| Age | Commit message (Collapse) | Author |
|---|
|
commit 956ad9d98b73f59e442cc119c98ba1e04e94fe6d upstream.
As recently reported, some platforms provide a list of power
resources for device power state D3hot, through the _PR3 object,
but they do not provide a list of power resources for device power
state D0.
Among other things, this causes acpi_device_get_power() to return
D3hot as the current state of the device in question if all of the
D3hot power resources are "on", because it sees the power_resources
flag set and calls acpi_power_get_inferred_state() which finds that
D3hot is the shallowest power state with all of the associated power
resources turned "on", so that's what it returns. Moreover, that
value takes precedence over the acpi_dev_pm_explicit_get() return
value, because it means a deeper power state. The device may very
well be in D0 physically at that point, however.
Moreover, the presence of _PR3 without _PR0 for a given device
means that only one D3-level power state can be supported by it.
Namely, because there are no power resources to turn "off" when
transitioning the device from D0 into D3cold (which should be
supported since _PR3 is present), the evaluation of _PS3 should
be sufficient to put it straight into D3cold, but this means that
the effect of turning "on" the _PR3 power resources is unclear,
so it is better to avoid doing that altogether. Consequently,
there is no practical way do distinguish D3cold from D3hot for
the device in question and the power states of it can be labeled
so that D3hot is the deepest supported one (and Linux assumes
that putting a device into D3hot via ACPI may cause power to be
removed from it anyway, for legacy reasons).
To work around the problem described above modify the ACPI
enumeration of devices so that power resources are only used
for device power management if the list of D0 power resources
is not empty and make it mart D3cold as supported only if that
is the case and the D3hot list of power resources is not empty
too.
Fixes: ef85bdbec444 ("ACPI / scan: Consolidate extraction of power resources lists")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=205057
Link: https://lore.kernel.org/linux-acpi/20200603194659.185757-1-hdegoede@redhat.com/
Reported-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: youling257@gmail.com
Cc: 3.10+ <stable@vger.kernel.org> # 3.10+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ea6f3af4c5e63f6981c0b0ab8ebec438e2d5ef40 upstream.
Per the ACPI spec, interrupts in the range [0, 255] may be handled
in AML using individual methods whose naming is based on the format
_Exx or _Lxx, where xx is the hex representation of the interrupt
index.
Add support for this missing feature to our ACPI GED driver.
Cc: v4.9+ <stable@vger.kernel.org> # v4.9+
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4d8be4bc94f74bb7d096e1c2e44457b530d5a170 upstream.
kobject_init_and_add() takes reference even when it fails.
If this function returns an error, kobject_put() must be called to
properly clean up the memory associated with the object. Previous
commit "b8eb718348b8" fixed a similar problem.
Fixes: 158c998ea44b ("ACPI / CPPC: add sysfs support to compute delivered performance")
Signed-off-by: Qiushi Wu <wu000273@umn.edu>
Cc: 4.10+ <stable@vger.kernel.org> # 4.10+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6e6c25283dff866308c87b49434c7dbad4774cc0 upstream.
kobject_init_and_add() takes reference even when it fails.
Thus, when kobject_init_and_add() returns an error,
kobject_put() must be called to properly clean up the kobject.
Fixes: 3f8055c35836 ("ACPI / hotplug: Introduce user space interface for hotplug profiles")
Signed-off-by: Qiushi Wu <wu000273@umn.edu>
Cc: 3.10+ <stable@vger.kernel.org> # 3.10+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 607b9df63057a56f6172d560d5366cca6a030c76 ]
Flushing the EC work while suspended to idle when the EC GPE status
is not set causes some EC wakeup events (notably power button and
lid ones) to be missed after a series of spurious wakeups on the Dell
XPS13 9360 in my office.
If that happens, the machine cannot be woken up from suspend-to-idle
by the power button or lid status change and it needs to be woken up
in some other way (eg. by a key press).
Flushing the EC work only after successful dispatching the EC GPE,
which means that its status has been set, avoids the issue, so change
the code in question accordingly.
Fixes: 7b301750f7f8 ("ACPI: EC: PM: Avoid premature returns from acpi_s2idle_wake()")
Cc: 5.4+ <stable@vger.kernel.org> # 5.4+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Chris Chiu <chiu@endlessm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 7b301750f7f8f6503e11f1af4a03832525f58c66 ]
If the EC GPE status is not set after checking all of the other GPEs,
acpi_s2idle_wake() returns 'false', to indicate that the SCI event
that has just triggered is not a system wakeup one, but it does that
without canceling the pending wakeup and re-arming the SCI for system
wakeup which is a mistake, because it may cause s2idle_loop() to busy
spin until the next valid wakeup event. [If that happens, the first
spurious wakeup is still pending after acpi_s2idle_wake() has
returned, so s2idle_enter() does nothing, acpi_s2idle_wake()
is called again and it sees that the SCI has triggered, but no GPEs
are active, so 'false' is returned again, and so on.]
Fix that by moving all of the GPE checking logic from
acpi_s2idle_wake() to acpi_ec_dispatch_gpe() and making the
latter return 'true' only if a non-EC GPE has triggered and
'false' otherwise, which will cause acpi_s2idle_wake() to
cancel the pending SCI wakeup and re-arm the SCI for system
wakeup regardless of the EC GPE status.
This also addresses a lockup observed on an Elitegroup EF20EA laptop
after attempting to wake it up from suspend-to-idle by a key press.
Fixes: d5406284ff80 ("ACPI: PM: s2idle: Refine active GPEs check")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=207603
Reported-by: Todd Brandt <todd.e.brandt@linux.intel.com>
Fixes: fdde0ff8590b ("ACPI: PM: s2idle: Prevent spurious SCIs from waking up the system")
Link: https://lore.kernel.org/linux-acpi/CAB4CAwdqo7=MvyG_PE+PGVfeA17AHF5i5JucgaKqqMX6mjArbQ@mail.gmail.com/
Reported-by: Chris Chiu <chiu@endlessm.com>
Tested-by: Chris Chiu <chiu@endlessm.com>
Cc: 5.4+ <stable@vger.kernel.org> # 5.4+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 243a98894dc525ad2fbeb608722fcb682be3186d upstream.
Fix a comment in acpi_s2idle_prepare_late() that has become outdated
after commit f0ac20c3f613 ("ACPI: EC: Fix flushing of pending work").
Fixes: f0ac20c3f613 ("ACPI: EC: Fix flushing of pending work")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a9b760b0266f563b4784f695bbd0e717610dc10a upstream.
Transitioned power state logged at the end of setting ACPI power.
However, D3cold won't be in the message because state can only be
D3hot at most.
Use target_state to corretly report when power state is D3cold.
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 9a1ae80412dcaa67a29eecf19de44f32b5f1c357 ]
This is the result of squashing the following ACPICA commit ID's:
6803997e5b4f3635cea6610b51ff69e29d251de3
f31cdf8bfda22fe265c1a176d0e33d311c82a7f7
This change fixes several problems with the support for the
acpi_exec namespace init file (-fi option). Specifically, it
fixes AE_ALREADY_EXISTS errors, as well as various seg faults.
