| Age | Commit message (Collapse) | Author |
|---|
|
|
|
This is the 5.2.30 stable release
# gpg: Signature made Sun 19 Jan 2020 03:13:54 PM EST
# gpg: using RSA key EBCE84042C07D1D6
# gpg: Can't check signature: No public key
|
|
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit ada9e3fcc175db4538f5b5e05abf5dedf626e550 upstream.
This patch reverts commit 6e0a32d6f376 ("spi: dw: Fix default polarity
of native chipselect").
The SPI framework always called the set_cs callback with the logic
level it desired on the chip select line, which is what the drivers
original handling supported. commit f3186dd87669 ("spi: Optionally
use GPIO descriptors for CS GPIOs") changed these symantics, but only
in the case of drivers that also support GPIO chip selects, to true
meaning apply slave select rather than logic high. This left things in
an odd state where a driver that only supports hardware chip selects,
the core would handle polarity but if the driver supported GPIOs as
well the driver should handle polarity. At this point the reverted
change was applied to change the logic in the driver to match new
system.
This was then broken by commit 3e5ec1db8bfe ("spi: Fix SPI_CS_HIGH
setting when using native and GPIO CS") which reverted the core back
to consistently calling set_cs with a logic level.
This fix reverts the driver code back to its original state to match
the current core code. This is probably a better fix as a) the set_cs
callback is always called with consistent symantics and b) the
inversion for SPI_CS_HIGH can be handled in the core and doesn't need
to be coded in each driver supporting it.
Fixes: 3e5ec1db8bfe ("spi: Fix SPI_CS_HIGH setting when using native and GPIO CS")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191127153936.29719-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 61acd19f9c56fa0809285346bd0bd4a926ab0da0 upstream.
To fix a regression on the Cadence SPI driver, this patch reverts
commit 6046f5407ff0 ("spi: cadence: Fix default polarity of native
chipselect").
This patch was not the correct fix for the issue. The SPI framework
calls the set_cs line with the logic level it desires on the chip select
line, as such the old is_high handling was correct. However, this was
broken by the fact that before commit 3e5ec1db8bfe ("spi: Fix SPI_CS_HIGH
setting when using native and GPIO CS") all controllers that offered
the use of a GPIO chip select had SPI_CS_HIGH applied, even for hardware
chip selects. This caused the value passed into the driver to be inverted.
Which unfortunately makes it look like a logical enable the chip select
value.
Since the core was corrected to not unconditionally apply SPI_CS_HIGH,
the Cadence driver, whilst using the hardware chip select, will deselect
the chip select every time we attempt to communicate with the device,
which results in failed communications.
Fixes: 3e5ec1db8bfe ("spi: Fix SPI_CS_HIGH setting when using native and GPIO CS")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191126164140.6240-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 4396393fb96449c56423fb4b351f76e45a6bcaf6 upstream.
In commit 0b8e7bbde5e7 ("drm/sun4i: tcon: Set min division of TCON0_DCLK
to 1.") it was assumed that all TCON variants support a minimum divider
of 1 if only DCLK was used.
However, the oldest generation of hardware only supports minimum divider
of 4 if only DCLK is used. If a divider of 1 was used on this old
hardware, some scrolling artifact would appear. A divider of 2 seemed
OK, but a divider of 3 had artifacts as well.
Set the minimum divider when outputing to parallel RGB based on the
hardware model, with a minimum of 4 for the oldest (A10/A10s/A13/A20)
hardware, and a minimum of 1 for the rest. A value is not set for the
TCON variants lacking channel 0.
This fixes the scrolling artifacts seen on my A13 tablet.
Fixes: 0b8e7bbde5e7 ("drm/sun4i: tcon: Set min division of TCON0_DCLK to 1.")
Cc: <stable@vger.kernel.org> # 5.4.x
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20200107070113.28951-1-wens@kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 67f96ff7c8f073648696eab50fd23ded23441067 upstream.
In Exynos542x/5800 SoCs, the G3D leaf clocks are located in the G3D power
domain. This is similar to the other hardware modules and their power
domains. However there is one thing specific to G3D clocks hierarchy.
Unlike other hardware modules, the G3D clocks hierarchy doesn't have any
gate clock between the TOP part of the hierarchy and the part located in
the power domain and some SoC internal busses are sourced directly from
the TOP muxes. The consequence of this design if the fact that the TOP
part of the hierarchy has to be enabled permanently to ensure proper
operation of the SoC power related components (G3D power domain and
Exynos Power Management Unit for system suspend/resume).
This patch adds an explicit call to clk_prepare_enable() on the last MUX
in the TOP part of G3D clock hierarchy to keep it enabled permanently to
ensure that the internal busses get their clock regardless of the main
G3D clock enablement status.
This fixes following imprecise abort issue observed on Odroid XU3/XU4
after enabling Panfrost driver by commit 1a5a85c56402 "ARM: dts: exynos:
Add Mali/GPU node on Exynos5420 and enable it on Odroid XU3/4"):
panfrost 11800000.gpu: clock rate = 400000000
panfrost 11800000.gpu: failed to get regulator: -517
panfrost 11800000.gpu: regulator init failed -517
Power domain G3D disable failed
...
panfrost 11800000.gpu: clock rate = 400000000
8<--- cut here ---
Unhandled fault: imprecise external abort (0x1406) at 0x00000000
pgd = (ptrval)
[00000000] *pgd=00000000
Internal error: : 1406 [#1] PREEMPT SMP ARM
Modules linked in:
CPU: 7 PID: 53 Comm: kworker/7:1 Not tainted 5.4.0-rc8-next-20191119-00032-g56f1001191a6 #6923
Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
Workqueue: events deferred_probe_work_func
PC is at panfrost_gpu_soft_reset+0x94/0x110
LR is at ___might_sleep+0x128/0x2dc
...
[<c05c231c>] (panfrost_gpu_soft_reset) from [<c05c2704>] (panfrost_gpu_init+0x10/0x67c)
[<c05c2704>] (panfrost_gpu_init) from [<c05c15d0>] (panfrost_device_init+0x158/0x2cc)
[<c05c15d0>] (panfrost_device_init) from [<c05c0cb0>] (panfrost_probe+0x80/0x178)
[<c05c0cb0>] (panfrost_probe) from [<c05cfaa0>] (platform_drv_probe+0x48/0x9c)
[<c05cfaa0>] (platform_drv_probe) from [<c05cd20c>] (really_probe+0x1c4/0x474)
[<c05cd20c>] (really_probe) from [<c05cd694>] (driver_probe_device+0x78/0x1bc)
[<c05cd694>] (driver_probe_device) from [<c05cb374>] (bus_for_each_drv+0x74/0xb8)
[<c05cb374>] (bus_for_each_drv) from [<c05ccfa8>] (__device_attach+0xd4/0x16c)
[<c05ccfa8>] (__device_attach) from [<c05cc110>] (bus_probe_device+0x88/0x90)
[<c05cc110>] (bus_probe_device) from [<c05cc634>] (deferred_probe_work_func+0x4c/0xd0)
[<c05cc634>] (deferred_probe_work_func) from [<c0149df0>] (process_one_work+0x300/0x864)
[<c0149df0>] (process_one_work) from [<c014a3ac>] (worker_thread+0x58/0x5a0)
[<c014a3ac>] (worker_thread) from [<c0151174>] (kthread+0x12c/0x160)
[<c0151174>] (kthread) from [<c01010b4>] (ret_from_fork+0x14/0x20)
Exception stack(0xee03dfb0 to 0xee03dff8)
...
Code: e594300c e5933020 e3130c01 1a00000f (ebefff50).
