| Age | Commit message (Collapse) | Author |
|---|
|
[ Upstream commit 9941b8129030c9202aaf39114477a0e58c0d6ffc ]
[Why]
In some scenario like 1366x768 VSR enabled connected with a 4K monitor
and playing 4K video in clone mode, underflow will be observed due to
decrease dppclk when previouse surface scan isn't finished
[How]
In this use case, surface flip is switching between 4K and 1366x768,
1366x768 needs smaller dppclk, and when decrease the clk and previous
surface scan is for 4K and scan isn't done, underflow will happen. Not
doing optimize bandwidth in case of flip pending.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e2d533eceb1feb0b8b965c3ff11184921532a28e ]
[why/how]
We found out that the register we read actually gets reset by SMU
after we loose power, meaning this always returns true
Signed-off-by: Joseph Gravenor <joseph.gravenor@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b6ef55ccba7ed00fc10e3e6f619c8f886162427f ]
[Why]
DP training sequence to set SCRAMBLING_DISABLE bit properly based on
training pattern - per DP Spec.
[How]
Update dpcd_pattern.v1_4.SCRAMBLING_DISABLE with 1 for TPS1, TPS2, TPS3,
but not for TPS4.
Signed-off-by: Vladimir Stempen <vladimir.stempen@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4e5183200d9b66695c754ef214933402056e7b95 ]
[Why]
If VUPDATE_END is before VUPDATE_START the delay calculated can become
very large, causing a soft hang.
[How]
Take the absolute value of the difference between START and END.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 31ecebee9c36d5e5e113a357a655d993fa916174 ]
[Why]
We dropped the delay after changed the cursor functions locking the
entire pipe to locking just the CURSOR registers to fix page flip
stuttering - this introduced cursor stuttering instead, and an underflow
issue.
The cursor update can be delayed indefinitely if the cursor update
repeatedly happens right around VUPDATE.
The underflow issue can happen if we do a viewport update on a pipe
on the same frame where a cursor update happens around VUPDATE - the
old cursor registers are retained which can be in an invalid position.
This can cause a pipe hang and indefinite underflow.
[How]
The complex, ideal solution to the problem would be a software
triple buffering mechanism from the DM layer to program only one cursor
update per frame just before VUPDATE.
The simple workaround until we have that infrastructure in place is
this change - bring back the delay until VUPDATE before locking, but
with some corrections to the calculations.
This didn't work for all timings before because the calculation for
VUPDATE was wrong - it was using the offset from VSTARTUP instead and
didn't correctly handle the case where VUPDATE could be in the back
porch.
Add a new hardware sequencer function to use the existing helper to
calculate the real VUPDATE start and VUPDATE end - VUPDATE can last
multiple lines after all.
Change the udelay to incorporate the width of VUPDATE as well.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b2a7b0ce0773bfa4406bc0a78e41979532a1edd7 ]
[Why]
Current locking scheme for cursor can result in a flip missing
its vsync, deferring it for one or more vsyncs. Result is a
potential for stuttering when cursor is moved.
[How]
Use cursor update lock so that flips are not blocked while cursor
is being programmed.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 009114f6df84150a567b05537aa29b9d660e419b ]
[Why]
Screen flickering when HDR switches between FP16 and ARGB2101010
[How]
Moved pipe_control_lock so stream update and plane update occur atomically
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Signed-off-by: Lucy Li <lucy.li@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit acdac228c4d1b9ff8ac778835719d3381c198aad ]
[Why]
DSC updates only set type to FULL UPDATE, but doesn't
flag the change
[How]
Add DSC flag update flag
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit bbf5f6c3f83bedd71006473849138a446ad4d9a3 ]
[Why]
Eventually want to lock at a higher level in stack.
To do this, we need to be able to isolate the parts that need to be done
after pipe unlock.
[How]
Split out programming that is done post unlock.
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f7d5991b92ff824798693ddf231cf814c9d5a88b ]
get_cursor_position already handles the case where the cursor has
negative off-screen coordinates by not setting
dc_cursor_position.enabled.
