| Age | Commit message (Collapse) | Author |
|---|
|
[ Upstream commit 81cc0877840f72210e809bbedd6346d686560fc1 ]
PERST# line in the PCIE connector is driven by the host mode and not
EP mode. The gpios property here is used for driving the PERST# line.
Remove gpios property from all endpoint device tree nodes.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 0c4eb2a6b3c6b0facd0a3bccda5db22e7b3b6f96 upstream.
commit d23f3839fe97d8dce03d ("ARM: dts: DRA7: Add pcie1 dt node for
EP mode") while adding the dt node for EP mode for DRA7 platform,
added rc node for am571x-idk and populated gpios property with
"gpio3 23". However the GPIO_PCIE_SWRST line is actually connected
to "gpio5 18". Fix it here. (The patch adding "gpio3 23" was tested
with another am57x board in EP mode which doesn't rely on reset from
host).
Cc: stable <stable@vger.kernel.org> # 4.14+
Fixes: d23f3839fe97d8dce03d ("ARM: dts: DRA7: Add pcie1 dt node for EP mode")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
|
|
If UHS speed modes are enabled, a compatible SD card switches down to
1.8V during enumeration. If after this a software reboot/crash takes
place and on-chip ROM tries to enumerate the SD card, the difference in
IO voltages (host @ 3.3V and card @ 1.8V) may end up damaging the card.
The fix for this is to have support for power cycling the card in
hardware (with a PORz/soft-reset line causing a power cycle of the
card). Because the beaglebone X15 (rev A,B and C), am57xx-idks and
am57xx-evms don't have this capability, disable voltage switching for
these boards.
The major effect of this is that the maximum supported speed
mode is now high speed(50 MHz) down from SDR104(200 MHz).
commit 88a748419b84 ("ARM: dts: am57xx-idk: Remove support for voltage
switching for SD card") did this only for idk boards. Do it for all
affected boards.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
AM5 and DRA7 SoC families have different set of modules
in them so the SoC sepecific dtsi files need to be separated.
e.g. Some of the major differences between AM576 and DRA76
DRA76x AM576x
USB3 x
USB4 x
ATL x
VCP x
MLB x
ISS x
PRU-ICSS1 x
PRU-ICSS2 x
This patch only deals with disabling USB3, USB4 and ATL for
AM57 variants.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
am574x-idk has no cpu vdd-supply at the moment. Hence hook smps12
regulator as cpu vdd-supply in am57xx-idk-common as the same regulator
feeds on to cpu on am571/2/4-idks. So remove all the individual
instances and place that in common place.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The SN65HVS882 load trigger is attached to GPIO2_23 on the AM571x IDK.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
AM571x-IDK rev 1.2A has tricolor RGB LEDs that can be controlled using
GPIO. Expose these to userspace for usage as necessary.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Dual-role support was added in v4.12. We should be using
it for USB2 port on the am57xx-idk.
Cc: <stable@vger.kernel.org> [4.16+]
Reported-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The IO lines of MMC2 in am57xx-beagle-x15/am57xx-idk is connected to
3.3v. Use "ddr_3_3v" instead of "ddr_1_8v" to indicate DDR mode
works in 3.3v on these boards.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
pulldown
commit 18aa0f4bca701cb078a6 ("ARM: dts: am57xx-idk: Select pull down
for mmc1_clk line in default mode") modified mmc1_pins_default
pinctrl group in am57xx-idk-common.dtsi in order to change the CLK
line to PIN_INPUT_PULLDOWN. However instead of modifying the pinctrl
group, use the new pinctrl group "mmc1_pins_default_no_clk_pu" in
dra7-mmc-iodelay.dtsi added specifically to be used for CLK line without
external pull up.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
During a short period when the bus voltage is switched from 3.3v to 1.8v,
(to enumerate UHS mode), the mmc module is disabled and the mmc IO lines
are kept in a state according to the programmed pad mux pull type.
According to 4.2.4.2 Timing to Switch Signal Voltage in "SD Specifications
Part 1 Physical Layer Specification Version 5.00 February 22, 2016", the
host should hold CLK low for at least 5ms.
In order to keep the card line low during voltage switch, the pad mux of
mmc1_clk line should be configured to pull down.
This is specific to am57xx-idk (and not all dra72/dra74 based boards)
since mmc1_clk line in am57xx-idk is not connected to an external
pullup.
While at that change the order of header files in am571x-idk.dts and
am572x-idk.dts so that the modified pinctrl values in am57xx-idk-common
could take effect.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add vdd-supply as smps12_reg for cpu0.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Include dra72x-mmc-iodelay.dtsi which has pinmux and IODelay
configuration values for the various MMC modes for dra72 SoC
and use it in the pinctrl properties of MMC devicetree
nodes present in am571x-idk.dts.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
AM572x IDK and AM571x IDK boards have equivalent
design of how SD card and eMMC are connected.
The two EVMs mainly differ in IOdelay configuration
needed (because of difference in SoC used).
Move the common properties to am57xx-idk-common.dtsi
file which is common for both EVMs.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add pcie1 dt node in order for the controller to operate in
endpoint mode. However since none of the dra7 based boards have
slots configured to operate in endpoint mode, keep EP mode
disabled.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The GPIO polarity for MMC1 card detect is set to '0' which means
active-high. However the polarity should be active-low. Fix it
here.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Enable the System Mailboxes 5 and 6 and the corresponding
child sub-mailbox (IPC 3.x) nodes for the AM571x IDK board.
This is needed to enable communication with the respective
remote processors IPU1, IPU2, and DSP1 from the MPU.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
VBUS detection is available on the board via the palmas PMIC.
Use extcon-palmas driver instead of extcon-gpio-usb driver.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The AM571x-IDK board is a board based on TI's AM5718 SOC
which has a single core 1.5GHz A15 processor. This board is a
development platform for the Industrial market with:
- 1GB of DDR3L
- Dual 1Gbps Ethernet
- HDMI,
- PRU-ICSS
- uSD
- 16GB eMMC
- CAN
- RS-485
- PCIe
- USB3.0
- Video Input Port
- Industrial IO port and expansion connector
The link to the data sheet and TRM can be found here:
http://www.ti.com/product/AM5718
Initial support is only for basic peripherals.
Signed-off-by: Schuyler Patton <spatton@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
Kishon Vijay Abraham I
Tony Lindgren
Faiz Abbas
Thomas Gleixner
Roger Quadros
Keerthy
Andrew F. Davis
Dave Gerlach
Sekhar Nori
Suman Anna
Schuyler Patton