| Age | Commit message (Collapse) | Author |
|---|
|
source channel
[ Upstream commit be83c3b6e7b8ff22f72827a613bf6f3aa5afadbb ]
If CMT instance has at least two channels, one channel will be used
as a clock source and another one used as a clock event device.
In that case, IRQ is not requested for clock source channel so
sh_cmt_clock_event_program_verify() might work incorrectly.
Besides, when a channel is only used for clock source, don't need to
re-set the next match_value since it should be maximum timeout as
it still is.
On the other hand, due to no IRQ, total_cycles is not counted up
when reaches compare match time (timer counter resets to zero),
so sh_cmt_clocksource_read() returns unexpected value.
Therefore, use 64-bit clocksoure's mask for 32-bit or 16-bit variants
will also lead to wrong delta calculation. Hence, this mask should
correspond to timer counter width, and above function just returns
the raw value of timer counter register.
Fixes: bfa76bb12f23 ("clocksource: sh_cmt: Request IRQ for clock event device only")
Fixes: 37e7742c55ba ("clocksource/drivers/sh_cmt: Fix clocksource width for 32-bit machines")
Signed-off-by: Phong Hoang <phong.hoang.wz@renesas.com>
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210422123443.73334-1-niklas.soderlund+renesas@ragnatech.se
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 7da390694afbaed8e0f05717a541dfaf1077ba51 ]
When DEBUG is defined this error occurs
drivers/clocksource/mxs_timer.c:138:1: error:
expected ‘;’ before ‘}’ token
The preceding statement needs a semicolon.
Replace pr_info() with pr_debug() and remove the unneeded ifdef.
Fixes: eb8703e2ef7c ("clockevents/drivers/mxs: Migrate to new 'set-state' interface")
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210118211955.763609-1-trix@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
CNTKCTL_EL1.EVNTI
[ Upstream commit 8b7770b877d187bfdae1eaf587bd2b792479a31c ]
ARM virtual counter supports event stream, it can only trigger an event
when the trigger bit (the value of CNTKCTL_EL1.EVNTI) of CNTVCT_EL0 changes,
so the actual period of event stream is 2^(cntkctl_evnti + 1). For example,
when the trigger bit is 0, then virtual counter trigger an event for every
two cycles.
While we're at it, rework the way we compute the trigger bit position
by making it more obvious that when bits [n:n-1] are both set (with n
being the most significant bit), we pick bit (n + 1).
Fixes: 037f637767a8 ("drivers: clocksource: add support for ARM architected timer event stream")
Suggested-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Keqian Zhu <zhukeqian1@huawei.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201204073126.6920-3-zhukeqian1@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit eee422c46e6840a81c9db18a497b74387a557b29 ]
If clk_notifier_register() failed, ttc_setup_clockevent() will return
without freeing 'ttcce', which will leak memory.
Fixes: 70504f311d4b ("clocksource/drivers/cadence_ttc: Convert init function to return error")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201116135123.2164033-1-yukuai3@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 400d033f5a599120089b5f0c54d14d198499af5a ]
In the init function, if the call to of_iomap() fails, the return
value is ENXIO instead of -ENXIO.
Change to the right negative errno.
Fixes: 691f8f878290f ("clocksource/drivers/h8300_timer8: Convert init function to return error")
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Tianjia Zhang <tianjia.zhang@linux.alibaba.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200802111541.5429-1-tianjia.zhang@linux.alibaba.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6d2e16a3181bafb77b535095c39ad1c8b9558c8c ]
Commit 100214889973 ("clocksource: dw_apb_timer_of: use
clocksource_of_init") replaced a publicly available driver
initialization method with one called by the timer_probe() method
available after CLKSRC_OF. In current implementation it traverses
all the timers available in the system and calls their initialization
methods if corresponding devices were either in dtb or in acpi. But
if before the commit any number of available timers would be installed
as clockevent and clocksource devices, after that there would be at most
two. The rest are just ignored since default case branch doesn't do
anything. I don't see a reason of such behaviour, neither the commit
message explains it. Moreover this might be wrong if on some platforms
these timers might be used for different purpose, as virtually CPU-local
clockevent timers and as an independent broadcast timer. So in order
to keep the compatibility with the platforms where the order of the
timers detection has some meaning, lets add the secondly discovered
timer to be of clocksource/sched_clock type, while the very first and
the others would provide the clockevents service.
Fixes: 100214889973 ("clocksource: dw_apb_timer_of: use clocksource_of_init")
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Paul Burton <paulburton@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: linux-rtc@vger.kernel.org
Cc: devicetree@vger.kernel.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200521204818.25436-7-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit cee43dbf2ee3f430434e2b66994eff8a1aeda889 ]
Currently the DW APB Timer driver binds each clockevent timers to a
particular CPU. This isn't good for multiple reasons. First of all seeing
the device is placed on APB bus (which makes it accessible from any CPU
core), accessible over MMIO and having the DYNIRQ flag set we can be sure
that manually binding the timer to any CPU just isn't correct. By doing
so we just set an extra limitation on device usage. This also doesn't
reflect the device actual capability, since by setting the IRQ affinity
we can make it virtually local to any CPU. Secondly imagine if you had a
real CPU-local timer with the same rating and the same CPU-affinity.