---[ end trace badde2b74a65a540 ]---
In the above case, the Panfrost driver disables G3D clocks after failure
of getting the needed regulator and return with -EPROVE_DEFER code. This
causes G3D power domain disable failure and then, during second probe
an imprecise abort is triggered due to undefined power domain state.
Fixes: 45f10dabb56b ("clk: samsung: exynos5420: Add SET_RATE_PARENT flag to clocks on G3D path")
Fixes: c9f7567aff31 ("clk: samsung: exynos542x: Move G3D subsystem clocks to its sub-CMU")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lkml.kernel.org/r/20191216131407.17225-1-m.szyprowski@samsung.com
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit cc90bc68422318eb8e75b15cd74bc8d538a7df29 upstream.
This partially reverts commit e3a5d8e386c3fb973fa75f2403622a8f3640ec06.
Commit e3a5d8e386c3 ("check bi_size overflow before merge") adds a bio_full
check to __bio_try_merge_page. This will cause __bio_try_merge_page to fail
when the last bi_io_vec has been reached. Instead, what we want here is only
the bi_size overflow check.
Fixes: e3a5d8e386c3 ("block: check bi_size overflow before merge")
Cc: stable@vger.kernel.org # v5.4+
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 16214bd9e43a31683a7073664b000029bba00354 upstream.
The following warning from the refcount framework is seen during ghes
initialization:
EDAC MC0: Giving out device to module ghes_edac.c controller ghes_edac: DEV ghes (INTERRUPT)
------------[ cut here ]------------
refcount_t: increment on 0; use-after-free.
WARNING: CPU: 36 PID: 1 at lib/refcount.c:156 refcount_inc_checked
[...]
Call trace:
refcount_inc_checked
ghes_edac_register
ghes_probe
...
It warns if the refcount is incremented from zero. This warning is
reasonable as a kernel object is typically created with a refcount of
one and freed once the refcount is zero. Afterwards the object would be
"used-after-free".
For GHES, the refcount is initialized with zero, and that is why this
message is seen when initializing the first instance. However, whenever
the refcount is zero, the device will be allocated and registered. Since
the ghes_reg_mutex protects the refcount and serializes allocation and
freeing of ghes devices, a use-after-free cannot happen here.
Instead of using refcount_inc() for the first instance, use
refcount_set(). This can be used here because the refcount is zero at
this point and can not change due to its protection by the mutex.
Fixes: 23f61b9fc5cc ("EDAC/ghes: Fix locking and memory barrier issues")
Reported-by: John Garry <john.garry@huawei.com>
Signed-off-by: Robert Richter <rrichter@marvell.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Tested-by: John Garry <john.garry@huawei.com>
Cc: <huangming23@huawei.com>
Cc: James Morse <james.morse@arm.com>
Cc: <linuxarm@huawei.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: <tanxiaofei@huawei.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: <wanghuiqiang@huawei.com>
Link: https://lkml.kernel.org/r/20191121213628.21244-1-rrichter@marvell.com
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 6fd739c04ffd877641b01371f9fde67901e7f9cb upstream.
The commit e38e486d66e2 ("ALSA: hda: Modify stream stripe mask only
when needed") tried to address the regression by the unconditional
application of the stripe mask, but this caused yet another
regression for the previously working devices. Namely, the patch
clears the azx_dev->stripe flag at snd_hdac_stream_clear(), but this
may be called multiple times before restarting the stream, so this
ended up with clearance of the flag for the whole time.
This patch fixes the regression by moving the azx_dev->stripe flag
clearance at the counter-part, the close callback of HDMI codec
driver instead.
Fixes: e38e486d66e2 ("ALSA: hda: Modify stream stripe mask only when needed")
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=205855
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=204477
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191214175217.31852-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
There's an issue with deferred requests through drain, where if we do
need to defer, we're not copying over the sqe_submit state correctly.
This can result in using uninitialized data when we then later go and
submit the deferred request, like this check in __io_submit_sqe():
if (unlikely(s->index >= ctx->sq_entries))
return -EINVAL;
with 's' being uninitialized, we can randomly fail this check. Fix this
by copying sqe_submit state when we defer a request.
Because it was fixed as part of a cleanup series in mainline, before
anyone realized we had this issue. That removed the separate states
of ->index vs ->submit.sqe. That series is not something I was
comfortable putting into stable, hence the much simpler addition.
Here's the patch in the series that fixes the same issue:
commit cf6fd4bd559ee61a4454b161863c8de6f30f8dca
Author: Pavel Begunkov <asml.silence@gmail.com>
Date: Mon Nov 25 23:14:39 2019 +0300
io_uring: inline struct sqe_submit
Reported-by: Andres Freund <andres@anarazel.de>
Reported-by: Tomáš Chaloupka
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
In the implementation of psxpad_spi_probe() the allocated memory for
pdev is leaked if psxpad_spi_init_ff() or input_register_polled_device()
fail. The solution is using device managed allocation, like the one used
for pad. Perform the allocation using
devm_input_allocate_polled_device().
Fixes: 8be193c7b1f4 ("Input: add support for PlayStation 1/2 joypads connected via SPI")
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit a7d0358ea3b7f8d7216e663c1ae71cabf7ac24e3 upstream.
Apply same logic to pin setup as on previous platforms. Fixes
errors in HDMI/DP playback.
Tested with both snd-hda-intel and SOF drivers.
Fixes: 9a11ba7388f1 ("ALSA: hda: hdmi - add Tigerlake support")
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20191111133838.21213-1-kai.vehmanen@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 23f61b9fc5cc10d87f66e50518707eec2a0fbda1 upstream.
The ghes registration and refcount is broken in several ways:
* ghes_edac_register() returns with success for a 2nd instance
even if a first instance's registration is still running. This is
not correct as the first instance may fail later. A subsequent
registration may not finish before the first. Parallel registrations
must be avoided.
* The refcount was increased even if a registration failed. This
leads to stale counters preventing the device from being released.
* The ghes refcount may not be decremented properly on unregistration.
Always decrement the refcount once ghes_edac_unregister() is called to
keep the refcount sane.
* The ghes_pvt pointer is handed to the irq handler before registration
finished.
* The mci structure could be freed while the irq handler is running.
Fix this by adding a mutex to ghes_edac_register(). This mutex
serializes instances to register and unregister. The refcount is only
increased if the registration succeeded. This makes sure the refcount is
in a consistent state after registering or unregistering a device.
Note: A spinlock cannot be used here as the code section may sleep.
The ghes_pvt is protected by ghes_lock now. This ensures the pointer is
not updated before registration was finished or while the irq handler is
running. It is unset before unregistering the device including necessary
(implicit) memory barriers making the changes visible to other CPUs.
Thus, the device can not be used anymore by an interrupt.
Also, rename ghes_init to ghes_refcount for better readability and
switch to refcount API.
A refcount is needed because there can be multiple GHES structures being
defined (see ACPI 6.3 specification, 18.3.2.7 Generic Hardware Error
Source, "Some platforms may describe multiple Generic Hardware Error
Source structures with different notification types, ...").
Another approach to use the mci's device refcount (get_device()) and
have a release function does not work here. A release function will be
called only for device_release() with the last put_device() call. The
device must be deleted *before* that with device_del(). This is only
possible by maintaining an own refcount.
