| Age | Commit message (Collapse) | Author |
|---|
|
commit a3238924a820c1d7c977b632b769f3b5690cba09 upstream.
The maximum voltage value for buck8 regulator on Odroid XU3/XU4 boards is
set too low. Increase it to the 2000mV as specified on the board schematic.
So far the board worked fine, because of the bug in the PMIC driver, which
used incorrect step value for that regulator. It interpreted the voltage
value set by the bootloader as 1225mV and kept it unchanged. The regulator
driver has been however fixed recently in the commit 56b5d4ea778c
("regulator: s2mps11: Fix steps for buck7, buck8 and LDO35"), what results
in reading the proper buck8 value and forcing it to 1500mV on boot. This
is not enough for proper board operation and results in eMMC errors during
heavy IO traffic. Increasing maximum voltage value for buck8 restores
original driver behavior and fixes eMMC issues.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Fixes: 86a2d2ac5e5d ("ARM: dts: Add dts file for Odroid XU3 board")
Fixes: 56b5d4ea778c ("regulator: s2mps11: Fix steps for buck7, buck8 and LDO35")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a66352e005488ecb4b534ba1af58a9f671eba9b8 upstream.
Add minimal parameters needed by the Exynos CLKOUT driver to Exynos3250
PMU node. This fixes the following warning on boot:
exynos_clkout_init: failed to register clkout clock
Fixes: d19bb397e19e ("ARM: dts: exynos: Update PMU node with CLKOUT related data")
Cc: <stable@vger.kernel.org>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ec33745bccc8f336957c751f4153421cc9ef5a54 upstream.
Commit 225da7e65a03 ("ARM: dts: add eMMC reset line for
exynos4412-odroid-common") added MMC power sequence for eMMC card of
Odroid X2/U3. It reused generic sd1_cd pin control configuration node
and only disabled pull-up. However that time the pinctrl configuration
was not applied during MMC power sequence driver initialization. This
has been changed later by commit d97a1e5d7cd2 ("mmc: pwrseq: convert to
proper platform device").
It turned out then, that the provided pinctrl configuration is not
correct, because the eMMC_RTSN line is being re-configured as 'special
function/card detect function for mmc1 controller' not the simple
'output', thus the power sequence driver doesn't really set the pin
value. This in effect broke the reboot of Odroid X2/U3 boards. Fix this
by providing separate node with eMMC_RTSN pin configuration.
Cc: <stable@vger.kernel.org>
Reported-by: Markus Reichl <m.reichl@fivetechno.de>
Suggested-by: Ulf Hansson <ulf.hansson@linaro.org>
Fixes: 225da7e65a03 ("ARM: dts: add eMMC reset line for exynos4412-odroid-common")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8d26c1390aec795d492b8de5e4437751e8805a1d upstream.
This reverts commit abd7d0972a192ee653efc7b151a6af69db58f2bb. This
change was already partially reverted by John Stultz in
commit 9c6d26df1fae ("arm64: dts: hikey: Fix eMMC corruption regression").
This change appears to cause controller resets and block read failures
which prevents successful booting on some hikey boards.
Cc: Ryan Grachek <ryan@edited.us>
Cc: Wei Xu <xuwei5@hisilicon.com>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: devicetree@vger.kernel.org
Cc: stable <stable@vger.kernel.org> #4.17+
Signed-off-by: Alistair Strachan <astrachan@google.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 83b944174ad79825ae84a47af1a0354485b24602 upstream.
Somewhere along recent changes to power control of the wl1835, power-on
became very unreliable on the hikey, failing like this:
wl1271_sdio: probe of mmc2:0001:1 failed with error -16
wl1271_sdio: probe of mmc2:0001:2 failed with error -16
After playing with some dt parameters and comparing to other users of
this chip, it turned out we need some power-on delay to make things
stable again. In contrast to those other users which define 200 ms, the
hikey would already be happy with 1 ms. Still, we use the safer 10 ms,
like on the Ultra96.
Fixes: ea452678734e ("arm64: dts: hikey: Fix WiFi support")
Cc: <stable@vger.kernel.org> #4.12+
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 35a4f89cd4731ac6ec985cd29ddc1630903006b7 upstream.
Somewhere along recent changes to power control of the wl1831, power-on
became very unreliable on the Ultra96, failing like this:
wl1271_sdio: probe of mmc2:0001:1 failed with error -16
wl1271_sdio: probe of mmc2:0001:2 failed with error -16
After playing with some dt parameters and comparing to other users of
this chip, it turned out we need some power-on delay to make things
stable again. In contrast to those other users which define 200 ms,
Ultra96 is already happy with 10 ms.
Fixes: 5869ba0653b9 ("arm64: zynqmp: Add support for Xilinx zcu100-revC")
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2e095ce7b6ecce2f3e2ff330527f12056ed1e1a1 upstream.
On Denverton's integration of the Intel(R) Trace Hub (for a reference and
overview see Documentation/trace/intel_th.rst) the reported size of one of
its resources (RTIT_BAR) doesn't match its actual size, which leads to
overlaps with other devices' resources.
In practice, it overlaps with XHCI MMIO space, which results in the xhci
driver bailing out after seeing its registers as 0xffffffff, and perceived
disappearance of all USB devices:
intel_th_pci 0000:00:1f.7: enabling device (0004 -> 0006)
xhci_hcd 0000:00:15.0: xHCI host controller not responding, assume dead
xhci_hcd 0000:00:15.0: xHC not responding in xhci_irq, assume controller is dead
xhci_hcd 0000:00:15.0: HC died; cleaning up
usb 1-1: USB disconnect, device number 2
For this reason, we need to resize the RTIT_BAR on Denverton to its actual
size, which in this case is 4MB. The corresponding erratum is DNV36 at the
link below:
DNV36. Processor Host Root Complex May Incorrectly Route Memory
Accesses to Intel® Trace Hub
Problem: The Intel® Trace Hub RTIT_BAR (B0:D31:F7 offset 20h) is
reported as a 2KB memory range. Due to this erratum, the
processor Host Root Complex will forward addresses from
RTIT_BAR to RTIT_BAR + 4MB -1 to Intel® Trace Hub.
Implication: Devices assigned within the RTIT_BAR to RTIT_BAR + 4MB -1
space may not function correctly.
Workaround: A BIOS code change has been identified and may be
implemented as a workaround for this erratum.
Status: No Fix.
Note that 5118ccd34780 ("intel_th: pci: Add Denverton SOC support") updates
the Trace Hub driver so it claims the Denverton device, but the resource
overlap exists regardless of whether that driver is loaded or that commit
is included.
