| Age | Commit message (Collapse) | Author |
|---|
|
|
|
commit d79e9d7c1e4ba5f95f2ff3541880c40ea9722212 upstream.
The correct setting for the RGMII ports on LS1046ARDB is to
enable delay on both Rx and Tx so the interface mode used must
be PHY_INTERFACE_MODE_RGMII_ID.
Since commit 1b3047b5208a80 ("net: phy: realtek: add support for
configuring the RX delay on RTL8211F") the Realtek 8211F PHY driver
has control over the RGMII RX delay and it is disabling it for
RGMII_TXID. The LS1046ARDB uses two such PHYs in RGMII_ID mode but
in the device tree the mode was described as "rgmii".
Changing the phy-connection-type to "rgmii-id" to address the issue.
Fixes: 3fa395d2c48a ("arm64: dts: add LS1046A DPAA FMan nodes")
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4022d808c45277693ea86478fab1f081ebf997e8 upstream.
The correct setting for the RGMII ports on LS1043ARDB is to
enable delay on both Rx and Tx so the interface mode used must
be PHY_INTERFACE_MODE_RGMII_ID.
Since commit 1b3047b5208a80 ("net: phy: realtek: add support for
configuring the RX delay on RTL8211F") the Realtek 8211F PHY driver
has control over the RGMII RX delay and it is disabling it for
RGMII_TXID. The LS1043ARDB uses two such PHYs in RGMII_ID mode but
in the device tree the mode was described as "rgmii_txid".
This issue was not apparent at the time as the PHY driver took the
same action for RGMII_TXID and RGMII_ID back then but it became
visible (RX no longer working) after the above patch.
Changing the phy-connection-type to "rgmii-id" to address the issue.
Fixes: bf02f2ffe59c ("arm64: dts: add LS1043A DPAA FMan support")
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit fe3a04824f75786e39ed74e82fb6cb2534c95fe4 upstream.
When the AHCI device node was added, it was added in the wrong location
in the device tree file. The device nodes should be sorted by register
address.
Move the device node to before EHCI1, where it belongs.
Fixes: 41c64d3318aa ("ARM: dts: sun8i: r40: add sata node")
Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0c5220a3c1242c7a2451570ed5f5af69620aac75 upstream.
Commit a758f50f10cf ("mtd: onenand: omap2: Configure driver from DT")
started using DT specified timings for GPMC, and as a result the
OneNAND stopped working on N900 as we had wrong values in the DT.
Fix by updating the values to bootloader timings that have been tested
to be working on Nokia N900 with OneNAND manufacturers: Samsung,
Numonyx.
Fixes: a758f50f10cf ("mtd: onenand: omap2: Configure driver from DT")
Signed-off-by: Arthur Demchenkov <spinal.by@gmail.com>
Tested-by: Merlijn Wajer <merlijn@wizzup.org>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 636b45b8efa91db05553840b6c0120d6fa6b94fa upstream.
The current set minimum voltage of 730000µV seems to be wrong. I don't
know the document which specifies that but the imx6qdl datasheets says
that the minimum voltage should be 0.925V for VDD_ARM (LDO bypassed,
lowest opp) and 1.15V for VDD_SOC (LDO bypassed, lowest opp).
Fixes: ddec5d1c0047 ("ARM: dts: imx6: Add initial support for phyCORE-i.MX 6 SOM")
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6687c201fdc3139315c2ea7ef96c157672805cdc upstream.
Define the sdhci pinctrl state as "default" so it gets applied
correctly and to match all other RPis.
Fixes: 2c7c040c73e9 ("ARM: dts: bcm2835: Add Raspberry Pi Zero W")
Signed-off-by: Nick Hudson <skrll@netbsd.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit deeabb4c1341a12bf8b599e6a2f4cfa4fd74738c upstream.
Disable all rps-irq interrupts during driver initialization to prevent
an accidental interrupt on GIC.
Fixes: 84316f4ef141 ("ARM: boot: dts: Add Oxford Semiconductor OX810SE dtsi")
Fixes: 38d4a53733f5 ("ARM: dts: Add support for OX820 and Pogoplug V3")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit db2c549407d4a76563c579e4768f7d6d32afefba upstream.
This patch fixes an off-by-one error in strncpy size argument in
tools/perf/util/map.c. The issue is that in:
strncmp(filename, "/system/lib/", 11)
the passed string literal: "/system/lib/" has 12 bytes (without the NULL
byte) and the passed size argument is 11. As a result, the logic won't
match the ending "/" byte and will pass filepaths that are stored in
other directories e.g. "/system/libmalicious/bin" or just
"/system/libmalicious".
This functionality seems to be present only on Android. I assume the
/system/ directory is only writable by the root user, so I don't think
this bug has much (or any) security impact.
Fixes: eca818369996 ("perf tools: Add automatic remapping of Android libraries")
Signed-off-by: disconnect3d <dominik.b.czarnota@gmail.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Changbin Du <changbin.du@intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: John Keeping <john@metanate.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Michael Lentine <mlentine@google.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Song Liu <songliubraving@fb.com>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lore.kernel.org/lkml/20200309104855.3775-1-dominik.b.czarnota@gmail.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6f5459da2b8736720afdbd67c4bd2d1edba7d0e3 upstream.
Building an arm64 defconfig with clang's integrated assembler, this error
occurs:
<instantiation>:2:2: error: unrecognized instruction mnemonic
_ASM_EXTABLE 9999b, 9f
^
arch/arm64/mm/cache.S:50:1: note: while in macro instantiation
user_alt 9f, "dc cvau, x4", "dc civac, x4", 0
^
While GNU as seems fine with case-sensitive macro instantiations, clang
doesn't, so use the actual macro name (_asm_extable) as in the rest of
the file.
Also checked that the generated assembly matches the GCC output.
