| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
- Fix integer overflow in new mobiveil driver (Dan Carpenter)
- Fix race during NVMe removal/rescan (Hari Vyas)
* tag 'pci-v4.18-fixes-5' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: Fix is_added/is_busmaster race condition
PCI: mobiveil: Avoid integer overflow in IB_WIN_SIZE
|
|
When a PCI device is detected, pdev->is_added is set to 1 and proc and
sysfs entries are created.
When the device is removed, pdev->is_added is checked for one and then
device is detached with clearing of proc and sys entries and at end,
pdev->is_added is set to 0.
is_added and is_busmaster are bit fields in pci_dev structure sharing same
memory location.
A strange issue was observed with multiple removal and rescan of a PCIe
NVMe device using sysfs commands where is_added flag was observed as zero
instead of one while removing device and proc,sys entries are not cleared.
This causes issue in later device addition with warning message
"proc_dir_entry" already registered.
Debugging revealed a race condition between the PCI core setting the
is_added bit in pci_bus_add_device() and the NVMe driver reset work-queue
setting the is_busmaster bit in pci_set_master(). As these fields are not
handled atomically, that clears the is_added bit.
Move the is_added bit to a separate private flag variable and use atomic
functions to set and retrieve the device addition state. This avoids the
race because is_added no longer shares a memory location with is_busmaster.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=200283
Signed-off-by: Hari Vyas <hari.vyas@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
On 64-bit servers, SPRN_SPRG3 and its userspace read-only mirror
SPRN_USPRG3 are used as userspace VDSO write and read registers
respectively.
SPRN_SPRG3 is lost when we enter stop4 and above, and is currently not
restored. As a result, any read from SPRN_USPRG3 returns zero on an
exit from stop4 (Power9 only) and above.
Thus in this situation, on POWER9, any call from sched_getcpu() always
returns zero, as on powerpc, we call __kernel_getcpu() which relies
upon SPRN_USPRG3 to report the CPU and NUMA node information.
Fix this by restoring SPRN_SPRG3 on wake up from a deep stop state
with the sprg_vdso value that is cached in PACA.
Fixes: e1c1cfed5432 ("powerpc/powernv: Save/Restore additional SPRs for stop4 cpuidle")
Cc: stable@vger.kernel.org # v4.14+
Reported-by: Florian Weimer <fweimer@redhat.com>
Signed-off-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Reviewed-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild fixes from Masahiro Yamada:
- introduce __diag_* macros and suppress -Wattribute-alias warnings
from GCC 8
- fix stack protector test script for x86_64
- fix line number handling in Kconfig
- document that '#' starts a comment in Kconfig
- handle P_SYMBOL property in dump debugging of Kconfig
- correct help message of LD_DEAD_CODE_DATA_ELIMINATION
- fix occasional segmentation faults in Kconfig
* tag 'kbuild-fixes-v4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kconfig: loop boundary condition fix
kbuild: reword help of LD_DEAD_CODE_DATA_ELIMINATION
kconfig: handle P_SYMBOL in print_symbol()
kconfig: document Kconfig source file comments
kconfig: fix line numbers for if-entries in menu tree
stack-protector: Fix test with 32-bit userland and CONFIG_64BIT=y
powerpc: Remove -Wattribute-alias pragmas
disable -Wattribute-alias warning for SYSCALL_DEFINEx()
kbuild: add macro for controlling warnings to linux/compiler.h
|
|
With SYSCALL_DEFINEx() disabling -Wattribute-alias generically, there's
no need to duplicate that for PowerPC syscalls.
This reverts commit 415520373975 ("powerpc: fix build failure by
disabling attribute-alias warning in pci_32") and commit 2479bfc9bc60
("powerpc: Fix build by disabling attribute-alias warning for
SYSCALL_DEFINEx").
Signed-off-by: Paul Burton <paul.burton@mips.com>
Acked-by: Christophe Leroy <christophe.leroy@c-s.fr>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull rseq fixes from Thomas Gleixer:
"A pile of rseq related fixups:
- Prevent infinite recursion when delivering SIGSEGV
- Remove the abort of rseq critical section on fork() as syscalls
inside rseq critical sections are explicitely forbidden. So no
point in doing the abort on the child.
- Align the rseq structure on 32 bytes in the ARM selftest code.
- Fix file permissions of the test script"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
rseq: Avoid infinite recursion when delivering SIGSEGV
rseq/cleanup: Do not abort rseq c.s. in child on fork()
rseq/selftests/arm: Align 'struct rseq_cs' on 32 bytes
rseq/selftests: Make run_param_test.sh executable
|
|
When delivering a signal to a task that is using rseq, we call into
__rseq_handle_notify_resume() so that the registers pushed in the
sigframe are updated to reflect the state of the restartable sequence
(for example, ensuring that the signal returns to the abort handler if
necessary).
However, if the rseq management fails due to an unrecoverable fault when
accessing userspace or certain combinations of RSEQ_CS_* flags, then we
will attempt to deliver a SIGSEGV. This has the potential for infinite
recursion if the rseq code continuously fails on signal delivery.
Avoid this problem by using force_sigsegv() instead of force_sig(), which
is explicitly designed to reset the SEGV handler to SIG_DFL in the case
of a recursive fault. In doing so, remove rseq_signal_deliver() from the
internal rseq API and have an optional struct ksignal * parameter to
rseq_handle_notify_resume() instead.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: peterz@infradead.org
Cc: paulmck@linux.vnet.ibm.com
Cc: boqun.feng@gmail.com
Link: https://lkml.kernel.org/r/1529664307-983-1-git-send-email-will.deacon@arm.com
|
|
I broke the build when CONFIG_NMI_IPI=n with my recent commit to add
arch_trigger_cpumask_backtrace(), eg:
stacktrace.c:(.text+0x1b0): undefined reference to `.smp_send_safe_nmi_ipi'
We should rework the CONFIG symbols here in future to avoid these
double barrelled ifdefs but for now they fix the build.
Fixes: 5cc05910f26e ("powerpc/64s: Wire up arch_trigger_cpumask_backtrace()")
Reported-by: Christophe LEROY <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Similar to previous patches, hard disable interrupts when a CPU is
in panic. This reduces the chance the watchdog has to interfere with
the panic, and avoids any other type of masked interrupt being
executed when crashing which minimises the length of the crash path.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Marking CPUs stopped by smp_send_stop as offline can cause warnings
due to cross-CPU wakeups. This trace was noticed on a busy system
running a sysrq+c crash test, after the injected crash:
WARNING: CPU: 51 PID: 1546 at kernel/sched/core.c:1179 set_task_cpu+0x22c/0x240
CPU: 51 PID: 1546 Comm: kworker/u352:1 Tainted: G D
Workqueue: mlx5e mlx5e_update_stats_work [mlx5_core]
[...]