Signed-off-by: Simon Ser <contact@emersion.fr>
Fixes: 626bf90fe03f ("drm/amd/display: add basic atomic check for cursor plane")
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 650e723cecf2738dee828564396f3239829aba83 ]
[Why]
For MST case: when update_config is called to disable a stream,
this clears the settings for all the streams on that link.
We should only clear the settings for the stream that was disabled.
[How]
Clear the settings after the call to remove display is called.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Leo (Hanghong) Ma <hanghong.ma@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e6142dd511425cb827b5db869f489eb81f5f994d ]
[why]
During hotplug, a DP port may be connected to the sink through
passive adapter which does not support DPCD reads. Issuing reads
without checking for this condition will result in errors
[how]
Ensure the link is in aux_mode before initiating operation that result
in a DPCD read.
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 80797dd6f1a525d1160c463d6a9f9d29af182cbb ]
[Why]
Wait counter is not being reset for each pipe.
[How]
Move counter reset into pipe loop scope.
Signed-off-by: Roman Li <roman.li@amd.com>
Reviewed-by: Zhan Liu <Zhan.Liu@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 626bf90fe03fa080d8df06bb0397c95c53ae8e27 upstream.
This patch adds a basic cursor check when an atomic test-only commit is
performed. The position and size of the cursor plane is checked.
This should fix user-space relying on atomic checks to assign buffers to
planes.
Signed-off-by: Simon Ser <contact@emersion.fr>
Reported-by: Roman Gilg <subdiff@gmail.com>
References: https://github.com/emersion/libliftoff/issues/46
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Harry Wentland <hwentlan@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 668a6741f809f2d15d125cfe2b39661e8f1655ea ]
[WHY]
The downspread percentage was copied over from a previous version
of the display_mode_lib spreadsheet. This value has been updated,
and the previous value is too high to allow for such modes as
4K120hz. The new value is sufficient for such modes.
[HOW]
Update the value in dcn21_resource to match the spreadsheet.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit fdfd2a858590d318cfee483bd1c73e00f77533af ]
[Why]
Fixes the following scenario:
- Flip has been prepared sometime during the frame, update pending
- Cursor update happens right when VUPDATE would happen
- OPTC lock acquired, VUPDATE is blocked until next frame
- Flip is delayed potentially infinitely
With the igt@kms_cursor_legacy cursor-vs-flip-legacy test we can
observe nearly *13* frames of delay for some flips on Navi.
[How]
Apply the Raven workaround generically. When close enough to VUPDATE
block cursor updates from occurring from the dc_stream_set_cursor_*
helpers.
This could perhaps be a little smarter by checking if there were
pending updates or flips earlier in the frame on the HUBP side before
applying the delay, but this should be fine for now.
This fixes the kms_cursor_legacy test.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 3159d41db3a04330c31ece32f8b29752fc114848 ]
Check before programming the register since it isn't present on
all IPs using this code.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 718a5569b6fa6e1f49f1ae76a3c18acb4ddb74f1 ]
[Why]
When link loss happened, monitor can not light up if only re-train the
link.
[How]
Blank all the DP streams on this link before re-train the link, and then
unblank the stream
Signed-off-by: Xiaodong Yan <Xiaodong.Yan@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 59dfb0c64d3853d20dc84f4561f28d4f5a2ddc7d upstream.
The dcn20_validate_bandwidth function would have code touching the
incorrect registers emitted outside of the boundaries of the
DC_FP_START/END macros, at least on ppc64le. Work around the
problem by wrapping the whole function instead.
Signed-off-by: Daniel Kolesa <daniel@octaforge.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 5.6.x
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 87b7ebc2e16c14d32a912f18206a4d6cc9abc3e8 upstream.
[why]
We have seen a green screen after resume from suspend in a Raven system
connected with two displays (HDMI and DP) on X based system. We noticed
that this issue is related to bad DCC metadata from user space which may
generate hangs and consequently an underflow on HUBP. After taking a
deep look at the code path we realized that after resume we try to
restore the commit with the DCC enabled framebuffer but the framebuffer
is no longer valid.
[how]
This problem was only reported on Raven based system and after suspend,
for this reason, this commit adds a new parameter on
fill_plane_dcc_attributes() to give the option of disabling DCC
programmatically. In summary, for disabling DCC we first verify if is a
Raven system and if it is in suspend; if both conditions are true we
disable DCC temporarily, otherwise, it is enabled.
