| Age | Commit message (Collapse) | Author |
|---|
|
[ Upstream commit 6d9459d04081c796fc67c2bb771f4e4ebb5744c4 ]
CFGx.FIFO_MODE field controls a DMA-controller "FIFO readiness" criterion.
In other words it determines when to start pushing data out of a DW
DMAC channel FIFO to a destination peripheral or from a source
peripheral to the DW DMAC channel FIFO. Currently FIFO-mode is set to one
for all DW DMAC channels. It means they are tuned to flush data out of
FIFO (to a memory peripheral or by accepting the burst transaction
requests) when FIFO is at least half-full (except at the end of the block
transfer, when FIFO-flush mode is activated) and are configured to get
data to the FIFO when it's at least half-empty.
Such configuration is a good choice when there is no slave device involved
in the DMA transfers. In that case the number of bursts per block is less
than when CFGx.FIFO_MODE = 0 and, hence, the bus utilization will improve.
But the latency of DMA transfers may increase when CFGx.FIFO_MODE = 1,
since DW DMAC will wait for the channel FIFO contents to be either
half-full or half-empty depending on having the destination or the source
transfers. Such latencies might be dangerous in case if the DMA transfers
are expected to be performed from/to a slave device. Since normally
peripheral devices keep data in internal FIFOs, any latency at some
critical moment may cause one being overflown and consequently losing
data. This especially concerns a case when either a peripheral device is
relatively fast or the DW DMAC engine is relatively slow with respect to
the incoming data pace.
In order to solve problems, which might be caused by the latencies
described above, let's enable the FIFO half-full/half-empty "FIFO
readiness" criterion only for DMA transfers with no slave device involved.
Thanks to the commit 99ba8b9b0d97 ("dmaengine: dw: Initialize channel
before each transfer") we can freely do that in the generic
dw_dma_initialize_chan() method.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200731200826.9292-3-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e8ee6c8cb61b676f1a2d6b942329e98224bd8ee9 ]
DW DMA IP-core provides a way to synthesize the DMA controller with
channels having different parameters like maximum burst-length,
multi-block support, maximum data width, etc. Those parameters both
explicitly and implicitly affect the channels performance. Since DMA slave
devices might be very demanding to the DMA performance, let's provide a
functionality for the slaves to be assigned with DW DMA channels, which
performance according to the platform engineer fulfill their requirements.
After this patch is applied it can be done by passing the mask of suitable
DMA-channels either directly in the dw_dma_slave structure instance or as
a fifth cell of the DMA DT-property. If mask is zero or not provided, then
there is no limitation on the channels allocation.
For instance Baikal-T1 SoC is equipped with a DW DMAC engine, which first
two channels are synthesized with max burst length of 16, while the rest
of the channels have been created with max-burst-len=4. It would seem that
the first two channels must be faster than the others and should be more
preferable for the time-critical DMA slave devices. In practice it turned
out that the situation is quite the opposite. The channels with
max-burst-len=4 demonstrated a better performance than the channels with
max-burst-len=16 even when they both had been initialized with the same
settings. The performance drop of the first two DMA-channels made them
unsuitable for the DW APB SSI slave device. No matter what settings they
are configured with, full-duplex SPI transfers occasionally experience the
Rx FIFO overflow. It means that the DMA-engine doesn't keep up with
incoming data pace even though the SPI-bus is enabled with speed of 25MHz
while the DW DMA controller is clocked with 50MHz signal. There is no such
problem has been noticed for the channels synthesized with
max-burst-len=4.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20200731200826.9292-6-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b28de385b71abf31ce68ec0387638bee26ae9024 ]
After writing a garbage to the channel we get an Oops in dmatest_chan_set()
due to access to last entry in the empty list.
[ 212.670672] BUG: unable to handle page fault for address: fffffff000000020
[ 212.677562] #PF: supervisor read access in kernel mode
[ 212.682702] #PF: error_code(0x0000) - not-present page
...
[ 212.710074] RIP: 0010:dmatest_chan_set+0x149/0x2d0 [dmatest]
[ 212.715739] Code: e8 cc f9 ff ff 48 8b 1d 0d 55 00 00 48 83 7b 10 00 0f 84 63 01 00 00 48 c7 c7 d0 65 4d c0 e8 ee 4a f5 e1 48 89 c6 48 8b 43 10 <48> 8b 40 20 48 8b 78 58 48 85 ff 0f 84 f5 00 00 00 e8 b1 41 f5 e1
Fix this by checking list for emptiness before accessing its last entry.
Fixes: d53513d5dc28 ("dmaengine: dmatest: Add support for multi channel testing")
Cc: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20200922115847.30100-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8e84172e372bdca20c305d92d51d33640d2da431 ]
It's incorrect to check the channel's "busy" state without taking a lock.
That shouldn't cause any real troubles, nevertheless it's always better
not to have any race conditions in the code.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20200209163356.6439-5-digetx@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit d80cbef35bf89b763f06e03bb4ff8f933bf012c5 ]
To avoid race with vchan_complete, use the race free way to terminate
running transfer.
Move vdesc->node list_del in stm32_dma_start_transfer instead of in
stm32_mdma_chan_complete to avoid another race in vchan_dma_desc_free_list.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Link: https://lore.kernel.org/r/20200129153628.29329-9-amelie.delaunay@st.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit dfc708812a2acfc0ca56f56233b3c3e7b0d4ffe7 ]
To avoid race with vchan_complete, use the race free way to terminate
running transfer.
