1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
|
/*
comedi/drivers/pcmda12.c
Driver for Winsystems PC-104 based PCM-D/A-12 8-channel AO board.
COMEDI - Linux Control and Measurement Device Interface
Copyright (C) 2006 Calin A. Culianu <calin@ajvar.org>
This program is free software; you can redistribute it and/or modify
it under the terms of the GNU General Public License as published by
the Free Software Foundation; either version 2 of the License, or
(at your option) any later version.
This program is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
GNU General Public License for more details.
You should have received a copy of the GNU General Public License
along with this program; if not, write to the Free Software
Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
*/
/*
Driver: pcmda12
Description: A driver for the Winsystems PCM-D/A-12
Devices: [Winsystems] PCM-D/A-12 (pcmda12)
Author: Calin Culianu <calin@ajvar.org>
Updated: Fri, 13 Jan 2006 12:01:01 -0500
Status: works
A driver for the relatively straightforward-to-program PCM-D/A-12.
This board doesn't support commands, and the only way to set its
analog output range is to jumper the board. As such,
comedi_data_write() ignores the range value specified.
The board uses 16 consecutive I/O addresses starting at the I/O port
base address. Each address corresponds to the LSB then MSB of a
particular channel from 0-7.
Note that the board is not ISA-PNP capable and thus
needs the I/O port comedi_config parameter.
Note that passing a nonzero value as the second config option will
enable "simultaneous xfer" mode for this board, in which AO writes
will not take effect until a subsequent read of any AO channel. This
is so that one can speed up programming by preloading all AO registers
with values before simultaneously setting them to take effect with one
read command.
Configuration Options:
[0] - I/O port base address
[1] - Do Simultaneous Xfer (see description)
*/
#include "../comedidev.h"
#include <linux/pci.h> /* for PCI devices */
#define SDEV_NO ((int)(s - dev->subdevices))
#define CHANS 8
#define IOSIZE 16
#define LSB(x) ((unsigned char)((x) & 0xff))
#define MSB(x) ((unsigned char)((((unsigned short)(x))>>8) & 0xff))
#define LSB_PORT(chan) (dev->iobase + (chan)*2)
#define MSB_PORT(chan) (LSB_PORT(chan)+1)
#define BITS 12
/*
* Bords
*/
struct pcmda12_board {
const char *name;
};
/* note these have no effect and are merely here for reference..
these are configured by jumpering the board! */
static const struct comedi_lrange pcmda12_ranges = {
3,
{
UNI_RANGE(5), UNI_RANGE(10), BIP_RANGE(5)
}
};
struct pcmda12_private {
unsigned int ao_readback[CHANS];
int simultaneous_xfer_mode;
};
#define devpriv ((struct pcmda12_private *)(dev->private))
static void zero_chans(struct comedi_device *dev)
{ /* sets up an
ASIC chip to defaults */
int i;
for (i = 0; i < CHANS; ++i) {
/* /\* do this as one instruction?? *\/ */
/* outw(0, LSB_PORT(chan)); */
outb(0, LSB_PORT(i));
outb(0, MSB_PORT(i));
}
inb(LSB_PORT(0)); /* update chans. */
}
static int ao_winsn(struct comedi_device *dev, struct comedi_subdevice *s,
struct comedi_insn *insn, unsigned int *data)
{
int i;
int chan = CR_CHAN(insn->chanspec);
/* Writing a list of values to an AO channel is probably not
* very useful, but that's how the interface is defined. */
for (i = 0; i < insn->n; ++i) {
/* /\* do this as one instruction?? *\/ */
/* outw(data[i], LSB_PORT(chan)); */
/* Need to do this as two instructions due to 8-bit bus?? */
/* first, load the low byte */
outb(LSB(data[i]), LSB_PORT(chan));
/* next, write the high byte */
outb(MSB(data[i]), MSB_PORT(chan));
/* save shadow register */
devpriv->ao_readback[chan] = data[i];
if (!devpriv->simultaneous_xfer_mode)
inb(LSB_PORT(chan));
}
/* return the number of samples written */
return i;
}
/* AO subdevices should have a read insn as well as a write insn.
Usually this means copying a value stored in devpriv->ao_readback.
However, since this driver supports simultaneous xfer then sometimes
this function actually accomplishes work.
Simultaneaous xfer mode is accomplished by loading ALL the values
you want for AO in all the channels, then READing off one of the AO
registers to initiate the instantaneous simultaneous update of all
DAC outputs, which makes all AO channels update simultaneously.
This is useful for some control applications, I would imagine.
*/
static int ao_rinsn(struct comedi_device *dev, struct comedi_subdevice *s,
struct comedi_insn *insn, unsigned int *data)
{
int i;
int chan = CR_CHAN(insn->chanspec);
for (i = 0; i < insn->n; i++) {
if (devpriv->simultaneous_xfer_mode)
inb(LSB_PORT(chan));
/* read back shadow register */
data[i] = devpriv->ao_readback[chan];
}
return i;
}
static int pcmda12_attach(struct comedi_device *dev,
struct comedi_devconfig *it)
{
const struct pcmda12_board *board = comedi_board(dev);
struct comedi_subdevice *s;
unsigned long iobase;
int ret;
iobase = it->options[0];
printk(KERN_INFO
"comedi%d: %s: io: %lx %s ", dev->minor, dev->driver->driver_name,
iobase, it->options[1] ? "simultaneous xfer mode enabled" : "");
if (!request_region(iobase, IOSIZE, dev->driver->driver_name)) {
printk("I/O port conflict\n");
return -EIO;
}
dev->iobase = iobase;
dev->board_name = board->name;
/*
* Allocate the private structure area. alloc_private() is a
* convenient macro defined in comedidev.h.
*/
if (alloc_private(dev, sizeof(struct pcmda12_private)) < 0) {
printk(KERN_ERR "cannot allocate private data structure\n");
return -ENOMEM;
}
devpriv->simultaneous_xfer_mode = it->options[1];
ret = comedi_alloc_subdevices(dev, 1);
if (ret)
return ret;
s = dev->subdevices;
s->private = NULL;
s->maxdata = (0x1 << BITS) - 1;
s->range_table = &pcmda12_ranges;
s->type = COMEDI_SUBD_AO;
s->subdev_flags = SDF_READABLE | SDF_WRITABLE;
s->n_chan = CHANS;
s->insn_write = &ao_winsn;
s->insn_read = &ao_rinsn;
zero_chans(dev); /* clear out all the registers, basically */
printk(KERN_INFO "attached\n");
return 1;
}
static void pcmda12_detach(struct comedi_device *dev)
{
if (dev->iobase)
release_region(dev->iobase, IOSIZE);
}
static const struct pcmda12_board pcmda12_boards[] = {
{
.name = "pcmda12",
},
};
static struct comedi_driver pcmda12_driver = {
.driver_name = "pcmda12",
.module = THIS_MODULE,
.attach = pcmda12_attach,
.detach = pcmda12_detach,
.board_name = &pcmda12_boards[0].name,
.offset = sizeof(struct pcmda12_board),
.num_names = ARRAY_SIZE(pcmda12_boards),
};
module_comedi_driver(pcmda12_driver);
MODULE_AUTHOR("Comedi http://www.comedi.org");
MODULE_DESCRIPTION("Comedi low-level driver");
MODULE_LICENSE("GPL");
|
