| Age | Commit message (Collapse) | Author |
|---|
|
|
|
This is the 5.15.157 stable release
# -----BEGIN PGP SIGNATURE-----
#
# iQIzBAABCAAdFiEEZH8oZUiU471FcZm+ONu9yGCSaT4FAmYtFFUACgkQONu9yGCS
# aT7CRw//e9KzQRxkyR/qsfuIRtRyEtn2RzaspdVs9HpbtHY+phimUoXMLE/vZYVP
# Fx/g6cfhX42qakrkyj5mAIc7I2V8NbKTNqvzEaxvGNqM2wrTD2sJ//Fu2Dqq9pBx
# a433bfzxi9z+T88UJwszAEzqJt4T8Ph5TeyrRhEHqOb+ZM44Kc/qAG06zQMUSTVH
# Ob6cSFzhxHmGEmU8fPsaPzoqo8k61PahQwtO09pXIaijo2zvOVUVAFvVIez+YXbJ
# 9Ky5J6TTT3IyiSDmBeqga8cyozz8GL0UUGJVVbEGNiAmErCb8GfWlUkBNj/Pm1Ik
# GuiiXljSCGlPVbEXlNODP5H1EgCe6sdbh+rkWyd5bM95A8ol6YqmFyWVu05/pK9I
# P2qHBwLvnXpCOi776OszpNV5di8kNERbJ1mMGdKAOQFcN/X1pzmfBvwRoWkGf3iD
# ni/8m5WybJf9za4pTy48CQY7M0mYsXuN4nKCEm9M23mGYvwC5UVwEfEosjoMVT/0
# Bm6dNP2LOqQisxui7SRW7q1x8wUx1x2P8XOIJV3mXK/VmcVROuTd55GrZGmSyGb5
# U0CK+AQg1X44jCvekQ2jc7sijCSLFwxO2TkwMvASN9F44YWeupDJIAye6vbQQFfF
# qD4q+nShmlaSwTkr3TYMBMbNcjEF1/bNtaSt4bMAhPjM7GfHKUU=
# =Y+VB
# -----END PGP SIGNATURE-----
# gpg: Signature made Sat 27 Apr 2024 11:05:57 AM EDT
# gpg: using RSA key 647F28654894E3BD457199BE38DBBDC86092693E
# gpg: Can't check signature: No public key
|
|
Link: https://lore.kernel.org/r/20240423213844.122920086@linuxfoundation.org
Tested-by: SeongJae Park <sj@kernel.org>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Tested-by: Pavel Machek (CIP) <pavel@denx.de>
Tested-by: Ron Economos <re@w6rz.net>
Tested-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: kernelci.org bot <bot@kernelci.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 06dfcd4098cfdc4d4577d94793a4f9125386da8b upstream.
The commit 40b5d2f15c09 ("net: dsa: mt7530: Add support for EEE features")
brought EEE support but did not enable EEE on MT7531 switch MACs. EEE is
enabled on MT7531 switch MACs by pulling the LAN2LED0 pin low on the board
(bootstrapping), unsetting the EEE_DIS bit on the trap register, or setting
the internal EEE switch bit on the CORE_PLL_GROUP4 register. Thanks to
SkyLake Huang (黃啟澤) from MediaTek for providing information on the
internal EEE switch bit.
There are existing boards that were not designed to pull the pin low.
Because of that, the EEE status currently depends on the board design.
The EEE_DIS bit on the trap pertains to the LAN2LED0 pin which is usually
used to control an LED. Once the bit is unset, the pin will be low. That
will make the active low LED turn on. The pin is controlled by the switch
PHY. It seems that the PHY controls the pin in the way that it inverts the
pin state. That means depending on the wiring of the LED connected to
LAN2LED0 on the board, the LED may be on without an active link.
To not cause this unwanted behaviour whilst enabling EEE on all boards, set
the internal EEE switch bit on the CORE_PLL_GROUP4 register.
My testing on MT7531 shows a certain amount of traffic loss when EEE is
enabled. That said, I haven't come across a board that enables EEE. So
enable EEE on the switch MACs but disable EEE advertisement on the switch
PHYs. This way, we don't change the behaviour of the majority of the boards
that have this switch. The mediatek-ge PHY driver already disables EEE
advertisement on the switch PHYs but my testing shows that it is somehow
enabled afterwards. Disabling EEE advertisement before the PHY driver
initialises keeps it off.
With this change, EEE can now be enabled using ethtool.
Fixes: 40b5d2f15c09 ("net: dsa: mt7530: Add support for EEE features")
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Daniel Golle <daniel@makrotopia.org>
Link: https://lore.kernel.org/r/20240408-for-net-mt7530-fix-eee-for-mt7531-mt7988-v3-1-84fdef1f008b@arinc9.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5f563c31ff0c40ce395d0bae7daa94c7950dac97 upstream.
The MT7530 switch after reset initialises with a core clock frequency that
works with a 25MHz XTAL connected to it. For 40MHz XTAL, the core clock
frequency must be set to 500MHz.
The mt7530_pll_setup() function is responsible of setting the core clock
frequency. Currently, it runs on MT7530 with 25MHz and 40MHz XTAL. This
causes MT7530 switch with 25MHz XTAL to egress and ingress frames
improperly.
Introduce a check to run it only on MT7530 with 40MHz XTAL.
The core clock frequency is set by writing to a switch PHY's register.
Access to the PHY's register is done via the MDIO bus the switch is also
on. Therefore, it works only when the switch makes switch PHYs listen on
the MDIO bus the switch is on. This is controlled either by the state of
the ESW_P1_LED_1 pin after reset deassertion or modifying bit 5 of the
modifiable trap register.
When ESW_P1_LED_1 is pulled high, PHY indirect access is used. That means
accessing PHY registers via the PHY indirect access control register of the
switch.
When ESW_P1_LED_1 is pulled low, PHY direct access is used. That means
accessing PHY registers via the MDIO bus the switch is on.
For MT7530 switch with 40MHz XTAL on a board with ESW_P1_LED_1 pulled high,
the core clock frequency won't be set to 500MHz, causing the switch to
egress and ingress frames improperly.
Run mt7530_pll_setup() after PHY direct access is set on the modifiable
trap register.
With these two changes, all MT7530 switches with 25MHz and 40MHz, and
P1_LED_1 pulled high or low, will egress and ingress frames properly.
Link: https://github.com/BPI-SINOVOIP/BPI-R2-bsp/blob/4a5dd143f2172ec97a2872fa29c7c4cd520f45b5/linux-mt/drivers/net/ethernet/mediatek/gsw_mt7623.c#L1039
Fixes: b8f126a8d543 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Link: https://lore.kernel.org/r/20240320-for-net-mt7530-fix-25mhz-xtal-with-direct-phy-access-v1-1-d92f605f1160@arinc9.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b79d7c14f48083abb3fb061370c0c64a569edf4c upstream.
Since the introduction of the OF bindings, DSA has always had a policy that
in case multiple CPU ports are present in the device tree, the numerically
smallest one is always chosen.
The MT7530 switch family, except the switch on the MT7988 SoC, has 2 CPU
ports, 5 and 6, where port 6 is preferable on the MT7531BE switch because
it has higher bandwidth.
The MT7530 driver developers had 3 options:
- to modify DSA when the MT7531 switch support was introduced, such as to
prefer the better port
- to declare both CPU ports in device trees as CPU ports, and live with the
sub-optimal performance resulting from not preferring the better port
- to declare just port 6 in the device tree as a CPU port
Of course they chose the path of least resistance (3rd option), kicking the
can down the road. The hardware description in the device tree is supposed
to be stable - developers are not supposed to adopt the strategy of
piecemeal hardware description, where the device tree is updated in
lockstep with the features that the kernel currently supports.
Now, as a result of the fact that they did that, any attempts to modify the
device tree and describe both CPU ports as CPU ports would make DSA change
its default selection from port 6 to 5, effectively resulting in a
performance degradation visible to users with the MT7531BE switch as can be
seen below.
Without preferring port 6:
[ ID][Role] Interval Transfer Bitrate Retr
[ 5][TX-C] 0.00-20.00 sec 374 MBytes 157 Mbits/sec 734 sender
[ 5][TX-C] 0.00-20.00 sec 373 MBytes 156 Mbits/sec receiver
[ 7][RX-C] 0.00-20.00 sec 1.81 GBytes 778 Mbits/sec 0 sender
[ 7][RX-C] 0.00-20.00 sec 1.81 GBytes 777 Mbits/sec receiver
With preferring port 6:
[ ID][Role] Interval Transfer Bitrate Retr
[ 5][TX-C] 0.00-20.00 sec 1.99 GBytes 856 Mbits/sec 273 sender
[ 5][TX-C] 0.00-20.00 sec 1.99 GBytes 855 Mbits/sec receiver
[ 7][RX-C] 0.00-20.00 sec 1.72 GBytes 737 Mbits/sec 15 sender
[ 7][RX-C] 0.00-20.00 sec 1.71 GBytes 736 Mbits/sec receiver
Using one port for WAN and the other ports for LAN is a very popular use
case which is what this test emulates.