NIP [c00000000017c21c] set_task_cpu+0x22c/0x240
LR [c00000000017d580] try_to_wake_up+0x230/0x720
Call Trace:
[c000000001017700] runqueues+0x0/0xb00 (unreliable)
[c00000000017d580] try_to_wake_up+0x230/0x720
[c00000000015a214] insert_work+0x104/0x140
[c00000000015adb0] __queue_work+0x230/0x690
[c000003fc5007910] [c00000000015b26c] queue_work_on+0x5c/0x90
[c0080000135fc8f8] mlx5_cmd_exec+0x538/0xcb0 [mlx5_core]
[c008000013608fd0] mlx5_core_access_reg+0x140/0x1d0 [mlx5_core]
[c00800001362777c] mlx5e_update_pport_counters.constprop.59+0x6c/0x90 [mlx5_core]
[c008000013628868] mlx5e_update_ndo_stats+0x28/0x90 [mlx5_core]
[c008000013625558] mlx5e_update_stats_work+0x68/0xb0 [mlx5_core]
[c00000000015bcec] process_one_work+0x1bc/0x5f0
[c00000000015ecac] worker_thread+0xac/0x6b0
[c000000000168338] kthread+0x168/0x1b0
[c00000000000b628] ret_from_kernel_thread+0x5c/0xb4
This happens because firstly the CPU is not really offline in the
usual sense, processes and interrupts have not been migrated away.
Secondly smp_send_stop does not happen atomically on all CPUs, so
one CPU can have marked itself offline, while another CPU is still
running processes or interrupts which can affect the first CPU.
Fix this by just not marking the CPU as offline. It's more like
frozen in time, so offline does not really reflect its state properly
anyway. There should be nothing in the crash/panic path that walks
online CPUs and synchronously waits for them, so this change should
not introduce new hangs.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Similarly to commit 855bfe0de1 ("powerpc: hard disable irqs in
smp_send_stop loop"), irqs should be hard disabled by
panic_smp_self_stop.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
In the device tree CPU features quirk code we want to set
CPU_FTR_POWER9_DD2_1 on all Power9s that aren't DD2.0 or earlier. But
we got the logic wrong and instead set it on all CPUs that aren't
Power9 DD2.0 or earlier, ie. including Power8.
Fix it by making sure we're on a Power9. This isn't a bug in practice
because the only code that checks the feature is Power9 only to begin
with. But we'll backport it anyway to avoid confusion.
Fixes: 9e9626ed3a4a ("powerpc/64s: Fix POWER9 DD2.2 and above in DT CPU features")
Cc: stable@vger.kernel.org # v4.17+
Reported-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Acked-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc into HEAD
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull more Kbuild updates from Masahiro Yamada:
- fix some bugs introduced by the recent Kconfig syntax extension
- add some symbols about compiler information in Kconfig, such as
CC_IS_GCC, CC_IS_CLANG, GCC_VERSION, etc.
- test compiler capability for the stack protector in Kconfig, and
clean-up Makefile
- test compiler capability for GCC-plugins in Kconfig, and clean-up
Makefile
- allow to enable GCC-plugins for COMPILE_TEST
- test compiler capability for KCOV in Kconfig and correct dependency
- remove auto-detect mode of the GCOV format, which is now more nicely
handled in Kconfig
- test compiler capability for mprofile-kernel on PowerPC, and clean-up
Makefile
- misc cleanups
* tag 'kbuild-v4.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
linux/linkage.h: replace VMLINUX_SYMBOL_STR() with __stringify()
kconfig: fix localmodconfig
sh: remove no-op macro VMLINUX_SYMBOL()
powerpc/kbuild: move -mprofile-kernel check to Kconfig
Documentation: kconfig: add recommended way to describe compiler support
gcc-plugins: disable GCC_PLUGIN_STRUCTLEAK_BYREF_ALL for COMPILE_TEST
gcc-plugins: allow to enable GCC_PLUGINS for COMPILE_TEST
gcc-plugins: test plugin support in Kconfig and clean up Makefile
gcc-plugins: move GCC version check for PowerPC to Kconfig
kcov: test compiler capability in Kconfig and correct dependency
gcov: remove CONFIG_GCOV_FORMAT_AUTODETECT
arm64: move GCC version check for ARCH_SUPPORTS_INT128 to Kconfig
kconfig: add CC_IS_CLANG and CLANG_VERSION
kconfig: add CC_IS_GCC and GCC_VERSION
stack-protector: test compiler capability in Kconfig and drop AUTO mode
kbuild: fix endless syncconfig in case arch Makefile sets CROSS_COMPILE
|
|
The vmalloc() function has no 2-factor argument form, so multiplication
factors need to be wrapped in array_size(). This patch replaces cases of:
vmalloc(a * b)
with:
vmalloc(array_size(a, b))
as well as handling cases of:
vmalloc(a * b * c)
with:
vmalloc(array3_size(a, b, c))
This does, however, attempt to ignore constant size factors like:
vmalloc(4 * 1024)
though any constants defined via macros get caught up in the conversion.
Any factors with a sizeof() of "unsigned char", "char", and "u8" were
dropped, since they're redundant.
The Coccinelle script used for this was:
// Fix redundant parens around sizeof().
@@
type TYPE;
expression THING, E;
@@
(
vmalloc(
- (sizeof(TYPE)) * E
+ sizeof(TYPE) * E
, ...)
|
vmalloc(
- (sizeof(THING)) * E
+ sizeof(THING) * E
, ...)
)
// Drop single-byte sizes and redundant parens.
@@
expression COUNT;
typedef u8;
typedef __u8;
@@
(
vmalloc(
- sizeof(u8) * (COUNT)
+ COUNT
, ...)
|
vmalloc(
- sizeof(__u8) * (COUNT)
+ COUNT
, ...)
|
vmalloc(
- sizeof(char) * (COUNT)
+ COUNT
, ...)
|
vmalloc(
- sizeof(unsigned char) * (COUNT)
+ COUNT
, ...)
|
vmalloc(
- sizeof(u8) * COUNT
+ COUNT
, ...)
|
vmalloc(
- sizeof(__u8) * COUNT
+ COUNT
, ...)
|
vmalloc(
- sizeof(char) * COUNT
+ COUNT
, ...)
|
vmalloc(
- sizeof(unsigned char) * COUNT
+ COUNT
, ...)
)
// 2-factor product with sizeof(type/expression) and identifier or constant.