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Tested-by: Nick Desaulniers <ndesaulniers@google.com>
Fixes: 290622efc76e ("arm64: fix "dc cvau" cache operation on errata-affected core")
Link: https://github.com/ClangBuiltLinux/linux/issues/924
Signed-off-by: Ilie Halip <ilie.halip@gmail.com>
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e886274031200bb60965c1b9c49b7acda56a93bd upstream.
Make it so that CEPH_MSG_DATA_PAGES data item can own pages,
fixing a bunch of memory leaks for a page vector allocated in
alloc_msg_with_page_vector(). Currently, only watch-notify
messages trigger this allocation, and normally the page vector
is freed either in handle_watch_notify() or by the caller of
ceph_osdc_notify(). But if the message is freed before that
(e.g. if the session faults while reading in the message or
if the notify is stale), we leak the page vector.
This was supposed to be fixed by switching to a message-owned
pagelist, but that never happened.
Fixes: 1907920324f1 ("libceph: support for sending notifies")
Reported-by: Roman Penyaev <rpenyaev@suse.de>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Roman Penyaev <rpenyaev@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5f3d9b07b9bb4679922f0b2e2baa770e74a6bbd3 upstream.
Currently enabling clkctrl clock on am4 can fail for RTC as the clock
parent is wrong for RTC.
Fixes: 76a1049b84dd ("clk: ti: am43xx: add new clkctrl data for am43xx")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lkml.kernel.org/r/20200221171030.39326-1-tony@atomide.com
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8400ab8896324641243b57fc49b448023c07409a upstream.
The imx SC api strongly assumes that messages are composed out of
4-bytes words but some of our message structs have odd sizeofs.
This produces many oopses with CONFIG_KASAN=y.
Fix by marking with __aligned(4).
Fixes: 666aed2d13ee ("clk: imx: scu: add set parent support")
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Link: https://lkml.kernel.org/r/aad021e432b3062c142973d09b766656eec18fde.1582216144.git.leonard.crestez@nxp.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a0ae04a25650fd51b7106e742d27333e502173c6 upstream.
The imx SC api strongly assumes that messages are composed out of
4-bytes words but some of our message structs have odd sizeofs.
This produces many oopses with CONFIG_KASAN=y.
Fix by marking with __aligned(4).
Fixes: fe37b4820417 ("clk: imx: add scu clock common part")
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Link: https://lkml.kernel.org/r/10e97a04980d933b2cfecb6b124bf9046b6e4f16.1582216144.git.leonard.crestez@nxp.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8262e6f9b1034ede34548a04dec4c302d92c9497 upstream.
This patch reverts 58292104832f ("net: ks8851-ml: Fix 16-bit IO operation")
and edacb098ea9c ("net: ks8851-ml: Fix 16-bit data access"), because it
turns out these were only necessary due to buggy hardware. This patch adds
a check for such a buggy hardware to prevent any such mistakes again.
While working further on the KS8851 driver, it came to light that the
KS8851-16MLL is capable of switching bus endianness by a hardware strap,
EESK pin. If this strap is incorrect, the IO accesses require such endian
swapping as is being reverted by this patch. Such swapping also impacts
the performance significantly.
Hence, in addition to removing it, detect that the hardware is broken,
report to user, and fail to bind with such hardware.
Fixes: 58292104832f ("net: ks8851-ml: Fix 16-bit IO operation")
Fixes: edacb098ea9c ("net: ks8851-ml: Fix 16-bit data access")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Petr Stetiar <ynezz@true.cz>
Cc: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0c625ccfe6f754d0896b8881f5c85bcb81699f1f upstream.
There are at least 3 models of the HP x2 10 models:
Bay Trail SoC + AXP288 PMIC
Cherry Trail SoC + AXP288 PMIC
Cherry Trail SoC + TI PMIC
Like on the other HP x2 10 models we need to ignore wakeup for ACPI GPIO
events on the external embedded-controller pin to avoid spurious wakeups
on the HP x2 10 CHT + AXP288 model too.
This commit adds an extra DMI based quirk for the HP x2 10 CHT + AXP288
model, ignoring wakeups for ACPI GPIO events on the EC interrupt pin
on this model. This fixes spurious wakeups from suspend on this model.
Fixes: aa23ca3d98f7 ("gpiolib: acpi: Add honor_wakeup module-option + quirk mechanism")
Reported-and-tested-by: Marc Lehmann <schmorp@schmorp.de>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20200302111225.6641-4-hdegoede@redhat.com
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5c6f25887963f15492b604dd25cb149c501bbabf upstream.
Trying to initialize a structure with "= {};" will not always clean out
all padding locations in a structure. So be explicit and call memset to
initialize everything for a number of bpf information structures that
are then copied from userspace, sometimes from smaller memory locations
than the size of the structure.
Reported-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/20200320162258.GA794295@kroah.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8096f229421f7b22433775e928d506f0342e5907 upstream.
For the bpf syscall, we are relying on the compiler to properly zero out
the bpf_attr union that we copy userspace data into. Unfortunately that
doesn't always work properly, padding and other oddities might not be
correctly zeroed, and in some tests odd things have been found when the
stack is pre-initialized to other values.
Fix this by explicitly memsetting the structure to 0 before using it.
Reported-by: Maciej Żenczykowski <maze@google.com>
Reported-by: John Stultz <john.stultz@linaro.org>
Reported-by: Alexander Potapenko <glider@google.com>
Reported-by: Alistair Delva <adelva@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://android-review.googlesource.com/c/kernel/common/+/1235490
Link: https://lore.kernel.org/bpf/20200320094813.GA421650@kroah.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 95b31e35239e5e1689e3d965d692a313c71bd8ab upstream.
