summaryrefslogtreecommitdiffstats
path: root/drivers/ide/trm290.c
blob: 75ea6152656663b6673c536e7903e4d2eb6bafda (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
/*
 *  Copyright (c) 1997-1998  Mark Lord
 *  Copyright (c) 2007       MontaVista Software, Inc. <source@mvista.com>
 *
 *  May be copied or modified under the terms of the GNU General Public License
 *
 *  June 22, 2004 - get rid of check_region
 *                   - Jesper Juhl
 *
 */

/*
 * This module provides support for the bus-master IDE DMA function
 * of the Tekram TRM290 chip, used on a variety of PCI IDE add-on boards,
 * including a "Precision Instruments" board.  The TRM290 pre-dates
 * the sff-8038 standard (ide-dma.c) by a few months, and differs
 * significantly enough to warrant separate routines for some functions,
 * while re-using others from ide-dma.c.
 *
 * EXPERIMENTAL!  It works for me (a sample of one).
 *
 * Works reliably for me in DMA mode (READs only),
 * DMA WRITEs are disabled by default (see #define below);
 *
 * DMA is not enabled automatically for this chipset,
 * but can be turned on manually (with "hdparm -d1") at run time.
 *
 * I need volunteers with "spare" drives for further testing
 * and development, and maybe to help figure out the peculiarities.
 * Even knowing the registers (below), some things behave strangely.
 */

#define TRM290_NO_DMA_WRITES	/* DMA writes seem unreliable sometimes */

/*
 * TRM-290 PCI-IDE2 Bus Master Chip
 * ================================
 * The configuration registers are addressed in normal I/O port space
 * and are used as follows:
 *
 * trm290_base depends on jumper settings, and is probed for by ide-dma.c
 *
 * trm290_base+2 when WRITTEN: chiptest register (byte, write-only)
 *	bit7 must always be written as "1"
 *	bits6-2 undefined
 *	bit1 1=legacy_compatible_mode, 0=native_pci_mode
 *	bit0 1=test_mode, 0=normal(default)
 *
 * trm290_base+2 when READ: status register (byte, read-only)
 *	bits7-2 undefined
 *	bit1 channel0 busmaster interrupt status 0=none, 1=asserted
 *	bit0 channel0 interrupt status 0=none, 1=asserted
 *
 * trm290_base+3 Interrupt mask register
 *	bits7-5 undefined
 *	bit4 legacy_header: 1=present, 0=absent
 *	bit3 channel1 busmaster interrupt status 0=none, 1=asserted (read only)
 *	bit2 channel1 interrupt status 0=none, 1=asserted (read only)
 *	bit1 channel1 interrupt mask: 1=masked, 0=unmasked(default)
 *	bit0 channel0 interrupt mask: 1=masked, 0=unmasked(default)
 *
 * trm290_base+1 "CPR" Config Pointer Register (byte)
 *	bit7 1=autoincrement CPR bits 2-0 after each access of CDR
 *	bit6 1=min. 1 wait-state posted write cycle (default), 0=0 wait-state
 *	bit5 0=enabled master burst access (default), 1=disable  (write only)
 *	bit4 PCI DEVSEL# timing select: 1=medium(default), 0=fast
 *	bit3 0=primary IDE channel, 1=secondary IDE channel
 *	bits2-0 register index for accesses through CDR port
 *
 * trm290_base+0 "CDR" Config Data Register (word)
 *	two sets of seven config registers,
 *	selected by CPR bit 3 (channel) and CPR bits 2-0 (index 0 to 6),
 *	each index defined below:
 *
 * Index-0 Base address register for command block (word)
 *	defaults: 0x1f0 for primary, 0x170 for secondary
 *
 * Index-1 general config register (byte)
 *	bit7 1=DMA enable, 0=DMA disable
 *	bit6 1=activate IDE_RESET, 0=no action (default)
 *	bit5 1=enable IORDY, 0=disable IORDY (default)
 *	bit4 0=16-bit data port(default), 1=8-bit (XT) data port
 *	bit3 interrupt polarity: 1=active_low, 0=active_high(default)
 *	bit2 power-saving-mode(?): 1=enable, 0=disable(default) (write only)
 *	bit1 bus_master_mode(?): 1=enable, 0=disable(default)
 *	bit0 enable_io_ports: 1=enable(default), 0=disable
 *
 * Index-2 read-ahead counter preload bits 0-7 (byte, write only)
 *	bits7-0 bits7-0 of readahead count
 *
 * Index-3 read-ahead config register (byte, write only)
 *	bit7 1=enable_readahead, 0=disable_readahead(default)
 *	bit6 1=clear_FIFO, 0=no_action
 *	bit5 undefined
 *	bit4 mode4 timing control: 1=enable, 0=disable(default)
 *	bit3 undefined
 *	bit2 undefined
 *	bits1-0 bits9-8 of read-ahead count
 *
 * Index-4 base address register for control block (word)
 *	defaults: 0x3f6 for primary, 0x376 for secondary
 *
 * Index-5 data port timings (shared by both drives) (byte)
 *	standard PCI "clk" (clock) counts, default value = 0xf5
 *
 *	bits7-6 setup time:  00=1clk, 01=2clk, 10=3clk, 11=4clk
 *	bits5-3 hold time:	000=1clk, 001=2clk, 010=3clk,
 *				011=4clk, 100=5clk, 101=6clk,
 *				110=8clk, 111=12clk
 *	bits2-0 active time:	000=2clk, 001=3clk, 010=4clk,
 *				011=5clk, 100=6clk, 101=8clk,
 *				110=12clk, 111=16clk
 *
 * Index-6 command/control port timings (shared by both drives) (byte)
 *	same layout as Index-5, default value = 0xde
 *
 * Suggested CDR programming for PIO mode0 (600ns):
 *	0x01f0,0x21,0xff,0x80,0x03f6,0xf5,0xde	; primary
 *	0x0170,0x21,0xff,0x80,0x0376,0xf5,0xde	; secondary
 *
 * Suggested CDR programming for PIO mode3 (180ns):
 *	0x01f0,0x21,0xff,0x80,0x03f6,0x09,0xde	; primary
 *	0x0170,0x21,0xff,0x80,0x0376,0x09,0xde	; secondary
 *
 * Suggested CDR programming for PIO mode4 (120ns):
 *	0x01f0,0x21,0xff,0x80,0x03f6,0x00,0xde	; primary
 *	0x0170,0x21,0xff,0x80,0x0376,0x00,0xde	; secondary
 *
 */

