| Age | Commit message (Collapse) | Author |
|---|
|
Arndale Octa
commit 5ab99cf7d5e96e3b727c30e7a8524c976bd3723d upstream.
The PVDD_APIO_1V8 (LDO2) and PVDD_ABB_1V8 (LDO8) regulators were turned
off by Linux kernel as unused. However they supply critical parts of
SoC so they should be always on:
1. PVDD_APIO_1V8 supplies SYS pins (gpx[0-3], PSHOLD), HDMI level shift,
RTC, VDD1_12 (DRAM internal 1.8 V logic), pull-up for PMIC interrupt
lines, TTL/UARTR level shift, reset pins and SW-TACT1 button.
It also supplies unused blocks like VDDQ_SRAM (for SROM controller) and
VDDQ_GPIO (gpm7, gpy7).
The LDO2 cannot be turned off (S2MPS11 keeps it on anyway) so
marking it "always-on" only reflects its real status.
2. PVDD_ABB_1V8 supplies Adaptive Body Bias Generator for ARM cores,
memory and Mali (G3D).
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit b14c872eebc501b9640b04f4a152df51d6eaf2fc upstream.
Since 25aaa75df1e6 SDMA driver uses clock rates of "ipg" and "ahb"
clock to determine if it needs to configure the IP block as operating
at 1:1 or 1:2 clock ratio (ACR bit in SDMAARM_CONFIG). Specifying both
clocks as IMX6QDL_CLK_SDMA results in driver incorrectly thinking that
ratio is 1:1 which results in broken SDMA funtionality(this at least
breaks RAVE SP serdev driver on RDU2). Fix the code to specify
IMX6QDL_CLK_IPG as "ipg" clock for SDMA, to avoid detecting incorrect
clock ratio.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Cc: Angus Ainslie (Purism) <angus@akkea.ca>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Tested-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 8979117765c19edc3b01cc0ef853537bf93eea4b upstream.
Since 25aaa75df1e6 SDMA driver uses clock rates of "ipg" and "ahb"
clock to determine if it needs to configure the IP block as operating
at 1:1 or 1:2 clock ratio (ACR bit in SDMAARM_CONFIG). Specifying both
clocks as IMX6SX_CLK_SDMA results in driver incorrectly thinking that
ratio is 1:1 which results in broken SDMA funtionality. Fix the code
to specify IMX6SX_CLK_IPG as "ipg" clock for SDMA, to avoid detecting
incorrect clock ratio.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Angus Ainslie (Purism) <angus@akkea.ca>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 7b3132ecefdd1fcdf6b86e62021d0e55ea8034db upstream.
Since 25aaa75df1e6 SDMA driver uses clock rates of "ipg" and "ahb"
clock to determine if it needs to configure the IP block as operating
at 1:1 or 1:2 clock ratio (ACR bit in SDMAARM_CONFIG). Specifying both
clocks as IMX6UL_CLK_SDMA results in driver incorrectly thinking that
ratio is 1:1 which results in broken SDMA funtionality. Fix the code
to specify IMX6UL_CLK_IPG as "ipg" clock for SDMA, to avoid detecting
incorrect clock ratio.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Angus Ainslie (Purism) <angus@akkea.ca>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 412b032a1dc72fc9d1c258800355efa6671b6315 upstream.
Since 25aaa75df1e6 SDMA driver uses clock rates of "ipg" and "ahb"
clock to determine if it needs to configure the IP block as operating
at 1:1 or 1:2 clock ratio (ACR bit in SDMAARM_CONFIG). Specifying both
clocks as IMX7D_CLK_SDMA results in driver incorrectly thinking that
ratio is 1:1 which results in broken SDMA funtionality. Fix the code
to specify IMX7D_CLK_IPG as "ipg" clock for SDMA, to avoid detecting
incorrect clock ratio.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Angus Ainslie (Purism) <angus@akkea.ca>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit cc839d0f8c284fcb7591780b568f13415bbb737c upstream.
Since 25aaa75df1e6 SDMA driver uses clock rates of "ipg" and "ahb"
clock to determine if it needs to configure the IP block as operating
at 1:1 or 1:2 clock ratio (ACR bit in SDMAARM_CONFIG). Specifying both
clocks as IMX6SL_CLK_SDMA results in driver incorrectly thinking that
ratio is 1:1 which results in broken SDMA funtionality. Fix the code
to specify IMX6SL_CLK_AHB as "ahb" clock for SDMA, to avoid detecting
incorrect clock ratio.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Angus Ainslie (Purism) <angus@akkea.ca>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 28c168018e0902c67eb9c60d0fc4c8aa166c4efe upstream.
