| Age | Commit message (Collapse) | Author |
|---|
|
commit a1af7f36c70369b971ee1cf679dd68368dad23f0 upstream.
Remove non-removable and mmc-ddr-1_8v properties from the sdmmc0
node which come probably from an unchecked copy/paste.
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Fixes:42ed535595ec "ARM: dts: at91: introduce the sama5d2 ptc ek board"
Cc: stable@vger.kernel.org # 4.19 and later
Link: https://lore.kernel.org/r/20200401221504.41196-1-ludovic.desroches@microchip.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit be0ec060b54f0481fb95d59086c1484a949c903c ]
These error messages are output when booting on a BCM HR2 system:
GIC: PPI11 is secure or misconfigured
GIC: PPI13 is secure or misconfigured
Per ARM documentation these interrupts are triggered on a rising edge.
See ARM Cortex A-9 MPCore Technical Reference Manual, Revision r4p1,
Section 3.3.8 Interrupt Configuration Registers.
The same issue was resolved for NSP systems in commit 5f1aa51c7a1e
("ARM: dts: NSP: Fix PPI interrupt types").
Fixes: b9099ec754b5 ("ARM: dts: Add Broadcom Hurricane 2 DTS include file")
Signed-off-by: Hamish Martin <hamish.martin@alliedtelesis.co.nz>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 58bb90ab415562eededb932455046924e65df342 ]
The status "ACT" led on the Raspberry Pi Zero W is on when GPIO 47 is low.
This has been verified on a board and somewhat confirmed by both the GPIO
name ("STATUS_LED_N") and the reduced schematics [1].
[1]: https://www.raspberrypi.org/documentation/hardware/raspberrypi/schematics/rpi_SCH_ZeroW_1p1_reduced.pdf
Fixes: 2c7c040c73e9 ("ARM: dts: bcm2835: Add Raspberry Pi Zero W")
Signed-off-by: Vincent Stehlé <vincent.stehle@laposte.net>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 665e7c73a7724a393b4ec92d1ae1e029925ef2b7 ]
Avoid LDB and IPU DI clocks both using the same parent. LDB requires
pasthrough clock to avoid breaking timing while IPU DI does not.
Force IPU DI clocks to use IMX6QDL_CLK_PLL2_PFD0_352M as parent
and LDB to use IMX6QDL_CLK_PLL5_VIDEO_DIV.
This fixes an issue where attempting atomic modeset while using
HDMI and display port at the same time causes LDB clock programming
to destroy the programming of HDMI that was done during the same
modeset.
Cc: stable@vger.kernel.org
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
[Use IMX6QDL_CLK_PLL2_PFD0_352M instead of IMX6QDL_CLK_PLL2_PFD2_396M
originally chosen by Robert Beckett to avoid affecting eMMC clock
by DRM atomic updates]
Signed-off-by: Ian Ray <ian.ray@ge.com>
[Squash Robert's and Ian's commits for bisectability, update patch
description and add stable tag]
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2c962369d72f286659e6446919f88d69b943cb4d ]
The size field of the tag header structure is supposed to be set to the
size of a tag structure including the header.
Fixes: c772568788b5f0 ("ARM: add additional table to compressed kernel")
Signed-off-by: Łukasz Stelmach <l.stelmach@samsung.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 855bdca1781c79eb661f89c8944c4a719ce720e8 ]
A test with the command below gives these errors:
arch/arm/boot/dts/rk3229-evb.dt.yaml: spi-0:
'#address-cells' is a required property
arch/arm/boot/dts/rk3229-evb.dt.yaml: spi-1:
'#address-cells' is a required property
arch/arm/boot/dts/rk3229-xms6.dt.yaml: spi-0:
'#address-cells' is a required property
arch/arm/boot/dts/rk3229-xms6.dt.yaml: spi-1:
'#address-cells' is a required property
The $nodename pattern for spi nodes is
"^spi(@.*|-[0-9a-f])*$". To prevent warnings rename
'spi-0' and 'spi-1' pinctrl sub nodenames to
'spi0' and 'spi1' in 'rk322x.dtsi'.