@@
type TYPE;
expression THING;
identifier COUNT_ID;
constant COUNT_CONST;
@@
(
vmalloc(
- sizeof(TYPE) * (COUNT_ID)
+ array_size(COUNT_ID, sizeof(TYPE))
, ...)
|
vmalloc(
- sizeof(TYPE) * COUNT_ID
+ array_size(COUNT_ID, sizeof(TYPE))
, ...)
|
vmalloc(
- sizeof(TYPE) * (COUNT_CONST)
+ array_size(COUNT_CONST, sizeof(TYPE))
, ...)
|
vmalloc(
- sizeof(TYPE) * COUNT_CONST
+ array_size(COUNT_CONST, sizeof(TYPE))
, ...)
|
vmalloc(
- sizeof(THING) * (COUNT_ID)
+ array_size(COUNT_ID, sizeof(THING))
, ...)
|
vmalloc(
- sizeof(THING) * COUNT_ID
+ array_size(COUNT_ID, sizeof(THING))
, ...)
|
vmalloc(
- sizeof(THING) * (COUNT_CONST)
+ array_size(COUNT_CONST, sizeof(THING))
, ...)
|
vmalloc(
- sizeof(THING) * COUNT_CONST
+ array_size(COUNT_CONST, sizeof(THING))
, ...)
)
// 2-factor product, only identifiers.
@@
identifier SIZE, COUNT;
@@
vmalloc(
- SIZE * COUNT
+ array_size(COUNT, SIZE)
, ...)
// 3-factor product with 1 sizeof(type) or sizeof(expression), with
// redundant parens removed.
@@
expression THING;
identifier STRIDE, COUNT;
type TYPE;
@@
(
vmalloc(
- sizeof(TYPE) * (COUNT) * (STRIDE)
+ array3_size(COUNT, STRIDE, sizeof(TYPE))
, ...)
|
vmalloc(
- sizeof(TYPE) * (COUNT) * STRIDE
+ array3_size(COUNT, STRIDE, sizeof(TYPE))
, ...)
|
vmalloc(
- sizeof(TYPE) * COUNT * (STRIDE)
+ array3_size(COUNT, STRIDE, sizeof(TYPE))
, ...)
|
vmalloc(
- sizeof(TYPE) * COUNT * STRIDE
+ array3_size(COUNT, STRIDE, sizeof(TYPE))
, ...)
|
vmalloc(
- sizeof(THING) * (COUNT) * (STRIDE)
+ array3_size(COUNT, STRIDE, sizeof(THING))
, ...)
|
vmalloc(
- sizeof(THING) * (COUNT) * STRIDE
+ array3_size(COUNT, STRIDE, sizeof(THING))
, ...)
|
vmalloc(
- sizeof(THING) * COUNT * (STRIDE)
+ array3_size(COUNT, STRIDE, sizeof(THING))
, ...)
|
vmalloc(
- sizeof(THING) * COUNT * STRIDE
+ array3_size(COUNT, STRIDE, sizeof(THING))
, ...)
)
// 3-factor product with 2 sizeof(variable), with redundant parens removed.
@@
expression THING1, THING2;
identifier COUNT;
type TYPE1, TYPE2;
@@
(
vmalloc(
- sizeof(TYPE1) * sizeof(TYPE2) * COUNT
+ array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2))
, ...)
|
vmalloc(
- sizeof(TYPE1) * sizeof(THING2) * (COUNT)
+ array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2))
, ...)
|
vmalloc(
- sizeof(THING1) * sizeof(THING2) * COUNT
+ array3_size(COUNT, sizeof(THING1), sizeof(THING2))
, ...)
|
vmalloc(
- sizeof(THING1) * sizeof(THING2) * (COUNT)
+ array3_size(COUNT, sizeof(THING1), sizeof(THING2))
, ...)
|
vmalloc(
- sizeof(TYPE1) * sizeof(THING2) * COUNT
+ array3_size(COUNT, sizeof(TYPE1), sizeof(THING2))
, ...)
|
vmalloc(
- sizeof(TYPE1) * sizeof(THING2) * (COUNT)
+ array3_size(COUNT, sizeof(TYPE1), sizeof(THING2))
, ...)
)
// 3-factor product, only identifiers, with redundant parens removed.
@@
identifier STRIDE, SIZE, COUNT;
@@
(
vmalloc(
- (COUNT) * STRIDE * SIZE
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
vmalloc(
- COUNT * (STRIDE) * SIZE
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
vmalloc(
- COUNT * STRIDE * (SIZE)
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
vmalloc(
- (COUNT) * (STRIDE) * SIZE
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
vmalloc(
- COUNT * (STRIDE) * (SIZE)
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
vmalloc(
- (COUNT) * STRIDE * (SIZE)
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
vmalloc(
- (COUNT) * (STRIDE) * (SIZE)
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
vmalloc(
- COUNT * STRIDE * SIZE
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
)
// Any remaining multi-factor products, first at least 3-factor products
// when they're not all constants...
@@
expression E1, E2, E3;
constant C1, C2, C3;
@@
(
vmalloc(C1 * C2 * C3, ...)
|
vmalloc(
- E1 * E2 * E3
+ array3_size(E1, E2, E3)
, ...)
)
// And then all remaining 2 factors products when they're not all constants.
@@
expression E1, E2;
constant C1, C2;
@@
(
vmalloc(C1 * C2, ...)
|
vmalloc(
- E1 * E2
+ array_size(E1, E2)
, ...)
)
Signed-off-by: Kees Cook <keescook@chromium.org>
|
|
The kzalloc() function has a 2-factor argument form, kcalloc(). This
patch replaces cases of:
kzalloc(a * b, gfp)
with:
kcalloc(a * b, gfp)
as well as handling cases of:
kzalloc(a * b * c, gfp)
with:
kzalloc(array3_size(a, b, c), gfp)
as it's slightly less ugly than:
kzalloc_array(array_size(a, b), c, gfp)
This does, however, attempt to ignore constant size factors like:
kzalloc(4 * 1024, gfp)
though any constants defined via macros get caught up in the conversion.
Any factors with a sizeof() of "unsigned char", "char", and "u8" were
dropped, since they're redundant.
The Coccinelle script used for this was:
// Fix redundant parens around sizeof().
@@
type TYPE;
expression THING, E;
@@
(
kzalloc(
- (sizeof(TYPE)) * E
+ sizeof(TYPE) * E
, ...)
|
kzalloc(
- (sizeof(THING)) * E
+ sizeof(THING) * E
, ...)
)
// Drop single-byte sizes and redundant parens.
@@
expression COUNT;
typedef u8;
typedef __u8;
@@
(
kzalloc(
- sizeof(u8) * (COUNT)
+ COUNT
, ...)
|
kzalloc(
- sizeof(__u8) * (COUNT)
+ COUNT
, ...)
|
kzalloc(
- sizeof(char) * (COUNT)
+ COUNT
, ...)
|
kzalloc(
- sizeof(unsigned char) * (COUNT)
+ COUNT
, ...)
|
kzalloc(
- sizeof(u8) * COUNT
+ COUNT
, ...)
|
kzalloc(
- sizeof(__u8) * COUNT
+ COUNT
, ...)
|
kzalloc(
- sizeof(char) * COUNT
+ COUNT
, ...)
|
kzalloc(
- sizeof(unsigned char) * COUNT
+ COUNT
, ...)