In this case if DW APB timer was registered first, then due to the
clockevent framework tick-timer selection procedure we'll end up with the
real CPU-local timer being left unselected for clock-events tracking. But
on most of the platforms (MIPS/ARM/etc) such timers are normally embedded
into the CPU core and are accessible with much better performance then
devices placed on APB. For instance in MIPS architectures there is
r4k-timer, which is CPU-local, assigned with the same rating, and normally
its clockevent device is registered after the platform-specific one.
So in order to fix all of these issues let's make the DW APB Timer CPU
affinity being optional and deactivated by passing a negative CPU id,
which will effectively set the DW APB clockevent timer cpumask to
'cpu_possible_mask'.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Paul Burton <paulburton@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: linux-rtc@vger.kernel.org
Cc: devicetree@vger.kernel.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200521204818.25436-5-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2052d032c06761330bca4944bb7858b00960e868 ]
Currently when setup_irq fails the error exit path will leak the
recently allocated timer structure. Originally the code would
throw a panic but a later commit changed the behaviour to return
via the err_iounmap path and hence we now have a memory leak. Fix
this by adding a err_timer_free error path that kfree's timer.
Addresses-Coverity: ("Resource Leak")
Fixes: 524a7f08983d ("clocksource/drivers/bcm2835_timer: Convert init function to return error")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20191219213246.34437-1-colin.king@canonical.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b9307420196009cdf18bad55e762ac49fb9a80f4 ]
While freeing interrupt handlers in error path, don't assume that all
requested interrupts are per-processor interrupts and properly release
standard interrupts too.
Reported-by: Krzysztof Kozlowski <krzk@kernel.org>
Fixes: 56a94f13919c ("clocksource: exynos_mct: Avoid blocking calls in the cpu hotplug notifier")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e7e7e0d7beafebd11b0c065cd5fbc1e5759c5aab ]
If the clock tree is not fully populated when the timer-sun5i init code
is called, attempts to get the clock rate for the timer would fail and
return 0.
Make the init code for both clock events and clocksource check the
returned clock rate and fail gracefully if the result is 0, instead of
causing a divide by 0 exception later on.
Fixes: 4a59058f0b09 ("clocksource/drivers/sun5i: Refactor the current code")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6e001f6a4cc73cd06fc7b8c633bc4906c33dd8ad ]
asm9260_timer_init misses a check for of_clk_get.
Add a check for it and print errors like other clocksource drivers.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20191016124330.22211-1-hslester96@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 86fe57fc47b17b3528fa5497fc57e158d846c4ea ]
TIMER_INTR_MASK register (Base Address of Timer + 0x38) is not designed
for masking interrupts on ast2500 chips, and it's not even listed in
ast2400 datasheet, so it's not safe to access TIMER_INTR_MASK on aspeed
chips.
Similarly, TIMER_INTR_STATE register (Base Address of Timer + 0x34) is
not interrupt status register on ast2400 and ast2500 chips. Although
there is no side effect to reset the register in fttmr010_common_init(),
it's just misleading to do so.
Besides, "count_down" is renamed to "is_aspeed" in "fttmr010" structure,
and more comments are added so the code is more readble.
Signed-off-by: Tao Ren <taoren@fb.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 37e7742c55ba856eaec7e35673ee370f36eb17f3 ]
The driver seems to abuse *unsigned long* not only for the (32-bit)
register values but also for the 'sh_cmt_channel::total_cycles' which
needs to always be 64-bit -- as a result, the clocksource's mask is
needlessly clamped down to 32-bits on the 32-bit machines...
Fixes: 19bdc9d061bc ("clocksource: sh_cmt clocksource support")
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 22627c6f3ed3d9d0df13eec3c831b08f8186c38e ]
When trying to use CMT for clockevents on R-Car gen3 SoCs, I noticed
that 'max_delta_ns' for the broadcast timer (CMT) was shown as 1000 in
/proc/timer_list. It turned out that when calculating it, the driver did
1 << 32 (causing what I think was undefined behavior) resulting in a zero
delta, later clamped to 1000 by cev_delta2ns(). The root cause turned out
to be that the driver abused *unsigned long* for the CMT register values
(which are 16/32-bit), so that the calculation of 'ch->max_match_value'
in sh_cmt_setup_channel() used the wrong branch. Using more proper 'u32'
instead fixed 'max_delta_ns' and even fixed the switching an active
clocksource to CMT (which caused the system to turn non-interactive
before).