The Lex 2I385SW board has two Intel I211 ethernet controllers. Without
this patch, only the first port is usable. The second port fails to
start with the following message:
igb: probe of 0000:02:00.0 failed with error -2
Fixes: 648e921888ad ("clk: x86: Stop marking clocks as CLK_IS_CRITICAL")
Tested-by: Georg Müller <georgmueller@gmx.net>
Signed-off-by: Georg Müller <georgmueller@gmx.net>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7cf64b18b0b96e751178b8d0505d8466ff5a448f upstream.
vt_in_use() dereferences console_driver->ttys[i] without proper locking.
This is broken because the tty can be closed and freed concurrently.
We could fix this by using 'READ_ONCE(console_driver->ttys[i]) != NULL'
and skipping the check of tty_struct::count. But, looking at
console_driver->ttys[i] isn't really appropriate anyway because even if
it is NULL the tty can still be in the process of being closed.
Instead, fix it by making vt_in_use() require console_lock() and check
whether the vt is allocated and has port refcount > 1. This works since
following the patch "vt: vt_ioctl: fix VT_DISALLOCATE freeing in-use
virtual console" the port refcount is incremented while the vt is open.
Reproducer (very unreliable, but it worked for me after a few minutes):
#include <fcntl.h>
#include <linux/vt.h>
int main()
{
int fd, nproc;
struct vt_stat state;
char ttyname[16];
fd = open("/dev/tty10", O_RDONLY);
for (nproc = 1; nproc < 8; nproc *= 2)
fork();
for (;;) {
sprintf(ttyname, "/dev/tty%d", rand() % 8);
close(open(ttyname, O_RDONLY));
ioctl(fd, VT_GETSTATE, &state);
}
}
KASAN report:
BUG: KASAN: use-after-free in vt_in_use drivers/tty/vt/vt_ioctl.c:48 [inline]
BUG: KASAN: use-after-free in vt_ioctl+0x1ad3/0x1d70 drivers/tty/vt/vt_ioctl.c:657
Read of size 4 at addr ffff888065722468 by task syz-vt2/132
CPU: 0 PID: 132 Comm: syz-vt2 Not tainted 5.6.0-rc5-00130-g089b6d3654916 #13
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS ?-20191223_100556-anatol 04/01/2014
Call Trace:
[...]
vt_in_use drivers/tty/vt/vt_ioctl.c:48 [inline]
vt_ioctl+0x1ad3/0x1d70 drivers/tty/vt/vt_ioctl.c:657
tty_ioctl+0x9db/0x11b0 drivers/tty/tty_io.c:2660
[...]
Allocated by task 136:
[...]
kzalloc include/linux/slab.h:669 [inline]
alloc_tty_struct+0x96/0x8a0 drivers/tty/tty_io.c:2982
tty_init_dev+0x23/0x350 drivers/tty/tty_io.c:1334
tty_open_by_driver drivers/tty/tty_io.c:1987 [inline]
tty_open+0x3ca/0xb30 drivers/tty/tty_io.c:2035
[...]
Freed by task 41:
[...]
kfree+0xbf/0x200 mm/slab.c:3757
free_tty_struct+0x8d/0xb0 drivers/tty/tty_io.c:177
release_one_tty+0x22d/0x2f0 drivers/tty/tty_io.c:1468
process_one_work+0x7f1/0x14b0 kernel/workqueue.c:2264
worker_thread+0x8b/0xc80 kernel/workqueue.c:2410
[...]
Fixes: 4001d7b7fc27 ("vt: push down the tty lock so we can see what is left to tackle")
Cc: <stable@vger.kernel.org> # v3.4+
Acked-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Link: https://lore.kernel.org/r/20200322034305.210082-3-ebiggers@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ca4463bf8438b403596edd0ec961ca0d4fbe0220 upstream.
The VT_DISALLOCATE ioctl can free a virtual console while tty_release()
is still running, causing a use-after-free in con_shutdown(). This
occurs because VT_DISALLOCATE considers a virtual console's
'struct vc_data' to be unused as soon as the corresponding tty's
refcount hits 0. But actually it may be still being closed.
Fix this by making vc_data be reference-counted via the embedded
'struct tty_port'. A newly allocated virtual console has refcount 1.
Opening it for the first time increments the refcount to 2. Closing it
for the last time decrements the refcount (in tty_operations::cleanup()
so that it happens late enough), as does VT_DISALLOCATE.
Reproducer:
#include <fcntl.h>
#include <linux/vt.h>
#include <sys/ioctl.h>
#include <unistd.h>
int main()
{
if (fork()) {
for (;;)
close(open("/dev/tty5", O_RDWR));
} else {
int fd = open("/dev/tty10", O_RDWR);
for (;;)
ioctl(fd, VT_DISALLOCATE, 5);
}
}
KASAN report:
BUG: KASAN: use-after-free in con_shutdown+0x76/0x80 drivers/tty/vt/vt.c:3278
Write of size 8 at addr ffff88806a4ec108 by task syz_vt/129
CPU: 0 PID: 129 Comm: syz_vt Not tainted 5.6.0-rc2 #11
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS ?-20191223_100556-anatol 04/01/2014
Call Trace:
[...]
con_shutdown+0x76/0x80 drivers/tty/vt/vt.c:3278
release_tty+0xa8/0x410 drivers/tty/tty_io.c:1514
tty_release_struct+0x34/0x50 drivers/tty/tty_io.c:1629
tty_release+0x984/0xed0 drivers/tty/tty_io.c:1789
[...]
Allocated by task 129:
[...]
kzalloc include/linux/slab.h:669 [inline]
vc_allocate drivers/tty/vt/vt.c:1085 [inline]
vc_allocate+0x1ac/0x680 drivers/tty/vt/vt.c:1066
con_install+0x4d/0x3f0 drivers/tty/vt/vt.c:3229
tty_driver_install_tty drivers/tty/tty_io.c:1228 [inline]
tty_init_dev+0x94/0x350 drivers/tty/tty_io.c:1341
tty_open_by_driver drivers/tty/tty_io.c:1987 [inline]
tty_open+0x3ca/0xb30 drivers/tty/tty_io.c:2035
[...]