Move vdesc->node list_del in stm32_mdma_start_transfer instead of in
stm32_mdma_xfer_end to avoid another race in vchan_dma_desc_free_list.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Link: https://lore.kernel.org/r/20200127085334.13163-7-amelie.delaunay@st.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit cc88525ebffc757e00cc5a5d61da6271646c7f5f ]
Since the dma engine expects the burst length register content as
power of 2 value, the burst length needs to be converted first.
Additionally add a burst length range check to avoid corrupting unrelated
register bits.
Signed-off-by: Matthias Fend <matthias.fend@wolfvision.net>
Link: https://lore.kernel.org/r/20200115102249.24398-1-matthias.fend@wolfvision.net
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
fails
[ Upstream commit 1ff95243257fad07290dcbc5f7a6ad79d6e703e2 ]
When devm_request_irq fails, currently, the function
dma_async_device_unregister gets called. This doesn't free
the resources allocated by of_dma_controller_register.
Therefore, we have called of_dma_controller_free for this purpose.
Signed-off-by: Satendra Singh Thakur <sst2005@gmail.com>
Link: https://lore.kernel.org/r/20191109113523.6067-1-sst2005@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6d6018fc30bee67290dbed2fa51123f7c6f3d691 ]
In probe, IRQ is requested before zchan->id is initialized which can be
read in the irq handler. Hence, shift request irq after other initializations
complete.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Madhuparna Bhowmik <madhuparnabhowmik10@gmail.com>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20200821034423.12713-1-madhuparnabhowmik10@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 7eb48dd094de5fe0e216b550e73aa85257903973 ]
The acpi_get_table() should be coupled with acpi_put_table() if
the mapped table is not used at runtime to release the table
mapping, put the CSRT table buf after using it.
Signed-off-by: Hanjun Guo <guohanjun@huawei.com>
Link: https://lore.kernel.org/r/1595411661-15936-1-git-send-email-guohanjun@huawei.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 05655541c9503bfd01af4e6cbd7f5a29ac748e6c upstream.
Fix the source and destination physical address calculation of a
peripheral device on scatter-gather implementation.
This issue manifested during tests using a 64 bits architecture system.
The abnormal behavior wasn't visible before due to all previous tests
were done using 32 bits architecture system, that masked his effect.
Fixes: e63d79d1ffcd ("dmaengine: Add Synopsys eDMA IP core driver")
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Link: https://lore.kernel.org/r/8d3ab7e2ba96563fe3495b32f60077fffb85307d.1597327623.git.gustavo.pimentel@synopsys.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 0661cef675d37e2c4b66a996389ebeae8568e49e ]
Move the burst len fixup after setting the generic value for it. This
finally enables the fixup introduced by commit 137bd11090d8 ("dmaengine:
pl330: Align DMA memcpy operations to MFIFO width"), which otherwise was
overwritten by the generic value.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 137bd11090d8 ("dmaengine: pl330: Align DMA memcpy operations to MFIFO width")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20200825064617.16193-1-m.szyprowski@samsung.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
at_dma_xlate()
[ Upstream commit 0cef8e2c5a07d482ec907249dbd6687e8697677f ]
The reurn value of of_find_device_by_node() is not checked, thus null
pointer dereference will be triggered if of_find_device_by_node()
failed.
Fixes: bbe89c8e3d59 ("at_hdmac: move to generic DMA binding")
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Link: https://lore.kernel.org/r/20200817115728.1706719-2-yukuai3@huawei.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5b2aa9f918f6837ae943557f8cec02c34fcf80e7 ]
of_dma_xlate callback can return ERR_PTR as well NULL in case of failure.
If error code is returned (not NULL) then the route should be released and
the router should not be registered for the channel.
Fixes: 56f13c0d9524c ("dmaengine: of_dma: Support for DMA routers")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20200806104928.25975-1-peter.ujfalusi@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0a4c56c80f90797e9b9f8426c6aae4c0cf1c9785 ]
Commit ef91bb196b0d ("kernel.h: Silence sparse warning in
lower_32_bits") caused new warnings to show in the fsldma driver, but
that commit was not to blame: it only exposed some very incorrect code
that tried to take the low 32 bits of an address.
That made no sense for multiple reasons, the most notable one being that
that code was intentionally limited to only 32-bit ppc builds, so "only
low 32 bits of an address" was completely nonsensical. There were no
high bits to mask off to begin with.
But even more importantly fropm a correctness standpoint, turning the
address into an integer then caused the subsequent address arithmetic to
be completely wrong too, and the "+1" actually incremented the address
by one, rather than by four.
Which again was incorrect, since the code was reading two 32-bit values
and trying to make a 64-bit end result of it all. Surprisingly, the
iowrite64() did not suffer from the same odd and incorrect model.
This code has never worked, but it's questionable whether anybody cared:
of the two users that actually read the 64-bit value (by way of some C
preprocessor hackery and eventually the 'get_cdar()' inline function),
one of them explicitly ignored the value, and the other one might just
happen to work despite the incorrect value being read.
This patch at least makes it not fail the build any more, and makes the
logic superficially sane. Whether it makes any difference to the code
_working_ or not shall remain a mystery.