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6282edb72bed5324352522d732080d4c1b9dfed6 ]
Exynos SoCs based on CA7/CA15 have 2 timer interfaces: custom Exynos MCT
(Multi Core Timer) and standard ARM Architected Timers.
There are use cases, where both timer interfaces are used simultanously.
One of such examples is using Exynos MCT for the main system timer and
ARM Architected Timers for the KVM and virtualized guests (KVM requires
arch timers).
Exynos Multi-Core Timer driver (exynos_mct) must be however started
before ARM Architected Timers (arch_timer), because they both share some
common hardware blocks (global system counter) and turning on MCT is
needed to get ARM Architected Timer working properly.
To ensure selecting Exynos MCT as the main system timer, increase MCT
timer rating. To ensure proper starting order of both timers during
suspend/resume cycle, increase MCT hotplug priority over ARM Archictected
Timers.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit fbc87aa0f7c429999dc31f1bac3b2615008cac32 ]
The OX820 compatible is wrong is the driver, fix it.
Fixes: 2ea3401e2a84 ("clocksource/drivers/oxnas: Add OX820 compatible")
Reported-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit d2f276c8d3c224d5b493c42b6cf006ae4e64fb1c upstream.
When shutting down the timer, ensure that after we have stopped the
timer any pending interrupts are cleared. This fixes a problem when
suspending, as interrupts are disabled before the timer is stopped,
so the timer interrupt may still be asserted, preventing the system
entering a low power state when the wfi is executed.
Signed-off-by: Stuart Menefy <stuart.menefy@mathembedded.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: <stable@vger.kernel.org> # v4.3+
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a5719a40aef956ba704f2aa1c7b977224d60fa96 upstream.
When a timer tick occurs and the clock is in one-shot mode, the timer
needs to be stopped to prevent it triggering subsequent interrupts.
Currently this code is in exynos4_mct_tick_clear(), but as it is
only needed when an ISR occurs move it into exynos4_mct_tick_isr(),
leaving exynos4_mct_tick_clear() just doing what its name suggests it
should.
Signed-off-by: Stuart Menefy <stuart.menefy@mathembedded.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: stable@vger.kernel.org # v4.3+
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 5eb73c831171115d3b4347e1e7124a5a35d8086c ]
The function of_find_node_by_path() acquires a reference to the node
returned by it and that reference needs to be dropped by its caller.
integrator_ap_timer_init_of() doesn't do that. The pri_node and the
sec_node are used as an identifier to compare against the current
node, so we can directly drop the refcount after getting the node from
the path as it is not used as pointer.
By dropping the refcount right after getting it, a single variable is
needed instead of two.
Fix this by use a single variable and drop the refcount right after
of_find_node_by_path().
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 35b69a420bfb56b7b74cb635ea903db05e357bec upstream.
Add support for platforms where pit_shutdown() doesn't work because of a
quirk in the PIT emulation. On these platforms setting the counter register
to zero causes the PIT to start running again, negating the shutdown.
Provide a global variable that controls whether the counter register is
zero'ed, which platform specific code can override.
Signed-off-by: Michael Kelley <mikelley@microsoft.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: "gregkh@linuxfoundation.org" <gregkh@linuxfoundation.org>
Cc: "devel@linuxdriverproject.org" <devel@linuxdriverproject.org>
Cc: "daniel.lezcano@linaro.org" <daniel.lezcano@linaro.org>
Cc: "virtualization@lists.linux-foundation.org" <virtualization@lists.linux-foundation.org>
Cc: "jgross@suse.com" <jgross@suse.com>
Cc: "akataria@vmware.com" <akataria@vmware.com>
Cc: "olaf@aepfle.de" <olaf@aepfle.de>
Cc: "apw@canonical.com" <apw@canonical.com>
Cc: vkuznets <vkuznets@redhat.com>
Cc: "jasowang@redhat.com" <jasowang@redhat.com>
Cc: "marcelo.cerri@canonical.com" <marcelo.cerri@canonical.com>
Cc: KY Srinivasan <kys@microsoft.com>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/1541303219-11142-2-git-send-email-mikelley@microsoft.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 4451d3f59f2a6f95e5d205c2d04ea072955d080d ]
Currently, the aspeed MATCH1 register is updated to <current_count -
cycles> in set_next_event handler, with the assumption that COUNT
register value is preserved when the timer is disabled and it continues
decrementing after the timer is enabled. But the assumption is wrong:
RELOAD register is loaded into COUNT register when the aspeed timer is
enabled, which means the next event may be delayed because timer
interrupt won't be generated until <0xFFFFFFFF - current_count +
cycles>.
The problem can be fixed by updating RELOAD register to <cycles>, and
COUNT register will be re-loaded when the timer is enabled and interrupt
is generated when COUNT register overflows.