Link: https://github.com/acpica/acpica/commit/f31cdf8b
Link: https://github.com/acpica/acpica/commit/6803997e
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Erik Kaneda <erik.kaneda@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b62c770fee699a137359e1f1da9bf14a7f348567 ]
Tiger Lake's new unique ACPI device IDs for DPTF and fan drivers are not
valid as the IDs are missing 'C'. Fix the IDs by updating them.
After the update, the new IDs should now look like
INT1047 --> INTC1047
INT1040 --> INTC1040
INT1043 --> INTC1043
INT1044 --> INTC1044
Fixes: 55cfe6a5c582 ("ACPI: DPTF: Add Tiger Lake ACPI device IDs")
Fixes: c248dfe7e0ca ("ACPI: fan: Add Tiger Lake ACPI device ID")
Suggested-by: Srinivas Pandruvada <srinivas.pandruvada@intel.com>
Signed-off-by: Gayatri Kammela <gayatri.kammela@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 696ac2e3bf267f5a2b2ed7d34e64131f2287d0ad ]
Similar to commit 0266d81e9bf5 ("acpi/processor: Prevent cpu hotplug
deadlock") except this is for acpi_processor_ffh_cstate_probe():
"The problem is that the work is scheduled on the current CPU from the
hotplug thread associated with that CPU.
It's not required to invoke these functions via the workqueue because
the hotplug thread runs on the target CPU already.
Check whether current is a per cpu thread pinned on the target CPU and
invoke the function directly to avoid the workqueue."
WARNING: possible circular locking dependency detected
------------------------------------------------------
cpuhp/1/15 is trying to acquire lock:
ffffc90003447a28 ((work_completion)(&wfc.work)){+.+.}-{0:0}, at: __flush_work+0x4c6/0x630
but task is already holding lock:
ffffffffafa1c0e8 (cpuidle_lock){+.+.}-{3:3}, at: cpuidle_pause_and_lock+0x17/0x20
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (cpu_hotplug_lock){++++}-{0:0}:
cpus_read_lock+0x3e/0xc0
irq_calc_affinity_vectors+0x5f/0x91
__pci_enable_msix_range+0x10f/0x9a0
pci_alloc_irq_vectors_affinity+0x13e/0x1f0
pci_alloc_irq_vectors_affinity at drivers/pci/msi.c:1208
pqi_ctrl_init+0x72f/0x1618 [smartpqi]
pqi_pci_probe.cold.63+0x882/0x892 [smartpqi]
local_pci_probe+0x7a/0xc0
work_for_cpu_fn+0x2e/0x50
process_one_work+0x57e/0xb90
worker_thread+0x363/0x5b0
kthread+0x1f4/0x220
ret_from_fork+0x27/0x50
-> #0 ((work_completion)(&wfc.work)){+.+.}-{0:0}:
__lock_acquire+0x2244/0x32a0
lock_acquire+0x1a2/0x680
__flush_work+0x4e6/0x630
work_on_cpu+0x114/0x160
acpi_processor_ffh_cstate_probe+0x129/0x250
acpi_processor_evaluate_cst+0x4c8/0x580
acpi_processor_get_power_info+0x86/0x740
acpi_processor_hotplug+0xc3/0x140
acpi_soft_cpu_online+0x102/0x1d0
cpuhp_invoke_callback+0x197/0x1120
cpuhp_thread_fun+0x252/0x2f0
smpboot_thread_fn+0x255/0x440
kthread+0x1f4/0x220
ret_from_fork+0x27/0x50
other info that might help us debug this:
Chain exists of:
(work_completion)(&wfc.work) --> cpuhp_state-up --> cpuidle_lock
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(cpuidle_lock);
lock(cpuhp_state-up);
lock(cpuidle_lock);
lock((work_completion)(&wfc.work));
*** DEADLOCK ***
3 locks held by cpuhp/1/15:
#0: ffffffffaf51ab10 (cpu_hotplug_lock){++++}-{0:0}, at: cpuhp_thread_fun+0x69/0x2f0
#1: ffffffffaf51ad40 (cpuhp_state-up){+.+.}-{0:0}, at: cpuhp_thread_fun+0x69/0x2f0
#2: ffffffffafa1c0e8 (cpuidle_lock){+.+.}-{3:3}, at: cpuidle_pause_and_lock+0x17/0x20
Call Trace:
dump_stack+0xa0/0xea
print_circular_bug.cold.52+0x147/0x14c
check_noncircular+0x295/0x2d0
__lock_acquire+0x2244/0x32a0
lock_acquire+0x1a2/0x680
__flush_work+0x4e6/0x630
work_on_cpu+0x114/0x160
acpi_processor_ffh_cstate_probe+0x129/0x250
acpi_processor_evaluate_cst+0x4c8/0x580
acpi_processor_get_power_info+0x86/0x740
acpi_processor_hotplug+0xc3/0x140
acpi_soft_cpu_online+0x102/0x1d0
cpuhp_invoke_callback+0x197/0x1120
cpuhp_thread_fun+0x252/0x2f0
smpboot_thread_fn+0x255/0x440
kthread+0x1f4/0x220
ret_from_fork+0x27/0x50
Signed-off-by: Qian Cai <cai@lca.pw>
Tested-by: Borislav Petkov <bp@suse.de>
[ rjw: Subject ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 01091c496f920e634ea84b689f480c39016752a8 upstream.
The 'func' variable can come from the user in the __nd_ioctl(). If it's
too high then the (1 << func) shift in acpi_nfit_clear_to_send() is
undefined. In acpi_nfit_ctl() we pass 'func' to test_bit(func, &dsm_mask)
which could result in an out of bounds access.
To fix these issues, I introduced the NVDIMM_CMD_MAX (31) define and
updated nfit_dsm_revid() to use that define as well instead of magic
numbers.
Fixes: 11189c1089da ("acpi/nfit: Fix command-supported detection")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Link: https://lore.kernel.org/r/20200225161927.hvftuq7kjn547fyj@kili.mountain
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit 281e612b4b9587c0c72e30c49ec279587b20da0f which is
commit 65a691f5f8f0bb63d6a82eec7b0ffd193d8d8a5f upstream.
Rafael writes:
It has not been marked for -stable or otherwise requested to be
included AFAICS. Also it depends on other mainline commits that
have not been included into 5.6.5.
Reported-by: Toralf Förster <toralf.foerster@gmx.de>
Reported-by: Rafael J. Wysocki <rafael@kernel.org>
Cc: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d5406284ff803a578ca503373624312770319054 upstream.