Compile-tested-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 87730ccbddcb48478b1b88e88b14e73424130764 ]
DMA transaction time to completion is a function of PCI bandwidth,
transaction size and a queue depth. So hard coded value for timeouts
might be wrong for some scenarios.
Signed-off-by: Leonid Ravich <Leonid.Ravich@emc.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/20200701184816.29138-1-leonid.ravich@dell.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8678c71c17721e0f771f135967ef0cce8f69ce9a ]
Due to recent fixes in m68k arch-specific I/O accessor macros, this
driver is not working anymore for ColdFire. Fix wrong tcd endianness
removing additional swaps, since edma_writex() functions should already
take care of any eventual swap if needed.
Note, i could only test the change in ColdFire mcf54415 and Vybrid
vf50 / Colibri where i don't see any issue. So, every feedback and
test for all other SoCs involved is really appreciated.
Signed-off-by: Angelo Dureghello <angelo.dureghello@timesys.com>
Reported-by: kbuild test robot <lkp@intel.com>
Link: https://lore.kernel.org/r/20200701225205.1674463-1-angelo.dureghello@timesys.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5b78fac4b1ba731cf4177fdbc1e3a4661521bcd0 ]
pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code. Thus a pairing decrement is needed on
the error handling path to keep the counter balanced.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20200624064626.19855-1-dinghao.liu@zju.edu.cn
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit e142087b15960a4e1e5932942e5abae1f49d2318 upstream.
Correct EDMA_TCD_ATTR_DSIZE_32BYTE define since it's broken by the below:
'0x0005 --> BIT(3) | BIT(0))'
Fixes: 4d6d3a90e4ac ("dmaengine: fsl-edma: fix macros")
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Tested-by: Angelo Dureghello <angelo@sysam.it>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/1593449998-32091-1-git-send-email-yibin.gong@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8995aa3d164ddd9200e6abcf25c449cf5298c858 upstream.
On Toradex Colibri VF50 (Vybrid VF5xx) with fsl-edma driver NULL pointer
exception happens occasionally on serial output initiated by login
timeout.
This was reproduced only if kernel was built with significant debugging
options and EDMA driver is used with serial console.
Issue looks like a race condition between interrupt handler
fsl_edma_tx_handler() (called as a result of fsl_edma_xfer_desc()) and
terminating the transfer with fsl_edma_terminate_all().
The fsl_edma_tx_handler() handles interrupt for a transfer with already
freed edesc and idle==true.
The mcf-edma driver shares design and lot of code with fsl-edma. It
looks like being affected by same problem. Fix this pattern the same
way as fix for fsl-edma driver.
Fixes: e7a3ff92eaf1 ("dmaengine: fsl-edma: add ColdFire mcf5441x edma support")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Robin Gong <yibin.gong@nxp.com>
Link: https://lore.kernel.org/r/1591881665-25592-1-git-send-email-krzk@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f5e5677c420346b4e9788051c2e4d750996c428c upstream.
NULL pointer exception happens occasionally on serial output initiated
by login timeout. This was reproduced only if kernel was built with
significant debugging options and EDMA driver is used with serial
console.
col-vf50 login: root
Password:
Login timed out after 60 seconds.
Unable to handle kernel NULL pointer dereference at virtual address 00000044
Internal error: Oops: 5 [#1] ARM
CPU: 0 PID: 157 Comm: login Not tainted 5.7.0-next-20200610-dirty #4
Hardware name: Freescale Vybrid VF5xx/VF6xx (Device Tree)
(fsl_edma_tx_handler) from [<8016eb10>] (__handle_irq_event_percpu+0x64/0x304)
(__handle_irq_event_percpu) from [<8016eddc>] (handle_irq_event_percpu+0x2c/0x7c)
(handle_irq_event_percpu) from [<8016ee64>] (handle_irq_event+0x38/0x5c)
(handle_irq_event) from [<801729e4>] (handle_fasteoi_irq+0xa4/0x160)
(handle_fasteoi_irq) from [<8016ddcc>] (generic_handle_irq+0x34/0x44)
(generic_handle_irq) from [<8016e40c>] (__handle_domain_irq+0x54/0xa8)
(__handle_domain_irq) from [<80508bc8>] (gic_handle_irq+0x4c/0x80)
(gic_handle_irq) from [<80100af0>] (__irq_svc+0x70/0x98)
Exception stack(0x8459fe80 to 0x8459fec8)
fe80: 72286b00 e3359f64 00000001 0000412d a0070013 85c98840 85c98840 a0070013
fea0: 8054e0d4 00000000 00000002 00000000 00000002 8459fed0 8081fbe8 8081fbec
fec0: 60070013 ffffffff
(__irq_svc) from [<8081fbec>] (_raw_spin_unlock_irqrestore+0x30/0x58)
(_raw_spin_unlock_irqrestore) from [<8056cb48>] (uart_flush_buffer+0x88/0xf8)
(uart_flush_buffer) from [<80554e60>] (tty_ldisc_hangup+0x38/0x1ac)
(tty_ldisc_hangup) from [<8054c7f4>] (__tty_hangup+0x158/0x2bc)
(__tty_hangup) from [<80557b90>] (disassociate_ctty.part.1+0x30/0x23c)
(disassociate_ctty.part.1) from [<8011fc18>] (do_exit+0x580/0xba0)
(do_exit) from [<801214f8>] (do_group_exit+0x3c/0xb4)
(do_group_exit) from [<80121580>] (__wake_up_parent+0x0/0x14)
Issue looks like race condition between interrupt handler fsl_edma_tx_handler()
(called as result of fsl_edma_xfer_desc()) and terminating the transfer with
fsl_edma_terminate_all().
