| Age | Commit message (Collapse) | Author |
|---|
|
commit 6e61dc9da0b7a0d91d57c2e20b5ea4fd2d4e7e53 upstream.
The JIT uses agfi for subtracting constants, but -(-0x80000000) cannot
be represented as a 32-bit signed binary integer. Fix by using algfi in
this particular case.
Reported-by: Johan Almbladh <johan.almbladh@anyfinetworks.com>
Fixes: 054623105728 ("s390/bpf: Add s390x eBPF JIT compiler backend")
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit db7bee653859ef7179be933e7d1384644f795f26 upstream.
Currently the JIT completely removes things like `reg32 += 0`,
however, the BPF_ALU semantics requires the target register to be
zero-extended in such cases.
Fix by optimizing out only the arithmetic operation, but not the
subsequent zero-extension.
Reported-by: Johan Almbladh <johan.almbladh@anyfinetworks.com>
Fixes: 054623105728 ("s390/bpf: Add s390x eBPF JIT compiler backend")
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 6b5ff0405e4190f23780362ea324b250bc495683 ]
0day bot reports a build error:
ERROR: modpost: "clear_user_page" [drivers/media/v4l2-core/videobuf-dma-sg.ko] undefined!
so export it in arch/arc/ to fix the build error.
In most ARCHes, clear_user_page() is a macro. OTOH, in a few
ARCHes it is a function and needs to be exported.
PowerPC exported it in 2004. It looks like nds32 and nios2
still need to have it exported.
Fixes: 4102b53392d63 ("ARC: [mm] Aliasing VIPT dcache support 2/4")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: linux-snps-arc@lists.infradead.org
Signed-off-by: Vineet Gupta <vgupta@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 267cdfa21385d78c794768233678756e32b39ead upstream.
POWER9 DD2.2 and 2.3 hardware implements a "fake-suspend" mode where
certain TM instructions executed in HV=0 mode cause softpatch interrupts
so the hypervisor can emulate them and prevent problematic processor
conditions. In this fake-suspend mode, the treclaim. instruction does
not modify registers.
Unfortunately the rfscv instruction executed by the guest do not
generate softpatch interrupts, which can cause the hypervisor to lose
track of the fake-suspend mode, and it can execute this treclaim. while
not in fake-suspend mode. This modifies GPRs and crashes the hypervisor.
It's not trivial to disable scv in the guest with HFSCR now, because
they assume a POWER9 has scv available. So this fix saves and restores
checkpointed registers across the treclaim.
Fixes: 7854f7545bff ("KVM: PPC: Book3S: Rework TM save/restore code and make it C-callable")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210908101718.118522-2-npiggin@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 34b1999da935a33be6239226bfa6cd4f704c5c88 upstream.
Jiri Olsa reported a fault when running:
# cat /proc/kallsyms | grep ksys_read
ffffffff8136d580 T ksys_read
# objdump -d --start-address=0xffffffff8136d580 --stop-address=0xffffffff8136d590 /proc/kcore
/proc/kcore: file format elf64-x86-64
Segmentation fault
general protection fault, probably for non-canonical address 0xf887ffcbff000: 0000 [#1] SMP PTI
CPU: 12 PID: 1079 Comm: objdump Not tainted 5.14.0-rc5qemu+ #508
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.14.0-4.fc34 04/01/2014
RIP: 0010:kern_addr_valid
Call Trace:
read_kcore
? rcu_read_lock_sched_held
? rcu_read_lock_sched_held
? rcu_read_lock_sched_held
? trace_hardirqs_on
? rcu_read_lock_sched_held
? lock_acquire
? lock_acquire
? rcu_read_lock_sched_held
? lock_acquire
? rcu_read_lock_sched_held
? rcu_read_lock_sched_held
? rcu_read_lock_sched_held
? lock_release
? _raw_spin_unlock
? __handle_mm_fault
? rcu_read_lock_sched_held
? lock_acquire
? rcu_read_lock_sched_held
? lock_release
proc_reg_read
? vfs_read
vfs_read
ksys_read
do_syscall_64
entry_SYSCALL_64_after_hwframe
The fault happens because kern_addr_valid() dereferences existent but not
present PMD in the high kernel mappings.
Such PMDs are created when free_kernel_image_pages() frees regions larger
than 2Mb. In this case, a part of the freed memory is mapped with PMDs and
the set_memory_np_noalias() -> ... -> __change_page_attr() sequence will
mark the PMD as not present rather than wipe it completely.
Have kern_addr_valid() check whether higher level page table entries are
present before trying to dereference them to fix this issue and to avoid
similar issues in the future.
Stable backporting note:
------------------------
Note that the stable marking is for all active stable branches because
there could be cases where pagetable entries exist but are not valid -
see 9a14aefc1d28 ("x86: cpa, fix lookup_address"), for example. So make
sure to be on the safe side here and use pXY_present() accessors rather
than pXY_none() which could #GP when accessing pages in the direct map.
Also see:
c40a56a7818c ("x86/mm/init: Remove freed kernel image areas from alias mapping")
for more info.
Reported-by: Jiri Olsa <jolsa@redhat.com>
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: David Hildenbrand <david@redhat.com>
Acked-by: Dave Hansen <dave.hansen@intel.com>
Tested-by: Jiri Olsa <jolsa@redhat.com>
Cc: <stable@vger.kernel.org> # 4.4+
Link: https://lkml.kernel.org/r/20210819132717.19358-1-rppt@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e35ac9d0b56e9efefaeeb84b635ea26c2839ea86 upstream.
When we need a buffer for SVE register state we call sve_alloc() to make
sure that one is there. In order to avoid repeated allocations and frees
we keep the buffer around unless we change vector length and just memset()
it to ensure a clean register state. The function that deals with this
takes the task to operate on as an argument, however in the case where we
do a memset() we initialise using the SVE state size for the current task
rather than the task passed as an argument.
This is only an issue in the case where we are setting the register state
for a task via ptrace and the task being configured has a different vector
length to the task tracing it. In the case where the buffer is larger in
the traced process we will leak old state from the traced process to
itself, in the case where the buffer is smaller in the traced process we
will overflow the buffer and corrupt memory.
Fixes: bc0ee4760364 ("arm64/sve: Core task context handling")
Cc: <stable@vger.kernel.org> # 4.15.x
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210909165356.10675-1-broonie@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f68aa100d815b5b4467fd1c3abbe3b99d65fd028 upstream.
