| Age | Commit message (Collapse) | Author |
|---|
|
The DB8500 exists in an enhanced variant named DB8520
for some machines. To clearly distinguish between the
different machines, create an explicit db8500.dtsi
and move the operating points (only known difference so
far) to that file, so we can add an explicit db8520.dtsi
after this.
Cc: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20191126124738.77690-1-linus.walleij@linaro.org
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The Ux500 device tree uses "arm,rtc-pl031" as compatible for PL031.
All other boards in Linux describe it using "arm,pl031" instead.
This works because the compatible is not actually used in Linux:
AMBA devices get probed based on "arm,primecell" and their peripheral ID.
Nevertheless, some other projects (e.g. U-Boot) rely on the compatible
to probe the device with the correct driver. Those will look for
"arm,pl031" instead of "arm,rtc-pl031", preventing the RTC from being
probed.
Change it to "arm,pl031" to match all other boards.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20191124205110.48031-1-stephan@gerhold.net
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The "soc" node in the Ux500 device tree does not need any special
handling - it is just a simple I/O bus that can be accessed without
additional configuration.
Therefore we can additionally describe it as compatible with "simple-bus".
This can be used by platforms to probe devices under the soc node without
special handling for our custom "stericsson,db8500" compatible
(e.g. in U-Boot).
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20191124195728.32226-1-stephan@gerhold.net
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
ux500_serial{0,1,2} are the only labels with ux500_ prefix in
ste-dbx5x0.dtsi, the other labels (gpio0, msp, ...) do not use
any prefix. Remove it for consistency.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20191125170428.76069-4-stephan@gerhold.net
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Now that we have aliases for I2C and SPI in ste-dbx5x0.dtsi,
it does not make much sense to keep only the aliases for UART
separately in each board device tree.
Considering that all boards set the same aliases for the serial
ports there is no reason to keep them separated either.
Move them to ste-dbx5x0.dtsi and remove the aliases from the
board-specific device tree parts.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20191125170428.76069-3-stephan@gerhold.net
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Now that we disable the I2C/SPI buses by default, is is even more
important to assign aliases to the I2C/SPI device nodes.
Otherwise, enabling/disabling one of them will potentially change
all device IDs, e.g. i2c2 will be named i2c-0 if it is the only
enabled I2C bus.
Add aliases for the I2C and SPI buses to avoid this.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20191125170428.76069-2-stephan@gerhold.net
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
At the moment, all 5 I2C and 6 SPI buses are probed and exposed
to user-space by default - even if they are not muxed to any pins
on the board. This means that user-space sees an I2C/SPI bus that
cannot be actually used properly.
In some cases this was used to put the corresponding pins into
a low power sleep mode - but even then the pins first need to be
configured by the board-specific device tree part.
Avoid exposing unconfigured devices to user-space by disabling
the I2C/SPI buses by default. Enable them in the board device trees
when needed.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20191125170428.76069-1-stephan@gerhold.net
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This fixes up the default ux500 CPU thermal zone:
- Set polling delay to 0 and explain why
- Set passive polling delay to 250
- Remove restrictions from the CPU cooling device,
we should use all cpufreq steps to cool down if
needed.
Link: https://lore.kernel.org/r/20191001074628.8122-1-linus.walleij@linaro.org
Fixes: b786a05f6ce4 ("ARM: dts: ux500: Update thermal zone")
Suggested-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
After moving the DB8500 thermal driver to use device tree
we define the default thermal zone for the Ux500 in the
device tree replacing the oldstyle hardcoded trigger
points.
This default thermal zone utilizes the cpufreq driver
(using the generic OF cpufreq back-end) as a passive
cooling device, and defines a critical trip point when
the temperature goes above 85 degrees celsius which will
(hopefully) make the system shut down if the temperature
cannot be controlled.
This default policy can later be augmented for specific
subdevices if these have tighter temperature conditions.
After this patch we get:
/sys/class/thermal/thermal_zone0 (CPU thermal zone)
This reports the rough temperature and trip points
from the thermal zone in the device tree.
By executing two yes > /dev/null & jobs fully utilizing
the two CPU cores we can notice the temperature climbing
in the thermal zone in response and falling when we kill
the jobs.
/syc/class/thermal/cooling_device0 (cpufreq cooling)
this reports all 4 available cpufreq frequencies as
states.