As such, this change proposes that we retroactively modify stable kernels
(which don't support the modification of the CPU port assignments, so as to
let user space fix the problem and restore the throughput) to keep the
mt7530 driver preferring port 6 even with device trees where the hardware
is more fully described.
Fixes: c288575f7810 ("net: dsa: mt7530: Add the support of MT7531 switch")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ff221029a51fd54cacac66e193e0c75e4de940e7 upstream.
MT7531_CPU_PMAP represents the destination port mask for trapped-to-CPU
frames (further restricted by PCR_MATRIX).
Currently the driver sets the first CPU port as the single port in this bit
mask, which works fine regardless of whether the device tree defines port
5, 6 or 5+6 as CPU ports. This is because the logic coincides with DSA's
logic of picking the first CPU port as the CPU port that all user ports are
affine to, by default.
An upcoming change would like to influence DSA's selection of the default
CPU port to no longer be the first one, and in that case, this logic needs
adaptation.
Since there is no observed leakage or duplication of frames if all CPU
ports are defined in this bit mask, simply include them all.
Suggested-by: Russell King (Oracle) <linux@armlinux.org.uk>
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c4a7dc9523b59b3e73fd522c73e95e072f876b16 upstream.
The size of the nilfs_type_by_mode array in the fs/nilfs2/dir.c file is
defined as "S_IFMT >> S_SHIFT", but the nilfs_set_de_type() function,
which uses this array, specifies the index to read from the array in the
same way as "(mode & S_IFMT) >> S_SHIFT".
static void nilfs_set_de_type(struct nilfs_dir_entry *de, struct inode
*inode)
{
umode_t mode = inode->i_mode;
de->file_type = nilfs_type_by_mode[(mode & S_IFMT)>>S_SHIFT]; // oob
}
However, when the index is determined this way, an out-of-bounds (OOB)
error occurs by referring to an index that is 1 larger than the array size
when the condition "mode & S_IFMT == S_IFMT" is satisfied. Therefore, a
patch to resize the nilfs_type_by_mode array should be applied to prevent
OOB errors.
Link: https://lkml.kernel.org/r/20240415182048.7144-1-konishi.ryusuke@gmail.com
Reported-by: syzbot+2e22057de05b9f3b30d8@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=2e22057de05b9f3b30d8
Fixes: 2ba466d74ed7 ("nilfs2: directory entry operations")
Signed-off-by: Jeongjun Park <aha310510@gmail.com>
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@gmail.com>
Tested-by: Ryusuke Konishi <konishi.ryusuke@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit fff1386cc889d8fb4089d285f883f8cba62d82ce upstream.
Running a lot of VK CTS in parallel against nouveau, once every
few hours you might see something like this crash.
BUG: kernel NULL pointer dereference, address: 0000000000000008
PGD 8000000114e6e067 P4D 8000000114e6e067 PUD 109046067 PMD 0
Oops: 0000 [#1] PREEMPT SMP PTI
CPU: 7 PID: 53891 Comm: deqp-vk Not tainted 6.8.0-rc6+ #27
Hardware name: Gigabyte Technology Co., Ltd. Z390 I AORUS PRO WIFI/Z390 I AORUS PRO WIFI-CF, BIOS F8 11/05/2021
RIP: 0010:gp100_vmm_pgt_mem+0xe3/0x180 [nouveau]
Code: c7 48 01 c8 49 89 45 58 85 d2 0f 84 95 00 00 00 41 0f b7 46 12 49 8b 7e 08 89 da 42 8d 2c f8 48 8b 47 08 41 83 c7 01 48 89 ee <48> 8b 40 08 ff d0 0f 1f 00 49 8b 7e 08 48 89 d9 48 8d 75 04 48 c1
RSP: 0000:ffffac20c5857838 EFLAGS: 00010202
RAX: 0000000000000000 RBX: 00000000004d8001 RCX: 0000000000000001
RDX: 00000000004d8001 RSI: 00000000000006d8 RDI: ffffa07afe332180
RBP: 00000000000006d8 R08: ffffac20c5857ad0 R09: 0000000000ffff10
R10: 0000000000000001 R11: ffffa07af27e2de0 R12: 000000000000001c
R13: ffffac20c5857ad0 R14: ffffa07a96fe9040 R15: 000000000000001c
FS: 00007fe395eed7c0(0000) GS:ffffa07e2c980000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000008 CR3: 000000011febe001 CR4: 00000000003706f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
...
? gp100_vmm_pgt_mem+0xe3/0x180 [nouveau]
? gp100_vmm_pgt_mem+0x37/0x180 [nouveau]
nvkm_vmm_iter+0x351/0xa20 [nouveau]
? __pfx_nvkm_vmm_ref_ptes+0x10/0x10 [nouveau]
? __pfx_gp100_vmm_pgt_mem+0x10/0x10 [nouveau]
? __pfx_gp100_vmm_pgt_mem+0x10/0x10 [nouveau]
? __lock_acquire+0x3ed/0x2170
? __pfx_gp100_vmm_pgt_mem+0x10/0x10 [nouveau]
nvkm_vmm_ptes_get_map+0xc2/0x100 [nouveau]
? __pfx_nvkm_vmm_ref_ptes+0x10/0x10 [nouveau]
? __pfx_gp100_vmm_pgt_mem+0x10/0x10 [nouveau]
nvkm_vmm_map_locked+0x224/0x3a0 [nouveau]
Adding any sort of useful debug usually makes it go away, so I hand
wrote the function in a line, and debugged the asm.
Every so often pt->memory->ptrs is NULL. This ptrs ptr is set in
the nv50_instobj_acquire called from nvkm_kmap.
If Thread A and Thread B both get to nv50_instobj_acquire around
the same time, and Thread A hits the refcount_set line, and in
lockstep thread B succeeds at refcount_inc_not_zero, there is a
chance the ptrs value won't have been stored since refcount_set
is unordered. Force a memory barrier here, I picked smp_mb, since
we want it on all CPUs and it's write followed by a read.
v2: use paired smp_rmb/smp_wmb.
Cc: <stable@vger.kernel.org>
Fixes: be55287aa5ba ("drm/nouveau/imem/nv50: embed nvkm_instobj directly into nv04_instobj")
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Danilo Krummrich <dakr@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240411011510.2546857-1-airlied@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d4c972bff3129a9dd4c22a3999fd8eba1a81531a upstream.
The table of primary plane formats wasn't sorted at all, leading to
applications picking our least desirable formats by defaults.
Sort the primary plane formats according to our order of preference.
Nice side-effect of this change is that it makes IGT's kms_atomic
plane-invalid-params pass because the test picks the first format
which for vmwgfx was DRM_FORMAT_XRGB1555 and uses fb's with odd sizes
which make Pixman, which IGT depends on assert due to the fact that our
16bpp formats aren't 32 bit aligned like Pixman requires all formats
to be.
Signed-off-by: Zack Rusin <zack.rusin@broadcom.com>
Fixes: 36cc79bc9077 ("drm/vmwgfx: Add universal plane support")
Cc: Broadcom internal kernel review list <bcm-kernel-feedback-list@broadcom.com>
Cc: dri-devel@lists.freedesktop.org
Cc: <stable@vger.kernel.org> # v4.12+
Acked-by: Pekka Paalanen <pekka.paalanen@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240412025511.78553-6-zack.rusin@broadcom.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6fef2d4c00b5b8561ad68dd2b68173f5c6af1e75 upstream.
Verify the parameters of
amdgpu_vm_bo_(map/replace_map/clearing_mappings) in one common place.
Fixes: dc54d3d1744d ("drm/amdgpu: implement AMDGPU_VA_OP_CLEAR v2")
Cc: stable@vger.kernel.org
Reported-by: Vlad Stolyarov <hexed@google.com>
Suggested-by: Christian König <christian.koenig@amd.com>
Signed-off-by: xinhui pan <xinhui.pan@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit aaef73821a3b0194a01bd23ca77774f704a04d40 upstream.
Commit 6d98eb95b450 ("binder: avoid potential data leakage when copying
txn") introduced changes to how binder objects are copied. In doing so,
it unintentionally removed an offset alignment check done through calls
to binder_alloc_copy_from_buffer() -> check_buffer().
