| Age | Commit message (Collapse) | Author |
|---|
|
simultaneous mode
commit 8bef455c8b1694547ee59e8b1939205ed9d901a6 upstream.
The XADC has two internal ADCs. Depending on the mode it is operating in
either one or both of them are used. The device manual calls this
continuous (one ADC) and simultaneous (both ADCs) mode.
The meaning of the sequencing register for the aux channels changes
depending on the mode.
In continuous mode each bit corresponds to one of the 16 aux channels. And
the single ADC will convert them one by one in order.
In simultaneous mode the aux channels are split into two groups the first 8
channels are assigned to the first ADC and the other 8 channels to the
second ADC. The upper 8 bits of the sequencing register are unused and the
lower 8 bits control both ADCs. This means a bit needs to be set if either
the corresponding channel from the first group or the second group (or
both) are set.
Currently the driver does not have the special handling required for
simultaneous mode. Add it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Fixes: bdc8cda1d010 ("iio:adc: Add Xilinx XADC driver")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f954b098fbac4d183219ce5b42d76d6df2aed50a upstream.
When enabling the trigger and unmasking the end-of-sequence (EOS) interrupt
the EOS interrupt should be cleared from the status register. Otherwise it
is possible that it was still set from a previous capture. If that is the
case the interrupt would fire immediately even though no conversion has
been done yet and stale data is being read from the device.
The old code only clears the interrupt if the interrupt was previously
unmasked. Which does not make much sense since the interrupt is always
masked at this point and in addition masking the interrupt does not clear
the interrupt from the status register. So the clearing needs to be done
unconditionally.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Fixes: bdc8cda1d010 ("iio:adc: Add Xilinx XADC driver")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e44ec7794d88f918805d700240211a9ec05ed89d upstream.
The check for shutting down the second ADC is inverted. This causes it to
be powered down when it should be enabled. As a result channels that are
supposed to be handled by the second ADC return invalid conversion results.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Fixes: bdc8cda1d010 ("iio:adc: Add Xilinx XADC driver")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e2042d2936dfc84e9c600fe9b9d0039ca0e54b7d upstream.
This commit fixes the following error:
"BUG: sleeping function called from invalid context at kernel/irq/chip.c"
In DMA mode suppress the trigger irq handler, and make the buffer
transfers directly in DMA callback, instead.
Fixes: 2763ea0585c9 ("iio: adc: stm32: add optional dma support")
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Acked-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e450e07c14abae563ad13b064cbce9fdccc6bc8d upstream.
Indeed, relying on addr being not 0 cannot work because some device have
their register to set odr at address 0. As a matter of fact, if the odr
can be set, then there is a mask.
Sensors with ODR register at address 0 are: lsm303dlh, lsm303dlhc, lsm303dlm
Fixes: 7d245172675a ("iio: common: st_sensors: check odr address value in st_sensors_set_odr()")
Signed-off-by: Lary Gibaud <yarl-baudig@mailoo.org>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a07479147be03d2450376ebaff9ea1a0682f25d6 upstream.
This change removes the semi-colon from the devm_iio_device_register()
macro which seems to have been added by accident.
Fixes: 63b19547cc3d9 ("iio: Use macro magic to avoid manual assign of driver_module")
Signed-off-by: Lars Engebretsen <lars@engebretsen.ch>
Cc: <Stable@vger.kernel.org>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit fef66ae73a611e84c8b4b74ff6f805ec5f113477 ]
It turned out that ALC1220-VB USB-audio device gives the interrupt
event to some PCM terminals while those don't allow the connector
state request but only the actual I/O terminals return the request.
The recent commit 7dc3c5a0172e ("ALSA: usb-audio: Don't create jack
controls for PCM terminals") excluded those phantom terminals, so
those events are ignored, too.
My first thought was that this could be easily deduced from the
associated terminals, but some of them have even no associate terminal
ID, hence it's not too trivial to figure out.
Since the number of such terminals are small and limited, this patch
implements another quirk table for the simple mapping of the
connectors. It's not really scalable, but let's hope that there will
be not many such funky devices in future.
Fixes: 7dc3c5a0172e ("ALSA: usb-audio: Don't create jack controls for PCM terminals")
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=206873
Link: https://lore.kernel.org/r/20200422113320.26664-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit a43c1c41bc5145971d06edc42a6b1e8faa0e2bc3 ]
TRX40 mobos from MSI and others with ALC1220-VB USB-audio device need
yet more quirks for the proper control names.
This patch provides the mapping table for those boards, correcting the
FU names for volume and mute controls as well as the terminal names
for jack controls. It also improves build_connector_control() not to
add the directional suffix blindly if the string is given from the
mapping table.
With this patch applied, the new UCM profiles will be effective.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=206873
Link: https://lore.kernel.org/r/20200420062036.28567-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit a8cf44f085ac12c0b5b8750ebb3b436c7f455419 ]
The commit 3c6fd1f07ed0 ("ALSA: hda: Add driver blacklist") added a
new blacklist for the devices that are known to have empty codecs, and
one of the entries was ASUS ROG Zenith II (PCI SSID 1043:874f).
However, it turned out that the very same PCI SSID is used for the
previous model that does have the valid HD-audio codecs and the change
broke the sound on it.
This patch reverts the corresponding entry as a temporary solution.
Although Zenith II and co will see get the empty HD-audio bus again,
it'd be merely resource wastes and won't affect the functionality,
so it's no end of the world. We'll need to address this later,
e.g. by either switching to DMI string matching or using PCI ID &
SSID pairs.
Fixes: 3c6fd1f07ed0 ("ALSA: hda: Add driver blacklist")
Reported-by: Johnathan Smithinovic <johnathan.smithinovic@gmx.at>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200419071926.22683-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4f0882491a148059a52480e753b7f07fc550e188 ]
By allocating a kernel buffer with a user-supplied buffer length, it
is possible that a false positive ENOMEM error may be returned because
the user-supplied length is just too large even if the system do have
enough memory to hold the actual key data.