Link: https://www.intel.com/content/dam/www/public/us/en/documents/specification-updates/atom-c3000-family-spec-update.pdf
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
[bhelgaas: include erratum text, clarify relationship with 5118ccd34780]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5e420fe635813e5746b296cfc8fff4853ae205a2 upstream.
Add missing break statement and fix identation issue.
This bug was found thanks to the ongoing efforts to enable
-Wimplicit-fallthrough.
Fixes: 9cb62fa24e0d ("aacraid: Log firmware AIF messages")
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit df997abeebadaa4824271009e2d2b526a70a11cb upstream.
Add missing break statement in order to prevent the code from falling
through to case ISCSI_BOOT_TGT_NAME, which is unnecessary.
This bug was found thanks to the ongoing efforts to enable
-Wimplicit-fallthrough.
Fixes: b33a84a38477 ("ibft: convert iscsi_ibft module to iscsi boot lib")
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e154ab69321ce2c54f19863d75c77b4e2dc9d365 upstream.
Lenovo s21e-20 uses ELAN0601 in its ACPI tables for the Elan touchpad.
Signed-off-by: Vincent Batts <vbatts@hashbangbash.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 44fc95e218a09d7966a9d448941fdb003f6bb69f upstream.
Tablet initially begins communicating at 9600 baud, so this command
should be used to connect to the device:
$ inputattach --daemon --baud 9600 --wacom_iv /dev/ttyS0
https://github.com/linuxwacom/xf86-input-wacom/issues/40
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 4726bcf30fad37cc555cd9dcd6c73f2b2668c879 ]
The reset work holds a mutex to prevent races with removal modifying the
same resources, but was unlocking only on success. Unlock on failure
too.
Fixes: 5c959d73dba64 ("nvme-pci: fix rapid add remove sequence")
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8c772a9bfc7c07c76f4a58b58910452fbb20843b ]
Our test reported the following stack, and vmcore showed that
->inflight counter is -1.
[ffffc9003fcc38d0] __schedule at ffffffff8173d95d
[ffffc9003fcc3958] schedule at ffffffff8173de26
[ffffc9003fcc3970] io_schedule at ffffffff810bb6b6
[ffffc9003fcc3988] blkcg_iolatency_throttle at ffffffff813911cb
[ffffc9003fcc3a20] rq_qos_throttle at ffffffff813847f3
[ffffc9003fcc3a48] blk_mq_make_request at ffffffff8137468a
[ffffc9003fcc3b08] generic_make_request at ffffffff81368b49
[ffffc9003fcc3b68] submit_bio at ffffffff81368d7d
[ffffc9003fcc3bb8] ext4_io_submit at ffffffffa031be00 [ext4]
[ffffc9003fcc3c00] ext4_writepages at ffffffffa03163de [ext4]
[ffffc9003fcc3d68] do_writepages at ffffffff811c49ae
[ffffc9003fcc3d78] __filemap_fdatawrite_range at ffffffff811b6188
[ffffc9003fcc3e30] filemap_write_and_wait_range at ffffffff811b6301
[ffffc9003fcc3e60] ext4_sync_file at ffffffffa030cee8 [ext4]
[ffffc9003fcc3ea8] vfs_fsync_range at ffffffff8128594b
[ffffc9003fcc3ee8] do_fsync at ffffffff81285abd
[ffffc9003fcc3f18] sys_fsync at ffffffff81285d50
[ffffc9003fcc3f28] do_syscall_64 at ffffffff81003c04
[ffffc9003fcc3f50] entry_SYSCALL_64_after_swapgs at ffffffff81742b8e
The ->inflight counter may be negative (-1) if
1) blk-iolatency was disabled when the IO was issued,
2) blk-iolatency was enabled before this IO reached its endio,
3) the ->inflight counter is decreased from 0 to -1 in endio()
In fact the hang can be easily reproduced by the below script,
H=/sys/fs/cgroup/unified/
P=/sys/fs/cgroup/unified/test
echo "+io" > $H/cgroup.subtree_control
mkdir -p $P
echo $$ > $P/cgroup.procs
xfs_io -f -d -c "pwrite 0 4k" /dev/sdg
echo "`cat /sys/block/sdg/dev` target=1000000" > $P/io.latency
xfs_io -f -d -c "pwrite 0 4k" /dev/sdg
This fixes the problem by freezing the queue so that while
enabling/disabling iolatency, there is no inflight rq running.
Note that quiesce_queue is not needed as this only updating iolatency
configuration about which dispatching request_queue doesn't care.
Signed-off-by: Liu Bo <bo.liu@linux.alibaba.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0aa4febb420d91df5b56b1864a2465765da85f4b ]
Under heavy traffic load, when changing number of channels via
ethtool (ethtool -L) which will cause interface to be reloaded,
it was observed that some packets gets transmitted on old TX
channel/queue id which doesn't really exist after the channel
configuration leads to system crash.
Add a safeguard in the driver by validating queue id through
ndo_select_queue() which is called before the ndo_start_xmit().
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit fb1faab74ddef9ec2d841d54e5d0912a097b3abe ]
Max supported queues is derived incorrectly in the case of multi-CoS.
Need to consider TCs while calculating num_queues for PF.
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 660492bcf4a7561b5fdc13be0ae0b0c0a8c120be ]
When slowpath messages are sent with high rate, the resulting
events can lead to a FW assert in case they are not handled fast
enough (Event Queue Full assert). Attempt to send queued slowpath
messages only after the newly evacuated entries in the EQ ring
are indicated to FW.
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 43636c804df0126da669c261fc820fb22f62bfc2 ]
When something let __find_get_block_slow() hit all_mapped path, it calls
printk() for 100+ times per a second. But there is no need to print same
message with such high frequency; it is just asking for stall warning, or
at least bloating log files.
[ 399.866302][T15342] __find_get_block_slow() failed. block=1, b_blocknr=8
[ 399.873324][T15342] b_state=0x00000029, b_size=512
[ 399.878403][T15342] device loop0 blocksize: 4096
[ 399.883296][T15342] __find_get_block_slow() failed. block=1, b_blocknr=8
[ 399.890400][T15342] b_state=0x00000029, b_size=512
[ 399.895595][T15342] device loop0 blocksize: 4096
[ 399.900556][T15342] __find_get_block_slow() failed. block=1, b_blocknr=8
[ 399.907471][T15342] b_state=0x00000029, b_size=512
[ 399.912506][T15342] device loop0 blocksize: 4096
This patch reduces frequency to up to once per a second, in addition to
concatenating three lines into one.