Since 25aaa75df1e6 SDMA driver uses clock rates of "ipg" and "ahb"
clock to determine if it needs to configure the IP block as operating
at 1:1 or 1:2 clock ratio (ACR bit in SDMAARM_CONFIG). Specifying both
clocks as IMX5_CLK_SDMA results in driver incorrectly thinking that
ratio is 1:1 which results in broken SDMA funtionality. Fix the code
to specify IMX5_CLK_AHB as "ahb" clock for SDMA, to avoid detecting
incorrect clock ratio.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Angus Ainslie (Purism) <angus@akkea.ca>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit b7b4fda2636296471e29b78c2aa9535d7bedb7a0 upstream.
Since 25aaa75df1e6 SDMA driver uses clock rates of "ipg" and "ahb"
clock to determine if it needs to configure the IP block as operating
at 1:1 or 1:2 clock ratio (ACR bit in SDMAARM_CONFIG). Specifying both
clocks as IMX5_CLK_SDMA results in driver incorrectly thinking that
ratio is 1:1 which results in broken SDMA funtionality. Fix the code
to specify IMX5_CLK_AHB as "ahb" clock for SDMA, to avoid detecting
incorrect clock ratio.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Angus Ainslie (Purism) <angus@akkea.ca>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 918bbde8085ae147a43dcb491953e0dd8f3e9d6a upstream.
Since 25aaa75df1e6 SDMA driver uses clock rates of "ipg" and "ahb"
clock to determine if it needs to configure the IP block as operating
at 1:1 or 1:2 clock ratio (ACR bit in SDMAARM_CONFIG). Specifying both
clocks as IMX5_CLK_SDMA results in driver incorrectly thinking that
ratio is 1:1 which results in broken SDMA funtionality. Fix the code
to specify IMX5_CLK_AHB as "ahb" clock for SDMA, to avoid detecting
incorrect clock ratio.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Angus Ainslie (Purism) <angus@akkea.ca>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 9b23e1a3e8fde76e8cc0e366ab1ed4ffb4440feb upstream.
The name of CODEC input widget to which microphone is connected through
the "Headphone" jack is "IN12" not "IN1". This fixes microphone support
on Odroid XU3.
Cc: <stable@vger.kernel.org> # v4.14+
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit b7ed69d67ff0788d8463e599dd5dd1b45c701a7e upstream.
Fix the interrupt information for the GPIO lines with a shared EINT
interrupt.
Fixes: 16d7ff2642e7 ("ARM: dts: add dts files for exynos5260 SoC")
Cc: stable@vger.kernel.org
Signed-off-by: Stuart Menefy <stuart.menefy@mathembedded.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit d040e4e8deeaa8257d6aa260e29ad69832b5d630 upstream.
The device tree compiler yells like this:
Warning (unit_address_vs_reg):
/gpu-opp-table/opp@100000000:
node has a unit name, but no reg property
Let's match the cpu opp node names and use a dash.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 41b37f4c0fa67185691bcbd30201cad566f2f0d1 upstream.
This patch fixes a spelling typo.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Fixes: cc42603de320 ("ARM: dts: imx6q-icore-rqs: Add Engicam IMX6 Q7 initial support")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 032f85c9360fb1a08385c584c2c4ed114b33c260 upstream.
Increase the reset duration to ensure correct phy functionality. The
reset duration is taken from barebox commit 52fdd510de ("ARM: dts:
pfla02: use long enough reset for ethernet phy"):
Use a longer reset time for ethernet phy Micrel KSZ9031RNX. Otherwise a
small percentage of modules have 'transmission timeouts' errors like
barebox@Phytec phyFLEX-i.MX6 Quad Carrier-Board:/ ifup eth0
warning: No MAC address set. Using random address 7e:94:4d:02:f8:f3
eth0: 1000Mbps full duplex link detected
eth0: transmission timeout
T eth0: transmission timeout
T eth0: transmission timeout
T eth0: transmission timeout
T eth0: transmission timeout
Cc: Stefan Christ <s.christ@phytec.de>
Cc: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Fixes: 3180f956668e ("ARM: dts: Phytec imx6q pfla02 and pbab01 support")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 544e784188f1dd7c797c70b213385e67d92005b6 upstream.
Raspberry pi board model B revison 2 have the hot plug detector gpio
active high (and not low as it was in the dts).
Signed-off-by: Helen Koike <helen.koike@collabora.com>
Fixes: 49ac67e0c39c ("ARM: bcm2835: Add VC4 to the device tree.")
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit e7dfb6d04e4715be1f3eb2c60d97b753fd2e4516 upstream.
The function argument for the ISC_D0 on PC9 was incorrect. According to
the documentation it should be 'C' aka 3.
Signed-off-by: David Engraf <david.engraf@sysgo.com>
Reviewed-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Fixes: 7f16cb676c00 ("ARM: at91/dt: add sama5d2 pinmux")
Cc: <stable@vger.kernel.org> # v4.4+
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 4f96dc0a3e79ec257a2b082dab3ee694ff88c317 upstream.
