| Age | Commit message (Collapse) | Author |
|---|
|
This is the 4.14.154 stable release
# gpg: Signature made Tue 12 Nov 2019 01:19:09 PM EST
# gpg: using RSA key 647F28654894E3BD457199BE38DBBDC86092693E
# gpg: Can't check signature: No public key
|
|
This is the 4.14.153 stable release
# gpg: Signature made Sun 10 Nov 2019 05:25:43 AM EST
# gpg: using RSA key 647F28654894E3BD457199BE38DBBDC86092693E
# gpg: Can't check signature: No public key
|
|
This is the 4.14.151 stable release
# gpg: Signature made Tue 29 Oct 2019 04:17:49 AM EDT
# gpg: using RSA key 647F28654894E3BD457199BE38DBBDC86092693E
# gpg: Can't check signature: No public key
|
|
commit b8c9c6fa2002b8fd4a9710f76f80f99c6046d48c upstream.
The metastability workaround causes Erratic errors [1]
on the HighSpeed USB PHY which can cause upto 2 seconds
delay in enumerating to a USB host while in Gadget mode.
Disable the Run/Stop metastability workaround to avoid this
ill effect. We are aware that this opens up the opportunity
for Run/Stop metastability, however this issue has never been
observed in TI releases so we think that Run/Stop metastability
is a lesser evil than the PHY Erratic errors. So disable it.
[1] USB controller trace during gadget enumeration
irq/90-dwc3-969 [000] d... 52.323145: dwc3_event: event
(00000901): Erratic Error [U0]
irq/90-dwc3-969 [000] d... 52.560646: dwc3_event: event
(00000901): Erratic Error [U0]
irq/90-dwc3-969 [000] d... 52.798144: dwc3_event: event
(00000901): Erratic Error [U0]
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Felipe Balbi <felipe.balbi@linux/intel.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 252b9e21bcf46b0d16f733f2e42b21fdc60addee ]
i.MX7S/D's GPT ipg clock should be from GPT clock root and
controlled by CCM's GPT CCGR, using correct clock source for
GPT ipg clock instead of IMX7D_CLK_DUMMY.
Fixes: 3ef79ca6bd1d ("ARM: dts: imx7d: use imx7s.dtsi as base device tree")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6b512b0ee091edcb8e46218894e4c917d919d3dc ]
The TWL4030 used on the Logit PD Torpedo SOM does not have the
keypad pins routed. This patch disables the twl_keypad driver
to remove some splat during boot:
twl4030_keypad 48070000.i2c:twl@48:keypad: missing or malformed property linux,keymap: -22
twl4030_keypad 48070000.i2c:twl@48:keypad: Failed to build keymap
twl4030_keypad: probe of 48070000.i2c:twl@48:keypad failed with error -22
Signed-off-by: Adam Ford <aford173@gmail.com>
[tony@atomide.com: removed error time stamps]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f90ec6cdf674248dcad85bf9af6e064bf472b841 ]
Set memory bandwidth limit to filter out resolutions above 720p@60Hz to
avoid underflow errors due to the bandwidth needs of higher resolutions.
am43xx can not provide enough bandwidth to DISPC to correctly handle
'high' resolutions.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
This is the 4.14.147 stable release
# gpg: Signature made Sat 05 Oct 2019 06:48:15 AM EDT
# gpg: using RSA key 647F28654894E3BD457199BE38DBBDC86092693E
# gpg: Can't check signature: No public key
|
|
This is the 4.14.146 stable release
# gpg: Signature made Sat 21 Sep 2019 01:15:48 AM EDT
# gpg: using RSA key 647F28654894E3BD457199BE38DBBDC86092693E
# gpg: Can't check signature: No public key
|
|
[ Upstream commit 5b0eeeaa37615df37a9a30929b73e9defe61ca84 ]
Commit aff138bf8e37 ("ARM: dts: exynos: Add TMU nodes regulator supply
for Peach boards") assigned LDO10 to Exynos Thermal Measurement Unit,
but it turned out that it supplies also some other critical parts and
board freezes/crashes when it is turned off.
The mentioned commit made Exynos TMU a consumer of that regulator and in
typical case Exynos TMU driver keeps it enabled from early boot. However
there are such configurations (example is multi_v7_defconfig), in which
some of the regulators are compiled as modules and are not available
from early boot. In such case it may happen that LDO10 is turned off by
regulator core, because it has no consumers yet (in this case consumer
drivers cannot get it, because the supply regulators for it are not yet
available). This in turn causes the board to crash. This patch restores
'always-on' property for the LDO10 regulator.