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1099
Co-developed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 3bae20137cae6c03f58f96c0bc9f3d46f0bc17d4 ]
[Why]
If a plane isn't being actively enabled or disabled then DC won't
always recalculate scaling rects and ratios for the primary plane.
This results in only a partial or corrupted rect being displayed on
the screen instead of scaling to fit the screen.
[How]
Add back the logic to recalculate the scaling rects into
dc_commit_updates_for_stream since this is the expected place to
do it in DC.
This was previously removed a few years ago to fix an underscan issue
but underscan is still functional now with this change - and it should
be, since this is only updating to the latest plane state getting passed
in.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 346d8a0a3c91888a412c2735d69daa09c00f0203 ]
[Why]
After v_total_min and max are updated in vrr structure, the changes are
not reflected in stream adjust. When these values are read from stream
adjust it does not reflect the actual state of the system.
[How]
Set stream adjust values equal to vrr adjust values after vrr adjust
values are updated.
Signed-off-by: Isabel Zhang <isabel.zhang@amd.com>
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c2850c125d919efbb3a9ab46410d23912934f585 ]
[Why]
When content type property is set to 1. We should enable hdcp2.2 and if we cant
then stop. Currently the way it works in DC is that if we fail hdcp2, we will
try hdcp1 after.
[How]
Use link config to force disable hdcp1.4 when type1 is set.
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 72f5b5a308c744573fdbc6c78202c52196d2c162 upstream.
[WHY]
In cases where a clock table is malformed such that fclk entries have
frequencies but not voltages listed, we don't catch the error and set
clocks to 0 instead of using hardcoded values as we should.
[HOW]
Add check for clock tables fclk entry's voltage as well
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit '16f17eda8bad ("drm/amd/display: Send vblank and user
events at vsartup for DCN")' introduces a new way of pageflip
completion handling for DCN, and some trouble.
The current implementation introduces a race condition, which
can cause pageflip completion events to be sent out one vblank
too early, thereby confusing userspace and causing flicker:
prepare_flip_isr():
1. Pageflip programming takes the ddev->event_lock.
2. Sets acrtc->pflip_status == AMDGPU_FLIP_SUBMITTED
3. Releases ddev->event_lock.
--> Deadline for surface address regs double-buffering passes on
target pipe.
4. dc_commit_updates_for_stream() MMIO programs the new pageflip
into hw, but too late for current vblank.
=> pflip_status == AMDGPU_FLIP_SUBMITTED, but flip won't complete
in current vblank due to missing the double-buffering deadline
by a tiny bit.
5. VSTARTUP trigger point in vblank is reached, VSTARTUP irq fires,
dm_dcn_crtc_high_irq() gets called.
6. Detects pflip_status == AMDGPU_FLIP_SUBMITTED and assumes the
pageflip has been completed/will complete in this vblank and
sends out pageflip completion event to userspace and resets
pflip_status = AMDGPU_FLIP_NONE.
=> Flip completion event sent out one vblank too early.
This behaviour has been observed during my testing with measurement
hardware a couple of time.
The commit message says that the extra flip event code was added to
dm_dcn_crtc_high_irq() to prevent missing to send out pageflip events
in case the pflip irq doesn't fire, because the "DCH HUBP" component
is clock gated and doesn't fire pflip irqs in that state. Also that
this clock gating may happen if no planes are active. This suggests
that the problem addressed by that commit can't happen if planes
are active.
The proposed solution is therefore to only execute the extra pflip
completion code iff the count of active planes is zero and otherwise
leave pflip completion handling to the pflip irq handler, for a
more race-free experience.
Note that i don't know if this fixes the problem the original commit
tried to address, as i don't know what the test scenario was. It
does fix the observed too early pageflip events though and points
out the problem introduced.
Fixes: 16f17eda8bad ("drm/amd/display: Send vblank and user events at vsartup for DCN")
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
This fixes a problem found on the MacBookPro 2017 Retina panel:
The panel reports 10 bpc color depth in its EDID, and the
firmware chooses link settings at boot which support enough
bandwidth for 10 bpc (324000 kbit/sec aka LINK_RATE_RBR2
aka 0xc), but the DP_MAX_LINK_RATE dpcd register only reports
2.7 Gbps (multiplier value 0xa) as possible, in direct
contradiction of what the firmware successfully set up.
