| Age | Commit message (Collapse) | Author |
|---|
|
[ Upstream commit f7f9da89bc4f61e33f7b9f5c75c4efdc1f0455d8 ]
The clock controller registers are not 0x460 wide because the reset
controller starts at CBUS 0x4404. This currently overlaps with the
clock controller (which is at CBUS 0x4000).
There is no public documentation available on the actual size of the
clock controller's register area (also called "HHI"). However, in
Amlogic's GPL kernel sources the last "HHI" register is
HHI_HDMI_PHY_CNTL2 at CBUS + 0x43a8. 0x400 was chosen because that size
doesn't seem unlikely.
Fixes: 2c323c43a3d619 ("ARM: dts: meson8: add and use the real clock controller")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8a1ecc01a473b75ab97be9b36f623e4551a6e9ae ]
There is one too many zeroes in the Power I2C base address. Fix this.
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 24a610eba32a80ed778ea79680b600c3fe73d7de ]
The RTC controller is fed by an external fixed 32kHz clock. Yet the
driver wants to acquire this clock, even though it doesn't make any use
of it, ie. doesn't get the rate to make calculation.
Therefore, use the exported 32.768kHz clock in the PXA clock tree to
make the driver happy and working.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f8f3b7fc21b1cb59385b780acd9b9a26d04cb7b2 ]
Regulators, which are marked as 'on-in-suspend' seems to be critical for
board operation, thus they must not be disabled anytime. This can be
only assured by marking them as 'always-on', because otherwise some
actions of their clients might result in turning them off. This patch
restores suspend/resume operation on Peach-Pit Chromebook board. It
partially reverts 'always-on' property removal done by the commit
mentioned in the Fixes tag.
Fixes: 665c441eea3d ("ARM: dts: exynos: Remove unneded always-on for regulators on Peach boards")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 64858773d78e820003a94e5a7179d368213655d6 ]
This patch adds missing properties to the CODEC and sound nodes, so the
audio will work also on Snow rev5 Chromebook. This patch is an extension
to the commit e9eefc3f8ce0 ("ARM: dts: exynos: Add missing clock and
DAI properties to the max98095 node in Snow Chromebook")
and commit 6ab569936d60 ("ARM: dts: exynos: Enable HDMI audio on Snow
Chromebook"). It has been reported that such changes work fine on the
rev5 board too.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
[krzk: Fixed typo in phandle to &max98090]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 21cb5a27483a3cfdbcb7508a06a30c0a485e1211 ]
HDMI-HPD was set active low, moreover by default pincontrol chip sets
pull-down on the pin. As a result HDMI driver assumes TV is always
connected regardless of actual state. The patch fixes it.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 620375c8fdf2f9f5110ed48d6c407cc4b7554f86 ]
HDMI-DDC for unknown reasons doesn't work with Exynos I2C controllers.
Fortunately i2c-gpio comes to the rescue.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 10af10db8c76fa5b9bf1f52a895c1cb2c0ac24da ]
Fix a typo. No functional change made by this patch.
Signed-off-by: Jay Foster <jayfoster@ieee.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 441f61e3aa9e7386731ce1405044d484bd81f911 ]
Update the SATA device nodes on R-Car H1, H2, and M2-W to use a 2 MiB
I/O space, as specified in Rev.1.0 of the R-Car H1 and R-Car Gen2
hardware user manuals.
See also commit e9f0089b2d8a3d45 ("arm64: dts: r8a7795: Correct SATA
device size to 2MiB").
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
This is the 4.19.83 stable release
# gpg: Signature made Sun 10 Nov 2019 05:27:57 AM EST
# gpg: using RSA key 647F28654894E3BD457199BE38DBBDC86092693E
# gpg: Can't check signature: No public key
|
|
This is the 4.19.81 stable release
# gpg: Signature made Tue 29 Oct 2019 04:20:10 AM EDT
# gpg: using RSA key 647F28654894E3BD457199BE38DBBDC86092693E
# gpg: Can't check signature: No public key
|
|
[ Upstream commit 252b9e21bcf46b0d16f733f2e42b21fdc60addee ]
i.MX7S/D's GPT ipg clock should be from GPT clock root and
controlled by CCM's GPT CCGR, using correct clock source for
GPT ipg clock instead of IMX7D_CLK_DUMMY.