[ bp: touchups. ]
Fixes: 0fe5f281f749 ("EDAC, ghes: Model a single, logical memory controller")
Fixes: 1e72e673b9d1 ("EDAC/ghes: Fix Use after free in ghes_edac remove path")
Co-developed-by: James Morse <james.morse@arm.com>
Signed-off-by: James Morse <james.morse@arm.com>
Co-developed-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Robert Richter <rrichter@marvell.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: "linux-edac@vger.kernel.org" <linux-edac@vger.kernel.org>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Tony Luck <tony.luck@intel.com>
Link: https://lkml.kernel.org/r/20191105200732.3053-1-rrichter@marvell.com
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit c04571251b3d842096f1597f5d4badb508be016d upstream.
The ast2600 no longer uses bit 4 in the control register to indicate a
1MHz clock (It now controls whether this watchdog is reset by a SOC
reset). This means we do not want to set it. It also does not need to be
set for the ast2500, as it is read-only on that SoC.
The comment next to the clock rate selection wandered away from where it
was set, so put it back next to the register setting it's describing.
Fixes: b3528b487448 ("watchdog: aspeed: Add support for AST2600")
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20191108032905.22463-1-joel@jms.id.au
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit e3fc3f3d0943b126f76b8533960e4168412d9e5a upstream.
The first argument to WARN() is supposed to be a condition. The
original code will just print the mdname() instead of the full warning
message.
Fixes: c84a1372df92 ("md/raid0: avoid RAID0 data corruption due to layout confusion.")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit ca58f55108fee41d87c9123f85ad4863e5de7f45 upstream.
This is an alternative fix attemp for the issue reported in the commit
caa8422d01e9 ("ALSA: hda: Flush interrupts on disabling") that was
reverted later due to regressions. Instead of tweaking the hardware
disablement order and the enforced irq flushing, do calling
cancel_work_sync() of the unsol work early enough, and explicitly
ignore the unsol events during the shutdown by checking the
bus->shutdown flag.
Fixes: caa8422d01e9 ("ALSA: hda: Flush interrupts on disabling")
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://lore.kernel.org/r/s5h1ruxt9cz.wl-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 433f4ba1904100da65a311033f17a9bf586b287e upstream.
The bounds check was present in KVM_GET_SUPPORTED_CPUID but not
KVM_GET_EMULATED_CPUID.
Reported-by: syzbot+e3f4897236c4eeb8af4f@syzkaller.appspotmail.com
Fixes: 84cffe499b94 ("kvm: Emulate MOVBE", 2013-10-29)
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 2a9edd056ed4fbf9d2e797c3fc06335af35bccc4 upstream.
The old loop wouldn't stop when reaching `start` if `start==NULL`, instead
continuing backwards to index -1 and crashing.
Luckily you need to be highly privileged to map things at NULL, so it's not
a big problem.
Fix it by adjusting the loop so that the loop variable is always in bounds.
This patch is deliberately minimal to simplify backporting, but IMO this
function could use a refactor. The jump labels in the second loop body are
horrible (the error gotos should be jumping to free_range instead), and
both loops would look nicer if they just iterated upwards through indices.
And the up_read()+mmput() shouldn't be duplicated like that.
Cc: stable@vger.kernel.org
Fixes: 457b9a6f09f0 ("Staging: android: add binder driver")
Signed-off-by: Jann Horn <jannh@google.com>
Acked-by: Christian Brauner <christian.brauner@ubuntu.com>
Link: https://lore.kernel.org/r/20191018205631.248274-3-jannh@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit a7a74d7ff55a0c657bc46238b050460b9eacea95 upstream.
binder_alloc_mmap_handler() attempts to detect the use of ->mmap() on a
binder_proc whose binder_alloc has already been initialized by checking
whether alloc->buffer is non-zero.
Before commit 880211667b20 ("binder: remove kernel vm_area for buffer
space"), alloc->buffer was a kernel mapping address, which is always
non-zero, but since that commit, it is a userspace mapping address.
A sufficiently privileged user can map /dev/binder at NULL, tricking
binder_alloc_mmap_handler() into assuming that the binder_proc has not been
mapped yet. This leads to memory unsafety.
Luckily, no context on Android has such privileges, and on a typical Linux
desktop system, you need to be root to do that.
Fix it by using the mapping size instead of the mapping address to
distinguish the mapped case. A valid VMA can't have size zero.
Fixes: 880211667b20 ("binder: remove kernel vm_area for buffer space")
Cc: stable@vger.kernel.org
Signed-off-by: Jann Horn <jannh@google.com>
Acked-by: Christian Brauner <christian.brauner@ubuntu.com>
Link: https://lore.kernel.org/r/20191018205631.248274-2-jannh@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 8eb52a1ee37aafd9b796713aa0b3ab9cbc455be3 upstream.
binder_alloc_print_pages() iterates over
alloc->pages[0..alloc->buffer_size-1] under alloc->mutex.
binder_alloc_mmap_handler() writes alloc->pages and alloc->buffer_size
without holding that lock, and even writes them before the last bailout
point.
Unfortunately we can't take the alloc->mutex in the ->mmap() handler
because mmap_sem can be taken while alloc->mutex is held.
So instead, we have to locklessly check whether the binder_alloc has been
fully initialized with binder_alloc_get_vma(), like in
binder_alloc_new_buf_locked().
Fixes: 8ef4665aa129 ("android: binder: Add page usage in binder stats")
Cc: stable@vger.kernel.org
Signed-off-by: Jann Horn <jannh@google.com>
Acked-by: Christian Brauner <christian.brauner@ubuntu.com>
Link: https://lore.kernel.org/r/20191018205631.248274-1-jannh@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 163b00cde7cf2206e248789d2780121ad5e6a70b upstream.
1851799e1d29 ("thermal: Fix use-after-free when unregistering thermal zone
device") changed cancel_delayed_work to cancel_delayed_work_sync to avoid
a use-after-free issue. However, cancel_delayed_work_sync could be called
insides the WQ causing deadlock.