)
// 2-factor product with sizeof(type/expression) and identifier or constant.
@@
type TYPE;
expression THING;
identifier COUNT_ID;
constant COUNT_CONST;
@@
(
- kzalloc
+ kcalloc
(
- sizeof(TYPE) * (COUNT_ID)
+ COUNT_ID, sizeof(TYPE)
, ...)
|
- kzalloc
+ kcalloc
(
- sizeof(TYPE) * COUNT_ID
+ COUNT_ID, sizeof(TYPE)
, ...)
|
- kzalloc
+ kcalloc
(
- sizeof(TYPE) * (COUNT_CONST)
+ COUNT_CONST, sizeof(TYPE)
, ...)
|
- kzalloc
+ kcalloc
(
- sizeof(TYPE) * COUNT_CONST
+ COUNT_CONST, sizeof(TYPE)
, ...)
|
- kzalloc
+ kcalloc
(
- sizeof(THING) * (COUNT_ID)
+ COUNT_ID, sizeof(THING)
, ...)
|
- kzalloc
+ kcalloc
(
- sizeof(THING) * COUNT_ID
+ COUNT_ID, sizeof(THING)
, ...)
|
- kzalloc
+ kcalloc
(
- sizeof(THING) * (COUNT_CONST)
+ COUNT_CONST, sizeof(THING)
, ...)
|
- kzalloc
+ kcalloc
(
- sizeof(THING) * COUNT_CONST
+ COUNT_CONST, sizeof(THING)
, ...)
)
// 2-factor product, only identifiers.
@@
identifier SIZE, COUNT;
@@
- kzalloc
+ kcalloc
(
- SIZE * COUNT
+ COUNT, SIZE
, ...)
// 3-factor product with 1 sizeof(type) or sizeof(expression), with
// redundant parens removed.
@@
expression THING;
identifier STRIDE, COUNT;
type TYPE;
@@
(
kzalloc(
- sizeof(TYPE) * (COUNT) * (STRIDE)
+ array3_size(COUNT, STRIDE, sizeof(TYPE))
, ...)
|
kzalloc(
- sizeof(TYPE) * (COUNT) * STRIDE
+ array3_size(COUNT, STRIDE, sizeof(TYPE))
, ...)
|
kzalloc(
- sizeof(TYPE) * COUNT * (STRIDE)
+ array3_size(COUNT, STRIDE, sizeof(TYPE))
, ...)
|
kzalloc(
- sizeof(TYPE) * COUNT * STRIDE
+ array3_size(COUNT, STRIDE, sizeof(TYPE))
, ...)
|
kzalloc(
- sizeof(THING) * (COUNT) * (STRIDE)
+ array3_size(COUNT, STRIDE, sizeof(THING))
, ...)
|
kzalloc(
- sizeof(THING) * (COUNT) * STRIDE
+ array3_size(COUNT, STRIDE, sizeof(THING))
, ...)
|
kzalloc(
- sizeof(THING) * COUNT * (STRIDE)
+ array3_size(COUNT, STRIDE, sizeof(THING))
, ...)
|
kzalloc(
- sizeof(THING) * COUNT * STRIDE
+ array3_size(COUNT, STRIDE, sizeof(THING))
, ...)
)
// 3-factor product with 2 sizeof(variable), with redundant parens removed.
@@
expression THING1, THING2;
identifier COUNT;
type TYPE1, TYPE2;
@@
(
kzalloc(
- sizeof(TYPE1) * sizeof(TYPE2) * COUNT
+ array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2))
, ...)
|
kzalloc(
- sizeof(TYPE1) * sizeof(THING2) * (COUNT)
+ array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2))
, ...)
|
kzalloc(
- sizeof(THING1) * sizeof(THING2) * COUNT
+ array3_size(COUNT, sizeof(THING1), sizeof(THING2))
, ...)
|
kzalloc(
- sizeof(THING1) * sizeof(THING2) * (COUNT)
+ array3_size(COUNT, sizeof(THING1), sizeof(THING2))
, ...)
|
kzalloc(
- sizeof(TYPE1) * sizeof(THING2) * COUNT
+ array3_size(COUNT, sizeof(TYPE1), sizeof(THING2))
, ...)
|
kzalloc(
- sizeof(TYPE1) * sizeof(THING2) * (COUNT)
+ array3_size(COUNT, sizeof(TYPE1), sizeof(THING2))
, ...)
)
// 3-factor product, only identifiers, with redundant parens removed.
@@
identifier STRIDE, SIZE, COUNT;
@@
(
kzalloc(
- (COUNT) * STRIDE * SIZE
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
kzalloc(
- COUNT * (STRIDE) * SIZE
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
kzalloc(
- COUNT * STRIDE * (SIZE)
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
kzalloc(
- (COUNT) * (STRIDE) * SIZE
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
kzalloc(
- COUNT * (STRIDE) * (SIZE)
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
kzalloc(
- (COUNT) * STRIDE * (SIZE)
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
kzalloc(
- (COUNT) * (STRIDE) * (SIZE)
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
kzalloc(
- COUNT * STRIDE * SIZE
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
)
// Any remaining multi-factor products, first at least 3-factor products,
// when they're not all constants...
@@
expression E1, E2, E3;
constant C1, C2, C3;
@@
(
kzalloc(C1 * C2 * C3, ...)
|
kzalloc(
- (E1) * E2 * E3
+ array3_size(E1, E2, E3)
, ...)
|
kzalloc(
- (E1) * (E2) * E3
+ array3_size(E1, E2, E3)
, ...)
|
kzalloc(
- (E1) * (E2) * (E3)
+ array3_size(E1, E2, E3)
, ...)
|
kzalloc(
- E1 * E2 * E3
+ array3_size(E1, E2, E3)
, ...)
)
// And then all remaining 2 factors products when they're not all constants,
// keeping sizeof() as the second factor argument.
@@
expression THING, E1, E2;
type TYPE;
constant C1, C2, C3;
@@
(
kzalloc(sizeof(THING) * C2, ...)
|
kzalloc(sizeof(TYPE) * C2, ...)
|
kzalloc(C1 * C2 * C3, ...)
|
kzalloc(C1 * C2, ...)
|
- kzalloc
+ kcalloc
(
- sizeof(TYPE) * (E2)
+ E2, sizeof(TYPE)
, ...)
|
- kzalloc
+ kcalloc
(
- sizeof(TYPE) * E2
+ E2, sizeof(TYPE)
, ...)
|
- kzalloc
+ kcalloc
(
- sizeof(THING) * (E2)
+ E2, sizeof(THING)
, ...)
|
- kzalloc
+ kcalloc
(
- sizeof(THING) * E2
+ E2, sizeof(THING)
, ...)
|
- kzalloc
+ kcalloc
(
- (E1) * E2
+ E1, E2
, ...)
|
- kzalloc
+ kcalloc
(
- (E1) * (E2)
+ E1, E2
, ...)
|
- kzalloc
+ kcalloc
(
- E1 * E2
+ E1, E2
, ...)