A Xen PV guest doesn't have a legacy RTC device, so reset the legacy
RTC flag. Otherwise the following WARN splat will occur at boot:
[ 1.333404] WARNING: CPU: 1 PID: 1 at /home/gross/linux/head/drivers/rtc/rtc-mc146818-lib.c:25 mc146818_get_time+0x1be/0x210
[ 1.333404] Modules linked in:
[ 1.333404] CPU: 1 PID: 1 Comm: swapper/0 Tainted: G W 5.14.0-rc7-default+ #282
[ 1.333404] RIP: e030:mc146818_get_time+0x1be/0x210
[ 1.333404] Code: c0 64 01 c5 83 fd 45 89 6b 14 7f 06 83 c5 64 89 6b 14 41 83 ec 01 b8 02 00 00 00 44 89 63 10 5b 5d 41 5c 41 5d 41 5e 41 5f c3 <0f> 0b 48 c7 c7 30 0e ef 82 4c 89 e6 e8 71 2a 24 00 48 c7 c0 ff ff
[ 1.333404] RSP: e02b:ffffc90040093df8 EFLAGS: 00010002
[ 1.333404] RAX: 00000000000000ff RBX: ffffc90040093e34 RCX: 0000000000000000
[ 1.333404] RDX: 0000000000000001 RSI: 0000000000000000 RDI: 000000000000000d
[ 1.333404] RBP: ffffffff82ef0e30 R08: ffff888005013e60 R09: 0000000000000000
[ 1.333404] R10: ffffffff82373e9b R11: 0000000000033080 R12: 0000000000000200
[ 1.333404] R13: 0000000000000000 R14: 0000000000000002 R15: ffffffff82cdc6d4
[ 1.333404] FS: 0000000000000000(0000) GS:ffff88807d440000(0000) knlGS:0000000000000000
[ 1.333404] CS: 10000e030 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 1.333404] CR2: 0000000000000000 CR3: 000000000260a000 CR4: 0000000000050660
[ 1.333404] Call Trace:
[ 1.333404] ? wakeup_sources_sysfs_init+0x30/0x30
[ 1.333404] ? rdinit_setup+0x2b/0x2b
[ 1.333404] early_resume_init+0x23/0xa4
[ 1.333404] ? cn_proc_init+0x36/0x36
[ 1.333404] do_one_initcall+0x3e/0x200
[ 1.333404] kernel_init_freeable+0x232/0x28e
[ 1.333404] ? rest_init+0xd0/0xd0
[ 1.333404] kernel_init+0x16/0x120
[ 1.333404] ret_from_fork+0x1f/0x30
Cc: <stable@vger.kernel.org>
Fixes: 8d152e7a5c7537 ("x86/rtc: Replace paravirt rtc check with platform legacy quirk")
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Link: https://lore.kernel.org/r/20210903084937.19392-3-jgross@suse.com
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 93ebb6828723b8aef114415c4dc3518342f7dcad upstream.
Since commit 903cd0f315fe ("swiotlb: Use is_swiotlb_force_bounce for
swiotlb data bouncing") if code sets swiotlb_force it needs to do so
before the swiotlb is initialised. Otherwise
io_tlb_default_mem->force_bounce will not get set to true, and devices
that use (the default) swiotlb will not bounce despite switolb_force
having the value of SWIOTLB_FORCE.
Let us restore swiotlb functionality for PV by fulfilling this new
requirement.
This change addresses what turned out to be a fragility in
commit 64e1f0c531d1 ("s390/mm: force swiotlb for protected
virtualization"), which ain't exactly broken in its original context,
but could give us some more headache if people backport the broken
change and forget this fix.
Signed-off-by: Halil Pasic <pasic@linux.ibm.com>
Tested-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Fixes: 903cd0f315fe ("swiotlb: Use is_swiotlb_force_bounce for swiotlb data bouncing")
Fixes: 64e1f0c531d1 ("s390/mm: force swiotlb for protected virtualization")
Cc: stable@vger.kernel.org #5.3+
Signed-off-by: Konrad Rzeszutek Wilk <konrad@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 030f653078316a9cc9ca6bd1b0234dcf858be35d upstream.
I was debugging some crashes on parisc and I found out that there is a
crash possibility if a function using alloca is interrupted by a signal.
The reason for the crash is that the gcc alloca implementation leaves
garbage in the upper 32 bits of the sp register. This normally doesn't
matter (the upper bits are ignored because the PSW W-bit is clear),
however the signal delivery routine in the kernel uses full 64 bits of sp
and it fails with -EFAULT if the upper 32 bits are not zero.
I created this program that demonstrates the problem:
#include <stdlib.h>
#include <unistd.h>
#include <signal.h>
#include <alloca.h>
static __attribute__((noinline,noclone)) void aa(int *size)
{
void * volatile p = alloca(-*size);
while (1) ;
}
static void handler(int sig)
{
write(1, "signal delivered\n", 17);
_exit(0);
}
int main(void)
{
int size = -0x100;
signal(SIGALRM, handler);
alarm(1);
aa(&size);
}
If you compile it with optimizations, it will crash.