Fixes: 3ef79ca6bd1d ("ARM: dts: imx7d: use imx7s.dtsi as base device tree")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6b512b0ee091edcb8e46218894e4c917d919d3dc ]
The TWL4030 used on the Logit PD Torpedo SOM does not have the
keypad pins routed. This patch disables the twl_keypad driver
to remove some splat during boot:
twl4030_keypad 48070000.i2c:twl@48:keypad: missing or malformed property linux,keymap: -22
twl4030_keypad 48070000.i2c:twl@48:keypad: Failed to build keymap
twl4030_keypad: probe of 48070000.i2c:twl@48:keypad failed with error -22
Signed-off-by: Adam Ford <aford173@gmail.com>
[tony@atomide.com: removed error time stamps]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f90ec6cdf674248dcad85bf9af6e064bf472b841 ]
Set memory bandwidth limit to filter out resolutions above 720p@60Hz to
avoid underflow errors due to the bandwidth needs of higher resolutions.
am43xx can not provide enough bandwidth to DISPC to correctly handle
'high' resolutions.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
This is the 4.19.77 stable release
# gpg: Signature made Sat 05 Oct 2019 07:10:18 AM EDT
# gpg: using RSA key 647F28654894E3BD457199BE38DBBDC86092693E
# gpg: Can't check signature: No public key
|
|
This is the 4.19.75 stable release
# gpg: Signature made Sat 21 Sep 2019 01:17:15 AM EDT
# gpg: using RSA key 647F28654894E3BD457199BE38DBBDC86092693E
# gpg: Can't check signature: No public key
|
|
This is the 4.19.73 stable release
# gpg: Signature made Mon 16 Sep 2019 02:22:25 AM EDT
# gpg: using RSA key 647F28654894E3BD457199BE38DBBDC86092693E
# gpg: Can't check signature: No public key
|
|
[ Upstream commit 5b0eeeaa37615df37a9a30929b73e9defe61ca84 ]
Commit aff138bf8e37 ("ARM: dts: exynos: Add TMU nodes regulator supply
for Peach boards") assigned LDO10 to Exynos Thermal Measurement Unit,
but it turned out that it supplies also some other critical parts and
board freezes/crashes when it is turned off.
The mentioned commit made Exynos TMU a consumer of that regulator and in
typical case Exynos TMU driver keeps it enabled from early boot. However
there are such configurations (example is multi_v7_defconfig), in which
some of the regulators are compiled as modules and are not available
from early boot. In such case it may happen that LDO10 is turned off by
regulator core, because it has no consumers yet (in this case consumer
drivers cannot get it, because the supply regulators for it are not yet
available). This in turn causes the board to crash. This patch restores
'always-on' property for the LDO10 regulator.
Fixes: aff138bf8e37 ("ARM: dts: exynos: Add TMU nodes regulator supply for Peach boards")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit a95fbda08ee20cd063ce5826e0df95a2c22ea8c5 ]
Force HS200 by masking bit 63 of the SDHCI capability register.
The i.MX ESDHC driver uses SDHCI_QUIRK2_CAPS_BIT63_FOR_HS400. With
that the stack checks bit 63 to descide whether HS400 is available.
Using sdhci-caps-mask allows to mask bit 63. The stack then selects
HS200 as operating mode.
This prevents rare communication errors with minimal effect on
performance:
sdhci-esdhc-imx 30b60000.usdhc: warning! HS400 strobe DLL
status REF not lock!
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9846a4524ac90b63496580b7ad50674b40d92a8f ]
Recent changes to the atheros at803x driver caused
ethernet to stop working on this board.
In particular commit 6d4cd041f0af
("net: phy: at803x: disable delay only for RGMII mode")
and commit cd28d1d6e52e
("net: phy: at803x: Disable phy delay for RGMII mode")
fix the AR8031 driver to configure the phy's (RX/TX)
delays as per the 'phy-mode' in the device tree.
This now prevents ethernet from working on this board.
It used to work before those commits, because the
AR8031 comes out of reset with RX delay enabled, and
the at803x driver didn't touch the delay configuration
at all when "rgmii" mode was selected, and because
arch/arm/mach-imx/mach-imx7d.c:ar8031_phy_fixup()
unconditionally enables TX delay.