The test result on Facebook Backpack-CMM BMC hardware (AST2500) shows
the issue is fixed: without the patch, usleep(100) suspends the process
for several milliseconds (and sometimes even over 40 milliseconds);
after applying the fix, usleep(100) takes averagely 240 microseconds to
return under the same workload level.
Signed-off-by: Tao Ren <taoren@fb.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Lei YU <mine260309@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
non-am43 SoCs
[ Upstream commit 3b7d96a0dbb6b630878597a1838fc39f808b761b ]
The 32k clocksource is NONSTOP for non-am43 SoCs. Hence
add the flag for all the other SoCs.
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 52bf4a900d9cede3eb14982d0f2c5e6db6d97cc3 upstream.
The smatch utility reports a possible leak:
smatch warnings:
drivers/clocksource/timer-atmel-pit.c:183 at91sam926x_pit_dt_init() warn: possible memory leak of 'data'
Ensure data is freed before exiting with an error.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 506a7be93ff773d5d4cf75a59f342865605b4910 ]
According to i.MX7ULP reference manual, TPM_SC_CPWMS can ONLY be written when
counter is disabled, TPM_SC_TOF is write-1-clear, TPM_C0SC_CHF is also
write-1-clear, correct these registers initialization flow;
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 5753405e27f8fe4c42c1537d3ddbd9e058e54cdc ]
__gic_clocksource_init() extracts the GIC_CONFIG_COUNTBITS field from
read_gic_config() by right shifting the register value. The shift count is
determined by the most significant bit (__fls) of the bitmask which is
wrong as it shifts out the complete bitfield.
Use the least significant bit (__ffs) instead to shift the bitfield down to
bit 0.
Fixes: e07127a077c7 ("clocksource: mips-gic-timer: Use new GIC accessor functions")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: daniel.lezcano@linaro.org
Cc: paul.burton@imgtec.com
Link: https://lkml.kernel.org/r/20180228095610.50341-1-nbd@nbd.name
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit f287eb9013ccf199cbfa4eabd80c36fedfc15a73 ]
The error checks on freq for a negative error return always fails because
freq is unsigned and can never be negative. Fix this by making freq a
signed long.
Detected with Coccinelle:
drivers/clocksource/fsl_ftm_timer.c:287:5-9: WARNING: Unsigned expression
compared with zero: freq <= 0
drivers/clocksource/fsl_ftm_timer.c:291:5-9: WARNING: Unsigned expression
compared with zero: freq <= 0
Fixes: 2529c3a33079 ("clocksource: Add Freescale FlexTimer Module (FTM) timer support")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: kernel-janitors@vger.kernel.org
Link: https://lkml.kernel.org/r/20180226113614.3092-1-colin.king@canonical.com
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7407188489c62a7b5694bc75a6db2b82af94c9a5 upstream.
The additional brakects added to tpm_set_next_event's return value
computation causes (int) forced type conversion NOT taking effect, and the
incorrect value return will cause various system timer issue, like RCU
stall etc..
Remove the additional brackets to make sure tpm_set_next_event always
returns correct value.
Fixes: 059ab7b82eec ("clocksource/drivers/imx-tpm: Add imx tpm timer support")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Dong Aisheng <Aisheng.dong@nxp.com>
Cc: stable@vger.kernel.org
Cc: daniel.lezcano@linaro.org
Cc: Linux-imx@nxp.com
Link: https://lkml.kernel.org/r/1524117883-2484-1-git-send-email-Anson.Huang@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e0aeca3d8cbaea514eb98df1149faa918f9ec42d upstream.
The current code hides a couple of bugs:
- The global variable 'clock_event_ddata' is overwritten each time the
init function is invoked.
This is fixed with a kmemdup() instead of assigning the global variable. That
prevents a memory corruption when several timers are defined in the DT.
- The clockevent's event_handler is NULL if the time framework does
not select the clockevent when registering it, this is fine but the init
code generates in any case an interrupt leading to dereference this
NULL pointer.
The stm32 timer works with shadow registers, a mechanism to cache the
registers. When a change is done in one buffered register, we need to
artificially generate an event to force the timer to copy the content
of the register to the shadowed register.
The auto-reload register (ARR) is one of the shadowed register as well as
the prescaler register (PSC), so in order to force the copy, we issue an
event which in turn leads to an interrupt and the NULL dereference.
This is fixed by inverting two lines where we clear the status register
before enabling the update event interrupt.
As this kernel crash is resulting from the combination of these two bugs,
the fixes are grouped into a single patch.
Tested-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1515418139-23276-11-git-send-email-daniel.lezcano@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 21492e1333a0d07af6968667f128e19088cf5ead ]
The ACPI GTDT code validates the CNTFRQ field of each MMIO timer
frame against the CNTFRQ system register of the current CPU, to
ensure that they are equal, which is mandated by the architecture.