The "aa" function has this disassembly:
000106a0 <aa>:
106a0: 08 03 02 41 copy r3,r1
106a4: 08 1e 02 43 copy sp,r3
106a8: 6f c1 00 80 stw,ma r1,40(sp)
106ac: 37 dc 3f c1 ldo -20(sp),ret0
106b0: 0c 7c 12 90 stw ret0,8(r3)
106b4: 0f 40 10 9c ldw 0(r26),ret0 ; ret0 = 0x00000000FFFFFF00
106b8: 97 9c 00 7e subi 3f,ret0,ret0 ; ret0 = 0xFFFFFFFF0000013F
106bc: d7 80 1c 1a depwi 0,31,6,ret0 ; ret0 = 0xFFFFFFFF00000100
106c0: 0b 9e 0a 1e add,l sp,ret0,sp ; sp = 0xFFFFFFFFxxxxxxxx
106c4: e8 1f 1f f7 b,l,n 106c4 <aa+0x24>,r0
This patch fixes the bug by truncating the "usp" variable to 32 bits.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit db87db65c1059f3be04506d122f8ec9b2fa3b05e ]
> Hi Arnd,
>
> First bad commit (maybe != root cause):
>
> tree: https://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git master
> head: 2f73937c9aa561e2082839bc1a8efaac75d6e244
> commit: 47fd22f2b84765a2f7e3f150282497b902624547 [4771/5318] cs89x0: rework driver configuration
> config: m68k-randconfig-c003-20210804 (attached as .config)
> compiler: m68k-linux-gcc (GCC) 10.3.0
> reproduce (this is a W=1 build):
> wget https://raw.githubusercontent.com/intel/lkp-tests/master/sbin/make.cross -O ~/bin/make.cross
> chmod +x ~/bin/make.cross
> # https://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git/commit/?id=47fd22f2b84765a2f7e3f150282497b902624547
> git remote add linux-next https://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git
> git fetch --no-tags linux-next master
> git checkout 47fd22f2b84765a2f7e3f150282497b902624547
> # save the attached .config to linux build tree
> COMPILER_INSTALL_PATH=$HOME/0day COMPILER=gcc-10.3.0 make.cross ARCH=m68k
>
> If you fix the issue, kindly add following tag as appropriate
> Reported-by: kernel test robot <lkp@intel.com>
>
> All errors (new ones prefixed by >>):
>
> In file included from include/linux/kernel.h:19,
> from include/linux/list.h:9,
> from include/linux/module.h:12,
> from drivers/net/ethernet/cirrus/cs89x0.c:51:
> drivers/net/ethernet/cirrus/cs89x0.c: In function 'net_open':
> drivers/net/ethernet/cirrus/cs89x0.c:897:20: error: implicit declaration of function 'isa_virt_to_bus'; did you mean 'virt_to_bus'? [-Werror=implicit-function-declaration]
> 897 | (unsigned long)isa_virt_to_bus(lp->dma_buff));
> | ^~~~~~~~~~~~~~~
> include/linux/printk.h:141:17: note: in definition of macro 'no_printk'
> 141 | printk(fmt, ##__VA_ARGS__); \
> | ^~~~~~~~~~~
> drivers/net/ethernet/cirrus/cs89x0.c:86:3: note: in expansion of macro 'pr_debug'
> 86 | pr_##level(fmt, ##__VA_ARGS__); \
> | ^~~
> drivers/net/ethernet/cirrus/cs89x0.c:894:3: note: in expansion of macro 'cs89_dbg'
> 894 | cs89_dbg(1, debug, "%s: dma %lx %lx\n",
> | ^~~~~~~~
> >> drivers/net/ethernet/cirrus/cs89x0.c:914:3: error: implicit declaration of function 'disable_dma'; did you mean 'disable_irq'? [-Werror=implicit-function-declaration]
As far as I can tell, this is a bug with the m68kmmu architecture, not
with my driver:
The CONFIG_ISA_DMA_API option is provided for coldfire, which implements it,
but dragonball also sets the option as a side-effect, without actually
implementing
the interfaces. The patch below should fix it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c1a6018d1839c9cb8f807dc863a50102a1a5c412 ]
ls1046afrwy and ls1046ardb boards have CAT24C04[1] and CAT24C05[2]
eeproms respectively. Both are 4Kb (512 bytes) in size,
and compatible with AT24C04[3].
Remove multi-address entries, as both the boards have a single chip each.
[1] https://www.onsemi.com/pdf/datasheet/cat24c01-d.pdf
[2] https://www.onsemi.com/pdf/datasheet/cat24c03-d.pdf
[3] https://ww1.microchip.com/downloads/en/DeviceDoc/doc0180.pdf
Signed-off-by: Raag Jadav <raagjadav@gmail.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f865d0292ff3c0ca09414436510eb4c815815509 ]
The documented compatible string for the CPUs found on Tegra132 is
"nvidia,tegra132-denver", rather than the previously used compatible
string "nvidia,denver".
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2270ad2f4e123336af685ecedd1618701cb4ca1e ]
This patch fixes the tristate and pullup configuration for UART 1 to 3
on the Tamonten SOM.
Signed-off-by: Andreas Obergschwandtner <andreas.obergschwandtner@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c81210e38966cfa1c784364e4035081c3227cf5b ]
memory node like other node should be node@reg, which is missing in this
case, so fix it up
arch/arm64/boot/dts/qcom/ipq8074-hk01.dt.yaml: /: memory: False schema does not allow {'device_type': ['memory'], 'reg': [[0, 1073741824, 0, 536870912]]}
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20210308060826.3074234-18-vkoul@kernel.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit cd7cd5b716d594e27a933c12f026d4f2426d7bf4 ]
PPD has only one ACHC device, which effectively is a Kinetis
microcontroller. It has one SPI interface used for normal
communication. Additionally it's possible to flash the device
firmware using NXP's EzPort protocol by correctly driving a
second chip select pin and the device reset pin.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20210802172309.164365-3-sebastian.reichel@collabora.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit bf2942a8b7c38e8cc2d5157b4f0323d7f4e5ec71 ]
The initialization sequence performed by the generic platform driver
pcie-designware-plat.c for a DWC based implementation doesn't work for
Tegra194. Tegra194 has a different initialization sequence requirement
which can only be satisfied by the Tegra194 specific platform driver
pcie-tegra194.c. So, remove the generic compatible string "snps,dw-pcie-ep"
from Tegra194's endpoint controller nodes.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 23411c720052ad860b3e579ee4873511e367130a ]
While alloc_tty_driver failure in rs_init would mean we have much bigger
problem, there is no reason to panic when tty_register_driver fails
there. It can fail for various reasons.
So handle the failure gracefully. Actually handle them both while at it.
This will make at least the console functional as it was enabled earlier
by console_initcall in iss_console_init. Instead of shooting down the
whole system.
We move tty_port_init() after alloc_tty_driver(), so that we don't need
to destroy the port in case the latter function fails.
Cc: Chris Zankel <chris@zankel.net>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: linux-xtensa@linux-xtensa.org
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210723074317.32690-2-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 3322ba0d7bea1e24ae464418626f6a15b69533ab ]
Kernel support for the newer PCI mio instructions can be toggled off
with the pci=nomio command line option which needs to integrate with
common code PCI option parsing. However this option then toggles static
branches which can't be toggled yet in an early_param() call.
Thus commit 9964f396f1d0 ("s390: fix setting of mio addressing control")
moved toggling the static branches to the PCI init routine.
With this setup however we can't check for mio support outside the PCI
code during early boot, i.e. before switching the static branches, which
we need to be able to export this as an ELF HWCAP.
Improve on this by turning mio availability into a machine flag that
gets initially set based on CONFIG_PCI and the facility bit and gets
toggled off if pci=nomio is found during PCI option parsing allowing
simple access to this machine flag after early init.
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5492886c14744d239e87f1b0b774b5a341e755cc ]
In case of a jump label print the real address of the piece of code
where a mismatch was detected. This is right before the system panics,
so there is nothing revealed.