Moreover, if the buffer length is larger than the maximum amount of
memory that can be returned by kmalloc() (2^(MAX_ORDER-1) number of
pages), a warning message will also be printed.
To reduce this possibility, we set a threshold (PAGE_SIZE) over which we
do check the actual key length first before allocating a buffer of the
right size to hold it. The threshold is arbitrary, it is just used to
trigger a buffer length check. It does not limit the actual key length
as long as there is enough memory to satisfy the memory request.
To further avoid large buffer allocation failure due to page
fragmentation, kvmalloc() is used to allocate the buffer so that vmapped
pages can be used when there is not a large enough contiguous set of
pages available for allocation.
In the extremely unlikely scenario that the key keeps on being changed
and made longer (still <= buflen) in between 2 __keyctl_read_key()
calls, the __keyctl_read_key() calling loop in keyctl_read_key() may
have to be iterated a large number of times, but definitely not infinite.
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c391eb8366ae052d571bb2841f1ccb4d39f3ceb8 ]
The mlxsw_sp_acl_rulei_create() function is supposed to return an error
pointer from mlxsw_afa_block_create(). The problem is that these
functions both return NULL instead of error pointers. Half the callers
expect NULL and half expect error pointers so it could lead to a NULL
dereference on failure.
This patch changes both of them to return error pointers and changes all
the callers which checked for NULL to check for IS_ERR() instead.
Fixes: 4cda7d8d7098 ("mlxsw: core: Introduce flexible actions support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 16b9db1ce34ff00d6c18e82825125cfef0cdfb13 ]
To avoid a loop with qdiscs and xfrms, check if the skb has already gone
through the qdisc attached to the VRF device and then to the xfrm layer.
If so, no need for a second redirect.
Fixes: 193125dbd8eb ("net: Introduce VRF device driver")
Reported-by: Trev Larock <trev@larock.ca>
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 0c922a4850eba2e668f73a3f1153196e09abb251 ]
IPSKB_XFRM_TRANSFORMED and IP6SKB_XFRM_TRANSFORMED are skb flags set by
xfrm code to tell other skb handlers that the packet has been passed
through the xfrm output functions. Simplify the code and just always
set them rather than conditionally based on netfilter enabled thus
making the flag available for other users.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 64fec9493f7dc9bdd7233bcfe98985c45bd0e3c1 ]
Flip the IVL_SVL_SELECT bit correctly based on the VLAN enable status,
the default is to perform Shared VLAN learning instead of Individual
learning.
Fixes: 1da6df85c6fb ("net: dsa: b53: Implement ARL add/del/dump operations")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 6344dbde6a27d10d16246d734b968f84887841e2 ]
When asking the ARL to read a MAC address, we will get a number of bins
returned in a single read. Out of those bins, there can essentially be 3
states:
- all bins are full, we have no space left, and we can either replace an
existing address or return that full condition
- the MAC address was found, then we need to return its bin index and
modify that one, and only that one
- the MAC address was not found and we have a least one bin free, we use
that bin index location then
The code would unfortunately fail on all counts.
Fixes: 1da6df85c6fb ("net: dsa: b53: Implement ARL add/del/dump operations")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit c2e77a18a7ed65eb48f6e389b6a59a0fd753646a ]
The ARL {MAC,VID} tuple and the forward entry were off by 0x10 bytes,
which means that when we read/wrote from/to ARL bin index 0, we were
actually accessing the ARLA_RWCTRL register.
Fixes: 1da6df85c6fb ("net: dsa: b53: Implement ARL add/del/dump operations")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 2e97b0cd1651a270f3a3fcf42115c51f3284c049 ]
When VLAN is enabled, and an ARL search is issued, we also need to
compare the full {MAC,VID} tuple before returning a successful search
result.
Fixes: 1da6df85c6fb ("net: dsa: b53: Implement ARL add/del/dump operations")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit a53c102872ad6e34e1518e25899dc9498c27f8b1 ]
When a qdisc is attached to the VRF device, the packet goes down the ndo
xmit function which is setup to send the packet back to the VRF driver
which does a lookup to send the packet out. The lookup in the VRF driver
is not considering xfrm policies. Change it to use ip6_dst_lookup_flow
rather than ip6_route_output.
Fixes: 35402e313663 ("net: Add IPv6 support to VRF device")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 1c30fbc76b8f0c07c92a8ca4cd7c456612e17eb5 ]
When team mode is changed or set, the team_mode_get() is called to check
whether the mode module is inserted or not. If the mode module is not
inserted, it calls the request_module().
In the request_module(), it creates a child process, which is
the "modprobe" process and waits for the done of the child process.
At this point, the following locks were used.
down_read(&cb_lock()); by genl_rcv()
genl_lock(); by genl_rcv_msc()
rtnl_lock(); by team_nl_cmd_options_set()
mutex_lock(&team->lock); by team_nl_team_get()
Concurrently, the team module could be removed by rmmod or "modprobe -r"
The __exit function of team module is team_module_exit(), which calls
team_nl_fini() and it tries to acquire following locks.
down_write(&cb_lock);
genl_lock();
Because of the genl_lock() and cb_lock, this process can't be finished
earlier than request_module() routine.
The problem secenario.
CPU0 CPU1
team_mode_get
request_module()
modprobe -r team_mode_roundrobin
team <--(B)
modprobe team <--(A)
team_mode_roundrobin
By request_module(), the "modprobe team_mode_roundrobin" command
will be executed. At this point, the modprobe process will decide
that the team module should be inserted before team_mode_roundrobin.
Because the team module is being removed.
By the module infrastructure, the same module insert/remove operations
can't be executed concurrently.
So, (A) waits for (B) but (B) also waits for (A) because of locks.
So that the hang occurs at this point.
Test commands:
while :
do
teamd -d &
killall teamd &
modprobe -rv team_mode_roundrobin &
done
The approach of this patch is to hold the reference count of the team
module if the team module is compiled as a module. If the reference count
of the team module is not zero while request_module() is being called,
the team module will not be removed at that moment.
