| Age | Commit message (Collapse) | Author |
|---|
|
This is the 5.2.59 stable release
|
|
commit bbe28fc3cbabbef781bcdf847615d52ce2e26e42 upstream.
hi3660-hikey960.dts:
Define a 'ports' node for 'adv7533: adv7533@39' and the
'adi,dsi-lanes' property to make it compliant with the adi,adv7533 DT
binding.
This fills the requirements to meet the binding requirements,
remote endpoints are not defined.
hi6220-hikey.dts:
Change property name s/pd-gpio/pd-gpios, gpio properties should be
plural. This is just a cosmetic change.
Signed-off-by: Ricardo Cañuelo <ricardo.canuelo@collabora.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit b072714bfc0e42c984b8fd6e069f3ca17de8137a upstream.
Once regulators are disabled after kernel boot, on Espresso board silent
hang observed because of LDO7 being disabled. LDO7 actually provide
power to CPU cores and non-cpu blocks circuitries. Keep this regulator
always-on to fix this hang.
Fixes: 9589f7721e16 ("arm64: dts: Add S2MPS15 PMIC node on exynos7-espresso")
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 1b6a1a162defe649c5599d661b58ac64bb6f31b6 upstream.
msm8916-pins.dtsi specifies "bias-pull-none" for most of the audio
pin configurations. This was likely copied from the qcom kernel fork
where the same property was used for these audio pins.
However, "bias-pull-none" actually does not exist at all - not in
mainline and not in downstream. I can only guess that the original
intention was to configure "no pull", i.e. bias-disable.
Change it to that instead.
Fixes: 143bb9ad85b7 ("arm64: dts: qcom: add audio pinctrls")
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200605185916.318494-2-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 8a445086f8af0b7b9bd8d1901d6f306bb154f70d upstream.
The puma gmac node currently uses opposite active-values for the
gmac phy reset pin. The gpio-declaration uses active-high while the
separate snps,reset-active-low property marks the pin as active low.
While on the kernel side this works ok, other DT users may get
confused - as seen with uboot right now.
So bring this in line and make both properties match, similar to the
other Rockchip board.
Fixes: 2c66fc34e945 ("arm64: dts: rockchip: add RK3399-Q7 (Puma) SoM")
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Link: https://lore.kernel.org/r/20200603132836.362519-1-heiko@sntech.de
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 7a7184f6cfa9279f1a1c10a1845d247d7fad54ff upstream.
The puma vcc5v0_host regulator node currently uses opposite active-values
for the enable pin. The gpio-declaration uses active-high while the
separate enable-active-low property marks the pin as active low.
While on the kernel side this works ok, other DT users may get
confused - as seen with uboot right now.
So bring this in line and make both properties match, similar to the
gmac fix.
Fixes: 2c66fc34e945 ("arm64: dts: rockchip: add RK3399-Q7 (Puma) SoM")
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Link: https://lore.kernel.org/r/20200604091239.424318-1-heiko@sntech.de
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 2300e6dab473e93181cf76e4fe6671aa3d24c57b upstream.
The lion gmac node currently uses opposite active-values for the
gmac phy reset pin. The gpio-declaration uses active-high while the
separate snps,reset-active-low property marks the pin as active low.
While on the kernel side this works ok, other DT users may get
confused - as seen with uboot right now.
So bring this in line and make both properties match, similar to the
other Rockchip board.
Fixes: d99a02bcfa81 ("arm64: dts: rockchip: add RK3368-uQ7 (Lion) SoM")
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Link: https://lore.kernel.org/r/20200607212909.920575-1-heiko@sntech.de
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
This is the 5.2.53 stable release
|
|
commit b2037dafcf082cd24b88ae9283af628235df36e1 upstream.
When starting at 744MHz, the Mali 450 core crashes on S805X based boards:
lima d00c0000.gpu: IRQ ppmmu3 not found
lima d00c0000.gpu: IRQ ppmmu4 not found
lima d00c0000.gpu: IRQ ppmmu5 not found
lima d00c0000.gpu: IRQ ppmmu6 not found
lima d00c0000.gpu: IRQ ppmmu7 not found
Internal error: synchronous external abort: 96000210 [#1] PREEMPT SMP
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.7.2+ #492
Hardware name: Libre Computer AML-S805X-AC (DT)
pstate: 40000005 (nZcv daif -PAN -UAO)
pc : lima_gp_init+0x28/0x188
...
