| Age | Commit message (Collapse) | Author |
|---|
|
When firmware does not use _DSD properties that allow properly name GPIO
resources, the kernel falls back on parsing _CRS resources, and will
return entries described as GpioInt() as general purpose GPIOs even
though they are meant to be used simply as interrupt sources for the
device:
Device (ETSA)
{
Name (_HID, "ELAN0001")
...
Method(_CRS, 0x0, NotSerialized)
{
Name(BUF0,ResourceTemplate ()
{
I2CSerialBus(
0x10, /* SlaveAddress */
ControllerInitiated, /* SlaveMode */
400000, /* ConnectionSpeed */
AddressingMode7Bit, /* AddressingMode */
"\\_SB.I2C1", /* ResourceSource */
)
GpioInt (Edge, ActiveLow, ExclusiveAndWake, PullNone,,
"\\_SB.GPSW") { BOARD_TOUCH_GPIO_INDEX }
} )
Return (BUF0)
}
...
}
This gives troubles with drivers such as Elan Touchscreen driver
(elants_i2c) that uses devm_gpiod_get to look up "reset" GPIO line and
decide whether the driver is responsible for powering up and resetting
the device, or firmware is. In the above case the lookup succeeds, we
map GPIO as output and later fail to request client->irq interrupt that
is mapped to the same GPIO.
Let's ignore resources described as GpioInt() while parsing _CRS when
requesting output GPIOs (but allow them when requesting GPIOD_ASIS or
GPIOD_IN as some drivers, such as i2c-hid, do request GPIO as input and
then map it to interrupt with gpiod_to_irq).
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dtor@chromium.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
devm_kzalloc() returns NULL on failure.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
|
|
When section alignment padding is in effect we need to shift / truncate
the range that is queried for poison by the 'start_pad' or 'end_trunc'
reservations.
It's easiest if we just pass in an adjusted resource range rather than
deriving it from the passed in namespace. With the resource range
resolution pushed out to the caller we can also push the
namespace-to-region lookup to the caller and drop the implicit pmem-type
assumption about the passed in namespace object.
Cc: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
If we detect a namespace has a stale info block in the init path, we
should overwrite with the latest configuration. In fact, we already
return -ENODEV when the parent uuid is invalid, the same should be done
for the 'self' uuid. Otherwise we can get into a condition where
userspace is unable to reconfigure the pfn-device without directly /
manually invalidating the info block.
Cc: <stable@vger.kernel.org>
Reported-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
It appears that smart data retrieval has been broken the since the
initial implementation. Fix the payload size to be 128-bytes per the
specification.
Cc: <stable@vger.kernel.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
This reverts commit 0fd10721fe3664f7549e74af9d28a509c9a68719.
That patch causes the ib_srpt driver to crash as soon as the first SCSI
command is received:
kernel BUG at drivers/infiniband/ulp/srpt/ib_srpt.c:1439!
invalid opcode: 0000 [#1] SMP
Workqueue: target_completion target_complete_ok_work [target_core_mod]
RIP: srpt_queue_response+0x437/0x4a0 [ib_srpt]
Call Trace:
srpt_queue_data_in+0x9/0x10 [ib_srpt]
target_complete_ok_work+0x152/0x2b0 [target_core_mod]
process_one_work+0x197/0x480
worker_thread+0x49/0x490
kthread+0xea/0x100
ret_from_fork+0x22/0x40
Aside from the crash, the shortcomings of that patch are as follows:
- It makes the ib_srpt driver use I/O contexts allocated by
transport_alloc_session_tags() but it does not initialize these I/O
contexts properly. All the initializations performed by
srpt_alloc_ioctx() are skipped.
- It swaps the order of the send ioctx allocation and the transition to
RTR mode which is wrong.
- The amount of memory that is needed for I/O contexts is doubled.