So that the above scenario could not occur.
Fixes: 3d249d4ca7d0 ("net: introduce ethernet teaming device")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 9bacd256f1354883d3c1402655153367982bba49 ]
TCP stack is dumb in how it cooks its output packets.
Depending on MAX_HEADER value, we might chose a bad ending point
for the headers.
If we align the end of TCP headers to cache line boundary, we
make sure to always use the smallest number of cache lines,
which always help.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit a1211bf9a7774706722ba3b18c6157d980319f79 ]
skb->sk does not always point to a full blown socket,
we need to use sk_fullsock() before accessing fields which
only make sense on full socket.
BUG: KASAN: use-after-free in report_sock_error+0x286/0x300 net/sched/sch_etf.c:141
Read of size 1 at addr ffff88805eb9b245 by task syz-executor.5/9630
CPU: 1 PID: 9630 Comm: syz-executor.5 Not tainted 5.7.0-rc2-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
<IRQ>
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x188/0x20d lib/dump_stack.c:118
print_address_description.constprop.0.cold+0xd3/0x315 mm/kasan/report.c:382
__kasan_report.cold+0x35/0x4d mm/kasan/report.c:511
kasan_report+0x33/0x50 mm/kasan/common.c:625
report_sock_error+0x286/0x300 net/sched/sch_etf.c:141
etf_enqueue_timesortedlist+0x389/0x740 net/sched/sch_etf.c:170
__dev_xmit_skb net/core/dev.c:3710 [inline]
__dev_queue_xmit+0x154a/0x30a0 net/core/dev.c:4021
neigh_hh_output include/net/neighbour.h:499 [inline]
neigh_output include/net/neighbour.h:508 [inline]
ip6_finish_output2+0xfb5/0x25b0 net/ipv6/ip6_output.c:117
__ip6_finish_output+0x442/0xab0 net/ipv6/ip6_output.c:143
ip6_finish_output+0x34/0x1f0 net/ipv6/ip6_output.c:153
NF_HOOK_COND include/linux/netfilter.h:296 [inline]
ip6_output+0x239/0x810 net/ipv6/ip6_output.c:176
dst_output include/net/dst.h:435 [inline]
NF_HOOK include/linux/netfilter.h:307 [inline]
NF_HOOK include/linux/netfilter.h:301 [inline]
ip6_xmit+0xe1a/0x2090 net/ipv6/ip6_output.c:280
tcp_v6_send_synack+0x4e7/0x960 net/ipv6/tcp_ipv6.c:521
tcp_rtx_synack+0x10d/0x1a0 net/ipv4/tcp_output.c:3916
inet_rtx_syn_ack net/ipv4/inet_connection_sock.c:669 [inline]
reqsk_timer_handler+0x4c2/0xb40 net/ipv4/inet_connection_sock.c:763
call_timer_fn+0x1ac/0x780 kernel/time/timer.c:1405
expire_timers kernel/time/timer.c:1450 [inline]
__run_timers kernel/time/timer.c:1774 [inline]
__run_timers kernel/time/timer.c:1741 [inline]
run_timer_softirq+0x623/0x1600 kernel/time/timer.c:1787
__do_softirq+0x26c/0x9f7 kernel/softirq.c:292
invoke_softirq kernel/softirq.c:373 [inline]
irq_exit+0x192/0x1d0 kernel/softirq.c:413
exiting_irq arch/x86/include/asm/apic.h:546 [inline]
smp_apic_timer_interrupt+0x19e/0x600 arch/x86/kernel/apic/apic.c:1140
apic_timer_interrupt+0xf/0x20 arch/x86/entry/entry_64.S:829
</IRQ>
RIP: 0010:des_encrypt+0x157/0x9c0 lib/crypto/des.c:792
Code: 85 22 06 00 00 41 31 dc 41 8b 4d 04 44 89 e2 41 83 e4 3f 4a 8d 3c a5 60 72 72 88 81 e2 3f 3f 3f 3f 48 89 f8 48 c1 e8 03 31 d9 <0f> b6 34 28 48 89 f8 c1 c9 04 83 e0 07 83 c0 03 40 38 f0 7c 09 40
RSP: 0018:ffffc90003b5f6c0 EFLAGS: 00000282 ORIG_RAX: ffffffffffffff13
RAX: 1ffffffff10e4e55 RBX: 00000000d2f846d0 RCX: 00000000d2f846d0
RDX: 0000000012380612 RSI: ffffffff839863ca RDI: ffffffff887272a8
RBP: dffffc0000000000 R08: ffff888091d0a380 R09: 0000000000800081
R10: 0000000000000000 R11: 0000000000000000 R12: 0000000000000012
R13: ffff8880a8ae8078 R14: 00000000c545c93e R15: 0000000000000006
cipher_crypt_one crypto/cipher.c:75 [inline]
crypto_cipher_encrypt_one+0x124/0x210 crypto/cipher.c:82
crypto_cbcmac_digest_update+0x1b5/0x250 crypto/ccm.c:830
crypto_shash_update+0xc4/0x120 crypto/shash.c:119
shash_ahash_update+0xa3/0x110 crypto/shash.c:246
crypto_ahash_update include/crypto/hash.h:547 [inline]
hash_sendmsg+0x518/0xad0 crypto/algif_hash.c:102
sock_sendmsg_nosec net/socket.c:652 [inline]
sock_sendmsg+0xcf/0x120 net/socket.c:672
____sys_sendmsg+0x308/0x7e0 net/socket.c:2362
___sys_sendmsg+0x100/0x170 net/socket.c:2416
__sys_sendmmsg+0x195/0x480 net/socket.c:2506
__do_sys_sendmmsg net/socket.c:2535 [inline]
__se_sys_sendmmsg net/socket.c:2532 [inline]
__x64_sys_sendmmsg+0x99/0x100 net/socket.c:2532
do_syscall_64+0xf6/0x7d0 arch/x86/entry/common.c:295
entry_SYSCALL_64_after_hwframe+0x49/0xb3
RIP: 0033:0x45c829
Code: 0d b7 fb ff c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 db b6 fb ff c3 66 2e 0f 1f 84 00 00 00 00
RSP: 002b:00007f6d9528ec78 EFLAGS: 00000246 ORIG_RAX: 0000000000000133
RAX: ffffffffffffffda RBX: 00000000004fc080 RCX: 000000000045c829
RDX: 0000000000000001 RSI: 0000000020002640 RDI: 0000000000000004
RBP: 000000000078bf00 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 00000000ffffffff
R13: 00000000000008d7 R14: 00000000004cb7aa R15: 00007f6d9528f6d4
Fixes: 4b15c7075352 ("net/sched: Make etf report drops on error_queue")
Fixes: 25db26a91364 ("net/sched: Introduce the ETF Qdisc")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Cc: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Reviewed-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit f35d12971b4d814cdb2f659d76b42f0c545270b6 ]
x25_lapb_receive_frame() invokes x25_get_neigh(), which returns a
reference of the specified x25_neigh object to "nb" with increased
refcnt.
