| Age | Commit message (Collapse) | Author |
|---|
|
The MinnowBoard uses an AR803x PHY with the PCH GBE which requires
special handling. Use the MinnowBoard PCI Subsystem ID to detect this
and add a pci_device_id.driver_data structure and functions to handle
platform setup.
The AR803x does not implement the RGMII 2ns TX clock delay in the trace
routing nor via strapping. Add a detection method for the board and the
PHY and enable the TX clock delay via the registers.
This PHY will hibernate without link for 10 seconds. Ensure the PHY is
awake for probe and then disable hibernation. A future improvement would
be to convert pch_gbe to using PHYLIB and making sure we can wake the
PHY at the necessary times rather than permanently disabling it.
Backported to 3.10 from commit f1a26fdf5944ff950888ae0017e546690353f85f
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Peter Waskiewicz <peter.p.waskiewicz.jr@intel.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Joe Perches <joe@perches.com>
Cc: netdev@vger.kernel.org
|
|
Avoid using magic numbers when we have perfectly good defines just lying
around.
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Peter Waskiewicz <peter.p.waskiewicz.jr@intel.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: netdev@vger.kernel.org
|
|
This makes the error handling much more simpler than open-coding everything and
in addition makes the probe function smaller an tidier.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We may use nice macros to prefix our messages with proper device name.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Function wait_for_xmitr is invoked only on functions that either depend
on CONFIG_CONSOLE_POLL or CONFIG_SERIAL_PCH_UART_CONSOLE.
This patch fixes the following warning:
drivers/tty/serial/pch_uart.c:1504:13: warning: ‘wait_for_xmitr’ defined but not used [-Wunused-function]
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Storing one struct per known board would be overkill. Pre-cast the
driver_data pointer to an unsigned long to avoid the pointer to int
compiler warning:
drivers/tty/serial/pch_uart.c:431:10: warning: cast from pointer to
integer of different size [-Wpointer-to-int-cast]
Unify the signed-ness of the baud and uartclk types throughout the
driver.
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The dmi_table is best accessed from the probe function, which is not
an __init function. Drop the __initdata annotation from the dmi_table
to avoid the section mismatch compiler warnings:
WARNING: drivers/tty/serial/pch_uart.o(.text+0x4871): Section mismatch
in reference from the function pch_uart_init_port() to the variable
.init.data:pch_uart_dmi_table
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use the DMI interface rather than manually matching DMI strings.
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Cc: Michael Brunner <mibru@gmx.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This is the 3.10.10 stable release
|
|
The proc interfaces in the 3.10 kernel have changed in a manner that is not
compatible with yaffs2. As discussed in the following thread:
http://www.aleph1.co.uk/lurker/message/20130724.003329.c28842f5.en.html
The solution is to temporarily remove procfs support, which allows the FS to
continue to be used.
Based on this patch:
https://dev.openwrt.org/export/37617/trunk/target/linux/generic/patches-3.10/515-yaffs-3.10-disable-proc-entry.patch
We disable procfs for any kernel greater than 3.9
Signed-off-by: Bruce Ashfield <bruce.ashfield@windriver.com>
|
|
Based on the openwrt patch:
https://dev.openwrt.org/export/37617/trunk/target/linux/generic/patches-3.10/512-yaffs-3.5-convert-to-use-kuid_t-kgid_t.patch
To fix compliation issues, we convert the latest yaffs2 to use kuid_t and
kgid_t for kernels greater than 3.9.
Signed-off-by: Bruce Ashfield <bruce.ashfield@windriver.com>
empty message aborts the commit.
|
|
The initial integration of yaffs2 was via the single kernel version variant
of the code. That code has some fundamental issues, and isn't a suitable
base.
With this commit, we restore the multi kernel functionality and with it all
required include files.
Signed-off-by: Bruce Ashfield <bruce.ashfield@windriver.com>
|
|
|
|
commit e49c7c374e7aacd1f04ecbc21d9dbbeeea4a77d6 upstream.
Journal writes need to be marked FUA, not just REQ_FLUSH. And btree node
writes have... weird ordering requirements.
Signed-off-by: Kent Overstreet <koverstreet@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5c694129c8db6d89c9be109049a16510b2f70f6d upstream.
bio_alloc_bioset returns NULL on failure. This fix adds a missing check
for potential NULL pointer dereferencing.
Signed-off-by: Kumar Amit Mehta <gmate.amit@gmail.com>
Signed-off-by: Kent Overstreet <koverstreet@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit dab9bf41b23fe700c4a74133e41eb6a21706031e upstream.
1. MEI_INTEROP_TIMEOUT is in seconds not in jiffies
so we use mei_secs_to_jiffies macro
While cold boot is fast this is relevant in resume
2. wait_event_interruptible_timeout can return with
-ERESTARTSYS so do not override it with -ETIMEDOUT
3.Adjust error message
Tested-by: Shuah Khan <shuah.kh@samsung.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 99f22c4ef24cf87b0dae6aabe6b5e620b62961d9 upstream.