Fixes: aff138bf8e37 ("ARM: dts: exynos: Add TMU nodes regulator supply for Peach boards")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9846a4524ac90b63496580b7ad50674b40d92a8f ]
Recent changes to the atheros at803x driver caused
ethernet to stop working on this board.
In particular commit 6d4cd041f0af
("net: phy: at803x: disable delay only for RGMII mode")
and commit cd28d1d6e52e
("net: phy: at803x: Disable phy delay for RGMII mode")
fix the AR8031 driver to configure the phy's (RX/TX)
delays as per the 'phy-mode' in the device tree.
This now prevents ethernet from working on this board.
It used to work before those commits, because the
AR8031 comes out of reset with RX delay enabled, and
the at803x driver didn't touch the delay configuration
at all when "rgmii" mode was selected, and because
arch/arm/mach-imx/mach-imx7d.c:ar8031_phy_fixup()
unconditionally enables TX delay.
Since above commits ar8031_phy_fixup() also has no
effect anymore, and the end-result is that all delays
are disabled in the phy, no ethernet.
Update the device tree to restore functionality.
Signed-off-by: André Draszik <git@andred.net>
CC: Ilya Ledvich <ilya@compulab.co.il>
CC: Igor Grinberg <grinberg@compulab.co.il>
CC: Rob Herring <robh+dt@kernel.org>
CC: Mark Rutland <mark.rutland@arm.com>
CC: Shawn Guo <shawnguo@kernel.org>
CC: Sascha Hauer <s.hauer@pengutronix.de>
CC: Pengutronix Kernel Team <kernel@pengutronix.de>
CC: Fabio Estevam <festevam@gmail.com>
CC: NXP Linux Team <linux-imx@nxp.com>
CC: devicetree@vger.kernel.org
CC: linux-arm-kernel@lists.infradead.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 07f9a8be66a9bd86f9eaedf8f8aeb416195adab8 ]
According to the latest am572x[1] and dra74x[2] data manuals, mmc3
default, hs, sdr12 and sdr25 modes use iodelay values given in
MMC3_MANUAL1. Set the MODE_SELECT bit for these so that manual mode is
selected and correct iodelay values can be configured.
[1] http://www.ti.com/lit/ds/symlink/am5728.pdf
[2] http://www.ti.com/lit/ds/symlink/dra746.pdf
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
This is the 4.14.138 stable release
|
|
This is the 4.14.137 stable release
|
|
This is the 4.14.134 stable release
|
|
This is the 4.14.130 stable release
|
|
This is the 4.14.126 stable release
|
|
This is the 4.14.121 stable release
|
|
[ Upstream commit a135a392acbec7ecda782981788e8c03767a1571 ]
Since I2C1 and I2C4 have explicit pinmuxing set, let's be on the
safe side and set the pin muxing for I2C2 and I2C3.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5fe3c0fa0d54877c65e7c9b4442aeeb25cdf469a ]
Since I2C1 and I2C4 have explicit pinmuxing set, let's be on the
safe side and set the pin muxing for I2C2 and I2C3.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8ef1ba39a9fa53d2205e633bc9b21840a275908e ]
This is similar to commit e6186820a745 ("arm64: dts: rockchip: Arch
counter doesn't tick in system suspend"). Specifically on the rk3288
it can be seen that the timer stops ticking in suspend if we end up
running through the "osc_disable" path in rk3288_slp_mode_set(). In
that path the 24 MHz clock will turn off and the timer stops.
To test this, I ran this on a Chrome OS filesystem:
before=$(date); \
suspend_stress_test -c1 --suspend_min=30 --suspend_max=31; \
echo ${before}; date
...and I found that unless I plug in a device that requests USB wakeup
to be active that the two calls to "date" would show that fewer than
30 seconds passed.
NOTE: deep suspend (where the 24 MHz clock gets disabled) isn't
supported yet on upstream Linux so this was tested on a downstream
kernel.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 99fa066710f75f18f4d9a5bc5f6a711968a581d5 ]
When I try to boot rk3288-veyron-mickey I totally fail to make the
eMMC work. Specifically my logs (on Chrome OS 4.19):
mmc_host mmc1: card is non-removable.
mmc_host mmc1: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 52000000Hz, actual 50000000HZ div = 0)
mmc1: switch to bus width 8 failed
mmc1: switch to bus width 4 failed
mmc1: new high speed MMC card at address 0001
mmcblk1: mmc1:0001 HAG2e 14.7 GiB
mmcblk1boot0: mmc1:0001 HAG2e partition 1 4.00 MiB
mmcblk1boot1: mmc1:0001 HAG2e partition 2 4.00 MiB
mmcblk1rpmb: mmc1:0001 HAG2e partition 3 4.00 MiB, chardev (243:0)
mmc_host mmc1: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 52000000Hz, actual 50000000HZ div = 0)
mmc1: switch to bus width 8 failed
mmc1: switch to bus width 4 failed
mmc1: tried to HW reset card, got error -110
mmcblk1: error -110 requesting status
mmcblk1: recovery failed!
print_req_error: I/O error, dev mmcblk1, sector 0
...
