| Age | Commit message (Collapse) | Author |
|---|
|
commit 7007f2eca0f258710899ca486da00546d03db0ed upstream.
USB_C_DET pin shouldn't be in ethernet group.
Creating a separate group allows one to use this pin
as an USB ID pin.
Fixes: b326629f25b7 ("ARM: dts: imx7: add Toradex Colibri iMX7S/iMX7D suppor")
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 03d655ff251c8296cd887055e470796eb1e47e47 upstream.
Prepare FlexCAN use on SODIMM 55/63 178/188. Those SODIMM pins are
compatible for CAN bus use with several modules from the Colibri
family.
Add Better drivestrength and also add flexcan2.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 2773fe1d31c42ffae2a9cb9a6055d99dd86e2fee upstream.
SD/MMC on Colibri iMX7S/D modules successfully support
200Mhz frequency in HS200 mode.
Removing the unnecessary max-frequency limit significantly
increases the performance:
== before fix ====
root@colibri-imx7-emmc:~# hdparm -t /dev/mmcblk0
/dev/mmcblk0:
Timing buffered disk reads: 252 MB in 3.02 seconds = 83.54 MB/sec
==================
=== after fix ====
root@colibri-imx7-emmc:~# hdparm -t /dev/mmcblk0
/dev/mmcblk0:
Timing buffered disk reads: 408 MB in 3.00 seconds = 135.94 MB/sec
==================
Fixes: f928a4a377e4 ("ARM: dts: imx7: add Toradex Colibri iMX7D 1GB (eMMC) support")
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
[ Upstream commit a95fbda08ee20cd063ce5826e0df95a2c22ea8c5 ]
Force HS200 by masking bit 63 of the SDHCI capability register.
The i.MX ESDHC driver uses SDHCI_QUIRK2_CAPS_BIT63_FOR_HS400. With
that the stack checks bit 63 to descide whether HS400 is available.
Using sdhci-caps-mask allows to mask bit 63. The stack then selects
HS200 as operating mode.
This prevents rare communication errors with minimal effect on
performance:
sdhci-esdhc-imx 30b60000.usdhc: warning! HS400 strobe DLL
status REF not lock!
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
Add support for the Computer on Module Colibri iMX7D 1GB along
with the Colibri Evaluation Board device trees. Follow the usual
hierarchic include model, maintaining shared configuration in
imx7-colibri.dtsi and imx7-colibri-eval-v3.dtsi respectively.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The Colibri Evaluation Carrier Board provides a MCP2515 CAN
controller connected via SPI. Note that the i.MX 7 provides
an internal CAN controller which is much better suited for CAN
operations. Using the MCP2515 with a Colibri iMX7 module is
mainly useful to test the SPI interface.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The Colibri standard defines SODIMM 71 as backlight enable
GPIO. Assign the GPIO to the backlight node in the module
level device tree.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The usdhc1 controller instance is used to provide the default
SD/MMC capabilities of the Colibri standard. The IO pins are
supplied to the SoC on the module whereas the SD-card is powered
by the Carrier Board supply.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Specify CPU supply using the "cpu-supply" property instead of
the invalid "arm-supply" property.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
All Colibri iMX7 SKUs use either single-die NAND or eMMC, hence
NAND_CE1 is not used on the module and can be used as a GPIO by
carrier boards.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Use pull-ups instead of pull-downs for the pins which are already
pulled-up externally.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The Colibri pins PWM<A> and <D> are multiplexed on the module, make
sure the secondary SoC pin is not active.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The Colibri default which enables USB Host power is not necessarily
tied to the OTG2 controller, some carrier board use the pin to
control USB power for both controllers. Hence name the pinctrl
group more generic.
Also move the regulator to the generic eval-v3 device tree since
the regulator is always on the carrier board. In the Colibri iMX7S
case the regulator is just not used. This allows to reuse the
regulator in a upcoming SKU Colibri iMX7D 1GB with eMMC.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Fix dtc warnings for 'simple_bus_reg' due to leading 0s. Converted using
the following command:
perl -p -i -e 's/\@0+([0-9a-f])/\@$1/g' `find arch/arm/boot/dts -type -f -name '*.dts*'
Dropped changes to ARM, Ltd. boards LED nodes and manually fixed up some
occurrences of uppercase hex.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The Colibri iMX7 modules come with 512MB on-module SLC NAND flash
populated. Make use of it by enabling the GPMI controller.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The PWM driver has now capability to specify the PWM polarity
which is e.g. for backlight control. Allow to make use of PWM
polarity by specifying pwm-cells to be 3 in the base dt.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The ADC is directly supplied by the PMIC 1.8V rail, remove the
superfluous fixed regulator.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The regulator-always-on property on the Ethernet rail prevents Linux
from disabling the rail when Ethernet is shut down (suspend or simply
link down). With this change the regulator framework will disable the
rail when the Ethernet PHY is not used, saving power especially on
carrier board not using Ethernet.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Fix wrong voltage of PWR_EN_+V3.3 rail. The error had no noticeable
effect since no consumer explicitly requested a specific voltage.
Also use round voltages as it is common in other device trees.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The i.MX7 has two iomux controllers. the iomuxc and the iomuxc_lpsr.
In a board dts we have to make sure that both controllers are supplied
with the correct pins. It's way too easy to do this wrong since only
a look into the reference manual can reveal which pins belong to which
controller. To make this clearer add "LPSR" to the pin names which
belong to the LPSR controller.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add audio support via on module I2S SGTL5000 codec.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Colibri modules need to be powered using the power pins 3V3 and
AVDD_AUDIO. Add fixed regulators which represent this power rails.
Potentially, those power rails could be switched on a carrier
board. A carrier board device tree could add a own regulator with
a GPIO, and reference that regulator in a vin-supply property of
those new module level system regulators. This also synchronize
the name of the +3.3V regulator with the one used in the Colibri
VF50/VF61 device tree.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Move SD-card definition to module level. While at it, also disable
write-protect since the Colibri standard does not define a pin for
SD-Card write-protection.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add support for the Computer on Module Colibri iMX7S/iMX7D along
with the development/evaluation carrier board device trees. Follow
the usual hierarchic include model, maintaining shared configuration
in imx7-colibri.dtsi and imx7-colibri-eval-v3.dtsi respectively.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
Oleksandr Suvorov
Philippe Schenker
Stefan Agner
Stefan Agner
Rob Herring
Sascha Hauer