| Age | Commit message (Collapse) | Author |
|---|
|
Make sure to free any hogged gpios on errors in gpiochip_add.
Also move all forward declarations to the top of the file.
Fixes: f625d4601759 ("gpio: add GPIO hogging mechanism")
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Move irq trigger flags, which as sysfs-interface specific, to the class
device data.
This avoids accessing the gpio-descriptor flags field using non-atomic
operations without any locking, and allows for a more clear separation
of the sysfs interface from gpiolib core.
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Remove FLAG_SYSFS_DIR, which is sysfs-interface specific, and store it
in the class-device data instead.
Note that the flag is only used during export.
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Rename active-low helper using common prefix.
Also remove unnecessary manipulation of value argument.
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Make sure to deregister the class device (and release the irq) while
holding the sysfs lock in gpio_unexport to prevent racing with
gpio_export.
Note that this requires the recently introduced per-gpio locking to
avoid a deadlock with the kernfs active protection when waiting for the
attribute operations to drain during deregistration.
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add a per-gpio mutex to serialise attribute operations rather than use
one global mutex for all gpios and chips.
Having a single global lock for all gpios in a system adds unnecessary
latency to the sysfs interface, and especially when having gpio
controllers connected over slow buses.
Now that the global gpio-sysfs interrupt table is gone and with per-gpio
data in place, we can easily switch to using a more fine-grained locking
scheme.
Keep the global mutex to serialise the global (class) operations of gpio
export and unexport and chip removal.
Also document the locking assumptions made.
Note that this is also needed to fix a race between gpiod_export and
gpiod_unexport.
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Drop unnecessary locking from gpiod_export_link. If the class device has
not already been unregistered, class_find_device returns the ref-counted
class device so there's no need for locking.
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Remove goto from success path.
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add separate helper functions for irq request and free.
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Only call irq helper if actually reconfiguring interrupt state.
This is a preparatory step in introducing separate gpio-irq request and
free functions.
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Store the value sysfs entry in the gpiod data rather than in a global
table accessed through an index stored in the overloaded gpio-descriptor
flag field.
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Remove redundant gpio-descriptor parameters from sysfs_set_active_low and
gpio_setup_irq.
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add gpiod class-device data.
This is a first step in getting rid of the insane gpio-descriptor flag
overloading, backward irq-interface implementation, and course grained
sysfs-interface locking (a single static mutex for every operation on
all exported gpios in a system).
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The attribute operations will never be called for an unregistered device
so remove redundant checks for FLAG_EXPORT.
Note that kernfs will also guarantee that any active sysfs operation has
finished before the attribute is removed during deregistration.
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Make sure to release any irq only after the class device has been
deregistered.
This avoids a race between gpiod_unexport and edge_store, where an irq
could be allocated just before the gpio class device is deregistered
without relying on FLAG_EXPORT and the global sysfs lock.
Note that there is no need to hold the sysfs lock when releasing the irq
after the class device is gone as kernfs will prevent further attribute
operations.
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Use DEVICE_ATTR_RO and DEVICE_ATTR_RW rather than specifying masks and
callbacks directly.
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Remove gpiod_sysfs_set_active_low (and gpio_sysfs_set_active_low) which
allowed code to change the polarity of a gpio line even after it had
been exported through sysfs.
Drivers should not care, and generally does not know, about gpio-line
polarity which is a hardware feature that needs to be described by
firmware.
It is currently possible to define gpio-line polarity in device-tree and
acpi firmware or using platform data. Userspace can also change the
polarity through sysfs.
Note that drivers using the legacy gpio interface could still use
GPIOF_ACTIVE_LOW to change the polarity before exporting the gpio.
There are no in-kernel users of this interface.
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Harry Wei <harryxiyou@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: linux-doc@vger.kernel.org
Cc: linux-kernel@zh-kernel.org
Cc: linux-arch@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Rename the gpio-chip export/unexport functions to the more descriptive
names gpiochip_sysfs_register and gpiochip_sysfs_unregister.
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Clean gpio-chip class device registration and deregistration.