Correctly map the regulators used by tlv320aic3106.
Both 1.8V and 3.3V for the codec is derived from VBAT via fixed regulators.
Cc: <Stable@vger.kernel.org> # v4.14+
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 6691370646e844be98bb6558c024269791d20bd7 upstream.
Correctly map the regulators used by tlv320aic3106.
Both 1.8V and 3.3V for the codec is derived from VBAT via fixed regulators.
Cc: <Stable@vger.kernel.org> # v4.14+
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 3e3380d0675d5e20b0af067d60cb947a4348bf9b upstream.
Improve the DTS files by removing all the leading "0x" and zeros to fix
the following dtc warnings:
Warning (unit_address_format): Node /XXX unit name should not have leading "0x"
and
Warning (unit_address_format): Node /XXX unit name should not have leading 0s
Converted using the following command:
find . -type f \( -iname *.dts -o -iname *.dtsi \) -exec sed -i -e "s/@\([0-9a-fA-FxX\.;:#]+\)\s*{/@\L\1 {/g" -e "s/@0x\(.*\) {/@\1 {/g" -e "s/@0+\(.*\) {/@\1 {/g" {} +
For simplicity, two sed expressions were used to solve each warnings
separately.
To make the regex expression more robust a few other issues were resolved,
namely setting unit-address to lower case, and adding a whitespace before
the opening curly brace:
https://elinux.org/Device_Tree_Linux#Linux_conventions
This will solve as a side effect warning:
Warning (simple_bus_reg): Node /XXX@<UPPER> simple-bus unit address format error, expected "<lower>"
This is a follow up to commit 4c9847b7375a ("dt-bindings: Remove leading 0x from bindings notation")
Reported-by: David Daney <ddaney@caviumnetworks.com>
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
[vzapolskiy: fixed commit message to pass checkpatch.pl test]
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 29f0023d01f063feacfc404f0446905aee4f82ee upstream.
According to the Odroid-C1+ schematics the Ethernet TXD1 signal is
routed to GPIOH_5 and the TXD0 signal is routed to GPIOH_6.
The public S805 datasheet shows that TXD0 can be routed to DIF_2_P and
TXD1 can be routed to DIF_2_N instead.
The pin groups eth_txd0_0 (GPIOH_6) and eth_txd0_1 (DIF_2_P) are both
configured as Ethernet TXD0 and TXD1 data lines in meson8b.dtsi. At the
same time eth_txd1_0 (GPIOH_5) and eth_txd1_1 (DIF_2_N) are configured
as TXD0 and TXD1 data lines as well.
This results in a bad Ethernet receive performance. Presumably this is
due to the eth_txd0 and eth_txd1 signal being routed to the wrong pins.
As a result of that data can only be transmitted on eth_txd2 and
eth_txd3. However, I have no scope to fully confirm this assumption.
The vendor u-boot sources for Odroid-C1 use the following Ethernet
pinmux configuration:
SET_CBUS_REG_MASK(PERIPHS_PIN_MUX_6, 0x3f4f);
SET_CBUS_REG_MASK(PERIPHS_PIN_MUX_7, 0xf00000);
This translates to the following pin groups in the mainline kernel:
- register 6 bit 0: eth_rxd1 (DIF_0_P)
- register 6 bit 1: eth_rxd0 (DIF_0_N)
- register 6 bit 2: eth_rx_dv (DIF_1_P)
- register 6 bit 3: eth_rx_clk (DIF_1_N)
- register 6 bit 6: eth_tx_en (DIF_3_P)
- register 6 bit 8: eth_ref_clk (DIF_3_N)
- register 6 bit 9: eth_mdc (DIF_4_P)
- register 6 bit 10: eth_mdio_en (DIF_4_N)
- register 6 bit 11: eth_tx_clk (GPIOH_9)
- register 6 bit 12: eth_txd2 (GPIOH_8)
- register 6 bit 13: eth_txd3 (GPIOH_7)
- register 7 bit 20: eth_txd0_0 (GPIOH_6)
- register 7 bit 21: eth_txd1_0 (GPIOH_5)
- register 7 bit 22: eth_rxd3 (DIF_2_P)
- register 7 bit 23: eth_rxd2 (DIF_2_N)
Drop the eth_txd0_1 and eth_txd1_1 groups from eth_rgmii_pins to fix the
Ethernet transmit performance on Odroid-C1. Also add the eth_rxd2 and
eth_rxd3 groups so we don't rely on the bootloader to set them up.
iperf3 statistics before this change:
- transmitting from Odroid-C1: 741 Mbits/sec (0 retries)
- receiving on Odroid-C1: 199 Mbits/sec (1713 retries)
iperf3 statistics after this change:
- transmitting from Odroid-C1: 667 Mbits/sec (0 retries)
- receiving on Odroid-C1: 750 Mbits/sec (0 retries)
Fixes: b96446541d8390 ("ARM: dts: meson8b: extend ethernet controller description")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Emiliano Ingrassia <ingrassia@epigenesys.com>
Cc: Linus Lüssing <linus.luessing@c0d3.blue>
Tested-by: Emiliano Ingrassia <ingrassia@epigenesys.com>
Reviewed-by: Emiliano Ingrassia <ingrassia@epigenesys.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit a3238924a820c1d7c977b632b769f3b5690cba09 upstream.