Call trace:
lima_gp_init+0x28/0x188
lima_device_init+0x334/0x534
lima_pdev_probe+0xa4/0xe4
...
Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b
Reverting to a safer 666Mhz frequency on the S805X that doesn't use the
GP0 PLL makes it more stable.
Fixes: fd47716479f5 ("ARM64: dts: add S805X based P241 board")
Fixes: 0449b8e371ac ("arm64: dts: meson: add libretech aml-s805x-ac board")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20200618132737.14243-1-narmstrong@baylibre.com
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 95ca6f06dd4827ff63be5154120c7a8511cd9a41 upstream.
The peripheral clock of the RNG is missing for gxl while it is present
for gxbb.
Fixes: 1b3f6d148692 ("ARM64: dts: meson-gx: add clock CLKID_RNG0 to hwrng node")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20200617125346.1163527-1-jbrunet@baylibre.com
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit a81bcfb6ac20cdd2e8dec3da14c8bbe1d18f6321 upstream.
When high load on the DWC3 SuperSpeed port, the controller crashes with:
[ 221.141621] xhci-hcd xhci-hcd.0.auto: xHCI host not responding to stop endpoint command.
[ 221.157631] xhci-hcd xhci-hcd.0.auto: Host halt failed, -110
[ 221.157635] xhci-hcd xhci-hcd.0.auto: xHCI host controller not responding, assume dead
[ 221.159901] xhci-hcd xhci-hcd.0.auto: xHCI host not responding to stop endpoint command.
[ 221.159961] hub 2-1.1:1.0: hub_ext_port_status failed (err = -22)
[ 221.160076] xhci-hcd xhci-hcd.0.auto: HC died; cleaning up
[ 221.165946] usb 2-1.1-port1: cannot reset (err = -22)
Setting the parkmode_disable_ss_quirk quirk fixes the issue.
Reported-by: Tim <elatllat@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Cc: Jianxin Pan <jianxin.pan@amlogic.com>
CC: Dongjin Kim <tobetter@gmail.com>
Link: https://lore.kernel.org/r/20200221091532.8142-4-narmstrong@baylibre.com
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
This is the 5.2.49 stable release
|
|
commit bba25915b172c72f6fa635f091624d799e3c9cae upstream.
The 'phy-mode' property is currently defined as 'rgmii' for Jetson
Xavier. This indicates that the RGMII RX and TX delays are set by the
MAC and the internal delays set by the PHY are not used.
If the Marvell PHY driver is enabled, such that it is used and not the
generic PHY, ethernet failures are seen (DHCP is failing to obtain an
IP address) and this is caused because the Marvell PHY driver is
disabling the internal RX and TX delays. For Jetson Xavier the internal
PHY RX and TX delay should be used and so fix this by setting the
'phy-mode' to 'rgmii-id' and not 'rgmii'.
Fixes: f89b58ce71a9 ("arm64: tegra: Add ethernet controller on Tegra194")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 4a4a26317ec8aba575f6b85789a42639937bc1a4 upstream.
Each IRQ_TYPE_NONE interrupt causes a warning at boot.
Fix that by defining an appropriate type.
Fixes: e0531312e78f ("arm64: dts: qcom: msm8996: Add CAMSS support")
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Link: https://lore.kernel.org/r/1587470425-13726-1-git-send-email-loic.poulain@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit fe2aff0c574d206f34f1864d5a0b093694c27142 upstream.
The thermal trip points have unit name but no reg property, so we can
remove them. It also fixes the following warnings from 'make dtbs_check'
after adding the thermal yaml bindings.
arch/arm64/boot/dts/qcom/apq8016-sbc.dt.yaml: thermal-zones:
gpu-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/apq8016-sbc.dt.yaml: thermal-zones:
camera-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/apq8016-sbc.dt.yaml: thermal-zones:
modem-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8916-mtp.dt.yaml: thermal-zones:
gpu-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8916-mtp.dt.yaml: thermal-zones:
camera-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8916-mtp.dt.yaml: thermal-zones:
modem-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Link: https://lore.kernel.org/r/2d3d045c18a2fb85b28cf304aa11ae6e6538d75e.1585562459.git.amit.kucheria@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 72b29215aced394d01ca25e432963b619daa0098 upstream.