[54109.642398] c0 1162 kworker/u17:1 D 0 11030 2 0x00000000
[54109.642437] c0 1162 Workqueue: thermal_passive_wq thermal_zone_device_check
[54109.642447] c0 1162 Call trace:
[54109.642456] c0 1162 __switch_to+0x138/0x158
[54109.642467] c0 1162 __schedule+0xba4/0x1434
[54109.642480] c0 1162 schedule_timeout+0xa0/0xb28
[54109.642492] c0 1162 wait_for_common+0x138/0x2e8
[54109.642511] c0 1162 flush_work+0x348/0x40c
[54109.642522] c0 1162 __cancel_work_timer+0x180/0x218
[54109.642544] c0 1162 handle_thermal_trip+0x2c4/0x5a4
[54109.642553] c0 1162 thermal_zone_device_update+0x1b4/0x25c
[54109.642563] c0 1162 thermal_zone_device_check+0x18/0x24
[54109.642574] c0 1162 process_one_work+0x3cc/0x69c
[54109.642583] c0 1162 worker_thread+0x49c/0x7c0
[54109.642593] c0 1162 kthread+0x17c/0x1b0
[54109.642602] c0 1162 ret_from_fork+0x10/0x18
[54109.643051] c0 1162 kworker/u17:2 D 0 16245 2 0x00000000
[54109.643067] c0 1162 Workqueue: thermal_passive_wq thermal_zone_device_check
[54109.643077] c0 1162 Call trace:
[54109.643085] c0 1162 __switch_to+0x138/0x158
[54109.643095] c0 1162 __schedule+0xba4/0x1434
[54109.643104] c0 1162 schedule_timeout+0xa0/0xb28
[54109.643114] c0 1162 wait_for_common+0x138/0x2e8
[54109.643122] c0 1162 flush_work+0x348/0x40c
[54109.643131] c0 1162 __cancel_work_timer+0x180/0x218
[54109.643141] c0 1162 handle_thermal_trip+0x2c4/0x5a4
[54109.643150] c0 1162 thermal_zone_device_update+0x1b4/0x25c
[54109.643159] c0 1162 thermal_zone_device_check+0x18/0x24
[54109.643167] c0 1162 process_one_work+0x3cc/0x69c
[54109.643177] c0 1162 worker_thread+0x49c/0x7c0
[54109.643186] c0 1162 kthread+0x17c/0x1b0
[54109.643195] c0 1162 ret_from_fork+0x10/0x18
[54109.644500] c0 1162 cat D 0 7766 1 0x00000001
[54109.644515] c0 1162 Call trace:
[54109.644524] c0 1162 __switch_to+0x138/0x158
[54109.644536] c0 1162 __schedule+0xba4/0x1434
[54109.644546] c0 1162 schedule_preempt_disabled+0x80/0xb0
[54109.644555] c0 1162 __mutex_lock+0x3a8/0x7f0
[54109.644563] c0 1162 __mutex_lock_slowpath+0x14/0x20
[54109.644575] c0 1162 thermal_zone_get_temp+0x84/0x360
[54109.644586] c0 1162 temp_show+0x30/0x78
[54109.644609] c0 1162 dev_attr_show+0x5c/0xf0
[54109.644628] c0 1162 sysfs_kf_seq_show+0xcc/0x1a4
[54109.644636] c0 1162 kernfs_seq_show+0x48/0x88
[54109.644656] c0 1162 seq_read+0x1f4/0x73c
[54109.644664] c0 1162 kernfs_fop_read+0x84/0x318
[54109.644683] c0 1162 __vfs_read+0x50/0x1bc
[54109.644692] c0 1162 vfs_read+0xa4/0x140
[54109.644701] c0 1162 SyS_read+0xbc/0x144
[54109.644708] c0 1162 el0_svc_naked+0x34/0x38
[54109.845800] c0 1162 D 720.000s 1->7766->7766 cat [panic]
Fixes: 1851799e1d29 ("thermal: Fix use-after-free when unregistering thermal zone device")
Cc: stable@vger.kernel.org
Signed-off-by: Wei Wang <wvw@google.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 419e9c38aa075ed0cd3c13d47e15954b686bcdb6 upstream.
When splicing using iomap_dio_rw() to a pipe, we may leak pipe pages
because bio_iov_iter_get_pages() records that the pipe will have full
extent worth of data however if file size is not block size aligned
iomap_dio_rw() returns less than what bio_iov_iter_get_pages() set up
and splice code gets confused leaking a pipe page with the file tail.
Handle the situation similarly to the old direct IO implementation and
revert iter to actually returned read amount which makes iter consistent
with value returned from iomap_dio_rw() and thus the splice code is
happy.
Fixes: ff6a9292e6f6 ("iomap: implement direct I/O")
CC: stable@vger.kernel.org
Reported-by: syzbot+991400e8eba7e00a26e1@syzkaller.appspotmail.com
Signed-off-by: Jan Kara <jack@suse.cz>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 7ee23491b39259ae83899dd93b2a29ef0f22f0a7 upstream.
The permissions of the read-only or write-only sysfs files can be
changed (as root) and the user can then try to read a write-only file or
write to a read-only file which will lead to kernel crash here.
Protect against that by always validating the show/store callbacks.
Link: https://lore.kernel.org/r/d45cc26361a174ae12dbb86c994ef334d257924b.1573096807.git.viresh.kumar@linaro.org
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 870db5d1015c8bd63e93b579e857223c96249ff7 upstream.
USB completion handlers are called in atomic context and must
specifically not allocate memory using GFP_KERNEL.
Fixes: 9f2d3eae88d2 ("can: ucan: add driver for Theobroma Systems UCAN devices")
Cc: stable <stable@vger.kernel.org> # 4.19
Cc: Jakob Unterwurzacher <jakob.unterwurzacher@theobroma-systems.com>
Cc: Martin Elshuber <martin.elshuber@theobroma-systems.com>
Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 15f794bd977a0135328fbdd8a83cc64c1d267b39 upstream.
Even if the flag use_gpio_descriptors is set, it is possible that
cs_gpiods was not allocated, which leads to a kernel crash.
Reported-by: "kernelci.org bot" <bot@kernelci.org>
Fixes: 3e5ec1db8bfe ("spi: Fix SPI_CS_HIGH setting when using native and GPIO CS")
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20191024141309.22434-1-gregory.clement@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 3e5ec1db8bfee845d9f8560d1c64aeaccd586398 upstream.
When improving the CS GPIO support at core level, the SPI_CS_HIGH
has been enabled for all the CS lines used for a given SPI controller.
However, the SPI framework allows to have on the same controller native
CS and GPIO CS. The native CS may not support the SPI_CS_HIGH, so they
should not be setup automatically.
With this patch the setting is done only for the CS that will use a
GPIO as CS
Fixes: f3186dd87669 ("spi: Optionally use GPIO descriptors for CS GPIOs")
Cc: <stable@vger.kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20191018152929.3287-1-gregory.clement@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 7cbb16b2122c09f2ae393a1542fed628505b9da6 upstream.
Until a few years ago, this driver was only used with CS GPIO. The
only exception is CS0 on AT91RM9200 which has to use internal CS. A
limitation of the internal CS is that they don't support CS High.
So by using the CS GPIO the CS high configuration was available except
for the particular case CS0 on RM9200.
When the support for the internal chip-select was added, the check of
the CS high support was not updated. Due to this the driver accepts
this configuration for all the SPI controller v2 (used by all SoCs
excepting the AT91RM9200) whereas the hardware doesn't support it for
infernal CS.
This patch fixes the test to match the hardware capabilities.
Fixes: 4820303480a1 ("spi: atmel: add support for the internal chip-select of the spi controller")
Cc: <stable@vger.kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20191017141846.7523-3-gregory.clement@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 3c0af1dd2fe78adc02fe21f6cfe7d6cb8602573e upstream.
spi_master_put() must only be called in .probe() in case of error.
As devm_spi_register_master() is used during probe, spi_master_put()
mustn't be called in .remove() callback.