The fsl_edma_tx_handler() handles interrupt for a transfer with already freed
edesc and idle==true.
Fixes: d6be34fbd39b ("dma: Add Freescale eDMA engine driver support")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Robin Gong <yibin.gong@nxp.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/1591877861-28156-2-git-send-email-krzk@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit fd17d1abce426b4224a916a242b57be94272771b ]
The completed threads were not cleared and consequent run would result
threads accumulating:
echo 800000 > /sys/module/dmatest/parameters/test_buf_size
echo 2000 > /sys/module/dmatest/parameters/timeout
echo 50 > /sys/module/dmatest/parameters/iterations
echo 1 > /sys/module/dmatest/parameters/max_channels
echo "" > /sys/module/dmatest/parameters/channel
[ 237.507265] dmatest: Added 1 threads using dma1chan2
echo 1 > /sys/module/dmatest/parameters/run
[ 244.713360] dmatest: Started 1 threads using dma1chan2
[ 246.117680] dmatest: dma1chan2-copy0: summary 50 tests, 0 failures 2437.47 iops 977623 KB/s (0)
echo 1 > /sys/module/dmatest/parameters/run
[ 292.381471] dmatest: No channels configured, continue with any
[ 292.389307] dmatest: Added 1 threads using dma1chan3
[ 292.394302] dmatest: Started 1 threads using dma1chan2
[ 292.399454] dmatest: Started 1 threads using dma1chan3
[ 293.800835] dmatest: dma1chan3-copy0: summary 50 tests, 0 failures 2624.53 iops 975014 KB/s (0)
echo 1 > /sys/module/dmatest/parameters/run
[ 307.301429] dmatest: No channels configured, continue with any
[ 307.309212] dmatest: Added 1 threads using dma1chan4
[ 307.314197] dmatest: Started 1 threads using dma1chan2
[ 307.319343] dmatest: Started 1 threads using dma1chan3
[ 307.324492] dmatest: Started 1 threads using dma1chan4
[ 308.730773] dmatest: dma1chan4-copy0: summary 50 tests, 0 failures 2390.28 iops 965436 KB/s (0)
Fixes: 6b41030fdc79 ("dmaengine: dmatest: Restore default for channel")
Reported-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20200701101225.8607-1-peter.ujfalusi@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 99ba8b9b0d9780e9937eb1d488d120e9e5c2533d ]
In some cases DMA can be used only with a consumer which does runtime power
management and on the platforms, that have DMA auto power gating logic
(see comments in the drivers/acpi/acpi_lpss.c), may result in DMA losing
its context. Simple mitigation of this issue is to initialize channel
each time the consumer initiates a transfer.
Fixes: cfdf5b6cc598 ("dw_dmac: add support for Lynxpoint DMA controllers")
Reported-by: Tsuchiya Yuto <kitakar@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=206403
Link: https://lore.kernel.org/r/20200705115620.51929-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 466257d9968ac79575831250b039dc07566c7b13 ]
A client driver (renesas_usbhs) assumed that
dmaengine_tx_status() could return the residue even if
the transfer was completed. However, this was not correct
usage [1] and this caused to break getting the residue after
the commit 24461d9792c2 ("dmaengine: virt-dma: Fix access after
free in vchan_complete()") actually. So, this is possible to get
wrong received size if the usb controller gets a short packet.
For example, g_zero driver causes "bad OUT byte" errors.
To use the tx_result from the renesas_usbhs driver when
the transfer is completed, set the tx_result parameters.
Notes that the renesas_usbhs driver needs to update for it.
[1]
https://lore.kernel.org/dmaengine/20200616165550.GP2324254@vkoul-mobl/
Reported-by: Hien Dang <hien.dang.eb@renesas.com>
Fixes: 24461d9792c2 ("dmaengine: virt-dma: Fix access after free in vchan_complete()")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/1592482053-19433-1-git-send-email-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit f8f482deb078389b42768b2193e050a81aae137d upstream.
When the kernel is built with lockdep support and the owl-dma driver is
used, the following message is shown:
[ 2.496939] INFO: trying to register non-static key.
[ 2.501889] the code is fine but needs lockdep annotation.
[ 2.507357] turning off the locking correctness validator.