However, reading the CNTFRQ field of a frame is not possible until
the RFRQ bit in the frame's CNTACRn register is set, and doing so
before that willl produce the following error:
arch_timer: [Firmware Bug]: CNTFRQ mismatch: frame @ 0x00000000e0be0000: (0x00000000), CPU: (0x0ee6b280)
arch_timer: Disabling MMIO timers due to CNTFRQ mismatch
arch_timer: Failed to initialize memory-mapped timer.
The reason is that the CNTFRQ field is RES0 if access is not enabled.
So move the validation of CNTFRQ into the loop that iterates over the
timers to find the best frame, but defer it until after we have selected
the best frame, which should also have enabled the RFRQ bit.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The interrupt handler mfgpt_tick() is not robust versus spurious interrupts
which happen before the clock event device is registered and fully
initialized.
The reason is that the safe guard against spurious interrupts solely checks
for the clockevents shutdown state, but lacks a check for detached
state. If the interrupt hits while the device is in detached state it
passes the safe guard and dereferences the event handler call back which is
NULL.
Add the missing state check.
Fixes: 8f9327cbb6e8 ("clockevents/drivers/cs5535: Migrate to new 'set-state' interface")
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Kozub <zub@linux.fjfi.cvut.cz>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20171020093103.3317F6004D@linux.fjfi.cvut.cz
|
|
Make this const as it is only used during a copy operation and add
__initconst as this usage is during the initialization phase.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: julia.lawall@lip6.fr
Cc: daniel.lezcano@linaro.org
Link: http://lkml.kernel.org/r/1504030631-10812-1-git-send-email-bhumirks@gmail.com
|
|
gcc-4.6 and older fail to inline integrator_clocksource_init, so they
end up showing a harmless warning:
WARNING: vmlinux.o(.text+0x4aa94c): Section mismatch in reference from the function integrator_clocksource_init() to the function .init.text:clocksource_mmio_init()
The function integrator_clocksource_init() references
the function __init clocksource_mmio_init().
This is often because integrator_clocksource_init lacks a __init
annotation or the annotation of clocksource_mmio_init is wrong.
Add the missing __init annotation that makes it build cleanly with all
compilers.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: http://lkml.kernel.org/r/20170915194310.1170514-1-arnd@arndb.de
|
|
git://git.linux-mips.org/pub/scm/ralf/upstream-linus
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for 4.14 for MIPS; below a summary of
the non-merge commits:
CM:
- Rename mips_cm_base to mips_gcr_base
- Specify register size when generating accessors
- Use BIT/GENMASK for register fields, order & drop shifts
- Add cluster & block args to mips_cm_lock_other()
CPC:
- Use common CPS accessor generation macros
- Use BIT/GENMASK for register fields, order & drop shifts
- Introduce register modify (set/clear/change) accessors
- Use change_*, set_* & clear_* where appropriate
- Add CM/CPC 3.5 register definitions
- Use GlobalNumber macros rather than magic numbers
- Have asm/mips-cps.h include CM & CPC headers
- Cluster support for topology functions
- Detect CPUs in secondary clusters
CPS:
- Read GIC_VL_IDENT directly, not via irqchip driver
DMA:
- Consolidate coherent and non-coherent dma_alloc code
- Don't use dma_cache_sync to implement fd_cacheflush
FPU emulation / FP assist code:
- Another series of 14 commits fixing corner cases such as NaN
propgagation and other special input values.
- Zero bits 32-63 of the result for a CLASS.D instruction.
- Enhanced statics via debugfs
- Do not use bools for arithmetic. GCC 7.1 moans about this.
- Correct user fault_addr type
Generic MIPS:
- Enhancement of stack backtraces
- Cleanup from non-existing options
- Handle non word sized instructions when examining frame
- Fix detection and decoding of ADDIUSP instruction
- Fix decoding of SWSP16 instruction
- Refactor handling of stack pointer in get_frame_info
- Remove unreachable code from force_fcr31_sig()
- Convert to using %pOF instead of full_name
- Remove the R6000 support.
- Move FP code from *_switch.S to *_fpu.S
- Remove unused ST_OFF from r2300_switch.S
- Allow platform to specify multiple its.S files
- Add #includes to various files to ensure code builds reliable and
without warning..