Fixing several unit name warnings:
Warning (unit_address_vs_reg): /oscillator@0: node has a unit name, but no reg property
Warning (unit_address_vs_reg): /oscillator@1: node has a unit name, but no reg property
Warning (unit_address_vs_reg): /oscillator@2: node has a unit name, but no reg property
Warning (unit_address_vs_reg): /thermal-zones/cpu_thermal/trips/trip-point@0: node has a unit name, but no reg property
Warning (unit_address_vs_reg): /thermal-zones/cpu_thermal/trips/trip-point@1: node has a unit name, but no reg property
Warning (unit_address_vs_reg): /thermal-zones/cpu_thermal/trips/cpu_crit@0: node has a unit name, but no reg property
Warning (unit_address_vs_reg): /thermal-zones/cpu_thermal/cooling-maps/map@0: node has a unit name, but no reg property
Warning (unit_address_vs_reg): /thermal-zones/cpu_thermal/cooling-maps/map@1: node has a unit name, but no reg property
Warning (unit_address_vs_reg): /reserved-memory/vpu_dma_mem_region: node has a reg or ranges property, but no unit name
Warning (simple_bus_reg): /soc/pinctrl@10005000: simple-bus unit address format error, expected "1000b000"
Warning (simple_bus_reg): /soc/interrupt-controller@10220000: simple-bus unit address format error, expected "10221000"
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Link: https://lore.kernel.org/r/20200210063523.133333-4-hsinyi@chromium.org
[mb: drop fixes for '_' in property name]
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 78631aecc52c4b2adcf611769df2ff9c67ac16d0 upstream.
The GIC DT nodes for the fastmodels were not fully compliant with the
DT binding, which has certain expectations about child nodes and their
size and address cells values.
Use smaller #address-cells and #size-cells values, as the binding
requests, and adjust the reg properties accordingly.
This requires adjusting the interrupt nexus nodes as well, as one
field of the interrupt-map property depends on the GIC's address-size.
Since the .dts files share interrupt nexus nodes across different
interrupt controllers (GICv2 vs. GICv3), we need to use the only
commonly allowed #address-size value of <1> for both.
Link: https://lore.kernel.org/r/20200513103016.130417-11-andre.przywara@arm.com
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit a78aee9e434932a500db36cc6d88daeff3745e9f upstream.
The GIC DT nodes for the Juno boards were not fully compliant with
the DT binding, which has certain expectations about child nodes and
their size and address cells values.
Use smaller #address-cells and #size-cells values, as the binding
requests, and adjust the reg properties accordingly.
This requires adjusting the interrupt nexus nodes as well, as one
field of the interrupt-map property depends on the GIC's address-size.
Link: https://lore.kernel.org/r/20200513103016.130417-10-andre.przywara@arm.com
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit bb5cce12ac717c7462217cd493ed701d12d6dbce upstream.
The Arm Ltd. boards were using an outdated address convention in the DT
node names, by separating the high from the low 32-bits of an address by
a comma.
Remove the comma from the node name suffix to be DT spec compliant.
Link: https://lore.kernel.org/r/20200513103016.130417-3-andre.przywara@arm.com
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 9ecded10b4b6af238da0c86197b0418912e7513e upstream.
The GX and AXG SCP sram nodes were using invalid compatible and
node names for the sram entries.
Fixup the sram entries node names, and use proper compatible for them.
It notably fixes:
sram@c8000000: 'scp-shmem@0', 'scp-shmem@200' do not match any of the regexes: '^([a-z]*-)?sram(-section)?@[a-f0-9]+$', 'pinctrl-[0-9]+'
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20200326165958.19274-3-narmstrong@baylibre.com
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
This is the 5.2.47 stable release
|
|
commit e6064cf4dafd75240ec7f512abfd5a63da9fce24 upstream.
This reverts commits 3d109bdca981 ("ARM: dts: sunxi: Remove useless
phy-names from EHCI and OHCI"), 0a3df8bb6dad ("ARM: dts: sunxi: h3/h5:
Remove useless phy-names from EHCI and OHCI") and 3c7ab90aaa28 ("arm64:
dts: allwinner: Remove useless phy-names from EHCI and OHCI").
It turns out that while the USB bindings were not mentionning it, the PHY
client bindings were mandating that phy-names is set when phys is. Let's
add it back.
