| Age | Commit message (Collapse) | Author |
|---|
|
When GRE support was added in linux-3.14, CHECKSUM_COMPLETE handling
broke on GRE+IPv6 because we did not update/use the appropriate csum :
GRO layer is supposed to use/update NAPI_GRO_CB(skb)->csum instead of
skb->csum
Tested using a GRE tunnel and IPv6 traffic. GRO aggregation now happens
at the first level (ethernet device) instead of being done in gre
tunnel. Native IPv6+TCP is still properly aggregated.
Fixes: bf5a755f5e918 ("net-gre-gro: Add GRE support to the GRO stack")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jerry Chu <hkchu@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, "ip -6 route get mark xyz" ignores the mark passed in
by userspace. Make it honour the mark, just like IPv4 does.
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
RFC 4861 states in 7.2.5:
The IsRouter flag in the cache entry MUST be set based on the
Router flag in the received advertisement. In those cases
where the IsRouter flag changes from TRUE to FALSE as a result
of this update, the node MUST remove that router from the
Default Router List and update the Destination Cache entries
for all destinations using that neighbor as a router as
specified in Section 7.3.3. This is needed to detect when a
node that is used as a router stops forwarding packets due to
being configured as a host.
Currently, when dealing with NA Message which IsRouter flag changes from
TRUE to FALSE, the kernel only removes router from the Default Router List,
and don't update the Destination Cache entries.
Now in order to update those Destination Cache entries, i introduce
function rt6_clean_tohost().
Signed-off-by: Duan Jiong <duanj.fnst@cn.fujitsu.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec
Conflicts:
net/ipv4/ip_vti.c
Steffen Klassert says:
====================
pull request (net): ipsec 2014-05-15
This pull request has a merge conflict in net/ipv4/ip_vti.c
between commit 8d89dcdf80d8 ("vti: don't allow to add the same
tunnel twice") and commit a32452366b72 ("vti4:Don't count header
length twice"). It can be solved like it is done in linux-next.
1) Fix a ipv6 xfrm output crash when a packet is rerouted
by netfilter to not use IPsec.
2) vti4 counts some header lengths twice leading to an incorrect
device mtu. Fix this by counting these headers only once.
3) We don't catch the case if an unsupported protocol is submitted
to the xfrm protocol handlers, this can lead to NULL pointer
dereferences. Fix this by adding the appropriate checks.
4) vti6 may unregister pernet ops twice on init errors.
Fix this by removing one of the calls to do it only once.
From Mathias Krause.
5) Set the vti tunnel mark before doing a lookup in the error
handlers. Otherwise we don't find the correct xfrm state.
====================
The conflict in ip_vti.c was simple, 'net' had a commit
removing a line from vti_tunnel_init() and this tree
being merged had a commit adding a line to the same
location.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
tot_len does specify the size of struct ipv6_txoptions. We need opt_flen +
opt_nflen to calculate the overall length of additional ipv6 extensions.
I found this while auditing the ipv6 output path for a memory corruption
reported by Alexey Preobrazhensky while he fuzzed an instrumented
AddressSanitizer kernel with trinity. This may or may not be the cause
of the original bug.
Fixes: 4df98e76cde7c6 ("ipv6: pmtudisc setting not respected with UFO/CORK")
Reported-by: Alexey Preobrazhensky <preobr@google.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The function ip6_tnl_validate assumes that the rtnl
attribute IFLA_IPTUN_PROTO always be filled . If this
attribute is not filled by the userspace application
kernel get crashed with NULL pointer dereference. This
patch fixes the potential kernel crash when
IFLA_IPTUN_PROTO is missing .
Signed-off-by: Susant Sahani <susant@redhat.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We need to use the mark we get from the tunnels o_key to
lookup the right vti state in the error handlers. This patch
ensures that.
Fixes: df3893c1 ("vti: Update the ipv4 side to use it's own receive hook.")
Fixes: fa9ad96d ("vti6: Update the ipv6 side to use its own receive hook.")
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
|
|
If we fail to register one of the xfrm protocol handlers we will
unregister the pernet ops twice on the error exit path. This will
probably lead to a kernel panic as the double deregistration
leads to a double kfree().
Fix this by removing one of the calls to do it only once.
Fixes: fa9ad96d49 ("vti6: Update the ipv6 side to use its own...")
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
|
|
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following batch contains netfilter fixes for your net tree, they are:
1) Fix use after free in nfnetlink when sending a batch for some
unsupported subsystem, from Denys Fedoryshchenko.