It fixes the following kernel WARNING/Oops when executing
echo "58003000.spi" > /sys/bus/platform/drivers/stm32-qspi/unbind :
------------[ cut here ]------------
WARNING: CPU: 1 PID: 496 at fs/kernfs/dir.c:1504 kernfs_remove_by_name_ns+0x9c/0xa4
kernfs: can not remove 'uevent', no directory
Modules linked in:
CPU: 1 PID: 496 Comm: sh Not tainted 5.3.0-rc1-00219-ga0e07bb51a37 #62
Hardware name: STM32 (Device Tree Support)
[<c0111570>] (unwind_backtrace) from [<c010d384>] (show_stack+0x10/0x14)
[<c010d384>] (show_stack) from [<c08db558>] (dump_stack+0xb4/0xc8)
[<c08db558>] (dump_stack) from [<c01209d8>] (__warn.part.3+0xbc/0xd8)
[<c01209d8>] (__warn.part.3) from [<c0120a5c>] (warn_slowpath_fmt+0x68/0x8c)
[<c0120a5c>] (warn_slowpath_fmt) from [<c02e5844>] (kernfs_remove_by_name_ns+0x9c/0xa4)
[<c02e5844>] (kernfs_remove_by_name_ns) from [<c05833a4>] (device_del+0x128/0x358)
[<c05833a4>] (device_del) from [<c05835f8>] (device_unregister+0x24/0x64)
[<c05835f8>] (device_unregister) from [<c0638dac>] (spi_unregister_controller+0x88/0xe8)
[<c0638dac>] (spi_unregister_controller) from [<c058c580>] (release_nodes+0x1bc/0x200)
[<c058c580>] (release_nodes) from [<c0588a44>] (device_release_driver_internal+0xec/0x1ac)
[<c0588a44>] (device_release_driver_internal) from [<c0586840>] (unbind_store+0x60/0xd4)
[<c0586840>] (unbind_store) from [<c02e64e8>] (kernfs_fop_write+0xe8/0x1c4)
[<c02e64e8>] (kernfs_fop_write) from [<c0266b44>] (__vfs_write+0x2c/0x1c0)
[<c0266b44>] (__vfs_write) from [<c02694c0>] (vfs_write+0xa4/0x184)
[<c02694c0>] (vfs_write) from [<c0269710>] (ksys_write+0x58/0xd0)
[<c0269710>] (ksys_write) from [<c0101000>] (ret_fast_syscall+0x0/0x54)
Exception stack(0xdd289fa8 to 0xdd289ff0)
9fa0: 0000006c 000e20e8 00000001 000e20e8 0000000d 00000000
9fc0: 0000006c 000e20e8 b6f87da0 00000004 0000000d 0000000d 00000000 00000000
9fe0: 00000004 bee639b0 b6f2286b b6eaf6c6
---[ end trace 1b15df8a02d76aef ]---
------------[ cut here ]------------
WARNING: CPU: 1 PID: 496 at fs/kernfs/dir.c:1504 kernfs_remove_by_name_ns+0x9c/0xa4
kernfs: can not remove 'online', no directory
Modules linked in:
CPU: 1 PID: 496 Comm: sh Tainted: G W 5.3.0-rc1-00219-ga0e07bb51a37 #62
Hardware name: STM32 (Device Tree Support)
[<c0111570>] (unwind_backtrace) from [<c010d384>] (show_stack+0x10/0x14)
[<c010d384>] (show_stack) from [<c08db558>] (dump_stack+0xb4/0xc8)
[<c08db558>] (dump_stack) from [<c01209d8>] (__warn.part.3+0xbc/0xd8)
[<c01209d8>] (__warn.part.3) from [<c0120a5c>] (warn_slowpath_fmt+0x68/0x8c)
[<c0120a5c>] (warn_slowpath_fmt) from [<c02e5844>] (kernfs_remove_by_name_ns+0x9c/0xa4)
[<c02e5844>] (kernfs_remove_by_name_ns) from [<c0582488>] (device_remove_attrs+0x20/0x5c)
[<c0582488>] (device_remove_attrs) from [<c05833b0>] (device_del+0x134/0x358)
[<c05833b0>] (device_del) from [<c05835f8>] (device_unregister+0x24/0x64)
[<c05835f8>] (device_unregister) from [<c0638dac>] (spi_unregister_controller+0x88/0xe8)
[<c0638dac>] (spi_unregister_controller) from [<c058c580>] (release_nodes+0x1bc/0x200)
[<c058c580>] (release_nodes) from [<c0588a44>] (device_release_driver_internal+0xec/0x1ac)
[<c0588a44>] (device_release_driver_internal) from [<c0586840>] (unbind_store+0x60/0xd4)
[<c0586840>] (unbind_store) from [<c02e64e8>] (kernfs_fop_write+0xe8/0x1c4)
[<c02e64e8>] (kernfs_fop_write) from [<c0266b44>] (__vfs_write+0x2c/0x1c0)
[<c0266b44>] (__vfs_write) from [<c02694c0>] (vfs_write+0xa4/0x184)
[<c02694c0>] (vfs_write) from [<c0269710>] (ksys_write+0x58/0xd0)
[<c0269710>] (ksys_write) from [<c0101000>] (ret_fast_syscall+0x0/0x54)
Exception stack(0xdd289fa8 to 0xdd289ff0)
9fa0: 0000006c 000e20e8 00000001 000e20e8 0000000d 00000000
9fc0: 0000006c 000e20e8 b6f87da0 00000004 0000000d 0000000d 00000000 00000000
9fe0: 00000004 bee639b0 b6f2286b b6eaf6c6
---[ end trace 1b15df8a02d76af0 ]---
8<--- cut here ---
Unable to handle kernel NULL pointer dereference at virtual address 00000050
pgd = e612f14d
[00000050] *pgd=ff1f5835
Internal error: Oops: 17 [#1] SMP ARM
Modules linked in:
CPU: 1 PID: 496 Comm: sh Tainted: G W 5.3.0-rc1-00219-ga0e07bb51a37 #62
Hardware name: STM32 (Device Tree Support)
PC is at kernfs_find_ns+0x8/0xfc
LR is at kernfs_find_and_get_ns+0x30/0x48
pc : [<c02e49a4>] lr : [<c02e4ac8>] psr: 40010013
sp : dd289dac ip : 00000000 fp : 00000000
r10: 00000000 r9 : def6ec58 r8 : dd289e54
r7 : 00000000 r6 : c0abb234 r5 : 00000000 r4 : c0d26a30
r3 : ddab5080 r2 : 00000000 r1 : c0abb234 r0 : 00000000
Flags: nZcv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none
Control: 10c5387d Table: dd11c06a DAC: 00000051
Process sh (pid: 496, stack limit = 0xe13a592d)
Stack: (0xdd289dac to 0xdd28a000)
9da0: c0d26a30 00000000 c0abb234 00000000 c02e4ac8
9dc0: 00000000 c0976b44 def6ec00 dea53810 dd289e54 c02e864c c0a61a48 c0a4a5ec
9de0: c0d630a8 def6ec00 c0d04c48 c02e86e0 def6ec00 de909338 c0d04c48 c05833b0
9e00: 00000000 c0638144 dd289e54 def59900 00000000 475b3ee5 def6ec00 00000000
9e20: def6ec00 def59b80 dd289e54 def59900 00000000 c05835f8 def6ec00 c0638dac
9e40: 0000000a dea53810 c0d04c48 c058c580 dea53810 def59500 def59b80 475b3ee5
9e60: ddc63e00 dea53810 dea3fe10 c0d63a0c dea53810 ddc63e00 dd289f78 dd240d10
9e80: 00000000 c0588a44 c0d59a20 0000000d c0d63a0c c0586840 0000000d dd240d00
9ea0: 00000000 00000000 ddc63e00 c02e64e8 00000000 00000000 c0d04c48 dd9bbcc0
9ec0: c02e6400 dd289f78 00000000 000e20e8 0000000d c0266b44 00000055 00000cc0
9ee0: 000000e3 000e3000 dd11c000 dd11c000 00000000 00000000 00000000 00000000
9f00: ffeee38c dff99688 00000000 475b3ee5 00000001 dd289fb0 ddab5080 ddaa5800
9f20: 00000817 000e30ec dd9e7720 475b3ee5 ddaa583c 0000000d dd9bbcc0 000e20e8
9f40: dd289f78 00000000 000e20e8 0000000d 00000000 c02694c0 00000000 00000000
9f60: c0d04c48 dd9bbcc0 00000000 00000000 dd9bbcc0 c0269710 00000000 00000000
9f80: 000a91f4 475b3ee5 0000006c 000e20e8 b6f87da0 00000004 c0101204 dd288000
9fa0: 00000004 c0101000 0000006c 000e20e8 00000001 000e20e8 0000000d 00000000
9fc0: 0000006c 000e20e8 b6f87da0 00000004 0000000d 0000000d 00000000 00000000
9fe0: 00000004 bee639b0 b6f2286b b6eaf6c6 600e0030 00000001 00000000 00000000
[<c02e49a4>] (kernfs_find_ns) from [<def6ec00>] (0xdef6ec00)
Code: ebf8eeab c0dc50b8 e92d40f0 e292c000 (e1d035b0)
---[ end trace 1b15df8a02d76af1 ]---
Fixes: a88eceb17ac7 ("spi: stm32-qspi: add spi_master_put in release function")
Cc: <stable@vger.kernel.org>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Link: https://lore.kernel.org/r/20191004123606.17241-1-patrice.chotard@st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit f6910679e17ad4915f008bd2c614d38052426f7c upstream.