When I remove the '/delete-property/mmc-hs200-1_8v' then everything is
hunky dory.
That line comes from the original submission of the mickey dts
upstream, so presumably at the time the HS200 was failing and just
enumerating things as a high speed device was fine. ...or maybe it's
just that some mickey devices work when enumerating at "high speed",
just not mine?
In any case, hs200 seems good now. Let's turn it on.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 1c0479023412ab7834f2e98b796eb0d8c627cd62 ]
As some point hs200 was failing on rk3288-veyron-minnie. See commit
984926781122 ("ARM: dts: rockchip: temporarily remove emmc hs200 speed
from rk3288 minnie"). Although I didn't track down exactly when it
started working, it seems to work OK now, so let's turn it back on.
To test this, I booted from SD card and then used this script to
stress the enumeration process after fixing a memory leak [1]:
cd /sys/bus/platform/drivers/dwmmc_rockchip
for i in $(seq 1 3000); do
echo "========================" $i
echo ff0f0000.dwmmc > unbind
sleep .5
echo ff0f0000.dwmmc > bind
while true; do
if [ -e /dev/mmcblk2 ]; then
break;
fi
sleep .1
done
done
It worked fine.
[1] https://lkml.kernel.org/r/20190503233526.226272-1-dianders@chromium.org
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 3cf10132ac8d536565f2c02f60a3aeb315863a52 ]
According to the i.MX6UL/L RM, table 3.1 "ARM Cortex A7 domain interrupt
summary", the interrupts for the PWM[1-4] go from 83 to 86.
Fixes: b9901fe84f02 ("ARM: dts: imx6ul: add pwm[1-4] nodes")
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8a0098c05a272c9a68f6885e09755755b612459c ]
Active level of the mmc1 cd gpio needs to be low instead of high.
Fix PCM-953 and phyBOARD-WEGA.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 88a748419b84187fd1da05637b8e5928b04a1e06 upstream.
If UHS speed modes are enabled, a compatible SD card switches down to
1.8V during enumeration. If after this a software reboot/crash takes
place and on-chip ROM tries to enumerate the SD card, the difference in
IO voltages (host @ 3.3V and card @ 1.8V) may end up damaging the card.
The fix for this is to have support for power cycling the card in
hardware (with a PORz/soft-reset line causing a power cycle of the
card). Since am571x-, am572x- and am574x-idk don't have this
capability, disable voltage switching for these boards.
The major effect of this is that the maximum supported speed
mode is now high speed(50 MHz) down from SDR104(200 MHz).
Cc: <stable@vger.kernel.org>
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Arndale Octa
[ Upstream commit 5ab99cf7d5e96e3b727c30e7a8524c976bd3723d ]
The PVDD_APIO_1V8 (LDO2) and PVDD_ABB_1V8 (LDO8) regulators were turned
off by Linux kernel as unused. However they supply critical parts of
SoC so they should be always on:
1. PVDD_APIO_1V8 supplies SYS pins (gpx[0-3], PSHOLD), HDMI level shift,
RTC, VDD1_12 (DRAM internal 1.8 V logic), pull-up for PMIC interrupt
lines, TTL/UARTR level shift, reset pins and SW-TACT1 button.
It also supplies unused blocks like VDDQ_SRAM (for SROM controller) and
VDDQ_GPIO (gpm7, gpy7).
The LDO2 cannot be turned off (S2MPS11 keeps it on anyway) so
marking it "always-on" only reflects its real status.
2. PVDD_ABB_1V8 supplies Adaptive Body Bias Generator for ARM cores,
memory and Mali (G3D).