The check for any active GPEs added by commit fdde0ff8590b ("ACPI:
PM: s2idle: Prevent spurious SCIs from waking up the system") turns
out to be insufficiently precise to prevent some systems from
resuming prematurely due to a spurious EC wakeup, so refine it
by first checking if any GPEs other than the EC GPE are active
and skipping all of the SCIs coming from the EC that do not produce
any genuine wakeup events after processing.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=206629
Fixes: fdde0ff8590b ("ACPI: PM: s2idle: Prevent spurious SCIs from waking up the system")
Reported-by: Ondřej Caletka <ondrej@caletka.cz>
Tested-by: Ondřej Caletka <ondrej@caletka.cz>
Cc: 5.4+ <stable@vger.kernel.org> # 5.4+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0ce792d660bda990c675eaf14ce09594a9b85cbf upstream.
The check carried out by acpi_any_gpe_status_set() is not precise enough
for the suspend-to-idle implementation in Linux and in some cases it is
necessary make it skip one GPE (specifically, the EC GPE) from the check
to prevent a race condition leading to a premature system resume from
occurring.
For this reason, redefine acpi_any_gpe_status_set() to take the number
of a GPE to skip as an argument.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=206629
Tested-by: Ondřej Caletka <ondrej@caletka.cz>
Cc: 5.4+ <stable@vger.kernel.org> # 5.4+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c823c17a8ea4db4943152388a0beb9a556715716 upstream.
It doesn't really make sense to pass ec->handle of the ECDT EC to
acpi_handle_info(), because it is set to ACPI_ROOT_OBJECT in
acpi_ec_ecdt_probe(), so rework acpi_ec_setup() to avoid using
acpi_handle_info() for printing messages.
First, notice that the "Used as first EC" message is not really
useful, because it is immediately followed by a more meaningful one
from either acpi_ec_ecdt_probe() or acpi_ec_dsdt_probe() (the latter
also includes the EC object path), so drop it altogether.
Second, use pr_info() for printing the EC configuration information.
While at it, make the code in question avoid printing invalid GPE or
IRQ numbers and make it print the GPE/IRQ information only when the
driver is ready to handle events.
Fixes: 72c77b7ea9ce ("ACPI / EC: Cleanup first_ec/boot_ec code")
Fixes: 406857f773b0 ("ACPI: EC: add support for hardware-reduced systems")
Cc: 5.5+ <stable@vger.kernel.org> # 5.5+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 65a691f5f8f0bb63d6a82eec7b0ffd193d8d8a5f ]
The reason for clearing boot_ec_is_ecdt in acpi_ec_add() (if a
PNP0C09 device object matching the ECDT boot EC had been found in
the namespace) was to cause acpi_ec_ecdt_start() to return early,
but since the latter does not look at boot_ec_is_ecdt any more,
acpi_ec_add() need not clear it.
Moreover, doing that may be confusing as it may cause "DSDT" to be
printed instead of "ECDT" in the EC initialization completion
message, so stop doing it.
While at it, split the EC initialization completion message into
two messages, one regarding the boot EC and another one printed
regardless of whether or not the EC at hand is the boot one.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit ddfd9dcf270ce23ed1985b66fcfa163920e2e1b8 upstream.
Since commit fdde0ff8590b ("ACPI: PM: s2idle: Prevent spurious SCIs from
waking up the system") the SCI triggering without there being a wakeup
cause recognized by the ACPI sleep code will no longer wakeup the system.
This works as intended, but this is a problem for devices where the SCI
is shared with another device which is also a wakeup source.
In the past these, from the pov of the ACPI sleep code, spurious SCIs
would still cause a wakeup so the wakeup from the device sharing the
interrupt would actually wakeup the system. This now no longer works.
This is a problem on e.g. Bay Trail-T and Cherry Trail devices where
some peripherals (typically the XHCI controller) can signal a
Power Management Event (PME) to the Power Management Controller (PMC)
to wakeup the system, this uses the same interrupt as the SCI.
These wakeups are handled through a special INT0002 ACPI device which
checks for events in the GPE0a_STS for this and takes care of acking
the PME so that the shared interrupt stops triggering.
The change to the ACPI sleep code to ignore the spurious SCI, causes
the system to no longer wakeup on these PME events. To make things
worse this means that the INT0002 device driver interrupt handler will
no longer run, causing the PME to not get cleared and resulting in the
system hanging. Trying to wakeup the system after such a PME through e.g.
the power button no longer works.
Add an acpi_register_wakeup_handler() function which registers
a handler to be called from acpi_s2idle_wake() and when the handler
returns true, return true from acpi_s2idle_wake().
The INT0002 driver will use this mechanism to check the GPE0a_STS
register from acpi_s2idle_wake() and to tell the system to wakeup
if a PME is signaled in the register.
Fixes: fdde0ff8590b ("ACPI: PM: s2idle: Prevent spurious SCIs from waking up the system")
Cc: 5.4+ <stable@vger.kernel.org> # 5.4+
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit 3f8fd02b1bf1 ("mm/vmalloc: Sync unmappings in
__purge_vmap_area_lazy()") introduced a call to vmalloc_sync_all() in
the vunmap() code-path. While this change was necessary to maintain
correctness on x86-32-pae kernels, it also adds additional cycles for
architectures that don't need it.
Specifically on x86-64 with CONFIG_VMAP_STACK=y some people reported
severe performance regressions in micro-benchmarks because it now also
calls the x86-64 implementation of vmalloc_sync_all() on vunmap(). But
the vmalloc_sync_all() implementation on x86-64 is only needed for newly
created mappings.
To avoid the unnecessary work on x86-64 and to gain the performance
back, split up vmalloc_sync_all() into two functions:
* vmalloc_sync_mappings(), and
* vmalloc_sync_unmappings()
Most call-sites to vmalloc_sync_all() only care about new mappings being
synchronized. The only exception is the new call-site added in the
above mentioned commit.
Shile Zhang directed us to a report of an 80% regression in reaim
throughput.
Fixes: 3f8fd02b1bf1 ("mm/vmalloc: Sync unmappings in __purge_vmap_area_lazy()")
Reported-by: kernel test robot <oliver.sang@intel.com>
Reported-by: Shile Zhang <shile.zhang@linux.alibaba.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Tested-by: Borislav Petkov <bp@suse.de>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> [GHES]
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: <stable@vger.kernel.org>
Link: http://lkml.kernel.org/r/20191009124418.8286-1-joro@8bytes.org
Link: https://lists.01.org/hyperkitty/list/lkp@lists.01.org/thread/4D3JPPHBNOSPFK2KEPC6KGKS6J25AIDB/
Link: http://lkml.kernel.org/r/20191113095530.228959-1-shile.zhang@linux.alibaba.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fixes from Rafael Wysocki:
"Fix a couple of configuration issues in the ACPI watchdog (WDAT)
driver (Mika Westerberg) and make it possible to disable that driver
at boot time in case it still does not work as expected (Jean
Delvare)"
* tag 'acpi-5.6-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: watchdog: Set default timeout in probe
ACPI: watchdog: Fix gas->access_width usage
ACPICA: Introduce ACPI_ACCESS_BYTE_WIDTH() macro
ACPI: watchdog: Allow disabling WDAT at boot
|
|
Commit fdde0ff8590b ("ACPI: PM: s2idle: Prevent spurious SCIs from
waking up the system") overlooked the fact that fixed events can wake
up the system too and broke RTC wakeup from suspend-to-idle as a
result.