Later versions of the QSPI controller (e.g. in i.MX6UL/ULL and i.MX7)
seem to have an additional TDH setting in the FLSHCR register, that
needs to be set in accordance with the access mode that is used (DDR
or SDR).
Previous bootstages such as BootROM or bootloader might have used the
DDR mode to access the flash. As we currently only use SDR mode, we
need to make sure the TDH bits are cleared upon initialization.
Fixes: 84d043185dbe ("spi: Add a driver for the Freescale/NXP QuadSPI controller")
Cc: <stable@vger.kernel.org>
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Acked-by: Han Xu <han.xu@nxp.com>
Link: https://lore.kernel.org/r/20191007071933.26786-1-frieder.schrempf@kontron.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit d6b197a14863818a7ed7890e91f043fab49e8c60 upstream.
The RX FIFO should be 128 byte rather than 512 byte. It's a typo on
reference manual.
Signed-off-by: Han Xu <han.xu@nxp.com>
Link: https://lore.kernel.org/r/20190710023128.13115-3-han.xu@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit f398243e9fd6a3a059c1ea7b380c40628dbf0c61 upstream.
The elliptic curve arithmetic library used by the EC-DH KPP implementation
assumes big endian byte order, and unconditionally reverses the byte
and word order of multi-limb quantities. On big endian systems, the byte
reordering is not necessary, while the word ordering needs to be retained.
So replace the __swab64() invocation with a call to be64_to_cpu() which
should do the right thing for both little and big endian builds.
Fixes: 3c4b23901a0c ("crypto: ecdh - Add ECDH software support")
Cc: <stable@vger.kernel.org> # v4.9+
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 691505a803a7f223b2af621848d581259c61f77d upstream.
A NULL-pointer dereference was reported in fedora bz#1762199 while
reshaping a raid6 array after adding a fifth drive to an existing
array.
[ 47.343549] md/raid:md0: raid level 6 active with 3 out of 5 devices, algorithm 2
[ 47.804017] md0: detected capacity change from 0 to 7885289422848
[ 47.822083] Unable to handle kernel read from unreadable memory at virtual address 0000000000000000
...
[ 47.940477] CPU: 1 PID: 14210 Comm: md0_raid6 Tainted: G W 5.2.18-200.fc30.aarch64 #1
[ 47.949594] Hardware name: AMD Overdrive/Supercharger/To be filled by O.E.M., BIOS ROD1002C 04/08/2016
[ 47.958886] pstate: 00400085 (nzcv daIf +PAN -UAO)
[ 47.963668] pc : __list_del_entry_valid+0x2c/0xa8
[ 47.968366] lr : ccp_tx_submit+0x84/0x168 [ccp]
[ 47.972882] sp : ffff00001369b970
[ 47.976184] x29: ffff00001369b970 x28: ffff00001369bdb8
[ 47.981483] x27: 00000000ffffffff x26: ffff8003b758af70
[ 47.986782] x25: ffff8003b758b2d8 x24: ffff8003e6245818
[ 47.992080] x23: 0000000000000000 x22: ffff8003e62450c0
[ 47.997379] x21: ffff8003dfd6add8 x20: 0000000000000003
[ 48.002678] x19: ffff8003e6245100 x18: 0000000000000000
[ 48.007976] x17: 0000000000000000 x16: 0000000000000000
[ 48.013274] x15: 0000000000000000 x14: 0000000000000000
[ 48.018572] x13: ffff7e000ef83a00 x12: 0000000000000001
[ 48.023870] x11: ffff000010eff998 x10: 00000000000019a0
[ 48.029169] x9 : 0000000000000000 x8 : ffff8003e6245180
[ 48.034467] x7 : 0000000000000000 x6 : 000000000000003f
[ 48.039766] x5 : 0000000000000040 x4 : ffff8003e0145080
[ 48.045064] x3 : dead000000000200 x2 : 0000000000000000
[ 48.050362] x1 : 0000000000000000 x0 : ffff8003e62450c0
[ 48.055660] Call trace:
[ 48.058095] __list_del_entry_valid+0x2c/0xa8
[ 48.062442] ccp_tx_submit+0x84/0x168 [ccp]
[ 48.066615] async_tx_submit+0x224/0x368 [async_tx]
[ 48.071480] async_trigger_callback+0x68/0xfc [async_tx]
[ 48.076784] ops_run_biofill+0x178/0x1e8 [raid456]
[ 48.081566] raid_run_ops+0x248/0x818 [raid456]
[ 48.086086] handle_stripe+0x864/0x1208 [raid456]
[ 48.090781] handle_active_stripes.isra.0+0xb0/0x278 [raid456]
[ 48.096604] raid5d+0x378/0x618 [raid456]
[ 48.100602] md_thread+0xa0/0x150
[ 48.103905] kthread+0x104/0x130
[ 48.107122] ret_from_fork+0x10/0x18
[ 48.110686] Code: d2804003 f2fbd5a3 eb03003f 54000320 (f9400021)
[ 48.116766] ---[ end trace 23f390a527f7ad77 ]---
ccp_tx_submit is passed a dma_async_tx_descriptor which is contained in
a ccp_dma_desc and adds it to a ccp channel's pending list:
list_del(&desc->entry);
list_add_tail(&desc->entry, &chan->pending);
The problem is that desc->entry may be uninitialized in the
async_trigger_callback path where the descriptor was gotten
from ccp_prep_dma_interrupt which got it from ccp_alloc_dma_desc
which doesn't initialize the desc->entry list head. So, just
initialize the list head to avoid the problem.
Cc: <stable@vger.kernel.org>
Reported-by: Sahaj Sarup <sahajsarup@gmail.com>
Signed-off-by: Mark Salter <msalter@redhat.com>
Acked-by: Gary R Hook <gary.hook@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 504582e8e40b90b8f8c58783e2d1e4f6a2b71a3a upstream.
Commit 79c65d179a40e145 ("crypto: cbc - Convert to skcipher") updated
the generic CBC template wrapper from a blkcipher to a skcipher algo,
to get away from the deprecated blkcipher interface. However, as a side
effect, drivers that instantiate CBC transforms using the blkcipher as
a fallback no longer work, since skciphers can wrap blkciphers but not
the other way around. This broke the geode-aes driver.
So let's fix it by moving to the sync skcipher interface when allocating
the fallback. At the same time, align with the generic API for ECB and
CBC by rejecting inputs that are not a multiple of the AES block size.
Fixes: 79c65d179a40e145 ("crypto: cbc - Convert to skcipher")
Cc: <stable@vger.kernel.org> # v4.20+ ONLY
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Florian Bezdeka <florian@bezdeka.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 64e7f852c47ce99f6c324c46d6a299a5a7ebead9 upstream.
when libkcapi test is executed using HW accelerator, cipher operation
return -74.Since af_alg_async_cb->ki_complete treat err as unsigned int,
libkcapi receive 429467222 even though it expect -ve value.
Hence its required to cast resultlen to int so that proper
error is returned to libkcapi.