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0dc6c59892ead17a9febd11202c9f6794aac1895 ]
Since new code doesn't take old clk names in account, it does fixes
error:
msm_dsi 4700000.mdss_dsi: dev_pm_opp_set_clkname: Couldn't find clock: -2
and following kernel oops introduced by
b0530eb1191 ("drm/msm/dpu: Use OPP API to set clk/perf state").
Also removes warning about deprecated clock names.
Tested against linux-5.10.y LTS on Nexus 7 2013.
Reviewed-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: David Heidelberg <david@ixit.cz>
Link: https://lore.kernel.org/r/20210707131453.24041-1-david@ixit.cz
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit bea6a94a279bcbe6b2cde348782b28baf12255a5 ]
Starting with following patch MIPS Malta is not able to boot:
| commit 79edff12060fe7772af08607eff50c0e2486c5ba
| Author: Rob Herring <robh@kernel.org>
| scripts/dtc: Update to upstream version v1.6.0-51-g183df9e9c2b9
The reason is the alignment test added to the fdt_ro_probe_(). To fix
this issue, we need to make sure that fdt_buf is aligned.
Since the dtc patch was designed to uncover potential issue, I handle
initial MIPS Malta patch as initial bug.
Fixes: e81a8c7dabac ("MIPS: Malta: Setup RAM regions via DT")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 1d78dfde33a02da1d816279c2e3452978b7abd39 ]
Since commit e1a1ef84cd07 ("KVM: PPC: Book3S: Allocate guest TCEs on
demand too"), pages for TCE tables for KVM guests are allocated only
when needed. This allows skipping any update when clearing TCEs. This
works mostly fine as TCE updates are handled when the MMU is enabled.
The realmode handlers fail with H_TOO_HARD when pages are not yet
allocated, except when clearing a TCE in which case KVM prints a warning
and proceeds to dereference a NULL pointer, which crashes the host OS.
This has not been caught so far as the change in commit e1a1ef84cd07 is
reasonably new, and POWER9 runs mostly radix which does not use realmode
handlers. With hash, the default TCE table is memset() by QEMU when the
machine is reset which triggers page faults and the KVM TCE device's
kvm_spapr_tce_fault() handles those with MMU on. And the huge DMA
windows are not cleared by VMs which instead successfully create a DMA
window big enough to map the VM memory 1:1 and then VMs just map
everything without clearing.
This started crashing now as commit 381ceda88c4c ("powerpc/pseries/iommu:
Make use of DDW for indirect mapping") added a mode when a dymanic DMA
window not big enough to map the VM memory 1:1 but it is used anyway,
and the VM now is the first (i.e. not QEMU) to clear a just created
table. Note that upstream QEMU needs to be modified to trigger the VM to
trigger the host OS crash.
This replaces WARN_ON_ONCE_RM() with a check and return, and adds
another warning if TCE is not being cleared.
Fixes: e1a1ef84cd07 ("KVM: PPC: Book3S: Allocate guest TCEs on demand too")
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210827040706.517652-1-aik@ozlabs.ru
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
are live
[ Upstream commit 1782663897945a5cf28e564ba5eed730098e9aa4 ]
After the L1 saves its PMU SPRs but before loading the L2's PMU SPRs,
switch the pmcregs_in_use field in the L1 lppaca to the value advertised
by the L2 in its VPA. On the way out of the L2, set it back after saving
the L2 PMU registers (if they were in-use).
This transfers the PMU liveness indication between the L1 and L2 at the
points where the registers are not live.
This fixes the nested HV bug for which a workaround was added to the L0
HV by commit 63279eeb7f93a ("KVM: PPC: Book3S HV: Always save guest pmu
for guest capable of nesting"), which explains the problem in detail.
That workaround is no longer required for guests that include this bug
fix.
Fixes: 360cae313702 ("KVM: PPC: Book3S HV: Nested guest entry via hypercall")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Fabiano Rosas <farosas@linux.ibm.com>
Link: https://lore.kernel.org/r/20210811160134.904987-10-npiggin@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit d0e28a6145c3455b69991245e7f6147eb914b34a ]
CONFIG_MTD_PHYSMAP_OF is not longer enabled as it depends on
MTD_PHYSMAP which is not enabled.
This is a regression from commit 642b1e8dbed7 ("mtd: maps: Merge
physmap_of.c into physmap-core.c"), which added the extra dependency.
Add CONFIG_MTD_PHYSMAP=y so this stays in the config, as Christophe said
it is useful for build coverage.
Fixes: 642b1e8dbed7 ("mtd: maps: Merge physmap_of.c into physmap-core.c")
Signed-off-by: Joel Stanley <joel@jms.id.au>
Acked-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210817045407.2445664-3-joel@jms.id.au
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 946e1052cdcc7e585ee5d1e72528ca49fb295243 ]
Don't call printk() when CONFIG_PRINTK is not set.
Fixes the following build errors:
or1k-linux-ld: arch/openrisc/kernel/entry.o: in function `_external_irq_handler':
(.text+0x804): undefined reference to `printk'
(.text+0x804): relocation truncated to fit: R_OR1K_INSN_REL_26 against undefined symbol `printk'
Fixes: 9d02a4283e9c ("OpenRISC: Boot code")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
Cc: Stafford Horne <shorne@gmail.com>
Cc: openrisc@lists.librecores.org
Signed-off-by: Stafford Horne <shorne@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit a6cae77f1bc89368a4e2822afcddc45c3062d499 ]
commit 7c6986ade69e ("powerpc/stacktrace: Fix spurious "stale" traces in raise_backtrace_ipi()")
introduces udelay() call without including the linux/delay.h header.
This may happen to work on master but the header that declares the
functionshould be included nonetheless.
Fixes: 7c6986ade69e ("powerpc/stacktrace: Fix spurious "stale" traces in raise_backtrace_ipi()")
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210729180103.15578-1-msuchanek@suse.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit b30d0289de72c62516df03fdad8d53f552c69839 upstream.
The merge_fdt_bootargs() function by definition consumes more than 1024
bytes of stack because it has a 1024 byte command line on the stack,
meaning that we always get a warning when building this file:
arch/arm/boot/compressed/atags_to_fdt.c: In function 'merge_fdt_bootargs':
arch/arm/boot/compressed/atags_to_fdt.c:98:1: warning: the frame size of 1032 bytes is larger than 1024 bytes [-Wframe-larger-than=]
However, as this is the decompressor and we know that it has a very shallow
call chain, and we do not actually risk overflowing the kernel stack
at runtime here.
This just shuts up the warning by disabling the warning flag for this
file.