These calls were replaced in binder_get_object() with copy_from_user(),
so now an explicit offset alignment check is needed here. This avoids
later complications when unwinding the objects gets harder.
It is worth noting this check existed prior to commit 7a67a39320df
("binder: add function to copy binder object from buffer"), likely
removed due to redundancy at the time.
Fixes: 6d98eb95b450 ("binder: avoid potential data leakage when copying txn")
Cc: stable@vger.kernel.org
Signed-off-by: Carlos Llamas <cmllamas@google.com>
Acked-by: Todd Kjos <tkjos@google.com>
Link: https://lore.kernel.org/r/20240330190115.1877819-1-cmllamas@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 46dad3c1e57897ab9228332f03e1c14798d2d3b9 upstream.
We allocate memory of size 'xlen + strlen(boot_command_line) + 1' for
static_command_line, but the strings copied into static_command_line are
extra_command_line and command_line, rather than extra_command_line and
boot_command_line.
When strlen(command_line) > strlen(boot_command_line), static_command_line
will overflow.
This patch just recovers strlen(command_line) which was miss-consolidated
with strlen(boot_command_line) in the commit f5c7310ac73e ("init/main: add
checks for the return value of memblock_alloc*()")
Link: https://lore.kernel.org/all/20240412081733.35925-2-ytcoode@gmail.com/
Fixes: f5c7310ac73e ("init/main: add checks for the return value of memblock_alloc*()")
Cc: stable@vger.kernel.org
Signed-off-by: Yuntao Wang <ytcoode@gmail.com>
Signed-off-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 50449ca66cc5a8cbc64749cf4b9f3d3fc5f4b457 upstream.
On arm64 machines, swsusp_save() faults if it attempts to access
MEMBLOCK_NOMAP memory ranges. This can be reproduced in QEMU using UEFI
when booting with rodata=off debug_pagealloc=off and CONFIG_KFENCE=n:
Unable to handle kernel paging request at virtual address ffffff8000000000
Mem abort info:
ESR = 0x0000000096000007
EC = 0x25: DABT (current EL), IL = 32 bits
SET = 0, FnV = 0
EA = 0, S1PTW = 0
FSC = 0x07: level 3 translation fault
Data abort info:
ISV = 0, ISS = 0x00000007, ISS2 = 0x00000000
CM = 0, WnR = 0, TnD = 0, TagAccess = 0
GCS = 0, Overlay = 0, DirtyBit = 0, Xs = 0
swapper pgtable: 4k pages, 39-bit VAs, pgdp=00000000eeb0b000
[ffffff8000000000] pgd=180000217fff9803, p4d=180000217fff9803, pud=180000217fff9803, pmd=180000217fff8803, pte=0000000000000000
Internal error: Oops: 0000000096000007 [#1] SMP
Internal error: Oops: 0000000096000007 [#1] SMP
Modules linked in: xt_multiport ipt_REJECT nf_reject_ipv4 xt_conntrack nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 libcrc32c iptable_filter bpfilter rfkill at803x snd_hda_codec_hdmi snd_hda_intel snd_intel_dspcfg dwmac_generic stmmac_platform snd_hda_codec stmmac joydev pcs_xpcs snd_hda_core phylink ppdev lp parport ramoops reed_solomon ip_tables x_tables nls_iso8859_1 vfat multipath linear amdgpu amdxcp drm_exec gpu_sched drm_buddy hid_generic usbhid hid radeon video drm_suballoc_helper drm_ttm_helper ttm i2c_algo_bit drm_display_helper cec drm_kms_helper drm
CPU: 0 PID: 3663 Comm: systemd-sleep Not tainted 6.6.2+ #76
Source Version: 4e22ed63a0a48e7a7cff9b98b7806d8d4add7dc0
Hardware name: Greatwall GW-XXXXXX-XXX/GW-XXXXXX-XXX, BIOS KunLun BIOS V4.0 01/19/2021
pstate: 600003c5 (nZCv DAIF -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : swsusp_save+0x280/0x538
lr : swsusp_save+0x280/0x538
sp : ffffffa034a3fa40
x29: ffffffa034a3fa40 x28: ffffff8000001000 x27: 0000000000000000
x26: ffffff8001400000 x25: ffffffc08113e248 x24: 0000000000000000
x23: 0000000000080000 x22: ffffffc08113e280 x21: 00000000000c69f2
x20: ffffff8000000000 x19: ffffffc081ae2500 x18: 0000000000000000
x17: 6666662074736420 x16: 3030303030303030 x15: 3038666666666666
x14: 0000000000000b69 x13: ffffff9f89088530 x12: 00000000ffffffea
x11: 00000000ffff7fff x10: 00000000ffff7fff x9 : ffffffc08193f0d0
x8 : 00000000000bffe8 x7 : c0000000ffff7fff x6 : 0000000000000001
x5 : ffffffa0fff09dc8 x4 : 0000000000000000 x3 : 0000000000000027
x2 : 0000000000000000 x1 : 0000000000000000 x0 : 000000000000004e
Call trace:
swsusp_save+0x280/0x538
swsusp_arch_suspend+0x148/0x190
hibernation_snapshot+0x240/0x39c
hibernate+0xc4/0x378
state_store+0xf0/0x10c
kobj_attr_store+0x14/0x24
The reason is swsusp_save() -> copy_data_pages() -> page_is_saveable()
-> kernel_page_present() assuming that a page is always present when
can_set_direct_map() is false (all of rodata_full,
debug_pagealloc_enabled() and arm64_kfence_can_set_direct_map() false),
irrespective of the MEMBLOCK_NOMAP ranges. Such MEMBLOCK_NOMAP regions
should not be saved during hibernation.
This problem was introduced by changes to the pfn_valid() logic in
commit a7d9f306ba70 ("arm64: drop pfn_valid_within() and simplify
pfn_valid()").
Similar to other architectures, drop the !can_set_direct_map() check in
kernel_page_present() so that page_is_savable() skips such pages.
Fixes: a7d9f306ba70 ("arm64: drop pfn_valid_within() and simplify pfn_valid()")
Cc: <stable@vger.kernel.org> # 5.14.x
Suggested-by: Mike Rapoport <rppt@kernel.org>
Suggested-by: Catalin Marinas <catalin.marinas@arm.com>
Co-developed-by: xiongxin <xiongxin@kylinos.cn>
Signed-off-by: xiongxin <xiongxin@kylinos.cn>
Signed-off-by: Yaxiong Tian <tianyaxiong@kylinos.cn>
Acked-by: Mike Rapoport (IBM) <rppt@kernel.org>
Link: https://lore.kernel.org/r/20240417025248.386622-1-tianyaxiong@kylinos.cn
[catalin.marinas@arm.com: rework commit message]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 49ff3b4aec51e3abfc9369997cc603319b02af9a upstream.
On AMD and Hygon platforms, the local APIC does not automatically set
the mask bit of the LVTPC register when handling a PMI and there is
no need to clear it in the kernel's PMI handler.
For guests, the mask bit is currently set by kvm_apic_local_deliver()
and unless it is cleared by the guest kernel's PMI handler, PMIs stop
arriving and break use-cases like sampling with perf record.
This does not affect non-PerfMonV2 guests because PMIs are handled in
the guest kernel by x86_pmu_handle_irq() which always clears the LVTPC
mask bit irrespective of the vendor.
Before:
$ perf record -e cycles:u true
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.001 MB perf.data (1 samples) ]
After:
$ perf record -e cycles:u true
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.002 MB perf.data (19 samples) ]
Fixes: a16eb25b09c0 ("KVM: x86: Mask LVTPC when handling a PMI")
Cc: stable@vger.kernel.org
Signed-off-by: Sandipan Das <sandipan.das@amd.com>
Reviewed-by: Jim Mattson <jmattson@google.com>
[sean: use is_intel_compatible instead of !is_amd_or_hygon()]
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-ID: <20240405235603.1173076-3-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit fd706c9b1674e2858766bfbf7430534c2b26fbef upstream.
Add kvm_vcpu_arch.is_amd_compatible to cache if a vCPU's vendor model is
compatible with AMD, i.e. if the vCPU vendor is AMD or Hygon, along with
helpers to check if a vCPU is compatible AMD vs. Intel. To handle Intel
vs. AMD behavior related to masking the LVTPC entry, KVM will need to
check for vendor compatibility on every PMI injection, i.e. querying for
AMD will soon be a moderately hot path.