- Remove __invalidate_kernel_vmap_range
- Remove plat_timer_setup
- Declare various variables & functions static
- Abstract CPU core & VP(E) ID access through accessor functions
- Store core & VP IDs in GlobalNumber-style variable
- Unify checks for sibling CPUs
- Add CPU cluster number accessors
- Prevent direct use of generic_defconfig
- Make CONFIG_MIPS_MT_SMP default y
- Add __ioread64_copy
- Remove unnecessary inclusions of linux/irqchip/mips-gic.h
GIC:
- Introduce asm/mips-gic.h with accessor functions
- Use new GIC accessor functions in mips-gic-timer
- Remove counter access functions from irq-mips-gic.c
- Remove gic_read_local_vp_id() from irq-mips-gic.c
- Simplify shared interrupt pending/mask reads in irq-mips-gic.c
- Simplify gic_local_irq_domain_map() in irq-mips-gic.c
- Drop gic_(re)set_mask() functions in irq-mips-gic.c
- Remove gic_set_polarity(), gic_set_trigger(), gic_set_dual_edge(),
gic_map_to_pin() and gic_map_to_vpe() from irq-mips-gic.c.
- Convert remaining shared reg access, local int mask access and
remaining local reg access to new accessors
- Move GIC_LOCAL_INT_* to asm/mips-gic.h
- Remove GIC_CPU_INT* macros from irq-mips-gic.c
- Move various definitions to the driver
- Remove gic_get_usm_range()
- Remove __gic_irq_dispatch() forward declaration
- Remove gic_init()
- Use mips_gic_present() in place of gic_present and remove
gic_present
- Move gic_get_c0_*_int() to asm/mips-gic.h
- Remove linux/irqchip/mips-gic.h
- Inline __gic_init()
- Inline gic_basic_init()
- Make pcpu_masks a per-cpu variable
- Use pcpu_masks to avoid reading GIC_SH_MASK*
- Clean up mti, reserved-cpu-vectors handling
- Use cpumask_first_and() in gic_set_affinity()
- Let the core set struct irq_common_data affinity
microMIPS:
- Fix microMIPS stack unwinding on big endian systems
MIPS-GIC:
- SYNC after enabling GIC region
NUMA:
- Remove the unused parent_node() macro
R6:
- Constify r2_decoder_tables
- Add accessor & bit definitions for GlobalNumber
SMP:
- Constify smp ops
- Allow boot_secondary SMP op to return errors
VDSO:
- Drop gic_get_usm_range() usage
- Avoid use of linux/irqchip/mips-gic.h
Platform changes:
Alchemy:
- Add devboard machine type to cpuinfo
- update cpu feature overrides
- Threaded carddetect irqs for devboards
AR7:
- allow NULL clock for clk_get_rate
BCM63xx:
- Fix ENETDMA_6345_MAXBURST_REG offset
- Allow NULL clock for clk_get_rate
CI20:
- Enable GPIO and RTC drivers in defconfig
- Add ethernet and fixed-regulator nodes to DTS
Generic platform:
- Move Boston and NI 169445 FIT image source to their own files
- Include asm/bootinfo.h for plat_fdt_relocated()
- Include asm/time.h for get_c0_*_int()
- Include asm/bootinfo.h for plat_fdt_relocated()
- Include asm/time.h for get_c0_*_int()
- Allow filtering enabled boards by requirements
- Don't explicitly disable CONFIG_USB_SUPPORT
- Bump default NR_CPUS to 16
JZ4700:
- Probe the jz4740-rtc driver from devicetree
Lantiq:
- Drop check of boot select from the spi-falcon driver.
- Drop check of boot select from the lantiq-flash MTD driver.
- Access boot cause register in the watchdog driver through regmap
- Add device tree binding documentation for the watchdog driver
- Add docs for the RCU DT bindings.
- Convert the fpi bus driver to a platform_driver
- Remove ltq_reset_cause() and ltq_boot_select(
- Switch to a proper reset driver
- Switch to a new drivers/soc GPHY driver
- Add an USB PHY driver for the Lantiq SoCs using the RCU module
- Use of_platform_default_populate instead of __dt_register_buses
- Enable MFD_SYSCON to be able to use it for the RCU MFD
- Replace ltq_boot_select() with dummy implementation.
Loongson 2F:
- Allow NULL clock for clk_get_rate
Malta:
- Use new GIC accessor functions
NI 169445:
- Add support for NI 169445 board.
- Only include in 32r2el kernels
Octeon:
- Add support for watchdog of 78XX SOCs.
- Add support for watchdog of CN68XX SOCs.
- Expose support for mips32r1, mips32r2 and mips64r1
- Enable more drivers in config file
- Add support for accessing the boot vector.
- Remove old boot vector code from watchdog driver
- Define watchdog registers for 70xx, 73xx, 78xx, F75xx.
- Make CSR functions node aware.
- Allow access to CIU3 IRQ domains.
- Misc cleanups in the watchdog driver
Omega2+:
- New board, add support and defconfig
Pistachio:
- Enable Root FS on NFS in defconfig
Ralink:
- Add Mediatek MT7628A SoC
- Allow NULL clock for clk_get_rate
- Explicitly request exclusive reset control in the pci-mt7620 PCI driver.