Freed by task 130:
[...]
kfree+0xbf/0x1e0 mm/slab.c:3757
vt_disallocate drivers/tty/vt/vt_ioctl.c:300 [inline]
vt_ioctl+0x16dc/0x1e30 drivers/tty/vt/vt_ioctl.c:818
tty_ioctl+0x9db/0x11b0 drivers/tty/tty_io.c:2660
[...]
Fixes: 4001d7b7fc27 ("vt: push down the tty lock so we can see what is left to tackle")
Cc: <stable@vger.kernel.org> # v3.4+
Reported-by: syzbot+522643ab5729b0421998@syzkaller.appspotmail.com
Acked-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Link: https://lore.kernel.org/r/20200322034305.210082-2-ebiggers@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1aa6e058dd6cd04471b1f21298270014daf48ac9 upstream.
The vc_cons_allocated() checks in vt_ioctl() and vt_compat_ioctl() are
unnecessary because they can only be reached by calling ioctl() on an
open tty, which implies the corresponding virtual console is allocated.
And even if the virtual console *could* be freed concurrently, then
these checks would be broken since they aren't done under console_lock,
and the vc_data is dereferenced before them anyway.
So, remove these unneeded checks to avoid confusion.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Link: https://lore.kernel.org/r/20200224080326.295046-1-ebiggers@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f400991bf872debffb01c46da882dc97d7e3248e upstream.
vt_dont_switch is pure boolean, no need for whole char.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20200219073951.16151-6-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e587e8f17433ddb26954f0edf5b2f95c42155ae9 upstream.
These two were macros. Switch them to static inlines, so that it's more
understandable what they are doing.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20200219073951.16151-2-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit dce05aa6eec977f1472abed95ccd71276b9a3864 upstream.
Avoid global variables (namely sel_cons) by introducing vc_is_sel. It
checks whether the parameter is the current selection console. This will
help putting sel_cons to a struct later.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20200219073951.16151-1-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit efc176929a3505a30c3993ddd393b40893649bd2 upstream.
We should validate if the 'sup' is NULL or not before freeing DMA
memory, to fix below warning.
"drivers/tty/serial/sprd_serial.c:1141 sprd_remove()
error: we previously assumed 'sup' could be null (see line 1132)"
Fixes: f4487db58eb7 ("serial: sprd: Add DMA mode support")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Lanqing Liu <liuhhome@gmail.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/e2bd92691538e95b04a2c2a728f3292e1617018f.1584325957.git.liuhhome@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit be8c827f50a0bcd56361b31ada11dc0a3c2fd240 upstream.
The original patch didn't copy the ieee80211_is_data() condition
because on most drivers the management frames don't go through
this path. However, they do on iwlwifi/mvm, so we do need to keep
the condition here.
Cc: stable@vger.kernel.org
Fixes: ce2e1ca70307 ("mac80211: Check port authorization in the ieee80211_tx_dequeue() case")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Woody Suwalski <terraluna977@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ce2e1ca703071723ca2dd94d492a5ab6d15050da upstream.
mac80211 used to check port authorization in the Data frame enqueue case
when going through start_xmit(). However, that authorization status may
change while the frame is waiting in a queue. Add a similar check in the
dequeue case to avoid sending previously accepted frames after
authorization change. This provides additional protection against
potential leaking of frames after a station has been disconnected and
the keys for it are being removed.
Cc: stable@vger.kernel.org
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Link: https://lore.kernel.org/r/20200326155133.ced84317ea29.I34d4c47cd8cc8a4042b38a76f16a601fbcbfd9b3@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
|
|
commit 2c64605b590edadb3fb46d1ec6badb49e940b479 upstream.
net/netfilter/nft_fwd_netdev.c: In function ‘nft_fwd_netdev_eval’:
net/netfilter/nft_fwd_netdev.c:32:10: error: ‘struct sk_buff’ has no member named ‘tc_redirected’
pkt->skb->tc_redirected = 1;
^~
net/netfilter/nft_fwd_netdev.c:33:10: error: ‘struct sk_buff’ has no member named ‘tc_from_ingress’
pkt->skb->tc_from_ingress = 1;
^~
To avoid a direct dependency with tc actions from netfilter, wrap the
redirect bits around CONFIG_NET_REDIRECT and move helpers to
include/linux/skbuff.h. Turn on this toggle from the ifb driver, the
only existing client of these bits in the tree.
This patch adds skb_set_redirected() that sets on the redirected bit
on the skbuff, it specifies if the packet was redirect from ingress
and resets the timestamp (timestamp reset was originally missing in the
netfilter bugfix).
Fixes: bcfabee1afd99484 ("netfilter: nft_fwd_netdev: allow to redirect to ifb via ingress")
Reported-by: noreply@ellerman.id.au
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6990570f7e0a6078e11b9c5dc13f4b6e3f49a398 upstream.
sd->devnode is released after calling
v4l2_subdev_release. Therefore it should be set
to NULL so that the subdev won't hold a pointer
to a released object. This fixes a reference
after free bug in function
v4l2_device_unregister_subdev
Fixes: 0e43734d4c46e ("media: v4l2-subdev: add release() internal op")
Cc: stable@vger.kernel.org
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Reviewed-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a246b4d547708f33ff4d4b9a7a5dbac741dc89d8 upstream.
Make sure to check that we have two alternate settings and at least one
endpoint before accessing the second altsetting structure and
dereferencing the endpoint arrays.
This specifically avoids dereferencing NULL-pointers or corrupting
memory when a device does not have the expected descriptors.
Note that the sanity check in cit_get_packet_size() is not redundant as
the driver is mixing looking up altsettings by index and by number,
which may not coincide.