When x25_lapb_receive_frame() returns, local variable "nb" becomes
invalid, so the refcount should be decreased to keep refcount balanced.
The reference counting issue happens in one path of
x25_lapb_receive_frame(). When pskb_may_pull() returns false, the
function forgets to decrease the refcnt increased by x25_get_neigh(),
causing a refcnt leak.
Fix this issue by calling x25_neigh_put() when pskb_may_pull() returns
false.
Fixes: cb101ed2c3c7 ("x25: Handle undersized/fragmented skbs")
Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Signed-off-by: Xin Tan <tanxin.ctf@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit f0212a5ebfa6cd789ab47666b9cc169e6e688732 ]
Running with KASAN on a VIM3L systems leads to the following splat
when probing the Ethernet device:
==================================================================
BUG: KASAN: global-out-of-bounds in _get_maxdiv+0x74/0xd8
Read of size 4 at addr ffffa000090615f4 by task systemd-udevd/139
CPU: 1 PID: 139 Comm: systemd-udevd Tainted: G E 5.7.0-rc1-00101-g8624b7577b9c #781
Hardware name: amlogic w400/w400, BIOS 2020.01-rc5 03/12/2020
Call trace:
dump_backtrace+0x0/0x2a0
show_stack+0x20/0x30
dump_stack+0xec/0x148
print_address_description.isra.12+0x70/0x35c
__kasan_report+0xfc/0x1d4
kasan_report+0x4c/0x68
__asan_load4+0x9c/0xd8
_get_maxdiv+0x74/0xd8
clk_divider_bestdiv+0x74/0x5e0
clk_divider_round_rate+0x80/0x1a8
clk_core_determine_round_nolock.part.9+0x9c/0xd0
clk_core_round_rate_nolock+0xf0/0x108
clk_hw_round_rate+0xac/0xf0
clk_factor_round_rate+0xb8/0xd0
clk_core_determine_round_nolock.part.9+0x9c/0xd0
clk_core_round_rate_nolock+0xf0/0x108
clk_core_round_rate_nolock+0xbc/0x108
clk_core_set_rate_nolock+0xc4/0x2e8
clk_set_rate+0x58/0xe0
meson8b_dwmac_probe+0x588/0x72c [dwmac_meson8b]
platform_drv_probe+0x78/0xd8
really_probe+0x158/0x610
driver_probe_device+0x140/0x1b0
device_driver_attach+0xa4/0xb0
__driver_attach+0xcc/0x1c8
bus_for_each_dev+0xf4/0x168
driver_attach+0x3c/0x50
bus_add_driver+0x238/0x2e8
driver_register+0xc8/0x1e8
__platform_driver_register+0x88/0x98
meson8b_dwmac_driver_init+0x28/0x1000 [dwmac_meson8b]
do_one_initcall+0xa8/0x328
do_init_module+0xe8/0x368
load_module+0x3300/0x36b0
__do_sys_finit_module+0x120/0x1a8
__arm64_sys_finit_module+0x4c/0x60
el0_svc_common.constprop.2+0xe4/0x268
do_el0_svc+0x98/0xa8
el0_svc+0x24/0x68
el0_sync_handler+0x12c/0x318
el0_sync+0x158/0x180
The buggy address belongs to the variable:
div_table.63646+0x34/0xfffffffffffffa40 [dwmac_meson8b]
Memory state around the buggy address:
ffffa00009061480: fa fa fa fa 00 00 00 01 fa fa fa fa 00 00 00 00
ffffa00009061500: 05 fa fa fa fa fa fa fa 00 04 fa fa fa fa fa fa
>ffffa00009061580: 00 03 fa fa fa fa fa fa 00 00 00 00 00 00 fa fa
^
ffffa00009061600: fa fa fa fa 00 01 fa fa fa fa fa fa 01 fa fa fa
ffffa00009061680: fa fa fa fa 00 01 fa fa fa fa fa fa 04 fa fa fa
==================================================================
Digging into this indeed shows that the clock divider array is
lacking a final fence, and that the clock subsystems goes in the
weeds. Oh well.
Let's add the empty structure that indicates the end of the array.
Fixes: bd6f48546b9c ("net: stmmac: dwmac-meson8b: Fix the RGMII TX delay on Meson8b/8m2 SoCs")
Signed-off-by: Marc Zyngier <maz@kernel.org>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit d03f228470a8c0a22b774d1f8d47071e0de4f6dd ]
nr_add_node() invokes nr_neigh_get_dev(), which returns a local
reference of the nr_neigh object to "nr_neigh" with increased refcnt.
When nr_add_node() returns, "nr_neigh" becomes invalid, so the refcount
should be decreased to keep refcount balanced.