When powering up, we don't have to clean up the device state
nothing is connected.
Tested-by: Shuah Khan <shuah.kh@samsung.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 315a383ad7dbd484fafb93ef08038e3dbafbb7a8 upstream.
ME HW ready bit is down after hw reset was asserted or on error.
Only on error we need to enter the reset flow, additional reset
need to be prevented when reset was triggered during
initialization , power up/down or a reset is already in progress
Tested-by: Shuah Khan <shuah.kh@samsung.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3bc38cbceb85881a8eb789ee1aa56678038b1909 upstream.
If there are UNUSABLE regions in the machine memory map, dom0 will
attempt to map them 1:1 which is not permitted by Xen and the kernel
will crash.
There isn't anything interesting in the UNUSABLE region that the dom0
kernel needs access to so we can avoid making the 1:1 mapping and
treat it as RAM.
We only do this for dom0, as that is where tboot case shows up.
A PV domU could have an UNUSABLE region in its pseudo-physical map
and would need to be handled in another patch.
This fixes a boot failure on hosts with tboot.
tboot marks a region in the e820 map as unusable and the dom0 kernel
would attempt to map this region and Xen does not permit unusable
regions to be mapped by guests.
(XEN) 0000000000000000 - 0000000000060000 (usable)
(XEN) 0000000000060000 - 0000000000068000 (reserved)
(XEN) 0000000000068000 - 000000000009e000 (usable)
(XEN) 0000000000100000 - 0000000000800000 (usable)
(XEN) 0000000000800000 - 0000000000972000 (unusable)
tboot marked this region as unusable.
(XEN) 0000000000972000 - 00000000cf200000 (usable)
(XEN) 00000000cf200000 - 00000000cf38f000 (reserved)
(XEN) 00000000cf38f000 - 00000000cf3ce000 (ACPI data)
(XEN) 00000000cf3ce000 - 00000000d0000000 (reserved)
(XEN) 00000000e0000000 - 00000000f0000000 (reserved)
(XEN) 00000000fe000000 - 0000000100000000 (reserved)
(XEN) 0000000100000000 - 0000000630000000 (usable)
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
[v1: Altered the patch and description with domU's with UNUSABLE regions]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 41aacc1eea645c99edbe8fbcf78a97dc9b862adc upstream.
This is the updated version of df54d6fa5427 ("x86 get_unmapped_area():
use proper mmap base for bottom-up direction") that only randomizes the
mmap base address once.
Signed-off-by: Radu Caragea <sinaelgl@gmail.com>
Reported-and-tested-by: Jeff Shorey <shoreyjeff@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Michel Lespinasse <walken@google.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Adrian Sendroiu <molecula2788@gmail.com>
Cc: Kamal Mostafa <kamal@canonical.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5ea80f76a56605a190a7ea16846c82aa63dbd0aa upstream.
This reverts commit df54d6fa54275ce59660453e29d1228c2b45a826.
The commit isn't necessarily wrong, but because it recalculates the
random mmap_base every time, it seems to confuse user memory allocators
that expect contiguous mmap allocations even when the mmap address isn't
specified.
In particular, the MATLAB Java runtime seems to be unhappy. See
https://bugzilla.kernel.org/show_bug.cgi?id=60774
So we'll want to apply the random offset only once, and Radu has a patch
for that. Revert this older commit in order to apply the other one.
Reported-by: Jeff Shorey <shoreyjeff@gmail.com>
Cc: Radu Caragea <sinaelgl@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 35dc248383bbab0a7203fca4d722875bc81ef091 upstream.
There is a nasty bug in the SCSI SG_IO ioctl that in some circumstances
leads to one process writing data into the address space of some other
random unrelated process if the ioctl is interrupted by a signal.
What happens is the following:
- A process issues an SG_IO ioctl with direction DXFER_FROM_DEV (ie the
underlying SCSI command will transfer data from the SCSI device to
the buffer provided in the ioctl)
- Before the command finishes, a signal is sent to the process waiting
in the ioctl. This will end up waking up the sg_ioctl() code:
result = wait_event_interruptible(sfp->read_wait,
(srp_done(sfp, srp) || sdp->detached));
but neither srp_done() nor sdp->detached is true, so we end up just
setting srp->orphan and returning to userspace:
srp->orphan = 1;
write_unlock_irq(&sfp->rq_list_lock);
return result; /* -ERESTARTSYS because signal hit process */
At this point the original process is done with the ioctl and
blithely goes ahead handling the signal, reissuing the ioctl, etc.