[ 399.866302][T15342] __find_get_block_slow() failed. block=1, b_blocknr=8, b_state=0x00000029, b_size=512, device loop0 blocksize: 4096
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Reviewed-by: Jan Kara <jack@suse.cz>
Cc: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5c959d73dba6495ec01d04c206ee679d61ccb2b0 ]
A surprise removal may fail to tear down request queues if it is racing
with the initial asynchronous probe. If that happens, the remove path
won't see the queue resources to tear down, and the controller reset
path may create a new request queue on a removed device, but will not
be able to make forward progress, deadlocking the pci removal.
Protect setting up non-blocking resources from a shutdown by holding the
same mutex, and transition to the CONNECTING state after these resources
are initialized so the probe path may see the dead controller state
before dispatching new IO.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=202081
Reported-by: Alex Gagniuc <Alex_Gagniuc@Dellteam.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Tested-by: Alex Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e7ad43c3eda6a1690c4c3c341f95dc1c6898da83 ]
If a controller supports the NS Change Notification, the namespace
scan_work is automatically triggered after attaching a new namespace.
Occasionally the namespace scan_work may append the new namespace to the
list before the admin command effects handling is completed. The effects
handling unfreezes namespaces, but if it unfreezes the newly attached
namespace, its request_queue freeze depth will be off and we'll hit the
warning in blk_mq_unfreeze_queue().
On the next namespace add, we will fail to freeze that queue due to the
previous bad accounting and deadlock waiting for frozen.
Fix that by preventing scan work from altering the namespace list while
command effects handling needs to pair freeze with unfreeze.
Reported-by: Wen Xiong <wenxiong@us.ibm.com>
Tested-by: Wen Xiong <wenxiong@us.ibm.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0a5f49cbf9d6ad3721c16f8a6d823363ea7a160f ]
amdgpu_vm_get_task_info is called from interrupt handler and sched timeout
workqueue, we should use irq version spin_lock to avoid deadlock.
Signed-off-by: Philip Yang <Philip.Yang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c6e2bd956936d925748581e4d0294f10f1d92f2c ]
We currently get the following error with pixcir_ts driver during a
suspend resume cycle:
omap_i2c 4802a000.i2c: controller timed out
pixcir_ts 1-005c: pixcir_int_enable: can't read reg 0x34 : -110
pixcir_ts 1-005c: Failed to disable interrupt generation: -110
pixcir_ts 1-005c: Failed to stop
dpm_run_callback(): pixcir_i2c_ts_resume+0x0/0x98
[pixcir_i2c_ts] returns -110
PM: Device 1-005c failed to resume: error -110
And at least am437x based devices with pixcir_ts will fail to resume
to a touchscreen that is configured as the wakeup-source in device
tree for these devices.
This is because pixcir_ts tries to reconfigure it's registers for
noirq suspend which fails. This also leaves i2c-omap in enabled state
for suspend.
Let's fix the pixcir_ts issue and make sure i2c-omap is suspended by
adding SET_NOIRQ_SYSTEM_SLEEP_PM_OPS.
Let's also get rid of some ifdefs while at it and replace them with
__maybe_unused as SET_RUNTIME_PM_OPS and SET_NOIRQ_SYSTEM_SLEEP_PM_OPS
already deal with the various PM Kconfig options.
Reported-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit d8f6382a7d026989029e2e50c515df954488459b ]
This reverts commit bbc0f8bd88abefb0f27998f40a073634a3a2db89.
It added a warning whose intent was to check whether the rport was still
linked into the peer list. It doesn't work as intended and gives false
positive warnings for two reasons:
1) If the rport is never linked into the peer list it will not be
considered empty since the list_head is never initialized.
2) If the rport is deleted from the peer list using list_del_rcu(), then
the list_head is in an undefined state and it is not considered empty.
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2b424cfc69728224fcb5fad138ea7260728e0901 ]
Patch (b6c7a324df37b "MIPS: Fix get_frame_info() handling of
microMIPS function size.") introduces additional function size
check for microMIPS by only checking insn between ip and ip + func_size.
However, func_size in get_frame_info() is always 0 if KALLSYMS is not
enabled. This causes get_frame_info() to return immediately without
calculating correct frame_size, which in turn causes "Can't analyze
schedule() prologue" warning messages at boot time.
This patch removes func_size check, and let the frame_size check run
up to 128 insns for both MIPS and microMIPS.
Signed-off-by: Jun-Ru Chang <jrjang@realtek.com>
Signed-off-by: Tony Wu <tonywu@realtek.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Fixes: b6c7a324df37b ("MIPS: Fix get_frame_info() handling of microMIPS function size.")
Cc: <ralf@linux-mips.org>
Cc: <jhogan@kernel.org>
Cc: <macro@mips.com>
Cc: <yamada.masahiro@socionext.com>
Cc: <peterz@infradead.org>
Cc: <mingo@kernel.org>
Cc: <linux-mips@vger.kernel.org>
Cc: <linux-kernel@vger.kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6ab3bc240ade47a0f52bc16d97edd9accbe0024e ]
With a suitably defined "probe:vfs_getname" probe, 'perf trace' can
"beautify" its output, so syscalls like open() or openat() can print the
"filename" argument instead of just its hex address, like:
$ perf trace -e open -- touch /dev/null
[...]
0.590 ( 0.014 ms): touch/18063 open(filename: /dev/null, flags: CREAT|NOCTTY|NONBLOCK|WRONLY, mode: IRUGO|IWUGO) = 3
[...]