[ 2.512834] CPU: 0 PID: 12 Comm: kworker/0:1 Not tainted 5.6.3+ #15
[ 2.519084] Hardware name: Generic DT based system
[ 2.523878] Workqueue: events_freezable mmc_rescan
[ 2.528681] [<801127f0>] (unwind_backtrace) from [<8010da58>] (show_stack+0x10/0x14)
[ 2.536420] [<8010da58>] (show_stack) from [<8080fbe8>] (dump_stack+0xb4/0xe0)
[ 2.543645] [<8080fbe8>] (dump_stack) from [<8017efa4>] (register_lock_class+0x6f0/0x718)
[ 2.551816] [<8017efa4>] (register_lock_class) from [<8017b7d0>] (__lock_acquire+0x78/0x25f0)
[ 2.560330] [<8017b7d0>] (__lock_acquire) from [<8017e5e4>] (lock_acquire+0xd8/0x1f4)
[ 2.568159] [<8017e5e4>] (lock_acquire) from [<80831fb0>] (_raw_spin_lock_irqsave+0x3c/0x50)
[ 2.576589] [<80831fb0>] (_raw_spin_lock_irqsave) from [<8051b5fc>] (owl_dma_issue_pending+0xbc/0x120)
[ 2.585884] [<8051b5fc>] (owl_dma_issue_pending) from [<80668cbc>] (owl_mmc_request+0x1b0/0x390)
[ 2.594655] [<80668cbc>] (owl_mmc_request) from [<80650ce0>] (mmc_start_request+0x94/0xbc)
[ 2.602906] [<80650ce0>] (mmc_start_request) from [<80650ec0>] (mmc_wait_for_req+0x64/0xd0)
[ 2.611245] [<80650ec0>] (mmc_wait_for_req) from [<8065aa10>] (mmc_app_send_scr+0x10c/0x144)
[ 2.619669] [<8065aa10>] (mmc_app_send_scr) from [<80659b3c>] (mmc_sd_setup_card+0x4c/0x318)
[ 2.628092] [<80659b3c>] (mmc_sd_setup_card) from [<80659f0c>] (mmc_sd_init_card+0x104/0x430)
[ 2.636601] [<80659f0c>] (mmc_sd_init_card) from [<8065a3e0>] (mmc_attach_sd+0xcc/0x16c)
[ 2.644678] [<8065a3e0>] (mmc_attach_sd) from [<8065301c>] (mmc_rescan+0x3ac/0x40c)
[ 2.652332] [<8065301c>] (mmc_rescan) from [<80143244>] (process_one_work+0x2d8/0x780)
[ 2.660239] [<80143244>] (process_one_work) from [<80143730>] (worker_thread+0x44/0x598)
[ 2.668323] [<80143730>] (worker_thread) from [<8014b5f8>] (kthread+0x148/0x150)
[ 2.675708] [<8014b5f8>] (kthread) from [<801010b4>] (ret_from_fork+0x14/0x20)
[ 2.682912] Exception stack(0xee8fdfb0 to 0xee8fdff8)
[ 2.687954] dfa0: 00000000 00000000 00000000 00000000
[ 2.696118] dfc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 2.704277] dfe0: 00000000 00000000 00000000 00000000 00000013 00000000
The obvious fix would be to use 'spin_lock_init()' on 'pchan->lock'
before attempting to call 'spin_lock_irqsave()' in 'owl_dma_get_pchan()'.
However, according to Manivannan Sadhasivam, 'pchan->lock' was supposed
to only protect 'pchan->vchan' while 'od->lock' does a similar job in
'owl_dma_terminate_pchan()'.
Therefore, this patch substitutes 'pchan->lock' with 'od->lock' and
removes the 'lock' attribute in 'owl_dma_pchan' struct.
Fixes: 47e20577c24d ("dmaengine: Add Actions Semi Owl family S900 DMA driver")
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@gmail.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Andreas Färber <afaerber@suse.de>
Link: https://lore.kernel.org/r/c6e6cdaca252b5364bd294093673951036488cf0.1588439073.git.cristian.ciocaltea@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6b41030fdc79086db5d673c5ed7169f3ee8c13b9 upstream.
In case of dmatest is built-in and no channel was configured test
doesn't run with:
dmatest: Could not start test, no channels configured
Even though description to "channel" parameter claims that default is
any.
Add default channel back as it used to be rather than reject test with
no channel configuration.
Fixes: d53513d5dc285d9a95a534fc41c5c08af6b60eac ("dmaengine: dmatest: Add support for multi channel testing)
Reported-by: Dijil Mohan <Dijil.Mohan@arm.com>
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Link: https://lore.kernel.org/r/20200429071522.58148-1-vladimir.murzin@arm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3a5fd0dbd87853f8bd2ea275a5b3b41d6686e761 upstream.
Commit b53611fb1ce9 ("dmaengine: tegra210-adma: Fix crash during probe")
has moved some code in the probe function and reordered the error handling
path accordingly.
However, a goto has been missed.
Fix it and goto the right label if 'dma_async_device_register()' fails, so
that all resources are released.
Fixes: b53611fb1ce9 ("dmaengine: tegra210-adma: Fix crash during probe")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20200516214205.276266-1-christophe.jaillet@wanadoo.fr
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 0c89446379218698189a47871336cb30286a7197 ]
When a channel configuration fails, the status of the channel is set to
DEV_ERROR so that an attempt to submit it fails. However, this status
sticks until the heat end of the universe, making it impossible to
recover from the error.
Let's reset it when the channel is released so that further use of the
channel with correct configuration is not impacted.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Link: https://lore.kernel.org/r/20200419164912.670973-5-lkundrak@v3.sk
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 363c32701c7fdc8265a84b21a6a4f45d1202b9ca ]
With an invalid dma_slave_config set previously,
mmp_tdma_prep_dma_cyclic() would detect an error whilst configuring the
channel, but proceed happily on:
[ 120.756530] mmp-tdma d42a0800.adma: mmp_tdma: unknown burst size.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Link: https://lore.kernel.org/r/20200419164912.670973-2-lkundrak@v3.sk
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2e45676a4d33af47259fa186ea039122ce263ba9 ]
pd->dma.dev is read in irq handler pd_irq().