Fix this issue by checking the fixed events in acpi_s2idle_wake() in
addition to checking wakeup GPEs and break out of the suspend-to-idle
loop if the status bits of any enabled fixed events are set then.
Fixes: fdde0ff8590b ("ACPI: PM: s2idle: Prevent spurious SCIs from waking up the system")
Reported-and-tested-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: 5.4+ <stable@vger.kernel.org> # 5.4+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
ACPI Generic Address Structure (GAS) access_width field is not in bytes
as the driver seems to expect in few places so fix this by using the
newly introduced macro ACPI_ACCESS_BYTE_WIDTH().
Fixes: b1abf6fc4982 ("ACPI / watchdog: Fix off-by-one error at resource assignment")
Fixes: 058dfc767008 ("ACPI / watchdog: Add support for WDAT hardware watchdog")
Reported-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Cc: 4.16+ <stable@vger.kernel.org> # 4.16+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
If the platform triggers a spurious SCI even though the status bit
is not set for any GPE when the system is suspended to idle, it will
be treated as a genuine wakeup, so avoid that by checking if any GPEs
are active at all before returning 'true' from acpi_s2idle_wake().
Link: https://bugzilla.kernel.org/show_bug.cgi?id=206413
Fixes: 56b991849009 ("PM: sleep: Simplify suspend-to-idle control flow")
Reported-by: Tsuchiya Yuto <kitakar@gmail.com>
Cc: 5.4+ <stable@vger.kernel.org> # 5.4+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Introduce a new helper function, acpi_any_gpe_status_set(), for
checking the status bits of all enabled GPEs in one go.
It is needed to distinguish spurious SCIs from genuine ones when
deciding whether or not to wake up the system from suspend-to-idle.
Cc: 5.4+ <stable@vger.kernel.org> # 5.4+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
It is theoretically possible for the ACPI EC GPE to be set after the
s2idle_ops->wake() called from s2idle_loop() has returned and before
the subsequent pm_wakeup_pending() check is carried out. If that
happens, the resulting wakeup event will cause the system to resume
even though it may be a spurious one.
To avoid that race, first make the ->wake() callback in struct
platform_s2idle_ops return a bool value indicating whether or not
to let the system resume and rearrange s2idle_loop() to use that
value instad of the direct pm_wakeup_pending() call if ->wake() is
present.
Next, rework acpi_s2idle_wake() to process EC events and check
pm_wakeup_pending() before re-arming the SCI for system wakeup
to prevent it from triggering prematurely and add comments to
that function to explain the rationale for the new code flow.
Fixes: 56b991849009 ("PM: sleep: Simplify suspend-to-idle control flow")
Cc: 5.4+ <stable@vger.kernel.org> # 5.4+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Commit 016b87ca5c8c ("ACPI: EC: Rework flushing of pending work")
introduced a subtle bug into the flushing of pending EC work while
suspended to idle, which may cause the EC driver to fail to
re-enable the EC GPE after handling a non-wakeup event (like a
battery status change event, for example).
The problem is that the work item flushed by flush_scheduled_work()
in __acpi_ec_flush_work() may disable the EC GPE and schedule another
work item expected to re-enable it, but that new work item is not
flushed, so __acpi_ec_flush_work() returns with the EC GPE disabled
and the CPU running it goes into an idle state subsequently. If all
of the other CPUs are in idle states at that point, the EC GPE won't
be re-enabled until at least one CPU is woken up by another interrupt
source, so system wakeup events that would normally come from the EC
then don't work.
This is reproducible on a Dell XPS13 9360 in my office which
sometimes stops reacting to power button and lid events (triggered
by the EC on that machine) after switching from AC power to battery
power or vice versa while suspended to idle (each of those switches
causes the EC GPE to trigger for several times in a row, but they
are not system wakeup events).
To avoid this problem, it is necessary to drain the workqueue
entirely in __acpi_ec_flush_work(), but that cannot be done with
respect to system_wq, because work items may be added to it from
other places while __acpi_ec_flush_work() is running. For this
reason, make the EC driver use a dedicated workqueue for EC events
processing (let that workqueue be ordered so that EC events are
processed sequentially) and use drain_workqueue() on it in
__acpi_ec_flush_work().
Fixes: 016b87ca5c8c ("ACPI: EC: Rework flushing of pending work")
Cc: 5.4+ <stable@vger.kernel.org> # 5.4+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
In case the WDAT interface is broken, give the user an option to
ignore it to let a native driver bind to the watchdog device instead.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI updates from Rafael Wysocki:
"Add Hisilicon Hip08-Lite I2C controller clock frequency support to the
ACPI driver for AMD SoCs (APD) and to the Designware I2C driver
(Hanjun Guo)"
* tag 'acpi-5.6-rc1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
i2c: designware: Add ACPI HID for Hisilicon Hip08-Lite I2C controller
ACPI / APD: Add clock frequency for Hisilicon Hip08-Lite I2C controller
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu updates from Joerg Roedel:
- Allow compiling the ARM-SMMU drivers as modules.
- Fixes and cleanups for the ARM-SMMU drivers and io-pgtable code
collected by Will Deacon. The merge-commit (6855d1ba7537) has all the
details.
- Cleanup of the iommu_put_resv_regions() call-backs in various
drivers.
- AMD IOMMU driver cleanups.
- Update for the x2APIC support in the AMD IOMMU driver.
- Preparation patches for Intel VT-d nested mode support.
- RMRR and identity domain handling fixes for the Intel VT-d driver.
- More small fixes and cleanups.
* tag 'iommu-updates-v5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (87 commits)
iommu/amd: Remove the unnecessary assignment
iommu/vt-d: Remove unnecessary WARN_ON_ONCE()
iommu/vt-d: Unnecessary to handle default identity domain
iommu/vt-d: Allow devices with RMRRs to use identity domain
iommu/vt-d: Add RMRR base and end addresses sanity check
iommu/vt-d: Mark firmware tainted if RMRR fails sanity check
iommu/amd: Remove unused struct member
iommu/amd: Replace two consecutive readl calls with one readq
iommu/vt-d: Don't reject Host Bridge due to scope mismatch
PCI/ATS: Add PASID stubs
iommu/arm-smmu-v3: Return -EBUSY when trying to re-add a device
iommu/arm-smmu-v3: Improve add_device() error handling
iommu/arm-smmu-v3: Use WRITE_ONCE() when changing validity of an STE
iommu/arm-smmu-v3: Add second level of context descriptor table
iommu/arm-smmu-v3: Prepare for handling arm_smmu_write_ctx_desc() failure
iommu/arm-smmu-v3: Propagate ssid_bits
iommu/arm-smmu-v3: Add support for Substream IDs
iommu/arm-smmu-v3: Add context descriptor tables allocators
iommu/arm-smmu-v3: Prepare arm_smmu_s1_cfg for SSID support
ACPI/IORT: Parse SSID property of named component node
...
|
|
'PTR_ERR(p) == -E*' is a stronger condition than IS_ERR(p).
