| Age | Commit message (Collapse) | Author |
|---|
|
A long running stress test on a custom board shipping an AXG SoCs and a
Realtek RTL8211F PHY revealed that after a few hours the connection
speed would drop drastically, from ~1000Mbps to ~3Mbps. At the same time
the 'macirq' (eth0) IRQ would stop being triggered at all and as
consequence the GMAC IRQs never ACKed.
After a painful investigation the problem seemed to be due to a wrong
defined IRQ type for the GMAC IRQ that should be LEVEL_HIGH instead of
EDGE_RISING.
The change in the macirq IRQ type also solved another long standing
issue affecting this SoC/PHY where EEE was causing the network
connection to die after stressing it with iperf3 (even though much
sooner). It's now possible to remove the 'eee-broken-1000t' quirk as
well.
Fixes: feb3cbea0946 ("ARM64: dts: meson-gxbb-odroidc2: fix GbE tx link breakage")
Fixes: 6d28d577510f ("ARM64: dts: meson-axg: fix ethernet stability issue")
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Enable the GPIO interrupt controller for the AXG SoCs.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Now that the GPIO controller has been enabled also on AXG we can hook up
the GPIO interrupt for the PHY.
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Add the clock inputs of the clock controllers
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
There is actually no alternate xtal on any of the axg board I have
seen so far. The 32k is actually generated internally, deriving from
the 24MHz main xtal.
Amlogic SoC also have the option to provide the 32k reference externally,
through one of the AO pads, but no platform is using this ATM.
Fixes: 5e395e146667 ("ARM64: dts: meson-axg: add an 32K alt aoclk")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Add the watchdog node also on the AXG platforms.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
The Amlogic Meson GX SoCs embeds a clock measurer IP to measure the internal
clock paths frequencies.
This patch adds the node in the top-level meson-gx dtsi.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Each CPU can (and does) participate in cooling down the system but the
DT only captures a handful of them, normally CPU0, in the cooling maps.
Things work by chance currently as under normal circumstances its the
first CPU of each cluster which is used by the operating systems to
probe the cooling devices. But as soon as this CPU ordering changes and
any other CPU is used to bring up the cooling device, we will start
seeing failures.
Also the DT is rather incomplete when we list only one CPU in the
cooling maps, as the hardware doesn't have any such limitations.
Update cooling maps to include all devices affected by individual trip
points.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Add Libretech aml-s805x-ac board (aka 'La Frite') support
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
This patch adds support for the Phicomm N1. This device based on P230 reference design.
And this box doesn't have cvbs, so disable related section in device tree.
Signed-off-by: He Yangxuan <yangxuan8282@gmail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
On Amlogic chipsets, the bias set through pinconf applies to the pad
itself, not only the GPIO function. This means that even when we change
the function of the pad from GPIO to anything else, the bias previously
set still applies.
As we have seen with the eMMC, depending on the bias type and the function,
it may trigger problems.
The underlying issue is that we inherit whatever was left by previous user
of the pad (pinconf, u-boot or the ROM code). As a consequence, the actual
setup we will get is undefined.
There is nothing mentioned in the documentation about pad bias and pinmux
function, however leaving it undefined is not an option.
This change consistently disable the pad bias for every pinmux functions.
It seems to work well, we can only assume that the necessary bias (if any)
is already provided by the pin function itself.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
In some cases (such as a boot from SPI) the bootloader or the ROM code may
leave a bias pull-down on the mmc pins. If so the MMC will fail during the
initialisation.
Explicitly disabling the pinmux solves the problem.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
In the pinmux of the mmc clk_gate nodes, we define 2 subnodes. One for
the function definition, the other for the bias. This is not necessary
since we can define the function and the bias in the same subnode.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Add broadcom bluetooth device on the s400
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
This patch disable EEE advertisement for P230 board (DWMAC + RTL8211F).
If not disable it, the network connection is not stable, will got issues
like throughput drop or broken link.
Signed-off-by: He Yangxuan <yangxuan8282@gmail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Enable SCPI on the axg platform, with cpu clock and hwmon
(core temperature) support
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Correct the unit-address in the node name of the SRAM shared memory
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
MHU mailbox address is wrong. Fixing it enables the mailboxes on the A113.
These mailboxes are needed for SCPI
Fixes: 9d59b708500f ("arm64: dts: meson-axg: add initial A113D SoC DT support")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
The hdmi_5v regulator must be enabled to provide power to the physical HDMI
PHY and enables the HDMI 5V presence loopback for the monitor.
Fixes: b409f625a6d5 ("ARM64: dts: meson-gx: Add HDMI_5V regulator on selected boards")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Add the secure monitor device to the axg platform.
With this, we can read the SoC serial number.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
The uart used with bluetooth chipset on the s400 has flow control
available. Let's enable it.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
The gpio line names were set in the pinctrl node instead of the gpio node,
at the time it was merged, it worked, but was obviously wrong.
This patch moves the properties to the gpio nodes.
Fixes: 60795933b709 ("ARM64: dts: meson-gxl-khadas-vim: Add GPIO lines names")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
The gpio line names were set in the pinctrl node instead of the gpio node,
at the time it was merged, it worked, but was obviously wrong.
This patch moves the properties to the gpio nodes.
Fixes: b03c7d6438bb ("ARM64: dts: meson-gxbb-odroidc2: Add GPIO lines names")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
The gpio line names were set in the pinctrl node instead of the gpio node,
at the time it was merged, it worked, but was obviously wrong.
This patch moves the properties to the gpio nodes.
Fixes: 12ada0513d7a ("ARM64: dts: meson-gxbb-nanopi-k2: Add GPIO lines names")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
The gpio line names were set in the pinctrl node instead of the gpio node,
at the time it was merged, it worked, but was obviously wrong.