Tested on Nexus 7 2012 builds.
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: David Heidelberg <david@ixit.cz>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 90268574a3e8a6b883bd802d702a2738577e1006 upstream.
The `compute_indices` and `populate_entries` macros operate on inclusive
bounds, and thus the `map_memory` macro which uses them also operates
on inclusive bounds.
We pass `_end` and `_idmap_text_end` to `map_memory`, but these are
exclusive bounds, and if one of these is sufficiently aligned (as a
result of kernel configuration, physical placement, and KASLR), then:
* In `compute_indices`, the computed `iend` will be in the page/block *after*
the final byte of the intended mapping.
* In `populate_entries`, an unnecessary entry will be created at the end
of each level of table. At the leaf level, this entry will map up to
SWAPPER_BLOCK_SIZE bytes of physical addresses that we did not intend
to map.
As we may map up to SWAPPER_BLOCK_SIZE bytes more than intended, we may
violate the boot protocol and map physical address past the 2MiB-aligned
end address we are permitted to map. As we map these with Normal memory
attributes, this may result in further problems depending on what these
physical addresses correspond to.
The final entry at each level may require an additional table at that
level. As EARLY_ENTRIES() calculates an inclusive bound, we allocate
enough memory for this.
Avoid the extraneous mapping by having map_memory convert the exclusive
end address to an inclusive end address by subtracting one, and do
likewise in EARLY_ENTRIES() when calculating the number of required
tables. For clarity, comments are updated to more clearly document which
boundaries the macros operate on. For consistency with the other
macros, the comments in map_memory are also updated to describe `vstart`
and `vend` as virtual addresses.
Fixes: 0370b31e4845 ("arm64: Extend early page table code to allow for larger kernels")
Cc: <stable@vger.kernel.org> # 4.16.x
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Anshuman Khandual <anshuman.khandual@arm.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Steve Capper <steve.capper@arm.com>
Cc: Will Deacon <will@kernel.org>
Acked-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20210823101253.55567-1-mark.rutland@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4b511d5bfa74b1926daefd1694205c7f1bcf677f upstream.
Xen PV guests are specifying the highest used PFN via the max_pfn
field in shared_info. This value is used by the Xen tools when saving
or migrating the guest.
Unfortunately this field is misnamed, as in reality it is specifying
the number of pages (including any memory holes) of the guest, so it
is the highest used PFN + 1. Renaming isn't possible, as this is a
public Xen hypervisor interface which needs to be kept stable.
The kernel will set the value correctly initially at boot time, but
when adding more pages (e.g. due to memory hotplug or ballooning) a
real PFN number is stored in max_pfn. This is done when expanding the
p2m array, and the PFN stored there is even possibly wrong, as it
should be the last possible PFN of the just added P2M frame, and not
one which led to the P2M expansion.
Fix that by setting shared_info->max_pfn to the last possible PFN + 1.
Fixes: 98dd166ea3a3c3 ("x86/xen/p2m: hint at the last populated P2M entry")
Cc: stable@vger.kernel.org
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Link: https://lore.kernel.org/r/20210730092622.9973-2-jgross@suse.com
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f9addd85fbfacf0d155e83dbee8696d6df5ed0c7 upstream.
H_GetPerformanceCounterInfo (0xF080) hcall returns the counter data in
the result buffer. Result buffer has specific format defined in the PAPR
specification. One of the fields is counter offset and width of the
counter data returned.
Counter data are returned in a unsigned char array in big endian byte
order. To get the final counter data, the values must be left shifted
byte at a time. But commit 220a0c609ad17 ("powerpc/perf: Add support for
the hv gpci (get performance counter info) interface") made the shifting
bitwise and also assumed little endian order. Because of that, hcall
counters values are reported incorrectly.
In particular this can lead to counters go backwards which messes up the
counter prev vs now calculation and leads to huge counter value
reporting:
#: perf stat -e hv_gpci/system_tlbie_count_and_time_tlbie_instructions_issued/
-C 0 -I 1000
time counts unit events
1.000078854 18,446,744,073,709,535,232 hv_gpci/system_tlbie_count_and_time_tlbie_instructions_issued/
2.000213293 0 hv_gpci/system_tlbie_count_and_time_tlbie_instructions_issued/
3.000320107 0 hv_gpci/system_tlbie_count_and_time_tlbie_instructions_issued/
4.000428392 0 hv_gpci/system_tlbie_count_and_time_tlbie_instructions_issued/
5.000537864 0 hv_gpci/system_tlbie_count_and_time_tlbie_instructions_issued/
6.000649087 0 hv_gpci/system_tlbie_count_and_time_tlbie_instructions_issued/
7.000760312 0 hv_gpci/system_tlbie_count_and_time_tlbie_instructions_issued/
8.000865218 16,448 hv_gpci/system_tlbie_count_and_time_tlbie_instructions_issued/
9.000978985 18,446,744,073,709,535,232 hv_gpci/system_tlbie_count_and_time_tlbie_instructions_issued/
10.001088891 16,384 hv_gpci/system_tlbie_count_and_time_tlbie_instructions_issued/
11.001201435 0 hv_gpci/system_tlbie_count_and_time_tlbie_instructions_issued/
12.001307937 18,446,744,073,709,535,232 hv_gpci/system_tlbie_count_and_time_tlbie_instructions_issued/
Fix the shifting logic to correct match the format, ie. read bytes in
big endian order.
Fixes: e4f226b1580b ("powerpc/perf/hv-gpci: Increase request buffer size")
Cc: stable@vger.kernel.org # v4.6+
Reported-by: Nageswara R Sastry<rnsastry@linux.ibm.com>
Signed-off-by: Kajol Jain <kjain@linux.ibm.com>
Tested-by: Nageswara R Sastry<rnsastry@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210813082158.429023-1-kjain@linux.ibm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f7782bb8d818d8f47c26b22079db10599922787a upstream.
Clear nested.pi_pending on nested VM-Enter even if L2 will run without
posted interrupts enabled. If nested.pi_pending is left set from a
previous L2, vmx_complete_nested_posted_interrupt() will pick up the
stale flag and exit to userspace with an "internal emulation error" due
the new L2 not having a valid nested.pi_desc.
Arguably, vmx_complete_nested_posted_interrupt() should first check for
posted interrupts being enabled, but it's also completely reasonable that
KVM wouldn't screw up a fundamental flag. Not to mention that the mere
existence of nested.pi_pending is a long-standing bug as KVM shouldn't
move the posted interrupt out of the IRR until it's actually processed,
e.g. KVM effectively drops an interrupt when it performs a nested VM-Exit
with a "pending" posted interrupt. Fixing the mess is a future problem.