#include <linux/types.h>
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/ioport.h>
#include <linux/interrupt.h>
#include <linux/blkdev.h>
#include <linux/init.h>
#include <linux/pci.h>
#include <linux/ide.h>

#include <asm/io.h>

#define DRV_NAME "trm290"

static void trm290_prepare_drive (ide_drive_t *drive, unsigned int use_dma)
{
	ide_hwif_t *hwif = HWIF(drive);
	u16 reg = 0;
	unsigned long flags;

	/* select PIO or DMA */
	reg = use_dma ? (0x21 | 0x82) : (0x21 & ~0x82);

	local_irq_save(flags);

	if (reg != hwif->select_data) {
		hwif->select_data = reg;
		/* set PIO/DMA */
		outb(0x51 | (hwif->channel << 3), hwif->config_data + 1);
		outw(reg & 0xff, hwif->config_data);
	}

	/* enable IRQ if not probing */
	if (drive->dev_flags & IDE_DFLAG_PRESENT) {
		reg = inw(hwif->config_data + 3);
		reg &= 0x13;
		reg &= ~(1 << hwif->channel);
		outw(reg, hwif->config_data + 3);
	}

	local_irq_restore(flags);
}

static void trm290_selectproc (ide_drive_t *drive)
{
	trm290_prepare_drive(drive, !!(drive->dev_flags & IDE_DFLAG_USING_DMA));
}

static void trm290_dma_exec_cmd(ide_drive_t *drive, u8 command)
{
	ide_execute_command(drive, command, &ide_dma_intr, WAIT_CMD, NULL);
}

static int trm290_dma_setup(ide_drive_t *drive)
{
	ide_hwif_t *hwif = drive->hwif;
	struct request *rq = hwif->hwgroup->rq;
	unsigned int count, rw;

	if (rq_data_dir(rq)) {
#ifdef TRM290_NO_DMA_WRITES
		/* always use PIO for writes */
		trm290_prepare_drive(drive, 0);	/* select PIO xfer */
		return 1;
#endif
		rw = 1;
	} else
		rw = 2;

	if (!(count = ide_build_dmatable(drive, rq))) {
		/* try PIO instead of DMA */
		trm290_prepare_drive(drive, 0); /* select PIO xfer */
		return 1;
	}
	/* select DMA xfer */
	trm290_prepare_drive(drive, 1);
	outl(hwif->dmatable_dma | rw, hwif->dma_base);
	drive->waiting_for_dma = 1;
	/* start DMA */
	outw(count * 2 - 1, hwif->dma_base + 2);
	return 0;
}

static void trm290_dma_start(ide_drive_t *drive)
{
}

static int trm290_dma_end(ide_drive_t *drive)
{
	u16 status;

	drive->waiting_for_dma = 0;
	/* purge DMA mappings */
	ide_destroy_dmatable(drive);
	status = inw(HWIF(drive)->dma_base + 2);
	return status != 0x00ff;
}

static int trm290_dma_test_irq(ide_drive_t *drive)
{
	u16 status;

	status = inw(HWIF(drive)->dma_base + 2);
	return status == 0x00ff;
}

static void trm290_dma_host_set(ide_drive_t *drive, int on)
{
}

static void __devinit init_hwif_trm290(ide_hwif_t *hwif)
{
	struct pci_dev *dev	= to_pci_dev(hwif->dev);
	unsigned int  cfg_base	= pci_resource_start(dev, 4);
	unsigned long flags;
	u8 reg = 0;