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b14c872eebc501b9640b04f4a152df51d6eaf2fc ]
Since 25aaa75df1e6 SDMA driver uses clock rates of "ipg" and "ahb"
clock to determine if it needs to configure the IP block as operating
at 1:1 or 1:2 clock ratio (ACR bit in SDMAARM_CONFIG). Specifying both
clocks as IMX6QDL_CLK_SDMA results in driver incorrectly thinking that
ratio is 1:1 which results in broken SDMA funtionality(this at least
breaks RAVE SP serdev driver on RDU2). Fix the code to specify
IMX6QDL_CLK_IPG as "ipg" clock for SDMA, to avoid detecting incorrect
clock ratio.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Cc: Angus Ainslie (Purism) <angus@akkea.ca>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Tested-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8979117765c19edc3b01cc0ef853537bf93eea4b ]
Since 25aaa75df1e6 SDMA driver uses clock rates of "ipg" and "ahb"
clock to determine if it needs to configure the IP block as operating
at 1:1 or 1:2 clock ratio (ACR bit in SDMAARM_CONFIG). Specifying both
clocks as IMX6SX_CLK_SDMA results in driver incorrectly thinking that
ratio is 1:1 which results in broken SDMA funtionality. Fix the code
to specify IMX6SX_CLK_IPG as "ipg" clock for SDMA, to avoid detecting
incorrect clock ratio.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Angus Ainslie (Purism) <angus@akkea.ca>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 7b3132ecefdd1fcdf6b86e62021d0e55ea8034db ]
Since 25aaa75df1e6 SDMA driver uses clock rates of "ipg" and "ahb"
clock to determine if it needs to configure the IP block as operating
at 1:1 or 1:2 clock ratio (ACR bit in SDMAARM_CONFIG). Specifying both
clocks as IMX6UL_CLK_SDMA results in driver incorrectly thinking that
ratio is 1:1 which results in broken SDMA funtionality. Fix the code
to specify IMX6UL_CLK_IPG as "ipg" clock for SDMA, to avoid detecting
incorrect clock ratio.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Angus Ainslie (Purism) <angus@akkea.ca>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 412b032a1dc72fc9d1c258800355efa6671b6315 ]
Since 25aaa75df1e6 SDMA driver uses clock rates of "ipg" and "ahb"
clock to determine if it needs to configure the IP block as operating
at 1:1 or 1:2 clock ratio (ACR bit in SDMAARM_CONFIG). Specifying both
clocks as IMX7D_CLK_SDMA results in driver incorrectly thinking that
ratio is 1:1 which results in broken SDMA funtionality. Fix the code
to specify IMX7D_CLK_IPG as "ipg" clock for SDMA, to avoid detecting
incorrect clock ratio.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Angus Ainslie (Purism) <angus@akkea.ca>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit cc839d0f8c284fcb7591780b568f13415bbb737c ]
Since 25aaa75df1e6 SDMA driver uses clock rates of "ipg" and "ahb"
clock to determine if it needs to configure the IP block as operating
at 1:1 or 1:2 clock ratio (ACR bit in SDMAARM_CONFIG). Specifying both
clocks as IMX6SL_CLK_SDMA results in driver incorrectly thinking that
ratio is 1:1 which results in broken SDMA funtionality. Fix the code
to specify IMX6SL_CLK_AHB as "ahb" clock for SDMA, to avoid detecting
incorrect clock ratio.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Angus Ainslie (Purism) <angus@akkea.ca>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 28c168018e0902c67eb9c60d0fc4c8aa166c4efe ]
Since 25aaa75df1e6 SDMA driver uses clock rates of "ipg" and "ahb"
clock to determine if it needs to configure the IP block as operating
at 1:1 or 1:2 clock ratio (ACR bit in SDMAARM_CONFIG). Specifying both
clocks as IMX5_CLK_SDMA results in driver incorrectly thinking that
ratio is 1:1 which results in broken SDMA funtionality. Fix the code
to specify IMX5_CLK_AHB as "ahb" clock for SDMA, to avoid detecting
incorrect clock ratio.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Angus Ainslie (Purism) <angus@akkea.ca>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b7b4fda2636296471e29b78c2aa9535d7bedb7a0 ]
Since 25aaa75df1e6 SDMA driver uses clock rates of "ipg" and "ahb"
clock to determine if it needs to configure the IP block as operating
at 1:1 or 1:2 clock ratio (ACR bit in SDMAARM_CONFIG). Specifying both
clocks as IMX5_CLK_SDMA results in driver incorrectly thinking that
ratio is 1:1 which results in broken SDMA funtionality. Fix the code
to specify IMX5_CLK_AHB as "ahb" clock for SDMA, to avoid detecting
incorrect clock ratio.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Angus Ainslie (Purism) <angus@akkea.ca>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 918bbde8085ae147a43dcb491953e0dd8f3e9d6a ]
Since 25aaa75df1e6 SDMA driver uses clock rates of "ipg" and "ahb"
clock to determine if it needs to configure the IP block as operating
at 1:1 or 1:2 clock ratio (ACR bit in SDMAARM_CONFIG). Specifying both
clocks as IMX5_CLK_SDMA results in driver incorrectly thinking that
ratio is 1:1 which results in broken SDMA funtionality. Fix the code
to specify IMX5_CLK_AHB as "ahb" clock for SDMA, to avoid detecting
incorrect clock ratio.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Angus Ainslie (Purism) <angus@akkea.ca>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 9b23e1a3e8fde76e8cc0e366ab1ed4ffb4440feb upstream.