The output without such beautifier looks like:
0.529 ( 0.011 ms): touch/18075 open(filename: 0xc78cf288, flags: CREAT|NOCTTY|NONBLOCK|WRONLY, mode: IRUGO|IWUGO) = 3
However, when the vfs_getname probe expands to multiple probes and it is
not the first one that is hit, the beautifier fails, as following:
0.326 ( 0.010 ms): touch/18072 open(filename: , flags: CREAT|NOCTTY|NONBLOCK|WRONLY, mode: IRUGO|IWUGO) = 3
Fix it by hooking into all the expanded probes (inlines), now, for instance:
[root@quaco ~]# perf probe -l
probe:vfs_getname (on getname_flags:73@fs/namei.c with pathname)
probe:vfs_getname_1 (on getname_flags:73@fs/namei.c with pathname)
[root@quaco ~]# perf trace -e open* sleep 1
0.010 ( 0.005 ms): sleep/5588 openat(dfd: CWD, filename: /etc/ld.so.cache, flags: RDONLY|CLOEXEC) = 3
0.029 ( 0.006 ms): sleep/5588 openat(dfd: CWD, filename: /lib64/libc.so.6, flags: RDONLY|CLOEXEC) = 3
0.194 ( 0.008 ms): sleep/5588 openat(dfd: CWD, filename: /usr/lib/locale/locale-archive, flags: RDONLY|CLOEXEC) = 3
[root@quaco ~]#
Works, further verified with:
[root@quaco ~]# perf test vfs
65: Use vfs_getname probe to get syscall args filenames : Ok
66: Add vfs_getname probe to get syscall args filenames : Ok
67: Check open filename arg using perf trace + vfs_getname: Ok
[root@quaco ~]#
Reported-by: Michael Petlan <mpetlan@redhat.com>
Tested-by: Michael Petlan <mpetlan@redhat.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Link: https://lkml.kernel.org/n/tip-mv8kolk17xla1smvmp3qabv1@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 59a17706915fe5ea6f711e1f92d4fb706bce07fe ]
When perf is built with the annobin plugin (RHEL8 build) extra symbols
are added to its binary:
# nm perf | grep annobin | head -10
0000000000241100 t .annobin_annotate.c
0000000000326490 t .annobin_annotate.c
0000000000249255 t .annobin_annotate.c_end
00000000003283a8 t .annobin_annotate.c_end
00000000001bce18 t .annobin_annotate.c_end.hot
00000000001bce18 t .annobin_annotate.c_end.hot
00000000001bc3e2 t .annobin_annotate.c_end.unlikely
00000000001bc400 t .annobin_annotate.c_end.unlikely
00000000001bce18 t .annobin_annotate.c.hot
00000000001bce18 t .annobin_annotate.c.hot
...
Those symbols have no use for report or annotation and should be
skipped. Moreover they interfere with the DWARF unwind test on the PPC
arch, where they are mixed with checked symbols and then the test fails:
# perf test dwarf -v
59: Test dwarf unwind :
--- start ---
test child forked, pid 8515
unwind: .annobin_dwarf_unwind.c:ip = 0x10dba40dc (0x2740dc)
...
got: .annobin_dwarf_unwind.c 0x10dba40dc, expecting test__arch_unwind_sample
unwind: failed with 'no error'
The annobin symbols are defined as NOTYPE/LOCAL/HIDDEN:
# readelf -s ./perf | grep annobin | head -1
40: 00000000001bce4f 0 NOTYPE LOCAL HIDDEN 13 .annobin_init.c
They can still pass the check for the label symbol. Adding check for
HIDDEN and INTERNAL (as suggested by Nick below) visibility and filter
out such symbols.
> Just to be awkward, if you are going to ignore STV_HIDDEN
> symbols then you should probably also ignore STV_INTERNAL ones
> as well... Annobin does not generate them, but you never know,
> one day some other tool might create some.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Michael Petlan <mpetlan@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Nick Clifton <nickc@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20190128133526.GD15461@krava
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c2780c1a3fb724560b1d44f7976e0de17bf153c7 ]
A card's close_dev work is scheduled on a driver-wide workqueue. If the
card is removed and freed while the work is still active, this causes a
use-after-free.
So make sure that the work is completed before freeing the card.
Fixes: 0f54761d167f ("qeth: Support VEPA mode")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit afa0c5904ba16d59b0454f7ee4c807dae350f432 ]
The error path in qeth_alloc_qdio_buffers() that takes care of
cleaning up the Output Queues is buggy. It first frees the queue, but
then calls qeth_clear_outq_buffers() with that very queue struct.
Make the call to qeth_clear_outq_buffers() part of the free action
(in the correct order), and while at it fix the naming of the helper.
Fixes: 0da9581ddb0f ("qeth: exploit asynchronous delivery of storage blocks")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5065b2dd3e5f9247a6c9d67974bc0472bf561b9d ]
Whenever we fail before/while starting an IO, make sure to release the
IO buffer. Usually qeth_irq() would do this for us, but if the IO
doesn't even start we obviously won't get an interrupt for it either.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4e35c1cb9460240e983a01745b5f29fe3a4d8e39 ]
It is possible that two concurrent packets originating from the same
socket of a connection-less protocol (e.g. UDP) can end up having
different IP_CT_DIR_REPLY tuples which results in one of the packets
being dropped.
To illustrate this, consider the following simplified scenario:
1. Packet A and B are sent at the same time from two different threads
by same UDP socket. No matching conntrack entry exists yet.
Both packets cause allocation of a new conntrack entry.
2. get_unique_tuple gets called for A. No clashing entry found.
conntrack entry for A is added to main conntrack table.
3. get_unique_tuple is called for B and will find that the reply
tuple of B is already taken by A.
It will allocate a new UDP source port for B to resolve the clash.
4. conntrack entry for B cannot be added to main conntrack table
because its ORIGINAL direction is clashing with A and the REPLY
directions of A and B are not the same anymore due to UDP source
port reallocation done in step 3.
This patch modifies nf_conntrack_tuple_taken so it doesn't consider
colliding reply tuples if the IP_CT_DIR_ORIGINAL tuples are equal.
[ Florian: simplify patch to not use .allow_clash setting
and always ignore identical flows ]
Signed-off-by: Martynas Pumputis <martynas@weave.works>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 98bfc3414bda335dbd7fec58bde6266f991801d7 ]
Check basic nat/redirect/masquerade for ipv4 and ipv6.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 952b72f89ae23b316da8c1021b18d0c388ad6cc4 ]
In selftests the config fragment for netfilter was added as
NF_TABLES_INET=y and this patch correct it as CONFIG_NF_TABLES_INET=y
Signed-off-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6454368a804c4955ccd116236037536f81e5b1f1 ]
In case of mapping error the DMA addresses are invalid and continuing
will screw system memory or potentially something else.
[ 222.480310] dmatest: dma0chan7-copy0: summary 1 tests, 3 failures 6 iops 349 KB/s (0)
...
[ 240.912725] check: Corrupted low memory at 00000000c7c75ac9 (2940 phys) = 5656000000000000
[ 240.921998] check: Corrupted low memory at 000000005715a1cd (2948 phys) = 279f2aca5595ab2b
[ 240.931280] check: Corrupted low memory at 000000002f4024c0 (2950 phys) = 5e5624f349e793cf
...
Abort any test if mapping failed.
Fixes: 4076e755dbec ("dmatest: convert to dmaengine_unmap_data")
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 85965487abc540368393a15491e6e7fcd230039d ]
When the virtio transport device disappear, we should reset all
connected sockets in order to inform the users.