)
Signed-off-by: Kees Cook <keescook@chromium.org>
|
|
This eliminates the workaround that requires disabling
-mprofile-kernel by default in Kconfig.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull restartable sequence support from Thomas Gleixner:
"The restartable sequences syscall (finally):
After a lot of back and forth discussion and massive delays caused by
the speculative distraction of maintainers, the core set of
restartable sequences has finally reached a consensus.
It comes with the basic non disputed core implementation along with
support for arm, powerpc and x86 and a full set of selftests
It was exposed to linux-next earlier this week, so it does not fully
comply with the merge window requirements, but there is really no
point to drag it out for yet another cycle"
* 'core-rseq-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
rseq/selftests: Provide Makefile, scripts, gitignore
rseq/selftests: Provide parametrized tests
rseq/selftests: Provide basic percpu ops test
rseq/selftests: Provide basic test
rseq/selftests: Provide rseq library
selftests/lib.mk: Introduce OVERRIDE_TARGETS
powerpc: Wire up restartable sequences system call
powerpc: Add syscall detection for restartable sequences
powerpc: Add support for restartable sequences
x86: Wire up restartable sequence system call
x86: Add support for restartable sequences
arm: Wire up restartable sequences system call
arm: Add syscall detection for restartable sequences
arm: Add restartable sequences support
rseq: Introduce restartable sequences system call
uapi/headers: Provide types_32_64.h
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Notable changes:
- Support for split PMD page table lock on 64-bit Book3S (Power8/9).
- Add support for HAVE_RELIABLE_STACKTRACE, so we properly support
live patching again.
- Add support for patching barrier_nospec in copy_from_user() and
syscall entry.
- A couple of fixes for our data breakpoints on Book3S.
- A series from Nick optimising TLB/mm handling with the Radix MMU.
- Numerous small cleanups to squash sparse/gcc warnings from Mathieu
Malaterre.
- Several series optimising various parts of the 32-bit code from
Christophe Leroy.
- Removal of support for two old machines, "SBC834xE" and "C2K"
("GEFanuc,C2K"), which is why the diffstat has so many deletions.
And many other small improvements & fixes.
There's a few out-of-area changes. Some minor ftrace changes OK'ed by
Steve, and a fix to our powernv cpuidle driver. Then there's a series
touching mm, x86 and fs/proc/task_mmu.c, which cleans up some details
around pkey support. It was ack'ed/reviewed by Ingo & Dave and has
been in next for several weeks.
Thanks to: Akshay Adiga, Alastair D'Silva, Alexey Kardashevskiy, Al
Viro, Andrew Donnellan, Aneesh Kumar K.V, Anju T Sudhakar, Arnd
Bergmann, Balbir Singh, Cédric Le Goater, Christophe Leroy, Christophe
Lombard, Colin Ian King, Dave Hansen, Fabio Estevam, Finn Thain,
Frederic Barrat, Gautham R. Shenoy, Haren Myneni, Hari Bathini, Ingo
Molnar, Jonathan Neuschäfer, Josh Poimboeuf, Kamalesh Babulal,
Madhavan Srinivasan, Mahesh Salgaonkar, Mark Greer, Mathieu Malaterre,
Matthew Wilcox, Michael Neuling, Michal Suchanek, Naveen N. Rao,
Nicholas Piggin, Nicolai Stange, Olof Johansson, Paul Gortmaker, Paul
Mackerras, Peter Rosin, Pridhiviraj Paidipeddi, Ram Pai, Rashmica
Gupta, Ravi Bangoria, Russell Currey, Sam Bobroff, Samuel
Mendoza-Jonas, Segher Boessenkool, Shilpasri G Bhat, Simon Guo,
Souptick Joarder, Stewart Smith, Thiago Jung Bauermann, Torsten Duwe,
Vaibhav Jain, Wei Yongjun, Wolfram Sang, Yisheng Xie, YueHaibing"
* tag 'powerpc-4.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (251 commits)
powerpc/64s/radix: Fix missing ptesync in flush_cache_vmap
cpuidle: powernv: Fix promotion from snooze if next state disabled
powerpc: fix build failure by disabling attribute-alias warning in pci_32
ocxl: Fix missing unlock on error in afu_ioctl_enable_p9_wait()
powerpc-opal: fix spelling mistake "Uniterrupted" -> "Uninterrupted"
powerpc: fix spelling mistake: "Usupported" -> "Unsupported"
powerpc/pkeys: Detach execute_only key on !PROT_EXEC
powerpc/powernv: copy/paste - Mask SO bit in CR
powerpc: Remove core support for Marvell mv64x60 hostbridges
powerpc/boot: Remove core support for Marvell mv64x60 hostbridges
powerpc/boot: Remove support for Marvell mv64x60 i2c controller
powerpc/boot: Remove support for Marvell MPSC serial controller
powerpc/embedded6xx: Remove C2K board support
powerpc/lib: optimise PPC32 memcmp
powerpc/lib: optimise 32 bits __clear_user()
powerpc/time: inline arch_vtime_task_switch()
powerpc/Makefile: set -mcpu=860 flag for the 8xx
powerpc: Implement csum_ipv6_magic in assembly
powerpc/32: Optimise __csum_partial()
powerpc/lib: Adjust .balign inside string functions for PPC32
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild updates from Masahiro Yamada:
- improve fixdep to coalesce consecutive slashes in dep-files
- fix some issues of the maintainer string generation in deb-pkg script
- remove unused CONFIG_HAVE_UNDERSCORE_SYMBOL_PREFIX and clean-up
several tools and linker scripts
- clean-up modpost
- allow to enable the dead code/data elimination for PowerPC in EXPERT
mode
- improve two coccinelle scripts for better performance
- pass endianness and machine size flags to sparse for all architecture
- misc fixes
* tag 'kbuild-v4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (25 commits)
kbuild: add machine size to CHECKFLAGS
kbuild: add endianness flag to CHEKCFLAGS
kbuild: $(CHECK) doesnt need NOSTDINC_FLAGS twice
scripts: Fixed printf format mismatch
scripts/tags.sh: use `find` for $ALLSOURCE_ARCHS generation
coccinelle: deref_null: improve performance
coccinelle: mini_lock: improve performance
powerpc: Allow LD_DEAD_CODE_DATA_ELIMINATION to be selected
kbuild: Allow LD_DEAD_CODE_DATA_ELIMINATION to be selectable if enabled
kbuild: LD_DEAD_CODE_DATA_ELIMINATION no -ffunction-sections/-fdata-sections for module build
kbuild: Fix asm-generic/vmlinux.lds.h for LD_DEAD_CODE_DATA_ELIMINATION
modpost: constify *modname function argument where possible
modpost: remove redundant is_vmlinux() test
modpost: use strstarts() helper more widely
modpost: pass struct elf_info pointer to get_modinfo()
checkpatch: remove VMLINUX_SYMBOL() check
vmlinux.lds.h: remove no-op macro VMLINUX_SYMBOL()
kbuild: remove CONFIG_HAVE_UNDERSCORE_SYMBOL_PREFIX
export.h: remove code for prefixing symbols with underscore
depmod.sh: remove symbol prefix support
...
|
|
Syscalls are not allowed inside restartable sequences, so add a call to
rseq_syscall() at the very beginning of system call exiting path for
CONFIG_DEBUG_RSEQ=y kernel. This could help us to detect whether there
is a syscall issued inside restartable sequences.