Hence, IS_ERR(p) is unneeded.
The semantic patch that generates this commit is as follows:
// <smpl>
@@
expression ptr;
constant error_code;
@@
-IS_ERR(ptr) && (PTR_ERR(ptr) == - error_code)
+PTR_ERR(ptr) == - error_code
// </smpl>
Link: http://lkml.kernel.org/r/20200106045833.1725-1-masahiroy@kernel.org
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Cc: Julia Lawall <julia.lawall@lip6.fr>
Acked-by: Stephen Boyd <sboyd@kernel.org> [drivers/clk/clk.c]
Acked-by: Bartosz Golaszewski <bgolaszewski@baylibre.com> [GPIO]
Acked-by: Wolfram Sang <wsa@the-dreams.de> [drivers/i2c]
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> [acpi/scan.c]
Acked-by: Rob Herring <robh@kernel.org>
Cc: Eric Biggers <ebiggers@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The most notable change is DEFINE_SHOW_ATTRIBUTE macro split in
seq_file.h.
Conversion rule is:
llseek => proc_lseek
unlocked_ioctl => proc_ioctl
xxx => proc_xxx
delete ".owner = THIS_MODULE" line
[akpm@linux-foundation.org: fix drivers/isdn/capi/kcapi_proc.c]
[sfr@canb.auug.org.au: fix kernel/sched/psi.c]
Link: http://lkml.kernel.org/r/20200122180545.36222f50@canb.auug.org.au
Link: http://lkml.kernel.org/r/20191225172546.GB13378@avx2
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
I2C clock frequency of Designware ip for Hisilicon Hip08 Lite
is 125M, use a new ACPI HID to enable it.
Tested-by: Sheng Feng <fengsheng5@huawei.com>
Signed-off-by: Hanjun Guo <guohanjun@huawei.com>
Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Pull updates from Andrew Morton:
"Most of -mm and quite a number of other subsystems: hotfixes, scripts,
ocfs2, misc, lib, binfmt, init, reiserfs, exec, dma-mapping, kcov.
MM is fairly quiet this time. Holidays, I assume"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (118 commits)
kcov: ignore fault-inject and stacktrace
include/linux/io-mapping.h-mapping: use PHYS_PFN() macro in io_mapping_map_atomic_wc()
execve: warn if process starts with executable stack
reiserfs: prevent NULL pointer dereference in reiserfs_insert_item()
init/main.c: fix misleading "This architecture does not have kernel memory protection" message
init/main.c: fix quoted value handling in unknown_bootoption
init/main.c: remove unnecessary repair_env_string in do_initcall_level
init/main.c: log arguments and environment passed to init
fs/binfmt_elf.c: coredump: allow process with empty address space to coredump
fs/binfmt_elf.c: coredump: delete duplicated overflow check
fs/binfmt_elf.c: coredump: allocate core ELF header on stack
fs/binfmt_elf.c: make BAD_ADDR() unlikely
fs/binfmt_elf.c: better codegen around current->mm
fs/binfmt_elf.c: don't copy ELF header around
fs/binfmt_elf.c: fix ->start_code calculation
fs/binfmt_elf.c: smaller code generation around auxv vector fill
lib/find_bit.c: uninline helper _find_next_bit()
lib/find_bit.c: join _find_next_bit{_le}
uapi: rename ext2_swab() to swab() and share globally in swab.h
lib/scatterlist.c: adjust indentation in __sg_alloc_table
...
|
|
This switches the ACPI thermal zone driver to use
celsius_to_deci_kelvin(), deci_kelvin_to_celsius(), and
deci_kelvin_to_millicelsius_with_offset() in <linux/units.h> instead of
helpers in <linux/thermal.h>.
This is preparation for centralizing the kelvin to/from Celsius
conversion helpers in <linux/units.h>.
Link: http://lkml.kernel.org/r/1576386975-7941-3-git-send-email-akinobu.mita@gmail.com
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Sujith Thomas <sujith.thomas@intel.com>
Cc: Darren Hart <dvhart@infradead.org>
Cc: Andy Shevchenko <andy@infradead.org>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Amit Kucheria <amit.kucheria@verdurent.com>
Cc: Jean Delvare <jdelvare@suse.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Keith Busch <kbusch@kernel.org>
Cc: Jens Axboe <axboe@fb.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Sagi Grimberg <sagi@grimberg.me>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Luca Coelho <luciano.coelho@intel.com>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull drm updates from Davbe Airlie:
"This is the main pull request for graphics for 5.6. Usual selection of
changes all over.
I've got one outstanding vmwgfx pull that touches mm so kept it
separate until after all of this lands. I'll try and get it to you
soon after this, but it might be early next week (nothing wrong with
code, just my schedule is messy)
This also hits a lot of fbdev drivers with some cleanups.
Other notables:
- vulkan timeline semaphore support added to syncobjs
- nouveau turing secureboot/graphics support
- Displayport MST display stream compression support
Detailed summary:
uapi:
- dma-buf heaps added (and fixed)
- command line add support for panel oreientation
- command line allow overriding penguin count
drm:
- mipi dsi definition updates
- lockdep annotations for dma_resv
- remove dma-buf kmap/kunmap support
- constify fb_ops in all fbdev drivers
- MST fix for daisy chained hotplug-
- CTA-861-G modes with VIC >= 193 added
- fix drm_panel_of_backlight export
- LVDS decoder support
- more device based logging support
- scanline alighment for dumb buffers
- MST DSC helpers
scheduler:
- documentation fixes
- job distribution improvements
panel:
- Logic PD type 28 panel support
- Jimax8729d MIPI-DSI
- igenic JZ4770
- generic DSI devicetree bindings
- sony acx424AKP panel
- Leadtek LTK500HD1829
- xinpeng XPP055C272
- AUO B116XAK01
- GiantPlus GPM940B0
- BOE NV140FHM-N49
- Satoz SAT050AT40H12R2
- Sharp LS020B1DD01D panels.