- Eventually, the SCSI command issued by the first ioctl finishes and
ends up in sg_rq_end_io(). At the end of that function, we run through:
write_lock_irqsave(&sfp->rq_list_lock, iflags);
if (unlikely(srp->orphan)) {
if (sfp->keep_orphan)
srp->sg_io_owned = 0;
else
done = 0;
}
srp->done = done;
write_unlock_irqrestore(&sfp->rq_list_lock, iflags);
if (likely(done)) {
/* Now wake up any sg_read() that is waiting for this
* packet.
*/
wake_up_interruptible(&sfp->read_wait);
kill_fasync(&sfp->async_qp, SIGPOLL, POLL_IN);
kref_put(&sfp->f_ref, sg_remove_sfp);
} else {
INIT_WORK(&srp->ew.work, sg_rq_end_io_usercontext);
schedule_work(&srp->ew.work);
}
Since srp->orphan *is* set, we set done to 0 (assuming the
userspace app has not set keep_orphan via an SG_SET_KEEP_ORPHAN
ioctl), and therefore we end up scheduling sg_rq_end_io_usercontext()
to run in a workqueue.
- In workqueue context we go through sg_rq_end_io_usercontext() ->
sg_finish_rem_req() -> blk_rq_unmap_user() -> ... ->
bio_uncopy_user() -> __bio_copy_iov() -> copy_to_user().
The key point here is that we are doing copy_to_user() on a
workqueue -- that is, we're on a kernel thread with current->mm
equal to whatever random previous user process was scheduled before
this kernel thread. So we end up copying whatever data the SCSI
command returned to the virtual address of the buffer passed into
the original ioctl, but it's quite likely we do this copying into a
different address space!
As suggested by James Bottomley <James.Bottomley@hansenpartnership.com>,
add a check for current->mm (which is NULL if we're on a kernel thread
without a real userspace address space) in bio_uncopy_user(), and skip
the copy if we're on a kernel thread.
There's no reason that I can think of for any caller of bio_uncopy_user()
to want to do copying on a kernel thread with a random active userspace
address space.
Huge thanks to Costa Sapuntzakis <costa@purestorage.com> for the
original pointer to this bug in the sg code.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Tested-by: David Milburn <dmilburn@redhat.com>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f5944daa0a72316077435c18a6571e73ed338332 upstream.
We want ppc64 to be able to select between optimised assembly
checksum routines in big endian and the generic lib/checksum.c
routines in little endian.
The lpfc driver is forcing CONFIG_GENERIC_CSUM on which means
we are unable to make the decision to enable it in the arch
Kconfig. If the option exists it is always forced on.
This got introduced in 3.10 via commit 6a7252fdb0c3 ([SCSI] lpfc:
fix up Kconfig dependencies). I spoke to Randy about it and
the original issue was with CRC_T10DIF not being defined.
As such, remove the select of CONFIG_GENERIC_CSUM.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 924dd584b198a58aa7cb3efefd8a03326550ce8f upstream.
BUG: sleeping function called from invalid context at kernel/workqueue.c:2752
in_atomic(): 1, irqs_disabled(): 1, pid: 360, name: zfcperp0.0.1700
CPU: 1 Not tainted 3.9.3+ #69
Process zfcperp0.0.1700 (pid: 360, task: 0000000075b7e080, ksp: 000000007476bc30)
<snip>
Call Trace:
([<00000000001165de>] show_trace+0x106/0x154)
[<00000000001166a0>] show_stack+0x74/0xf4
[<00000000006ff646>] dump_stack+0xc6/0xd4
[<000000000017f3a0>] __might_sleep+0x128/0x148
[<000000000015ece8>] flush_work+0x54/0x1f8
[<00000000001630de>] __cancel_work_timer+0xc6/0x128
[<00000000005067ac>] scsi_device_dev_release_usercontext+0x164/0x23c
[<0000000000161816>] execute_in_process_context+0x96/0xa8
[<00000000004d33d8>] device_release+0x60/0xc0
[<000000000048af48>] kobject_release+0xa8/0x1c4
[<00000000004f4bf2>] __scsi_iterate_devices+0xfa/0x130
[<000003ff801b307a>] zfcp_erp_strategy+0x4da/0x1014 [zfcp]
[<000003ff801b3caa>] zfcp_erp_thread+0xf6/0x2b0 [zfcp]
[<000000000016b75a>] kthread+0xf2/0xfc
[<000000000070c9de>] kernel_thread_starter+0x6/0xc
[<000000000070c9d8>] kernel_thread_starter+0x0/0xc
Apparently, the ref_count for some scsi_device drops down to zero,
triggering device removal through execute_in_process_context(), while
the lldd error recovery thread iterates through a scsi device list.
Unfortunately, execute_in_process_context() decides to immediately
execute that device removal function, instead of scheduling asynchronous
execution, since it detects process context and thinks it is safe to do
so. But almost all calls to shost_for_each_device() in our lldd are
inside spin_lock_irq, even in thread context. Obviously, schedule()
inside spin_lock_irq sections is a bad idea.
