| Age | Commit message (Collapse) | Author |
|---|
|
Fix manual trigger source correctly be TRIGA for DCN2
rather than MANUAL_FLOW.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[why]
Up to 4 ODM memory pieces are required per ODM combine and cannot
overlap, i.e. each ODM "session" has to use its own memory pieces.
The ODM-memory mapping is currently broken for generic case.
The maximum number of memory pieces is ASIC-dependent, but it's always
big enough to satisfy maximum number of ODM combines. Memory pieces
are mapped as a bit-map, i.e. one memory piece corresponds to one bit.
The OPTC doing ODM needs to select memory pieces by setting the
corresponding bits, making sure there's no overlap with other OPTC
instances that might be doing ODM.
The current mapping works only for OPTC instance indexes smaller than
3. For instance indexes 3 and up it practically maps no ODM memory,
causing black, gray or white screen in display configs that include
ODM on OPTC instance 3 or up.
[how]
Statically map two unique ODM memory pieces for each OPTC instance
and piece them together when programming ODM combine mode.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
To quickly validate whether DMCUB is running and accepting commands for
offload testing we want to intercept a common sequence as part of
modeset programming.
[How]
OTG enable will cause the most impact in terms of golden register
changes and it's a single register write.
This approach was previously done in dcn10 code when it was shared with
dcn20 but it wasn't ported over to the dcn20 code.
Port over start, execute and wait sequence into dcn20_optc.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
It is becoming increasingly hard to figure out which
function is called on the different DCN versions
[How]
1. Make function pointer table init in its own init.c file
2. Remove other scenarios in hwseq.c file that need to
include headers of other DCN versions. (If needed,
it should have been done via the function pointers)
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
DCN2 and DSC are stable enough to be build by default. So drop the flags.
[How]
Remove them using the unifdef tool. The following commands were executed
in sequence:
$ find -name '*.c' -exec unifdef -m -DCONFIG_DRM_AMD_DC_DSC_SUPPORT -DCONFIG_DRM_AMD_DC_DCN2_0 -UCONFIG_TRIM_DRM_AMD_DC_DCN2_0 '{}' ';'
$ find -name '*.h' -exec unifdef -m -DCONFIG_DRM_AMD_DC_DSC_SUPPORT -DCONFIG_DRM_AMD_DC_DCN2_0 -UCONFIG_TRIM_DRM_AMD_DC_DCN2_0 '{}' ';'
In addition:
* Remove from kconfig, and replace any dependencies with DCN1_0.
* Remove from any makefiles.
* Fix and cleanup NV defninitions in dal_asic_id.h
* Expand DCN1 ifdef to include DCN2 code in the following files:
* clk_mgr/clk_mgr.c: dc_clk_mgr_create()
* core/dc_resources.c: dc_create_resource_pool()
* dce/dce_dmcu.c: dcn20_*lock_phy()
* dce/dce_dmcu.c: dcn20_funcs
* dce/dce_dmcu.c: dcn20_dmcu_create()
* gpio/hw_factory.c: dal_hw_factory_init()
* gpio/hw_translate.c: dal_hw_translate_init()
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[why]
we found using an active DP to HDMI panel that we weren't validating
dp_pixel_format and hardware timing v_front_porch, causing screen to
blank and/or corrupt while attempting a seamless boot.
[how]
added checks during dc_validate_seamless_boot_timing for these values
Signed-off-by: Martin Leung <martin.leung@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[why]
Some ODM-related register settings are inconsistently updated by VBIOS, causing
the state in DC to be invalid, which would then end up crashing in certain
use-cases (such as disable/enable device).
[how]
Check the enabled status of the second pipe when determining the number of
OPTC sources. If the second pipe is disabled, set the number of sources to 1
regardless of other settings (that may not be updated correctly).
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
This reverts commit 6c5be4ac630805d3a3b20157a0c6421ef815fe78.
This commit was accidentally promoted twice
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
This reverts commit 9e14d4f17e23ce46d346a6a22a295b4a65b9d918.
optc dsc config was causing warnings due to missing register
definitions. With the registers restored, the function can
be re-enabled
The reverted commit also disabled sanity checks and dsc
power gating. The sanity check warnings are not associated
with dsc, and power gating on dsc still has an issue on
non-dsc monitors where the dsc hardware block is never init
and so cannot respond to power gating requests. Therefore,
those are left as is
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Current optc odm interface only accepts 2 opps, we need to
expand this to allow 4 to 1 odm combine.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Seamless boot (building SW state inheriting BIOS-initialized timing) was
enabled on DCN2, including fixes
[How]
Includes fixes for MPC, DPPCLK, and DIG FE mapping/OTG source select/
Pixel clock.