This restricts the panel to 8 bpc, not providing the full
color depth of the panel on Linux <= 5.5. Additionally, commit
'4a8ca46bae8a ("drm/amd/display: Default max bpc to 16 for eDP")'
introduced into Linux 5.6-rc1 will unclamp panel depth to
its full 10 bpc, thereby requiring a eDP bandwidth for all
modes that exceeds the bandwidth available and causes all modes
to fail validation -> No modes for the laptop panel -> failure
to set any mode -> Panel goes dark.
This patch adds a quirk specific to the MBP 2017 15" Retina
panel to override reported max link rate to the correct maximum
of 0xc = LINK_RATE_RBR2 to fix the darkness and reduced display
precision.
Please apply for Linux 5.6+ to avoid regressing Apple MBP panel
support.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
In dcn20_funcs and dcn21_funcs struct, the member ".dsc_pg_control = NULL"
should be removed due to .dsc_pg_control be assigned to dcn20_dsc_pg_control.
Signed-off-by: Stanley.Yang <Stanley.Yang@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[why]
nv14 previously inherited soc bb from generic dcn 2, did not match
watermark values according to memory team
[how]
add nv14 specific soc bb: copy nv2 generic that it was
using from before, but changed num channels to 8
Signed-off-by: Martin Leung <martin.leung@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
from s3 (v2)
This interface is for dGPU Navi1x. Linux dc-pplib interface depends
on window driver dc implementation.
For Navi1x, clock settings of dcn watermarks are fixed. the settings
should be passed to smu during boot up and resume from s3.
boot up: dc calculate dcn watermark clock settings within dc_create,
dcn20_resource_construct, then call pplib functions below to pass
the settings to smu:
smu_set_watermarks_for_clock_ranges
smu_set_watermarks_table
navi10_set_watermarks_table
smu_write_watermarks_table
For Renoir, clock settings of dcn watermark are also fixed values.
dc has implemented different flow for window driver:
dc_hardware_init / dc_set_power_state
dcn10_init_hw
notify_wm_ranges
set_wm_ranges
For Linux
smu_set_watermarks_for_clock_ranges
renoir_set_watermarks_table
smu_write_watermarks_table
dc_hardware_init -> amdgpu_dm_init
dc_set_power_state --> dm_resume
therefore, linux dc-pplib interface of navi10/12/14 is different
from that of Renoir.
v2: add missing unlock in error case
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Swath sizes are being calculated incorrectly. The horizontal swath size
should be the product of block height, viewport width, and bytes per
element, but the calculation uses viewport height instead of width. The
vertical swath size is similarly incorrectly calculated. The effect of
this is that we report the wrong DCC caps.
[How]
Use viewport width in the horizontal swath size calculation and viewport
height in the vertical swath size calculation.
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
If we have a single MST display and we disconnect it, we dont disable that
link. This causes the old link settings to still exist
Now on a replug for MST we think its a link loss and will try to reallocate
mst payload which will fail, throwing warning below.
