| Age | Commit message (Collapse) | Author |
|---|
|
Fix the following warnings from dtc by adding the unit name to memory
nodes:
Warning (unit_address_vs_reg): Node /memory has a reg or ranges property, but no unit name
Converted using the following command:
perl -p0777i -e 's/memory \{\n\t\treg = \<0x+([0-9a-f])/memory\@$1$\0000000 \{\n\t\treg = <0x$1/m' `find ./arch/arm/boot/dts -name "imx*"`
The files below were manually fixed:
-imx1-ads.dts
-imx1-apf9328.dts
-imx6q-pistachio.dts
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Fix dtc warnings for 'simple_bus_reg' due to leading 0s. Converted using
the following command:
perl -p -i -e 's/\@0+([0-9a-f])/\@$1/g' `find arch/arm/boot/dts -type -f -name '*.dts*'
Dropped changes to ARM, Ltd. boards LED nodes and manually fixed up some
occurrences of uppercase hex.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Several dts files set a bit in the SPEED field for pads
RGMII_{R,T}{XC,D0,D1,D2,D3,X_CTL}, but that doesn't exist. Writing there
doesn't have an effect and the bit reads as zero.
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
According to Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt the
polarity of "reset-gpio" is assumed to be active-low unless a separate
property "reset-gpio-active-high" is available. So replace the inconsistent
polarity description to make the correct active-low reset behavior more
obvious.
Signed-off-by: Soeren Moch <smoch@web.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Using "IMX6QDL_CLK_CKO" for the clock is easier to read instead of
the hardcoded clock number.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
According to Documentation/devicetree/bindings/net/fsl-fec.txt the polarity
of "phy-reset-gpios" is assumed to be active-low unless a separate property
"phy-reset-active-high" is available. So replace the inconsistent polarity
description to make the correct active-low reset behavior more obvious.
Signed-off-by: Soeren Moch <smoch@web.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Signed-off-by: Soeren Moch <smoch@web.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Remove the following unnecessary iomuxc container nodes:
imx6q-tbs2910
gpio_fan
gpio_leds
Sort the pinctrl nodes alphabetically.
Signed-off-by: Soeren Moch <smoch@web.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Avoid the following warnings (example for usdhc2):
/soc/aips-bus@02100000/usdhc@02194000: voltage-ranges unspecified
sdhci-esdhc-imx 2194000.usdhc: could not get ultra high speed state,
work on normal mode
sdhci-esdhc-imx 2194000.usdhc: No vqmmc regulator found
Signed-off-by: Soeren Moch <smoch@web.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Configure SATA PHY transmit level, boost, attenuation and equalizer
parameters for long wire connections. TBS2910 contains a standard SATA
connector, so devices are typically connected with (longer) SATA cables.
And explicitly configuring these parameters avoids complaints about
"not specified" values in boot messages.
Signed-off-by: Soeren Moch <smoch@web.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
cd-gpios polarity should be changed to GPIO_ACTIVE_LOW and wp-gpios
should be changed to GPIO_ACTIVE_HIGH.
Otherwise, the SD may not work properly due to wrong polarity inversion
specified in DT after switch to common parsing function mmc_of_parse().
Signed-off-by: Dong Aisheng <aisheng.dong@freescale.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
This patch enables snvs-poweroff for TBS2910 boards.
Signed-off-by: Soeren Moch <smoch@web.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
imx6q-tbs2910 board uses sgtl5000 codec and the machine file (imx-sgtl5000)
already sets SSI in slave mode and codec in master mode, so there is no need
for having this property.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Soeren Moch <smoch@web.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
TBS2910 is a i.MX6Q based board. For additional details refer to
http://www.tbsdtv.com/products/tbs2910-matrix-arm-mini-pc.html
Signed-off-by: Soeren Moch <smoch@web.de>
Reviewed-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
Marco Franchi
Rob Herring
Uwe Kleine-König
Soeren Moch
Fabio Estevam
Dong Aisheng
Fabio Estevam