AEAD one shot non-aligned test 2(libkcapi test)
./../bin/kcapi -x 10 -c "gcm(aes)" -i 7815d4b06ae50c9c56e87bd7
-k ea38ac0c9b9998c80e28fb496a2b88d9 -a
"853f98a750098bec1aa7497e979e78098155c877879556bb51ddeb6374cbaefc"
-t "c4ce58985b7203094be1d134c1b8ab0b" -q
"b03692f86d1b8b39baf2abb255197c98"
Fixes: d887c52d6ae4 ("crypto: algif_aead - overhaul memory management")
Cc: <stable@vger.kernel.org>
Signed-off-by: Ayush Sawal <ayush.sawal@chelsio.com>
Signed-off-by: Atul Gupta <atul.gupta@chelsio.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Ayush Sawal <ayush.sawal@chelsio.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 86ef1dfcb561473fbf5e199d58d18c55554d78be upstream.
commit 394a9e044702 ("crypto: cfb - add missing 'chunksize' property")
adds a test vector where the input length is smaller than the IV length
(the second test vector). This revealed a NULL pointer dereference in
the atmel-aes driver, that is caused by passing an incorrect offset in
scatterwalk_map_and_copy() when atmel_aes_complete() is called.
Do not save the IV in req->info of ablkcipher_request (or equivalently
req->iv of skcipher_request) when req->nbytes < ivsize, because the IV
will not be further used.
While touching the code, modify the type of ivsize from int to
unsigned int, to comply with the return type of
crypto_ablkcipher_ivsize().
Fixes: 91308019ecb4 ("crypto: atmel-aes - properly set IV after {en,de}crypt")
Cc: <stable@vger.kernel.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 746c908c4d72e49068ab216c3926d2720d71a90d upstream.
This patch fixes a crash that can happen during probe
when the available dma memory is not enough (this can
happen if the crypto4xx is built as a module).
The descriptor window mapping would end up being free'd
twice, once in crypto4xx_build_pdr() and the second time
in crypto4xx_destroy_sdr().
Fixes: 5d59ad6eea82 ("crypto: crypto4xx - fix crypto4xx_build_pdr, crypto4xx_build_sdr leak")
Cc: <stable@vger.kernel.org>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit ad5996d9a0e8019c3ae5151e687939369acfe044 upstream.
Acquire kvm->srcu for the duration of ->set_nested_state() to fix a bug
where nVMX derefences ->memslots without holding ->srcu or ->slots_lock.
The other half of nested migration, ->get_nested_state(), does not need
to acquire ->srcu as it is a purely a dump of internal KVM (and CPU)
state to userspace.
Detected as an RCU lockdep splat that is 100% reproducible by running
KVM's state_test selftest with CONFIG_PROVE_LOCKING=y. Note that the
failing function, kvm_is_visible_gfn(), is only checking the validity of
a gfn, it's not actually accessing guest memory (which is more or less
unsupported during vmx_set_nested_state() due to incorrect MMU state),
i.e. vmx_set_nested_state() itself isn't fundamentally broken. In any
case, setting nested state isn't a fast path so there's no reason to go
out of our way to avoid taking ->srcu.
=============================
WARNING: suspicious RCU usage
5.4.0-rc7+ #94 Not tainted
-----------------------------
include/linux/kvm_host.h:626 suspicious rcu_dereference_check() usage!
other info that might help us debug this:
rcu_scheduler_active = 2, debug_locks = 1
1 lock held by evmcs_test/10939:
#0: ffff88826ffcb800 (&vcpu->mutex){+.+.}, at: kvm_vcpu_ioctl+0x85/0x630 [kvm]
stack backtrace:
CPU: 1 PID: 10939 Comm: evmcs_test Not tainted 5.4.0-rc7+ #94
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 0.0.0 02/06/2015
Call Trace:
dump_stack+0x68/0x9b
kvm_is_visible_gfn+0x179/0x180 [kvm]
mmu_check_root+0x11/0x30 [kvm]
fast_cr3_switch+0x40/0x120 [kvm]
kvm_mmu_new_cr3+0x34/0x60 [kvm]
nested_vmx_load_cr3+0xbd/0x1f0 [kvm_intel]
nested_vmx_enter_non_root_mode+0xab8/0x1d60 [kvm_intel]
vmx_set_nested_state+0x256/0x340 [kvm_intel]
kvm_arch_vcpu_ioctl+0x491/0x11a0 [kvm]
kvm_vcpu_ioctl+0xde/0x630 [kvm]
do_vfs_ioctl+0xa2/0x6c0
ksys_ioctl+0x66/0x70
__x64_sys_ioctl+0x16/0x20
do_syscall_64+0x54/0x200
entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x7f59a2b95f47
Fixes: 8fcc4b5923af5 ("kvm: nVMX: Introduce KVM_CAP_NESTED_STATE")
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 24885d1d79e2e83d49201aeae0bc59f1402fd4f1 upstream.
A recent change inadvertently exported a static function, which results
in modpost throwing a warning. Fix it.
Fixes: cbbaa2727aa3 ("KVM: x86: fix presentation of TSX feature in ARCH_CAPABILITIES")
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit cbbaa2727aa3ae9e0a844803da7cef7fd3b94f2b upstream.
KVM does not implement MSR_IA32_TSX_CTRL, so it must not be presented
to the guests. It is also confusing to have !ARCH_CAP_TSX_CTRL_MSR &&
!RTM && ARCH_CAP_TAA_NO: lack of MSR_IA32_TSX_CTRL suggests TSX was not
hidden (it actually was), yet the value says that TSX is not vulnerable
to microarchitectural data sampling. Fix both.
Cc: stable@vger.kernel.org
Tested-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit de1fca5d6e0105c9d33924e1247e2f386efc3ece upstream.
"Shared MSRs" are guest MSRs that are written to the host MSRs but
keep their value until the next return to userspace. They support
a mask, so that some bits keep the host value, but this mask is
only used to skip an unnecessary MSR write and the value written
to the MSR is always the guest MSR.
Fix this and, while at it, do not update smsr->values[slot].curr if
for whatever reason the wrmsr fails. This should only happen due to
reserved bits, so the value written to smsr->values[slot].curr
will not match when the user-return notifier and the host value will
always be restored. However, it is untidy and in rare cases this
can actually avoid spurious WRMSRs on return to userspace.
Cc: stable@vger.kernel.org
Reviewed-by: Jim Mattson <jmattson@google.com>
Tested-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit ca185b260951d3b55108c0b95e188682d8a507b7 upstream.
It's possible that two LPIs locate in the same "byte_offset" but target
two different vcpus, where their pending status are indicated by two
different pending tables. In such a scenario, using last_byte_offset
optimization will lead KVM relying on the wrong pending table entry.
Let us use last_ptr instead, which can be treated as a byte index into
a pending table and also, can be vcpu specific.
Fixes: 280771252c1b ("KVM: arm64: vgic-v3: KVM_DEV_ARM_VGIC_SAVE_PENDING_TABLES")
Cc: stable@vger.kernel.org
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Acked-by: Eric Auger <eric.auger@redhat.com>
Link: https://lore.kernel.org/r/20191029071919.177-4-yuzenghui@huawei.com
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 04f11ef45810da5ae2542dd78cc353f3761bd2cb upstream.
Write the desired L2 CR3 into vmcs02.GUEST_CR3 during nested VM-Enter
instead of deferring the VMWRITE until vmx_set_cr3(). If the VMWRITE
is deferred, then KVM can consume a stale vmcs02.GUEST_CR3 when it
refreshes vmcs12->guest_cr3 during nested_vmx_vmexit() if the emulated
VM-Exit occurs without actually entering L2, e.g. if the nested run
is squashed because nested VM-Enter (from L1) is putting L2 into HLT.