Signed-off-by: Boqun Feng <boqun.feng@gmail.com>
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Joel Fernandes <joelaf@google.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Dave Watson <davejwatson@fb.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: "H . Peter Anvin" <hpa@zytor.com>
Cc: Chris Lameter <cl@linux.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Andrew Hunter <ahh@google.com>
Cc: Michael Kerrisk <mtk.manpages@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "Paul E . McKenney" <paulmck@linux.vnet.ibm.com>
Cc: Paul Turner <pjt@google.com>
Cc: Josh Triplett <josh@joshtriplett.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Ben Maurer <bmaurer@fb.com>
Cc: linux-api@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: https://lkml.kernel.org/r/20180602124408.8430-10-mathieu.desnoyers@efficios.com
|
|
Call the rseq_handle_notify_resume() function on return to userspace if
TIF_NOTIFY_RESUME thread flag is set.
Perform fixup on the pre-signal when a signal is delivered on top of a
restartable sequence critical section.
Signed-off-by: Boqun Feng <boqun.feng@gmail.com>
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Joel Fernandes <joelaf@google.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Dave Watson <davejwatson@fb.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: "H . Peter Anvin" <hpa@zytor.com>
Cc: Chris Lameter <cl@linux.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Andrew Hunter <ahh@google.com>
Cc: Michael Kerrisk <mtk.manpages@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "Paul E . McKenney" <paulmck@linux.vnet.ibm.com>
Cc: Paul Turner <pjt@google.com>
Cc: Josh Triplett <josh@joshtriplett.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Ben Maurer <bmaurer@fb.com>
Cc: linux-api@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: https://lkml.kernel.org/r/20180602124408.8430-9-mathieu.desnoyers@efficios.com
|
|
Commit 2479bfc9bc600 ("powerpc: Fix build by disabling attribute-alias
warning for SYSCALL_DEFINEx") forgot arch/powerpc/kernel/pci_32.c
Latest GCC version emit the following warnings
As arch/powerpc code is built with -Werror, this breaks build with
GCC 8.1
This patch inhibits this warning
In file included from arch/powerpc/kernel/pci_32.c:14:
./include/linux/syscalls.h:233:18: error: 'sys_pciconfig_iobase' alias between functions of incompatible types 'long int(long int, long unsigned int, long unsigned int)' and 'long int(long int, long int, long int)' [-Werror=attribute-alias]
asmlinkage long sys##name(__MAP(x,__SC_DECL,__VA_ARGS__)) \
^~~
./include/linux/syscalls.h:222:2: note: in expansion of macro '__SYSCALL_DEFINEx'
__SYSCALL_DEFINEx(x, sname, __VA_ARGS__)
^~~~~~~~~~~~~~~~~
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timers and timekeeping updates from Thomas Gleixner:
- Core infrastucture work for Y2038 to address the COMPAT interfaces:
+ Add a new Y2038 safe __kernel_timespec and use it in the core
code
+ Introduce config switches which allow to control the various
compat mechanisms
+ Use the new config switch in the posix timer code to control the
32bit compat syscall implementation.
- Prevent bogus selection of CPU local clocksources which causes an
endless reselection loop
- Remove the extra kthread in the clocksource code which has no value
and just adds another level of indirection
- The usual bunch of trivial updates, cleanups and fixlets all over the
place
- More SPDX conversions
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits)
clocksource/drivers/mxs_timer: Switch to SPDX identifier
clocksource/drivers/timer-imx-tpm: Switch to SPDX identifier
clocksource/drivers/timer-imx-gpt: Switch to SPDX identifier
clocksource/drivers/timer-imx-gpt: Remove outdated file path
clocksource/drivers/arc_timer: Add comments about locking while read GFRC
clocksource/drivers/mips-gic-timer: Add pr_fmt and reword pr_* messages
clocksource/drivers/sprd: Fix Kconfig dependency
clocksource: Move inline keyword to the beginning of function declarations
timer_list: Remove unused function pointer typedef
timers: Adjust a kernel-doc comment
tick: Prefer a lower rating device only if it's CPU local device
clocksource: Remove kthread
time: Change nanosleep to safe __kernel_* types
time: Change types to new y2038 safe __kernel_* types
time: Fix get_timespec64() for y2038 safe compat interfaces
time: Add new y2038 safe __kernel_timespec
posix-timers: Make compat syscalls depend on CONFIG_COMPAT_32BIT_TIME
time: Introduce CONFIG_COMPAT_32BIT_TIME
time: Introduce CONFIG_64BIT_TIME in architectures
compat: Enable compat_get/put_timespec64 always
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace
Pull siginfo updates from Eric Biederman:
"This set of changes close the known issues with setting si_code to an
invalid value, and with not fully initializing struct siginfo. There
remains work to do on nds32, arc, unicore32, powerpc, arm, arm64, ia64
and x86 to get the code that generates siginfo into a simpler and more
maintainable state. Most of that work involves refactoring the signal
handling code and thus careful code review.
Also not included is the work to shrink the in kernel version of
struct siginfo. That depends on getting the number of places that
directly manipulate struct siginfo under control, as it requires the
introduction of struct kernel_siginfo for the in kernel things.
Overall this set of changes looks like it is making good progress, and
with a little luck I will be wrapping up the siginfo work next
development cycle"
* 'siginfo-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace: (46 commits)
signal/sh: Stop gcc warning about an impossible case in do_divide_error
signal/mips: Report FPE_FLTUNK for undiagnosed floating point exceptions
signal/um: More carefully relay signals in relay_signal.
signal: Extend siginfo_layout with SIL_FAULT_{MCEERR|BNDERR|PKUERR}
signal: Remove unncessary #ifdef SEGV_PKUERR in 32bit compat code
signal/signalfd: Add support for SIGSYS
signal/signalfd: Remove __put_user from signalfd_copyinfo
signal/xtensa: Use force_sig_fault where appropriate
signal/xtensa: Consistenly use SIGBUS in do_unaligned_user
signal/um: Use force_sig_fault where appropriate
signal/sparc: Use force_sig_fault where appropriate
signal/sparc: Use send_sig_fault where appropriate
signal/sh: Use force_sig_fault where appropriate
signal/s390: Use force_sig_fault where appropriate
signal/riscv: Replace do_trap_siginfo with force_sig_fault
signal/riscv: Use force_sig_fault where appropriate
signal/parisc: Use force_sig_fault where appropriate
signal/parisc: Use force_sig_mceerr where appropriate
signal/openrisc: Use force_sig_fault where appropriate
signal/nios2: Use force_sig_fault where appropriate
...
|
|
Pull dma-mapping updates from Christoph Hellwig:
- replace the force_dma flag with a dma_configure bus method. (Nipun
Gupta, although one patch is іncorrectly attributed to me due to a
git rebase bug)
- use GFP_DMA32 more agressively in dma-direct. (Takashi Iwai)
- remove PCI_DMA_BUS_IS_PHYS and rely on the dma-mapping API to do the
right thing for bounce buffering.