SEAD3:
- Only include in 32 bit kernels by default
VoCore:
- Add VoCore as a vendor t0 dt-bindings
- Add defconfig file"
* '4.14-features' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (167 commits)
MIPS: Refactor handling of stack pointer in get_frame_info
MIPS: Stacktrace: Fix microMIPS stack unwinding on big endian systems
MIPS: microMIPS: Fix decoding of swsp16 instruction
MIPS: microMIPS: Fix decoding of addiusp instruction
MIPS: microMIPS: Fix detection of addiusp instruction
MIPS: Handle non word sized instructions when examining frame
MIPS: ralink: allow NULL clock for clk_get_rate
MIPS: Loongson 2F: allow NULL clock for clk_get_rate
MIPS: BCM63XX: allow NULL clock for clk_get_rate
MIPS: AR7: allow NULL clock for clk_get_rate
MIPS: BCM63XX: fix ENETDMA_6345_MAXBURST_REG offset
mips: Save all registers when saving the frame
MIPS: Add DWARF unwinding to assembly
MIPS: Make SAVE_SOME more standard
MIPS: Fix issues in backtraces
MIPS: jz4780: DTS: Probe the jz4740-rtc driver from devicetree
MIPS: Ci20: Enable RTC driver
watchdog: octeon-wdt: Add support for 78XX SOCs.
watchdog: octeon-wdt: Add support for cn68XX SOCs.
watchdog: octeon-wdt: File cleaning.
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fixes from Thomas Gleixner:
"A rather small update for the time(r) subsystem:
- A new clocksource driver IMX-TPM
- Minor fixes to the alarmtimer facility
- Device tree cleanups for Renesas drivers
- A new kselftest and fixes for the timer related tests
- Conversion of the clocksource drivers to use %pOF
- Use the proper helpers to access rlimits in the posix-cpu-timer
code"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
alarmtimer: Ensure RTC module is not unloaded
clocksource: Convert to using %pOF instead of full_name
clocksource/drivers/bcm2835: Remove message for a memory allocation failure
devicetree: bindings: Remove deprecated properties
devicetree: bindings: Remove unused 32-bit CMT bindings
devicetree: bindings: Deprecate property, update example
devicetree: bindings: r8a73a4 and R-Car Gen2 CMT bindings
devicetree: bindings: R-Car Gen2 CMT0 and CMT1 bindings
devicetree: bindings: Remove sh7372 CMT binding
clocksource/drivers/imx-tpm: Add imx tpm timer support
dt-bindings: timer: Add nxp tpm timer binding doc
posix-cpu-timers: Use dedicated helper to access rlimit values
alarmtimer: Fix unavailable wake-up source in sysfs
timekeeping: Use proper timekeeper for debug code
kselftests: timers: set-timer-lat: Add one-shot timer test cases
kselftests: timers: set-timer-lat: Tweak reporting when timer fires early
kselftests: timers: freq-step: Fix build warning
kselftests: timers: freq-step: Define ADJ_SETOFFSET if device has older kernel headers
|
|
Now that we have a custom printf format specifier, convert users of
full_name to use %pOF instead. This is preparation to remove storing
of the full path string for each node.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: linux-arm-kernel@lists.infradead.org
Acked-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
Switch from calling functions exported by the GIC interrupt controller
to using new accessors provided by asm/mips-gic.h. This will allow the
counter-handling functionality to be removed from the interrupt
controller driver, where it doesn't really belong, and also allow for
inlining of the accesses to the GIC.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17021/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
The bcm2835_timer_init() function emits an error message in case of a memory
allocation failure. This is pointless as the mm core does that already.
Remove this message.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
IMX Timer/PWM Module (TPM) supports both timer and pwm function while
this patch only adds the timer support. PWM would be added later.
The TPM counter, compare and capture registers are clocked by an
asynchronous clock that can remain enabled in low power modes.
NOTE: We observed in a very small probability, the bus fabric
contention between GPU and A7 may results a few cycles delay
of writing CNT registers which may cause the min_delta event got
missed, so we need add a ETIME check here in case it happened.
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Anson Huang <Anson.Huang@nxp.com>
Cc: Bai Ping <ping.bai@nxp.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
In v4.13, CLKSRC_PISTACHIO can select TIMER_OF on architectures without
GENERIC_CLOCKEVENTS, resulting in a struct clock_event_device missing
some required features and build breakage compiling timer_of.c. One of
the symbols selecting TIMER_OF is CLKSRC_PISTACHIO, so add the
dependency on GENERIC_CLOCKEVENTS.
Thanks to kbuild test robot for finding this error
(https://lkml.org/lkml/2017/7/16/249)
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Suggested-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
The current code checks the return value of the of_io_request_and_map()
function as it was returning a NULL pointer in case of error.
However, it returns an error code encoded in the pointer return value, not a
NULL value. Fix this by checking the returned pointer against IS_ERR() and
return the error with PTR_ERR().