Change the lldd to use the proper iterator function,
__shost_for_each_device(), in combination with required locking.
Occurences that need to be changed include all calls in zfcp_erp.c,
since those might be executed in zfcp error recovery thread context
with a lock held.
Other occurences of shost_for_each_device() in zfcp_fsf.c do not
need to be changed (no process context, no surrounding locking).
The problem was introduced in Linux 2.6.37 by commit
b62a8d9b45b971a67a0f8413338c230e3117dff5
"[SCSI] zfcp: Use SCSI device data zfcp_scsi_dev instead of zfcp_unit".
Reported-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Peschke <mpeschke@linux.vnet.ibm.com>
Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d79ff142624e1be080ad8d09101f7004d79c36e1 upstream.
This patch adds wait_event_interruptible_lock_irq_timeout(), which is a
straight-forward descendant of wait_event_interruptible_timeout() and
wait_event_interruptible_lock_irq().
The zfcp driver used to call wait_event_interruptible_timeout()
in combination with some intricate and error-prone locking. Using
wait_event_interruptible_lock_irq_timeout() as a replacement
nicely cleans up that locking.
This rework removes a situation that resulted in a locking imbalance
in zfcp_qdio_sbal_get():
BUG: workqueue leaked lock or atomic: events/1/0xffffff00/10
last function: zfcp_fc_wka_port_offline+0x0/0xa0 [zfcp]
It was introduced by commit c2af7545aaff3495d9bf9a7608c52f0af86fb194
"[SCSI] zfcp: Do not wait for SBALs on stopped queue", which had a new
code path related to ZFCP_STATUS_ADAPTER_QDIOUP that took an early exit
without a required lock being held. The problem occured when a
special, non-SCSI I/O request was being submitted in process context,
when the adapter's queues had been torn down. In this case the bug
surfaced when the Fibre Channel port connection for a well-known address
was closed during a concurrent adapter shut-down procedure, which is a
rare constellation.
This patch also fixes these warnings from the sparse tool (make C=1):
drivers/s390/scsi/zfcp_qdio.c:224:12: warning: context imbalance in
'zfcp_qdio_sbal_check' - wrong count at exit
drivers/s390/scsi/zfcp_qdio.c:244:5: warning: context imbalance in
'zfcp_qdio_sbal_get' - unexpected unlock
Last but not least, we get rid of that crappy lock-unlock-lock
sequence at the beginning of the critical section.
It is okay to call zfcp_erp_adapter_reopen() with req_q_lock held.
Reported-by: Mikulas Patocka <mpatocka@redhat.com>
Reported-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Peschke <mpeschke@linux.vnet.ibm.com>
Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit eabc4ac5d7606a57ee2b7308cb7323ea8f60183b upstream.
As Arjan pointed out, we mustn't do anything related to PCI
configuration until the device is properly enabled with
pci_enable_device().
Reported-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9186a1fd9ed190739423db84bc344d258ef3e3d7 upstream.
If channel switch is pending and we remove interface we can
crash like showed below due to passing NULL vif to mac80211:
BUG: unable to handle kernel paging request at fffffffffffff8cc
IP: [<ffffffff8130924d>] strnlen+0xd/0x40
Call Trace:
[<ffffffff8130ad2e>] string.isra.3+0x3e/0xd0
[<ffffffff8130bf99>] vsnprintf+0x219/0x640
[<ffffffff8130c481>] vscnprintf+0x11/0x30
[<ffffffff81061585>] vprintk_emit+0x115/0x4f0
[<ffffffff81657bd5>] printk+0x61/0x63
[<ffffffffa048987f>] ieee80211_chswitch_done+0xaf/0xd0 [mac80211]
[<ffffffffa04e7b34>] iwl_chswitch_done+0x34/0x40 [iwldvm]
[<ffffffffa04f83c3>] iwlagn_commit_rxon+0x2a3/0xdc0 [iwldvm]
[<ffffffffa04ebc50>] ? iwlagn_set_rxon_chain+0x180/0x2c0 [iwldvm]
[<ffffffffa04e5e76>] iwl_set_mode+0x36/0x40 [iwldvm]
[<ffffffffa04e5f0d>] iwlagn_mac_remove_interface+0x8d/0x1b0 [iwldvm]
[<ffffffffa0459b3d>] ieee80211_do_stop+0x29d/0x7f0 [mac80211]
This is because we nulify ctx->vif in iwlagn_mac_remove_interface()
before calling some other functions that teardown interface. To fix
just check ctx->vif on iwl_chswitch_done(). We should not call
ieee80211_chswitch_done() as channel switch works were already canceled
by mac80211 in ieee80211_do_stop() -> ieee80211_mgd_stop().