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/spi/spi-controller.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200424123923.8192-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b14f3898d2c25a9b47a61fb879d0b1f3af92c59b ]
Dts files with Rockchip 'gpu' nodes were manually verified.
In order to automate this process arm,mali-utgard.txt
has been converted to yaml. In the new setup dtbs_check with
arm,mali-utgard.yaml expects clock-names values
in the same order, so fix that.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200425192500.1808-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 621c8d0c233e260232278a4cfd3380caa3c1da29 ]
A test with the command below gives for example this error:
arch/arm/boot/dts/rk3229-xms6.dt.yaml: phy@0:
'#phy-cells' is a required property
The phy nodename is normally used by a phy-handle.
This node is however compatible with
"ethernet-phy-id1234.d400", "ethernet-phy-ieee802.3-c22"
which is just been added to 'ethernet-phy.yaml'.
So change nodename to 'ethernet-phy' for which '#phy-cells'
is not a required property
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=~/.local/lib/python3.5/site-packages/dtschema/schemas/
phy/phy-provider.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20200416170321.4216-2-jbx6244@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 287e0d538fcec2f6e8eb1e565bf0749f3b90186d ]
A test with the command below gives for example this error:
arch/arm/boot/dts/rk3228-evb.dt.yaml: phy@0:
'#phy-cells' is a required property
The phy nodename is normally used by a phy-handle.
This node is however compatible with
"ethernet-phy-id1234.d400", "ethernet-phy-ieee802.3-c22"
which is just been added to 'ethernet-phy.yaml'.
So change nodename to 'ethernet-phy' for which '#phy-cells'
is not a required property
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=~/.local/lib/python3.5/site-packages/dtschema/schemas/
phy/phy-provider.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20200416170321.4216-1-jbx6244@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit e47cb97f153193d4b41ca8d48127da14513d54c7 upstream.
The Clock Pulse Generator (CPG) device node lacks the extal2 clock.
This may lead to a failure registering the "r" clock, or to a wrong
parent for the "usb24s" clock, depending on MD_CK2 pin configuration and
boot loader CPG_USBCKCR register configuration.
This went unnoticed, as this does not affect the single upstream board
configuration, which relies on the first clock input only.
Fixes: d9ffd583bf345e2e ("ARM: shmobile: r8a7740: add SoC clocks to DTS")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Link: https://lore.kernel.org/r/20200508095918.6061-1-geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0f739fdfe9e5ce668bd6d3210f310df282321837 upstream.
The R-Mobile APE6 Compare Match Timer 1 generates 8 interrupts, one for
each channel, but currently only 1 is described.
Fix this by adding the missing interrupts.
Fixes: f7b65230019b9dac ("ARM: shmobile: r8a73a4: Add CMT1 node")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200408090926.25201-1-geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit cbe63a8358310244e6007398bd2c7c70c7fd51cd upstream.
The Y Soft yapp4 platform supports up to two Ethernet ports.
The Ursa board though has only one Ethernet port populated and that is
the port@2. Since the introduction of this platform into mainline a wrong
port was deleted and the Ethernet could never work. Fix this by deleting
the correct port node.
Fixes: 87489ec3a77f ("ARM: dts: imx: Add Y Soft IOTA Draco, Hydra and Ursa boards")
Cc: stable@vger.kernel.org
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0caf34350a25907515d929a9c77b9b206aac6d1e upstream.
The I2C2 pins are already used and the following errors are seen:
imx27-pinctrl 10015000.iomuxc: pin MX27_PAD_I2C2_SDA already requested by 10012000.i2c; cannot claim for 1001d000.i2c
imx27-pinctrl 10015000.iomuxc: pin-69 (1001d000.i2c) status -22
imx27-pinctrl 10015000.iomuxc: could not request pin 69 (MX27_PAD_I2C2_SDA) from group i2c2grp on device 10015000.iomuxc
imx-i2c 1001d000.i2c: Error applying setting, reverse things back
imx-i2c: probe of 1001d000.i2c failed with error -22
Fix it by adding the correct I2C1 IOMUX entries for the pinctrl_i2c1 group.