Note! This subtly (or maybe not-so-subtly) makes "Intel compatible" KVM's
default behavior, both if userspace omits (or never sets) CPUID 0x0 and if
userspace sets a completely unknown vendor. One could argue that KVM
should treat such vCPUs as not being compatible with Intel *or* AMD, but
that would add useless complexity to KVM.
KVM needs to do *something* in the face of vendor specific behavior, and
so unless KVM conjured up a magic third option, choosing to treat unknown
vendors as neither Intel nor AMD means that checks on AMD compatibility
would yield Intel behavior, and checks for Intel compatibility would yield
AMD behavior. And that's far worse as it would effectively yield random
behavior depending on whether KVM checked for AMD vs. Intel vs. !AMD vs.
!Intel. And practically speaking, all x86 CPUs follow either Intel or AMD
architecture, i.e. "supporting" an unknown third architecture adds no
value.
Deliberately don't convert any of the existing guest_cpuid_is_intel()
checks, as the Intel side of things is messier due to some flows explicitly
checking for exactly vendor==Intel, versus some flows assuming anything
that isn't "AMD compatible" gets Intel behavior. The Intel code will be
cleaned up in the future.
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-ID: <20240405235603.1173076-2-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a90bca2228c0646fc29a72689d308e5fe03e6d78 upstream.
The sysfs_break_active_protection() routine has an obvious reference
leak in its error path. If the call to kernfs_find_and_get() fails then
kn will be NULL, so the companion sysfs_unbreak_active_protection()
routine won't get called (and would only cause an access violation by
trying to dereference kn->parent if it was called). As a result, the
reference to kobj acquired at the start of the function will never be
released.
Fix the leak by adding an explicit kobject_put() call when kn is NULL.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Fixes: 2afc9166f79b ("scsi: sysfs: Introduce sysfs_{un,}break_active_protection()")
Cc: Bart Van Assche <bvanassche@acm.org>
Cc: stable@vger.kernel.org
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Tejun Heo <tj@kernel.org>
Link: https://lore.kernel.org/r/8a4d3f0f-c5e3-4b70-a188-0ca433f9e6f9@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c8d2f34ea96ea3bce6ba2535f867f0d4ee3b22e1 upstream.
In case a console is set up really large and contains a really long word
(> 256 characters), we have to stop before the length of the word buffer.
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Fixes: c6e3fd22cd538 ("Staging: add speakup to the staging directory")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240323164843.1426997-1-samuel.thibault@ens-lyon.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0dc04112bee6fdd6eb847ccb32214703022c0269 upstream.
Extend the quirk to disable MEI interface on Intel PCH Ignition (IGN)
and SPS firmwares for RPL-S devices. These firmwares do not support
the MEI protocol.
Fixes: 3ed8c7d39cfe ("mei: me: add raptor lake point S DID")
Cc: stable@vger.kernel.org
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Link: https://lore.kernel.org/r/20240312051958.118478-1-tomas.winkler@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6334b8e4553cc69f51e383c9de545082213d785e upstream.
When ncm function is working and then stop usb0 interface for link down,
eth_stop() is called. At this piont, accidentally if usb transport error
should happen in usb_ep_enable(), 'in_ep' and/or 'out_ep' may not be enabled.
After that, ncm_disable() is called to disable for ncm unbind
but gether_disconnect() is never called since 'in_ep' is not enabled.
As the result, ncm object is released in ncm unbind
but 'dev->port_usb' associated to 'ncm->port' is not NULL.
And when ncm bind again to recover netdev, ncm object is reallocated
but usb0 interface is already associated to previous released ncm object.
Therefore, once usb0 interface is up and eth_start_xmit() is called,
released ncm object is dereferrenced and it might cause use-after-free memory.
[function unlink via configfs]
usb0: eth_stop dev->port_usb=ffffff9b179c3200
--> error happens in usb_ep_enable().
NCM: ncm_disable: ncm=ffffff9b179c3200
--> no gether_disconnect() since ncm->port.in_ep->enabled is false.
NCM: ncm_unbind: ncm unbind ncm=ffffff9b179c3200
NCM: ncm_free: ncm free ncm=ffffff9b179c3200 <-- released ncm
[function link via configfs]
NCM: ncm_alloc: ncm alloc ncm=ffffff9ac4f8a000
NCM: ncm_bind: ncm bind ncm=ffffff9ac4f8a000
NCM: ncm_set_alt: ncm=ffffff9ac4f8a000 alt=0
usb0: eth_open dev->port_usb=ffffff9b179c3200 <-- previous released ncm
usb0: eth_start dev->port_usb=ffffff9b179c3200 <--
eth_start_xmit()
--> dev->wrap()
Unable to handle kernel paging request at virtual address dead00000000014f
This patch addresses the issue by checking if 'ncm->netdev' is not NULL at
ncm_disable() to call gether_disconnect() to deassociate 'dev->port_usb'.
It's more reasonable to check 'ncm->netdev' to call gether_connect/disconnect
rather than check 'ncm->port.in_ep->enabled' since it might not be enabled
but the gether connection might be established.
Signed-off-by: Norihiko Hama <Norihiko.Hama@alpsalpine.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20240327023550.51214-1-Norihiko.Hama@alpsalpine.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d920a2ed8620be04a3301e1a9c2b7cc1de65f19d upstream.
SanDisks USB3 storage may disapper after system reboot:
usb usb2-port3: link state change
xhci_hcd 0000:00:14.0: clear port3 link state change, portsc: 0x2c0
usb usb2-port3: do warm reset, port only
xhci_hcd 0000:00:14.0: xhci_hub_status_data: stopping usb2 port polling
xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x2b0, return 0x2b0
usb usb2-port3: not warm reset yet, waiting 50ms
xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x2f0, return 0x2f0
usb usb2-port3: not warm reset yet, waiting 200ms
...
xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x6802c0, return 0x7002c0
usb usb2-port3: not warm reset yet, waiting 200ms
xhci_hcd 0000:00:14.0: clear port3 reset change, portsc: 0x4802c0
xhci_hcd 0000:00:14.0: clear port3 warm(BH) reset change, portsc: 0x4002c0
xhci_hcd 0000:00:14.0: clear port3 link state change, portsc: 0x2c0
xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x2c0, return 0x2c0
usb usb2-port3: not enabled, trying warm reset again...
This is due to the USB device still cause port change event after xHCI is
shuted down:
xhci_hcd 0000:38:00.0: // Setting command ring address to 0xffffe001
xhci_hcd 0000:38:00.0: xhci_resume: starting usb3 port polling.
xhci_hcd 0000:38:00.0: xhci_hub_status_data: stopping usb4 port polling
xhci_hcd 0000:38:00.0: xhci_hub_status_data: stopping usb3 port polling
xhci_hcd 0000:38:00.0: hcd_pci_runtime_resume: 0
xhci_hcd 0000:38:00.0: xhci_shutdown: stopping usb3 port polling.
xhci_hcd 0000:38:00.0: // Halt the HC
xhci_hcd 0000:38:00.0: xhci_shutdown completed - status = 1
xhci_hcd 0000:00:14.0: xhci_shutdown: stopping usb1 port polling.
xhci_hcd 0000:00:14.0: // Halt the HC
xhci_hcd 0000:00:14.0: xhci_shutdown completed - status = 1
xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x1203, return 0x203
xhci_hcd 0000:00:14.0: set port reset, actual port 2-3 status = 0x1311
xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x201203, return 0x100203
xhci_hcd 0000:00:14.0: clear port3 reset change, portsc: 0x1203
xhci_hcd 0000:00:14.0: clear port3 warm(BH) reset change, portsc: 0x1203
xhci_hcd 0000:00:14.0: clear port3 link state change, portsc: 0x1203
xhci_hcd 0000:00:14.0: clear port3 connect change, portsc: 0x1203
xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x1203, return 0x203
usb 2-3: device not accepting address 2, error -108
xhci_hcd 0000:00:14.0: xHCI dying or halted, can't queue_command
xhci_hcd 0000:00:14.0: Set port 2-3 link state, portsc: 0x1203, write 0x11261
xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x1263, return 0x263
xhci_hcd 0000:00:14.0: set port reset, actual port 2-3 status = 0x1271
xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x12b1, return 0x2b1
usb usb2-port3: not reset yet, waiting 60ms
ACPI: PM: Preparing to enter system sleep state S5
xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x12f1, return 0x2f1
usb usb2-port3: not reset yet, waiting 200ms
reboot: Restarting system
The port change event is caused by LPM transition, so disabling LPM at shutdown
to make sure the device is in U0 for warmboot.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20240305065140.66801-1-kai.heng.feng@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit eed04fa96c48790c1cce73c8a248e9d460b088f8 upstream.