Fixes: 659fefa0eb17 ("V4L/DVB: gspca_xirlink_cit: Add support for camera with a bcd version of 0.01")
Fixes: 59f8b0bf3c12 ("V4L/DVB: gspca_xirlink_cit: support bandwidth changing for devices with 1 alt setting")
Cc: stable <stable@vger.kernel.org> # 2.6.37
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 485b06aadb933190f4bc44e006076bc27a23f205 upstream.
Make sure to check that we have two alternate settings and at least one
endpoint before accessing the second altsetting structure and
dereferencing the endpoint arrays.
This specifically avoids dereferencing NULL-pointers or corrupting
memory when a device does not have the expected descriptors.
Note that the sanity checks in stv06xx_start() and pb0100_start() are
not redundant as the driver is mixing looking up altsettings by index
and by number, which may not coincide.
Fixes: 8668d504d72c ("V4L/DVB (12082): gspca_stv06xx: Add support for st6422 bridge and sensor")
Fixes: c0b33bdc5b8d ("[media] gspca-stv06xx: support bandwidth changing")
Cc: stable <stable@vger.kernel.org> # 2.6.31
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f52981019ad8d6718de79b425a574c6bddf81f7c upstream.
Make sure to use the current alternate setting when verifying the
interface descriptors to avoid submitting an URB to an invalid endpoint.
Failing to do so could cause the driver to misbehave or trigger a WARN()
in usb_submit_urb() that kernels with panic_on_warn set would choke on.
Fixes: c4018fa2e4c0 ("[media] dib0700: fix RC support on Hauppauge Nova-TD")
Cc: stable <stable@vger.kernel.org> # 3.16
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 998912346c0da53a6dbb71fab3a138586b596b30 upstream.
Make sure to check that we have at least one endpoint before accessing
the endpoint array to avoid dereferencing a NULL-pointer on stream
start.
Note that these sanity checks are not redundant as the driver is mixing
looking up altsettings by index and by number, which need not coincide.
Fixes: 1876bb923c98 ("V4L/DVB (12079): gspca_ov519: add support for the ov511 bridge")
Fixes: b282d87332f5 ("V4L/DVB (12080): gspca_ov519: Fix ov518+ with OV7620AE (Trust spacecam 320)")
Cc: stable <stable@vger.kernel.org> # 2.6.31
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a65cab7d7f05c2061a3e2490257d3086ff3202c6 upstream.
Reading from a debugfs file at a nonzero position, without first reading
at position 0, leaks uninitialized memory to userspace.
It's a bit tricky to do this, since lseek() and pread() aren't allowed
on these files, and write() doesn't update the position on them. But
writing to them with splice() *does* update the position:
#define _GNU_SOURCE 1
#include <fcntl.h>
#include <stdio.h>
#include <unistd.h>
int main()
{
int pipes[2], fd, n, i;
char buf[32];
pipe(pipes);
write(pipes[1], "0", 1);
fd = open("/sys/kernel/debug/fault_around_bytes", O_RDWR);
splice(pipes[0], NULL, fd, NULL, 1, 0);
n = read(fd, buf, sizeof(buf));
for (i = 0; i < n; i++)
printf("%02x", buf[i]);
printf("\n");
}
Output:
5a5a5a5a5a5a5a5a5a5a5a5a5a5a5a5a5a5a5a5a5a5a5a30
Fix the infoleak by making simple_attr_read() always fill
simple_attr::get_buf if it hasn't been filled yet.
Reported-by: syzbot+fcab69d1ada3e8d6f06b@syzkaller.appspotmail.com
Reported-by: Alexander Potapenko <glider@google.com>
Fixes: acaefc25d21f ("[PATCH] libfs: add simple attribute files")
Cc: stable@vger.kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
Acked-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20200308023849.988264-1-ebiggers@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 32d2545462c6cede998267b86e57cda5d1dc2225 upstream.
Add the PCI ID to the driver list to support this new device.
Cc: stable@vger.kernel.org
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1165dd73e811a07d947aee218510571f516081f6 upstream.
We can't handle the case length > WLAN_DATA_MAXLEN.
Because the size of rxfrm->data is WLAN_DATA_MAXLEN(2312), and we can't
read more than that.
Thanks-to: Hillf Danton <hdanton@sina.com>
Reported-and-tested-by: syzbot+7d42d68643a35f71ac8a@syzkaller.appspotmail.com
Signed-off-by: Qiujun Huang <hqjagain@gmail.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200326131850.17711-1-hqjagain@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a1f165a6b738f0c9d744bad4af7a53909278f5fc upstream.
We should cancel hw->usb_work before kfree(hw).
Reported-by: syzbot+6d2e7f6fa90e27be9d62@syzkaller.appspotmail.com
Signed-off-by: Qiujun Huang <hqjagain@gmail.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/1585120006-30042-1-git-send-email-hqjagain@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 38ef48f7d4b7342f145a1b4f96023bde99aeb245 upstream.
The ASUS USB-N10 Nano B1 has been reported as a new RTL8188EU device.
Add it to the device tables.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Reported-by: kovi <zraetn@gmail.com>
Cc: Stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200321180011.26153-1-Larry.Finger@lwfinger.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 72db61d7d17a475d3cc9de1a7c871d518fcd82f0 upstream.
This function should not allow negative values of "wr_val". If
negatives are allowed then capping the upper bound at 7 is
meaningless. Let's make it unsigned.
Fixes: 7dc7967fc39a ("staging: kpc2000: add initial set of Daktronics drivers")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200224103325.hrxdnaeqsthplu42@kili.mountain
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 536f561d871c5781bc33d26d415685211b94032e upstream.
The driver was issuing synchronous uninterruptible control requests
without using a timeout. This could lead to the driver hanging on
various user requests due to a malfunctioning (or malicious) device
until the device is physically disconnected.
The USB upper limit of five seconds per request should be more than
enough.