[ 129.374192] [drm] Failed to updateMST allocation table forpipe idx:0
[ 129.374206] ------------[ cut here ]------------
[ 129.374284] WARNING: CPU: 14 PID: 1710 at
drivers/gpu/drm/amd/amdgpu/../dal-dev/dc/core/dc_link.c:3153
dc_link_allocate_mst_payload+0x1f7/0x220 [amdgpu]
[ 129.374285] Modules linked in: amdgpu(OE) amd_iommu_v2 gpu_sched ttm
drm_kms_helper drm fb_sys_fops syscopyarea sysfillrect sysimgblt
binfmt_misc nls_iso8859_1 edac_mce_amd snd_hda_codec_realtek
snd_hda_codec_generic ledtrig_audio kvm snd_hda_codec_hdmi snd_hda_intel
snd_intel_nhlt snd_hda_codec irqbypass snd_hda_core snd_hwdep snd_pcm
snd_seq_midi snd_seq_midi_event snd_rawmidi crct10dif_pclmul snd_seq
crc32_pclmul ghash_clmulni_intel snd_seq_device snd_timer snd aesni_intel
eeepc_wmi crypto_simd asus_wmi joydev cryptd sparse_keymap input_leds
soundcore video glue_helper wmi_bmof mxm_wmi k10temp ccp mac_hid
sch_fq_codel parport_pc ppdev lp parport ip_tables x_tables autofs4
hid_generic usbhid hid igb i2c_algo_bit ahci dca i2c_piix4 libahci
gpio_amdpt wmi gpio_generic
[ 129.374318] CPU: 14 PID: 1710 Comm: kworker/14:2 Tainted: G W OE 5.4.0-rc7bhawan+ #480
[ 129.374318] Hardware name: System manufacturer System Product Name/PRIME X370-PRO, BIOS 0515 03/30/2017
[ 129.374397] Workqueue: events dm_irq_work_func [amdgpu]
[ 129.374468] RIP: 0010:dc_link_allocate_mst_payload+0x1f7/0x220 [amdgpu]
[ 129.374470] Code: 52 20 e8 1c 63 ad f4 48 8b 5d d0 65 48 33 1c 25 28 00
00 00 b8 01 00 00 00 75 16 48 8d 65 d8 5b 41 5c 41 5d 41 5e 41 5f 5d c3
<0f> 0b e9 fa fe ff ff e8 ed 5b d6 f3 41 0f b6 b6 c4 02 00 00 48 c7
[ 129.374471] RSP: 0018:ffff9f9141e7fcc0 EFLAGS: 00010246
[ 129.374472] RAX: 0000000000000000 RBX: ffff91ef0762f800 RCX: 0000000000000000
[ 129.374473] RDX: 0000000000000005 RSI: ffffffffc0c4a988 RDI: 0000000000000004
[ 129.374474] RBP: ffff9f9141e7fd10 R08: 0000000000000005 R09: 0000000000000000
[ 129.374475] R10: 0000000000000002 R11: 0000000000000001 R12: ffff91eebd510c00
[ 129.374475] R13: ffff91eebd510e58 R14: ffff91ef052c01b8 R15: 0000000000000006
[ 129.374476] FS: 0000000000000000(0000) GS:ffff91ef0ef80000(0000) knlGS:0000000000000000
[ 129.374477] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 129.374478] CR2: 000055623ea01d50 CR3: 0000000408a8c000 CR4: 00000000003406e0
[ 129.374479] Call Trace:
[ 129.374550] dc_link_reallocate_mst_payload+0x12e/0x150 [amdgpu]
[ 129.374617] dc_link_handle_hpd_rx_irq+0x6d4/0x6e0 [amdgpu]
[ 129.374693] handle_hpd_rx_irq+0x77/0x310 [amdgpu]
[ 129.374768] dm_irq_work_func+0x53/0x70 [amdgpu]
[ 129.374774] process_one_work+0x1fd/0x3f0
[ 129.374776] worker_thread+0x255/0x410
[ 129.374778] kthread+0x121/0x140
[ 129.374780] ? process_one_work+0x3f0/0x3f0
[ 129.374781] ? kthread_park+0x90/0x90
[ 129.374785] ret_from_fork+0x22/0x40
[How]
when we disable MST we should clear the cur link settings (lane_count=0 is
good enough). This will cause us to not reallocate payloads earlier than
expected and not throw the warning
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Use the existence of the workqueue itself to determine when to
enable HDCP features rather than sprinkling asic checks all over
the code. Also add a check for the existence of the hdcp
workqueue in the irq handling on the off chance we get and HPD
RX interrupt with the CP bit set. This avoids a crash if
the driver doesn't support HDCP for a particular asic.
Fixes: 96a3b32e67236f ("drm/amd/display: only enable HDCP for DCN+")
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=206519
Reviewed-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
We were using incorrect byte order after we started using the drm_defines
So fix it.
Fixes: 02837a91ae75 ("drm/amd/display: add and use defines from drm_hdcp.h")
Signed-off-by: JinZe.Xu <JinZe.Xu@amd.com>
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[WHY]
Programming DPPCLK to the same value currently set may cause
underflow while playing video in certain conditions.