Fixed variable dereference issue in DDMA completion flow.
Fixes: b258e4268850 ("usb: dwc2: host: Fix ISOC flow in DDMA mode")
CC: stable@vger.kernel.org
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/linux-usb/2024040834-ethically-rumble-701f@gregkh/T/#m4c4b83bef0ebb4b67fe2e0a7d6466cbb6f416e39
Signed-off-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Link: https://lore.kernel.org/r/cc826d3ef53c934d8e6d98870f17f3cdc3d2755d.1712665387.git.Minas.Harutyunyan@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1607830dadeefc407e4956336d9fcd9e9defd810 upstream.
This reverts commit 339f83612f3a569b194680768b22bf113c26a29d.
It has been found to cause problems in a number of Chromebook devices,
so revert the change until it can be brought back in a safe way.
Link: https://lore.kernel.org/r/385a3519-b45d-48c5-a6fd-a3fdb6bec92f@chromium.org
Reported-by:: Aleksander Morgado <aleksandermj@chromium.org>
Fixes: 339f83612f3a ("usb: cdc-wdm: close race between read and workqueue")
Cc: stable <stable@kernel.org>
Cc: Oliver Neukum <oneukum@suse.com>
Cc: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 582ee2f9d268d302595db3e36b985e5cbb93284d upstream.
Add the following Telit FN920C04 compositions:
0x10a0: rmnet + tty (AT/NMEA) + tty (AT) + tty (diag)
T: Bus=03 Lev=01 Prnt=03 Port=06 Cnt=01 Dev#= 5 Spd=480 MxCh= 0
D: Ver= 2.01 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1bc7 ProdID=10a0 Rev=05.15
S: Manufacturer=Telit Cinterion
S: Product=FN920
S: SerialNumber=92c4c4d8
C: #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=50 Driver=qmi_wwan
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=82(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=60 Driver=option
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=84(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=86(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
0x10a4: rmnet + tty (AT) + tty (AT) + tty (diag)
T: Bus=03 Lev=01 Prnt=03 Port=06 Cnt=01 Dev#= 8 Spd=480 MxCh= 0
D: Ver= 2.01 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1bc7 ProdID=10a4 Rev=05.15
S: Manufacturer=Telit Cinterion
S: Product=FN920
S: SerialNumber=92c4c4d8
C: #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=50 Driver=qmi_wwan
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=82(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=84(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=86(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
0x10a9: rmnet + tty (AT) + tty (diag) + DPL (data packet logging) + adb
T: Bus=03 Lev=01 Prnt=03 Port=06 Cnt=01 Dev#= 9 Spd=480 MxCh= 0
D: Ver= 2.01 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1bc7 ProdID=10a9 Rev=05.15
S: Manufacturer=Telit Cinterion
S: Product=FN920
S: SerialNumber=92c4c4d8
C: #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=50 Driver=qmi_wwan
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=82(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=84(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 3 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=80 Driver=(none)
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none)
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 311f97a4c7c22a01f8897bddf00428dfd0668e79 upstream.
Update the USB serial option driver support for the Rolling
LTE modules.
- VID:PID 33f8:01a2, RW101-GL for laptop debug M.2 cards(with MBIM
interface for /Linux/Chrome OS)
0x01a2: mbim, diag, at, pipe
- VID:PID 33f8:01a3, RW101-GL for laptop debug M.2 cards(with MBIM
interface for /Linux/Chrome OS)
0x01a3: mbim, pipe
- VID:PID 33f8:01a4, RW101-GL for laptop debug M.2 cards(with MBIM
interface for /Linux/Chrome OS)
0x01a4: mbim, diag, at, pipe
- VID:PID 33f8:0104, RW101-GL for laptop debug M.2 cards(with RMNET
interface for /Linux/Chrome OS)
0x0104: RMNET, diag, at, pipe
- VID:PID 33f8:0115, RW135-GL for laptop debug M.2 cards(with MBIM
interface for /Linux/Chrome OS)
0x0115: MBIM, diag, at, pipe
Here are the outputs of usb-devices:
T: Bus=01 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 5 Spd=480 MxCh= 0
D: Ver= 2.01 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=33f8 ProdID=01a2 Rev=05.15
S: Manufacturer=Rolling Wireless S.a.r.l.
S: Product=Rolling Module
S: SerialNumber=12345678
C: #Ifs= 5 Cfg#= 1 Atr=a0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim
E: Ad=82(I) Atr=03(Int.) MxPS= 64 Ivl=32ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=84(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
T: Bus=01 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 8 Spd=480 MxCh= 0
D: Ver= 2.01 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=33f8 ProdID=01a3 Rev=05.15
S: Manufacturer=Rolling Wireless S.a.r.l.
S: Product=Rolling Module
S: SerialNumber=12345678
C: #Ifs= 3 Cfg#= 1 Atr=a0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim
E: Ad=82(I) Atr=03(Int.) MxPS= 64 Ivl=32ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
T: Bus=01 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 17 Spd=480 MxCh= 0
D: Ver= 2.01 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=33f8 ProdID=01a4 Rev=05.15
S: Manufacturer=Rolling Wireless S.a.r.l.
S: Product=Rolling Module
S: SerialNumber=12345678
C: #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim
E: Ad=82(I) Atr=03(Int.) MxPS= 64 Ivl=32ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=usbfs
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
T: Bus=04 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=5000 MxCh= 0
D: Ver= 3.20 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 9 #Cfgs= 1
P: Vendor=33f8 ProdID=0104 Rev=05.04
S: Manufacturer=Rolling Wireless S.a.r.l.
S: Product=Rolling Module
S: SerialNumber=ba2eb033
C: #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=896mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E: Ad=01(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=02(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=03(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=84(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=40 Driver=option
E: Ad=04(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=86(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=87(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=50 Driver=qmi_wwan
E: Ad=0f(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=88(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
E: Ad=8e(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I: If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=usbfs
E: Ad=05(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=89(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
T: Bus=01 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 16 Spd=480 MxCh= 0
D: Ver= 2.01 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=33f8 ProdID=0115 Rev=05.15
S: Manufacturer=Rolling Wireless S.a.r.l.
S: Product=Rolling Module
S: SerialNumber=12345678
C: #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim
E: Ad=82(I) Atr=03(Int.) MxPS= 64 Ivl=32ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=usbfs
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Signed-off-by: Vanillan Wang <vanillanwang@163.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c840244aba7ad2b83ed904378b36bd6aef25511c upstream.
EM060K_129, EM060K_12a, EM060K_12b and EM0060K_12c are EM060K's sub-models,
having the same name "Quectel EM060K-GL" and the same interface layout.
MBIM + GNSS + DIAG + NMEA + AT + QDSS + DPL
T: Bus=03 Lev=01 Prnt=01 Port=01 Cnt=02 Dev#= 8 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=2c7c ProdID=0129 Rev= 5.04
S: Manufacturer=Quectel
S: Product=Quectel EM060K-GL
S: SerialNumber=f6fa08b6
C:* #Ifs= 8 Cfg#= 1 Atr=a0 MxPwr=500mA
A: FirstIf#= 0 IfCount= 2 Cls=02(comm.) Sub=0e Prot=00
I:* If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=0e Prot=00 Driver=cdc_mbim
E: Ad=81(I) Atr=03(Int.) MxPS= 64 Ivl=32ms
I: If#= 1 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
I:* If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
E: Ad=8e(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=0f(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=82(I) Atr=03(Int.) MxPS= 64 Ivl=32ms
I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=40 Driver=option
E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=87(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 6 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=70 Driver=(none)
E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 7 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=80 Driver=(none)
E: Ad=8f(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Signed-off-by: Jerry Meng <jerry-meng@foxmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit cf16ffa17c398434a77b8a373e69287c95b60de2 upstream.
Update the USB serial option driver to support Longsung U8300/U9300.
For U8300
Interface 4 is used by for QMI interface in stock firmware of U8300, the
router which uses U8300 modem.
Interface 5 is used by for ADB interface in stock firmware of U8300, the
router which uses U8300 modem.
Interface mapping is:
0: unknown (Debug), 1: AT (Modem), 2: AT, 3: PPP (NDIS / Pipe), 4: QMI, 5: ADB
T: Bus=05 Lev=01 Prnt=03 Port=02 Cnt=01 Dev#= 4 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1c9e ProdID=9b05 Rev=03.18
S: Manufacturer=Android
S: Product=Android
C: #Ifs= 6 Cfg#= 1 Atr=80 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=87(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=89(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
I: If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none)
E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=8a(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
For U9300
Interface 1 is used by for ADB interface in stock firmware of U9300, the
router which uses U9300 modem.