The maximum voltage value for buck8 regulator on Odroid XU3/XU4 boards is
set too low. Increase it to the 2000mV as specified on the board schematic.
So far the board worked fine, because of the bug in the PMIC driver, which
used incorrect step value for that regulator. It interpreted the voltage
value set by the bootloader as 1225mV and kept it unchanged. The regulator
driver has been however fixed recently in the commit 56b5d4ea778c
("regulator: s2mps11: Fix steps for buck7, buck8 and LDO35"), what results
in reading the proper buck8 value and forcing it to 1500mV on boot. This
is not enough for proper board operation and results in eMMC errors during
heavy IO traffic. Increasing maximum voltage value for buck8 restores
original driver behavior and fixes eMMC issues.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Fixes: 86a2d2ac5e5d ("ARM: dts: Add dts file for Odroid XU3 board")
Fixes: 56b5d4ea778c ("regulator: s2mps11: Fix steps for buck7, buck8 and LDO35")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 6fc979179c98d2591784937d5618edc3e5cd31c1 upstream.
Commit 3b79919946cd2cf4dac47842afc9a893acec4ed7 ("ARM: dts:
armada-370-xp: update NAND node with new bindings") updated some
Marvell Armada DT description to use the new NAND controller bindings,
but did it incorrectly for a number of boards: armada-xp-gp,
armada-xp-db and armada-xp-lenovo-ix4-300d. Due to this, the NAND is
no longer detected on those platforms.
This commit fixes that by properly using the new NAND DT binding. This
commit was runtime-tested on Armada XP GP, the two other platforms are
only compile-tested.
Fixes: 3b79919946cd2 ("ARM: dts: armada-370-xp: update NAND node with new bindings")
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit a66352e005488ecb4b534ba1af58a9f671eba9b8 upstream.
Add minimal parameters needed by the Exynos CLKOUT driver to Exynos3250
PMU node. This fixes the following warning on boot:
exynos_clkout_init: failed to register clkout clock
Fixes: d19bb397e19e ("ARM: dts: exynos: Update PMU node with CLKOUT related data")
Cc: <stable@vger.kernel.org>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit ec33745bccc8f336957c751f4153421cc9ef5a54 upstream.
Commit 225da7e65a03 ("ARM: dts: add eMMC reset line for
exynos4412-odroid-common") added MMC power sequence for eMMC card of
Odroid X2/U3. It reused generic sd1_cd pin control configuration node
and only disabled pull-up. However that time the pinctrl configuration
was not applied during MMC power sequence driver initialization. This
has been changed later by commit d97a1e5d7cd2 ("mmc: pwrseq: convert to
proper platform device").
It turned out then, that the provided pinctrl configuration is not
correct, because the eMMC_RTSN line is being re-configured as 'special
function/card detect function for mmc1 controller' not the simple
'output', thus the power sequence driver doesn't really set the pin
value. This in effect broke the reboot of Odroid X2/U3 boards. Fix this
by providing separate node with eMMC_RTSN pin configuration.
Cc: <stable@vger.kernel.org>
Reported-by: Markus Reichl <m.reichl@fivetechno.de>
Suggested-by: Ulf Hansson <ulf.hansson@linaro.org>
Fixes: 225da7e65a03 ("ARM: dts: add eMMC reset line for exynos4412-odroid-common")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit ba0f4560526ba19300c07ed5a3c1df7592815dc6 upstream.
i.MX6SX has same GPT type as i.MX6DL, in GPT driver, it uses
below TIMER_OF_DECLARE, so the backward compatible should be
"fsl,imx6dl-gpt", correct it.
TIMER_OF_DECLARE(imx6sx_timer, "fsl,imx6sx-gpt", imx6dl_timer_init_dt);
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 8615f5596335db0978cea593dcd0070dc5f8b116 upstream.
After commit 89a5e15bcba87d ("gpio/mmc/of: Respect polarity in the device
tree") SD cards are not detected anymore.
The CD GPIO is "active low" on the MXIII-Plus. The MMC dt-bindings
specify: "[...] using the "cd-inverted" property means, that the CD line
is active high, i.e. it is high, when a card is inserted".
Fix the description of the SD card by marking it as GPIO_ACTIVE_LOW and
drop the "cd-inverted" property. This makes the definition consistent
with the existing dt-bindings and fixes the check whether an SD card is
inserted.