2) Skip autoload of the nat module if no binding is specified via
ctnetlink, from Florian Westphal.
3) Set local_df after netfilter defragmentation to avoid a bogus ICMP
fragmentation needed in the forwarding path, also from Florian.
4) Fix potential user after free in ip6_route_me_harder() when returning
the error code to the upper layers, from Sergey Popovich.
5) Skip possible bogus ICMP time exceeded emitted from the router (not
valid according to RFC) if conntrack zones are used, from Vasily Averin.
6) Fix fragment handling when nf_defrag_ipv4 is loaded but nf_conntrack
is not present, also from Vasily.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Dst is released one line before we access it again with dst->error.
Fixes: 58e35d147128 netfilter: ipv6: propagate routing errors from
ip6_route_me_harder()
Signed-off-by: Sergey Popovich <popovich_sergei@mail.ru>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
If conntrack defragments incoming ipv6 frags it stores largest original
frag size in ip6cb and sets ->local_df.
We must thus first test the largest original frag size vs. mtu, and not
vice versa.
Without this patch PKTTOOBIG is still generated in ip6_fragment() later
in the stack, but
1) IPSTATS_MIB_INTOOBIGERRORS won't increment
2) packet did (needlessly) traverse netfilter postrouting hook.
Fixes: fe6cc55f3a9 ("net: ip, ipv6: handle gso skbs in forwarding path")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We don't catch the case if an unsupported protocol is submitted
to the xfrm6 protocol handlers, this can lead to NULL pointer
dereferences. Fix this by adding the appropriate checks.
Fixes: 7e14ea15 ("xfrm6: Add IPsec protocol multiplexer")
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
|
|
To properly match iif in ip rules we have to provide
LOOPBACK_IFINDEX in flowi6_iif, not 0. Some ip6mr_fib_lookup
and fib6_rule_lookup callers need such fix.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the ipv6 fib changes during a table dump, the walk is
restarted and the number of nodes dumped are skipped. But the existing
code doesn't advance to the next node after a node is skipped. This can
cause the dump to loop or produce lots of duplicates when the fib
is modified during the dump.
This change advances the walk to the next node if the current node is
skipped after a restart.
Signed-off-by: Kumar Sundararajan <kumar@fb.com>
Signed-off-by: Chris Mason <clm@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Because the netdevice may be in another netns than the i/o netns, we should
use the i/o netns instead of dev_net(dev).
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Because the netdevice may be in another netns than the i/o netns, we should
use the i/o netns instead of dev_net(dev).
Note that netdev_priv(dev) cannot bu NULL, hence we can remove these useless
checks.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As suggested by Julian:
Simply, flowi4_iif must not contain 0, it does not
look logical to ignore all ip rules with specified iif.
because in fib_rule_match() we do:
if (rule->iifindex && (rule->iifindex != fl->flowi_iif))
goto out;
flowi4_iif should be LOOPBACK_IFINDEX by default.
We need to move LOOPBACK_IFINDEX to include/net/flow.h:
1) It is mostly used by flowi_iif
2) Fix the following compile error if we use it in flow.h
by the patches latter:
In file included from include/linux/netfilter.h:277:0,
from include/net/netns/netfilter.h:5,
from include/net/net_namespace.h:21,
from include/linux/netdevice.h:43,
from include/linux/icmpv6.h:12,
from include/linux/ipv6.h:61,
from include/net/ipv6.h:16,
from include/linux/sunrpc/clnt.h:27,
from include/linux/nfs_fs.h:30,
from init/do_mounts.c:32:
include/net/flow.h: In function ‘flowi4_init_output’:
include/net/flow.h:84:32: error: ‘LOOPBACK_IFINDEX’ undeclared (first use in this function)
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Julian Anastasov <ja@ssi.bg>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It's possible to remove the FB tunnel with the command 'ip link del ip6gre0' but
this is unsafe, the module always supposes that this device exists. For example,
ip6gre_tunnel_lookup() may use it unconditionally.
Let's add a rtnl handler for dellink, which will never remove the FB tunnel (we
let ip6gre_destroy_tunnels() do the job).
Introduced by commit c12b395a4664 ("gre: Support GRE over IPv6").
CC: Dmitry Kozlov <xeb@mail.ru>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the dst->output() path for ipv4, the code assumes the skb it has to
transmit is attached to an inet socket, specifically via
ip_mc_output() : The sk_mc_loop() test triggers a WARN_ON() when the
provider of the packet is an AF_PACKET socket.