Interface 4 is used by for QMI interface in stock firmware of U9300, the
router which uses U9300 modem.
Interface mapping is:
0: ADB, 1: AT (Modem), 2: AT, 3: PPP (NDIS / Pipe), 4: QMI
Note: Interface 3 of some models of the U9300 series can send AT commands.
T: Bus=05 Lev=01 Prnt=05 Port=04 Cnt=01 Dev#= 6 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1c9e ProdID=9b3c Rev=03.18
S: Manufacturer=Android
S: Product=Android
C: #Ifs= 5 Cfg#= 1 Atr=80 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none)
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=87(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=89(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
Tested successfully using Modem Manager on U9300.
Tested successfully AT commands using If=1, If=2 and If=3 on U9300.
Signed-off-by: Coia Prant <coiaprant@gmail.com>
Reviewed-by: Lars Melin <larsm17@gmail.com>
[ johan: drop product defines, trim commit message ]
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit fb1f4584b1215e8c209f6b3a4028ed8351a0e961 upstream.
Fibocom FM650/FG650 are 5G modems with ECM/NCM/RNDIS/MBIM modes.
This patch adds support to all 4 modes.
In all 4 modes, the first serial port is the AT console while the other
3 appear to be diagnostic interfaces for dumping modem logs.
usb-devices output for all modes:
ECM:
T: Bus=04 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 5 Spd=5000 MxCh= 0
D: Ver= 3.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 9 #Cfgs= 1
P: Vendor=2cb7 ProdID=0a04 Rev=04.04
S: Manufacturer=Fibocom Wireless Inc.
S: Product=FG650 Module
S: SerialNumber=0123456789ABCDEF
C: #Ifs= 5 Cfg#= 1 Atr=c0 MxPwr=504mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=06 Prot=00 Driver=cdc_ether
E: Ad=82(I) Atr=03(Int.) MxPS= 16 Ivl=32ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
E: Ad=01(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=02(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=83(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I: If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=03(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=84(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I: If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=04(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=85(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
NCM:
T: Bus=04 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 6 Spd=5000 MxCh= 0
D: Ver= 3.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 9 #Cfgs= 1
P: Vendor=2cb7 ProdID=0a05 Rev=04.04
S: Manufacturer=Fibocom Wireless Inc.
S: Product=FG650 Module
S: SerialNumber=0123456789ABCDEF
C: #Ifs= 6 Cfg#= 1 Atr=c0 MxPwr=504mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0d Prot=00 Driver=cdc_ncm
E: Ad=82(I) Atr=03(Int.) MxPS= 16 Ivl=32ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=01 Driver=cdc_ncm
E: Ad=01(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=02(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=83(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I: If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=03(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=84(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I: If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=04(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=85(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I: If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=05(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=86(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
RNDIS:
T: Bus=04 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 4 Spd=5000 MxCh= 0
D: Ver= 3.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 9 #Cfgs= 1
P: Vendor=2cb7 ProdID=0a06 Rev=04.04
S: Manufacturer=Fibocom Wireless Inc.
S: Product=FG650 Module
S: SerialNumber=0123456789ABCDEF
C: #Ifs= 6 Cfg#= 1 Atr=c0 MxPwr=504mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=e0(wlcon) Sub=01 Prot=03 Driver=rndis_host
E: Ad=82(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
I: If#= 1 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=rndis_host
E: Ad=01(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=02(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=83(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I: If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=03(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=84(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I: If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=04(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=85(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I: If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=05(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=86(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
MBIM:
T: Bus=04 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 7 Spd=5000 MxCh= 0
D: Ver= 3.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 9 #Cfgs= 1
P: Vendor=2cb7 ProdID=0a07 Rev=04.04
S: Manufacturer=Fibocom Wireless Inc.
S: Product=FG650 Module
S: SerialNumber=0123456789ABCDEF
C: #Ifs= 6 Cfg#= 1 Atr=c0 MxPwr=504mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim
E: Ad=82(I) Atr=03(Int.) MxPS= 64 Ivl=32ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
E: Ad=01(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=02(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=83(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I: If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=03(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=84(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I: If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=04(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=85(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I: If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=05(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=86(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 356952b13af5b2c338df1e06889fd1b5e12cbbf4 upstream.
Update the USB serial option driver support for the Fibocom
FM135-GL LTE modules.
- VID:PID 2cb7:0115, FM135-GL for laptop debug M.2 cards(with MBIM
interface for /Linux/Chrome OS)
0x0115: mbim, diag, at, pipe
Here are the outputs of usb-devices:
T: Bus=01 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 16 Spd=480 MxCh= 0
D: Ver= 2.01 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=2cb7 ProdID=0115 Rev=05.15
S: Manufacturer=Fibocom Wireless Inc.
S: Product=Fibocom Module
S: SerialNumber=12345678
C: #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim
E: Ad=82(I) Atr=03(Int.) MxPS= 64 Ivl=32ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=usbfs
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Signed-off-by: bolan wang <bolan.wang@fibocom.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1be3226445362bfbf461c92a5bcdb1723f2e4907 upstream.
The mitigation was intended to stop the irq completely. That may be
better than a hard lock-up but it turns out that you get a crash anyway
if you're using pmac_zilog as a serial console:
ttyPZ0: pmz: rx irq flood !
BUG: spinlock recursion on CPU#0, swapper/0
That's because the pr_err() call in pmz_receive_chars() results in
pmz_console_write() attempting to lock a spinlock already locked in
pmz_interrupt(). With CONFIG_DEBUG_SPINLOCK=y, this produces a fatal
BUG splat. The spinlock in question is the one in struct uart_port.
Even when it's not fatal, the serial port rx function ceases to work.
Also, the iteration limit doesn't play nicely with QEMU, as can be
seen in the bug report linked below.
A web search for other reports of the error message "pmz: rx irq flood"
didn't produce anything. So I don't think this code is needed any more.
Remove it.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Christophe Leroy <christophe.leroy@csgroup.eu>
Cc: Aneesh Kumar K.V <aneesh.kumar@kernel.org>
Cc: Naveen N. Rao <naveen.n.rao@linux.ibm.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: stable@kernel.org
Cc: linux-m68k@lists.linux-m68k.org
Link: https://github.com/vivier/qemu-m68k/issues/44
Link: https://lore.kernel.org/all/1078874617.9746.36.camel@gaston/
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Cc: stable <stable@kernel.org>
Signed-off-by: Finn Thain <fthain@linux-m68k.org>
Link: https://lore.kernel.org/r/e853cf2c762f23101cd2ddec0cc0c2be0e72685f.1712568223.git.fthain@linux-m68k.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d1718530e3f640b7d5f0050e725216eab57a85d8 upstream.
While vmk80xx does have endpoint checking implemented, some things
can fall through the cracks. Depending on the hardware model,
URBs can have either bulk or interrupt type, and current version
of vmk80xx_find_usb_endpoints() function does not take that fully
into account. While this warning does not seem to be too harmful,
at the very least it will crash systems with 'panic_on_warn' set on
them.
Fix the issue found by Syzkaller [1] by somewhat simplifying the
endpoint checking process with usb_find_common_endpoints() and
ensuring that only expected endpoint types are present.
This patch has not been tested on real hardware.
[1] Syzkaller report:
usb 1-1: BOGUS urb xfer, pipe 1 != type 3
WARNING: CPU: 0 PID: 781 at drivers/usb/core/urb.c:504 usb_submit_urb+0xc4e/0x18c0 drivers/usb/core/urb.c:503
...
Call Trace:
<TASK>
usb_start_wait_urb+0x113/0x520 drivers/usb/core/message.c:59
vmk80xx_reset_device drivers/comedi/drivers/vmk80xx.c:227 [inline]
vmk80xx_auto_attach+0xa1c/0x1a40 drivers/comedi/drivers/vmk80xx.c:818
comedi_auto_config+0x238/0x380 drivers/comedi/drivers.c:1067
usb_probe_interface+0x5cd/0xb00 drivers/usb/core/driver.c:399
...
Similar issue also found by Syzkaller:
Link: https://syzkaller.appspot.com/bug?extid=5205eb2f17de3e01946e
Reported-and-tested-by: syzbot+5f29dc6a889fc42bd896@syzkaller.appspotmail.com
Cc: stable <stable@kernel.org>
Fixes: 49253d542cc0 ("staging: comedi: vmk80xx: factor out usb endpoint detection")
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Nikita Zhandarovich <n.zhandarovich@fintech.ru>
Link: https://lore.kernel.org/r/20240408171633.31649-1-n.zhandarovich@fintech.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c38fa07dc69f0b9e6f43ecab96dc7861a70c827c upstream.