This is part 2 of 2 for seamless boot NV10
Signed-off-by: Martin Leung <martin.leung@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Some display's hsync width is lower than the minimum dcn20 is set
to support right now. This will cause optc1_validate_timing to fail which
eventually will result in wrong set mode. This was set to 8 as per
HW team's request for no valid reason.
[How]
Changing min_h_sync_width to 4 will let us validate timing for
preffered mode and light up the headset. This change was made
to Vega 10 before for a similar issue.
Signed-off-by: Fatemeh Darbehani <fatemeh.darbehani@amd.com>
Reviewed-by: Joshua Aberback <Joshua.Aberback@amd.com>
Acked-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[why]
If a set is done, DSC settings are zeroed out, leading to no DSC for the modes
that require ODM, such as 8k60.
This was a regression introduced by 5a4f26295176bbfc776c75aaf0f6dd8ccf806958.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
OPTC data format was left at its default value (444) when enabling
ODM combine. This caused issues with FPGA capture.
[How]
Write the OPTC_DATA_FORMAT field when enabling ODM combine.
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[why]
when an update programming sequence requires both
front end and back end pipe to be updated synchronously,
a global update lock needs to be set to ensure that
we don't get a frame with only front end update but
not the back end update.
[how]
setup global lock parameters on enable_stream_timing.
enable global lock when pipe_control_lock_global is called.
disable global lock when pipe_control_lock is called.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[why]
Global optic double buffer lock is currently disabled due to
incorrect programming sequence that affects non global lock.
[how]
Isolate global lock programming sequence out of non global lock
programming sequence, so it can be enabled without affecting
non global lock.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[why] we meet a bug when program dsc register even dsc mode is not
enabled. disable dsc config for now. we will re-visit this issue.
Signed-off-by: hersen wu <hersenxs.wu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
In the previous implementation DRR event sometimes came
in during FP2 region which is a keep-out zone. This
would cause the frame not to latch until the next frame
which resulted in heavy flicker. To fix this we need
to make sure that it triggers in the BP.
[How]
1. Remove DRR programming during flip
2. Setup manual trigger for DRR event and trigger it
after surface programming is complete
Signed-off-by: Eryk Brol <eryk.brol@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
VTG has a parameter FP2, which is defined as:
if VSTARTUP is before VSYNC:
FP2 = number of lines in between VSTARTUP and VSYNC
else
FP2 = 0
Currently, FP2 is only programmed during "program_timing". However, the
position of VSTARTUP is affected by the prefetching requirements on all pipes,
so the position might change when we do memory request control on another pipe, so we need
to make sure that FP2 stays up-to-date whenever we adjust VSTARTUP.
[How]
- refactor VTG_CONTROL programming into a new function "set_vtg_params"
- call it after calling "program_global_sync"
- make sure it's called after because it relies on the cached dlg params
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Jun Lei <Jun.Lei@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Add support for DCN2 DSC (Display Stream Compression)
HW Blocks:
+--------++------+ +----------+
| HUBBUB || HUBP | <-- | MMHUBBUB |
+--------++------+ +----------+
| ^
v |
+--------+ +--------+
| DPP | | DWB |
+--------+ +--------+
|
v ^
+--------+ |
| MPC | |
+--------+ |
| |
v |
+-------+ +-------+ |
| OPP | <--> | DSC | |
+-------+ +-------+ |
| |
v |
+--------+ /
| OPTC | --------------
+--------+
|
v
+--------+ +--------+
| DIO | | DCCG |
+--------+ +--------+
v2: rebase (Alex)
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Add support for programming the DCN2 OPTC (Output Timing Controller)
HW Blocks:
+--------+
| OPTC |
+--------+
|
v
+--------+ +--------+
| DIO | | DCCG |
+--------+ +--------+
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
Aric Cyr
Nikola Cornij
Nicholas Kazlauskas
Anthony Koo
Bhawanpreet Lakha
Martin Leung
David Francis
Dmytro Laktyushkin
Fatemeh Darbehani
Ilya Bakoulin
Wenjing Liu
hersen wu
Eryk Brol
Joshua Aberback
Harry Wentland