Fixes: f3d27f34fdd7 ("[media] usbtv: Add driver for Fushicai USBTV007 video frame grabber")
Fixes: c53a846c48f2 ("[media] usbtv: add video controls")
Cc: stable <stable@vger.kernel.org> # 3.11
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Lubomir Rintel <lkundrak@v3.sk>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit bca243b1ce0e46be26f7c63b5591dfbb41f558e5 upstream.
commit 1b976fc6d684 ("media: b2c2-flexcop-usb: add sanity checking") added
an endpoint sanity check to address a NULL-pointer dereference on probe.
Unfortunately the check was done on the current altsetting which was later
changed.
Fix this by moving the sanity check to after the altsetting is changed.
Fixes: 1b976fc6d684 ("media: b2c2-flexcop-usb: add sanity checking")
Cc: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 52974d94a206ce428d9d9b6eaa208238024be82a upstream.
When handling a PIO bulk transfer with highmem buffer, a temporary
mapping is assigned to urb->transfer_buffer. After the transfer is
complete, an invalid address is left behind in this pointer. This is
not ordinarily a problem since nothing touches that buffer before the
urb is released. However, when usbmon is active, usbmon_urb_complete()
calls (indirectly) mon_bin_get_data() which does access the transfer
buffer if it is set. To prevent an invalid memory access here, reset
urb->transfer_buffer to NULL when finished (musb_host_rx()), or do not
set it at all (musb_host_tx()).
Fixes: 8e8a55165469 ("usb: musb: host: Handle highmem in PIO mode")
Signed-off-by: Mans Rullgard <mans@mansr.com>
Cc: stable@vger.kernel.org
Signed-off-by: Bin Liu <b-liu@ti.com>
Link: https://lore.kernel.org/r/20200316211136.2274-8-b-liu@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 57aa9f294b09463492f604feaa5cc719beaace32 upstream.
Fix slab-out-of-bounds read in the interrupt-URB completion handler.
The boundary condition should be (length - 1) as we access
data[position + 1].
Reported-and-tested-by: syzbot+37ba33391ad5f3935bbd@syzkaller.appspotmail.com
Signed-off-by: Qiujun Huang <hqjagain@gmail.com>
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 62d65bdd9d05158aa2547f8ef72375535f3bc6e3 upstream.
commit b401f8c4f492c ("USB: cdc-acm: fix rounding error in TIOCSSERIAL")
introduced a regression by changing the order of capability and close
settings change checks. When running with CAP_SYS_ADMIN setting the
close settings to the values already set resulted in -EOPNOTSUPP.
Fix this by changing the check order back to how it was before.
Fixes: b401f8c4f492c ("USB: cdc-acm: fix rounding error in TIOCSSERIAL")
Cc: Anthony Mallet <anthony.mallet@laas.fr>
Cc: stable <stable@vger.kernel.org>
Cc: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Matthias Reichl <hias@horus.com>
Link: https://lore.kernel.org/r/20200327150350.3657-1-hias@horus.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit dfee7e2f478346b12ea651d5c28b069f6a4af563 upstream.
This modem is embedded on dlink dwr-960 router.
The oem configuration states:
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1435 ProdID=d191 Rev=ff.ff
S: Manufacturer=Android
S: Product=Android
S: SerialNumber=0123456789ABCDEF
C:* #Ifs= 6 Cfg#= 1 Atr=80 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none)
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)
E: Ad=84(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)
E: Ad=86(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
E: Ad=88(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=(none)
E: Ad=89(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=125us
Tested on openwrt distribution
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6cb2669cb97fc4fdf526127159ac59caae052247 upstream.
BroadMobi BM806U is an Qualcomm MDM9225 based 3G/4G modem.
Tested hardware BM806U is mounted on D-Link DWR-921-C3 router.
T: Bus=01 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 2 Spd=480 MxCh= 0
D: Ver= 2.01 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=2020 ProdID=2033 Rev= 2.28
S: Manufacturer=Mobile Connect
S: Product=Mobile Connect
S: SerialNumber=f842866cfd5a
C:* #Ifs= 5 Cfg#= 1 Atr=80 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=87(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
E: Ad=89(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Co-developed-by: Cezary Jackiewicz <cezary@eko.one.pl>
Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 007d20dca2376a751b1dad03442f118438b7e65e upstream.
ASKEY WWHC050 is a mcie LTE modem.
The oem configuration states:
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1690 ProdID=7588 Rev=ff.ff
S: Manufacturer=Android
S: Product=Android
S: SerialNumber=813f0eef6e6e
C:* #Ifs= 6 Cfg#= 1 Atr=80 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none)
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=84(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=86(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
E: Ad=88(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=(none)
E: Ad=89(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=125us
Tested on openwrt distribution.
Co-developed-by: Cezary Jackiewicz <cezary@eko.one.pl>
Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f2d67fec0b43edce8c416101cdc52e71145b5fef upstream.
Anatoly has been fuzzing with kBdysch harness and reported a hang in
one of the outcomes:
0: (b7) r0 = 808464432
1: (7f) r0 >>= r0
2: (14) w0 -= 808464432
3: (07) r0 += 808464432
4: (b7) r1 = 808464432
5: (de) if w1 s<= w0 goto pc+0
R0_w=invP(id=0,umin_value=808464432,umax_value=5103431727,var_off=(0x30303020;0x10000001f)) R1_w=invP808464432 R10=fp0
6: (07) r0 += -2144337872
7: (14) w0 -= -1607454672
8: (25) if r0 > 0x30303030 goto pc+0
R0_w=invP(id=0,umin_value=271581184,umax_value=271581311,var_off=(0x10300000;0x7f)) R1_w=invP808464432 R10=fp0
9: (76) if w0 s>= 0x303030 goto pc+2
12: (95) exit
from 8 to 9: safe
from 5 to 6: R0_w=invP(id=0,umin_value=808464432,umax_value=5103431727,var_off=(0x30303020;0x10000001f)) R1_w=invP808464432 R10=fp0
6: (07) r0 += -2144337872
7: (14) w0 -= -1607454672
8: (25) if r0 > 0x30303030 goto pc+0
R0_w=invP(id=0,umin_value=271581184,umax_value=271581311,var_off=(0x10300000;0x7f)) R1_w=invP808464432 R10=fp0
9: safe
from 8 to 9: safe
verification time 589 usec
stack depth 0
processed 17 insns (limit 1000000) [...]