Currently we don't configure correctly the wake events after unplug of device
router. What can happen is that the downstream ports of host router will be
configured to wake on: USB4-wake and wake-on-disconnect, but not on
wake-on-connect. This may cause the later plugged device not to wake the
domain and fail in enumeration. Fix this by clearing downstream port's "USB4
Port is Configured" bit, after unplug of a device router.
Signed-off-by: Gil Fine <gil.fine@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit dcd12acaf384c30437fa5a9a1f71df06fc9835fd upstream.
Currently we notify PM core about occurred wakes after any resume. This
is not actually needed after resume from runtime suspend. Hence, notify
PM core about occurred wakes only after resume from system sleep. Also,
if the wake occurred in USB4 router upstream port, we don't notify the
PM core about it since it is not actually needed and can cause
unexpected autowake (e.g. if /sys/power/wakeup_count is used).
While there add the missing kernel-doc for tb_switch_resume().
Signed-off-by: Gil Fine <gil.fine@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 9543f6e26634537997b6e909c20911b7bf4876de ]
Fix cpuid_deps[] to list the correct dependencies for GFNI, VAES, and
VPCLMULQDQ. These features don't depend on AVX512, and there exist CPUs
that support these features but not AVX512. GFNI actually doesn't even
depend on AVX.
This prevents GFNI from being unnecessarily disabled if AVX is disabled
to mitigate the GDS vulnerability.
This also prevents all three features from being unnecessarily disabled
if AVX512VL (or its dependency AVX512F) were to be disabled, but it
looks like there isn't any case where this happens anyway.
Fixes: c128dbfa0f87 ("x86/cpufeatures: Enable new SSE/AVX/AVX512 CPU features")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Acked-by: Dave Hansen <dave.hansen@linux.intel.com>
Link: https://lore.kernel.org/r/20240417060434.47101-1-ebiggers@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 69129794d94c544810e68b2b4eaa7e44063f9bf2 ]
Confusingly, X86_FEATURE_RETPOLINE doesn't mean retpolines are enabled,
as it also includes the original "AMD retpoline" which isn't a retpoline
at all.
Also replace cpu_feature_enabled() with boot_cpu_has() because this is
before alternatives are patched and cpu_feature_enabled()'s fallback
path is slower than plain old boot_cpu_has().
Fixes: ec9404e40e8f ("x86/bhi: Add BHI mitigation knob")
Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Pawan Gupta <pawan.kumar.gupta@linux.intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: https://lore.kernel.org/r/ad3807424a3953f0323c011a643405619f2a4927.1712944776.git.jpoimboe@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e581cf5d216289ef292d1a4036d53ce90e122469 ]
Doug reported [1] the following hung task:
INFO: task swapper/0:1 blocked for more than 122 seconds.
Not tainted 5.15.149-21875-gf795ebc40eb8 #1
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
task:swapper/0 state:D stack: 0 pid: 1 ppid: 0 flags:0x00000008
Call trace:
__switch_to+0xf4/0x1f4
__schedule+0x418/0xb80
schedule+0x5c/0x10c
rpm_resume+0xe0/0x52c
rpm_resume+0x178/0x52c
__pm_runtime_resume+0x58/0x98
clk_pm_runtime_get+0x30/0xb0
clk_disable_unused_subtree+0x58/0x208
clk_disable_unused_subtree+0x38/0x208
clk_disable_unused_subtree+0x38/0x208
clk_disable_unused_subtree+0x38/0x208
clk_disable_unused_subtree+0x38/0x208
clk_disable_unused+0x4c/0xe4
do_one_initcall+0xcc/0x2d8
do_initcall_level+0xa4/0x148
do_initcalls+0x5c/0x9c
do_basic_setup+0x24/0x30
kernel_init_freeable+0xec/0x164
kernel_init+0x28/0x120
ret_from_fork+0x10/0x20
INFO: task kworker/u16:0:9 blocked for more than 122 seconds.
Not tainted 5.15.149-21875-gf795ebc40eb8 #1
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
task:kworker/u16:0 state:D stack: 0 pid: 9 ppid: 2 flags:0x00000008
Workqueue: events_unbound deferred_probe_work_func
Call trace:
__switch_to+0xf4/0x1f4
__schedule+0x418/0xb80
schedule+0x5c/0x10c
schedule_preempt_disabled+0x2c/0x48
__mutex_lock+0x238/0x488
__mutex_lock_slowpath+0x1c/0x28
mutex_lock+0x50/0x74
clk_prepare_lock+0x7c/0x9c
clk_core_prepare_lock+0x20/0x44
clk_prepare+0x24/0x30
clk_bulk_prepare+0x40/0xb0
mdss_runtime_resume+0x54/0x1c8
pm_generic_runtime_resume+0x30/0x44
__genpd_runtime_resume+0x68/0x7c
genpd_runtime_resume+0x108/0x1f4
__rpm_callback+0x84/0x144
rpm_callback+0x30/0x88
rpm_resume+0x1f4/0x52c
rpm_resume+0x178/0x52c
__pm_runtime_resume+0x58/0x98
__device_attach+0xe0/0x170
device_initial_probe+0x1c/0x28
bus_probe_device+0x3c/0x9c
device_add+0x644/0x814
mipi_dsi_device_register_full+0xe4/0x170
devm_mipi_dsi_device_register_full+0x28/0x70
ti_sn_bridge_probe+0x1dc/0x2c0
auxiliary_bus_probe+0x4c/0x94
really_probe+0xcc/0x2c8
__driver_probe_device+0xa8/0x130
driver_probe_device+0x48/0x110
__device_attach_driver+0xa4/0xcc
bus_for_each_drv+0x8c/0xd8
__device_attach+0xf8/0x170
device_initial_probe+0x1c/0x28
bus_probe_device+0x3c/0x9c
deferred_probe_work_func+0x9c/0xd8
process_one_work+0x148/0x518
worker_thread+0x138/0x350
kthread+0x138/0x1e0
ret_from_fork+0x10/0x20
The first thread is walking the clk tree and calling
clk_pm_runtime_get() to power on devices required to read the clk
hardware via struct clk_ops::is_enabled(). This thread holds the clk
prepare_lock, and is trying to runtime PM resume a device, when it finds
that the device is in the process of resuming so the thread schedule()s
away waiting for the device to finish resuming before continuing. The
second thread is runtime PM resuming the same device, but the runtime
resume callback is calling clk_prepare(), trying to grab the
prepare_lock waiting on the first thread.
This is a classic ABBA deadlock. To properly fix the deadlock, we must
never runtime PM resume or suspend a device with the clk prepare_lock
held. Actually doing that is near impossible today because the global
prepare_lock would have to be dropped in the middle of the tree, the
device runtime PM resumed/suspended, and then the prepare_lock grabbed
again to ensure consistency of the clk tree topology. If anything
changes with the clk tree in the meantime, we've lost and will need to
start the operation all over again.
Luckily, most of the time we're simply incrementing or decrementing the
runtime PM count on an active device, so we don't have the chance to
schedule away with the prepare_lock held. Let's fix this immediate
problem that can be triggered more easily by simply booting on Qualcomm
sc7180.
Introduce a list of clk_core structures that have been registered, or
are in the process of being registered, that require runtime PM to
operate. Iterate this list and call clk_pm_runtime_get() on each of them
without holding the prepare_lock during clk_disable_unused(). This way
we can be certain that the runtime PM state of the devices will be
active and resumed so we can't schedule away while walking the clk tree
with the prepare_lock held. Similarly, call clk_pm_runtime_put() without
the prepare_lock held to properly drop the runtime PM reference. We
remove the calls to clk_pm_runtime_{get,put}() in this path because
they're superfluous now that we know the devices are runtime resumed.
Reported-by: Douglas Anderson <dianders@chromium.org>
Closes: https://lore.kernel.org/all/20220922084322.RFC.2.I375b6b9e0a0a5348962f004beb3dafee6a12dfbb@changeid/ [1]
Closes: https://issuetracker.google.com/328070191
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Fixes: 9a34b45397e5 ("clk: Add support for runtime PM")
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20240325184204.745706-5-sboyd@kernel.org
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9d05ae531c2cff20d5d527f04e28d28e04379929 ]
Initialize this kref once we allocate memory for the struct clk_core so
that we can reuse the release function to free any memory associated
with the structure. This mostly consolidates code, but also clarifies
that the kref lifetime exists once the container structure (struct
clk_core) is allocated instead of leaving it in a half-baked state for
most of __clk_core_init().