The issue happens in one normal path of nr_add_node(), which forgets to
decrease the refcnt increased by nr_neigh_get_dev() and causes a refcnt
leak. It should decrease the refcnt before the function returns like
other normal paths do.
Fix this issue by calling nr_neigh_put() before the nr_add_node()
returns.
Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Signed-off-by: Xin Tan <tanxin.ctf@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit a6d0b83f25073bdf08b8547aeff961a62c6ab229 ]
The change to track net_device_stats per ring to better support SMP
missed updating the rx_dropped member.
The ndo_get_stats method is also needed to combine the results for
ethtool statistics (-S) before filling in the ethtool structure.
Fixes: 37a30b435b92 ("net: bcmgenet: Track per TX/RX rings statistics")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 4dee15b4fd0d61ec6bbd179238191e959d34cf7a ]
In the macvlan_device_event(), the list_first_entry_or_null() is used.
This function could return null pointer if there is no node.
But, the macvlan module doesn't check the null pointer.
So, null-ptr-deref would occur.
bond0
|
+----+-----+
| |
macvlan0 macvlan1
| |
dummy0 dummy1
The problem scenario.
If dummy1 is removed,
1. ->dellink() of dummy1 is called.
2. NETDEV_UNREGISTER of dummy1 notification is sent to macvlan module.
3. ->dellink() of macvlan1 is called.
4. NETDEV_UNREGISTER of macvlan1 notification is sent to bond module.
5. __bond_release_one() is called and it internally calls
dev_set_mac_address().
6. dev_set_mac_address() calls the ->ndo_set_mac_address() of macvlan1,
which is macvlan_set_mac_address().
7. macvlan_set_mac_address() calls the dev_set_mac_address() with dummy1.
8. NETDEV_CHANGEADDR of dummy1 is sent to macvlan module.
9. In the macvlan_device_event(), it calls list_first_entry_or_null().
At this point, dummy1 and macvlan1 were removed.
So, list_first_entry_or_null() will return NULL.
Test commands:
ip netns add nst
ip netns exec nst ip link add bond0 type bond
for i in {0..10}
do
ip netns exec nst ip link add dummy$i type dummy
ip netns exec nst ip link add macvlan$i link dummy$i \
type macvlan mode passthru
ip netns exec nst ip link set macvlan$i master bond0
done
ip netns del nst
Splat looks like:
[ 40.585687][ T146] general protection fault, probably for non-canonical address 0xdffffc0000000000: 0000 [#1] SMP DEI
[ 40.587249][ T146] KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007]
[ 40.588342][ T146] CPU: 1 PID: 146 Comm: kworker/u8:2 Not tainted 5.7.0-rc1+ #532
[ 40.589299][ T146] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[ 40.590469][ T146] Workqueue: netns cleanup_net
[ 40.591045][ T146] RIP: 0010:macvlan_device_event+0x4e2/0x900 [macvlan]
[ 40.591905][ T146] Code: 00 00 00 00 00 fc ff df 80 3c 06 00 0f 85 45 02 00 00 48 89 da 48 b8 00 00 00 00 00 fc ff d2
[ 40.594126][ T146] RSP: 0018:ffff88806116f4a0 EFLAGS: 00010246
[ 40.594783][ T146] RAX: dffffc0000000000 RBX: 0000000000000000 RCX: 0000000000000000
[ 40.595653][ T146] RDX: 0000000000000000 RSI: ffff88806547ddd8 RDI: ffff8880540f1360
[ 40.596495][ T146] RBP: ffff88804011a808 R08: fffffbfff4fb8421 R09: fffffbfff4fb8421
[ 40.597377][ T146] R10: ffffffffa7dc2107 R11: 0000000000000000 R12: 0000000000000008
[ 40.598186][ T146] R13: ffff88804011a000 R14: ffff8880540f1000 R15: 1ffff1100c22de9a
[ 40.599012][ T146] FS: 0000000000000000(0000) GS:ffff888067800000(0000) knlGS:0000000000000000
[ 40.600004][ T146] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 40.600665][ T146] CR2: 00005572d3a807b8 CR3: 000000005fcf4003 CR4: 00000000000606e0
[ 40.601485][ T146] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 40.602461][ T146] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 40.603443][ T146] Call Trace:
[ 40.603871][ T146] ? nf_tables_dump_setelem+0xa0/0xa0 [nf_tables]
[ 40.604587][ T146] ? macvlan_uninit+0x100/0x100 [macvlan]
[ 40.605212][ T146] ? __module_text_address+0x13/0x140
[ 40.605842][ T146] notifier_call_chain+0x90/0x160
[ 40.606477][ T146] dev_set_mac_address+0x28e/0x3f0
[ 40.607117][ T146] ? netdev_notify_peers+0xc0/0xc0
[ 40.607762][ T146] ? __module_text_address+0x13/0x140
[ 40.608440][ T146] ? notifier_call_chain+0x90/0x160
[ 40.609097][ T146] ? dev_set_mac_address+0x1f0/0x3f0
[ 40.609758][ T146] dev_set_mac_address+0x1f0/0x3f0
[ 40.610402][ T146] ? __local_bh_enable_ip+0xe9/0x1b0
[ 40.611071][ T146] ? bond_hw_addr_flush+0x77/0x100 [bonding]
[ 40.611823][ T146] ? netdev_notify_peers+0xc0/0xc0
[ 40.612461][ T146] ? bond_hw_addr_flush+0x77/0x100 [bonding]
[ 40.613213][ T146] ? bond_hw_addr_flush+0x77/0x100 [bonding]
[ 40.613963][ T146] ? __local_bh_enable_ip+0xe9/0x1b0
[ 40.614631][ T146] ? bond_time_in_interval.isra.31+0x90/0x90 [bonding]
[ 40.615484][ T146] ? __bond_release_one+0x9f0/0x12c0 [bonding]
[ 40.616230][ T146] __bond_release_one+0x9f0/0x12c0 [bonding]
[ 40.616949][ T146] ? bond_enslave+0x47c0/0x47c0 [bonding]
[ 40.617642][ T146] ? lock_downgrade+0x730/0x730
[ 40.618218][ T146] ? check_flags.part.42+0x450/0x450
[ 40.618850][ T146] ? __mutex_unlock_slowpath+0xd0/0x670
[ 40.619519][ T146] ? trace_hardirqs_on+0x30/0x180