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
Propagate the return values of platform_get_irq and devm_request_irq on
failure.
Cc: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
The loop to find the best memory frame in arch_timer_mem_acpi_init()
initializes the loop counter with itself ('i = i'), which is suspicious
in the first place and pointed out by clang. The loop condition is
'i < timer_count' and a prior for loop exits when 'i' reaches
'timer_count', therefore the second loop is never executed.
Initialize the loop counter with 0 to iterate over all timers, which
supposedly was the intention before the typo monster attacked.
Fixes: c2743a36765d3 ("clocksource: arm_arch_timer: add GTDT support for memory-mapped timer")
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reported-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
Use the new static_branch_enable_cpuslocked() function to switch
the workaround static key on the CPU hotplug path.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Leo Yan <leo.yan@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-arm-kernel@lists.infradead.org
Link: http://lkml.kernel.org/r/20170801080257.5056-5-marc.zyngier@arm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
of_irq_get_byname() may return a negative error number as well as 0 on
failure, while timer_irq_init() only checks for 0, blithely continuing with
the call to request_[percpu_]irq() -- those functions expect *unsigned int*,
so would probably fail anyway when a large IRQ number resulting from a
conversion of a negative error number is passed to them... This, however,
is incorrect behavior -- error number is not IRQ number.
Filter out the negative error numbers, complain, and return them to the
timer_irq_init()'s callers...
Fixes: dc11bae78529 ("clocksource/drivers: Add timer-of common init routine")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: http://lkml.kernel.org/r/20170717180114.678825147@cogentembedded.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"New SoC specific drivers:
- NVIDIA Tegra PM Domain support for newer SoCs (Tegra186 and later)
based on the "BPMP" firmware
- Clocksource and system controller drivers for the newly added
Action Semi platforms (both arm and arm64).
Reset subsystem, merged through arm-soc by tradition:
- New drivers for Altera Stratix10, TI Keystone and Cortina Gemini
SoCs
- Various subsystem-wide cleanups
Updates for existing SoC-specific drivers
- TI GPMC (General Purpose Memory Controller)
- Mediatek "scpsys" system controller support for MT6797
- Broadcom "brcmstb_gisb" bus arbitrer
- ARM SCPI firmware
- Renesas "SYSC" system controller
One more driver update was submitted for the Freescale/NXP DPAA data
path acceleration that has previously been used on PowerPC chips. I
ended up postponing the merge until some API questions for its unusual
MMIO access are resolved"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (35 commits)
clocksource: owl: Add S900 support
clocksource: Add Owl timer
soc: renesas: rcar-sysc: Use GENPD_FLAG_ALWAYS_ON
firmware: tegra: Fix locking bugs in BPMP
soc/tegra: flowctrl: Fix error handling
soc/tegra: bpmp: Implement generic PM domains
soc/tegra: bpmp: Update ABI header
PM / Domains: Allow overriding the ->xlate() callback
soc: brcmstb: enable drivers for ARM64 and BMIPS
soc: renesas: Rework Kconfig and Makefile logic
reset: Add the TI SCI reset driver
dt-bindings: reset: Add TI SCI reset binding
reset: use kref for reference counting
soc: qcom: smsm: Improve error handling, quiesce probe deferral
cpufreq: scpi: use new scpi_ops functions to remove duplicate code
firmware: arm_scpi: add support to populate OPPs and get transition latency
dt-bindings: reset: Add reset manager offsets for Stratix10
memory: omap-gpmc: add error message if bank-width property is absent
memory: omap-gpmc: make dts snippet include semicolon
reset: Add a Gemini reset controller
...
|
|
'gic_clocksource_of_init()'
'clk' is a valid pointer at this point. So calling PTR_ERR on it is
pointess.
Return the error code from 'clk_prepare_enable()' if it fails instead.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
In case of error at init time, rollback iomapping.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
Now that AVR32 is gone, we can use the proper IO accessors that are
correctly handling endianness.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
Phong Hoang
Tom Rix
Keqian Zhu
Yu Kuai
Tianjia Zhang
Serge Semin
Colin Ian King
Marek Szyprowski
Chen-Yu Tsai
Chuhong Yuan
Tao Ren
Sergei Shtylyov
Neil Armstrong
Stuart Menefy
Yangtao Li
Michael Kelley
Keerthy
Alexandre Belloni
Anson Huang
Felix Fietkau
Daniel Lezcano
Ard Biesheuvel
Greg Kroah-Hartman
David Kozub
Bhumika Goyal
Arnd Bergmann
Linus Torvalds
Rob Herring
Paul Burton
Markus Elfring
Dong Aisheng
Ingo Molnar
Matt Redfearn
Dan Carpenter
Gustavo A. R. Silva
Matthias Kaehlcke
Marc Zyngier
Christophe Jaillet
Arvind Yadav
Alexandre Belloni