The dst->output() method gets an additional 'struct sock *sk'
parameter. This needs a cascade of changes so that this parameter can
be propagated from vxlan to final consumer.
Fixes: 8f646c922d55 ("vxlan: keep original skb ownership")
Reported-by: lucien xin <lucien.xin@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ip_queue_xmit() assumes the skb it has to transmit is attached to an
inet socket. Commit 31c70d5956fc ("l2tp: keep original skb ownership")
changed l2tp to not change skb ownership and thus broke this assumption.
One fix is to add a new 'struct sock *sk' parameter to ip_queue_xmit(),
so that we do not assume skb->sk points to the socket used by l2tp
tunnel.
Fixes: 31c70d5956fc ("l2tp: keep original skb ownership")
Reported-by: Zhan Jianyu <nasa4836@gmail.com>
Tested-by: Zhan Jianyu <nasa4836@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Francois reported that setting big mtu on loopback device could prevent
tcp sessions making progress.
We do not support (yet ?) IPv6 Jumbograms and cook corrupted packets.
We must limit the IPv6 MTU to (65535 + 40) bytes in theory.
Tested:
ifconfig lo mtu 70000
netperf -H ::1
Before patch : Throughput : 0.05 Mbits
After patch : Throughput : 35484 Mbits
Reported-by: Francois WELLENREITER <f.wellenreiter@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
net-next commit 9c76a11, ipv6: tcp_ipv6 policy route issue, had
a boolean logic error that caused incorrect behaviour for TCP
SYN+ACK when oif-based rules are in use. Specifically:
1. If a SYN comes in from a global address, and sk_bound_dev_if
is not set, the routing lookup has oif set to the interface
the SYN came in on. Instead, it should have oif unset,
because for global addresses, the incoming interface doesn't
necessarily have any bearing on the interface the SYN+ACK is
sent out on.
2. If a SYN comes in from a link-local address, and
sk_bound_dev_if is set, the routing lookup has oif set to the
interface the SYN came in on. Instead, it should have oif set
to sk_bound_dev_if, because that's what the application
requested.
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ipv6 xfrm output path is not aware that packets can be
rerouted by NAT to not use IPsec. We crash in this case
because we expect to have a xfrm state at the dst_entry.
This crash happens if the ipv6 layer does IPsec and NAT
or if we have an interfamily IPsec tunnel with ipv4 NAT.
We fix this by checking for a NAT rerouted packet in each
address family and dst_output() to the new destination
in this case.
Reported-by: Martin Pelikan <martin.pelikan@gmail.com>
Tested-by: Martin Pelikan <martin.pelikan@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
|
|
All xtables variants suffer from the defect that the copy_to_user()
to copy the counters to user memory may fail after the table has
already been exchanged and thus exposed. Return an error at this
point will result in freeing the already exposed table. Any
subsequent packet processing will result in a kernel panic.
We can't copy the counters before exposing the new tables as we
want provide the counter state after the old table has been
unhooked. Therefore convert this into a silent error.
Cc: Florian Westphal <fw@strlen.de>
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
After commit c15b1ccadb323ea ("ipv6: move DAD and addrconf_verify
processing to workqueue") some counters are now updated in process context
and thus need to disable bh before doing so, otherwise deadlocks can
happen on 32-bit archs. Fabio Estevam noticed this while while mounting
a NFS volume on an ARM board.
As a compensation for missing this I looked after the other *_STATS_BH
and found three other calls which need updating:
1) icmp6_send: ip6_fragment -> icmpv6_send -> icmp6_send (error handling)
2) ip6_push_pending_frames: rawv6_sendmsg -> rawv6_push_pending_frames -> ...
(only in case of icmp protocol with raw sockets in error handling)
3) ping6_v6_sendmsg (error handling)
Fixes: c15b1ccadb323ea ("ipv6: move DAD and addrconf_verify processing to workqueue")
Reported-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
First off, we don't need to check for non-NULL rt any more, as we are
guaranteed to always get a valid rt6_info. Drop the check.
In case we couldn't allocate an inet_peer for fragmentation information
we currently generate strictly incrementing fragmentation ids for all
destination. This is done to maximize the cycle and avoid collisions.
Those fragmentation ids are very predictable. At least we should try to
mix in the destination address.
While it should make no difference to simply use a PRNG at this point,
secure_ipv6_id ensures that we don't leak information from prandom,
so its internal state could be recoverable.
This fallback function should normally not get used thus this should
not affect performance at all. It is just meant as a safety net.