Prior to vmx_complete_nested_posted_interrupt() interpreting a null PI
descriptor as an error, this was a benign bug as the null PI descriptor
effectively served as a check on PI not being enabled. Even then, the
new flow did not become problematic until KVM started checking the result
of kvm_check_nested_events().
Fixes: 705699a13994 ("KVM: nVMX: Enable nested posted interrupt processing")
Fixes: 966eefb89657 ("KVM: nVMX: Disable vmcs02 posted interrupts if vmcs12 PID isn't mappable")
Fixes: 47d3530f86c0 ("KVM: x86: Exit to userspace when kvm_check_nested_events fails")
Cc: stable@vger.kernel.org
Cc: Jim Mattson <jmattson@google.com>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210810144526.2662272-1-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
adjusted
commit d9130a2dfdd4b21736c91b818f87dbc0ccd1e757 upstream.
When MSR_IA32_TSC_ADJUST is written by guest due to TSC ADJUST feature
especially there's a big tsc warp (like a new vCPU is hot-added into VM
which has been up for a long time), tsc_offset is added by a large value
then go back to guest. This causes system time jump as tsc_timestamp is
not adjusted in the meantime and pvclock monotonic character.
To fix this, just notify kvm to update vCPU's guest time before back to
guest.
Cc: stable@vger.kernel.org
Signed-off-by: Zelin Deng <zelin.deng@linux.alibaba.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <1619576521-81399-2-git-send-email-zelin.deng@linux.alibaba.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a3e03bc1368c1bc16e19b001fc96dc7430573cc8 upstream.
While in practice vcpu->vcpu_idx == vcpu->vcp_id is often true, it may
not always be, and we must not rely on this. Reason is that KVM decides
the vcpu_idx, userspace decides the vcpu_id, thus the two might not
match.
Currently kvm->arch.idle_mask is indexed by vcpu_id, which implies
that code like
for_each_set_bit(vcpu_id, kvm->arch.idle_mask, online_vcpus) {
vcpu = kvm_get_vcpu(kvm, vcpu_id);
do_stuff(vcpu);
}
is not legit. Reason is that kvm_get_vcpu expects an vcpu_idx, not an
vcpu_id. The trouble is, we do actually use kvm->arch.idle_mask like
this. To fix this problem we have two options. Either use
kvm_get_vcpu_by_id(vcpu_id), which would loop to find the right vcpu_id,
or switch to indexing via vcpu_idx. The latter is preferable for obvious
reasons.
Let us make switch from indexing kvm->arch.idle_mask by vcpu_id to
indexing it by vcpu_idx. To keep gisa_int.kicked_mask indexed by the
same index as idle_mask lets make the same change for it as well.
Fixes: 1ee0bc559dc3 ("KVM: s390: get rid of local_int array")
Signed-off-by: Halil Pasic <pasic@linux.ibm.com>
Reviewed-by: Christian Bornträger <borntraeger@de.ibm.com>
Reviewed-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Cc: <stable@vger.kernel.org> # 3.15+
Link: https://lore.kernel.org/r/20210827125429.1912577-1-pasic@linux.ibm.com
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 527f721478bce3f49b513a733bacd19d6f34b08c upstream.
The recent commit
064855a69003 ("x86/resctrl: Fix default monitoring groups reporting")
caused a RHEL build failure with an uninitialized variable warning
treated as an error because it removed the default case snippet.
The RHEL Makefile uses '-Werror=maybe-uninitialized' to force possibly
uninitialized variable warnings to be treated as errors. This is also
reported by smatch via the 0day robot.
The error from the RHEL build is:
arch/x86/kernel/cpu/resctrl/monitor.c: In function ‘__mon_event_count’:
arch/x86/kernel/cpu/resctrl/monitor.c:261:12: error: ‘m’ may be used
uninitialized in this function [-Werror=maybe-uninitialized]
m->chunks += chunks;
^~
The upstream Makefile does not build using '-Werror=maybe-uninitialized'.
So, the problem is not seen there. Fix the problem by putting back the
default case snippet.
[ bp: note that there's nothing wrong with the code and other compilers
do not trigger this warning - this is being done just so the RHEL compiler
is happy. ]
Fixes: 064855a69003 ("x86/resctrl: Fix default monitoring groups reporting")
Reported-by: Terry Bowman <Terry.Bowman@amd.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Babu Moger <babu.moger@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/162949631908.23903.17090272726012848523.stgit@bmoger-ubuntu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f11dd0d80555cdc8eaf5cfc9e19c9e198217f9f1 upstream.
Commit:
2ff40250691e ("perf/core, arch/x86: Use PERF_PMU_CAP_NO_EXCLUDE for exclusion incapable PMUs")
neglected to do so.
Fixes: 2ff40250691e ("perf/core, arch/x86: Use PERF_PMU_CAP_NO_EXCLUDE for exclusion incapable PMUs")
Signed-off-by: Kim Phillips <kim.phillips@amd.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210817221048.88063-2-kim.phillips@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f5e81d1117501546b7be050c5fbafa6efd2c722c upstream.
In case of JITs, each of the JIT backends compiles the BPF nospec instruction
/either/ to a machine instruction which emits a speculation barrier /or/ to
/no/ machine instruction in case the underlying architecture is not affected
by Speculative Store Bypass or has different mitigations in place already.
This covers both x86 and (implicitly) arm64: In case of x86, we use 'lfence'
instruction for mitigation. In case of arm64, we rely on the firmware mitigation
as controlled via the ssbd kernel parameter. Whenever the mitigation is enabled,
it works for all of the kernel code with no need to provide any additional
instructions here (hence only comment in arm64 JIT). Other archs can follow
as needed. The BPF nospec instruction is specifically targeting Spectre v4
since i) we don't use a serialization barrier for the Spectre v1 case, and
ii) mitigation instructions for v1 and v4 might be different on some archs.
The BPF nospec is required for a future commit, where the BPF verifier does
annotate intermediate BPF programs with speculation barriers.
Co-developed-by: Piotr Krysiuk <piotras@gmail.com>
Co-developed-by: Benedict Schlueter <benedict.schlueter@rub.de>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Piotr Krysiuk <piotras@gmail.com>
Signed-off-by: Benedict Schlueter <benedict.schlueter@rub.de>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[OP: - adjusted context for 5.4
- apply riscv changes to /arch/riscv/net/bpf_jit_comp.c]
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 01c72cad790cb6cd3ccbe4c1402b6cb6c6bbffd0 ]
The GIC-400 CPU interfaces address range is defined as 0x2000-0x3FFF (by
ARM).