Since above commits ar8031_phy_fixup() also has no
effect anymore, and the end-result is that all delays
are disabled in the phy, no ethernet.
Update the device tree to restore functionality.
Signed-off-by: André Draszik <git@andred.net>
CC: Ilya Ledvich <ilya@compulab.co.il>
CC: Igor Grinberg <grinberg@compulab.co.il>
CC: Rob Herring <robh+dt@kernel.org>
CC: Mark Rutland <mark.rutland@arm.com>
CC: Shawn Guo <shawnguo@kernel.org>
CC: Sascha Hauer <s.hauer@pengutronix.de>
CC: Pengutronix Kernel Team <kernel@pengutronix.de>
CC: Fabio Estevam <festevam@gmail.com>
CC: NXP Linux Team <linux-imx@nxp.com>
CC: devicetree@vger.kernel.org
CC: linux-arm-kernel@lists.infradead.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 07f9a8be66a9bd86f9eaedf8f8aeb416195adab8 ]
According to the latest am572x[1] and dra74x[2] data manuals, mmc3
default, hs, sdr12 and sdr25 modes use iodelay values given in
MMC3_MANUAL1. Set the MODE_SELECT bit for these so that manual mode is
selected and correct iodelay values can be configured.
[1] http://www.ti.com/lit/ds/symlink/am5728.pdf
[2] http://www.ti.com/lit/ds/symlink/dra746.pdf
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit fb59ee37cfe20d10d19568899d1458a58361246c ]
If UHS speed modes are enabled, a compatible SD card switches down to
1.8V during enumeration. If after this a software reboot/crash takes
place and on-chip ROM tries to enumerate the SD card, the difference in
IO voltages (host @ 3.3V and card @ 1.8V) may end up damaging the card.
The fix for this is to have support for power cycling the card in
hardware (with a PORz/soft-reset line causing a power cycle of the
card). Because the beaglebone X15 (rev A,B and C), am57xx-idks and
am57xx-evms don't have this capability, disable voltage switching for
these boards.
The major effect of this is that the maximum supported speed
mode is now high speed(50 MHz) down from SDR104(200 MHz).
commit 88a748419b84 ("ARM: dts: am57xx-idk: Remove support for voltage
switching for SD card") did this only for idk boards. Do it for all
affected boards.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f90b8fda3a9d72a9422ea80ae95843697f94ea4a ]
The SPI to the display on the DIR-685 is active low, we were
just saved by the SPI library enforcing active low on everything
before, so set it as active low to avoid ambiguity.
Link: https://lore.kernel.org/r/20190715202101.16060-1-linus.walleij@linaro.org
Cc: stable@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f3e35357cd460a8aeb48b8113dc4b761a7d5c828 ]
David Bauer reported that the VDSL modem (attached via PCIe)
on his AVM Fritz!Box 7530 was complaining about not having
enough space in the BAR. A closer inspection of the old
qcom-ipq40xx.dtsi pulled from the GL-iNet repository listed:
| qcom,pcie@80000 {
| compatible = "qcom,msm_pcie";
| reg = <0x80000 0x2000>,
| <0x99000 0x800>,
| <0x40000000 0xf1d>,
| <0x40000f20 0xa8>,
| <0x40100000 0x1000>,
| <0x40200000 0x100000>,
| <0x40300000 0xd00000>;
| reg-names = "parf", "phy", "dm_core", "elbi",
| "conf", "io", "bars";
Matching the reg-names with the listed reg leads to
<0xd00000> as the size for the "bars".
Cc: stable@vger.kernel.org
BugLink: https://www.mail-archive.com/openwrt-devel@lists.openwrt.org/msg45212.html
Reported-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Andy Gross <agross@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 97131f85c08e024df49480ed499aae8fb754067f ]
The databook clearly states that the MSI IRQ (msi_ctrl_int) is a level
triggered interrupt.
The msi_ctrl_int will be high for as long as any MSI status bit is set,
thus the IRQ type should be set to IRQ_TYPE_LEVEL_HIGH, causing the
IRQ handler to keep getting called, as long as any MSI status bit is set.
A git grep shows that ipq4019 is the only SoC using snps,dw-pcie that has
configured this IRQ incorrectly.
Not having the correct IRQ type defined will cause us to lose interrupts,
which in turn causes timeouts in the PCIe endpoint drivers.
Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit da89f500cb55fb3f19c4b399b46d8add0abbd4d6 ]
The PCI range is invalid and PCI attached devices doen't work.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
This is the 4.19.67 stable release
|
|
This is the 4.19.65 stable release
|
|
[ Upstream commit 3a9d2569e45cb02769cda26fee4a02126867c934 ]
The mdio-bus-mux has no #address-cells/#size-cells property,
which causes a few dtc warnings:
arch/arm/boot/dts/bcm47094-linksys-panamera.dts:129.4-18: Warning (reg_format): /mdio-bus-mux/mdio@200:reg: property has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1)
arch/arm/boot/dts/bcm47094-linksys-panamera.dtb: Warning (pci_device_bus_num): Failed prerequisite 'reg_format'
arch/arm/boot/dts/bcm47094-linksys-panamera.dtb: Warning (i2c_bus_reg): Failed prerequisite 'reg_format'
arch/arm/boot/dts/bcm47094-linksys-panamera.dtb: Warning (spi_bus_reg): Failed prerequisite 'reg_format'
arch/arm/boot/dts/bcm47094-linksys-panamera.dts:128.22-132.5: Warning (avoid_default_addr_size): /mdio-bus-mux/mdio@200: Relying on default #address-cells value
arch/arm/boot/dts/bcm47094-linksys-panamera.dts:128.22-132.5: Warning (avoid_default_addr_size): /mdio-bus-mux/mdio@200: Relying on default #size-cells value
Add the normal cell numbers.
Link: https://lore.kernel.org/r/20190722145618.1155492-1-arnd@arndb.de
Fixes: 2bebdfcdcd0f ("ARM: dts: BCM5301X: Add support for Linksys EA9500")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8ef1ba39a9fa53d2205e633bc9b21840a275908e ]
This is similar to commit e6186820a745 ("arm64: dts: rockchip: Arch
counter doesn't tick in system suspend"). Specifically on the rk3288
it can be seen that the timer stops ticking in suspend if we end up
running through the "osc_disable" path in rk3288_slp_mode_set(). In
that path the 24 MHz clock will turn off and the timer stops.
To test this, I ran this on a Chrome OS filesystem:
before=$(date); \
suspend_stress_test -c1 --suspend_min=30 --suspend_max=31; \
echo ${before}; date
...and I found that unless I plug in a device that requests USB wakeup
to be active that the two calls to "date" would show that fewer than
30 seconds passed.
NOTE: deep suspend (where the 24 MHz clock gets disabled) isn't
supported yet on upstream Linux so this was tested on a downstream
kernel.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 99fa066710f75f18f4d9a5bc5f6a711968a581d5 ]
When I try to boot rk3288-veyron-mickey I totally fail to make the
eMMC work. Specifically my logs (on Chrome OS 4.19):
mmc_host mmc1: card is non-removable.
mmc_host mmc1: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 52000000Hz, actual 50000000HZ div = 0)
mmc1: switch to bus width 8 failed
mmc1: switch to bus width 4 failed
mmc1: new high speed MMC card at address 0001
mmcblk1: mmc1:0001 HAG2e 14.7 GiB
mmcblk1boot0: mmc1:0001 HAG2e partition 1 4.00 MiB
mmcblk1boot1: mmc1:0001 HAG2e partition 2 4.00 MiB
mmcblk1rpmb: mmc1:0001 HAG2e partition 3 4.00 MiB, chardev (243:0)
mmc_host mmc1: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 52000000Hz, actual 50000000HZ div = 0)
mmc1: switch to bus width 8 failed
mmc1: switch to bus width 4 failed
mmc1: tried to HW reset card, got error -110
mmcblk1: error -110 requesting status
mmcblk1: recovery failed!
print_req_error: I/O error, dev mmcblk1, sector 0
...
When I remove the '/delete-property/mmc-hs200-1_8v' then everything is
hunky dory.
That line comes from the original submission of the mickey dts
upstream, so presumably at the time the HS200 was failing and just
enumerating things as a high speed device was fine. ...or maybe it's
just that some mickey devices work when enumerating at "high speed",
just not mine?
In any case, hs200 seems good now. Let's turn it on.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 1c0479023412ab7834f2e98b796eb0d8c627cd62 ]
As some point hs200 was failing on rk3288-veyron-minnie. See commit
984926781122 ("ARM: dts: rockchip: temporarily remove emmc hs200 speed
from rk3288 minnie"). Although I didn't track down exactly when it
started working, it seems to work OK now, so let's turn it back on.