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The issue raises when adding policy route, specify a particular
NIC as oif, the policy route did not take effect. The reason is
that fl6.oif is not set and route map failed. From the
tcp_v6_send_response function, if the binding address is linklocal,
fl6.oif is set, but not for global address.
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Wang Yufen <wangyufen@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move the whole rt6_need_strict as static inline into ip6_route.h,
so that it can be reused
Signed-off-by: Wang Yufen <wangyufen@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Wang Yufen <wangyufen@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
drivers/net/ethernet/marvell/mvneta.c
The mvneta.c conflict is a case of overlapping changes,
a conversion to devm_ioremap_resource() vs. a conversion
to netdev_alloc_pcpu_stats.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ERROR: "(foo*)" should be "(foo *)"
ERROR: "foo * bar" should be "foo *bar"
Suggested-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Wang Yufen <wangyufen@huawei.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ERROR: open brace '{' following enum go on the same line
ERROR: open brace '{' following struct go on the same line
ERROR: trailing statements should be on next line
Signed-off-by: Wang Yufen <wangyufen@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
WARNING: please, no space before tabs
WARNING: please, no spaces at the start of a line
ERROR: spaces required around that ':' (ctx:VxW)
ERROR: spaces required around that '>' (ctx:VxV)
ERROR: spaces required around that '>=' (ctx:VxV)
Signed-off-by: Wang Yufen <wangyufen@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
addrconf_join_solict and addrconf_join_anycast may cause actions which
need rtnl locked, especially on first address creation.
A new DAD state is introduced which defers processing of the initial
DAD processing into a workqueue.
To get rtnl lock we need to push the code paths which depend on those
calls up to workqueues, specifically addrconf_verify and the DAD
processing.
(v2)
addrconf_dad_failure needs to be queued up to the workqueue, too. This
patch introduces a new DAD state and stop the DAD processing in the
workqueue (this is because of the possible ipv6_del_addr processing
which removes the solicited multicast address from the device).
addrconf_verify_lock is removed, too. After the transition it is not
needed any more.
As we are not processing in bottom half anymore we need to be a bit more
careful about disabling bottom half out when we lock spin_locks which are also
used in bh.
Relevant backtrace:
[ 541.030090] RTNL: assertion failed at net/core/dev.c (4496)
[ 541.031143] CPU: 0 PID: 0 Comm: swapper/0 Tainted: G O 3.10.33-1-amd64-vyatta #1
[ 541.031145] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2007
[ 541.031146] ffffffff8148a9f0 000000000000002f ffffffff813c98c1 ffff88007c4451f8
[ 541.031148] 0000000000000000 0000000000000000 ffffffff813d3540 ffff88007fc03d18
[ 541.031150] 0000880000000006 ffff88007c445000 ffffffffa0194160 0000000000000000
[ 541.031152] Call Trace:
[ 541.031153] <IRQ> [<ffffffff8148a9f0>] ? dump_stack+0xd/0x17
[ 541.031180] [<ffffffff813c98c1>] ? __dev_set_promiscuity+0x101/0x180
[ 541.031183] [<ffffffff813d3540>] ? __hw_addr_create_ex+0x60/0xc0
[ 541.031185] [<ffffffff813cfe1a>] ? __dev_set_rx_mode+0xaa/0xc0
[ 541.031189] [<ffffffff813d3a81>] ? __dev_mc_add+0x61/0x90
[ 541.031198] [<ffffffffa01dcf9c>] ? igmp6_group_added+0xfc/0x1a0 [ipv6]
[ 541.031208] [<ffffffff8111237b>] ? kmem_cache_alloc+0xcb/0xd0
[ 541.031212] [<ffffffffa01ddcd7>] ? ipv6_dev_mc_inc+0x267/0x300 [ipv6]
[ 541.031216] [<ffffffffa01c2fae>] ? addrconf_join_solict+0x2e/0x40 [ipv6]
[ 541.031219] [<ffffffffa01ba2e9>] ? ipv6_dev_ac_inc+0x159/0x1f0 [ipv6]
[ 541.031223] [<ffffffffa01c0772>] ? addrconf_join_anycast+0x92/0xa0 [ipv6]
[ 541.031226] [<ffffffffa01c311e>] ? __ipv6_ifa_notify+0x11e/0x1e0 [ipv6]
[ 541.031229] [<ffffffffa01c3213>] ? ipv6_ifa_notify+0x33/0x50 [ipv6]
[ 541.031233] [<ffffffffa01c36c8>] ? addrconf_dad_completed+0x28/0x100 [ipv6]
[ 541.031241] [<ffffffff81075c1d>] ? task_cputime+0x2d/0x50
[ 541.031244] [<ffffffffa01c38d6>] ? addrconf_dad_timer+0x136/0x150 [ipv6]
[ 541.031247] [<ffffffffa01c37a0>] ? addrconf_dad_completed+0x100/0x100 [ipv6]
[ 541.031255] [<ffffffff8105313a>] ? call_timer_fn.isra.22+0x2a/0x90
[ 541.031258] [<ffffffffa01c37a0>] ? addrconf_dad_completed+0x100/0x100 [ipv6]
Hunks and backtrace stolen from a patch by Stephen Hemminger.