Suggested-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Some Ux500 devices use the newer AB8505 PMIC instead of AB8500.
Although they are very similar, there are subtle differences
like the number of regulators or the available GPIO pins.
At the moment, ste-dbx5x0.dtsi always configures the AB8500 PMIC.
To support devices with AB8505, it is necessary to split the
AB8500-specific parts into a separate .dtsi file. Boards can then
select the PMIC by including either ste-ab8500.dtsi or ste-ab8505.dtsi.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The thermal driver for the DB8500 was never properly converted
to device tree, the node should definitely be activated for
all board variants so move this down into the main SoC
DTSI, and default on.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
CoreSight DT bindings have been updated, thus the old compatible strings
are obsolete and the drivers will report warning if DTS uses these
obsolete strings.
This patch switches to the new bindings for CoreSight dynamic funnel and
static replicator, so can dismiss warning during initialisation.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Based on 1 normalized pattern(s):
the code contained herein is licensed under the gnu general public
license you may obtain a copy of the gnu general public license
version 2 or later at the following locations http www opensource
org licenses gpl license html http www gnu org copyleft gpl html
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 161 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.383790741@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This adds and updates the device tree nodes for the MCDE
display controller and connects the Samsung display to
the TVK1281618 user interface board (UIB) so we get
nicely working graphics on this reference design.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This adds the Mali-400 block, also known as SGA500 or the
Smart Graphics Adapter, to the DBx500 DTS file. All
resources and bindings are already in place so this just
works.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
We need to distribute out the responsibilities of the PRCMU
registers instead of having one big lump handling everything.
By making it syscon compatible, we can start grabbing the
register map elsewhere when needed.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Switch to the new coresight bindings
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
SPI controller nodes should be named 'spi' rather than 'ssp'. Fixing the
name enables dtc SPI bus checks.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
By removing the reference to skeleton.dtsi, defining chosen {}
and proper memory nodes we get warning-free device trees for
the Ux500.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The unit address of the Cortex-A9 SCU device node contains one zero too
many. Remove it.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This adds the operating points to the Ux500 device tree and
deletes the old special-purpose cpufreq node, as we can now
use the generic DT cpufreq driver.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
|
|
The best place to register the CPU cooling device is from the cpufreq
driver as we would know if all the resources are already available or
not. That's what is done for the cpufreq-dt.c driver as well.
The cpu-cooling driver for dbx500 platform was just (un)registering
with the thermal framework and that can be handled easily by the cpufreq
driver as well and in proper sequence as well.
Get rid of the cooling driver and its its users and manage everything
from the cpufreq driver instead.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
This adds the AB8500 clocks to the device tree using the new
bindings from the clk subsystem, making audio work again.
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
This clock has been missing since some early stages of device tree
conversion. Adding the right clocks to the device tree makes USB
work again.
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Move the compatible string "stericsson,ab8500" from the board
definitions into the main node in the chipset file where it
belongs.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Use the <dt-bindings/interrupt-controller/arm-gic.h> header for
generating the flags for the first cell of the interrupt
definitions.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Use the <dt-bindings/gpio/gpio.h> header instead of using
hardcoded values for the GPIO flags. Eradicate the totally
bogus "0x4" flag used and set that to GPIO_ACTIVE_HIGH as is
proper, switch the inverted card detect on the Snowball to
flag using GPIO_ACTIVE_LOW instead of using the MMC-specific
inversion flag.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The regulator-compatible property from the regulator DT binding was
deprecated and the correct approach is to use the node's name.
This patch has no functional changes since the values of the node's
name and the regulator-compatible match for all the regulators.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v4.3 development
cycle.
Like with GPIO it's a lot of stuff. If my subsystems are any sign of
the overall tempo of the kernel v4.3 will be a gigantic diff.
[ It looks like 4.3 is calmer than 4.2 in most other subsystems, but
we'll see - Linus ]
Core changes:
- It is possible configure groups in debugfs.
- Consolidation of chained IRQ handler install/remove replacing all
call sites where irq_set_handler_data() and
irq_set_chained_handler() were done in succession with a combined
call to irq_set_chained_handler_and_data(). This series was
created by Thomas Gleixner after the problem was observed by
Russell King.