Resolve:
https://bugzilla.redhat.com/show_bug.cgi?id=979581
Reported-by: Lukasz Jagiello <jagiello.lukasz@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8ffff94d20b7eb446e848e0046107d51b17a20a8 upstream.
Fixing support for the Silicon Image 3826 port multiplier, by applying
to it the same quirks applied to the Silicon Image 3726. Specifically
fixes the repeated timeout/reset process which previously afflicted
the 3726, as described from line 290. Slightly based on notes from:
https://bugzilla.redhat.com/show_bug.cgi?id=890237
Signed-off-by: Terry Suereth <terry.suereth@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 909bd5926d474e275599094acad986af79671ac9 upstream.
We want the data stored in "addr" and "qual", but the extra ampersands
mean we are copying stack data instead.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 99bbdfa6bdcb4bdf5be914a48e9b46941bf30819 upstream.
Before this patch, I was seeing the following lockdep splat on my
MPC8315 (PPC32) target:
[ 9.086051] =================================
[ 9.090393] [ INFO: inconsistent lock state ]
[ 9.094744] 3.9.7-ajf-gc39503d #1 Not tainted
[ 9.099087] ---------------------------------
[ 9.103432] inconsistent {HARDIRQ-ON-W} -> {IN-HARDIRQ-W} usage.
[ 9.109431] scsi_eh_1/39 [HC1[1]:SC0[0]:HE0:SE1] takes:
[ 9.114642] (&(&host->lock)->rlock){?.+...}, at: [<c02f4168>] sata_fsl_interrupt+0x50/0x250
[ 9.123137] {HARDIRQ-ON-W} state was registered at:
[ 9.128004] [<c006cdb8>] lock_acquire+0x90/0xf4
[ 9.132737] [<c043ef04>] _raw_spin_lock+0x34/0x4c
[ 9.137645] [<c02f3560>] fsl_sata_set_irq_coalescing+0x68/0x100
[ 9.143750] [<c02f36a0>] sata_fsl_init_controller+0xa8/0xc0
[ 9.149505] [<c02f3f10>] sata_fsl_probe+0x17c/0x2e8
[ 9.154568] [<c02acc90>] driver_probe_device+0x90/0x248
[ 9.159987] [<c02acf0c>] __driver_attach+0xc4/0xc8
[ 9.164964] [<c02aae74>] bus_for_each_dev+0x5c/0xa8
[ 9.170028] [<c02ac218>] bus_add_driver+0x100/0x26c
[ 9.175091] [<c02ad638>] driver_register+0x88/0x198
[ 9.180155] [<c0003a24>] do_one_initcall+0x58/0x1b4
[ 9.185226] [<c05aeeac>] kernel_init_freeable+0x118/0x1c0
[ 9.190823] [<c0004110>] kernel_init+0x18/0x108
[ 9.195542] [<c000f6b8>] ret_from_kernel_thread+0x64/0x6c
[ 9.201142] irq event stamp: 160
[ 9.204366] hardirqs last enabled at (159): [<c043f778>] _raw_spin_unlock_irq+0x30/0x50
[ 9.212469] hardirqs last disabled at (160): [<c000f414>] reenable_mmu+0x30/0x88
[ 9.219867] softirqs last enabled at (144): [<c002ae5c>] __do_softirq+0x168/0x218
[ 9.227435] softirqs last disabled at (137): [<c002b0d4>] irq_exit+0xa8/0xb4
[ 9.234481]
[ 9.234481] other info that might help us debug this:
[ 9.240995] Possible unsafe locking scenario:
[ 9.240995]
[ 9.246898] CPU0
[ 9.249337] ----
[ 9.251776] lock(&(&host->lock)->rlock);
[ 9.255878] <Interrupt>
[ 9.258492] lock(&(&host->lock)->rlock);
[ 9.262765]
[ 9.262765] *** DEADLOCK ***
[ 9.262765]
[ 9.268684] no locks held by scsi_eh_1/39.