Note, the above scenario can occur regardless of whether L1 is
intercepting HLT, e.g. L1 can intercept HLT and then re-enter L2 with
vmcs.GUEST_ACTIVITY_STATE=HALTED. But practically speaking, a VMM will
likely put a guest into HALTED if and only if it's not intercepting HLT.
In an ideal world where EPT *requires* unrestricted guest (and vice
versa), VMX could handle CR3 similar to how it handles RSP and RIP,
e.g. mark CR3 dirty and conditionally load it at vmx_vcpu_run(). But
the unrestricted guest silliness complicates the dirty tracking logic
to the point that explicitly handling vmcs02.GUEST_CR3 during nested
VM-Enter is a simpler overall implementation.
Cc: stable@vger.kernel.org
Reported-and-tested-by: Reto Buerki <reet@codelabs.ch>
Tested-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Reviewed-by: Liran Alon <liran.alon@oracle.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Reviewed-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit e7d71c943040c23f2fd042033d319f56e84f845b upstream.
If we cannot allocate the XIVE VPs in OPAL, the creation of a XIVE or
XICS-on-XIVE device is aborted as expected, but we leave kvm->arch.xive
set forever since the release method isn't called in this case. Any
subsequent tentative to create a XIVE or XICS-on-XIVE for this VM will
thus always fail (DoS). This is a problem for QEMU since it destroys
and re-creates these devices when the VM is reset: the VM would be
restricted to using the much slower emulated XIVE or XICS forever.
As an alternative to adding rollback, do not assign kvm->arch.xive before
making sure the XIVE VPs are allocated in OPAL.
Cc: stable@vger.kernel.org # v5.2
Fixes: 5422e95103cf ("KVM: PPC: Book3S HV: XIVE: Replace the 'destroy' method by a 'release' method")
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 30486e72093ea2e594f44876b7a445c219449bce upstream.
We need to check the host page size is big enough to accomodate the
EQ. Let's do this before taking a reference on the EQ page to avoid
a potential leak if the check fails.
Cc: stable@vger.kernel.org # v5.2
Fixes: 13ce3297c576 ("KVM: PPC: Book3S HV: XIVE: Add controls for the EQ configuration")
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 31a88c82b466d2f31a44e21c479f45b4732ccfd0 upstream.
The EQ page is allocated by the guest and then passed to the hypervisor
with the H_INT_SET_QUEUE_CONFIG hcall. A reference is taken on the page
before handing it over to the HW. This reference is dropped either when
the guest issues the H_INT_RESET hcall or when the KVM device is released.
But, the guest can legitimately call H_INT_SET_QUEUE_CONFIG several times,
either to reset the EQ (vCPU hot unplug) or to set a new EQ (guest reboot).
In both cases the existing EQ page reference is leaked because we simply
overwrite it in the XIVE queue structure without calling put_page().
This is especially visible when the guest memory is backed with huge pages:
start a VM up to the guest userspace, either reboot it or unplug a vCPU,
quit QEMU. The leak is observed by comparing the value of HugePages_Free in
/proc/meminfo before and after the VM is run.
Ideally we'd want the XIVE code to handle the EQ page de-allocation at the
platform level. This isn't the case right now because the various XIVE
drivers have different allocation needs. It could maybe worth introducing
hooks for this purpose instead of exposing XIVE internals to the drivers,
but this is certainly a huge work to be done later.
In the meantime, for easier backport, fix both vCPU unplug and guest reboot
leaks by introducing a wrapper around xive_native_configure_queue() that
does the necessary cleanup.
Reported-by: Satheesh Rajendran <sathnaga@linux.vnet.ibm.com>
Cc: stable@vger.kernel.org # v5.2
Fixes: 13ce3297c576 ("KVM: PPC: Book3S HV: XIVE: Add controls for the EQ configuration")
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Greg Kurz <groug@kaod.org>
Tested-by: Lijun Pan <ljp@linux.ibm.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit bed903167ae5b5532eda5d7db26de451bd232da5 upstream.
Commit ef72171b3621 ("arm64: dts: exynos: Remove unneeded address space
mapping for soc node") changed the address and size cells in root node from
2 to 1, but /memory nodes for the affected boards were not updated. This
went unnoticed on Exynos5433-based TM2(e) boards, because they use u-boot,
which updates /memory node to the correct values. On the other hand, the
mentioned commit broke boot on Exynos7-based Espresso board, which
bootloader doesn't touch /memory node at all.
This patch reverts commit ef72171b3621 ("arm64: dts: exynos: Remove
unneeded address space mapping for soc node"), so Exynos5433 and Exynos7
SoCs again matches other ARM64 platforms with 64bit mappings in root
node.
Reported-by: Alim Akhtar <alim.akhtar@samsung.com>
Fixes: ef72171b3621 ("arm64: dts: exynos: Remove unneeded address space mapping for soc node")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: <stable@vger.kernel.org> # 5.3.x: 72ddcf6aa224 arm64: dts: exynos: Move GPU under /soc node for Exynos5433
Cc: <stable@vger.kernel.org> # 5.3.x: ede87c3a2bdb arm64: dts: exynos: Move GPU under /soc node for Exynos7
Cc: <stable@vger.kernel.org> # 4.18.x
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 4f69851fbaa26b155330be35ce8ac393e93e7442 upstream.
The "used" variables here come from the user in the ioctl and it can be
negative. It could result in an out of bounds write.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20191004102251.GC823@mwanda
Cc: stable@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 354c2d310082d1c384213ba76c3757dd3cd8755d upstream.
Since the dirtyfb ioctl doesn't give us any hints as to which plane is
scanning out the fb it's marking as damaged, we need to loop through
planes to find it.
Currently we just reach into plane state and check, but that can race
with another commit changing the fb out from under us. This patch locks
the plane before checking the fb and will release the lock if the plane
is not displaying the dirty fb.
Fixes: b9fc5e01d1ce ("drm: Add helper to implement legacy dirtyfb")
Cc: Rob Clark <robdclark@gmail.com>
Cc: Deepak Rawat <drawat@vmware.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Thomas Hellstrom <thellstrom@vmware.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Sean Paul <sean@poorly.run>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: dri-devel@lists.freedesktop.org
Cc: <stable@vger.kernel.org> # v5.0+
Reported-by: Daniel Vetter <daniel@ffwll.ch>
Reviewed-by: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190904202938.110207-1-sean@poorly.run
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit a64fc11b9a520c55ca34d82e5ca32274f49b6b15 upstream.
If a process is interrupted while accessing the "gpu" debugfs file and
the drm device struct_mutex is contended, release() could return early
and fail to free related resources.
Note that the return value from release() is ignored.
Fixes: 4f776f4511c7 ("drm/msm/gpu: Convert the GPU show function to use the GPU state")
Cc: stable <stable@vger.kernel.org> # 4.18
Cc: Jordan Crouse <jcrouse@codeaurora.org>
Cc: Rob Clark <robdclark@gmail.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20191010131333.23635-2-johan@kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
Bruce Ashfield
Paul Gortmaker
Charles Keepax
Chen-Yu Tsai
Marek Szyprowski
Andreas Gruenbacher
Robert Richter
Takashi Iwai
Jens Axboe
Navid Emamdoost
Kai Vehmanen
Joel Stanley
Dan Carpenter
Paolo Bonzini
Jann Horn
Wei Wang
Jan Kara
Viresh Kumar
Johan Hovold
Gregory CLEMENT
Patrice Chotard
Frieder Schrempf
Han Xu
Ard Biesheuvel
Mark Salter
Ayush Sawal
Tudor Ambarus
Christian Lamparter
Sean Christopherson
Zenghui Yu
Greg Kurz
Sean Paul