Cc: <stable@vger.kernel.org>
Fixes: 61664d0b432a ("ARM: dts: imx27 phyCARD-S pinctrl")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 90d4d3f4ea45370d482fa609dbae4d2281b4074f upstream.
Even though commit cfb5d65f2595 ("ARM: dts: dra7: Add bus_dma_limit
for L3 bus") added bus_dma_limit for L3 bus, the PCIe controller
gets incorrect value of bus_dma_limit.
Fix it by adding empty dma-ranges property to axi@0 and axi@1
(parent device tree node of PCIe controller).
Cc: stable@kernel.org
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b7dc7205b2ae6b6c9d9cfc3e47d6f08da8647b10 upstream.
We need to indicate that powering off the TI WiFi is safe, to avoid:
wl18xx_driver wl18xx.2.auto: Unbalanced pm_runtime_enable!
wl1271_sdio mmc0:0001:2: wl12xx_sdio_power_on: failed to get_sync(-13)
which prevents the WiFi being functional.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Cc: Miguel Borges de Freitas <miguelborgesdefreitas@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 90444b958461a5f8fc299ece0fe17eab15cba1e1 upstream.
Since its inception the module was meant to be disabled by default, but
the original commit failed to add the relevant property.
Fixes: 4aba4cf82054 ("ARM: dts: bcm2835: Add the DSI module nodes and clocks")
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit da180322582bd9db07f29e6d4a2d170afde0703f upstream.
As it can be seen from DE2 manual, clock range is 0x10000.
Fix it.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Fixes: 73f122c82775 ("ARM: dts: sun8i: a83t: Add display pipeline")
Fixes: 05a43a262d03 ("ARM: dts: sun8i: r40: Add HDMI pipeline")
Fixes: 21b299209330 ("ARM: sun8i: v3s: add device nodes for DE2 display pipeline")
Fixes: d8c6f1f0295c ("ARM: sun8i: h3/h5: add DE2 CCU device node for H3")
[wens@csie.org: added fixes tags]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 1a7e99599dffd836fcb720cdc0eaf3cd43d7af4a ]
A test with the command below gives this error:
arch/arm/boot/dts/rk3188-bqedison2qc.dt.yaml: lvds-encoder:
'ports' is a required property
Fix error by adding a ports wrapper for port@0 and port@1
inside the 'lvds-encoder' node for rk3188-bqedison2qc.
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/display/
bridge/lvds-codec.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200316174647.5598-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9cd568dc588c5d168615bf34f325fabe33b2c9a0 ]
A test with the command below does not detect all errors
in combination with 'additionalProperties: false' and
allOf:
- $ref: "synopsys-dw-mshc-common.yaml#"
allOf:
- $ref: "mmc-controller.yaml#"
'additionalProperties' applies to all properties that are not
accounted-for by 'properties' or 'patternProperties' in
the immediate schema.
First when we combine rockchip-dw-mshc.yaml,
synopsys-dw-mshc-common.yaml and mmc-controller.yaml it gives
this error:
arch/arm/boot/dts/rk3188-bqedison2qc.dt.yaml: mmc@10218000:
'vmmcq-supply' does not match any of the regexes:
'^.*@[0-9]+$',
'^clk-phase-(legacy|sd-hs|mmc-(hs|hs[24]00|ddr52)|
uhs-(sdr(12|25|50|104)|ddr50))$',
'pinctrl-[0-9]+'
'vmmcq-supply' is not a valid property name for mmc nodes.
Fix this error by renaming it to 'vqmmc-supply'.
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200307134841.13803-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 4141f1a40fc0789f6fd4330e171e1edf155426aa upstream.
In order to wake from suspend by ethernet magic packets the GPC
must be used as intc does not have wakeup functionality.
But the FEC DT node currently uses interrupt-extended,
specificying intc, thus breaking WoL.
This problem is probably fallout from the stacked domain conversion
as intc used to chain to GPC.
So replace "interrupts-extended" by "interrupts" to use the default
parent which is GPC.
Fixes: b923ff6af0d5 ("ARM: imx6: convert GPC to stacked domains")
Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7007f2eca0f258710899ca486da00546d03db0ed upstream.