- Tglx also made another series of patches switching
__irq_set_handler_locked() for irq_set_handler_locked() which is
way cleaner.
- Tglx also wrote a good bunch of patches to make use of
irq_desc_get_xxx() accessors and avoid looking up irq_descs from
IRQ numbers. The goal is to get rid of the irq number from the
handlers in the IRQ flow which is nice.
Driver feature enhancements:
- Power management support for the SiRF SoC Atlas 7.
- Power down support for the Qualcomm driver.
- Intel Cherryview and Baytrail: switch drivers to use raw spinlocks
in IRQ handlers to play nice with the realtime patch set.
- Rework and new modes handling for Qualcomm SPMI-MPP.
- Pinconf power source config for SH PFC.
New drivers and subdrivers:
- A new driver for Conexant Digicolor CX92755.
- A new driver for UniPhier PH1-LD4, PH1-Pro4, PH1-sLD8, PH1-Pro5,
ProXtream2 and PH1-LD6b SoC pin control support.
- Reverse-egineered the S/PDIF settings for the Allwinner sun4i
driver.
- Support for Qualcomm Technologies QDF2xxx ARM64 SoCs
- A new Freescale i.mx6ul subdriver.
Cleanup:
- Remove platform data support in a number of SH PFC subdrivers"
* tag 'pinctrl-v4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (95 commits)
pinctrl: at91: fix null pointer dereference
pinctrl: mediatek: Implement wake handler and suspend resume
pinctrl: mediatek: Fix multiple registration issue.
pinctrl: sh-pfc: r8a7794: add USB pin groups
pinctrl: at91: Use generic irq_{request,release}_resources()
pinctrl: cherryview: Use raw_spinlock for locking
pinctrl: baytrail: Use raw_spinlock for locking
pinctrl: imx6ul: Remove .owner field
pinctrl: zynq: Fix typos in smc0_nand_grp and smc0_nor_grp
pinctrl: sh-pfc: Implement pinconf power-source param for voltage switching
clk: rockchip: add pclk_pd_pmu to the list of rk3288 critical clocks
pinctrl: sun4i: add spdif to pin description.
pinctrl: atlas7: clear ugly branch statements for pull and drivestrength
pinctrl: baytrail: Serialize all register access
pinctrl: baytrail: Drop FSF mailing address
pinctrl: rockchip: only enable gpio clock when it setting
pinctrl/mediatek: fix spelling mistake in dev_err error message
pinctrl: cherryview: Serialize all register access
pinctrl: UniPhier: PH1-Pro5: add I2C ch6 pin-mux setting
pinctrl: nomadik: reflect current input value
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Michael Turquette:
"The clk framework changes for 4.3 are mostly updates to existing
drivers and the addition of new clock drivers. Stephen Boyd has also
done a lot of subsystem-wide driver clean-ups (thanks!). There are
also fixes to the framework core and changes to better split clock
provider drivers from clock consumer drivers"
* tag 'clk-for-linus-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (227 commits)
clk: s5pv210: add missing call to samsung_clk_of_add_provider()
clk: pistachio: correct critical clock list
clk: pistachio: Fix PLL rate calculation in integer mode
clk: pistachio: Fix override of clk-pll settings from boot loader
clk: pistachio: Fix 32bit integer overflows
clk: tegra: Fix some static checker problems
clk: qcom: Fix MSM8916 prng clock enable bit
clk: Add missing header for 'bool' definition to clk-conf.h
drivers/clk: appropriate __init annotation for const data
clk: rockchip: register pll mux before pll itself
clk: add bindings for the Ux500 clocks
clk/ARM: move Ux500 PRCC bases to the device tree
clk: remove duplicated code with __clk_set_parent_after
clk: Convert __clk_get_name(hw->clk) to clk_hw_get_name(hw)
clk: Constify clk_hw argument to provider APIs
clk: Hi6220: add stub clock driver
dt-bindings: clk: Hi6220: Document stub clock driver
dt-bindings: arm: Hi6220: add doc for SRAM controller
clk: atlas7: fix pll missed divide NR in fraction mode
clk: atlas7: fix bit field and its root clk for coresight_tpiu
...
|
|
The base addresses for the Ux500 PRCC controllers are hardcoded,
let's move them to the clock node in the device tree and delete
the constants.