To test this, I booted from SD card and then used this script to
stress the enumeration process after fixing a memory leak [1]:
cd /sys/bus/platform/drivers/dwmmc_rockchip
for i in $(seq 1 3000); do
echo "========================" $i
echo ff0f0000.dwmmc > unbind
sleep .5
echo ff0f0000.dwmmc > bind
while true; do
if [ -e /dev/mmcblk2 ]; then
break;
fi
sleep .1
done
done
It worked fine.
[1] https://lkml.kernel.org/r/20190503233526.226272-1-dianders@chromium.org
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
This is the 4.19.60 stable release
|
|
This is the 4.19.59 stable release
|
|
This is the 4.19.58 stable release
|
|
[ Upstream commit 3cf10132ac8d536565f2c02f60a3aeb315863a52 ]
According to the i.MX6UL/L RM, table 3.1 "ARM Cortex A7 domain interrupt
summary", the interrupts for the PWM[1-4] go from 83 to 86.
Fixes: b9901fe84f02 ("ARM: dts: imx6ul: add pwm[1-4] nodes")
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 36558020128b1a48b7bddd5792ee70e3f64b04b0 ]
It's a simple typo in the DNS file, which was pretty serious.
No scripts were working properly. Fix it up.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8a0098c05a272c9a68f6885e09755755b612459c ]
Active level of the mmc1 cd gpio needs to be low instead of high.
Fix PCM-953 and phyBOARD-WEGA.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 80031361747aec92163464f2ee08870fec33bcb0 upstream.
Switch to the "marvell,armada-38x-uart" driver variant to empty
the UART buffer before writing to the UART_LCR register.
Signed-off-by: Joshua Scott <joshua.scott@alliedtelesis.co.nz>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com>.
Cc: stable@vger.kernel.org
Fixes: 43e28ba87708 ("ARM: dts: Use armada-370-xp as a base for armada-xp-98dx3236")
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This is the 4.19.56 stable release
|
|
This is the 4.19.51 stable release
|
|
This is the 4.19.45 stable release
|
|
commit 88a748419b84187fd1da05637b8e5928b04a1e06 upstream.
If UHS speed modes are enabled, a compatible SD card switches down to
1.8V during enumeration. If after this a software reboot/crash takes
place and on-chip ROM tries to enumerate the SD card, the difference in
IO voltages (host @ 3.3V and card @ 1.8V) may end up damaging the card.
The fix for this is to have support for power cycling the card in
hardware (with a PORz/soft-reset line causing a power cycle of the
card). Since am571x-, am572x- and am574x-idk don't have this
capability, disable voltage switching for these boards.
The major effect of this is that the maximum supported speed
mode is now high speed(50 MHz) down from SDR104(200 MHz).
Cc: <stable@vger.kernel.org>
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c3c0b70cd3f801bded7a548198ee1c9851a0ca82 upstream.
Update the MMC2_HS200_MANUAL1 iodelay values to match with the latest
dra76x data manual[1]. The new iodelay values will have better marginality
and should prevent issues in corner cases.
Also this particular pinctrl-array is using spaces instead of tabs for
spacing between the values and the comments. Fix this as well.
[1] http://www.ti.com/lit/ds/symlink/dra76p.pdf
Cc: <stable@vger.kernel.org>
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
[tony@atomide.com: updated description with a bit more info]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Arndale Octa
[ Upstream commit 5ab99cf7d5e96e3b727c30e7a8524c976bd3723d ]
The PVDD_APIO_1V8 (LDO2) and PVDD_ABB_1V8 (LDO8) regulators were turned
off by Linux kernel as unused. However they supply critical parts of
SoC so they should be always on:
1. PVDD_APIO_1V8 supplies SYS pins (gpx[0-3], PSHOLD), HDMI level shift,
RTC, VDD1_12 (DRAM internal 1.8 V logic), pull-up for PMIC interrupt
lines, TTL/UARTR level shift, reset pins and SW-TACT1 button.
It also supplies unused blocks like VDDQ_SRAM (for SROM controller) and
VDDQ_GPIO (gpm7, gpy7).