Reported-by: Sam Protsenko <semen.protsenko@linaro.org>
Reported-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Fixes: b9024cbc937d ("arm64: dts: Add initial device tree support for exynos7")
Link: https://lore.kernel.org/r/20210805072110.4730-1-krzysztof.kozlowski@canonical.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 72ccc373b064ae3ac0c5b5f2306069b60ca118df ]
After enabling CONFIG_REGULATOR_DEBUG=y we observer below debug logs.
Changes help link VCCK and VDDEE pwm regulator to 5V regulator supply
instead of dummy regulator.
[ 7.117140] pwm-regulator regulator-vcck: Looking up pwm-supply from device tree
[ 7.117153] pwm-regulator regulator-vcck: Looking up pwm-supply property in node /regulator-vcck failed
[ 7.117184] VCCK: supplied by regulator-dummy
[ 7.117194] regulator-dummy: could not add device link regulator.8: -ENOENT
[ 7.117266] VCCK: 860 <--> 1140 mV at 986 mV, enabled
[ 7.118498] VDDEE: will resolve supply early: pwm
[ 7.118515] pwm-regulator regulator-vddee: Looking up pwm-supply from device tree
[ 7.118526] pwm-regulator regulator-vddee: Looking up pwm-supply property in node /regulator-vddee failed
[ 7.118553] VDDEE: supplied by regulator-dummy
[ 7.118563] regulator-dummy: could not add device link regulator.9: -ENOENT
Fixes: 087a1d8b4e4c ("ARM: dts: meson8b: ec100: add the VDDEE regulator")
Fixes: 3e7db1c1b7a3 ("ARM: dts: meson8b: ec100: improve the description of the regulators")
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20210705112358.3554-4-linux.amoon@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 632062e540becbbcb067523ec8bcadb1239d9578 ]
After enabling CONFIG_REGULATOR_DEBUG=y we observer below debug logs.
Changes help link VCCK and VDDEE pwm regulator to 5V regulator supply
instead of dummy regulator.
Add missing pwm-supply for regulator-vcck regulator node.
[ 7.117140] pwm-regulator regulator-vcck: Looking up pwm-supply from device tree
[ 7.117153] pwm-regulator regulator-vcck: Looking up pwm-supply property in node /regulator-vcck failed
[ 7.117184] VCCK: supplied by regulator-dummy
[ 7.117194] regulator-dummy: could not add device link regulator.8: -ENOENT
[ 7.117266] VCCK: 860 <--> 1140 mV at 986 mV, enabled
[ 7.118498] VDDEE: will resolve supply early: pwm
[ 7.118515] pwm-regulator regulator-vddee: Looking up pwm-supply from device tree
[ 7.118526] pwm-regulator regulator-vddee: Looking up pwm-supply property in node /regulator-vddee failed
[ 7.118553] VDDEE: supplied by regulator-dummy
[ 7.118563] regulator-dummy: could not add device link regulator.9: -ENOENT
Fixes: dee51cd0d2e8 ("ARM: dts: meson8b: mxq: add the VDDEE regulator")
Fixes: d94f60e3dfa0 ("ARM: dts: meson8b: mxq: improve support for the TRONFY MXQ S805")
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20210705112358.3554-3-linux.amoon@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 876228e9f935f19c7afc7ba394d17e2ec9143b65 ]
After enabling CONFIG_REGULATOR_DEBUG=y we observe below debug logs.
Changes help link VCCK and VDDEE pwm regulator to 5V regulator supply
instead of dummy regulator.
[ 7.117140] pwm-regulator regulator-vcck: Looking up pwm-supply from device tree
[ 7.117153] pwm-regulator regulator-vcck: Looking up pwm-supply property in node /regulator-vcck failed
[ 7.117184] VCCK: supplied by regulator-dummy
[ 7.117194] regulator-dummy: could not add device link regulator.8: -ENOENT
[ 7.117266] VCCK: 860 <--> 1140 mV at 986 mV, enabled
[ 7.118498] VDDEE: will resolve supply early: pwm
[ 7.118515] pwm-regulator regulator-vddee: Looking up pwm-supply from device tree
[ 7.118526] pwm-regulator regulator-vddee: Looking up pwm-supply property in node /regulator-vddee failed
[ 7.118553] VDDEE: supplied by regulator-dummy
[ 7.118563] regulator-dummy: could not add device link regulator.9: -ENOENT
Fixes: 524d96083b66 ("ARM: dts: meson8b: odroidc1: add the CPU voltage regulator")
Fixes: 8bdf38be712d ("ARM: dts: meson8b: odroidc1: add the VDDEE regulator")
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
[narmstrong: fixed typo in commit s/observer/observe/]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20210705112358.3554-2-linux.amoon@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 44cf630bcb8c5ec78125805c9447dd5766792224 ]
We are seeing "imprecise external abort (0x1406)" errors during boot
(which then cause the whole board to hang) on Meson8 (but not Meson8m2).
These are observed while trying to access the GPU's registers when the
MALI clock is running at it's default setting of 24MHz. The 3.10 vendor
kernel uses 318.75MHz as "default" GPU frequency. Using that makes the
"imprecise external aborts" go away.
Add the assigned-clocks and assigned-clock-rates properties to also bump
the MALI clock to 318.75MHz before accessing any of it's registers.
Fixes: 7d3f6b536e72c9 ("ARM: dts: meson8: add the Mali-450 MP6 GPU")
Reported-by: Demetris Ierokipides <ierokipides.dem@gmail.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20210711214023.2163565-1-martin.blumenstingl@googlemail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4ec82a7bb3db8c6005e715c63224c32d458917a2 ]
The "max-clock" and "min-vrefresh" properties fail to validate with
commit cfe34bb7a770c5d8 ("dt-bindings: drm: bridge: adi,adv7511.txt:
convert to yaml"). Drop them, as they are parts of an out-of-tree
workaround that is not needed upstream.
Fixes: bcf3003438ea4645 ("arm64: dts: renesas: r8a77995: draak: Enable HDMI display output")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Link: https://lore.kernel.org/r/975b6686bc423421b147d367fe7fb9a0db99c5af.1625134398.git.geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8c295b7f3d01359ff4336fcb6e406e6ed37957d6 ]
The HVI3C shall be a group of I3C function, not an independent function.
Correct the function name from "HVI3C" to "I3C".