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 22b5c0b63f32568e130fa2df4ba23efce3eb495b ]
virtio_vsock_remove() invokes the vsock_core_exit() also if there
are opened sockets for the AF_VSOCK protocol family. In this way
the vsock "transport" pointer is set to NULL, triggering the
kernel panic at the first socket activity.
This patch move the vsock_core_init()/vsock_core_exit() in the
virtio_vsock respectively in module_init and module_exit functions,
that cannot be invoked until there are open sockets.
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1609699
Reported-by: Yan Fu <yafu@redhat.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit dc3f595b6617ebc0307e0ce151e8f2f2b2489b95 ]
atchan->status variable is used to store two different information:
- pass channel interrupts status from interrupt handler to tasklet;
- channel information like whether it is cyclic or paused;
This causes a bug when device_terminate_all() is called,
(AT_XDMAC_CHAN_IS_CYCLIC cleared on atchan->status) and then a late End
of Block interrupt arrives (AT_XDMAC_CIS_BIS), which sets bit 0 of
atchan->status. Bit 0 is also used for AT_XDMAC_CHAN_IS_CYCLIC, so when
a new descriptor for a cyclic transfer is created, the driver reports
the channel as in use:
if (test_and_set_bit(AT_XDMAC_CHAN_IS_CYCLIC, &atchan->status)) {
dev_err(chan2dev(chan), "channel currently used\n");
return NULL;
}
This patch fixes the bug by adding a different struct member to keep
the interrupts status separated from the channel status bits.
Fixes: e1f7c9eee707 ("dmaengine: at_xdmac: creation of the atmel eXtended DMA Controller driver")
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b14e945bda8ae227d1bf2b1837c0c4a61721cd1a ]
When initializing clocks, a reference to the TCON channel 0 clock is
obtained. However, the clock is never prepared and enabled later.
Switching from simplefb to DRM actually disables the clock (that was
usually configured by U-Boot) because of that.
On the V3s, this results in a hang when writing to some mixer registers
when switching over to DRM from simplefb.
Fix this by preparing and enabling the clock when initializing other
clocks. Waiting for sun4i_tcon_channel_enable to enable the clock is
apparently too late and results in the same mixer register access hang.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190131132550.26355-1-paul.kocialkowski@bootlin.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 7c4cd051add3d00bbff008a133c936c515eaa8fe ]
The map_lookup_elem used to not acquiring spinlock
in order to optimize the reader.
It was true until commit 557c0c6e7df8 ("bpf: convert stackmap to pre-allocation")
The syscall's map_lookup_elem(stackmap) calls bpf_stackmap_copy().
bpf_stackmap_copy() may find the elem no longer needed after the copy is done.
If that is the case, pcpu_freelist_push() saves this elem for reuse later.
This push requires a spinlock.
If a tracing bpf_prog got run in the middle of the syscall's
map_lookup_elem(stackmap) and this tracing bpf_prog is calling
bpf_get_stackid(stackmap) which also requires the same pcpu_freelist's
spinlock, it may end up with a dead lock situation as reported by
Eric Dumazet in https://patchwork.ozlabs.org/patch/1030266/
The situation is the same as the syscall's map_update_elem() which
needs to acquire the pcpu_freelist's spinlock and could race
with tracing bpf_prog. Hence, this patch fixes it by protecting
bpf_stackmap_copy() with this_cpu_inc(bpf_prog_active)
to prevent tracing bpf_prog from running.
A later syscall's map_lookup_elem commit f1a2e44a3aec ("bpf: add queue and stack maps")
also acquires a spinlock and races with tracing bpf_prog similarly.
Hence, this patch is forward looking and protects the majority
of the map lookups. bpf_map_offload_lookup_elem() is the exception
since it is for network bpf_prog only (i.e. never called by tracing
bpf_prog).
Fixes: 557c0c6e7df8 ("bpf: convert stackmap to pre-allocation")
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e16ec34039c701594d55d08a5aa49ee3e1abc821 ]
Lockdep found a potential deadlock between cpu_hotplug_lock, bpf_event_mutex, and cpuctx_mutex:
[ 13.007000] WARNING: possible circular locking dependency detected
[ 13.007587] 5.0.0-rc3-00018-g2fa53f892422-dirty #477 Not tainted
[ 13.008124] ------------------------------------------------------
[ 13.008624] test_progs/246 is trying to acquire lock:
[ 13.009030] 0000000094160d1d (tracepoints_mutex){+.+.}, at: tracepoint_probe_register_prio+0x2d/0x300
[ 13.009770]
[ 13.009770] but task is already holding lock:
[ 13.010239] 00000000d663ef86 (bpf_event_mutex){+.+.}, at: bpf_probe_register+0x1d/0x60
[ 13.010877]
[ 13.010877] which lock already depends on the new lock.