Fixes: 35ee52bea66c74 ("ARM: dts: meson8m2: add support for the Tronsmart MXIII Plus")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 3fb348e030319f20ebbde082a449d4bf8a96f2fd upstream.
After commit 89a5e15bcba87d ("gpio/mmc/of: Respect polarity in the device
tree") SD cards are not detected anymore.
The CD GPIO is "active low" on Odroid-C1. The MMC dt-bindings specify:
"[...] using the "cd-inverted" property means, that the CD line is active
high, i.e. it is high, when a card is inserted".
Fix the description of the SD card by marking it as GPIO_ACTIVE_LOW and
drop the "cd-inverted" property. This makes the definition consistent
with the existing dt-bindings and fixes the check whether an SD card is
inserted.
Fixes: e03efbce6bebf5 ("ARM: dts: meson8b-odroidc1: add microSD support")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit e35e26b26e955c53e61c154ba26b9bb15da6b858 upstream.
A long running stress test on a custom board shipping an AXG SoCs and a
Realtek RTL8211F PHY revealed that after a few hours the connection
speed would drop drastically, from ~1000Mbps to ~3Mbps. At the same time
the 'macirq' (eth0) IRQ would stop being triggered at all and as
consequence the GMAC IRQs never ACKed.
After a painful investigation the problem seemed to be due to a wrong
defined IRQ type for the GMAC IRQ that should be LEVEL_HIGH instead of
EDGE_RISING.
The change in the macirq IRQ type also solved another long standing
issue affecting this SoC/PHY where EEE was causing the network
connection to die after stressing it with iperf3 (even though much
sooner). It's now possible to remove the 'eee-broken-1000t' quirk as
well.
Fixes: 9c15795a4f96 ("ARM: dts: meson8b-odroidc1: ethernet support")
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit ef4a55b9197a8f844ea0663138e902dcce3e2f36 upstream.
We're now getting the following error:
genirq: Setting trigger mode 1 for irq 230 failed
(regmap_irq_set_type+0x0/0x15c)
cpcap-usb-phy cpcap-usb-phy.0: could not get irq dp: -524
Cc: Sebastian Reichel <sre@kernel.org>
Reported-by: Pavel Machek <pavel@ucw.cz>
Tested-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 8443e4843e1c2594bf5664e1d993a1be71d1befb upstream.
Commit a758f50f10cf ("mtd: onenand: omap2: Configure driver from DT")
started using DT specified timings for GPMC, and as a result the
OneNAND stopped working on N950/N9 as we had wrong values in the DT.
Fix by updating the values to bootloader timings that have been tested
to be working on both Nokia N950 and N9.
Fixes: a758f50f10cf ("mtd: onenand: omap2: Configure driver from DT")
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit d0243693fbf6fbd48b4efb2ba7210765983b03e3 upstream.
Commit 83a86fbb5b56 ("irqchip/gic: Loudly complain about the use of
IRQ_TYPE_NONE") started warning about incorrect dts usage for irqs.
ARM GIC only supports active-high interrupts for SPI (Shared Peripheral
Interrupts), and the Palmas PMIC by default is active-low.
Palmas PMIC allows changing the interrupt polarity using register
PALMAS_POLARITY_CTRL_INT_POLARITY, but configuring sys_nirq1 with
a pull-down and setting PALMAS_POLARITY_CTRL_INT_POLARITY made the
Palmas RTC interrupts stop working. This can be easily tested with
kernel tools rtctest.c.
Turns out the SoC inverts the sys_nirq pins for GIC as they do not go
through a peripheral device but go directly to the MPUSS wakeupgen.
I've verified this by muxing the interrupt line temporarily to gpio_wk16
instead of sys_nirq1. with a gpio, the interrupt works fine both
active-low and active-high with the SoC internal pull configured and
palmas polarity configured. But as sys_nirq1, the interrupt only works
when configured ACTIVE_LOW for palmas, and ACTIVE_HIGH for GIC.
Note that there was a similar issue earlier with tegra114 and palmas
interrupt polarity that got fixed by commit df545d1cd01a ("mfd: palmas:
Provide irq flags through DT/platform data"). However, the difference
between omap5 and tegra114 is that tegra inverts the palmas interrupt
twice, once when entering tegra PMC, and again when exiting tegra PMC
to GIC.
Let's fix the issue by adding a custom wakeupgen_irq_set_type() for
wakeupgen and invert any interrupts with wrong polarity. Let's also
warn about any non-sysnirq pins using wrong polarity. Note that we
also need to update the dts for the level as IRQ_TYPE_NONE never
has irq_set_type() called, and let's add some comments and use proper
pin nameing to avoid more confusion later on.