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Fixes: f510f04c8c83 ("ARM: dts: aspeed: Add AST2600 pinmux nodes")
Link: https://lore.kernel.org/r/20201029062723.20798-1-dylan_hung@aspeedtech.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 761608f5cf70e8876c2f0e39ca54b516bdcb7c12 ]
In the for loop all nfeth_dev array members should be freed, not only
the first one. Freeing only the first array member can cause
double-free bugs and memory leaks.
Fixes: 9cd7b148312f ("m68k/atari: ARAnyM - Add support for network access")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Link: https://lore.kernel.org/r/20210705204727.10743-1-paskripkin@gmail.com
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9372a82892c2caa6bccab9a4081166fa769699f8 ]
Currently allocation and registration of s390dbf debug areas are tied
together. As a result, a debug area cannot be unregistered and
re-registered while any process has an associated debugfs file open.
Fix this by splitting alloc/release from register/unregister.
Signed-off-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ddd63c85ef67ea9ea7282ad35eafb6568047126e ]
It is currently possible to initialize a large PMD page when
the address is not aligned on page boundary.
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Reviewed-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit a729691b541f6e63043beae72e635635abe5dc09 upstream.
When this platform was relatively new in November 2011, with early BIOS
revisions, a reboot quirk was added in commit 6be30bb7d750 ("x86/reboot:
Blacklist Dell OptiPlex 990 known to require PCI reboot")
However, this quirk (and several others) are open-ended to all BIOS
versions and left no automatic expiry if/when the system BIOS fixed the
issue, meaning that nobody is likely to come along and re-test.
What is really problematic with using PCI reboot as this quirk does, is
that it causes this platform to do a full power down, wait one second,
and then power back on. This is less than ideal if one is using it for
boot testing and/or bisecting kernels when legacy rotating hard disks
are installed.
It was only by chance that the quirk was noticed in dmesg - and when
disabled it turned out that it wasn't required anymore (BIOS A24), and a
default reboot would work fine without the "harshness" of power cycling the
machine (and disks) down and up like the PCI reboot does.
Doing a bit more research, it seems that the "newest" BIOS for which the
issue was reported[1] was version A06, however Dell[2] seemed to suggest
only up to and including version A05, with the A06 having a large number of
fixes[3] listed.
As is typical with a new platform, the initial BIOS updates come frequently
and then taper off (and in this case, with a revival for CPU CVEs); a
search for O990-A<ver>.exe reveals the following dates:
A02 16 Mar 2011
A03 11 May 2011
A06 14 Sep 2011
A07 24 Oct 2011
A10 08 Dec 2011
A14 06 Sep 2012
A16 15 Oct 2012
A18 30 Sep 2013
A19 23 Sep 2015
A20 02 Jun 2017
A23 07 Mar 2018
A24 21 Aug 2018
While it's overkill to flash and test each of the above, it would seem
likely that the issue was contained within A0x BIOS versions, given the
dates above and the dates of issue reports[4] from distros. So rather than
just throw out the quirk entirely, limit the scope to just those early BIOS
versions, in case people are still running systems from 2011 with the
original as-shipped early A0x BIOS versions.
[1] https://lore.kernel.org/lkml/1320373471-3942-1-git-send-email-trenn@suse.de/
[2] https://www.dell.com/support/kbdoc/en-ca/000131908/linux-based-operating-systems-stall-upon-reboot-on-optiplex-390-790-990-systems
[3] https://www.dell.com/support/home/en-ca/drivers/driversdetails?driverid=85j10
[4] https://bugs.launchpad.net/ubuntu/+source/linux/+bug/768039
Fixes: 6be30bb7d750 ("x86/reboot: Blacklist Dell OptiPlex 990 known to require PCI reboot")
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210530162447.996461-4-paul.gortmaker@windriver.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e10de314287c2c14b0e6f0e3e961975ce2f4a83d upstream.
On certain AMD platforms, when the IOMMU performance counter source
(csource) field is zero, power-gating for the counter is enabled, which
prevents write access and returns zero for read access.
This can cause invalid perf result especially when event multiplexing
is needed (i.e. more number of events than available counters) since
the current logic keeps track of the previously read counter value,
and subsequently re-program the counter to continue counting the event.
With power-gating enabled, we cannot gurantee successful re-programming
of the counter.
Workaround this issue by :
1. Modifying the ordering of setting/reading counters and enabing/
disabling csources to only access the counter when the csource
is set to non-zero.
2. Since AMD IOMMU PMU does not support interrupt mode, the logic
can be simplified to always start counting with value zero,
and accumulate the counter value when stopping without the need
to keep track and reprogram the counter with the previously read
counter value.
This has been tested on systems with and without power-gating.
Fixes: 994d6608efe4 ("iommu/amd: Remove performance counter pre-initialization test")
Suggested-by: Alexander Monakov <amonakov@ispras.ru>
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20210504065236.4415-1-suravee.suthikulpanit@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 968339fad422a58312f67718691b717dac45c399 upstream.
.globl sets the symbol binding to STB_GLOBAL while .weak sets the
binding to STB_WEAK. GNU as let .weak override .globl since
binutils-gdb 5ca547dc2399a0a5d9f20626d4bf5547c3ccfddd (1996). Clang
integrated assembler let the last win but it may error in the future.
Since it is a convention that only one binding directive is used, just
delete .globl.
Fixes: ee9d21b3b358 ("powerpc/boot: Ensure _zimage_start is a weak symbol")
Signed-off-by: Fangrui Song <maskray@google.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200325164257.170229-1-maskray@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit bd71c453db91ecb464405411f2821d040f2a0d44 upstream.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
Ilya Leoshkevich
Randy Dunlap
Nicholas Piggin
Mike Rapoport
Mark Brown
Juergen Gross
Halil Pasic
Mikulas Patocka
Arnd Bergmann
Raag Jadav
Thierry Reding
Andreas Obergschwandtner
Vinod Koul
Sebastian Reichel
Vidya Sagar
Jiri Slaby
Niklas Schnelle
Heiko Carstens
David Heidelberg
Oleksij Rempel
Alexey Kardashevskiy
Joel Stanley
Michal Suchanek
Mark Rutland
Kajol Jain
Sean Christopherson
Zelin Deng
Babu Moger
Kim Phillips
Daniel Borkmann
Krzysztof Kozlowski
Anand Moon
Martin Blumenstingl
Geert Uytterhoeven
Dylan Hung
Pavel Skripkin
Peter Oberparleiter
Alexander Gordeev
Paul Gortmaker
Suravee Suthikulpanit
Fangrui Song
Vineet Gupta