- move dma-debug initialization to common code, and apply a few
cleanups to the dma-debug code.
- cleanup the Kconfig mess around swiotlb selection
- swiotlb comment fixup (Yisheng Xie)
- a trivial swiotlb fix. (Dan Carpenter)
- support swiotlb on RISC-V. (based on a patch from Palmer Dabbelt)
- add a new generic dma-noncoherent dma_map_ops implementation and use
it for arc, c6x and nds32.
- improve scatterlist validity checking in dma-debug. (Robin Murphy)
- add a struct device quirk to limit the dma-mask to 32-bit due to
bridge/system issues, and switch x86 to use it instead of a local
hack for VIA bridges.
- handle devices without a dma_mask more gracefully in the dma-direct
code.
* tag 'dma-mapping-4.18' of git://git.infradead.org/users/hch/dma-mapping: (48 commits)
dma-direct: don't crash on device without dma_mask
nds32: use generic dma_noncoherent_ops
nds32: implement the unmap_sg DMA operation
nds32: consolidate DMA cache maintainance routines
x86/pci-dma: switch the VIA 32-bit DMA quirk to use the struct device flag
x86/pci-dma: remove the explicit nodac and allowdac option
x86/pci-dma: remove the experimental forcesac boot option
Documentation/x86: remove a stray reference to pci-nommu.c
core, dma-direct: add a flag 32-bit dma limits
dma-mapping: remove unused gfp_t parameter to arch_dma_alloc_attrs
dma-debug: check scatterlist segments
c6x: use generic dma_noncoherent_ops
arc: use generic dma_noncoherent_ops
arc: fix arc_dma_{map,unmap}_page
arc: fix arc_dma_sync_sg_for_{cpu,device}
arc: simplify arc_dma_sync_single_for_{cpu,device}
dma-mapping: provide a generic dma-noncoherent implementation
dma-mapping: simplify Kconfig dependencies
riscv: add swiotlb support
riscv: only enable ZONE_DMA32 for 64-bit
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull procfs updates from Al Viro:
"Christoph's proc_create_... cleanups series"
* 'hch.procfs' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (44 commits)
xfs, proc: hide unused xfs procfs helpers
isdn/gigaset: add back gigaset_procinfo assignment
proc: update SIZEOF_PDE_INLINE_NAME for the new pde fields
tty: replace ->proc_fops with ->proc_show
ide: replace ->proc_fops with ->proc_show
ide: remove ide_driver_proc_write
isdn: replace ->proc_fops with ->proc_show
atm: switch to proc_create_seq_private
atm: simplify procfs code
bluetooth: switch to proc_create_seq_data
netfilter/x_tables: switch to proc_create_seq_private
netfilter/xt_hashlimit: switch to proc_create_{seq,single}_data
neigh: switch to proc_create_seq_data
hostap: switch to proc_create_{seq,single}_data
bonding: switch to proc_create_seq_data
rtc/proc: switch to proc_create_single_data
drbd: switch to proc_create_single
resource: switch to proc_create_seq_data
staging/rtl8192u: simplify procfs code
jfs: simplify procfs code
...
|
|
arch_vtime_task_switch() is a small function which is called
only from vtime_common_task_switch(), so it is worth inlining
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Use fault_in_pages_readable() to prefault user context
instead of open coding
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
reloc_offset() is the same as add_reloc_offset(0)
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Direction is already checked in all calling functions in
include/linux/dma-mapping.h and also in called function __dma_sync()
So really no need to check it once more here.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Replace 'op->type & INSTR_TYPE_MASK' expression with GETTYPE(op->type)
macro.
Signed-off-by: Ravi Bangoria <ravi.bangoria@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
We now have barrier_nospec as mitigation so print it in
cpu_show_spectre_v1() when enabled.
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Our syscall entry is done in assembly so patch in an explicit
barrier_nospec.
Based on a patch by Michal Suchanek.
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Check what firmware told us and enable/disable the barrier_nospec as
appropriate.
We err on the side of enabling the barrier, as it's no-op on older
systems, see the comment for more detail.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Note that unlike RFI which is patched only in kernel the nospec state
reflects settings at the time the module was loaded.
Iterating all modules and re-patching every time the settings change
is not implemented.
Based on lwsync patching.
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Based on the RFI patching. This is required to be able to disable the
speculation barrier.
Only one barrier type is supported and it does nothing when the
firmware does not enable it. Also re-patching modules is not supported
So the only meaningful thing that can be done is patching out the
speculation barrier at boot when the user says it is not wanted.
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
This now has new code in it written by Nick and I, and switch to a
SPDX tag.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
|
|
This allows eg. the RCU stall detector, or the soft/hardlockup
detectors to trigger a backtrace on all CPUs.
We implement this by sending a "safe" NMI, which will actually only
send an IPI. Unfortunately the generic code prints "NMI", so that's a
little confusing but we can probably live with it.
If one of the CPUs doesn't respond to the IPI, we then print some info
from it's paca and do a backtrace based on its saved_r1.
Example output:
INFO: rcu_sched detected stalls on CPUs/tasks:
2-...0: (0 ticks this GP) idle=1be/1/4611686018427387904 softirq=1055/1055 fqs=25735
(detected by 4, t=58847 jiffies, g=58, c=57, q=1258)
Sending NMI from CPU 4 to CPUs 2:
CPU 2 didn't respond to backtrace IPI, inspecting paca.
irq_soft_mask: 0x01 in_mce: 0 in_nmi: 0 current: 3623 (bash)
Back trace of paca->saved_r1 (0xc0000000e1c83ba0) (possibly stale):
Call Trace:
[c0000000e1c83ba0] [0000000000000014] 0x14 (unreliable)
[c0000000e1c83bc0] [c000000000765798] lkdtm_do_action+0x48/0x80
[c0000000e1c83bf0] [c000000000765a40] direct_entry+0x110/0x1b0
[c0000000e1c83c90] [c00000000058e650] full_proxy_write+0x90/0xe0
[c0000000e1c83ce0] [c0000000003aae3c] __vfs_write+0x6c/0x1f0
[c0000000e1c83d80] [c0000000003ab214] vfs_write+0xd4/0x240
[c0000000e1c83dd0] [c0000000003ab5cc] ksys_write+0x6c/0x110
[c0000000e1c83e30] [c00000000000b860] system_call+0x58/0x6c
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
|
|
Currently the options we have for sending NMIs are not necessarily
safe, that is they can potentially interrupt a CPU in a
non-recoverable region of code, meaning the kernel must then panic().