USB_C_DET pin shouldn't be in ethernet group.
Creating a separate group allows one to use this pin
as an USB ID pin.
Fixes: b326629f25b7 ("ARM: dts: imx7: add Toradex Colibri iMX7S/iMX7D suppor")
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 32a1671ff8e84f0dfff3a50d4b2091d25e91f5e2 upstream.
Recent changes in the SPI core and the SPI-GPIO driver revealed that the
GPIO lines for the LD9040 LCD controller on the UniversalC210 board are
defined incorrectly. Fix the polarity for those lines to match the old
behavior and hardware requirements to fix LCD panel operation with
recent kernels.
Cc: <stable@vger.kernel.org> # 5.0.x
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit b46b2b7ba6e104d265ab705914859ec0db7a98c5 ]
Commit cd28d1d6e52e ("net: phy: at803x: Disable phy delay for RGMII mode")
caused a regression for dm814x boards where NFSroot would no longer work.
Let's fix the issue by configuring "rgmii-id" mode as internal delays are
needed that is no longer the case with "rgmii" mode.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit a40550952c000667b20082d58077bc647da6c890 ]
Lowering the voltage solves the quick image degradation over time
(minutes), that was probably caused by overheating.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit fe3a04824f75786e39ed74e82fb6cb2534c95fe4 upstream.
When the AHCI device node was added, it was added in the wrong location
in the device tree file. The device nodes should be sorted by register
address.
Move the device node to before EHCI1, where it belongs.
Fixes: 41c64d3318aa ("ARM: dts: sun8i: r40: add sata node")
Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0c5220a3c1242c7a2451570ed5f5af69620aac75 upstream.
Commit a758f50f10cf ("mtd: onenand: omap2: Configure driver from DT")
started using DT specified timings for GPMC, and as a result the
OneNAND stopped working on N900 as we had wrong values in the DT.
Fix by updating the values to bootloader timings that have been tested
to be working on Nokia N900 with OneNAND manufacturers: Samsung,
Numonyx.
Fixes: a758f50f10cf ("mtd: onenand: omap2: Configure driver from DT")
Signed-off-by: Arthur Demchenkov <spinal.by@gmail.com>
Tested-by: Merlijn Wajer <merlijn@wizzup.org>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 636b45b8efa91db05553840b6c0120d6fa6b94fa upstream.
The current set minimum voltage of 730000µV seems to be wrong. I don't
know the document which specifies that but the imx6qdl datasheets says
that the minimum voltage should be 0.925V for VDD_ARM (LDO bypassed,
lowest opp) and 1.15V for VDD_SOC (LDO bypassed, lowest opp).
Fixes: ddec5d1c0047 ("ARM: dts: imx6: Add initial support for phyCORE-i.MX 6 SOM")
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6687c201fdc3139315c2ea7ef96c157672805cdc upstream.
Define the sdhci pinctrl state as "default" so it gets applied
correctly and to match all other RPis.
Fixes: 2c7c040c73e9 ("ARM: dts: bcm2835: Add Raspberry Pi Zero W")
Signed-off-by: Nick Hudson <skrll@netbsd.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit deeabb4c1341a12bf8b599e6a2f4cfa4fd74738c upstream.
Disable all rps-irq interrupts during driver initialization to prevent
an accidental interrupt on GIC.
Fixes: 84316f4ef141 ("ARM: boot: dts: Add Oxford Semiconductor OX810SE dtsi")
Fixes: 38d4a53733f5 ("ARM: dts: Add support for OX820 and Pogoplug V3")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b642d4825441bf30c72b72deb739bd2d5f53af08 upstream.
USB-ID signal has a pullup on the schematic, but in reality it's not
pulled up, so add a GPIO pullup. And we also need a usb0_vbus_power-supply
for VBUS detection.
This fixes OTG mode detection and charging issues on TBS A711 tablet.
The issues came from ID pin reading 0, causing host mode to be enabled,
when it should not be, leading to DRVVBUS being enabled, which disabled
the charger.
Fixes: f2f221c7810b824e ("ARM: dts: sun8i: a711: Enable USB OTG")
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit dfa7ea303f56a3a8b1ed3b91ef35af2da67ca4ee upstream.