[HOW]
Only program DPPCLK if clock is not the same as the
previous value programmed.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
In DCN hardware sequencer we do actually call ATOM_INIT correctly per
pipe. The workaround is not necessary for command table offloading.
[How]
Drop the workaround since it's not needed.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
On PowerPC, the compiler will tag object files with whether they
use hard or soft float FP ABI and whether they use 64 or 128-bit
long double ABI. On systems with 64-bit long double ABI, a tag
will get emitted whenever a double is used, as on those systems
a long double is the same as a double. This will prevent linkage
as other files are being compiled with hard-float.
On ppc64, this code will never actually get used for the time
being, as the only currently existing hardware using it are the
Renoir APUs. Therefore, until this is testable and can be fixed
properly, at least make sure the build will not fail.
Signed-off-by: Daniel Kolesa <daniel@octaforge.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Starting from 14nm, the PLL is built into the PHY and the PLL is mapped
to PHY on 1 to 1 basis. In the code, the DP port is mapped to a PLL that was not
initialized. This causes DP to HDMI dongle to not light up the display.
[How]
Initializations added for PLL2 when creating resources.
Signed-off-by: Isabel Zhang <isabel.zhang@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Underflow is observed when plug in a 4K@60 monitor with
1366x768 eDP due to DPPCLK is too low.
[How]
Limit minimum DPPCLK to 100MHz.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Engine can be NULL in some cases, so we must not acquire it.
[How]
Check for NULL engine before acquiring.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[WHY & HOW]
Previously drain clk was unconstrained and fill clk was constrained on fclk.
We want to change it to fill clk unconstrained and drain clock constrained
to dcfclk.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[WHY]
The optimized_require flag is needed to set watermarks and clocks lower
in certain conditions. This flag is set to true and then set to false
while programming front end in dcn20.
[HOW]
Do not set the flag to false while disabling plane.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Driver crash with psr feature enabled due to divide-by-zero error.
This is a regression after rework to calculate static screen frame
number entry time.
[How]
Correct order of operations to avoid divide-by-zero.
Signed-off-by: Roman Li <roman.li@amd.com>
Reviewed-by: Zhan Liu <Zhan.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Disabling a display on MST can potentially happen after the entire MST
topology has been removed, which means that we can't communicate with
the topology at all in this scenario. Likewise, this also means that we
can't properly update payloads on the topology and as such, it's a good
idea to ignore payload update failures when disabling displays.
Currently, amdgpu makes the mistake of halting the payload update
process when any payload update failures occur, resulting in leaving
DC's local copies of the payload tables out of date.
This ends up causing problems with hotplugging MST topologies, and
causes modesets on the second hotplug to fail like so:
[drm] Failed to updateMST allocation table forpipe idx:1
------------[ cut here ]------------
WARNING: CPU: 5 PID: 1511 at
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc_link.c:2677
update_mst_stream_alloc_table+0x11e/0x130 [amdgpu]
Modules linked in: cdc_ether usbnet fuse xt_conntrack nf_conntrack
nf_defrag_ipv6 libcrc32c nf_defrag_ipv4 ipt_REJECT nf_reject_ipv4
nft_counter nft_compat nf_tables nfnetlink tun bridge stp llc sunrpc