[ 40.620117][ T146] ? wait_for_completion+0x250/0x250
[ 40.620754][ T146] bond_netdev_event+0x822/0x970 [bonding]
[ 40.621460][ T146] ? __module_text_address+0x13/0x140
[ 40.622097][ T146] notifier_call_chain+0x90/0x160
[ 40.622806][ T146] rollback_registered_many+0x660/0xcf0
[ 40.623522][ T146] ? netif_set_real_num_tx_queues+0x780/0x780
[ 40.624290][ T146] ? notifier_call_chain+0x90/0x160
[ 40.624957][ T146] ? netdev_upper_dev_unlink+0x114/0x180
[ 40.625686][ T146] ? __netdev_adjacent_dev_unlink_neighbour+0x30/0x30
[ 40.626421][ T146] ? mutex_is_locked+0x13/0x50
[ 40.627016][ T146] ? unregister_netdevice_queue+0xf2/0x240
[ 40.627663][ T146] unregister_netdevice_many.part.134+0x13/0x1b0
[ 40.628362][ T146] default_device_exit_batch+0x2d9/0x390
[ 40.628987][ T146] ? unregister_netdevice_many+0x40/0x40
[ 40.629615][ T146] ? dev_change_net_namespace+0xcb0/0xcb0
[ 40.630279][ T146] ? prepare_to_wait_exclusive+0x2e0/0x2e0
[ 40.630943][ T146] ? ops_exit_list.isra.9+0x97/0x140
[ 40.631554][ T146] cleanup_net+0x441/0x890
[ ... ]
Fixes: e289fd28176b ("macvlan: fix the problem when mac address changes for passthru mode")
Reported-by: syzbot+5035b1f9dc7ea4558d5a@syzkaller.appspotmail.com
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 7f327080364abccf923fa5a5b24e038eb0ba1407 ]
When a macsec interface is created, the mtu is calculated with the lower
interface's mtu value.
If the mtu of lower interface is lower than the length, which is needed
by macsec interface, macsec's mtu value will be overflowed.
So, if the lower interface's mtu is too low, macsec interface's mtu
should be set to 0.
Test commands:
ip link add dummy0 mtu 10 type dummy
ip link add macsec0 link dummy0 type macsec
ip link show macsec0
Before:
11: macsec0@dummy0: <BROADCAST,MULTICAST,M-DOWN> mtu 4294967274
After:
11: macsec0@dummy0: <BROADCAST,MULTICAST,M-DOWN> mtu 0
Fixes: c09440f7dcb3 ("macsec: introduce IEEE 802.1AE driver")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 82c9ae440857840c56e05d4fb1427ee032531346 ]
Commit b6f6118901d1 ("ipv6: restrict IPV6_ADDRFORM operation") fixed a
problem found by syzbot an unfortunate logic error meant that it
also broke IPV6_ADDRFORM.
Rearrange the checks so that the earlier test is just one of the series
of checks made before moving the socket from IPv6 to IPv4.
Fixes: b6f6118901d1 ("ipv6: restrict IPV6_ADDRFORM operation")
Signed-off-by: John Haxby <john.haxby@oracle.com>
Cc: stable@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit bd019427bf3623ee3c7d2845cf921bbf4c14846c ]
Fetching PTP sync information from mailbox is slow and can take
up to 10 milliseconds. Reduce this unnecessary delay by directly
reading the information from the corresponding registers.
Fixes: 9c33e4208bce ("cxgb4: Add PTP Hardware Clock (PHC) support")
Signed-off-by: Manoj Malviya <manojmalviya@chelsio.com>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit ce222748078592afb51b810dc154531aeba4f512 ]
In the absence of MC1, the size calculation function
cudbg_mem_region_size() was returing wrong MC size and
resulted in adapter crash. This patch adds new argument
to cudbg_mem_region_size() which will have actual size
and returns error to caller in the absence of MC1.
Fixes: a1c69520f785 ("cxgb4: collect MC memory dump")
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>"
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a6bd811f1209fe1c64c9f6fd578101d6436c6b6e upstream.
Now that we are mapping kvm_steal_time from the guest directly we
don't need keep a copy of it in kvm_vcpu_arch.st. The same is true
for the stime field.
This is part of CVE-2019-3016.
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Reviewed-by: Joao Martins <joao.m.martins@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit b043138246a41064527cf019a3d51d9f015e9796 upstream.
There is a potential race in record_steal_time() between setting
host-local vcpu->arch.st.steal.preempted to zero (i.e. clearing
KVM_VCPU_PREEMPTED) and propagating this value to the guest with
kvm_write_guest_cached(). Between those two events the guest may
still see KVM_VCPU_PREEMPTED in its copy of kvm_steal_time, set
KVM_VCPU_FLUSH_TLB and assume that hypervisor will do the right
thing. Which it won't.
Instad of copying, we should map kvm_steal_time and that will
guarantee atomicity of accesses to @preempted.
This is part of CVE-2019-3016.
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Reviewed-by: Joao Martins <joao.m.martins@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
[bwh: Backported to 4.19: No tracepoint in record_steal_time().]
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 917248144db5d7320655dbb41d3af0b8a0f3d589 upstream.
__kvm_map_gfn()'s call to gfn_to_pfn_memslot() is
* relatively expensive
* in certain cases (such as when done from atomic context) cannot be called
Stashing gfn-to-pfn mapping should help with both cases.
This is part of CVE-2019-3016.
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Reviewed-by: Joao Martins <joao.m.martins@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 1eff70a9abd46f175defafd29bc17ad456f398a7 upstream.
kvm_vcpu_(un)map operates on gfns from any current address space.