The L3 interconnect's memory map is from 0x0 to
0xffffffff. Out of this, System memory (SDRAM) can be
accessed from 0x80000000 to 0xffffffff (2GB)
OMAP5 does support 4GB of SDRAM but upper 2GB can only be
accessed by the MPU subsystem.
Add the dma-ranges property to reflect the physical address limit
of the L3 bus.
Cc: stable@kernel.org
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit cfb5d65f25959f724081bae8445a0241db606af6 upstream.
The L3 interconnect's memory map is from 0x0 to
0xffffffff. Out of this, System memory (SDRAM) can be
accessed from 0x80000000 to 0xffffffff (2GB)
DRA7 does support 4GB of SDRAM but upper 2GB can only be
accessed by the MPU subsystem.
Add the dma-ranges property to reflect the physical address limit
of the L3 bus.
Issues ere observed only with SATA on DRA7-EVM with 4GB RAM
and CONFIG_ARM_LPAE enabled. This is because the controller
supports 64-bit DMA and its driver sets the dma_mask to 64-bit
thus resulting in DMA accesses beyond L3 limit of 2G.
Setting the correct bus_dma_limit fixes the issue.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Cc: stable@kernel.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 27f13774654ea6bd0b6fc9b97cce8d19e5735661 ]
'dma-ranges' in a PCI bridge node does correctly set dma masks for PCI
devices not described in the DT. Certain DRA7 platforms (e.g., DRA76)
has RAM above 32-bit boundary (accessible with LPAE config) though the
PCIe bridge will be able to access only 32-bits. Add 'dma-ranges'
property in PCIe RC DT nodes to indicate the host bridge can access
only 32 bits.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 00a39c92c8ab94727f021297d1748531af113fcd ]
DMTimers 13 - 16 are PWM capable and also can be used for CPTS input
signals generation. Hence, mark them as "ti,timer-pwm".
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 89604523a76eb3e13014b2bdab7f8870becee284 upstream.
When using plugins, GCC requires that the -fplugin= options precedes
any of its plugin arguments appearing on the command line as well.
This is usually not a concern, but as it turns out, this requirement
is causing some issues with ARM's per-task stack protector plugin
and Kbuild's implementation of $(cc-option).
When the per-task stack protector plugin is enabled, and we tweak
the implementation of cc-option not to pipe the stderr output of
GCC to /dev/null, the following output is generated when GCC is
executed in the context of cc-option:
cc1: error: plugin arm_ssp_per_task_plugin should be specified before \
-fplugin-arg-arm_ssp_per_task_plugin-tso=1 in the command line
cc1: error: plugin arm_ssp_per_task_plugin should be specified before \
-fplugin-arg-arm_ssp_per_task_plugin-offset=24 in the command line
These errors will cause any option passed to cc-option to be treated
as unsupported, which is obviously incorrect.
The cause of this issue is the fact that the -fplugin= argument is
added to GCC_PLUGINS_CFLAGS, whereas the arguments above are added
to KBUILD_CFLAGS, and the contents of the former get filtered out of
the latter before being passed to the GCC running the cc-option test,
and so the -fplugin= option does not appear at all on the GCC command
line.
Adding the arguments to GCC_PLUGINS_CFLAGS instead of KBUILD_CFLAGS
would be the correct approach here, if it weren't for the fact that we
are using $(eval) to defer the moment that they are added until after
asm-offsets.h is generated, which is after the point where the contents
of GCC_PLUGINS_CFLAGS are added to KBUILD_CFLAGS. So instead, we have
to add our plugin arguments to both.
For similar reasons, we cannot append DISABLE_ARM_SSP_PER_TASK_PLUGIN
to KBUILD_CFLAGS, as it will be passed to GCC when executing in the
context of cc-option, whereas the other plugin arguments will have
been filtered out, resulting in a similar error and false negative
result as above. So add it to ccflags-y instead.
Fixes: 189af4657186da08 ("ARM: smp: add support for per-task stack canaries")
Reported-by: Merlijn Wajer <merlijn@wizzup.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Acked-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2773fe1d31c42ffae2a9cb9a6055d99dd86e2fee upstream.