vfat fat wmi_bmof uvcvideo snd_hda_codec_realtek snd_hda_codec_generic
snd_hda_codec_hdmi videobuf2_vmalloc snd_hda_intel videobuf2_memops
videobuf2_v4l2 snd_intel_dspcfg videobuf2_common crct10dif_pclmul
snd_hda_codec videodev crc32_pclmul snd_hwdep snd_hda_core
ghash_clmulni_intel snd_seq mc joydev pcspkr snd_seq_device snd_pcm
sp5100_tco k10temp i2c_piix4 snd_timer thinkpad_acpi ledtrig_audio snd
wmi soundcore video i2c_scmi acpi_cpufreq ip_tables amdgpu(O)
rtsx_pci_sdmmc amd_iommu_v2 gpu_sched mmc_core i2c_algo_bit ttm
drm_kms_helper syscopyarea sysfillrect sysimgblt fb_sys_fops cec drm
crc32c_intel serio_raw hid_multitouch r8152 mii nvme r8169 nvme_core
rtsx_pci pinctrl_amd
CPU: 5 PID: 1511 Comm: gnome-shell Tainted: G O 5.5.0-rc7Lyude-Test+ #4
Hardware name: LENOVO FA495SIT26/FA495SIT26, BIOS R12ET22W(0.22 ) 01/31/2019
RIP: 0010:update_mst_stream_alloc_table+0x11e/0x130 [amdgpu]
Code: 28 00 00 00 75 2b 48 8d 65 e0 5b 41 5c 41 5d 41 5e 5d c3 0f b6 06
49 89 1c 24 41 88 44 24 08 0f b6 46 01 41 88 44 24 09 eb 93 <0f> 0b e9
2f ff ff ff e8 a6 82 a3 c2 66 0f 1f 44 00 00 0f 1f 44 00
RSP: 0018:ffffac428127f5b0 EFLAGS: 00010202
RAX: 0000000000000002 RBX: ffff8d1e166eee80 RCX: 0000000000000000
RDX: ffffac428127f668 RSI: ffff8d1e166eee80 RDI: ffffac428127f610
RBP: ffffac428127f640 R08: ffffffffc03d94a8 R09: 0000000000000000
R10: ffff8d1e24b02000 R11: ffffac428127f5b0 R12: ffff8d1e1b83d000
R13: ffff8d1e1bea0b08 R14: 0000000000000002 R15: 0000000000000002
FS: 00007fab23ffcd80(0000) GS:ffff8d1e28b40000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f151f1711e8 CR3: 00000005997c0000 CR4: 00000000003406e0
Call Trace:
? mutex_lock+0xe/0x30
dc_link_allocate_mst_payload+0x9a/0x210 [amdgpu]
? dm_read_reg_func+0x39/0xb0 [amdgpu]
? core_link_enable_stream+0x656/0x730 [amdgpu]
core_link_enable_stream+0x656/0x730 [amdgpu]
dce110_apply_ctx_to_hw+0x58e/0x5d0 [amdgpu]
? dcn10_verify_allow_pstate_change_high+0x1d/0x280 [amdgpu]
? dcn10_wait_for_mpcc_disconnect+0x3c/0x130 [amdgpu]
dc_commit_state+0x292/0x770 [amdgpu]
? add_timer+0x101/0x1f0
? ttm_bo_put+0x1a1/0x2f0 [ttm]
amdgpu_dm_atomic_commit_tail+0xb59/0x1ff0 [amdgpu]
? amdgpu_move_blit.constprop.0+0xb8/0x1f0 [amdgpu]
? amdgpu_bo_move+0x16d/0x2b0 [amdgpu]
? ttm_bo_handle_move_mem+0x118/0x570 [ttm]
? ttm_bo_validate+0x134/0x150 [ttm]
? dm_plane_helper_prepare_fb+0x1b9/0x2a0 [amdgpu]
? _cond_resched+0x15/0x30
? wait_for_completion_timeout+0x38/0x160
? _cond_resched+0x15/0x30
? wait_for_completion_interruptible+0x33/0x190
commit_tail+0x94/0x130 [drm_kms_helper]
drm_atomic_helper_commit+0x113/0x140 [drm_kms_helper]
drm_atomic_helper_set_config+0x70/0xb0 [drm_kms_helper]
drm_mode_setcrtc+0x194/0x6a0 [drm]
? _cond_resched+0x15/0x30
? mutex_lock+0xe/0x30
? drm_mode_getcrtc+0x180/0x180 [drm]
drm_ioctl_kernel+0xaa/0xf0 [drm]
drm_ioctl+0x208/0x390 [drm]
? drm_mode_getcrtc+0x180/0x180 [drm]
amdgpu_drm_ioctl+0x49/0x80 [amdgpu]
do_vfs_ioctl+0x458/0x6d0
ksys_ioctl+0x5e/0x90
__x64_sys_ioctl+0x16/0x20
do_syscall_64+0x55/0x1b0
entry_SYSCALL_64_after_hwframe+0x44/0xa9
RIP: 0033:0x7fab2121f87b
Code: 0f 1e fa 48 8b 05 0d 96 2c 00 64 c7 00 26 00 00 00 48 c7 c0 ff ff
ff ff c3 66 0f 1f 44 00 00 f3 0f 1e fa b8 10 00 00 00 0f 05 <48> 3d 01
f0 ff ff 73 01 c3 48 8b 0d dd 95 2c 00 f7 d8 64 89 01 48
RSP: 002b:00007ffd045f9068 EFLAGS: 00000246 ORIG_RAX: 0000000000000010
RAX: ffffffffffffffda RBX: 00007ffd045f90a0 RCX: 00007fab2121f87b
RDX: 00007ffd045f90a0 RSI: 00000000c06864a2 RDI: 000000000000000b
RBP: 00007ffd045f90a0 R08: 0000000000000000 R09: 000055dbd2985d10
R10: 000055dbd2196280 R11: 0000000000000246 R12: 00000000c06864a2
R13: 000000000000000b R14: 0000000000000000 R15: 000055dbd2196280
---[ end trace 6ea888c24d2059cd ]---
Note as well, I have only been able to reproduce this on setups with 2
MST displays.