In certain cases we want to make sure we are not mapping SMRAM
and for that we can use kvm_(un)map_gfn() that we are introducing
in this patch.
This is part of CVE-2019-3016.
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Reviewed-by: Joao Martins <joao.m.martins@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit b614c6027896ff9ad6757122e84760d938cab15e upstream.
The field "page" is initialized to KVM_UNMAPPED_PAGE when it is not used
(i.e. when the memory lives outside kernel control). So this check will
always end up using kunmap even for memremap regions.
Fixes: e45adf665a53 ("KVM: Introduce a new guest mapping API")
Signed-off-by: KarimAllah Ahmed <karahmed@amazon.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit eb1f2f387db8c0d084581fb26e7faffde700bc8e upstream.
We also need to fence the memunmap part.
Fixes: e45adf665a53 ("KVM: Introduce a new guest mapping API")
Fixes: d30b214d1d0a (kvm: fix compilation on s390)
Cc: Michal Kubecek <mkubecek@suse.cz>
Cc: KarimAllah Ahmed <karahmed@amazon.de>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit d30b214d1d0addb7b2c9c78178d1501cd39a01fb upstream.
s390 does not have memremap, even though in this particular case it
would be useful.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit c011d23ba046826ccf8c4a4a6c1d01c9ccaa1403 upstream.
Commit e45adf665a53 ("KVM: Introduce a new guest mapping API", 2019-01-31)
introduced a build failure on aarch64 defconfig:
$ make -j$(nproc) ARCH=arm64 CROSS_COMPILE=aarch64-linux-gnu- O=out defconfig \
Image.gz
...
../arch/arm64/kvm/../../../virt/kvm/kvm_main.c:
In function '__kvm_map_gfn':
../arch/arm64/kvm/../../../virt/kvm/kvm_main.c:1763:9: error:
implicit declaration of function 'memremap'; did you mean 'memset_p'?
../arch/arm64/kvm/../../../virt/kvm/kvm_main.c:1763:46: error:
'MEMREMAP_WB' undeclared (first use in this function)
../arch/arm64/kvm/../../../virt/kvm/kvm_main.c:
In function 'kvm_vcpu_unmap':
../arch/arm64/kvm/../../../virt/kvm/kvm_main.c:1795:3: error:
implicit declaration of function 'memunmap'; did you mean 'vm_munmap'?
because these functions are declared in <linux/io.h> rather than <asm/io.h>,
and the former was being pulled in already on x86 but not on aarch64.
Reported-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
[bwh: Backported to 4.19: adjust context]
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit e45adf665a53df0db37f784ed87c6b57ddd81885 upstream.
In KVM, specially for nested guests, there is a dominant pattern of:
=> map guest memory -> do_something -> unmap guest memory
In addition to all this unnecessarily noise in the code due to boiler plate
code, most of the time the mapping function does not properly handle memory
that is not backed by "struct page". This new guest mapping API encapsulate
most of this boiler plate code and also handles guest memory that is not
backed by "struct page".
The current implementation of this API is using memremap for memory that is
not backed by a "struct page" which would lead to a huge slow-down if it
was used for high-frequency mapping operations. The API does not have any
effect on current setups where guest memory is backed by a "struct page".
Further patches are going to also introduce a pfn-cache which would
significantly improve the performance of the memremap case.
Signed-off-by: KarimAllah Ahmed <karahmed@amazon.de>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
[bwh: Backported to 4.19 as dependency of commit 1eff70a9abd4
"x86/kvm: Introduce kvm_(un)map_gfn()"]
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 3b013a2972d5bc344d6eaa8f24fdfe268211e45f upstream.
If L1 does not set VM_ENTRY_LOAD_BNDCFGS, then L1's BNDCFGS value must
be propagated to vmcs02 since KVM always runs with VM_ENTRY_LOAD_BNDCFGS
when MPX is supported. Because the value effectively comes from vmcs01,
vmcs02 must be updated even if vmcs12 is clean.
Fixes: 62cf9bd8118c4 ("KVM: nVMX: Fix emulation of VM_ENTRY_LOAD_BNDCFGS")
Cc: Liran Alon <liran.alon@oracle.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
[bwh: Backported to 4.19: adjust filename, context]
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 0e0ab73c9a0243736bcd779b30b717e23ba9a56d upstream.
...except RSP, which is restored by hardware as part of VM-Exit.
Paolo theorized that restoring registers from the stack after a VM-Exit
in lieu of zeroing them could lead to speculative execution with the
guest's values, e.g. if the stack accesses miss the L1 cache[1].
Zeroing XORs are dirt cheap, so just be ultra-paranoid.
Note that the scratch register (currently RCX) used to save/restore the
guest state is also zeroed as its host-defined value is loaded via the
stack, just with a MOV instead of a POP.
[1] https://patchwork.kernel.org/patch/10771539/#22441255
Fixes: 0cb5b30698fd ("kvm: vmx: Scrub hardware GPRs at VM-exit")
Cc: Jim Mattson <jmattson@google.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
[bwh: Backported to 4.19: adjust filename, context]
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 688078e7f36c293dae25b338ddc9e0a2790f6e06 upstream.
In f2fs_listxattr, there is no boundary check before
memcpy e_name to buffer.
If the e_name_len is corrupted,
unexpected memory contents may be returned to the buffer.
Signed-off-by: Randall Huang <huangrandall@google.com>
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
[bwh: Backported to 4.19: Use f2fs_msg() instead of f2fs_err()]
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 153031a301bb07194e9c37466cfce8eacb977621 upstream.
There was a recent change in blktrace.c that added a RCU protection to
`q->blk_trace` in order to fix a use-after-free issue during access.
However the change missed an edge case that can lead to dereferencing of
`bt` pointer even when it's NULL:
Coverity static analyzer marked this as a FORWARD_NULL issue with CID
1460458.