However, it is set to pdev->dev after request_irq().
Therefore, set pd->dma.dev to pdev->dev before request_irq() to
avoid data race between pch_dma_probe() and pd_irq().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Madhuparna Bhowmik <madhuparnabhowmik10@gmail.com>
Link: https://lore.kernel.org/r/20200416062335.29223-1-madhuparnabhowmik10@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit aa72f1d20ee973d68f26d46fce5e1cf6f9b7e1ca upstream.
If we do
% echo 1 > /sys/module/dmatest/parameters/run
[ 115.851124] dmatest: Could not start test, no channels configured
% echo dma8chan7 > /sys/module/dmatest/parameters/channel
[ 127.563872] dmatest: Added 1 threads using dma8chan7
% cat /sys/module/dmatest/parameters/wait
... !!! HANG !!! ...
The culprit is the commit 6138f967bccc
("dmaengine: dmatest: Use fixed point div to calculate iops")
which makes threads not to run, but pending and being kicked off by writing
to the 'run' node. However, it forgot to consider 'wait' routine to avoid
above mentioned case.
In order to fix this, check for really running threads, i.e. with pending
and done flags unset.
It's pity the culprit commit hadn't updated documentation and tested all
possible scenarios.
Fixes: 6138f967bccc ("dmaengine: dmatest: Use fixed point div to calculate iops")
Cc: Seraj Alijan <seraj.alijan@sondrel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200428113518.70620-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b9f960201249f20deea586b4ec814669b4c6b1c0 upstream.
Under some circumstances, i.e. when test is still running and about to
time out and user runs, for example,
grep -H . /sys/module/dmatest/parameters/*
the iterations parameter is not respected and test is going on and on until
user gives
echo 0 > /sys/module/dmatest/parameters/run
This is not what expected.
The history of this bug is interesting. I though that the commit
2d88ce76eb98 ("dmatest: add a 'wait' parameter")
is a culprit, but looking closer to the code I think it simple revealed the
broken logic from the day one, i.e. in the commit
0a2ff57d6fba ("dmaengine: dmatest: add a maximum number of test iterations")
which adds iterations parameter.
So, to the point, the conditional of checking the thread to be stopped being
first part of conjunction logic prevents to check iterations. Thus, we have to
always check both conditions to be able to stop after given iterations.
Since it wasn't visible before second commit appeared, I add a respective
Fixes tag.
Fixes: 2d88ce76eb98 ("dmatest: add a 'wait' parameter")
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20200424161147.16895-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 36d5d22090d13fd3a7a8c9663a711cbe6970aac8 upstream.
The caller is already holding the lock so this will deadlock.
Fixes: 0b58828c923e ("DMAENGINE: COH 901 318 remove irq counting")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20200217144050.3i4ymbytogod4ijn@kili.mountain
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c33ee1301c393a241d6424e36eff1071811b1064 upstream.
The interrupt handler puts a half-completed DMA descriptor on a free list
and then schedules tasklet to process bottom half of the descriptor that
executes client's callback, this creates possibility to pick up the busy
descriptor from the free list. Thus, let's disallow descriptor's re-use
until it is fully processed.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200209163356.6439-3-digetx@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 94788af4ed039476ff3527b0e6a12c1dc42cb022 upstream.
I was doing some experiments with I2C and noticed that Tegra APB DMA
driver crashes sometime after I2C DMA transfer termination. The crash
happens because tegra_dma_terminate_all() bails out immediately if pending
list is empty, and thus, it doesn't release the half-completed descriptors
which are getting re-used before ISR tasklet kicks-in.
tegra-i2c 7000c400.i2c: DMA transfer timeout
elants_i2c 0-0010: elants_i2c_irq: failed to read data: -110
------------[ cut here ]------------
WARNING: CPU: 0 PID: 142 at lib/list_debug.c:45 __list_del_entry_valid+0x45/0xac
list_del corruption, ddbaac44->next is LIST_POISON1 (00000100)
Modules linked in:
CPU: 0 PID: 142 Comm: kworker/0:2 Not tainted 5.5.0-rc2-next-20191220-00175-gc3605715758d-dirty #538
Hardware name: NVIDIA Tegra SoC (Flattened Device Tree)
Workqueue: events_freezable_power_ thermal_zone_device_check
[<c010e5c5>] (unwind_backtrace) from [<c010a1c5>] (show_stack+0x11/0x14)
[<c010a1c5>] (show_stack) from [<c0973925>] (dump_stack+0x85/0x94)
[<c0973925>] (dump_stack) from [<c011f529>] (__warn+0xc1/0xc4)
[<c011f529>] (__warn) from [<c011f7e9>] (warn_slowpath_fmt+0x61/0x78)
[<c011f7e9>] (warn_slowpath_fmt) from [<c042497d>] (__list_del_entry_valid+0x45/0xac)
[<c042497d>] (__list_del_entry_valid) from [<c047a87f>] (tegra_dma_tasklet+0x5b/0x154)
[<c047a87f>] (tegra_dma_tasklet) from [<c0124799>] (tasklet_action_common.constprop.0+0x41/0x7c)
[<c0124799>] (tasklet_action_common.constprop.0) from [<c01022ab>] (__do_softirq+0xd3/0x2a8)
[<c01022ab>] (__do_softirq) from [<c0124683>] (irq_exit+0x7b/0x98)
[<c0124683>] (irq_exit) from [<c0168c19>] (__handle_domain_irq+0x45/0x80)
[<c0168c19>] (__handle_domain_irq) from [<c043e429>] (gic_handle_irq+0x45/0x7c)
[<c043e429>] (gic_handle_irq) from [<c0101aa5>] (__irq_svc+0x65/0x94)
Exception stack(0xde2ebb90 to 0xde2ebbd8)
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200209163356.6439-2-digetx@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 25962e1a7f1d522f1b57ead2f266fab570042a70 upstream.