ttm:
- use blocking WW lock
i915:
- hw/uapi state separation
- Lock annotation improvements
- selftest improvements
- ICL/TGL DSI VDSC support
- VBT parsing improvments
- Display refactoring
- DSI updates + fixes
- HDCP 2.2 for CFL
- CML PCI ID fixes
- GLK+ fbc fix
- PSR fixes
- GEN/GT refactor improvments
- DP MST fixes
- switch context id alloc to xarray
- workaround updates
- LMEM debugfs support
- tiled monitor fixes
- ICL+ clock gating programming removed
- DP MST disable sequence fixed
- LMEM discontiguous object maps
- prefaulting for discontiguous objects
- use LMEM for dumb buffers if possible
- add LMEM mmap support
amdgpu:
- enable sync object timelines for vulkan
- MST atomic routines
- enable MST DSC support
- add DMCUB display microengine support
- DC OEM i2c support
- Renoir DC fixes
- Initial HDCP 2.x support
- BACO support for Arcturus
- Use BACO for runtime PM power save
- gfxoff on navi10
- gfx10 golden updates and fixes
- DCN support on POWER
- GFXOFF for raven1 refresh
- MM engine idle handlers cleanup
- 10bpc EDP panel fixes
- renoir watermark fixes
- SR-IOV fixes
- Arcturus VCN fixes
- GDDR6 training fixes
- freesync fixes
- Pollock support
amdkfd:
- unify more codepath with amdgpu
- use KIQ to setup HIQ rather than MMIO
radeon:
- fix vma fault handler race
- PPC DMA fix
- register check fixes for r100/r200
nouveau:
- mmap_sem vs dma_resv fix
- rewrite the ACR secure boot code for Turing
- TU10x graphics engine support (TU11x pending)
- Page kind mapping for turing
- 10-bit LUT support
- GP10B Tegra fixes
- HD audio regression fix
hisilicon/hibmc:
- use generic fbdev code and helpers
rockchip:
- dsi/px30 support
virtio:
- fb damage support
- static some functions
vc4:
- use dma_resv lock wrappers
msm:
- use dma_resv lock wrappers
- sc7180 display + DSI support
- a618 support
- UBWC support improvements
vmwgfx:
- updates + new logging uapi
exynos:
- enable/disable callback cleanups
etnaviv:
- use dma_resv lock wrappers
atmel-hlcdc:
- clock fixes
mediatek:
- cmdq support
- non-smooth cursor fixes
- ctm property support
sun4i:
- suspend support
- A64 mipi dsi support
rcar-du:
- Color management module support
- LVDS encoder dual-link support
- R8A77980 support
analogic:
- add support for an6345
ast:
- atomic modeset support
- primary plane garbage fix
arcgpu:
- fixes for fourcc handling
tegra:
- minor fixes and improvments
mcde:
- vblank support
meson:
- OSD1 plane AFBC commit
gma500:
- add pageflip support
- reomve global drm_dev
komeda:
- tweak debugfs output
- d32 support
- runtime PM suppotr
udl:
- use generic shmem helpers
- cleanup and fixes"
* tag 'drm-next-2020-01-30' of git://anongit.freedesktop.org/drm/drm: (1998 commits)
drm/nouveau/fb/gp102-: allow module to load even when scrubber binary is missing
drm/nouveau/acr: return error when registering LSF if ACR not supported
drm/nouveau/disp/gv100-: not all channel types support reporting error codes
drm/nouveau/disp/nv50-: prevent oops when no channel method map provided
drm/nouveau: support synchronous pushbuf submission
drm/nouveau: signal pending fences when channel has been killed
drm/nouveau: reject attempts to submit to dead channels
drm/nouveau: zero vma pointer even if we only unreference it rather than free
drm/nouveau: Add HD-audio component notifier support
drm/nouveau: fix build error without CONFIG_IOMMU_API
drm/nouveau/kms/nv04: remove set but not used variable 'width'
drm/nouveau/kms/nv50: remove set but not unused variable 'nv_connector'
drm/nouveau/mmu: fix comptag memory leak
drm/nouveau/gr/gp10b: Use gp100_grctx and gp100_gr_zbc
drm/nouveau/pmu/gm20b,gp10b: Fix Falcon bootstrapping
drm/exynos: Rename Exynos to lowercase
drm/exynos: change callback names
drm/mst: Don't do atomic checks over disabled managers
drm/amdgpu: add the lost mutex_init back
drm/amd/display: skip opp blank or unblank if test pattern enabled
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull header cleanup from Ingo Molnar:
"This is a treewide cleanup, mostly (but not exclusively) with x86
impact, which breaks implicit dependencies on the asm/realtime.h
header and finally removes it from asm/acpi.h"
* 'core-headers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/ACPI/sleep: Move acpi_get_wakeup_address() into sleep.c, remove <asm/realmode.h> from <asm/acpi.h>
ACPI/sleep: Convert acpi_wakeup_address into a function
x86/ACPI/sleep: Remove an unnecessary include of asm/realmode.h
ASoC: Intel: Skylake: Explicitly include linux/io.h for virt_to_phys()
vmw_balloon: Explicitly include linux/io.h for virt_to_phys()
virt: vbox: Explicitly include linux/io.h to pick up various defs
efi/capsule-loader: Explicitly include linux/io.h for page_to_phys()
perf/x86/intel: Explicitly include asm/io.h to use virt_to_phys()
x86/kprobes: Explicitly include vmalloc.h for set_vm_flush_reset_perms()
x86/ftrace: Explicitly include vmalloc.h for set_vm_flush_reset_perms()
x86/boot: Explicitly include realmode.h to handle RM reservations
x86/efi: Explicitly include realmode.h to handle RM trampoline quirk
x86/platform/intel/quark: Explicitly include linux/io.h for virt_to_phys()
x86/setup: Enhance the comments
x86/setup: Clean up the header portion of setup.c
|
|
Pull ioremap updates from Christoph Hellwig:
"Remove the ioremap_nocache API (plus wrappers) that are always
identical to ioremap"
* tag 'ioremap-5.6' of git://git.infradead.org/users/hch/ioremap:
remove ioremap_nocache and devm_ioremap_nocache
MIPS: define ioremap_nocache to ioremap
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI updates from Rafael Wysocki:
"These update the ACPICA code in the kernel to the most recent upstream
revision (20200110), add new hardware support to a handful of ACPI
drivers, make the ACPI fan driver expose power states information for
fans, add some more quirks, fix bugs and clean up assorted things.
Specifics:
- Update the ACPICA code in the kernel to upstream revision 20200110
including:
- Update of copyright notices to 2020 (Bob Moore).
- Dispatcher fix to always generate buffer objects for the ASL
create_field() operator (Maximilian Luz).
- Debugger cleanup (Colin Ian King).
- Disassembler change to create buffer fields in
ACPI_PARSE_LOAD_PASS1 (Erik Kaneda).
- UNIX line ending support for non-windows builds in acpisrc (Erik
Kaneda).
- Update the list of ACPICA maintainers (Rafael Wysocki).
- Add Intel Tiger Lake ACPI device IDs to the ACPI DPTF, ACPI fan,
int340x_thermal and intel-hid drivers (Gayatri Kammela).
- Make the ACPI fan driver create additional sysfs attributes to
expose power states information for fans (Srinivas Pandruvada).
- Fix up the ACPI battery driver to deal with unexpected battery
capacity information in a better way (Hans de Goede).
- Add ACPI backlight quirks for Lenovo E41-25/45 and MSI MS-7721
boards (Aaron Ma, Hans de Goede).