```
/kernel/trace/blktrace.c: 1904 in sysfs_blk_trace_attr_store()
1898 ret = 0;
1899 if (bt == NULL)
1900 ret = blk_trace_setup_queue(q, bdev);
1901
1902 if (ret == 0) {
1903 if (attr == &dev_attr_act_mask)
>>> CID 1460458: Null pointer dereferences (FORWARD_NULL)
>>> Dereferencing null pointer "bt".
1904 bt->act_mask = value;
1905 else if (attr == &dev_attr_pid)
1906 bt->pid = value;
1907 else if (attr == &dev_attr_start_lba)
1908 bt->start_lba = value;
1909 else if (attr == &dev_attr_end_lba)
```
Added a reassignment with RCU annotation to fix the issue.
Fixes: c780e86dd48 ("blktrace: Protect q->blk_trace with RCU")
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Bob Liu <bob.liu@oracle.com>
Reviewed-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Cengiz Can <cengiz@kernel.wtf>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit c780e86dd48ef6467a1146cf7d0fe1e05a635039 upstream.
KASAN is reporting that __blk_add_trace() has a use-after-free issue
when accessing q->blk_trace. Indeed the switching of block tracing (and
thus eventual freeing of q->blk_trace) is completely unsynchronized with
the currently running tracing and thus it can happen that the blk_trace
structure is being freed just while __blk_add_trace() works on it.
Protect accesses to q->blk_trace by RCU during tracing and make sure we
wait for the end of RCU grace period when shutting down tracing. Luckily
that is rare enough event that we can afford that. Note that postponing
the freeing of blk_trace to an RCU callback should better be avoided as
it could have unexpected user visible side-effects as debugfs files
would be still existing for a short while block tracing has been shut
down.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=205711
CC: stable@vger.kernel.org
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Tested-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reported-by: Tristan Madani <tristmd@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
[bwh: Backported to 4.19: adjust context]
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 6c8991f41546c3c472503dff1ea9daaddf9331c2 upstream.
ipv6_stub uses the ip6_dst_lookup function to allow other modules to
perform IPv6 lookups. However, this function skips the XFRM layer
entirely.
All users of ipv6_stub->ip6_dst_lookup use ip_route_output_flow (via the
ip_route_output_key and ip_route_output helpers) for their IPv4 lookups,
which calls xfrm_lookup_route(). This patch fixes this inconsistent
behavior by switching the stub to ip6_dst_lookup_flow, which also calls
xfrm_lookup_route().
This requires some changes in all the callers, as these two functions
take different arguments and have different return types.
Fixes: 5f81bd2e5d80 ("ipv6: export a stub for IPv6 symbols used by vxlan")
Reported-by: Xiumei Mu <xmu@redhat.com>
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 4.19:
- Drop change in lwt_bpf.c
- Delete now-unused "ret" in mlx5e_route_lookup_ipv6()
- Initialise "out_dev" in mlx5e_create_encap_header_ipv6() to avoid
introducing a spurious "may be used uninitialised" warning
- Adjust filenames, context, indentation]
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit c4e85f73afb6384123e5ef1bba3315b2e3ad031e upstream.
This will be used in the conversion of ipv6_stub to ip6_dst_lookup_flow,
as some modules currently pass a net argument without a socket to
ip6_dst_lookup. This is equivalent to commit 343d60aada5a ("ipv6: change
ipv6_stub_impl.ipv6_dst_lookup to take net argument").
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 4.19: adjust context]
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 35efea32b26f9aacc99bf07e0d2cdfba2028b099 ]
Previously Clock PM could not be re-enabled after being disabled by
pci_disable_link_state() because clkpm_capable was reset. Change this by
adding a clkpm_disable field similar to aspm_disable.
Link: https://lore.kernel.org/r/4e8a66db-7d53-4a66-c26c-f0037ffaa705@gmail.com
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b969261134c1b990b96ea98fe5e0fcf8ec937c04 ]
Use sas_phy_delete rather than sas_phy_free which, according to
comments, should not be called for PHYs that have been set up
successfully.
Link: https://lore.kernel.org/r/157048748876.11757.17773443136670011786.stgit@brunhilda
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Murthy Bhat <Murthy.Bhat@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 3d973b2e9a625996ee997c7303cd793b9d197c65 ]
Let's change the mapping between virtqueue_add errors to BLK_STS
statuses, so that -ENOSPC, which indicates virtqueue full is still
mapped to BLK_STS_DEV_RESOURCE, but -ENOMEM which indicates non-device
specific resource outage is mapped to BLK_STS_RESOURCE.
Signed-off-by: Halil Pasic <pasic@linux.ibm.com>
Link: https://lore.kernel.org/r/20200213123728.61216-3-pasic@linux.ibm.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b43e78f65b1d35fd3e13c7b23f9b64ea83c9ad3a ]
As the ftrace selftests can run for a long period of time, disable the
timeout that the general selftests have. If a selftest hangs, then it
probably means the machine will hang too.
Link: https://lore.kernel.org/r/alpine.LSU.2.21.1911131604170.18679@pobox.suse.cz
Suggested-by: Miroslav Benes <mbenes@suse.cz>
Tested-by: Miroslav Benes <mbenes@suse.cz>
Reviewed-by: Miroslav Benes <mbenes@suse.cz>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
Lars-Peter Clausen
Olivier Moysan
Lary Gibaud
Lars Engebretsen
Takashi Iwai
Waiman Long
Dan Carpenter
David Ahern
Florian Fainelli
Taehee Yoo
Eric Dumazet
Xiyu Yang
Marc Zyngier
Doug Berger
John Haxby
Rahul Lakkireddy
Vishal Kulkarni
Boris Ostrovsky
KarimAllah Ahmed
Christian Borntraeger
Paolo Bonzini
Sean Christopherson
Randall Huang
Cengiz Can
Jan Kara
Sabrina Dubroca
Heiner Kallweit
Murthy Bhat
Halil Pasic
Steven Rostedt (VMware)