But we'd like to use smp_send_nmi_ipi() to do cross-CPU calls in
situations where we don't want to risk a panic(), because it doesn't
have the requirement that interrupts must be enabled like
smp_call_function().
So add an API for the caller to indicate that it wants to use the NMI
infrastructure, but doesn't want to do anything "unsafe".
Currently that is implemented by not actually calling cause_nmi_ipi(),
instead falling back to an IPI. In future we can pass the safe
parameter down to cause_nmi_ipi() and the individual backends can
potentially take it into account before deciding what to do.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
|
|
A CPU that gets stuck with interrupts hard disable can be difficult to
debug, as on some platforms we have no way to interrupt the CPU to
find out what it's doing.
A stop-gap is to have the CPU save it's stack pointer (r1) in its paca
when it hard disables interrupts. That way if we can't interrupt it,
we can at least trace the stack based on where it last disabled
interrupts.
In some cases that will be total junk, but the stack trace code should
handle that. In the simple case of a CPU that disable interrupts and
then gets stuck in a loop, the stack trace should be informative.
We could clear the saved stack pointer when we enable interrupts, but
that loses information which could be useful if we have nothing else
to go on.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
|
|
set_fs() sets the addr_limit, which is used in access_ok() to
determine if an address is a user or kernel address.
Some code paths use set_fs() to temporarily elevate the addr_limit so
that kernel code can read/write kernel memory as if it were user
memory. That is fine as long as the code can't ever return to
userspace with the addr_limit still elevated.
If that did happen, then userspace can read/write kernel memory as if
it were user memory, eg. just with write(2). In case it's not clear,
that is very bad. It has also happened in the past due to bugs.
Commit 5ea0727b163c ("x86/syscalls: Check address limit on user-mode
return") added a mechanism to check the addr_limit value before
returning to userspace. Any call to set_fs() sets a thread flag,
TIF_FSCHECK, and if we see that on the return to userspace we go out
of line to check that the addr_limit value is not elevated.
For further info see the above commit, as well as:
https://lwn.net/Articles/722267/
https://bugs.chromium.org/p/project-zero/issues/detail?id=990
Verified to work on 64-bit Book3S using a POC that objdumps the system
call handler, and a modified lkdtm_CORRUPT_USER_DS() that doesn't kill
the caller.
Before:
$ sudo ./test-tif-fscheck
...
0000000000000000 <.data>:
0: e1 f7 8a 79 rldicl. r10,r12,30,63
4: 80 03 82 40 bne 0x384
8: 00 40 8a 71 andi. r10,r12,16384
c: 78 0b 2a 7c mr r10,r1
10: 10 fd 21 38 addi r1,r1,-752
14: 08 00 c2 41 beq- 0x1c
18: 58 09 2d e8 ld r1,2392(r13)
1c: 00 00 41 f9 std r10,0(r1)
20: 70 01 61 f9 std r11,368(r1)
24: 78 01 81 f9 std r12,376(r1)
28: 70 00 01 f8 std r0,112(r1)
2c: 78 00 41 f9 std r10,120(r1)
30: 20 00 82 41 beq 0x50
34: a6 42 4c 7d mftb r10
After:
$ sudo ./test-tif-fscheck
Killed
And in dmesg:
Invalid address limit on user-mode return
WARNING: CPU: 1 PID: 3689 at ../include/linux/syscalls.h:260 do_notify_resume+0x140/0x170
...
NIP [c00000000001ee50] do_notify_resume+0x140/0x170
LR [c00000000001ee4c] do_notify_resume+0x13c/0x170
Call Trace:
do_notify_resume+0x13c/0x170 (unreliable)
ret_from_except_lite+0x70/0x74
Performance overhead is essentially zero in the usual case, because
the bit is checked as part of the existing _TIF_USER_WORK_MASK check.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
In PPC_PTRACE_GETHWDBGINFO and PPC_PTRACE_SETHWDEBUG we do an
access_ok() check and then __copy_{from,to}_user().
Instead we should just use copy_{from,to}_user() which does all that
for us and is less error prone.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
The EEH report functions now share a fair bit of code around the start
and end of each function.
So factor out as much as possible, and move the traversal into a
custom function. This also allows accurate debug to be generated more
easily.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
[mpe: Format with clang-format]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
If a device without a driver is recovered via EEH, the flag
EEH_DEV_NO_HANDLER is incorrectly left set on the device after
recovery, because the test in eeh_report_resume() for the existence of
a bound driver is done before the flag is cleared. If a driver is
later bound, and EEH experienced again, some of the drivers EEH
handers are not called.
To correct this, clear the flag unconditionally after EEH processing
is complete.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
To ease future refactoring, extract calls to eeh_enable_irq() and
eeh_disable_irq() from the various report functions. This makes
the report functions initial sequences more similar, as well as making
the IRQ changes visible when reading eeh_handle_normal_event().
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
To ease future refactoring, extract setting of the channel state
from the report functions out into their own functions. This increases
the amount of code that is identical across all of the report
functions.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
The same test is done in every EEH report function, so factor it out.
Since eeh_dev_removed() needs to be moved higher up in the file,
simplify it a little while we're at it.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Add a for_each-style macro for iterating through PEs without the
boilerplate required by a traversal function. eeh_pe_next() is now
exported, as it is now used directly in place.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
As EEH event handling progresses, a cumulative result of type
pci_ers_result is built up by (some of) the eeh_report_*() functions
using either:
if (rc == PCI_ERS_RESULT_NEED_RESET) *res = rc;
if (*res == PCI_ERS_RESULT_NONE) *res = rc;
or:
if ((*res == PCI_ERS_RESULT_NONE) ||
(*res == PCI_ERS_RESULT_RECOVERED)) *res = rc;
if (*res == PCI_ERS_RESULT_DISCONNECT &&
rc == PCI_ERS_RESULT_NEED_RESET) *res = rc;
(Where *res is the accumulator.)
However, the intent is not immediately clear and the result in some
situations is order dependent.
Address this by assigning a priority to each result value, and always
merging to the highest priority. This renders the intent clear, and
provides a stable value for all orderings.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
[mpe: Minor formatting (clang-format)]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
Linus Torvalds
Hari Vyas
Gautham R. Shenoy
Paul Burton
Will Deacon
Michael Ellerman
Nicholas Piggin
Paolo Bonzini
Kees Cook
Boqun Feng
Christophe Leroy
Ravi Bangoria
Michal Suchanek
Al Viro
Sam Bobroff