The underlying program was xlated as follows:
# bpftool p d x i 9
0: (b7) r0 = 808464432
1: (7f) r0 >>= r0
2: (14) w0 -= 808464432
3: (07) r0 += 808464432
4: (b7) r1 = 808464432
5: (de) if w1 s<= w0 goto pc+0
6: (07) r0 += -2144337872
7: (14) w0 -= -1607454672
8: (25) if r0 > 0x30303030 goto pc+0
9: (76) if w0 s>= 0x303030 goto pc+2
10: (05) goto pc-1
11: (05) goto pc-1
12: (95) exit
The verifier rewrote original instructions it recognized as dead code with
'goto pc-1', but reality differs from verifier simulation in that we're
actually able to trigger a hang due to hitting the 'goto pc-1' instructions.
Taking different examples to make the issue more obvious: in this example
we're probing bounds on a completely unknown scalar variable in r1:
[...]
5: R0_w=inv1 R1_w=inv(id=0) R10=fp0
5: (18) r2 = 0x4000000000
7: R0_w=inv1 R1_w=inv(id=0) R2_w=inv274877906944 R10=fp0
7: (18) r3 = 0x2000000000
9: R0_w=inv1 R1_w=inv(id=0) R2_w=inv274877906944 R3_w=inv137438953472 R10=fp0
9: (18) r4 = 0x400
11: R0_w=inv1 R1_w=inv(id=0) R2_w=inv274877906944 R3_w=inv137438953472 R4_w=inv1024 R10=fp0
11: (18) r5 = 0x200
13: R0_w=inv1 R1_w=inv(id=0) R2_w=inv274877906944 R3_w=inv137438953472 R4_w=inv1024 R5_w=inv512 R10=fp0
13: (2d) if r1 > r2 goto pc+4
R0_w=inv1 R1_w=inv(id=0,umax_value=274877906944,var_off=(0x0; 0x7fffffffff)) R2_w=inv274877906944 R3_w=inv137438953472 R4_w=inv1024 R5_w=inv512 R10=fp0
14: R0_w=inv1 R1_w=inv(id=0,umax_value=274877906944,var_off=(0x0; 0x7fffffffff)) R2_w=inv274877906944 R3_w=inv137438953472 R4_w=inv1024 R5_w=inv512 R10=fp0
14: (ad) if r1 < r3 goto pc+3
R0_w=inv1 R1_w=inv(id=0,umin_value=137438953472,umax_value=274877906944,var_off=(0x0; 0x7fffffffff)) R2_w=inv274877906944 R3_w=inv137438953472 R4_w=inv1024 R5_w=inv512 R10=fp0
15: R0=inv1 R1=inv(id=0,umin_value=137438953472,umax_value=274877906944,var_off=(0x0; 0x7fffffffff)) R2=inv274877906944 R3=inv137438953472 R4=inv1024 R5=inv512 R10=fp0
15: (2e) if w1 > w4 goto pc+2
R0=inv1 R1=inv(id=0,umin_value=137438953472,umax_value=274877906944,var_off=(0x0; 0x7f00000000)) R2=inv274877906944 R3=inv137438953472 R4=inv1024 R5=inv512 R10=fp0
16: R0=inv1 R1=inv(id=0,umin_value=137438953472,umax_value=274877906944,var_off=(0x0; 0x7f00000000)) R2=inv274877906944 R3=inv137438953472 R4=inv1024 R5=inv512 R10=fp0
16: (ae) if w1 < w5 goto pc+1
R0=inv1 R1=inv(id=0,umin_value=137438953472,umax_value=274877906944,var_off=(0x0; 0x7f00000000)) R2=inv274877906944 R3=inv137438953472 R4=inv1024 R5=inv512 R10=fp0
[...]
We're first probing lower/upper bounds via jmp64, later we do a similar
check via jmp32 and examine the resulting var_off there. After fall-through
in insn 14, we get the following bounded r1 with 0x7fffffffff unknown marked
bits in the variable section.
Thus, after knowing r1 <= 0x4000000000 and r1 >= 0x2000000000:
max: 0b100000000000000000000000000000000000000 / 0x4000000000
var: 0b111111111111111111111111111111111111111 / 0x7fffffffff
min: 0b010000000000000000000000000000000000000 / 0x2000000000
Now, in insn 15 and 16, we perform a similar probe with lower/upper bounds
in jmp32.
Thus, after knowing r1 <= 0x4000000000 and r1 >= 0x2000000000 and
w1 <= 0x400 and w1 >= 0x200:
max: 0b100000000000000000000000000000000000000 / 0x4000000000
var: 0b111111100000000000000000000000000000000 / 0x7f00000000
min: 0b010000000000000000000000000000000000000 / 0x2000000000
The lower/upper bounds haven't changed since they have high bits set in
u64 space and the jmp32 tests can only refine bounds in the low bits.
However, for the var part the expectation would have been 0x7f000007ff
or something less precise up to 0x7fffffffff. A outcome of 0x7f00000000
is not correct since it would contradict the earlier probed bounds
where we know that the result should have been in [0x200,0x400] in u32
space. Therefore, tests with such info will lead to wrong verifier
assumptions later on like falsely predicting conditional jumps to be
always taken, etc.