- Add DMI quirk for Razer Blade Stealth 13 late 2019 lid switch to
the ACPI button driver (Jason Ekstrand).
- Drop TIMER_DEFERRABLE from the GHES polling mode timer function
flags to make it run precisely at the configured time (Bhaskar
Upadhaya).
- Fix race condition related to the reference counting of query
handlers in the ACPI EC driver (Rafael Wysocki).
- Fix ACPI tools build issue (Zhengyuan Liu).
- Replace dma_request_slave_channel() with dma_request_chan() in the
firmware guide documentation for ACPI (Peter Ujfalusi).
- Fix typo in a comment and clean up function parameter data type
inconsistencies (Kacper Piwiński, Tian Tao)"
* tag 'acpi-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (25 commits)
ACPICA: Update version to 20200110
ACPICA: All acpica: Update copyrights to 2020 Including tool signons.
apei/ghes: Do not delay GHES polling
ACPI: button: Add DMI quirk for Razer Blade Stealth 13 late 2019 lid switch
ACPI: PPTT: Consistently use unsigned int as parameter type
ACPI: EC: Reference count query handlers under lock
ACPICA: Update the list of maintainers
ACPICA: Update version to 20191213
ACPICA: Dispatcher: always generate buffer objects for ASL create_field() operator
ACPICA: acpisrc: add unix line ending support for non-windows build
ACPICA: Disassembler: create buffer fields in ACPI_PARSE_LOAD_PASS1
ACPICA: debugger: fix spelling mistake "adress" -> "address"
ACPI: video: Do not export a non working backlight interface on MSI MS-7721 boards
docs: firmware-guide: ACPI: Replace dma_request_slave_channel() with dma_request_chan()
thermal: int340x_thermal: Add Tiger Lake ACPI device IDs
platform/x86: intel-hid: Add Tiger Lake ACPI device ID
ACPI: fan: Add Tiger Lake ACPI device ID
ACPI: DPTF: Add Tiger Lake ACPI device IDs
ACPI: fan: Expose fan performance state information
tools/power/acpi: fix compilation error
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These add ACPI support to the intel_idle driver along with an admin
guide document for it, add support for CPR (Core Power Reduction) to
the AVS (Adaptive Voltage Scaling) subsystem, add new hardware support
in a few places, add some new sysfs attributes, debugfs files and
tracepoints, fix bugs and clean up a bunch of things all over.
Specifics:
- Update the ACPI processor driver in order to export
acpi_processor_evaluate_cst() to the code outside of it, add ACPI
support to the intel_idle driver based on that and clean up that
driver somewhat (Rafael Wysocki).
- Add an admin guide document for the intel_idle driver (Rafael
Wysocki).
- Clean up cpuidle core and drivers, enable compilation testing for
some of them (Benjamin Gaignard, Krzysztof Kozlowski, Rafael
Wysocki, Yangtao Li).
- Fix reference counting of OPP (operating performance points) table
structures (Viresh Kumar).
- Add support for CPR (Core Power Reduction) to the AVS (Adaptive
Voltage Scaling) subsystem (Niklas Cassel, Colin Ian King,
YueHaibing).
- Add support for TigerLake Mobile and JasperLake to the Intel RAPL
power capping driver (Zhang Rui).
- Update cpufreq drivers:
- Add i.MX8MP support to imx-cpufreq-dt (Anson Huang).
- Fix usage of a macro in loongson2_cpufreq (Alexandre Oliva).
- Fix cpufreq policy reference counting issues in s3c and
brcmstb-avs (chenqiwu).
- Fix ACPI table reference counting issue and HiSilicon quirk
handling in the CPPC driver (Hanjun Guo).
- Clean up spelling mistake in intel_pstate (Harry Pan).
- Convert the kirkwood and tegra186 drivers to using
devm_platform_ioremap_resource() (Yangtao Li).
- Update devfreq core:
- Add 'name' sysfs attribute for devfreq devices (Chanwoo Choi).
- Clean up the handing of transition statistics and allow them to
be reset by writing 0 to the 'trans_stat' devfreq device
attribute in sysfs (Kamil Konieczny).
- Add 'devfreq_summary' to debugfs (Chanwoo Choi).
- Clean up kerneldoc comments and Kconfig indentation (Krzysztof
Kozlowski, Randy Dunlap).
- Update devfreq drivers:
- Add dynamic scaling for the imx8m DDR controller and clean up
imx8m-ddrc (Leonard Crestez, YueHaibing).
- Fix DT node reference counting and nitialization error code path
in rk3399_dmc and add COMPILE_TEST and HAVE_ARM_SMCCC dependency
for it (Chanwoo Choi, Yangtao Li).
- Fix DT node reference counting in rockchip-dfi and make it use
devm_platform_ioremap_resource() (Yangtao Li).
- Fix excessive stack usage in exynos-ppmu (Arnd Bergmann).
- Fix initialization error code paths in exynos-bus (Yangtao Li).
- Clean up exynos-bus and exynos somewhat (Artur Świgoń, Krzysztof
Kozlowski).
- Add tracepoints for tracking usage_count updates unrelated to
status changes in PM-runtime (Michał Mirosław).
- Add sysfs attribute to control the "sync on suspend" behavior
during system-wide suspend (Jonas Meurer).
- Switch system-wide suspend tests over to 64-bit time (Alexandre
Belloni).
- Make wakeup sources statistics in debugfs cover deleted ones which
used to be the case some time ago (zhuguangqing).
- Clean up computations carried out during hibernation, update
messages related to hibernation and fix a spelling mistake in one
of them (Wen Yang, Luigi Semenzato, Colin Ian King).
- Add mailmap entry for maintainer e-mail address that has not been
functional for several years (Rafael Wysocki)"
* tag 'pm-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (83 commits)
cpufreq: loongson2_cpufreq: adjust cpufreq uses of LOONGSON_CHIPCFG
intel_idle: Clean up irtl_2_usec()
intel_idle: Move 3 functions closer to their callers
intel_idle: Annotate initialization code and data structures
intel_idle: Move and clean up intel_idle_cpuidle_devices_uninit()
intel_idle: Rearrange intel_idle_cpuidle_driver_init()
intel_idle: Clean up NULL pointer check in intel_idle_init()
intel_idle: Fold intel_idle_probe() into intel_idle_init()
intel_idle: Eliminate __setup_broadcast_timer()
cpuidle: fix cpuidle_find_deepest_state() kerneldoc warnings
cpuidle: sysfs: fix warnings when compiling with W=1
cpuidle: coupled: fix warnings when compiling with W=1
cpufreq: brcmstb-avs: fix imbalance of cpufreq policy refcount
PM: suspend: Add sysfs attribute to control the "sync on suspend" behavior
PM / devfreq: Add debugfs support with devfreq_summary file
Documentation: admin-guide: PM: Add intel_idle document
cpuidle: arm: Enable compile testing for some of drivers
PM-runtime: add tracepoints for usage_count changes
cpufreq: intel_pstate: fix spelling mistake: "Whethet" -> "Whether"
PM: hibernate: fix spelling mistake "shapshot" -> "snapshot"
...