Fixes: 3d109bdca981 ("ARM: dts: sunxi: Remove useless phy-names from EHCI and OHCI")
Fixes: 0a3df8bb6dad ("ARM: dts: sunxi: h3/h5: Remove useless phy-names from EHCI and OHCI")
Fixes: 3c7ab90aaa28 ("arm64: dts: allwinner: Remove useless phy-names from EHCI and OHCI")
Reported-by: Emmanuel Vadot <manu@bidouilliste.com>
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20191002112651.100504-1-mripard@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 0a930f64a1cc36a34797a9e54f3040ad1d5833f2 upstream.
Define "assigned-clocks" and "assigned-clock-rates" properties
for CAN[01] DT nodes, as required by the dt-bindings.
Fixes: eccc40002972c424 ("arm64: dts: renesas: r8a774a1: Add clkp2 clock to CAN nodes")
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Chris Paterson <Chris.Paterson2@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit e8efd2a8e20a9d7a7bd701950254a0ae04a8ce27 upstream.
Define "assigned-clocks" and "assigned-clock-rates" properties
for CAN[01] DT nodes, as required by the dt-bindings.
Fixes: 036bc85c1d06ef0a ("arm64: dts: renesas: r8a774c0: Add clkp2 clock to CAN nodes")
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Chris Paterson <Chris.Paterson2@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
This is the 5.2.44 stable release
|
|
commit 3b1f6c5e4dfaf767f6f2f120cd93b347b5a9f1aa upstream.
Fix the assigned-clock-parents to higher frequency clock to avoid h264
encode timeout:
[ 134.763465] mtk_vpu 10020000.vpu: vpu ipi 4 ack time out !
[ 134.769008] [MTK_VCODEC][ERROR][18]: vpu_enc_send_msg() vpu_ipi_send msg_id c002 len 32 fail -5
[ 134.777707] [MTK_VCODEC][ERROR][18]: vpu_enc_encode() AP_IPIMSG_ENC_ENCODE 0 fail
venc_sel is the clock used by h264 encoder, and venclt_sel is the clock
used by vp8 encoder. Assign venc_sel to vcodecpll_ck and venclt_sel to
vcodecpll_370p5.
vcodecpll 1482000000
vcodecpll_ck 494000000
venc_sel 494000000
...
vcodecpll_370p5 370500000
venclt_sel 370500000
Fixes: fbbad0287cec ("arm64: dts: Using standard CCF interface to set vcodec clk")
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Link: https://lore.kernel.org/r/20200504124442.208004-1-hsinyi@chromium.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit c604fd810bda667bdc20b2c041917baa7803e0fb upstream.
Dts files with Rockchip rk3399 'gpu' nodes were manually verified.
In order to automate this process arm,mali-midgard.txt
has been converted to yaml. In the new setup dtbs_check with
arm,mali-midgard.yaml expects interrupts and interrupt-names values
in the same order. Fix this for rk3399.
make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/gpu/
arm,mali-midgard.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200425143837.18706-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit c617ed88502d0b05149e7f32f3b3fd8a0663f7e2 upstream.
The status was removed of the '&gmac2phy' node with the apply
of a patch long time ago, so fix status for '&gmac2phy'
in 'rk3328-evb.dts'.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200425122345.12902-2-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit f4d71c6ea9e58c07dd4d02d09c5dd9bb780ec4b1 upstream.
Missing the renesas,ipmmu-main property on ipmmu_vip[01] nodes.
Fixes: 55697cbb44e4 ("arm64: dts: renesas: r8a779{65,80,90}: Add IPMMU devices nodes)
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/1587108543-23786-1-git-send-email-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 190c7f6fd43a776d4a6da1dac44408104649e9b7 upstream.
The device tree compiler complains that the dwc3 nodes have regs
properties but no matching unit addresses.
Add the unit addresses to the device node name. While at it, also rename
the nodes from "dwc3" to "usb", as guidelines require device nodes have
generic names.
Fixes: 7144224f2c2b ("arm64: dts: rockchip: support dwc3 USB for rk3399")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20200327030414.5903-7-wens@kernel.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 83b994129fb4c18a8460fd395864a28740e5e7fb upstream.
In some board device tree files, "rk805" was used for the RK805 PMIC's
node name. However the policy for device trees is that generic names
should be used.
Replace the "rk805" node name with the generic "pmic" name.