Changes since v1:
* Don't return false when part 1 or part 2 of updating the payloads
fails, we don't want to abort at any step of the process even if
things fail
Reviewed-by: Mikita Lipski <Mikita.Lipski@amd.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
We might get different numbers of clocks from powerplay depending
on what the OEM has populated.
v2: add assert for at least one level
Bug: https://gitlab.freedesktop.org/drm/amd/issues/963
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
When we disable a connector we don't explicitly remove it from the module so the
display is still cached(SW) in the hdcp_module.
SST: no issues because we can only have 1 display per link
MST: We have x displays per link, now if we disable 1 we don't remove it from the
module so the module has x display cached(SW).
If we try to enable HDCP, psp verification will fail because we are reporting x
displays while the HW only has x-1 display enabled
[How]
Check the callback for when we disable stream and call remove display.
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[why]
Remove a backslash symbol accidentally left in increase bpp function
when computing mst dsc configuration.
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Reviewed-by: Zhan Liu <zhan.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
In current code we're essentially drawing the cursor on every pipe
that contains it. This only works when the planes have the same
scaling for src to dest rect, otherwise we'll get "double cursor" where
one cursor is incorrectly filtered and offset from the real position.
[How]
Without dedicated cursor planes on DCN we require at least one pipe
that matches the scaling of the current timing.
This is an optimization and workaround for the most common case where
the top-most plane is not scaled but the bottom-most plane is scaled.
Whenever a pipe has a parent pipe in the blending tree whose recout
fully contains the current pipe we can disable the pipe.
This only applies when the pipe is actually visible of course.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
dc_validate_global_state()
[Why]
Need to do atomic check first, then validate global state.
If not, when connecting both MST and HDMI displays and
set a bad mode via xrandr, system will hang.
[How]
Move drm_dp_mst_atomic_check() to the front of
dc_validate_global_state().
Signed-off-by: Zhan Liu <zhan.liu@amd.com>
Reviewed-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
link_integrity_check
There is a spelling mistake on the struct field name link_integiry_check,
fix this by renaming it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
A for-loop is iterating from 0 up to 1000 however the loop variable count
is a u8 and hence not large enough. Fix this by making count an int.
Also remove the redundant initialization of count since this is never used
and add { } on the loop statement make the loop block clearer.
v2: drop useless else (Walter Harms)
Addresses-Coverity: ("Operands don't affect result")
Fixes: ed581a0ace44 ("drm/amd/display: wait for update when setting dpg test pattern")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
Yongqiang Sun
Joseph Gravenor
Vladimir Stempen
Aric Cyr
Nicholas Kazlauskas
Anthony Koo
Simon Ser
Leo (Hanghong) Ma
Aurabindo Pillai
Roman Li
Sung Lee
Dmytro Laktyushkin
Xiaodong Yan
Daniel Kolesa
Rodrigo Siqueira
Isabel Zhang
Bhawanpreet Lakha
Michael Strauss
Mario Kleiner
Stanley.Yang
Martin Leung
Hersen Wu
Josip Pavic
Alex Deucher
Lyude Paul
Mikita Lipski
Zhan Liu
Colin Ian King