[ 9.272767]
[ 9.272767] stack backtrace:
[ 9.277117] Call Trace:
[ 9.279589] [cfff9da0] [c0008504] show_stack+0x48/0x150 (unreliable)
[ 9.285972] [cfff9de0] [c0447d5c] print_usage_bug.part.35+0x268/0x27c
[ 9.292425] [cfff9e10] [c006ace4] mark_lock+0x2ac/0x658
[ 9.297660] [cfff9e40] [c006b7e4] __lock_acquire+0x754/0x1840
[ 9.303414] [cfff9ee0] [c006cdb8] lock_acquire+0x90/0xf4
[ 9.308745] [cfff9f20] [c043ef04] _raw_spin_lock+0x34/0x4c
[ 9.314250] [cfff9f30] [c02f4168] sata_fsl_interrupt+0x50/0x250
[ 9.320187] [cfff9f70] [c0079ff0] handle_irq_event_percpu+0x90/0x254
[ 9.326547] [cfff9fc0] [c007a1fc] handle_irq_event+0x48/0x78
[ 9.332220] [cfff9fe0] [c007c95c] handle_level_irq+0x9c/0x104
[ 9.337981] [cfff9ff0] [c000d978] call_handle_irq+0x18/0x28
[ 9.343568] [cc7139f0] [c000608c] do_IRQ+0xf0/0x1a8
[ 9.348464] [cc713a20] [c000fc8c] ret_from_except+0x0/0x14
[ 9.353983] --- Exception: 501 at _raw_spin_unlock_irq+0x40/0x50
[ 9.353983] LR = _raw_spin_unlock_irq+0x30/0x50
[ 9.364839] [cc713af0] [c043db10] wait_for_common+0xac/0x188
[ 9.370513] [cc713b30] [c02ddee4] ata_exec_internal_sg+0x2b0/0x4f0
[ 9.376699] [cc713be0] [c02de18c] ata_exec_internal+0x68/0xa8
[ 9.382454] [cc713c20] [c02de4b8] ata_dev_read_id+0x158/0x594
[ 9.388205] [cc713ca0] [c02ec244] ata_eh_recover+0xd88/0x13d0
[ 9.393962] [cc713d20] [c02f2520] sata_pmp_error_handler+0xc0/0x8ac
[ 9.400234] [cc713dd0] [c02ecdc8] ata_scsi_port_error_handler+0x464/0x5e8
[ 9.407023] [cc713e10] [c02ecfd0] ata_scsi_error+0x84/0xb8
[ 9.412528] [cc713e40] [c02c4974] scsi_error_handler+0xd8/0x47c
[ 9.418457] [cc713eb0] [c004737c] kthread+0xa8/0xac
[ 9.423355] [cc713f40] [c000f6b8] ret_from_kernel_thread+0x64/0x6c
This fix was suggested by Bhushan Bharat <R65777@freescale.com>, and
was discussed in email at:
http://linuxppc.10917.n7.nabble.com/MPC8315-reboot-failure-lockdep-splat-possibly-related-tp75162.html
Same patch successfully tested with 3.9.7. linux-next compiled but
not tested on hardware.
This patch is based off linux-next tag next-20130819
(which is commit 66a01bae29d11916c09f9f5a937cafe7d402e4a5 )
Signed-off-by: Anthony Foiani <anthony.foiani@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 52d5b9aba1f5790ca3231c262979c2c3e26dd99b upstream.
Commit 94ae9843 (usb: phy: rename all phy drivers to phy-$name-usb.c)
renamed drivers/usb/phy/otg_fsm.h to drivers/usb/phy/phy-fsm-usb.h
but changed drivers/usb/phy/phy-fsm-usb.c to include not existing
"phy-otg-fsm.h" instead of new "phy-fsm-usb.h". This breaks building:
...
drivers/usb/phy/phy-fsm-usb.c:32:25: fatal error: phy-otg-fsm.h: No such file or directory
compilation terminated.
make[3]: *** [drivers/usb/phy/phy-fsm-usb.o] Error 1
This commit also missed to modify drivers/usb/phy/phy-fsl-usb.h
to include new "phy-fsm-usb.h" instead of "otg_fsm.h" resulting
in another build breakage:
...
In file included from drivers/usb/phy/phy-fsl-usb.c:46:0:
drivers/usb/phy/phy-fsl-usb.h:18:21: fatal error: otg_fsm.h: No such file or directory
compilation terminated.
make[3]: *** [drivers/usb/phy/phy-fsl-usb.o] Error 1
Fix both issues.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 93dbc1b3b506e16c1f6d5b5dcfe756a85cb1dc58 upstream.
Being a low-level component, various drivers (e.g. olpc-battery) assume
that it is ok to communicate with the OLPC Embedded Controller during
probe. Therefore the OLPC EC driver must be initialised before other
drivers try to use it. This was the case until it was recently moved
out of arch/x86 and restructured around commits ac2504151f5a ("Platform:
OLPC: turn EC driver into a platform_driver") and 85f90cf6ca56 ("x86:
OLPC: switch over to using new EC driver on x86").
Use arch_initcall so that olpc-ec is readied earlier, matching the
previous behaviour.
Fixes a regression introduced in Linux-3.6 where various drivers such as
olpc-battery and olpc-xo1-sci failed to load due to an inability to
communicate with the EC. The user-visible effect was a lack of battery
monitoring, missing ebook/lid switch input devices, etc.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Cc: Andres Salomon <dilinger@queued.net>
Cc: Paul Fox <pgf@laptop.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
error detection
commit 4bf93b50fd04118ac7f33a3c2b8a0a1f9fa80bc9 upstream.
Fix the issue with improper counting number of flying bio requests for
BIO_EOPNOTSUPP error detection case.