On i.MX6UL/ULL and i.MX6SX the DMA event id for the RX channel of
UART6 is '0'. To fix the broken DMA support for UART6, we change
the check for event_id0 to include '0' as a valid id.
Fixes: 1ec1e82f2510 ("dmaengine: Add Freescale i.MX SDMA support")
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200225082139.7646-1-frieder.schrempf@kontron.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d288bddd8374e0a043ac9dde64a1ae6a09411d74 upstream.
There is a DMA problem with the serial ports on i.MX6.
When the following sequence is performed:
1) Open a port
2) Write some data
3) Close the port
4) Open a *different* port
5) Write some data
6) Close the port
The second write sends nothing and the second close hangs.
If the first close() is omitted it works.
Adding logs to the the UART driver shows that the DMA is being setup but
the callback is never invoked for the second write.
This used to work in 4.19.
Git bisect leads to:
ad0d92d: "dmaengine: imx-sdma: refine to load context only once"
This commit adds a "context_loaded" flag used to avoid unnecessary context
setups.
However the flag is only reset in sdma_channel_terminate_work(),
which is only invoked in a worker triggered by sdma_terminate_all() IF
there is an active descriptor.
So, if no active descriptor remains when the channel is terminated, the
flag is not reset and, when the channel is later reused the old context
is used.
Fix the problem by always resetting the flag in sdma_free_chan_resources().
Cc: stable@vger.kernel.org
Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
Fixes: ad0d92d7ba6a ("dmaengine: imx-sdma: refine to load context only once")
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/1580305274-27274-1-git-send-email-martin.fuzzey@flowbird.group
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit 8a7aa4feeaeabc12181e1997a298eb73d2ed2d65 which is
commit 02939cd167095f16328a1bd5cab5a90b550606df upstream.
Andreas writes:
This patch breaks our imx6 board with the attached trace.
Reverting the patch makes it boot again.
Reported-by: Andreas Tobler <andreas.tobler@onway.ch>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Robin Gong <yibin.gong@nxp.com>
Cc: Vinod Koul <vkoul@kernel.org>
Cc: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 02939cd167095f16328a1bd5cab5a90b550606df ]
The current descriptor is not on any list of the virtual DMA channel.
Once sdma_terminate_all() is called when a descriptor is currently
in flight then this one is forgotten to be freed. We have to call
vchan_terminate_vdesc() on this descriptor to re-add it to the lists.
Now that we also free the currently running descriptor we can (and
actually have to) remove the current descriptor from its list also
for the cyclic case.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Robin Gong <yibin.gong@nxp.com>
Tested-by: Robin Gong <yibin.gong@nxp.com>
Link: https://lore.kernel.org/r/20191216105328.15198-10-s.hauer@pengutronix.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit dae7a589c18a4d979d5f14b09374e871b995ceb1 ]
dma_chan_to_owner() dereferences the driver from the struct device to
obtain the owner and call module_[get|put](). However, if the backing
device is unbound before the dma_device is unregistered, the driver
will be cleared and this will cause a NULL pointer dereference.
Instead, store a pointer to the owner module in the dma_device struct
so the module reference can be properly put when the channel is put, even
if the backing device was destroyed first.
This change helps to support a safer unbind of DMA engines.
If the dma_device is unregistered in the driver's remove function,
there's no guarantee that there are no existing clients and a users
action may trigger the WARN_ONCE in dma_async_device_unregister()
which is unlikely to leave the system in a consistent state.
Instead, a better approach is to allow the backing driver to go away
and fail any subsequent requests to it.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Link: https://lore.kernel.org/r/20191216190120.21374-2-logang@deltatee.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4b048178854da11656596d36a107577d66fd1e08 ]
There is duplicated argument to && in function fsl_qdma_free_chan_resources,
which looks like a typo, pointer fsl_queue->desc_pool also needs NULL check,
fix it.
Detected with coccinelle.
Fixes: b092529e0aa0 ("dmaengine: fsl-qdma: Add qDMA controller driver for Layerscape SoCs")
Signed-off-by: Chen Zhou <chenzhou10@huawei.com>
Reviewed-by: Peng Ma <peng.ma@nxp.com>
Tested-by: Peng Ma <peng.ma@nxp.com>
Link: https://lore.kernel.org/r/20200120125843.34398-1-chenzhou10@huawei.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit a5b982af953bcc838cd198b0434834cc1dff14ec upstream.