Fixes: 1e28037ec88e ("arm64: dts: rockchip: add rk805 node for rk3328-evb")
Fixes: 955bebde057e ("arm64: dts: rockchip: add rk3328-rock64 board")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20200327030414.5903-3-wens@kernel.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit e4f634d812634067b0c661af2e3cecfd629c89b8 upstream.
Use the correct dwc2 clock name.
Fixes: 9baf7d6be730 ("arm64: dts: meson: g12a: Add G12A USB nodes")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20200326160857.11929-3-narmstrong@baylibre.com
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
This is the 5.2.42 stable release
|
|
commit 46f94c7818e7ab82758fca74935ef3d454340b4e upstream.
If the mv88e6xxx DSA driver is built as a module, it causes the
ethernet driver to re-probe when it's loaded. This in turn causes
the gigabit PHY to be momentarily reset and reprogrammed. However,
we attempt to reprogram the PHY immediately after deasserting reset,
and the PHY ignores the writes.
This results in the PHY operating in the wrong mode, and the copper
link states down.
Set a reset deassert delay of 10ms for the gigabit PHY to avoid this.
Fixes: babc5544c293 ("arm64: dts: clearfog-gt-8k: 1G eth PHY reset signal")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 3e9a1a8b7f811de3eb1445d72f68766b704ad17c upstream.
Register range of display clocks is 0x10000, as it can be seen from
DE2 documentation.
Fix it.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Fixes: 2c796fc8f5dbd ("arm64: dts: allwinner: a64: add necessary device tree nodes for DE2 CCU")
[wens@csie.org: added fixes tag]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 5ea40f7106aaa4e2736d18075ca635389797fc16 upstream.
The DE2 bus takes two clocks, named bus and mod according to the binding.
However, the order of these clocks change from one SoC to another. Even
though it might not be an issue in most cases, having consistency will help
if we ever need to have some code to deal with deprecated bindings, and in
general it's just better.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit a81e5442d796ccfa2cc97d205a5477053264d978 upstream.
The TI sci-clk driver can scan the DT for all clocks provided by system
firmware and does this by checking the clocks property of all nodes, so
we must add this to the dwc3 nodes so USB clocks are available.
Without this USB does not work with latest system firmware i.e.
[ 1.714662] clk: couldn't get parent clock 0 for /interconnect@100000/dwc3@4020000
Fixes: cc54a99464ccd ("arm64: dts: ti: k3-am6: add USB suppor")
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Cc: stable@kernel.org
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit d79e9d7c1e4ba5f95f2ff3541880c40ea9722212 upstream.
The correct setting for the RGMII ports on LS1046ARDB is to
enable delay on both Rx and Tx so the interface mode used must
be PHY_INTERFACE_MODE_RGMII_ID.
Since commit 1b3047b5208a80 ("net: phy: realtek: add support for
configuring the RX delay on RTL8211F") the Realtek 8211F PHY driver
has control over the RGMII RX delay and it is disabling it for
RGMII_TXID. The LS1046ARDB uses two such PHYs in RGMII_ID mode but
in the device tree the mode was described as "rgmii".
Changing the phy-connection-type to "rgmii-id" to address the issue.
Fixes: 3fa395d2c48a ("arm64: dts: add LS1046A DPAA FMan nodes")
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 4022d808c45277693ea86478fab1f081ebf997e8 upstream.
The correct setting for the RGMII ports on LS1043ARDB is to
enable delay on both Rx and Tx so the interface mode used must
be PHY_INTERFACE_MODE_RGMII_ID.
Since commit 1b3047b5208a80 ("net: phy: realtek: add support for
configuring the RX delay on RTL8211F") the Realtek 8211F PHY driver
has control over the RGMII RX delay and it is disabling it for
RGMII_TXID. The LS1043ARDB uses two such PHYs in RGMII_ID mode but
in the device tree the mode was described as "rgmii_txid".
This issue was not apparent at the time as the PHY driver took the
same action for RGMII_TXID and RGMII_ID back then but it became
visible (RX no longer working) after the above patch.
Changing the phy-connection-type to "rgmii-id" to address the issue.
Fixes: bf02f2ffe59c ("arm64: dts: add LS1043A DPAA FMan support")
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
This is the 5.2.41 stable release
|
|
commit b54d3900862374e1bb2846e6b39d79c896c0b200 upstream.