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20240325184204.745706-4-sboyd@kernel.org
Stable-dep-of: e581cf5d2162 ("clk: Get runtime PM before walking tree during disable_unused")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 12ca59b91d04df32e41be5a52f0cabba912c11de ]
Currently, the regulator framework informs us before calling into
their unused cleanup paths, which eases at least some debugging. The
same could be beneficial for clocks, so that random shutdowns shortly
after most initcalls are done can be less of a guess.
Add a pr_info before disabling unused clocks to do so.
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230307132928.3887737-1-konrad.dybcio@linaro.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Stable-dep-of: e581cf5d2162 ("clk: Get runtime PM before walking tree during disable_unused")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 79806d338829b2bf903480428d8ce5aab8e2d24b ]
Remove extra empty line.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220630151205.3935560-1-claudiu.beznea@microchip.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Stable-dep-of: e581cf5d2162 ("clk: Get runtime PM before walking tree during disable_unused")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 75061a6ff49ba3482c6319ded0c26e6a526b0967 ]
This list array doesn't change at runtime. Mark it const to move to RO
memory.
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20220217220554.2711696-2-sboyd@kernel.org
Stable-dep-of: e581cf5d2162 ("clk: Get runtime PM before walking tree during disable_unused")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8358a76cfb47c9a5af627a0c4e7168aa14fa25f6 ]
Removing this assertion lets us move the kref_put() call outside the
prepare_lock section. We don't need to hold the prepare_lock here to
free memory and destroy the clk_core structure. We've already unlinked
the clk from the clk tree and by the time the release function runs
nothing holds a reference to the clk_core anymore so anything with the
pointer can't access the memory that's being freed anyway. Way back in
commit 496eadf821c2 ("clk: Use lockdep asserts to find missing hold of
prepare_lock") we didn't need to have this assertion either.
Fixes: 496eadf821c2 ("clk: Use lockdep asserts to find missing hold of prepare_lock")
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20240325184204.745706-2-sboyd@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9e4d3f4f34455abbaa9930bf6b7575a5cd081496 ]
The DSI device for the panel was registered by the DSI host, so it is an
error to unregister it from the panel driver. Drop the call to
mipi_dsi_device_unregister().
Fixes: c7f66d32dd43 ("drm/panel: add support for rm69299 visionox panel")
Reviewed-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240404-drop-panel-unregister-v1-1-9f56953c5fb9@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit cf92bb778eda7830e79452c6917efa8474a30c1e ]
When Output Resource (dcb->or) value is assigned in
fabricate_dcb_output(), there may be out of bounds access to
dac_users array in case dcb->or is zero because ffs(dcb->or) is
used as index there.
The 'or' argument of fabricate_dcb_output() must be interpreted as a
number of bit to set, not value.
Utilize macros from 'enum nouveau_or' in calls instead of hardcoding.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 2e5702aff395 ("drm/nouveau: fabricate DCB encoder table for iMac G4")
Fixes: 670820c0e6a9 ("drm/nouveau: Workaround incorrect DCB entry on a GeForce3 Ti 200.")
Signed-off-by: Mikhail Kobuk <m.kobuk@ispras.ru>
Signed-off-by: Danilo Krummrich <dakr@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240411110854.16701-1-m.kobuk@ispras.ru
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2d8527f2f911fab84aec04df4788c0c23af3df48 ]
A race condition exists in ccw_device_set_online() that can cause the
online process to fail, leaving the affected device in an inconsistent
state. As a result, subsequent attempts to set that device online fail
with return code ENODEV.
The problem occurs when a path verification request arrives after
a wait for final device state completed, but before the result state
is evaluated.
Fix this by ensuring that the CCW-device lock is held between
determining final state and checking result state.
Note that since:
commit 2297791c92d0 ("s390/cio: dont unregister subchannel from child-drivers")
path verification requests are much more likely to occur during boot,
resulting in an increased chance of this race condition occurring.
Fixes: 2297791c92d0 ("s390/cio: dont unregister subchannel from child-drivers")
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Reviewed-by: Vineeth Vijayan <vneethv@linux.ibm.com>
Signed-off-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 607638faf2ff1cede37458111496e7cc6c977f6f ]
A deferred condition code 1 response indicates that I/O was not started
and should be retried. The current QDIO implementation handles a cc1
response as I/O error, resulting in a failed QDIO setup. This can happen
for example when a path verification request arrives at the same time
as QDIO setup I/O is started.
Fix this by retrying the QDIO setup I/O when a cc1 response is received.
Note that since
commit 2297791c92d0 ("s390/cio: dont unregister subchannel from child-drivers")
commit 5ef1dc40ffa6 ("s390/cio: fix invalid -EBUSY on ccw_device_start")
deferred cc1 responses are much more likely to occur. See the commit
message of the latter for more background information.
Fixes: 2297791c92d0 ("s390/cio: dont unregister subchannel from child-drivers")
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit be121ffb384f53e966ee7299ffccc6eeb61bc73d ]
Set the correct port when querying PPCNT in multi-port configuration.
Distinguish between cases where switchdev mode was enabled to multi-port
configuration and don't overwrite the queried port to 1 in multi-port
case.
Fixes: 74b30b3ad5ce ("RDMA/mlx5: Set local port to one when accessing counters")
Signed-off-by: Michael Guralnik <michaelgur@nvidia.com>
Link: https://lore.kernel.org/r/9bfcc8ade958b760a51408c3ad654a01b11f7d76.1712134988.git.leon@kernel.org
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b68e1acb5834ed1a2ad42d9d002815a8bae7c0b6 ]
The old state is helpful for debugging, as the current state is always
IB_CM_IDLE when timeout happens.
Fixes: 96d9cbe2f2ff ("RDMA/cm: add timeout to cm_destroy_id wait")
Signed-off-by: Mark Zhang <markzhang@nvidia.com>
Link: https://lore.kernel.org/r/20240322112049.2022994-1-markzhang@nvidia.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 481047d7e8391d3842ae59025806531cdad710d9 ]
When a mutex lock is not used any more, the function mutex_destroy
should be called to mark the mutex lock uninitialized.
Fixes: 8700e3e7c485 ("Soft RoCE driver")
Signed-off-by: Yanjun.Zhu <yanjun.zhu@linux.dev>
Link: https://lore.kernel.org/r/20240314065140.27468-1-yanjun.zhu@linux.dev
Reviewed-by: Daisuke Matsuda <matsuda-daisuke@fujitsu.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c24cd679b075b0e953ea167b0aa2b2d59e4eba7f ]
The TX and RX DMA Channels used by the driver to exchange data with CPSW
are not guaranteed to be in a clean state during driver initialization.
The Bootloader could have used the same DMA Channels without cleaning them
up in the event of failure. Thus, reset and disable the DMA Channels to
ensure that they are in a clean state before using them.
Fixes: 93a76530316a ("net: ethernet: ti: introduce am65x/j721e gigabit eth subsystem driver")
Reported-by: Schuyler Patton <spatton@ti.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20240417095425.2253876-1-s-vadapalli@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit d59cf049c8378677053703e724808836f180888e ]
This switch intellectual property provides a bit on the ARL global control
register which controls allowing mirroring frames which are received on the
local port (monitor port). This bit is unset after reset.
This ability must be enabled to fully support the port mirroring feature on
this switch intellectual property.
Therefore, this patch fixes the traffic not being reflected on a port,
which would be configured like below:
tc qdisc add dev swp0 clsact
tc filter add dev swp0 ingress matchall skip_sw \
action mirred egress mirror dev swp0
As a side note, this configuration provides the hairpinning feature for a
single port.
Fixes: 37feab6076aa ("net: dsa: mt7530: add support for port mirroring")
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
Bruce Ashfield
Greg Kroah-Hartman
Arınç ÜNAL
Vladimir Oltean
Jeongjun Park
Dave Airlie
Zack Rusin
xinhui pan
Carlos Llamas
Yuntao Wang
Yaxiong Tian
Sandipan Das
Sean Christopherson
Alan Stern
Samuel Thibault
Alexander Usyskin
Norihiko Hama
Kai-Heng Feng
Minas Harutyunyan
Daniele Palmas
Vanillan Wang
Jerry Meng
Coia Prant
Chuanhong Guo
bolan wang
Finn Thain
Nikita Zhandarovich
Gil Fine
Eric Biggers
Josh Poimboeuf
Stephen Boyd
Konrad Dybcio
Claudiu Beznea
Dmitry Baryshkov
Mikhail Kobuk
Peter Oberparleiter
Michael Guralnik
Mark Zhang
Yanjun.Zhu
Siddharth Vadapalli