The sb_nbio must be incremented exactly the same number of times as
complete() function was called (or will be called) because
nilfs_segbuf_wait() will call wail_for_completion() for the number of
times set to sb_nbio:
do {
wait_for_completion(&segbuf->sb_bio_event);
} while (--segbuf->sb_nbio > 0);
Two functions complete() and wait_for_completion() must be called the
same number of times for the same sb_bio_event. Otherwise,
wait_for_completion() will hang or leak.
Signed-off-by: Vyacheslav Dubeyko <slava@dubeyko.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Tested-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
error
commit 2df37a19c686c2d7c4e9b4ce1505b5141e3e5552 upstream.
Remove double call of bio_put() in nilfs_end_bio_write() for the case of
BIO_EOPNOTSUPP error detection. The issue was found by Dan Carpenter
and he suggests first version of the fix too.
Signed-off-by: Vyacheslav Dubeyko <slava@dubeyko.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Tested-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9e40127526e857fa3f29d51e83277204fbdfc6ba upstream.
Already existing property flags are filled wrong for properties created from
initial FDT. This could cause problems if this DYNAMIC device-tree functions
are used later, i.e. properties are attached/detached/replaced. Simply dumping
flags from the running system show, that some initial static (not allocated via
kzmalloc()) nodes are marked as dynamic.
I putted some debug extensions to property_proc_show(..) :
..
+ if (OF_IS_DYNAMIC(pp))
+ pr_err("DEBUG: xxx : OF_IS_DYNAMIC\n");
+ if (OF_IS_DETACHED(pp))
+ pr_err("DEBUG: xxx : OF_IS_DETACHED\n");
when you operate on the nodes (e.g.: ~$ cat /proc/device-tree/*some_node*) you
will see that those flags are filled wrong, basically in most cases it will dump
a DYNAMIC or DETACHED status, which is in not true.
(BTW. this OF_IS_DETACHED is a own define for debug purposes which which just
make a test_bit(OF_DETACHED, &x->_flags)
If nodes are dynamic kernel is allowed to kfree() them. But it will crash
attempting to do so on the nodes from FDT -- they are not allocated via
kzmalloc().
Signed-off-by: Wladislav Wiebe <wladislav.kw@gmail.com>
Acked-by: Alexander Sverdlin <alexander.sverdlin@nsn.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 884020bf3d2a3787a1cc6df902e98e0eec60330b upstream.
After any "soft gfx reset" we must manually invalidate the TLBs
associated with each ring. Empirically, it seems that a
suspend/resume or D3-D0 cycle count as a "soft reset". The symptom is
that the hardware would fail to note the new address for its status
page, and so it would continue to write the shadow registers and
breadcrumbs into the old physical address (now used by something
completely different, scary). Whereas the driver would read the new
status page and never see any progress, it would appear that the GPU
hung immediately upon resume.
Based on a patch by naresh kumar kachhi <naresh.kumar.kacchi@intel.com>
Reported-by: Thiago Macieira <thiago@kde.org>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=64725
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Thiago Macieira <thiago@kde.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d43a93c8d9bc4e0dc0293b6458c077c3c797594f upstream.
This bug (introduced in 3.10) in WREG32_OR made
commit d3418eacad403033e95e49dc14afa37c2112c134
"drm/radeon/evergreen: setup HDMI before enabling it"
cause a regression. Sometimes audio over HDMI wasn't working, sometimes
display was corrupted.
This fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=60687
https://bugzilla.kernel.org/show_bug.cgi?id=60709
https://bugs.freedesktop.org/show_bug.cgi?id=67767
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 112a6d0c071808f6d48354fc8834a574e5dcefc0 upstream.
When the message buffer is currently moving block until it is idle again.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 022374c02e357ac82e98dd2689fb2efe05723d69 upstream.
Uses the wrong array size for some asics which can lead
to garbage getting written to registers.
Fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=60674
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3955dfa8216f712bc204a5ad2f4e51efff252fde upstream.
Commit dcd7b8bd63cb81c5b973bf86510ca3c80bbbd162 ("staging: comedi: put
module _after_ detach" by myself) reversed a couple of calls in
`comedi_device_attach()` when recovering from an error returned by the
low-level driver's 'attach' handler. Unfortunately, that introduced a
NULL pointer dereference bug as `dev->driver` is NULL after the call to
`comedi_device_detach()`. We still have a pointer to the low-level
comedi driver structure in the `driv` variable, so use that instead.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ac124504ecf6b20a2457d873d0728a8b991a5b0c upstream.
Commit f6f91b0d9fd9 ("ARM: allow kuser helpers to be removed from the
vector page") introduced some help text for the CONFIG_KUSER_HELPERS
option which is rather contradictory.
Let's fix that, and improve it a little.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ee7538a008a45050c8f706d38b600f55953169f9 upstream.