The class device is registered when a gpio-chip is added (or from
gpiolib_sysfs_init post-core init call), and deregistered when the chip
is removed.
Store the class device in struct gpio_chip directly rather than do a
class-device lookup on deregistration. This also removes the need for
the exported flag.
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Reduce scope of sysfs_lock protection during chip export and unexport,
which is only needed to prevent gpiod (re-)exports during chip removal.
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Put the recently introduced gpio-chip pointer to some more use in
gpiod_export.
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Drivers should call gpiochip_lock_as_irq (which prevents the pin
direction from being changed) in their irq_request_resources callbacks
but some drivers currently fail to do so.
Instead a second, explicit and often redundant call to lock-as-irq is
made by the sysfs-interface implementation after an irq has been
requested.
Move the explicit call before the irq-request to match the unlock done
after the irq is later released. Note that this also fixes an irq leak,
should the explicit call ever have failed.
Also add a comment about removing the redundant call once the broken
drivers have been fixed.
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Clean up gpiochip_remove somewhat and only output warning about removing
chip with GPIOs requested once.
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Linux 4.1-rc3
|
|
Fix kernel-doc format:
- Add gpio-width description
- Remove additional "inited" variable description
- Add return value description - xgpio_remove
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
priv->irq is allocated using devm_kzalloc so there is no need to memset it.
Signed-off-by: Christophe Jaillet <christophe.jaillet@wanadoo.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The platform_device_id is not modified by the driver and core uses it as
const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This file is built off of a tristate Kconfig option and also contains
modular function calls so it should explicitly include module.h to
avoid compile breakage during header shuffles done in the future.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
ACPI specification knows two types of GPIOs: GpioIo and GpioInt. The latter
is used to describe that a given device interrupt line is connected to a
specific GPIO pin. Typical ACPI _CRS entry for such device looks like
below:
Name (_CRS, ResourceTemplate ()
{
I2cSerialBus (0x004A, ControllerInitiated, 0x00061A80,
AddressingMode7Bit, "\\_SB.PCI0.I2C6",
0x00, ResourceConsumer)
GpioIo (Exclusive, PullDefault, 0x0000, 0x0000,
IoRestrictionOutputOnly, "\\_SB.GPO0",
0x00, ResourceConsumer)
{
0x004B
}
GpioInt (Level, ActiveLow, Shared, PullDefault, 0x0000,
"\\_SB.GPO0", 0x00, ResourceConsumer)
{
0x004C
}
})
Currently drivers need to request a GPIO corresponding to the right GpioInt
and then translate that to Linux IRQ number. This adds unnecessary lines of
boiler-plate code.
We can ease this a bit by introducing acpi_dev_gpio_irq_get() analogous to
of_irq_get(). This function translates given GpioInt resource under the
device in question to the suitable Linux IRQ number.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
All supported iMX GPIO controllers store configured GPIO output value
in GPIO_DR data register, which is represented by GPIO generic reg_set.
Provide a BGPIOF_READ_OUTPUT_REG_SET flag to bgpio_init() to allow
correct getting of previously set output value.
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Adding a BGPIOF_READ_OUTPUT_REG_SET initialization flag to GPIO
generic MMIO driver makes possible to remove a private get() value
function from the driver.
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The change introduces BGPIOF_READ_OUTPUT_REG_SET flag for gpio-generic
GPIO chip implementation, which allows to get correct configured value
from reg_set register, input value is still get from reg_dat.
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add GPIO controller driver for Netlogic XLP MIPS64 SOCs.
This driver is instantiated by device tree and supports interrupts
for GPIOs.
Signed-off-by: Kamlakant Patel <kamlakant.patel@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The irq_domain_ops are not modified by the driver and the irqdomain core
code accepts pointer to a const data.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
We currently get all kinds of errors building the omap gpio driver
as a module starting with:
undefined reference to `omap2_gpio_resume_after_idle'
undefined reference to `omap2_gpio_prepare_for_idle'
...
Let's fix the issue by adding inline functions to the header.
Note that we can now also remove the two unused functions for
omap_set_gpio_debounce and omap_set_gpio_debounce_time.
Then doing rmmod on the module produces further warnings
because of missing exit related functions. Let's add those.