The driver misses checking the result of devm_regmap_init_mmio().
Add a check to fix it.
Fixes: fc15be39a827 ("dmaengine: axi-dmac: add regmap support")
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20191209085711.16001-1-hslester96@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 340049d453682a9fe8d91fe794dd091730f4bb25 ]
When devm_kcalloc fails, it forgets to call edma_free_slot.
Replace direct return with failure handler to fix it.
Fixes: 1be5336bc7ba ("dmaengine: edma: New device tree binding")
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Link: https://lore.kernel.org/r/20191118073802.28424-1-hslester96@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b0b5ce1010ffc50015eaec72b0028aaae3f526bb ]
If dma_alloc_coherent() returns NULL in ioat_alloc_ring(), ring
allocation must not proceed.
Until now, if the first call to dma_alloc_coherent() in
ioat_alloc_ring() returned NULL, the processing could proceed, failing
with NULL-pointer dereferencing further down the line.
Signed-off-by: Alexander Barabash <alexander.barabash@dell.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/75e9c0e84c3345d693c606c64f8b9ab5@x13pwhopdag1307.AMER.DELL.COM
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2f42e05b942fe2fbfb9bbc6e34e1dd8c3ce4f3a4 ]
In some cases we seem to submit two transactions in a row, which
causes us to lose track of the first. If we then cancel the
request, we may still get an interrupt, which traverses a null
ds_run value.
So try to avoid starting a new transaction if the ds_run value
is set.
While this patch avoids the null pointer crash, I've had some
reports of the k3dma driver still getting confused, which
suggests the ds_run/ds_done value handling still isn't quite
right. However, I've not run into an issue recently with it
so I think this patch is worth pushing upstream to avoid the
crash.
Signed-off-by: John Stultz <john.stultz@linaro.org>
[add ss tag]
Link: https://lore.kernel.org/r/20191218190906.6641-1-john.stultz@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit f27c22736d133baff0ab3fdc7b015d998267d817 upstream.
On some platforms the clock can be fixed rate, always running one and
there is no need to do anything with it.
In order to support those platforms, switch to use optional clock.
Fixes: f8d9ddbc2851 ("dmaengine: dw: platform: Enable iDMA 32-bit on Intel Elkhart Lake")
Depends-on: 60b8f0ddf1a9 ("clk: Add (devm_)clk_get_optional() functions")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Link: https://lore.kernel.org/r/20190924085116.83683-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 24461d9792c2c706092805ff1b067628933441bd upstream.
vchan_vdesc_fini() is freeing up 'vd' so the access to vd->tx_result is
via already freed up memory.
Move the vchan_vdesc_fini() after invoking the callback to avoid this.
Fixes: 09d5b702b0f97 ("dmaengine: virt-dma: store result on dma descriptor")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20191220131100.21804-1-peter.ujfalusi@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a40c94be2336f3002563c9ae16572143ae3422e2 upstream.
It turns out that the JZ4725B displays the same buggy behaviour as the
JZ4740 that was described in commit f4c255f1a747 ("dmaengine: dma-jz4780:
Break descriptor chains on JZ4740").
Work around it by using the same workaround previously used for the
JZ4740.
Fixes commit f4c255f1a747 ("dmaengine: dma-jz4780: Break descriptor
chains on JZ4740")
Cc: <stable@vger.kernel.org>
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20191210165545.59690-1-paul@crapouillou.net
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 41814c4eadf8a791b6d07114f96e7e120e59555c ]
platform_get_irq_byname() might return -errno which later would be cast
to an unsigned int and used in IRQ handling code leading to usage of
wrong ID and errors about wrong irq_base.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Peng Ma <peng.ma@nxp.com>
Tested-by: Peng Ma <peng.ma@nxp.com>
Link: https://lore.kernel.org/r/20191004150826.6656-1-krzk@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8a631a5a0f7d4a4a24dba8587d5d9152be0871cc ]
Whenever we reset the channel, we need to clear desc_pendingcount
along with desc_submitcount. Otherwise when a new transaction is
submitted, the irq coalesce level could be programmed to an incorrect
value in the axidma case.
This behavior can be observed when terminating pending transactions
with xilinx_dma_terminate_all() and then submitting new transactions
without releasing and requesting the channel.
Signed-off-by: Nicholas Graumann <nick.graumann@gmail.com>
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Link: https://lore.kernel.org/r/1571150904-3988-8-git-send-email-radhey.shyam.pandey@xilinx.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
Serge Semin
Andy Shevchenko
Dmitry Osipenko
Amelie Delaunay
Matthias Fend
Satendra Singh Thakur
Madhuparna Bhowmik
Hanjun Guo
Gustavo Pimentel
Marek Szyprowski
Yu Kuai
Peter Ujfalusi
Linus Torvalds
Leonid Ravich
Angelo Dureghello
Dinghao Liu
Robin Gong
Krzysztof Kozlowski
Yoshihiro Shimoda
Cristian Ciocaltea
Vladimir Murzin
Christophe JAILLET
Lubomir Rintel
Dan Carpenter
Frieder Schrempf
Martin Fuzzey
Greg Kroah-Hartman
Sascha Hauer
Logan Gunthorpe
Chen Zhou
Chuhong Yuan
Alexander.Barabash@dell.com
John Stultz
Paul Cercueil
Nicholas Graumann