergmann
Andrzej Pietrasiewicz
Daniel Vetter
Sam Ravnborg
Jani Nikula