And finally, we can make the Kconfig entry just a tristate
option that's selected for omaps.
Cc: Javier Martinez Canillas <javier@dowhile0.org>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@linaro.org>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
At some point with all the GPIO clean-up we've broken the
MPUIO interrupts. Those are just a little bit different from
the GPIO interrupts, so we can fix it up just by setting
different irqchip functions for it. And then we can just
remove all old code trying to do the same.
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Javier Martinez Canillas <javier@dowhile0.org>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@linaro.org>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
MAX732X clears all pending interrupts on I2C read (when interrupts
register is being read). Driver doesn't need to send any ACKs when
interrupt was handled. So replace handle_edge_irq() with
handle_simple_irq().
Using handle_edge_irq() (w/o .irq_ack callback set) may lead to NULL
pointer dereference in some cases. E.g. this was observed on
hibernation process:
Unable to handle kernel NULL pointer dereference at virtual address 0
Backtrace:
(handle_edge_irq) from (resend_irqs)
(resend_irqs) from (tasklet_action)
(tasklet_action) from (__do_softirq)
(__do_softirq) from (run_ksoftirqd)
(run_ksoftirqd) from (smpboot_thread_fn)
(smpboot_thread_fn) from (kthread)
(kthread) from (ret_from_fork)
Signed-off-by: Semen Protsenko <semen.protsenko@globallogic.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
It's possible that multiple MAX732X can be hooked up to the same
interrupt line with the processor. So add IRQF_SHARED in requesting irq.
Signed-off-by: Semen Protsenko <semen.protsenko@globallogic.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Driver for the GPIO block found on NXP LPC18xx/43xx devices.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Set .irq_set_wake callback to prevent possible issues on wake-up.
This patch was inspired by this commit:
b80eef95beb04760629822fa130aeed54cdfafca
Signed-off-by: Semen Protsenko <semen.protsenko@globallogic.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Unregister GPIOs requested through sysfs at chip remove to avoid leaking
the associated memory and sysfs entries.
The stale sysfs entries prevented the gpio numbers from being exported
when the gpio range was later reused (e.g. at device reconnect).
This also fixes the related module-reference leak.
Note that kernfs makes sure that any on-going sysfs operations finish
before the class devices are unregistered and that further accesses
fail.
The chip exported flag is used to prevent gpiod exports during removal.
This also makes it harder to trigger, but does not fix, the related race
between gpiochip_remove and export_store, which is really a race with
gpiod_request that needs to be addressed separately.
Also note that this would prevent the crashes (e.g. NULL-dereferences)
at reconnect that affects pre-3.18 kernels, as well as use-after-free on
operations on open attribute files on pre-3.14 kernels (prior to
kernfs).
Fixes: d8f388d8dc8d ("gpio: sysfs interface")
Cc: stable <stable@vger.kernel.org> # v2.6.27: 01cca93a9491
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Implement gpio_chip's get_direction() callback, that lets other drivers get
particular GPIOs direction using gpiod_get_direction().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The signed error will be wrongly used as valid gpio offset
Reported-by: David Binderman <dcb314@hotmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Qipeng Zha <qipeng.zha@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"We've got a fairly large cleanup branch this time. The bulk of this
is removal of non-DT platforms of several flavors:
- Atmel at91 platforms go full-DT, with removal of remaining
board-file based support
- OMAP removes legacy board files for three more platforms
- removal of non-DT mach-msm, newer Qualcomm platforms now live in
mach-qcom
- Freescale i.MX25 also removes non-DT platform support"
Most of the rest of the changes here are fallout from the above, i.e. for
example removal of drivers that now lack platforms, etc.
* tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (58 commits)
mmc: Remove msm_sdcc driver
gpio: Remove gpio-msm-v1 driver
ARM: Remove mach-msm and associated ARM architecture code
ARM: shmobile: cpuidle: Remove the pointless default driver
ARM: davinci: dm646x: Add interrupt resource for McASPs
ARM: davinci: irqs: Correct McASP1 TX interrupt definition for DM646x
ARM: davinci: dm646x: Clean up the McASP DMA resources
ARM: davinci: devices-da8xx: Add support for McASP2 on da830
ARM: davinci: devices-da8xx: Clean up and correct the McASP device creation
ARM: davinci: devices-da8xx: Add interrupt resource to McASP structs
ARM: davinci: devices-da8xx: Add resource name for the McASP DMA request
ARM: OMAP2+: Remove legacy support for omap3 TouchBook
ARM: OMAP3: Remove legacy support for devkit8000
ARM: OMAP3: Remove legacy support for EMA-Tech Stalker board
ARM: shmobile: Consolidate the pm code for R-Car Gen2
ARM: shmobile: r8a7791: Correct SYSCIER value
ARM: shmobile: r8a7790: Correct SYSCIER value
ARM: at91: remove old setup
ARM: at91: sama5d4: remove useless map_io
ARM: at91: sama5 use SoC detection infrastructure
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.1 development cycle:
- A new GPIO hogging mechanism has been added. This can be used on
boards that want to drive some GPIO line high, low, or set it as
input on boot and then never touch it again. For some embedded
systems this is bliss and simplifies things to a great extent.
- Some API cleanup and closure: gpiod_get_array() and
gpiod_put_array() has been added to get and put GPIOs in bulk as
was possible with the non-descriptor API.
- Encapsulate cross-calls to the pin control subsystem in
<linux/gpio/driver.h>. Now this should be the only header any GPIO
driver needs to include or something is wrong. Cleanups
restricting drivers to this include are welcomed if tested.
- Sort the GPIO Kconfig and split it into submenus, as it was
becoming and unstructured, illogical and unnavigatable mess. I
hope this is easier to follow. Menus that require a certain
subsystem like I2C can now be hidden nicely for example, still
working on others.
- New drivers:
- New driver for the Altera Soft GPIO.
- The F7188x driver now handles the F71869 and F71869A variants.
- The MIPS Loongson driver has been moved to drivers/gpio for
consolidation and cleanup.
- Cleanups:
- The MAX732x is converted to use the GPIOLIB_IRQCHIP
infrastructure.
- The PCF857x is converted to use the GPIOLIB_IRQCHIP
infrastructure.
- Radical cleanup of the OMAP driver.
- Misc:
- Enable the DWAPB GPIO for all architectures. This is a "hard
IP" block from Synopsys which has started to turn up in so
diverse architectures as X86 Quark, ARC and a slew of ARM
systems. So even though it's not an expander, it's generic
enough to be available for all.
- We add a mock GPIO on Crystalcove PMIC after a long discussion
with Daniel Vetter et al, tracing back to the shootout at the
kernel summit where DRM drivers and sub-componentization was
discussed. In this case a mock GPIO is assumed to be the best
compromise gaining some reuse of infrastructure without making
DRM drivers overly complex at the same time. Let's see"
* tag 'gpio-v4.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (62 commits)
Revert "gpio: sch: use uapi/linux/pci_ids.h directly"
gpio: dwapb: remove dependencies
gpio: dwapb: enable for ARC
gpio: removing kfree remove functionality
gpio: mvebu: Fix mask/unmask managment per irq chip type
gpio: split GPIO drivers in submenus
gpio: move MFD GPIO drivers under their own comment
gpio: move BCM Kona Kconfig option
gpio: arrange SPI Kconfig symbols alphabetically
gpio: arrange PCI GPIO controllers alphabetically
gpio: arrange I2C Kconfig symbols alphabetically
gpio: arrange Kconfig symbols alphabetically
gpio: ich: Implement get_direction function
gpio: use (!foo) instead of (foo == NULL)
gpio: arizona: drop owner assignment from platform_drivers
gpio: max7300: remove 'ret' variable
gpio: use devm_kzalloc
gpio: sch: use uapi/linux/pci_ids.h directly
gpio: x-gene: fix devm_ioremap_resource() check
gpio: loongson: Add Loongson-3A/3B GPIO driver support
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI updates from Rafael Wysocki:
"These are mostly fixes and cleanups all over, although there are a few
items that sort of fall into the new feature category.