Reported-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If an IPv6 host route with metrics exists, an attempt to add a
new route for the same target with different metrics fails but
rewrites the metrics anyway:
12sp0:~ # ip route add fec0::1 dev eth0 rto_min 1000
12sp0:~ # ip -6 route show
fe80::/64 dev eth0 proto kernel metric 256
fec0::1 dev eth0 metric 1024 rto_min lock 1s
12sp0:~ # ip route add fec0::1 dev eth0 rto_min 1500
RTNETLINK answers: File exists
12sp0:~ # ip -6 route show
fe80::/64 dev eth0 proto kernel metric 256
fec0::1 dev eth0 metric 1024 rto_min lock 1.5s
This is caused by all IPv6 host routes using the metrics in
their inetpeer (or the shared default). This also holds for the
new route created in ip6_route_add() which shares the metrics
with the already existing route and thus ip6_route_add()
rewrites the metrics even if the new route ends up not being
used at all.
Another problem is that old metrics in inetpeer can reappear
unexpectedly for a new route, e.g.
12sp0:~ # ip route add fec0::1 dev eth0 rto_min 1000
12sp0:~ # ip route del fec0::1
12sp0:~ # ip route add fec0::1 dev eth0
12sp0:~ # ip route change fec0::1 dev eth0 hoplimit 10
12sp0:~ # ip -6 route show
fe80::/64 dev eth0 proto kernel metric 256
fec0::1 dev eth0 metric 1024 hoplimit 10 rto_min lock 1s
Resolve the first problem by moving the setting of metrics down
into fib6_add_rt2node() to the point we are sure we are
inserting the new route into the tree. Second problem is
addressed by introducing new flag DST_METRICS_FORCE_OVERWRITE
which is set for a new host route in ip6_route_add() and makes
ipv6_cow_metrics() always overwrite the metrics in inetpeer
(even if they are not "new"); it is reset after that.
v5: use a flag in _metrics member rather than one in flags
v4: fix a typo making a condition always true (thanks to Hannes
Frederic Sowa)
v3: rewritten based on David Miller's idea to move setting the
metrics (and allocation in non-host case) down to the point we
already know the route is to be inserted. Also rebased to
net-next as it is quite late in the cycle.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
Documentation/devicetree/bindings/net/micrel-ks8851.txt
net/core/netpoll.c
The net/core/netpoll.c conflict is a bug fix in 'net' happening
to code which is completely removed in 'net-next'.
In micrel-ks8851.txt we simply have overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 812e44dd1829 ("ip6mr: advertise new mfc entries via rtnl") reuses the
function ip6mr_fill_mroute() to notify mfc events.
But this function was used only for dump and thus was always setting the
flag NLM_F_MULTI, which is wrong in case of a single notification.
Libraries like libnl will wait forever for NLMSG_DONE.
CC: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In ip6_append_data_mtu(), when the xfrm mode is not tunnel(such as
transport),the ipsec header need to be added in the first fragment, so the mtu
will decrease to reserve space for it, then the second fragment come, the mtu
should be turn back, as the commit 0c1833797a5a6ec23ea9261d979aa18078720b74
said. however, in the commit a493e60ac4bbe2e977e7129d6d8cbb0dd236be, it use
*mtu = min(*mtu, ...) to change the mtu, which lead to the new mtu is alway
equal with the first fragment's. and cannot turn back.
when I test through ping6 -c1 -s5000 $ip (mtu=1280):
...frag (0|1232) ESP(spi=0x00002000,seq=0xb), length 1232
...frag (1232|1216)
...frag (2448|1216)
...frag (3664|1216)
...frag (4880|164)
which should be:
...frag (0|1232) ESP(spi=0x00001000,seq=0x1), length 1232
...frag (1232|1232)
...frag (2464|1232)
...frag (3696|1232)
...frag (4928|116)
so delete the min() when change back the mtu.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Fixes: 75a493e60ac4bb ("ipv6: ip6_append_data_mtu did not care about pmtudisc and frag_size")
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec-next
Steffen Klassert says:
====================
One patch to rename a newly introduced struct. The rest is
the rework of the IPsec virtual tunnel interface for ipv6 to
support inter address family tunneling and namespace crossing.