|
|
'acpi-tools'
* acpi-tables:
ACPI: PPTT: Consistently use unsigned int as parameter type
* acpi-button:
ACPI: button: Add DMI quirk for Razer Blade Stealth 13 late 2019 lid switch
* acpi-ec:
ACPI: EC: Reference count query handlers under lock
* acpi-doc:
docs: firmware-guide: ACPI: Replace dma_request_slave_channel() with dma_request_chan()
* acpi-tools:
tools/power/acpi: fix compilation error
|
|
* acpi-battery:
ACPI / battery: Deal better with neither design nor full capacity not being reported
ACPI / battery: Use design-cap for capacity calculations if full-cap is not available
ACPI / battery: Deal with design or full capacity being reported as -1
* acpi-video:
ACPI: video: Do not export a non working backlight interface on MSI MS-7721 boards
ACPI: video: Use native backlight on Lenovo E41-25/45
ACPI: video: fix typo in comment
* acpi-fan:
ACPI: fan: Expose fan performance state information
* acpi-drivers:
thermal: int340x_thermal: Add Tiger Lake ACPI device IDs
platform/x86: intel-hid: Add Tiger Lake ACPI device ID
ACPI: fan: Add Tiger Lake ACPI device ID
ACPI: DPTF: Add Tiger Lake ACPI device IDs
|
|
* acpica:
ACPICA: Update version to 20200110
ACPICA: All acpica: Update copyrights to 2020 Including tool signons.
ACPICA: Update the list of maintainers
ACPICA: Update version to 20191213
ACPICA: Dispatcher: always generate buffer objects for ASL create_field() operator
ACPICA: acpisrc: add unix line ending support for non-windows build
ACPICA: Disassembler: create buffer fields in ACPI_PARSE_LOAD_PASS1
ACPICA: debugger: fix spelling mistake "adress" -> "address"
|
|
The IORT specification [0] (Section 3, table 4, page 9) defines the
'Number of IDs' as 'The number of IDs in the range minus one'.
However, the IORT ID mapping function iort_id_map() treats the 'Number
of IDs' field as if it were the full IDs mapping count, with the
following check in place to detect out of boundary input IDs:
InputID >= Input base + Number of IDs
This check is flawed in that it considers the 'Number of IDs' field as
the full number of IDs mapping and disregards the 'minus one' from
the IDs count.
The correct check in iort_id_map() should be implemented as:
InputID > Input base + Number of IDs
this implements the specification correctly but unfortunately it breaks
existing firmwares that erroneously set the 'Number of IDs' as the full
IDs mapping count rather than IDs mapping count minus one.
e.g.
PCI hostbridge mapping entry 1:
Input base: 0x1000
ID Count: 0x100
Output base: 0x1000
Output reference: 0xC4 //ITS reference
PCI hostbridge mapping entry 2:
Input base: 0x1100
ID Count: 0x100
Output base: 0x2000
Output reference: 0xD4 //ITS reference
Two mapping entries which the second entry's Input base = the first
entry's Input base + ID count, so for InputID 0x1100 and with the
correct InputID check in place in iort_id_map() the kernel would map
the InputID to ITS 0xC4 not 0xD4 as it would be expected.
Therefore, to keep supporting existing flawed firmwares, introduce a
workaround that instructs the kernel to use the old InputID range check
logic in iort_id_map(), so that we can support both firmwares written
with the flawed 'Number of IDs' logic and the correct one as defined in
the specifications.
[0]: http://infocenter.arm.com/help/topic/com.arm.doc.den0049d/DEN0049D_IO_Remapping_Table.pdf
Reported-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Link: https://lore.kernel.org/linux-acpi/20191215203303.29811-1-pankaj.bansal@nxp.com/
Signed-off-by: Hanjun Guo <guohanjun@huawei.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Pankaj Bansal <pankaj.bansal@nxp.com>
Cc: Will Deacon <will@kernel.org>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
|
|
Named component nodes in the IORT tables describe the number of
Substream ID bits (aka. PASID) supported by the device. Propagate this
value to the fwspec structure in order to enable PASID for platform
devices.
Acked-by: Hanjun Guo <guohanjun@huawei.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Signed-off-by: Will Deacon <will@kernel.org>
|
|
ACPICA commit 8b9c69d0984067051ffbe8526f871448ead6a26b
Link: https://github.com/acpica/acpica/commit/8b9c69d0
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Erik Kaneda <erik.kaneda@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Currently, the ghes_poll_func() timer callback is registered with the
TIMER_DEFERRABLE flag. Thus, it is run when the CPU eventually wakes
up together with a subsequent non-deferrable timer and not at the precisely
configured polling interval.
For polling mode, the polling interval configured by firmware should not
be exceeded according to the ACPI spec 6.3, Table 18-394. The definition
of the polling interval is:
"Indicates the poll interval in milliseconds OSPM should use to
periodically check the error source for the presence of an error
condition."
If this interval is extended due to the timer callback deferring, error
records can get lost. Which we are observing on our ThunderX2 platforms.
Therefore, remove the TIMER_DEFERRABLE flag so that the timer callback
executes at the precise interval.
Signed-off-by: Bhaskar Upadhaya <bupadhaya@marvell.com>
[ bp: Subject & changelog ]
Acked-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Running evemu-record on the lid switch event shows that the lid reports
the first "close" but then never reports an "open". This causes systemd
to continuously re-suspend the laptop every 30s. Resetting the _LID to
"open" fixes the issue.
Signed-off-by: Jason Ekstrand <jason@jlekstrand.net>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The fourth parameter 'level' of function 'acpi_find_cache_level()' is
a signed interger, but its caller 'acpi_find_cache_node()' passes that
parameter an unsigned interger.
Make the paramter type inconsistency go away.
Signed-off-by: Tian Tao <tiantao6@huawei.com>
Signed-off-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
[ rjw: Subject/changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
ioremap has provided non-cached semantics by default since the Linux 2.6
days, so remove the additional ioremap_nocache interface.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
|
|
There is a race condition in acpi_ec_get_query_handler()
theoretically allowing query handlers to go away before refernce
counting them.
In order to avoid it, call kref_get() on query handlers under
ec->mutex.
Also simplify the code a bit while at it.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
Rafael J. Wysocki
Ard Biesheuvel
Qiushi Wu
Kai-Heng Feng
Bob Moore
Gayatri Kammela
Qian Cai
Dan Carpenter
Greg Kroah-Hartman
Hans de Goede
Joerg Roedel
Linus Torvalds
Mika Westerberg
Jean Delvare
Masahiro Yamada
Alexey Dobriyan
Hanjun Guo
Akinobu Mita
Jean-Philippe Brucker
Bhaskar Upadhaya
Jason Ekstrand
Tian Tao
Christoph Hellwig