This is a port of c95eb3184ea1 ("ARM: 7809/1: perf: fix event validation
for software group leaders") to arm64, which fixes a panic in the arm64
perf backend found as a result of Vince's fuzzing tool.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 868f6fea8fa63f09acbfa93256d0d2abdcabff79 upstream.
This is a port of d9f966357b14 ("ARM: 7810/1: perf: Fix array out of
bounds access in armpmu_map_hw_event()") to arm64, which fixes an oops
in the arm64 perf backend found as a result of Vince's fuzzing tool.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a57603ca2871ee0773b00839c1ea35c4a2d3eeb0 upstream.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit acd36357edc08649e85ff15dc4ed62353c912eff upstream.
Starting with kernel v3.5, it is mandatory
to specify ECC strength when using hardware
ECC. Without this, kernel panics with a warning
of the sort:
Driver must set ecc.strength when using hardware ECC
------------[ cut here ]------------
kernel BUG at drivers/mtd/nand/nand_base.c:3519!
Fix this by specifying ECC strength for the boards
which were missing this.
Reported-by: Holger Freyther <holger@freyther.de>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4704fe4f03a5ab27e3c36184af85d5000e0f8a48 upstream.
When a event is being bound to a VCPU there is a window between the
EVTCHNOP_bind_vpcu call and the adjustment of the local per-cpu masks
where an event may be lost. The hypervisor upcalls the new VCPU but
the kernel thinks that event is still bound to the old VCPU and
ignores it.
There is even a problem when the event is being bound to the same VCPU
as there is a small window beween the clear_bit() and set_bit() calls
in bind_evtchn_to_cpu(). When scanning for pending events, the kernel
may read the bit when it is momentarily clear and ignore the event.
Avoid this by masking the event during the whole bind operation.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 84ca7a8e45dafb49cd5ca90a343ba033e2885c17 upstream.
The sizeof() argument in init_evtchn_cpu_bindings() is incorrect
resulting in only the first 64 (or 32 in 32-bit guests) ports having
their bindings being initialized to VCPU 0.
In most cases this does not cause a problem as request_irq() will set
the irq affinity which will set the correct local per-cpu mask.
However, if the request_irq() is called on a VCPU other than 0, there
is a window between the unmasking of the event and the affinity being
set were an event may be lost because it is not locally unmasked on
any VCPU. If request_irq() is called on VCPU 0 then local irqs are
disabled during the window and the race does not occur.
Fix this by initializing all NR_EVENT_CHANNEL bits in the local
per-cpu masks.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d55e37bb0f51316e552376ddc0a3fff34ca7108b upstream.
OpenFirmware wasn't quite following the protocol described in boot.txt
and the kernel has detected this through use of the sentinel value
in boot_params. OFW does zero out almost all of the stuff that it should
do, but not the sentinel.
This causes the kernel to clear olpc_ofw_header, which breaks x86 OLPC
support.
OpenFirmware has now been fixed. However, it would be nice if we could
maintain Linux compatibility with old firmware versions. To do that, we just
have to avoid zeroing out olpc_ofw_header.
OFW does not write to any other parts of the header that are being zapped
by the sentinel-detection code, and all users of olpc_ofw_header are
somewhat protected through checking for the OLPC_OFW_SIG magic value
before using it. So this should not cause any problems for anyone.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Link: http://lkml.kernel.org/r/20130809221420.618E6FAB03@dev.laptop.org
Acked-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 52e220d357a38cb29fa2e29f34ed94c1d66357f4 upstream.
This should actually be returning an ERR_PTR on error instead of NULL.
That was how it was designed and all the callers expect it.
[AV: actually, that's what "VFS: Make clone_mnt()/copy_tree()/collect_mounts()
return errors" missed - originally collect_mounts() was expected to return
NULL on failure]
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1206ff4ff9d2ef7468a355328bc58ac6ebf5be44 upstream.
Patch fixes zd1201 not to use stack as URB transfer_buffer. URB buffers need
to be DMA-able, which stack is not.
Patch is only compile tested.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@iki.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
Darren Hart
Andy Shevchenko
Luis Henriques
Bruce Ashfield
Greg Kroah-Hartman
Kent Overstreet
Kumar Amit Mehta
Tomas Winkler
David Vrabel
Radu Caragea
Linus Torvalds
Roland Dreier
Anton Blanchard
Martin Peschke
Emmanuel Grumbach
Stanislaw Gruszka
Terry Suereth
Dan Carpenter
Anthony Foiani
Anatolij Gustschin
Daniel Drake
Vyacheslav Dubeyko
Wladislav Wiebe
Chris Wilson
Rafał Miłecki
Christian König
Alex Deucher
Ian Abbott
Nicolas Pitre
Will Deacon
Nicolas Ferre
Sekhar Nori
Jussi Kivilinna