First off, we have new callbacks for PM domains that should help us to
handle some issues related to device initialization in a better way.
There also is some consolidation in the unified device properties API
area allowing us to use that inferface for accessing data coming from
platform initialization code in addition to firmware-provided data.
We have some new device/CPU IDs in a few drivers, support for new
chips and a new cpufreq driver too.
Specifics:
- Generic PM domains support update including new PM domain callbacks
to handle device initialization better (Russell King, Rafael J
Wysocki, Kevin Hilman)
- Unified device properties API update including a new mechanism for
accessing data provided by platform initialization code (Rafael J
Wysocki, Adrian Hunter)
- ARM cpuidle update including ARM32/ARM64 handling consolidation
(Daniel Lezcano)
- intel_idle update including support for the Silvermont Core in the
Baytrail SOC and for the Airmont Core in the Cherrytrail and
Braswell SOCs (Len Brown, Mathias Krause)
- New cpufreq driver for Hisilicon ACPU (Leo Yan)
- intel_pstate update including support for the Knights Landing chip
(Dasaratharaman Chandramouli, Kristen Carlson Accardi)
- QorIQ cpufreq driver update (Tang Yuantian, Arnd Bergmann)
- powernv cpufreq driver update (Shilpasri G Bhat)
- devfreq update including Tegra support changes (Tomeu Vizoso,
MyungJoo Ham, Chanwoo Choi)
- powercap RAPL (Running-Average Power Limit) driver update including
support for Intel Broadwell server chips (Jacob Pan, Mathias Krause)
- ACPI device enumeration update related to the handling of the
special PRP0001 device ID allowing DT-style 'compatible' property
to be used for ACPI device identification (Rafael J Wysocki)
- ACPI EC driver update including limited _DEP support (Lan Tianyu,
Lv Zheng)
- ACPI backlight driver update including a new mechanism to allow
native backlight handling to be forced on non-Windows 8 systems and
a new quirk for Lenovo Ideapad Z570 (Aaron Lu, Hans de Goede)
- New Windows Vista compatibility quirk for Sony VGN-SR19XN (Chen Yu)
- Assorted ACPI fixes and cleanups (Aaron Lu, Martin Kepplinger,
Masanari Iida, Mika Westerberg, Nan Li, Rafael J Wysocki)
- Fixes related to suspend-to-idle for the iTCO watchdog driver and
the ACPI core system suspend/resume code (Rafael J Wysocki, Chen Yu)
- PM tracing support for the suspend phase of system suspend/resume
transitions (Zhonghui Fu)
- Configurable delay for the system suspend/resume testing facility
(Brian Norris)
- PNP subsystem cleanups (Peter Huewe, Rafael J Wysocki)"
* tag 'pm+acpi-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (74 commits)
ACPI / scan: Fix NULL pointer dereference in acpi_companion_match()
ACPI / scan: Rework modalias creation when "compatible" is present
intel_idle: mark cpu id array as __initconst
powercap / RAPL: mark rapl_ids array as __initconst
powercap / RAPL: add ID for Broadwell server
intel_pstate: Knights Landing support
intel_pstate: remove MSR test
cpufreq: fix qoriq uniprocessor build
ACPI / scan: Take the PRP0001 position in the list of IDs into account
ACPI / scan: Simplify acpi_match_device()
ACPI / scan: Generalize of_compatible matching
device property: Introduce firmware node type for platform data
device property: Make it possible to use secondary firmware nodes
PM / watchdog: iTCO: stop watchdog during system suspend
cpufreq: hisilicon: add acpu driver
ACPI / EC: Call acpi_walk_dep_device_list() after installing EC opregion handler
cpufreq: powernv: Report cpu frequency throttling
intel_idle: Add support for the Airmont Core in the Cherrytrail and Braswell SOCs
intel_idle: Update support for Silvermont Core in Baytrail SOC
PM / devfreq: tegra: Register governor on module init