The LDO2 cannot be turned off (S2MPS11 keeps it on anyway) so
marking it "always-on" only reflects its real status.
2. PVDD_ABB_1V8 supplies Adaptive Body Bias Generator for ARM cores,
memory and Mali (G3D).
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b14c872eebc501b9640b04f4a152df51d6eaf2fc ]
Since 25aaa75df1e6 SDMA driver uses clock rates of "ipg" and "ahb"
clock to determine if it needs to configure the IP block as operating
at 1:1 or 1:2 clock ratio (ACR bit in SDMAARM_CONFIG). Specifying both
clocks as IMX6QDL_CLK_SDMA results in driver incorrectly thinking that
ratio is 1:1 which results in broken SDMA funtionality(this at least
breaks RAVE SP serdev driver on RDU2). Fix the code to specify
IMX6QDL_CLK_IPG as "ipg" clock for SDMA, to avoid detecting incorrect
clock ratio.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Cc: Angus Ainslie (Purism) <angus@akkea.ca>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Tested-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8979117765c19edc3b01cc0ef853537bf93eea4b ]
Since 25aaa75df1e6 SDMA driver uses clock rates of "ipg" and "ahb"
clock to determine if it needs to configure the IP block as operating
at 1:1 or 1:2 clock ratio (ACR bit in SDMAARM_CONFIG). Specifying both
clocks as IMX6SX_CLK_SDMA results in driver incorrectly thinking that
ratio is 1:1 which results in broken SDMA funtionality. Fix the code
to specify IMX6SX_CLK_IPG as "ipg" clock for SDMA, to avoid detecting
incorrect clock ratio.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Angus Ainslie (Purism) <angus@akkea.ca>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 7b3132ecefdd1fcdf6b86e62021d0e55ea8034db ]
Since 25aaa75df1e6 SDMA driver uses clock rates of "ipg" and "ahb"
clock to determine if it needs to configure the IP block as operating
at 1:1 or 1:2 clock ratio (ACR bit in SDMAARM_CONFIG). Specifying both
clocks as IMX6UL_CLK_SDMA results in driver incorrectly thinking that
ratio is 1:1 which results in broken SDMA funtionality. Fix the code
to specify IMX6UL_CLK_IPG as "ipg" clock for SDMA, to avoid detecting
incorrect clock ratio.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Angus Ainslie (Purism) <angus@akkea.ca>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 412b032a1dc72fc9d1c258800355efa6671b6315 ]
Since 25aaa75df1e6 SDMA driver uses clock rates of "ipg" and "ahb"
clock to determine if it needs to configure the IP block as operating
at 1:1 or 1:2 clock ratio (ACR bit in SDMAARM_CONFIG). Specifying both
clocks as IMX7D_CLK_SDMA results in driver incorrectly thinking that
ratio is 1:1 which results in broken SDMA funtionality. Fix the code
to specify IMX7D_CLK_IPG as "ipg" clock for SDMA, to avoid detecting
incorrect clock ratio.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Angus Ainslie (Purism) <angus@akkea.ca>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c5ed5daa65d5f665e666b76c3dbfa503066defde ]
Since 25aaa75df1e6 SDMA driver uses clock rates of "ipg" and "ahb"
clock to determine if it needs to configure the IP block as operating
at 1:1 or 1:2 clock ratio (ACR bit in SDMAARM_CONFIG). Specifying both
clocks as IMX6SLL_CLK_SDMA result in driver incorrectly thinking that
ratio is 1:1 which results in broken SDMA funtionality. Fix the code
to specify IMX6SLL_CLK_IPG as "ipg" clock for SDMA, to avoid detecting
incorrect clock ratio.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Angus Ainslie (Purism) <angus@akkea.ca>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
Martin Blumenstingl
Marcel Ziswiler
Robert Jarzmik
Marek Szyprowski
Andrzej Hajda
Jay Foster
Geert Uytterhoeven
Bruce Ashfield
Anson Huang
Adam Ford
Peter Ujfalusi
Stefan Agner
André Draszik
Faiz Abbas
Linus Walleij
Christian Lamparter
Niklas Cassel
Mathias Kresin
Arnd Bergmann
Douglas Anderson
Sébastien Szymanski
Teresa Remmet
Joshua Scott
Krzysztof Kozlowski
Andrey Smirnov