SD/MMC on Colibri iMX7S/D modules successfully support
200Mhz frequency in HS200 mode.
Removing the unnecessary max-frequency limit significantly
increases the performance:
== before fix ====
root@colibri-imx7-emmc:~# hdparm -t /dev/mmcblk0
/dev/mmcblk0:
Timing buffered disk reads: 252 MB in 3.02 seconds = 83.54 MB/sec
==================
=== after fix ====
root@colibri-imx7-emmc:~# hdparm -t /dev/mmcblk0
/dev/mmcblk0:
Timing buffered disk reads: 408 MB in 3.00 seconds = 135.94 MB/sec
==================
Fixes: f928a4a377e4 ("ARM: dts: imx7: add Toradex Colibri iMX7D 1GB (eMMC) support")
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 78722d37b2b4cf9178295e2aa5510880e6135fd7 upstream.
The IPU1 functional clock is the output of a mux clock (represented
by ipu1_gfclk_mux previously) and the clock source for this has been
updated to be sourced from dpll_core_h22x2_ck in commit 39879c7d963e
("ARM: dts: dra7xx-clocks: Source IPU1 functional clock from CORE DPLL").
ipu1_gfclk_mux is an obsolete clock now with the clkctrl conversion,
and this clock source parenting is lost during the new clkctrl layout
conversion.
Remove this stale clock and fix up the clock source for this mux
clock using the latest equivalent clkctrl clock. This restores the
previous logic and ensures that the IPU1 continues to run at the
same frequency of IPU2 and independent of the ABE DPLL.
Fixes: b5f8ffbb6fad ("ARM: dts: dra7: convert to use new clkctrl layout")
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 31623468be0bf57617b8057dcd335693935a9491 upstream.
The commit 337c6c9a69af ("ARM: dts: am437x-idk-evm: Disable
OPP50 for MPU") adjusts couple of OPP nodes defined in the
common am4372.dtsi file, but used outdated node names. This
results in these getting treated as new OPP nodes with missing
properties.
Fix this properly by using the correct node names as updated in
commit b9cb2ba71848 ("ARM: dts: Use - instead of @ for DT OPP
entries for TI SoCs").
Reported-by: Roger Quadros <rogerq@ti.com>
Fixes: 337c6c9a69af ("ARM: dts: am437x-idk-evm: Disable OPP50 for MPU")
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit eb0bbba7636b9fc81939d6087a5fe575e150c95a upstream.
Currently the vmmc is supplied by the 1.8V pmic rail but this is wrong.
The default module behaviour is to power VCCQ and VCC by the 3.3V power
rail. Optional the user can connect the VCCQ to the pmic 1.8V emmc
power rail using a solder jumper.
Fixes: ddec5d1c0047 ("ARM: dts: imx6: Add initial support for phyCORE-i.MX 6 SOM")
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7155c44624d061692b4c13aa8343f119c67d4fc0 upstream.
The difference between "fsl,etsec2-mdio" and "gianfar" has to do with
the .get_tbipa function, which calculates the address of the TBIPA
register automatically, if not explicitly specified. [ see
drivers/net/ethernet/freescale/fsl_pq_mdio.c ]. On LS1021A, the TBIPA
register is at offset 0x30 within the port register block, which is what
the "gianfar" method of calculating addresses actually does.
Luckily, the bad "compatible" is inconsequential for ls1021a.dtsi,
because the TBIPA register is explicitly specified via the second "reg"
(<0x0 0x2d10030 0x0 0x4>), so the "get_tbipa" function is dead code.
Nonetheless it's good to restore it to its correct value.
Background discussion:
https://www.spinics.net/lists/stable/msg361156.html
Fixes: c7861adbe37f ("ARM: dts: ls1021: Fix SGMII PCS link remaining down after PHY disconnect")
Reported-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit fa63c0039787b8fbacf4d6a51e3ff44288f5b90b upstream.
dra76x is not affected by i887 which requires mmc3 node to be limited to
a max frequency of 64 MHz. Fix this by overwriting the correct value in
the the dra76 specific dtsi.