Cc: Belisko Marek <marek.belisko@gmail.com>
Cc: Dmitry Lifshitz <lifshitz@compulab.co.il>
Cc: "Dr. H. Nikolaus Schaller" <hns@goldelico.com>
Cc: Jon Hunter <jonathanh@nvidia.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
Cc: Santosh Shilimkar <ssantosh@kernel.org>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Thierry Reding <treding@nvidia.com>
Cc: stable@vger.kernel.org # v4.17+
Reported-by: Belisko Marek <marek.belisko@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit b5f034845e70916fd33e172fad5ad530a29c10ab upstream.
These two lines are active high, not active low. The bug was
found when we changed the kernel to respect the polarity defined
in the device tree.
Fixes: 1b90e06b1429 ("ARM: kirkwood: Use devicetree to define DNS-32[05] fan")
Cc: Jamie Lentin <jm@lentin.co.uk>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Gregory Clement <gregory.clement@bootlin.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Cc: Julien D'Ascenzio <jdascenzio@posteo.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Jamie Lentin <jm@lentin.co.uk>
Reported-by: Julien D'Ascenzio <jdascenzio@posteo.net>
Tested-by: Julien D'Ascenzio <jdascenzio@posteo.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 738a05e673435afb986b53da43befd83ad87ec3b upstream.
The vendor firmware was analyzed to get the right idea about
this flash layout. /proc/mtd contains:
dev: size erasesize name
mtd0: 01e7ff40 00020000 "rootfs"
mtd1: 01f40000 00020000 "upgrade"
mtd2: 00040000 00020000 "rgdb"
mtd3: 00020000 00020000 "nvram"
mtd4: 00040000 00020000 "RedBoot"
mtd5: 00020000 00020000 "LangPack"
mtd6: 02000000 00020000 "flash"
Here "flash" is obviously the whole device and we know "rootfs"
is a bogus hack to point to a squashfs rootfs inside of the main
"upgrade partition". We know "RedBoot" is the first 0x40000 of
the flash and the "upgrade" partition follows from 0x40000 to
0x1f8000. So we have mtd0, 1, 4 and 6 covered.
Remains:
mtd2: 00040000 00020000 "rgdb"
mtd3: 00020000 00020000 "nvram"
mtd5: 00020000 00020000 "LangPack"
Inspecting the flash at 0x1f8000 and 0x1fa000 reveals each of
these starting with "RGCFG1" so we assume 0x1f8000-1fbfff is
"rgdb" of 0x40000.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 84fb6c7feb1494ebb7d1ec8b95cfb7ada0264465 upstream.
It was noticed that unbinding and rebinding the KSZ8851 ethernet
resulted in the driver reporting "failed to read device ID" at probe.
Probing the reset line with a 'scope while repeatedly attempting to
bind the driver in a shell loop revealed that the KSZ8851 RSTN pin is
constantly held at zero, meaning the device is held in reset, and
does not respond on the SPI bus.
Experimentation with the startup delay on the regulator set to 50ms
shows that the reset is positively released after 20ms.
Schematics for this board are not available, and the traces are buried
in the inner layers of the board which makes tracing where the RSTN pin
extremely difficult. We can only guess that the RSTN pin is wired to a
reset generator chip driven off the ethernet supply, which fits the
observed behaviour.
Include this delay in the regulator startup delay - effectively
treating the reset as a "supply stable" indicator.
This can not be modelled as a delay in the KSZ8851 driver since the
reset generation is board specific - if the RSTN pin had been wired to
a GPIO, reset could be released earlier via the already provided support
in the KSZ8851 driver.
This also got confirmed by Peter Ujfalusi <peter.ujfalusi@ti.com> based
on Blaze schematics that should be very close to SDP4430:
TPS22902YFPR is used as the regulator switch (gpio48 controlled):
Convert arm boot_lock to raw The VOUT is routed to TPS3808G01DBV.
(SCH Note: Threshold set at 90%. Vsense: 0.405V).
According to the TPS3808 data sheet the RESET delay time when Ct is
open (this is the case in the schema): MIN/TYP/MAX: 12/20/28 ms.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
[tony@atomide.com: updated with notes from schematics from Peter]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 8ef86955fe59f7912a40d57ae4c6d511f0187b4d upstream.
The base aspeed-g5.dtsi already defines a '/memory@80000000' node, so
'/memory' in the board files create a duplicate node. We're probably
getting lucky that the bootloader fixes up the memory node that the
kernel ends up using. Add the unit-address so it's merged with the base
node.
Found with DT json-schema checks.
Cc: Joel Stanley <joel@jms.id.au>
Cc: Andrew Jeffery <andrew@aj.id.au>
Cc: devicetree@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-aspeed@lists.ozlabs.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 1147e05ac9fc2ef86a3691e7ca5c2db7602d81dd upstream.