[ 13.010877]
[ 13.011532]
[ 13.011532] the existing dependency chain (in reverse order) is:
[ 13.012129]
[ 13.012129] -> #4 (bpf_event_mutex){+.+.}:
[ 13.012582] perf_event_query_prog_array+0x9b/0x130
[ 13.013016] _perf_ioctl+0x3aa/0x830
[ 13.013354] perf_ioctl+0x2e/0x50
[ 13.013668] do_vfs_ioctl+0x8f/0x6a0
[ 13.014003] ksys_ioctl+0x70/0x80
[ 13.014320] __x64_sys_ioctl+0x16/0x20
[ 13.014668] do_syscall_64+0x4a/0x180
[ 13.015007] entry_SYSCALL_64_after_hwframe+0x49/0xbe
[ 13.015469]
[ 13.015469] -> #3 (&cpuctx_mutex){+.+.}:
[ 13.015910] perf_event_init_cpu+0x5a/0x90
[ 13.016291] perf_event_init+0x1b2/0x1de
[ 13.016654] start_kernel+0x2b8/0x42a
[ 13.016995] secondary_startup_64+0xa4/0xb0
[ 13.017382]
[ 13.017382] -> #2 (pmus_lock){+.+.}:
[ 13.017794] perf_event_init_cpu+0x21/0x90
[ 13.018172] cpuhp_invoke_callback+0xb3/0x960
[ 13.018573] _cpu_up+0xa7/0x140
[ 13.018871] do_cpu_up+0xa4/0xc0
[ 13.019178] smp_init+0xcd/0xd2
[ 13.019483] kernel_init_freeable+0x123/0x24f
[ 13.019878] kernel_init+0xa/0x110
[ 13.020201] ret_from_fork+0x24/0x30
[ 13.020541]
[ 13.020541] -> #1 (cpu_hotplug_lock.rw_sem){++++}:
[ 13.021051] static_key_slow_inc+0xe/0x20
[ 13.021424] tracepoint_probe_register_prio+0x28c/0x300
[ 13.021891] perf_trace_event_init+0x11f/0x250
[ 13.022297] perf_trace_init+0x6b/0xa0
[ 13.022644] perf_tp_event_init+0x25/0x40
[ 13.023011] perf_try_init_event+0x6b/0x90
[ 13.023386] perf_event_alloc+0x9a8/0xc40
[ 13.023754] __do_sys_perf_event_open+0x1dd/0xd30
[ 13.024173] do_syscall_64+0x4a/0x180
[ 13.024519] entry_SYSCALL_64_after_hwframe+0x49/0xbe
[ 13.024968]
[ 13.024968] -> #0 (tracepoints_mutex){+.+.}:
[ 13.025434] __mutex_lock+0x86/0x970
[ 13.025764] tracepoint_probe_register_prio+0x2d/0x300
[ 13.026215] bpf_probe_register+0x40/0x60
[ 13.026584] bpf_raw_tracepoint_open.isra.34+0xa4/0x130
[ 13.027042] __do_sys_bpf+0x94f/0x1a90
[ 13.027389] do_syscall_64+0x4a/0x180
[ 13.027727] entry_SYSCALL_64_after_hwframe+0x49/0xbe
[ 13.028171]
[ 13.028171] other info that might help us debug this:
[ 13.028171]
[ 13.028807] Chain exists of:
[ 13.028807] tracepoints_mutex --> &cpuctx_mutex --> bpf_event_mutex
[ 13.028807]
[ 13.029666] Possible unsafe locking scenario:
[ 13.029666]
[ 13.030140] CPU0 CPU1
[ 13.030510] ---- ----
[ 13.030875] lock(bpf_event_mutex);
[ 13.031166] lock(&cpuctx_mutex);
[ 13.031645] lock(bpf_event_mutex);
[ 13.032135] lock(tracepoints_mutex);
[ 13.032441]
[ 13.032441] *** DEADLOCK ***
[ 13.032441]
[ 13.032911] 1 lock held by test_progs/246:
[ 13.033239] #0: 00000000d663ef86 (bpf_event_mutex){+.+.}, at: bpf_probe_register+0x1d/0x60
[ 13.033909]
[ 13.033909] stack backtrace:
[ 13.034258] CPU: 1 PID: 246 Comm: test_progs Not tainted 5.0.0-rc3-00018-g2fa53f892422-dirty #477
[ 13.034964] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.11.0-2.el7 04/01/2014
[ 13.035657] Call Trace:
[ 13.035859] dump_stack+0x5f/0x8b
[ 13.036130] print_circular_bug.isra.37+0x1ce/0x1db
[ 13.036526] __lock_acquire+0x1158/0x1350
[ 13.036852] ? lock_acquire+0x98/0x190
[ 13.037154] lock_acquire+0x98/0x190
[ 13.037447] ? tracepoint_probe_register_prio+0x2d/0x300
[ 13.037876] __mutex_lock+0x86/0x970
[ 13.038167] ? tracepoint_probe_register_prio+0x2d/0x300
[ 13.038600] ? tracepoint_probe_register_prio+0x2d/0x300
[ 13.039028] ? __mutex_lock+0x86/0x970
[ 13.039337] ? __mutex_lock+0x24a/0x970
[ 13.039649] ? bpf_probe_register+0x1d/0x60
[ 13.039992] ? __bpf_trace_sched_wake_idle_without_ipi+0x10/0x10
[ 13.040478] ? tracepoint_probe_register_prio+0x2d/0x300
[ 13.040906] tracepoint_probe_register_prio+0x2d/0x300
[ 13.041325] bpf_probe_register+0x40/0x60
[ 13.041649] bpf_raw_tracepoint_open.isra.34+0xa4/0x130
[ 13.042068] ? __might_fault+0x3e/0x90
[ 13.042374] __do_sys_bpf+0x94f/0x1a90
[ 13.042678] do_syscall_64+0x4a/0x180
[ 13.042975] entry_SYSCALL_64_after_hwframe+0x49/0xbe
[ 13.043382] RIP: 0033:0x7f23b10a07f9
[ 13.045155] RSP: 002b:00007ffdef42fdd8 EFLAGS: 00000202 ORIG_RAX: 0000000000000141
[ 13.045759] RAX: ffffffffffffffda RBX: 00007ffdef42ff70 RCX: 00007f23b10a07f9
[ 13.046326] RDX: 0000000000000070 RSI: 00007ffdef42fe10 RDI: 0000000000000011
[ 13.046893] RBP: 00007ffdef42fdf0 R08: 0000000000000038 R09: 00007ffdef42fe10
[ 13.047462] R10: 0000000000000000 R11: 0000000000000202 R12: 0000000000000000
[ 13.048029] R13: 0000000000000016 R14: 00007f23b1db4690 R15: 0000000000000000
Since tracepoints_mutex will be taken in tracepoint_probe_register/unregister()
there is no need to take bpf_event_mutex too.
bpf_event_mutex is protecting modifications to prog array used in kprobe/perf bpf progs.
bpf_raw_tracepoints don't need to take this mutex.
Fixes: c4f6699dfcb8 ("bpf: introduce BPF_RAW_TRACEPOINT")
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit a89fac57b5d080771efd4d71feaae19877cf68f0 ]
Lockdep warns about false positive:
[ 12.492084] 00000000e6b28347 (&head->lock){+...}, at: pcpu_freelist_push+0x2a/0x40
[ 12.492696] but this lock was taken by another, HARDIRQ-safe lock in the past:
[ 12.493275] (&rq->lock){-.-.}
[ 12.493276]
[ 12.493276]
[ 12.493276] and interrupts could create inverse lock ordering between them.