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
The "cpus" node cannot be inside the "soc" node, while this
works for the CoreSight blocks, the early boot code will look
for "cpus" directly under the root node, so this is a hard
convention. So move the CPU nodes.
Augment the "reg" property to match what is actually in the
hardware: 0x300 and 0x301 respectively.
Then add an SMP enablement type to be used by the SMP init
code, "ste,dbx500-smp".
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
This gets the GPIO ranges out of the driver and into the device
tree where they belong. Standard DT bindings already exist for
this. Since no systems with this are deployed we can just augment
all device trees and the drivers at the same time and simplify
the world.
This also defines the array of GPIO chips related to the pin
controller.
Cc: arm@kernel.org
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This enumerates the PL011 serial ports on the Ux500. This is
necessary to do if we want to remove one of the serial ports,
since userspace depends on console to be present on ttyAMA2
and we must not break userspace.
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
The Ux500 SOCs have a special backup RAM that needs to be
defined in the device tree.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The Ux500 like other Cortex-A9 SoC's has a Snoop Control
Unit (SCU) and a Watchdog in the same address range as
the local timers. Add these to the SoC device tree.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into next/dt
Merge "Ux500 Device Tree changes for the v4.2 series" form Linus Walleij:
Define CPU topology, connect that with CoreSight blocks,
add sensor information to DT boards.
* tag 'ux500-v4.2-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: ux500: add the sensors to the STUIB board
ARM: ux500: assign the sensor trigger IRQs
ARM: ux500: fix lsm303dlh magnetometer compat string
ARM: ux500: add CoreSight blocks to DTS file
ARM: ux500: define CPU topology
|
|
This registers all the CoreSight blocks on the DB8500 SoC:
each core has a PTM (v1.0, r1p0-00rel0) connected, both connected
to a funnel (DK-TM908-r0p1-00rel0) which in turn connects to a
replicator (DM-TM909-r0p1-00rel0). The replicator has two outputs,
port 0 to a TPIU interface and port 1 to an ETB
(DK-TM907-r0p3-00rel0). The CoreSight blocks are all clocked by
the APEATCLK from the PRCMU and their AHB interconnect is clocked
from a separate clock called APETRACECLK.
The SoC also has a CTI/CTM block which can be added later as we
have upstream support in the CoreSight subsystem.
Acked-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The CPU topology is unspecified for Ux500 but will be needed
for things like CoreSight. Let's just add it.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The GPIO regulator for the SD-card isn't a ux500 SOC configuration, but
instead it's specific to the board. Move the definition of it, into the
board DTSs.
Fixes: c94a4ab7af3f ("ARM: ux500: Disable the MMCI gpio-regulator by default")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The i2c-nomadik driver handle these devices properly from a runtime PM
perspective. Therefore, let's add them into VAPE PM domain for ux500.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The spi-pl022 driver handle these devices properly from a runtime PM
perspective. Therefore, let's add them into VAPE PM domain for ux500.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The mmci driver handle these devices properly from a runtime PM
perspective, including register context save/restore. Therefore let's
add them into VAPE PM domain for ux500.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add a DT node for the ux500 PM domains. Follow the DT semantics of the
generic PM domain.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This adds some missing DMA channel information to the disabled
MMC/SD/SDIO blocks number 3 and 5, and notes that the assignment
of MSP channels vary with ASIC variant.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
As noted in recent discussions the name of the core clock for
the PL022 derived SPI blocks is erroneously named in the
Ux500 device trees. The kernel doesn't currently use the name,
but may do so soon so let use rename all these clocks in
accordance with the name given in the PL022 TRM (ARM DDI 0194G).
Reviewed-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
As we need to connect resources such as pin mappings and clocks
when deleting board files, we create a MCDE node even though there
is no driver for it. As it is only using standard bindings right
now, this does not matter much. When a proper driver is written
for the MCDE, it can augment this node with custom properties.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This adds the SSP and SPI blocks to the device tree and makes
them active. Only this way can their clocks be properly gated
off at boot.
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
Linus Walleij
Stephan Gerhold
Leo Yan
Thomas Gleixner
Suzuki K Poulose
Rob Herring
Geert Uytterhoeven
Rafael J. Wysocki
Viresh Kumar
Javier Martinez Canillas
Linus Torvalds
Arnd Bergmann
Ulf Hansson
Lee Jones