Marvell keeps their MMP2 datasheet secret, but there are good clues
that TWSI2 is not on 0xd4025000 on that platform, not does it use
IRQ 58. In fact, the IRQ 58 on MMP2 seems to be a signal processor:
arch/arm/mach-mmp/irqs.h:#define IRQ_MMP2_MSP 58
I'm taking a somewhat educated guess that is probably a copy & paste
error from PXA168 or PXA910 and that the real controller in fact hides
at address 0xd4031000 and uses an interrupt line multiplexed via IRQ 17.
I'm also copying some properties from TWSI1 that were missing or
incorrect.
Tested on a OLPC XO 1.75 machine, where the RTC is on TWSI2.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Tested-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit f15096f12a4e9340168df5fdd9201aa8ed60d59e upstream.
According to bindings/regulator/fixed-regulator.txt the 'clocks' and
'clock-names' properties are not valid ones.
In order to turn on the Wifi clock the correct location for describing
the CLKO2 clock is via a mmc-pwrseq handle, so do it accordingly.
Fixes: 56354959cfec ("ARM: dts: imx: add Boundary Devices Nitrogen7 board")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit c3b9ab5db11d8098ca7674175f12ab21cdce1bbb upstream.
The Wifi chip should be clocked by a 32kHz clock coming from i.MX7D
CLKO2 output pin, so describe the pinmux and clock hierarchy in the
device tree to allow the Wifi chip to be properly clocked.
Managed to successfully test Wifi with such change. Used the standard
nvram.txt file provided by TechNexion, which selects an external 32kHz
clock for the Wifi chip by default.
Fixes: 99a52450c707 ("ARM: dts: imx7d-pico: Add Wifi support")
Suggested-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Tested-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 5f8208f557065163f9a8089ea2ea7888f9d96922 upstream.
Since commit d7c5f6863550 ("ARM: dts: sun8i: a83t: bananapi-m3: Add
AXP813 regulator nodes") my BPIM3 no longer works at gigabit speed.
With the default setting, dldo3 is regulated at 2.9v which seems
sufficient for the PHY but the aforementioned commit drops it to 2.5V
which is insufficient. Note that this behaviour is random for all BPIM3.
Some work with 2.5V, but some don't.
Finnaly, someone from Bananapi confirmed that this regulator must be set
to 3.3V.
Fixes: d7c5f6863550 ("ARM: dts: sun8i: a83t: bananapi-m3: Add AXP813
regulator nodes")
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
[wens@csie.org: Reworked commit message]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 8ac686d7dfed721102860ff2571e6b9f529ae81a upstream.
The assigned parent clocks should be normally specified in the consumer
device's DT node, this ensures respective driver always sees correct clock
settings when required.
This patch fixes regression in audio subsystem on Odroid XU3/XU4 boards
that appeared after commits:
commit 647d04f8e07a ("ASoC: samsung: i2s: Ensure the RCLK rate is properly determined")
commit 995e73e55f46 ("ASoC: samsung: i2s: Fix rclk_srcrate handling")
commit 48279c53fd1d ("ASoC: samsung: i2s: Prevent external abort on exynos5433 I2S1 access")
Without this patch the driver gets wrong clock as the I2S function clock
(op_clk) in probe() and effectively the clock which is finally assigned
from DT is not being enabled/disabled in the runtime resume/suspend ops.
Without the above listed commits the EXYNOS_I2S_BUS clock was always set
as parent of CLK_I2S_RCLK_SRC regardless of DT settings so there was no issue
with not enabled EXYNOS_SCLK_I2S.
Cc: <stable@vger.kernel.org> # 4.17.x
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit e25b6783c7b1bb79103d4617336879423f86b05e upstream.
The commit b1b8f45b3130 ("ARM: dts: bcm2837: Add missing GPIOs of Expander")
introduced a wifi power sequence. Unfortunately the polarity of the reset
GPIOs were wrong and broke the wifi support on Raspberry Pi 3 B and
later in 3 B+. This wasn't discovered before since the power sequence
takes only effect in case the relevant MMC driver is compiled as a module.
Fixes: b1b8f45b3130 ("ARM: dts: bcm2837: Add missing GPIOs of Expander")
Cc: stable@vger.kernel.org
Reported-by: Matthias Lueschner <lueschem@gmail.com>
Link: https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=911443
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 4ab7ca092c3c7ac8b16aa28eba723a8868f82f14 upstream.
The SAMA5D2 is different from SAMA5D3 and SAMA5D4, as there are two
different clocks for the peripherals in the SoC. The Static Memory
controller is connected to the divided master clock.
Unfortunately, the device tree does not correctly show this and uses the
master clock directly. This clock is then used by the code for the NAND
controller to calculate the timings for the controller, and we end up with
slow NAND Flash access.
Fix the device tree, and the performance of Flash access is improved.
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 3d8b804bc528d3720ec0c39c212af92dafaf6e84 upstream.
The interrupt on mmc3_dat1 is wrong which prevents this from
appearing in /proc/interrupts.