The issue here is that __reg_bound_offset32()'s implementation from
commit 581738a681b6 ("bpf: Provide better register bounds after jmp32
instructions") makes an incorrect range assumption:
static void __reg_bound_offset32(struct bpf_reg_state *reg)
{
u64 mask = 0xffffFFFF;
struct tnum range = tnum_range(reg->umin_value & mask,
reg->umax_value & mask);
struct tnum lo32 = tnum_cast(reg->var_off, 4);
struct tnum hi32 = tnum_lshift(tnum_rshift(reg->var_off, 32), 32);
reg->var_off = tnum_or(hi32, tnum_intersect(lo32, range));
}
In the above walk-through example, __reg_bound_offset32() as-is chose
a range after masking with 0xffffffff of [0x0,0x0] since umin:0x2000000000
and umax:0x4000000000 and therefore the lo32 part was clamped to 0x0 as
well. However, in the umin:0x2000000000 and umax:0x4000000000 range above
we'd end up with an actual possible interval of [0x0,0xffffffff] for u32
space instead.
In case of the original reproducer, the situation looked as follows at
insn 5 for r0:
[...]
5: R0_w=invP(id=0,umin_value=808464432,umax_value=5103431727,var_off=(0x0; 0x1ffffffff)) R1_w=invP808464432 R10=fp0
0x30303030 0x13030302f
5: (de) if w1 s<= w0 goto pc+0
R0_w=invP(id=0,umin_value=808464432,umax_value=5103431727,var_off=(0x30303020; 0x10000001f)) R1_w=invP808464432 R10=fp0
0x30303030 0x13030302f
[...]
After the fall-through, we similarly forced the var_off result into
the wrong range [0x30303030,0x3030302f] suggesting later on that fixed
bits must only be of 0x30303020 with 0x10000001f unknowns whereas such
assumption can only be made when both bounds in hi32 range match.
Originally, I was thinking to fix this by moving reg into a temp reg and
use proper coerce_reg_to_size() helper on the temp reg where we can then
based on that define the range tnum for later intersection:
static void __reg_bound_offset32(struct bpf_reg_state *reg)
{
struct bpf_reg_state tmp = *reg;
struct tnum lo32, hi32, range;
coerce_reg_to_size(&tmp, 4);
range = tnum_range(tmp.umin_value, tmp.umax_value);
lo32 = tnum_cast(reg->var_off, 4);
hi32 = tnum_lshift(tnum_rshift(reg->var_off, 32), 32);
reg->var_off = tnum_or(hi32, tnum_intersect(lo32, range));
}
In the case of the concrete example, this gives us a more conservative unknown
section. Thus, after knowing r1 <= 0x4000000000 and r1 >= 0x2000000000 and
w1 <= 0x400 and w1 >= 0x200:
max: 0b100000000000000000000000000000000000000 / 0x4000000000
var: 0b111111111111111111111111111111111111111 / 0x7fffffffff
min: 0b010000000000000000000000000000000000000 / 0x2000000000
However, above new __reg_bound_offset32() has no effect on refining the
knowledge of the register contents. Meaning, if the bounds in hi32 range
mismatch we'll get the identity function given the range reg spans
[0x0,0xffffffff] and we cast var_off into lo32 only to later on binary
or it again with the hi32.
Likewise, if the bounds in hi32 range match, then we mask both bounds
with 0xffffffff, use the resulting umin/umax for the range to later
intersect the lo32 with it. However, _prior_ called __reg_bound_offset()
did already such intersection on the full reg and we therefore would only
repeat the same operation on the lo32 part twice.
Given this has no effect and the original commit had false assumptions,
this patch reverts the code entirely which is also more straight forward
for stable trees: apparently 581738a681b6 got auto-selected by Sasha's
ML system and misclassified as a fix, so it got sucked into v5.4 where
it should never have landed. A revert is low-risk also from a user PoV
since it requires a recent kernel and llc to opt-into -mcpu=v3 BPF CPU
to generate jmp32 instructions. A proper bounds refinement would need a
significantly more complex approach which is currently being worked, but
no stable material [0]. Hence revert is best option for stable. After the
revert, the original reported program gets rejected as follows:
1: (7f) r0 >>= r0
2: (14) w0 -= 808464432
3: (07) r0 += 808464432
4: (b7) r1 = 808464432
5: (de) if w1 s<= w0 goto pc+0
R0_w=invP(id=0,umin_value=808464432,umax_value=5103431727,var_off=(0x0; 0x1ffffffff)) R1_w=invP808464432 R10=fp0
6: (07) r0 += -2144337872
7: (14) w0 -= -1607454672
8: (25) if r0 > 0x30303030 goto pc+0
R0_w=invP(id=0,umax_value=808464432,var_off=(0x0; 0x3fffffff)) R1_w=invP808464432 R10=fp0
9: (76) if w0 s>= 0x303030 goto pc+2
R0=invP(id=0,umax_value=3158063,var_off=(0x0; 0x3fffff)) R1=invP808464432 R10=fp0
10: (30) r0 = *(u8 *)skb[808464432]
BPF_LD_[ABS|IND] uses reserved fields
processed 11 insns (limit 1000000) [...]
[0] https://lore.kernel.org/bpf/158507130343.15666.8018068546764556975.stgit@john-Precision-5820-Tower/T/
Fixes: 581738a681b6 ("bpf: Provide better register bounds after jmp32 instructions")
Reported-by: Anatoly Trosinenko <anatoly.trosinenko@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200330160324.15259-2-daniel@iogearbox.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
Greg Kroah-Hartman
Madalin Bucur
Chen-Yu Tsai
Arthur Demchenkov
Marco Felsch
Nick Hudson
Sungbo Eo
disconnect3d
Ilie Halip
Ilya Dryomov
Tony Lindgren
Leonard Crestez
Marek Vasut
Hans de Goede
Georg Müller
Eric Biggers
Jiri Slaby
Lanqing Liu
Johannes Berg
Jouni Malinen
Pablo Neira Ayuso
Dafna Hirschfeld
Johan Hovold
Kai-Heng Feng
Qiujun Huang
Larry Finger
Dan Carpenter
Mans Rullgard
Matthias Reichl
Pawel Dembicki
Daniel Borkmann