The name of CODEC input widget to which microphone is connected through
the "Headphone" jack is "IN12" not "IN1". This fixes microphone support
on Odroid XU3.
Cc: <stable@vger.kernel.org> # v4.14+
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b7ed69d67ff0788d8463e599dd5dd1b45c701a7e upstream.
Fix the interrupt information for the GPIO lines with a shared EINT
interrupt.
Fixes: 16d7ff2642e7 ("ARM: dts: add dts files for exynos5260 SoC")
Cc: stable@vger.kernel.org
Signed-off-by: Stuart Menefy <stuart.menefy@mathembedded.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This is the 4.14.117 stable release
|
|
This is the 4.14.116 stable release
|
|
This is the 4.14.115 stable release
|
|
This is the 4.14.112 stable release
|
|
This is the 4.14.111 stable release
|
|
This is the 4.14.106 stable release
|
|
This is the 4.14.102 stable release
|
|
This is the 4.14.99 stable release
|
|
[ Upstream commit d040e4e8deeaa8257d6aa260e29ad69832b5d630 ]
The device tree compiler yells like this:
Warning (unit_address_vs_reg):
/gpu-opp-table/opp@100000000:
node has a unit name, but no reg property
Let's match the cpu opp node names and use a dash.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 41b37f4c0fa67185691bcbd30201cad566f2f0d1 ]
This patch fixes a spelling typo.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Fixes: cc42603de320 ("ARM: dts: imx6q-icore-rqs: Add Engicam IMX6 Q7 initial support")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
|
|
[ Upstream commit 032f85c9360fb1a08385c584c2c4ed114b33c260 ]
Increase the reset duration to ensure correct phy functionality. The
reset duration is taken from barebox commit 52fdd510de ("ARM: dts:
pfla02: use long enough reset for ethernet phy"):
Use a longer reset time for ethernet phy Micrel KSZ9031RNX. Otherwise a
small percentage of modules have 'transmission timeouts' errors like
barebox@Phytec phyFLEX-i.MX6 Quad Carrier-Board:/ ifup eth0
warning: No MAC address set. Using random address 7e:94:4d:02:f8:f3
eth0: 1000Mbps full duplex link detected
eth0: transmission timeout
T eth0: transmission timeout
T eth0: transmission timeout
T eth0: transmission timeout
T eth0: transmission timeout
Cc: Stefan Christ <s.christ@phytec.de>
Cc: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Fixes: 3180f956668e ("ARM: dts: Phytec imx6q pfla02 and pbab01 support")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
|
|
[ Upstream commit 544e784188f1dd7c797c70b213385e67d92005b6 ]
Raspberry pi board model B revison 2 have the hot plug detector gpio
active high (and not low as it was in the dts).
Signed-off-by: Helen Koike <helen.koike@collabora.com>
Fixes: 49ac67e0c39c ("ARM: bcm2835: Add VC4 to the device tree.")
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
|
|
commit e17b1af96b2afc38e684aa2f1033387e2ed10029 upstream.
The EFI stub is entered with the caches and MMU enabled by the
firmware, and once the stub is ready to hand over to the decompressor,
we clean and disable the caches.
The cache clean routines use CP15 barrier instructions, which can be
disabled via SCTLR. Normally, when using the provided cache handling
routines to enable the caches and MMU, this bit is enabled as well.
However, but since we entered the stub with the caches already enabled,
this routine is not executed before we call the cache clean routines,
resulting in undefined instruction exceptions if the firmware never
enabled this bit.
So set the bit explicitly in the EFI entry code, but do so in a way that
guarantees that the resulting code can still run on v6 cores as well
(which are guaranteed to have CP15 barriers enabled)
Cc: <stable@vger.kernel.org> # v4.9+
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
Bruce Ashfield
Roger Quadros
Anson Huang
Adam Ford
Peter Ujfalusi
Marek Szyprowski
André Draszik
Faiz Abbas
Douglas Anderson
Sébastien Szymanski
Teresa Remmet
Krzysztof Kozlowski
Andrey Smirnov
Sylwester Nawrocki
Stuart Menefy
Masanari Iida
Marco Felsch
Helen Koike
Ard Biesheuvel