Fixes: ab8dd3aed011 ("ARM: DTS: Add minimal Support for Logic PD
DM3730 SOM-LV") #Kernel 4.9+
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 6809564d64ff1301d44c13334cc0e8369e825a20 upstream.
When the Torpedo was first introduced back at Kernel 4.2,
the interrupt extended flag has been set incorrectly.
It was subsequently moved, so this patch corrects Kernel
4.18+
Fixes: a38867305203 ("ARM: dts: Move move WiFi bindings to
logicpd-torpedo-37xx-devkit") # v4.18+
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit e7f4ffffa972db4820c23ff9831a6a4f3f6d8cc5 upstream.
The MMC1 is active low, not active high. For some reason,
this worked with different combination of U-Boot and kernels,
but it's supposed to be active low and is currently broken.
Fixes: cfaa856a2510 ("ARM: dts: am3517: Add pinmuxing, CD and
WP for MMC1") #kernel 4.18+
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 672e60b72bbe7aace88721db55b380b6a51fb8f9 upstream.
The Coreboot version on veyron ChromeOS devices seems to ignore
memory@0 nodes when updating the available memory and instead
inserts another memory node without the address.
This leads to 4GB systems only ever be using 2GB as the memory@0
node takes precedence. So remove the @0 for veyron devices.
Fixes: 0b639b815f15 ("ARM: dts: rockchip: Add missing unit name to memory nodes in rk3288 boards")
Cc: stable@vger.kernel.org
Reported-by: Heikki Lindholm <holin@iki.fi>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 1af6ab3bac8458fc2e92ad7bb97b62de4a1fddef upstream.
A quoted label reference doesn't expand to the node path and is taken as
a literal string. Dropping the quotes can fix this unless the baudrate
string is appended in which case we have to use the alias.
At least on VF610, the problem was masked by setting the console in
bootargs. Use the alias syntax with baudrate parameter so we can drop
setting the console in bootargs.
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
[ Upstream commit 31edaa6e7fd8143085a6a60c564447c07e76ed9f ]
Signals available on both i.MX6UL and i.MX6ULL should have the same name
because it is the case of all others common signals, it avoids to make
mistakes (use the wrong ones) and it makes writing device tree files
less complicated. For example:
imx6ul-imx6ull-board.dtsi:
...
pinctrl_uart5: uart5grp {
fsl,pins = <
MX6UL_PAD_UART5_TX_DATA__UART5_DCE_TX 0x1b0b1
MX6UL_PAD_UART5_RX_DATA__UART5_DCE_RX 0x1b0b1
>;
};
imx6ul-board.dts:
#include <imx6ul.dtsi>
#include <imx6ul-imx6ull-board.dtsi>
...
imx6ull-board.dts:
#include <imx6ull.dtsi>
#include <imx6ul-imx6ull-board.dtsi>
...
Without this patch, the imx6ull-board.dtb will use
MX6UL_PAD_UART5_RX_DATA__UART5_DCE_RX instead of
MX6ULL_PAD_UART5_RX_DATA__UART5_DCE_RX and the uart5 will be
misconfigured.
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ce3bf934f919a7d675c5b7fa4cc233ded9c6256e upstream.
The address in the SDRAM node was incorrect. Fix this to agree with the
correct address and to match the reg definition block.
Cc: stable@vger.kernel.org
Fixes: 54b4a8f57848b("arm: socfpga: dts: Add Arria10 SDRAM EDAC DTS support")
Signed-off-by: Thor Thayer <thor.thayer@linux.intel.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6d0af44a82be87c13f2320821e9fbb8b8cf5a56f upstream.
Bit positions of PCIE_SS1_AXI2OCP_LEGACY_MODE_ENABLE and
PCIE_SS1_AXI2OCP_LEGACY_MODE_ENABLE in CTRL_CORE_SMA_SW_7 are
incorrectly documented in the TRM. In fact, the bit positions are
swapped. Update the DT bindings for PCIe EP to reflect the same.
Fixes: d23f3839fe97 ("ARM: dts: DRA7: Add pcie1 dt node for EP mode")
Cc: stable@vger.kernel.org
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
Krzysztof Kozlowski
Andrey Smirnov
Sylwester Nawrocki
Stuart Menefy
Douglas Anderson
Masanari Iida
Marco Felsch
Helen Koike
David Engraf
Peter Ujfalusi
Mathieu Malaterre
Martin Blumenstingl
Marek Szyprowski
Thomas Petazzoni
Anson Huang
Carlo Caione
Tony Lindgren
Aaro Koskinen
Linus Walleij
Russell King - ARM Linux
Rob Herring
Lubomir Rintel
Fabio Estevam
Corentin Labbe
Stefan Wahren
Romain Izard
Adam Ford
Heiko Stuebner
Sébastien Szymanski
Thor Thayer
Vignesh R