[ 12.493276]
[ 12.494435]
[ 12.494435] other info that might help us debug this:
[ 12.494979] Possible interrupt unsafe locking scenario:
[ 12.494979]
[ 12.495518] CPU0 CPU1
[ 12.495879] ---- ----
[ 12.496243] lock(&head->lock);
[ 12.496502] local_irq_disable();
[ 12.496969] lock(&rq->lock);
[ 12.497431] lock(&head->lock);
[ 12.497890] <Interrupt>
[ 12.498104] lock(&rq->lock);
[ 12.498368]
[ 12.498368] *** DEADLOCK ***
[ 12.498368]
[ 12.498837] 1 lock held by dd/276:
[ 12.499110] #0: 00000000c58cb2ee (rcu_read_lock){....}, at: trace_call_bpf+0x5e/0x240
[ 12.499747]
[ 12.499747] the shortest dependencies between 2nd lock and 1st lock:
[ 12.500389] -> (&rq->lock){-.-.} {
[ 12.500669] IN-HARDIRQ-W at:
[ 12.500934] _raw_spin_lock+0x2f/0x40
[ 12.501373] scheduler_tick+0x4c/0xf0
[ 12.501812] update_process_times+0x40/0x50
[ 12.502294] tick_periodic+0x27/0xb0
[ 12.502723] tick_handle_periodic+0x1f/0x60
[ 12.503203] timer_interrupt+0x11/0x20
[ 12.503651] __handle_irq_event_percpu+0x43/0x2c0
[ 12.504167] handle_irq_event_percpu+0x20/0x50
[ 12.504674] handle_irq_event+0x37/0x60
[ 12.505139] handle_level_irq+0xa7/0x120
[ 12.505601] handle_irq+0xa1/0x150
[ 12.506018] do_IRQ+0x77/0x140
[ 12.506411] ret_from_intr+0x0/0x1d
[ 12.506834] _raw_spin_unlock_irqrestore+0x53/0x60
[ 12.507362] __setup_irq+0x481/0x730
[ 12.507789] setup_irq+0x49/0x80
[ 12.508195] hpet_time_init+0x21/0x32
[ 12.508644] x86_late_time_init+0xb/0x16
[ 12.509106] start_kernel+0x390/0x42a
[ 12.509554] secondary_startup_64+0xa4/0xb0
[ 12.510034] IN-SOFTIRQ-W at:
[ 12.510305] _raw_spin_lock+0x2f/0x40
[ 12.510772] try_to_wake_up+0x1c7/0x4e0
[ 12.511220] swake_up_locked+0x20/0x40
[ 12.511657] swake_up_one+0x1a/0x30
[ 12.512070] rcu_process_callbacks+0xc5/0x650
[ 12.512553] __do_softirq+0xe6/0x47b
[ 12.512978] irq_exit+0xc3/0xd0
[ 12.513372] smp_apic_timer_interrupt+0xa9/0x250
[ 12.513876] apic_timer_interrupt+0xf/0x20
[ 12.514343] default_idle+0x1c/0x170
[ 12.514765] do_idle+0x199/0x240
[ 12.515159] cpu_startup_entry+0x19/0x20
[ 12.515614] start_kernel+0x422/0x42a
[ 12.516045] secondary_startup_64+0xa4/0xb0
[ 12.516521] INITIAL USE at:
[ 12.516774] _raw_spin_lock_irqsave+0x38/0x50
[ 12.517258] rq_attach_root+0x16/0xd0
[ 12.517685] sched_init+0x2f2/0x3eb
[ 12.518096] start_kernel+0x1fb/0x42a
[ 12.518525] secondary_startup_64+0xa4/0xb0
[ 12.518986] }
[ 12.519132] ... key at: [<ffffffff82b7bc28>] __key.71384+0x0/0x8
[ 12.519649] ... acquired at:
[ 12.519892] pcpu_freelist_pop+0x7b/0xd0
[ 12.520221] bpf_get_stackid+0x1d2/0x4d0
[ 12.520563] ___bpf_prog_run+0x8b4/0x11a0
[ 12.520887]
[ 12.521008] -> (&head->lock){+...} {
[ 12.521292] HARDIRQ-ON-W at:
[ 12.521539] _raw_spin_lock+0x2f/0x40
[ 12.521950] pcpu_freelist_push+0x2a/0x40
[ 12.522396] bpf_get_stackid+0x494/0x4d0
[ 12.522828] ___bpf_prog_run+0x8b4/0x11a0
[ 12.523296] INITIAL USE at:
[ 12.523537] _raw_spin_lock+0x2f/0x40
[ 12.523944] pcpu_freelist_populate+0xc0/0x120
[ 12.524417] htab_map_alloc+0x405/0x500
[ 12.524835] __do_sys_bpf+0x1a3/0x1a90
[ 12.525253] do_syscall_64+0x4a/0x180
[ 12.525659] entry_SYSCALL_64_after_hwframe+0x49/0xbe
[ 12.526167] }
[ 12.526311] ... key at: [<ffffffff838f7668>] __key.13130+0x0/0x8
[ 12.526812] ... acquired at:
[ 12.527047] __lock_acquire+0x521/0x1350
[ 12.527371] lock_acquire+0x98/0x190
[ 12.527680] _raw_spin_lock+0x2f/0x40
[ 12.527994] pcpu_freelist_push+0x2a/0x40
[ 12.528325] bpf_get_stackid+0x494/0x4d0
[ 12.528645] ___bpf_prog_run+0x8b4/0x11a0
[ 12.528970]
[ 12.529092]
[ 12.529092] stack backtrace:
[ 12.529444] CPU: 0 PID: 276 Comm: dd Not tainted 5.0.0-rc3-00018-g2fa53f892422 #475
[ 12.530043] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.11.0-2.el7 04/01/2014
[ 12.530750] Call Trace:
[ 12.530948] dump_stack+0x5f/0x8b
[ 12.531248] check_usage_backwards+0x10c/0x120
[ 12.531598] ? ___bpf_prog_run+0x8b4/0x11a0
[ 12.531935] ? mark_lock+0x382/0x560
[ 12.532229] mark_lock+0x382/0x560
[ 12.532496] ? print_shortest_lock_dependencies+0x180/0x180
[ 12.532928] __lock_acquire+0x521/0x1350
[ 12.533271] ? find_get_entry+0x17f/0x2e0
[ 12.533586] ? find_get_entry+0x19c/0x2e0
[ 12.533902] ? lock_acquire+0x98/0x190
[ 12.534196] lock_acquire+0x98/0x190
[ 12.534482] ? pcpu_freelist_push+0x2a/0x40
[ 12.534810] _raw_spin_lock+0x2f/0x40
[ 12.535099] ? pcpu_freelist_push+0x2a/0x40
[ 12.535432] pcpu_freelist_push+0x2a/0x40
[ 12.535750] bpf_get_stackid+0x494/0x4d0
[ 12.536062] ___bpf_prog_run+0x8b4/0x11a0
It has been explained that is a false positive here:
https://lkml.org/lkml/2018/7/25/756
Recap:
- stackmap uses pcpu_freelist
- The lock in pcpu_freelist is a percpu lock
- stackmap is only used by tracing bpf_prog
- A tracing bpf_prog cannot be run if another bpf_prog
has already been running (ensured by the percpu bpf_prog_active counter).
Eric pointed out that this lockdep splats stops other
legit lockdep splats in selftests/bpf/test_progs.c.