Fixes: 895bd4b3e5ec ("ARM: dts: Add support for dra76-evm")
Cc: stable@vger.kernel.org
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit f24667779b5348279e5e4328312a141a730a1fc7 ]
frame-inversion is "flag" not "uint32".
This patch fixup it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit cf206bca178cd5b5a436494b2e0cea75295944f4 ]
An experimental test with the command below gives this error:
rk3188-bqedison2qc.dt.yaml: dwmmc@10218000: wifi@1:
'reg' is a required property
So fix this by adding a reg property to the brcmf sub node.
Also add #address-cells and #size-cells to prevent more warnings.
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200110134420.11280-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0ff15a86d0c5a3f004fee2e92d65b88e56a3bc58 ]
Add a fixed regulator and use it as power supply for DSI panel.
Fixes: 18c8866266 ("ARM: dts: stm32: Add display support on stm32f469-disco")
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8443ffd1bbd5be74e9b12db234746d12e8ea93e2 ]
Add a device node for the global timer, which is part of the Cortex-A9
MPCore.
The global timer can serve as an accurate (4 ns) clock source for
scheduling and delay loops.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20191211135222.26770-4-geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6bb1e09c4c375db29770444f689f35f5cbe696bc ]
Cabling used to connect devices to USBH1 on RDU2 does not meet USB
spec cable quality and cable length requirements to operate at High
Speed, so limit the port to Full Speed only.
Reported-by: Chris Healy <cphealy@gmail.com>
Reviewed-by: Chris Healy <cphealy@gmail.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit cd58a174e58649426fb43d7456e5f7d7eab58af1 ]
RDU2 production units come with resistor connecting WP pin to
correpsonding GPIO DNPed for both SD card slots. Drop any WP related
configuration and mark both slots with "disable-wp".
Reported-by: Chris Healy <cphealy@gmail.com>
Reviewed-by: Chris Healy <cphealy@gmail.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0388a110747bec0c9d9de995842bb2a03a26aae1 ]
Add the Performance Monitoring Unit (PMU) device tree node to the H3
.dtsi, which tells DT users which interrupts are triggered by PMU
overflow events on each core. The numbers come from the manual and have
been checked in U-Boot and with perf in Linux.
Tested with perf record and taskset on an OrangePi Zero.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit a7e0f3fc01df4b1b7077df777c37feae8c9e8b6d upstream.
The clock rate range for the TCB1 clock is missing. define it in the device
tree.
Reported-by: Karl Rudbæk Olsen <karl@micro-technic.com>
Fixes: d2e8190b7916 ("ARM: at91/dt: define sama5d3 clocks")
Link: https://lore.kernel.org/r/20200110172007.1253659-2-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ee0aa926ddb0bd8ba59e33e3803b3b5804e3f5da upstream.
Currently the maximum rate for peripheral clock is calculated based on a
typical 133MHz MCK. The maximum frequency is defined in the datasheet as a
ratio to MCK. Some sama5d3 platforms are using a 166MHz MCK. Update the
device trees to match the maximum rate based on 166MHz.
Reported-by: Karl Rudbæk Olsen <karl@micro-technic.com>
Fixes: d2e8190b7916 ("ARM: at91/dt: define sama5d3 clocks")
Link: https://lore.kernel.org/r/20200110172007.1253659-1-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
Ludovic Desroches
Hamish Martin
Vincent Stehlé
Robert Beckett
Łukasz Stelmach
Johan Jonker
Geert Uytterhoeven
Michal Vokáč
Fabio Estevam
Kishon Vijay Abraham I
Russell King
Nicolas Saenz Julienne
Jernej Skrabec
Martin Fuzzey
Oleksandr Suvorov
Marek Szyprowski
Tony Lindgren
Ondrej Jirman
Chen-Yu Tsai
Arthur Demchenkov
Marco Felsch
Nick Hudson
Sungbo Eo
Roger Quadros
Grygorii Strashko
Ard Biesheuvel
Suman Anna
Vladimir Oltean
Faiz Abbas
Kuninori Morimoto
Benjamin Gaignard
Andrey Smirnov
Andre Przywara
Alexandre Belloni