The LS1043A SoC is affected by the A050385 erratum stating that
FMAN DMA read or writes under heavy traffic load may cause FMAN
internal resource leak thus stopping further packet processing.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 26c4b4758fce8f0ae744335e1762213be29db441 upstream.
There is only on Ethernet port and one Ethernet PHY on imx8qxp-mek.
Remove the unexisting ethphy1 port.
This fixes a run-time warning:
mdio_bus 5b040000.ethernet-1: MDIO device at address 1 is missing.
Fixes: fdea904e85e1 ("arm64: dts: imx: add imx8qxp mek support")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 8c867387160e89c9ffd12459f38e56844312a7a7 upstream.
Fix gmac compatible string to "altr,socfpga-stmmac-a10-s10". Gmac for
Agilex should use same compatible as Stratix 10.
Fixes: 4b36daf9ada3 ("arm64: dts: agilex: Add initial support for Intel's Agilex SoCFPGA")
Cc: stable@vger.kernel.org
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
This is the 5.2.40 stable release
|
|
commit 4c7eeb9af3e41ae7d840977119c58f3bbb3f4f59 upstream.
The commit 7aa9b9eb7d6a ("arm64: dts: allwinner: H6: Add PMU mode")
introduced support for the PMU found on the Allwinner H6. However, the
binding only allows for a single compatible, while the patch was adding
two.
Make sure we follow the binding.
Fixes: 7aa9b9eb7d6a ("arm64: dts: allwinner: H6: Add PMU mode")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 4ae7a3c3d7d31260f690d8d658f0365f3eca67a2 upstream.
The commit c35a516a4618 ("arm64: dts: allwinner: H5: Add PMU node")
introduced support for the PMU found on the Allwinner H5. However, the
binding only allows for a single compatible, while the patch was adding
two.
Make sure we follow the binding.
Fixes: c35a516a4618 ("arm64: dts: allwinner: H5: Add PMU node")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 7f2147350291569acd1df5a26dcdfc573916016f upstream.
An experimental test with the command below gives this error:
px30-evb.dt.yaml: dwmmc@ff390000: clock-names:2:
'ciu-drive' was expected
'ciu-drv' is not a valid dwmmc clock name,
so fix this by changing it to 'ciu-drive'.
make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200110161200.22755-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit d026c96b25b7ce5df89526aad2df988d553edb4d upstream.
QUSB2 PHY on msm8996 doesn't work well when autosuspend by
dwc3 core using USB2PHYCFG register is enabled. One of the
issue seen is that PHY driver reports PLL lock failure and
fails phy_init() if dwc3 core has USB2 PHY suspend enabled.
Fix this by using quirks to disable USB2 PHY LPM/suspend and
dwc3 core already takes care of explicitly suspending PHY
during suspend if quirks are specified.
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Signed-off-by: Paolo Pisati <p.pisati@gmail.com>
Link: https://lore.kernel.org/r/20191209151501.26993-1-p.pisati@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit c35a516a46187c8eeb7a56c64505ec6f7e22a0c7 upstream.
Add the Performance Monitoring Unit (PMU) device tree node to the H5
.dtsi, which tells DT users which interrupts are triggered by PMU
overflow events on each core.
As with the A64, the interrupt numbers from the manual were wrong (off
by 4), the actual SPI IDs have been gathered in U-Boot, and were
verified with perf in Linux.
Tested with perf record and taskset on an OrangePi PC2.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 7aa9b9eb7d6a8fde7acbe0446444f7e3fae1fe3b upstream.
Add the Performance Monitoring Unit (PMU) device tree node to the H6
.dtsi, which tells DT users which interrupts are triggered by PMU
overflow events on each core. The numbers come from the manual and have
been checked in U-Boot and with perf in Linux.
Tested with perf record and taskset on a Pine H64.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
Bruce Ashfield
Ricardo Cañuelo
Alim Akhtar
Stephan Gerhold
Heiko Stuebner
Neil Armstrong
Jerome Brunet
Jon Hunter
Loic Poulain
Amit Kucheria
Hsin-Yi Wang
Andre Przywara
Maxime Ripard
Fabrizio Castro
Johan Jonker
Yoshihiro Shimoda
Chen-Yu Tsai
Russell King
Jernej Skrabec
Maxime Ripard
Dave Gerlach
Madalin Bucur
Madalin Bucur
Fabio Estevam
Ley Foon Tan
Maxime Ripard
Manu Gautam