	if ((dev->class & 5) && cfg_base)
		printk(KERN_INFO DRV_NAME " %s: chip", pci_name(dev));
	else {
		cfg_base = 0x3df0;
		printk(KERN_INFO DRV_NAME " %s: using default", pci_name(dev));
	}
	printk(KERN_CONT " config base at 0x%04x\n", cfg_base);
	hwif->config_data = cfg_base;
	hwif->dma_base = (cfg_base + 4) ^ (hwif->channel ? 0x80 : 0);

	printk(KERN_INFO "    %s: BM-DMA at 0x%04lx-0x%04lx\n",
	       hwif->name, hwif->dma_base, hwif->dma_base + 3);

	if (ide_allocate_dma_engine(hwif))
		return;

	local_irq_save(flags);
	/* put config reg into first byte of hwif->select_data */
	outb(0x51 | (hwif->channel << 3), hwif->config_data + 1);
	/* select PIO as default */
	hwif->select_data = 0x21;
	outb(hwif->select_data, hwif->config_data);
	/* get IRQ info */
	reg = inb(hwif->config_data + 3);
	/* mask IRQs for both ports */
	reg = (reg & 0x10) | 0x03;
	outb(reg, hwif->config_data + 3);
	local_irq_restore(flags);

	if (reg & 0x10)
		/* legacy mode */
		hwif->irq = hwif->channel ? 15 : 14;
	else if (!hwif->irq && hwif->mate && hwif->mate->irq)
		/* sharing IRQ with mate */
		hwif->irq = hwif->mate->irq;

#if 1
	{
	/*
	 * My trm290-based card doesn't seem to work with all possible values
	 * for the control basereg, so this kludge ensures that we use only
	 * values that are known to work.  Ugh.		-ml
	 */
		u16 new, old, compat = hwif->channel ? 0x374 : 0x3f4;
		static u16 next_offset = 0;
		u8 old_mask;

		outb(0x54 | (hwif->channel << 3), hwif->config_data + 1);
		old = inw(hwif->config_data);
		old &= ~1;
		old_mask = inb(old + 2);
		if (old != compat && old_mask == 0xff) {
			/* leave lower 10 bits untouched */
			compat += (next_offset += 0x400);
			hwif->io_ports.ctl_addr = compat + 2;
			outw(compat | 1, hwif->config_data);
			new = inw(hwif->config_data);
			printk(KERN_INFO "%s: control basereg workaround: "
				"old=0x%04x, new=0x%04x\n",
				hwif->name, old, new & ~1);
		}
	}
#endif
}

static const struct ide_port_ops trm290_port_ops = {
	.selectproc		= trm290_selectproc,
};

static struct ide_dma_ops trm290_dma_ops = {
	.dma_host_set		= trm290_dma_host_set,
	.dma_setup 		= trm290_dma_setup,
	.dma_exec_cmd		= trm290_dma_exec_cmd,
	.dma_start 		= trm290_dma_start,
	.dma_end		= trm290_dma_end,
	.dma_test_irq		= trm290_dma_test_irq,
	.dma_lost_irq		= ide_dma_lost_irq,
	.dma_timeout		= ide_dma_timeout,
};

static const struct ide_port_info trm290_chipset __devinitdata = {
	.name		= DRV_NAME,
	.init_hwif	= init_hwif_trm290,
	.chipset	= ide_trm290,
	.port_ops	= &trm290_port_ops,
	.dma_ops	= &trm290_dma_ops,
	.host_flags	= IDE_HFLAG_NO_ATAPI_DMA |
#if 0 /* play it safe for now */
			  IDE_HFLAG_TRUST_BIOS_FOR_DMA |
#endif
			  IDE_HFLAG_NO_AUTODMA |
			  IDE_HFLAG_NO_LBA48,
};

static int __devinit trm290_init_one(struct pci_dev *dev, const struct pci_device_id *id)
{
	return ide_pci_init_one(dev, &trm290_chipset, NULL);
}

static const struct pci_device_id trm290_pci_tbl[] = {
	{ PCI_VDEVICE(TEKRAM, PCI_DEVICE_ID_TEKRAM_DC290), 0 },
	{ 0, },
};
MODULE_DEVICE_TABLE(pci, trm290_pci_tbl);

static struct pci_driver trm290_pci_driver = {
	.name		= "TRM290_IDE",
	.id_table	= trm290_pci_tbl,
	.probe		= trm290_init_one,
	.remove		= ide_pci_remove,
};

static int __init trm290_ide_init(void)
{
	return ide_pci_register_driver(&trm290_pci_driver);
}

static void __exit trm290_ide_exit(void)
{
	pci_unregister_driver(&trm290_pci_driver);
}

module_init(trm290_ide_init);
module_exit(trm290_ide_exit);

MODULE_AUTHOR("Mark Lord");
MODULE_DESCRIPTION("PCI driver module for Tekram TRM290 IDE");
MODULE_LICENSE("GPL");