1) Rename the newly introduced struct xfrm_filter to avoid a
conflict with iproute2. From Nicolas Dichtel.
2) Introduce xfrm_input_afinfo to access the address family
dependent tunnel callback functions properly.
3) Add and use a IPsec protocol multiplexer for ipv6.
4) Remove dst_entry caching. vti can lookup multiple different
dst entries, dependent of the configured xfrm states. Therefore
it does not make to cache a dst_entry.
5) Remove caching of flow informations. vti6 does not use the the
tunnel endpoint addresses to do route and xfrm lookups.
6) Update the vti6 to use its own receive hook.
7) Remove the now unused xfrm_tunnel_notifier. This was used from vti
and is replaced by the IPsec protocol multiplexer hooks.
8) Support inter address family tunneling for vti6.
9) Check if the tunnel endpoints of the xfrm state and the vti interface
are matching and return an error otherwise.
10) Enable namespace crossing for vti devices.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace the bh safe variant with the hard irq safe variant.
We need a hard irq safe variant to deal with netpoll transmitting
packets from hard irq context, and we need it in most if not all of
the places using the bh safe variant.
Except on 32bit uni-processor the code is exactly the same so don't
bother with a bh variant, just have a hard irq safe variant that
everyone can use.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
drivers/net/usb/r8152.c
drivers/net/xen-netback/netback.c
Both the r8152 and netback conflicts were simple overlapping
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
vti6 is now fully namespace aware, so allow namespace changing
for vti devices.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
|
|
The tunnel endpoints of the xfrm_state we got from the xfrm_lookup
must match the tunnel endpoints of the vti interface. This patch
ensures this matching.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
|
|
With this patch we can tunnel ipv4 traffic via a vti6
interface. A vti6 interface can now have an ipv4 address
and ipv4 traffic can be routed via a vti6 interface.
The resulting traffic is xfrm transformed and tunneled
through ipv6 if matching IPsec policies and states are
present.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
|
|
This was used from vti and is replaced by the IPsec protocol
multiplexer hooks. It is now unused, so remove it.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
|
|
With this patch, vti6 uses the IPsec protocol multiplexer to
register its own receive side hooks for ESP, AH and IPCOMP.
Vti6 now does the following on receive side:
1. Do an input policy check for the IPsec packet we received.
This is required because this packet could be already
prosecces by IPsec, so an inbuond policy check is needed.
2. Mark the packet with the i_key. The policy and the state
must match this key now. Policy and state belong to the vti
namespace and policy enforcement is done at the further layers.
3. Call the generic xfrm layer to do decryption and decapsulation.
4. Wait for a callback from the xfrm layer to properly clean the
skb to not leak informations on namespace transitions and
update the device statistics.
On transmit side:
1. Mark the packet with the o_key. The policy and the state
must match this key now.
2. Do a xfrm_lookup on the original packet with the mark applied.
3. Check if we got an IPsec route.
4. Clean the skb to not leak informations on namespace
transitions.
5. Attach the dst_enty we got from the xfrm_lookup to the skb.
6. Call dst_output to do the IPsec processing.
7. Do the device statistics.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
|
|
Unlike ip6_tunnel, vti6 does not use the the tunnel
endpoint addresses to do route and xfrm lookups.
So no need to cache the flow informations. It also
does not make sense to calculate the mtu based on
such flow informations, so remove this too.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
|
|
Unlike ip6_tunnel, vti6 can lookup multiple different dst entries,
dependent of the configured xfrm states. Therefore it does not make
sense to cache a dst_entry.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
|
|
Switch ipcomp6 to use the new IPsec protocol multiplexer.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
|
|
Switch ah6 to use the new IPsec protocol multiplexer.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
|
Eric Dumazet
Lorenzo Colitti
Duan Jiong
David S. Miller
Hannes Frederic Sowa
Susant Sahani
Steffen Klassert
Mathias Krause
Sergey Popovich
Florian Westphal
Julian Anastasov
Kumar Sundararajan
Nicolas Dichtel
Cong Wang
Thomas Graf
Wang Yufen
Michal Kubeček
lucien
Eric W. Biederman