Fix this by calling local_irq_save/restore for stackmap.
Another false positive had also been worked around by calling
local_irq_save in commit 89ad2fa3f043 ("bpf: fix lockdep splat").
That commit added unnecessary irq_save/restore to fast path of
bpf hash map. irqs are already disabled at that point, since htab
is holding per bucket spin_lock with irqsave.
Let's reduce overhead for htab by introducing __pcpu_freelist_push/pop
function w/o irqsave and convert pcpu_freelist_push/pop to irqsave
to be used elsewhere (right now only in stackmap).
It stops lockdep false positive in stackmap with a bit of acceptable overhead.
Fixes: 557c0c6e7df8 ("bpf: convert stackmap to pre-allocation")
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 1bb54c4071f585ebef56ce8fdfe6026fa2cbcddd ]
Previously, bpf_num_possible_cpus() had a bug when calculating a
number of possible CPUs in the case of sparse CPU allocations, as
it was considering only the first range or element of
/sys/devices/system/cpu/possible.
E.g. in the case of "0,2-3" (CPU 1 is not available), the function
returned 1 instead of 3.
This patch fixes the function by making it parse all CPU ranges and
elements.
Signed-off-by: Martynas Pumputis <m@lambda.lt>
Acked-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2c1cf00eeacb784781cf1c9896b8af001246d339 ]
If create_buf_file() returns an error, don't try to reference it later
as a valid dentry pointer.
This problem was exposed when debugfs started to return errors instead
of just NULL for some calls when they do not succeed properly.
Also, the check for WARN_ON(dentry) was just wrong :)
Reported-by: Kees Cook <keescook@chromium.org>
Reported-and-tested-by: syzbot+16c3a70e1e9b29346c43@syzkaller.appspotmail.com
Reported-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: David Rientjes <rientjes@google.com>
Fixes: ff9fb72bc077 ("debugfs: return error values, not NULL")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 56841070ccc87b463ac037d2d1f2beb8e5e35f0c ]
According to ARM IHI 0069C (ID070116), we should use GITS_TYPER's
bits [7:4] as ITT_entry_size instead of [8:4]. Although this is
pretty annoying, it only results in a potential over-allocation
of memory, and nothing bad happens.
Fixes: 3dfa576bfb45 ("irqchip/gic-v3-its: Add probing for VLPI properties")
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
[maz: massaged subject and commit message]
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e2cd682deb231ba6f80524bb84e57e7138261149 ]
In stmmac xmit callback we use a different flow for TSO packets but TSO
xmit callback is not disabling the EEE mode.
Fix this by disabling earlier the EEE mode, i.e. before calling the TSO
xmit callback.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c5acdbee22a1b200dde07effd26fd1f649e9ab8a ]
The number of TSO enabled channels in HW can be different than the
number of total channels. There is no way to determined, at runtime, the
number of TSO capable channels and its safe to assume that if TSO is
enabled then at least channel 0 will be TSO capable.
Lets always send TSO packets from Queue 0.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4ec5302fa906ec9d86597b236f62315bacdb9622 ]
If we don't have DT then stmmac_clk will not be available. Let's add a
new Platform Data field so that we can specify the refclk by this mean.
This way we can still use the coalesce command in PCI based setups.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6e11ea9de9576a644045ffdc2067c09bc2012eda ]
amdgpu only uses shared-fences internally, but dmabuf importers rely on
implicit write hazard tracking via the reservation_object.fence_excl.
For example, the importer use the write hazard for timing a page flip to
only occur after the exporter has finished flushing its write into the
surface. As such, on exporting a dmabuf, we must either flush all
outstanding fences (for we do not know which are writes and should have
been exclusive) or alternatively create a new exclusive fence that is
the composite of all the existing shared fences, and so will only be
signaled when all earlier fences are signaled (ensuring that we can not
be signaled before the completion of any earlier write).
v2: reservation_object is already locked by amdgpu_bo_reserve()
v3: Replace looping with get_fences_rcu and special case the promotion
of a single shared fence directly to an exclusive fence, bypassing the
fence array.
v4: Drop the fence array ref after assigning to reservation_object
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=107341
Testcase: igt/amd_prime/amd-to-i915
References: 8e94a46c1770 ("drm/amdgpu: Attach exclusive fence to prime exported bo's. (v5)")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Reviewed-by: "Christian König" <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit afeff4c16edaa6275b903f82b0561406259aa3a3 ]
Check if the device is root rather before attempting to see what
speeds the pcie port supports. Fixes a crash with pci passthrough
in a VM.
Bug: https://bugs.freedesktop.org/show_bug.cgi?id=109366
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit dc14eb12f6bb3e779c5461429c1889a339c67aab ]
Add missing power_average to visible check for power
attributes for APUs. Was missed before.
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2380a22b60ce6f995eac806e69c66e397b59d045 ]
Resetting bit 4 disables the interrupt delivery to the "secure
processor" core. This breaks the keyboard on a OLPC XO 1.75 laptop,
where the firmware running on the "secure processor" bit-bangs the
PS/2 protocol over the GPIO lines.
It is not clear what the rest of the bits are and Marvell was unhelpful
when asked for documentation. Aside from the SP bit, there are probably
priority bits.
Leaving the unknown bits as the firmware set them up seems to be a wiser
course of action compared to just turning them off.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Pavel Machek <pavel@ucw.cz>
[maz: fixed-up subject and commit message]
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 45725e0fc3e7fe52fedb94f59806ec50e9618682 ]
In the unlikely event that we cannot find any available LPI in the
system, we should gracefully return an error instead of carrying
on with no LPI allocated at all.
Fixes: 38dd7c494cf6 ("irqchip/gic-v3-its: Drop chunk allocation compatibility")
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
Marek Szyprowski
Alistair Strachan
Jan Kiszka
Alexander Shishkin
Gustavo A. R. Silva
Vincent Batts
Jason Gerecke
Keith Busch
Liu Bo
Sudarsana Reddy Kalluru
Manish Chopra
Tetsuo Handa
Philip Yang
Tony Lindgren
Ross Lagerwall
Jun-Ru Chang
Arnaldo Carvalho de Melo
Jiri Olsa
Julian Wiedmann
Martynas Pumputis
Florian Westphal
Naresh Kamboju
Andy Shevchenko
Stefano Garzarella
Codrin Ciubotariu
Paul Kocialkowski
Martin KaFai Lau
Alexei Starovoitov
Martynas Pumputis
Greg Kroah-Hartman
Zenghui Yu
Jose Abreu
Chris Wilson
Alex Deucher
Lubomir Rintel
Marc Zyngier