Age | Commit message (Collapse) | Author |
|
[ Upstream commit 44ad8207806973f4e4f7d870fff36cc01f494250 ]
Both Luxul's XAP devices (XAP-810 and XAP-1440) are access points that
use a non-default design. They don't include switch but have a single
Ethernet port and BCM54210E PHY connected to the Ethernet controller's
MDIO bus.
Support for those devices regressed due to two changes:
1. Describing MDIO bus with switch
After commit 9fb90ae6cae7 ("ARM: dts: BCM53573: Describe on-SoC BCM53125
rev 4 switch") Linux stopped probing for MDIO devices.
2. Dropping hardcoded BCM54210E delays
In commit fea7fda7f50a ("net: phy: broadcom: Fix RGMII delays
configuration for BCM54210E") support for other PHY modes was added but
that requires a proper "phy-mode" value in DT.
Both above changes are correct (they don't need to be reverted or
anything) but they need this fix for DT data to be correct and for Linux
to work properly.
Fixes: 9fb90ae6cae7 ("ARM: dts: BCM53573: Describe on-SoC BCM53125 rev 4 switch")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Link: https://lore.kernel.org/r/20230713111145.14864-1-zajec5@gmail.com
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit be7e1e5b0f67c58ec4be0a54db23b6a4fa6e2116 ]
There is no such trigger documented or implemented in Linux. It was a
copy & paste mistake.
This fixes:
arch/arm/boot/dts/broadcom/bcm47189-luxul-xap-1440.dtb: leds: led-wlan:linux,default-trigger: 'oneOf' conditional failed, one must be fixed:
'default-off' is not one of ['backlight', 'default-on', 'heartbeat', 'disk-activity', 'disk-read', 'disk-write', 'timer', 'pattern', 'audio-micmute', 'audio-mute', 'bluetooth-power', 'flash', 'kbd-capslock', 'mtd', 'nand-disk', 'none', 'torch', 'usb-gadget', 'usb-host', 'usbport']
'default-off' does not match '^cpu[0-9]*$'
'default-off' does not match '^hci[0-9]+-power$'
'default-off' does not match '^mmc[0-9]+$'
'default-off' does not match '^phy[0-9]+tx$'
From schema: Documentation/devicetree/bindings/leds/leds-gpio.yaml
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Link: https://lore.kernel.org/r/20230707114004.2740-1-zajec5@gmail.com
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
Fix the the unit_address_vs_reg warnings and unnecessary
\#address-cells/#size-cells without "ranges" or child "reg" property
warnings.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
https://github.com/Broadcom/stblinux into arm/dt
This pull request contains Broadcom ARM-based SoCs Device Tree updates
for 5.1, please pull the following:
- Dan relicenses the Luxul DTS files to GPL 2.0+/MIT
- Hao adds support for the Phicomm K3 which is a BCM4709 SoC with dual
BCM4366 radio
- Stefan adds support for the Raspberry Pi A+: binding and DTS files. He
also provides a bunch of DTC warning fixes for the different RPi DTS(i)
files and adds support for missing GPIO lines on RPi 2/3
* tag 'arm-soc/for-5.1/devicetree' of https://github.com/Broadcom/stblinux:
ARM: dts: bcm2835-rpi-zero-w: Drop unnecessary pinctrl
ARM: dts: bcm283x: Add missing GPIO line names
ARM: dts: bcm2837-rpi-3-b-plus: Clarify label for STATUS_LED
ARM: dts: bcm2837-rpi-3-b: Use consistent label for HDMI hotplug
ARM: dts: bcm2835: Fix labels for GPIO 0,1
ARM: dts: bcm2835-rpi: Drop unnecessary #address-cells/#size-cells
ARM: dts: bcm283x: Fix DTC warning for memory node
ARM: dts: add Raspberry Pi 3 A+
dt-bindings: bcm: Add Raspberry Pi 3 A+
ARM: dts: BCM5301X: Add basic DT for Phicomm K3
ARM: dts: BCM53573: Relicense Luxul files to the GPL 2.0+ / MIT
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Remove the usage of skeleton.dtsi in the remaining dts files. It was
deprecated since commit 9c0da3cc61f1 ("ARM: dts: explicitly mark
skeleton.dtsi as deprecated"). This will make adding a unit-address to
memory nodes easier.
The main tricky part to removing skeleton.dtsi is we could end up with
no /memory node at all when a bootloader depends on one being present. I
hacked up dtc to check for this condition.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Antoine Tenart <antoine.tenart@bootlin.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Tested-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
This matches licensing used by other BCM53573 files and BCM5301X.
Signed-off-by: Dan Haab <dan.haab@luxul.com>
Acked-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
This is BCM53573 WiSoC based outdoor access point with an extra BCM43217
chipset used for 2.4 GHz.
Signed-off-by: Dan Haab <dhaab@luxul.com>
Acked-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|