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"Changes to existing drivers:
- Rename child driver [axp288_battery => axp288_fuel_gauge]; axp20x
- Rename child driver [max77693-flash => max77693-led]; max77693
- Error handling fixes; intel_soc_pmic
- GPIO tweaking; intel_soc_pmic
- Remove non-DT code; vexpress-sysreg, tc3589x
- Remove unused/legacy code; ti_am335x_tscadc, rts5249, rtsx_gops, rtsx_pcr,
rtc-s5m, sec-core, max77693, menelaus,
wm5102-tables
- Trivial fixups; rtsx_pci, da9150-core, sec-core, max7769, max77693,
mc13xxx-core, dln2, hi6421-pmic-core, rk808, twl4030-power,
lpc_ich, menelaus, twl6040
- Update register/address values; rts5227, rts5249
- DT and/or binding document fixups; arizona, da9150, mt6397, axp20x,
qcom-rpm, qcom-spmi-pmic
- Couple of trivial core Kconfig fixups
- Remove use of seq_printf return value; ab8500-debugfs
- Remove __exit markups; menelaus, tps65010
- Fix platform-device name collisions; mfd-core
New drivers/supported devices:
- Add support for wm8280/wm8281 into arizona
- Add support for COMe-cBL6 into kempld-core
- Add support for rts524a and rts525a into rts5249
- Add support for ipq8064 into qcom_rpm
- Add support for extcon into axp20x
- New MediaTek MT6397 PMIC driver
- New Maxim MAX77843 PMIC dirver
- New Intel Quark X1000 I2C-GPIO driver
- New Skyworks SKY81452 driver"
* tag 'mfd-for-linus-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (76 commits)
mfd: sec: Fix RTC alarm interrupt number on S2MPS11
mfd: wm5102: Remove registers for output 3R from readable list
mfd: tps65010: Remove incorrect __exit markups
mfd: devicetree: bindings: Add Qualcomm RPM regulator subnodes
mfd: axp20x: Add support for extcon cell
mfd: lpc_ich: Sort IDs
mfd: twl6040: Remove wrong and unneeded "platform:twl6040" modalias
mfd: qcom-spmi-pmic: Add specific compatible strings for Qualcomm's SPMI PMIC's
mfd: axp20x: Fix duplicate const for model names
mfd: menelaus: Use macro for magic number
mfd: menelaus: Drop support for SW controller VCORE
mfd: menelaus: Delete omap_has_menelaus
mfd: arizona: Correct type of gpio_defaults
mfd: lpc_ich: Sort IDs
mfd: Fix a typo in Kconfig
mfd: qcom_rpm: Add support for IPQ8064
mfd: devicetree: qcom_rpm: Document IPQ8064 resources
mfd: core: Fix platform-device name collisions
mfd: intel_quark_i2c_gpio: Don't crash if !DMI
dt-bindings: Add vendor-prefix for X-Powers
...
|
|
* device-properties:
device property: Introduce firmware node type for platform data
device property: Make it possible to use secondary firmware nodes
driver core: Implement device property accessors through fwnode ones
driver core: property: Update fwnode_property_read_string_array()
driver core: Add comments about returning array counts
ACPI: Introduce has_acpi_companion()
driver core / ACPI: Represent ACPI companions using fwnode_handle
|
|
This reverts commit d1e10dc8c104d533547f6e499550fafc36809943.
This commit should not go through this tree.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The Synopsys DesignWare DWAPB GPIO block is popular to
synthesize amongst many architectures: X86, ARM, ARC.
The driver was restricted to only these archs due to
using [read|write]l_relaxed() accessors that were not
universally available in the past,
but as of commit 9439eb3ab9d1ece6e4ad7baaa4a7f534f9b9dab0
"asm-generic: io: implement relaxed accessor macros as
conditional wrappers" these accessors are available on all
archs so this should not be a problem any more. Enable the
driver for all archs.
Cc: Alexey Brodkin <Alexey.Brodkin@synopsys.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
Johan Hovold
Linus Walleij
Michal Simek
Christophe Jaillet
Krzysztof Kozlowski
Paul Gortmaker
Mika Westerberg
Vladimir Zapolskiy
Kamlakant Patel
Tony Lindgren
Semen Protsenko
Joachim Eastwood
Axel Lin
Qipeng Zha
Linus Torvalds
Rafael J. Wysocki