This patch moves the properties to the gpio nodes.
Fixes: 47884c5c746e ("ARM64: dts: meson-gxl-libretech-cc: Add GPIO lines names")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
section 2.2.1 of the DT specs says: " If the node has no reg property,
the @unit-address must be omitted and the node-name alone differentiates
the node from other nodes at the same level in the tree"
Simply replace the '@' with a '-' to fix this warning.
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
This enables Bluetooth support for the following models:
- Khadas VIM basic (AP6212) using firmware BCM43438A1.hcd
- Khadas VIM pro (AP6255) using firmware BCM4345C0.hcd
The AP6212 module used on the VIM basic has an ID clash with another
device. To get Bluetooth working you either need to apply a kernel
patch to drivers/bluetooth/btbcm.c so 0x2209 loads BCM43438A1 or the
BCM43438A1.hcd firmware must be renamed to BCM43430A1.hcd.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Add the required peripheral clock for the efuse device.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
While it is possible to rework the s400 board to solder an eMMC on it,
it is not the default option and most boards are fitted with a NAND
instead.
Let's disable the emmc device by default to reflect this. The board
equipped with an eMMC will just have to alter the DT in the
bootloader, like we do for the reserved memory regions.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
eMMC pwrseq is defined in the s400 dts but not used in the emmc node.
This is probably just a copy/paste error
Fixes: 221cf34bac54 ("ARM64: dts: meson-axg: enable the eMMC controller")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Try to add basic DT support for the Amlogic's Meson-G12A S905D2 SoC,
which describe components as follows: Reserve Memory, CPU, GIC, IRQ,
Timer, UART. It's capable of booting up into the serial console.
Signed-off-by: Jianxin Pan <jianxin.pan@amlogic.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
dtc has new checks for SPI buses. The meson dts files have a node named
spi' which causes false positive warnings. As the node is a pinctrl child
node, change the node name to be 'spi-pins' to fix the warnings.
arch/arm64/boot/dts/amlogic/meson-gxbb-nanopi-k2.dtb: Warning (spi_bus_bridge): /soc/periphs@c8834000/pinctrl@4b0/spi: incorrect #address-cells for SPI bus
Cc: Carlo Caione <carlo@caione.org>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: linux-amlogic@lists.infradead.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
The order between "syscon" and "simple-mfd" is important because in these
particular cases, the node needs to be first a "simple-mfd" to expose
it's sub-nodes, and later on a "syscon" to permit other nodes to access
this register space through the "syscon" mechanism.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Add missing chosen and memory nodes.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Use the correct compatible for the AXG ethernet mac node.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Enable the PDM input device on the S400 and it to the sound card
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
There are 7 digital mics on the MIC daughter board attached
to the s400 board, so add the digital microphone codec to
its DTS
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Add the PDM device of the axg audio subsystem
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
DMC is a small memory region with various registers,
including the ones needed for the canvas module.
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
There is actually several different libretech board with the CC suffix
so the model name is not appropriate here. Update to something more
specific
Reported-by: Da Xue <da@lessconfused.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Devices using the new V4L2 mem2mem vdec require a larger CMA pool. As
nearly all GX* devices are video/media focused and will use it, set a
larger (256MB) default value.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Sort DT nodes by address when possible, by node node name otherwise.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Add the sound card of the s400. With it the following interface
should be working:
* Lineout
* Daugther card speaker 1 (same output as lineout)
* Linein
* SPDIF output
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Enable the audio devices on the s400.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Add TODDR and FRDDR audio fifos of the AXG SoC.
These fifos are the capture and playback memory interfaces of audio
subsystem of the AXG.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into next/dt
Amlogic 64-bit DT updates for v4.19, round 3
- add DT support for AXG Audio
* tag 'amlogic-dt64-3' of https://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
arm64: dts: meson-axg: add spdif-dit codec
arm64: dts: meson-axg: add lineout codec
arm64: dts: meson-axg: add linein codec
arm64: dts: meson-axg: add tdm interfaces
arm64: dts: meson-axg: add tdmout formatters
arm64: dts: meson-axg: add tdmin formatters
arm64: dts: meson-axg: add spdifout
arm64: dts: meson-axg: add audio arb reset controller
arm64: dts: meson-axg: add usb power regulator
arm64: dts: meson-axg: add vcc 5v regulator on the s400
arm64: dts: meson-axg: improve power supplies description
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into next/dt
Amlogic 64-bit DT changes for v4.19, round 2
- new SoC: S905W
- new boards: based on S905W: Amlogic P281, Oranth Tanix TX3 Mini
- AXG: add DT for new audio clock controller
* tag 'amlogic-dt64-2-1' of https://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
ARM64: dts: meson-gxl: add support for the Oranth Tanix TX3 Mini
ARM64: dts: meson-gxl: add support for the S905W SoC and the P281 board
dt-bindings: arm: amlogic: Add support for the Oranth Tanix TX3 Mini
dt-bindings: arm: amlogic: Add support for GXL S905W and the P281 board
dt-bindings: add vendor prefix for Shenzhen Oranth Technology Co., Ltd.
ARM64: dts: meson-axg: add the audio clock controller
clk: meson: expose GEN_CLK clkid
clk: meson-axg: add pcie and mipi clock bindings
dt-bindings: clock: add meson axg audio clock controller bindings
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Add the SPDIF playback codec to the axg s400 board
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Add the es7154 digital to analog converter which supplies the
lienout jack of the s400
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Add the es7241 analog to digital converter which is fed by the
lienin jack of the s400
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
Carlo Caione
Jerome Brunet
Neil Armstrong
Viresh Kumar
He Yangxuan
Christian Hewitt
Jianxin Pan
Rob Herring
Maxime Jourdan
Olof Johansson