- srpt_rdma_ch.free_list is no longer used but is not removed.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client
Pull Ceph fix from Sage Weil:
"This just fixes a few remaining memory allocations in RBD to use
GFP_NOIO instead of GFP_ATOMIC"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
rbd: use GFP_NOIO consistently for request allocations
|
|
Pull virtio/qemu fixes from Michael S Tsirkin:
"A couple of fixes for virtio and for the new QEMU fw cfg driver"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
virtio: add VIRTIO_CONFIG_S_NEEDS_RESET device status bit
MAINTAINERS: add entry for QEMU
firmware: qemu_fw_cfg.c: hold ACPI global lock during device access
virtio: virtio 1.0 cs04 spec compliance for reset
qemu_fw_cfg: don't leak kobj on init error
|
|
Pull drm fixes from Dave Airlie:
"This is mostly amdgpu/radeon fixes, and imx related fixes.
There is also one one TTM fix, one nouveau fix, and one hdlcd fix.
The AMD ones are some fixes for power management after suspend/resume
one some GPUs, and some vblank fixes.
The IMX ones are for more stricter plane checks and some cleanups.
I'm off until Monday, so therre might be some fixes early next week if
anyone missed me"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (34 commits)
drm/nouveau/tegra: acquire and enable reference clock if needed
drm/amdgpu: total vram size also reduces pin size
drm/amd/powerplay: add uvd/vce dpm enabling flag default.
drm/amd/powerplay: fix issue that resume back, dpm can't work on FIJI.
drm/amdgpu: save and restore the firwmware cache part when suspend resume
drm/amdgpu: save and restore UVD context with suspend and resume
drm/ttm: use phys_addr_t for ttm_bus_placement
drm: ARM HDLCD - fix an error code
drm: ARM HDLCD - get rid of devm_clk_put()
drm/radeon: Only call drm_vblank_on/off between drm_vblank_init/cleanup
drm/amdgpu: fence wait old rcu slot
drm/amdgpu: fix leaking fence in the pageflip code
drm/amdgpu: print vram type rather than just DDR
drm/amdgpu/gmc: use proper register for vram type on Fiji
drm/amdgpu/gmc: move vram type fetching into sw_init
drm/amdgpu: Set vblank_disable_allowed = true
drm/radeon: Set vblank_disable_allowed = true
drm/amd/powerplay: Need to change boot to performance state in resume.
drm/amd/powerplay: add new Fiji function for not setting same ps.
drm/amdgpu: check dpm state before pm system fs initialized.
...
|
|
Now wakeirq stops working for device if wakeup option for
this device will be reconfigured through sysfs, like:
echo disabled > /sys/devices/platform/extcon_usb1/power/wakeup
echo enabled > /sys/devices/platform/extcon_usb1/power/wakeup
Once above set of commands is executed the device's wakeup_source
opject will be recreated and dev->power.wakeup->wakeirq field will
contain NULL. As result, device_wakeup_arm_wake_irqs() will not arm
wakeirq for the affected device.
Hece, lets try to fix it in the following way:
check for dev->wakeirq field when device_wakeup_attach() is called
and if !NULL re-attach wakeirq to the device
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
KBL is similar to SKL
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
SKX is similar to BDX
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
This driver registers cpuidle devices when a CPU comes online, but it
leaves the registrations in place when a CPU goes offline. The module
exit code only unregisters the currently online CPUs, leaving the
devices for offline CPUs dangling.
This patch changes the driver to clean up all registrations on exit,
even those from CPUs that are offline.
Signed-off-by: Richard Cochran <rcochran@linutronix.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
If a cpuidle registration error occurs during the hot plug notifier
callback, we should really inform the hot plug machinery instead of
just ignoring the error. This patch changes the callback to properly
return on error.
Signed-off-by: Richard Cochran <rcochran@linutronix.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The helper function, intel_idle_cpu_init, registers one new device
with the cpuidle layer. If the registration should fail, that
function immediately calls intel_idle_cpuidle_devices_uninit() to
unregister every last CPU's device. However, it makes no sense to do
so, when called from the hot plug notifier callback.
This patch moves the call to intel_idle_cpuidle_devices_uninit()
outside of the helper function to the one call site that actually
needs to perform the de-registrations.
Signed-off-by: Richard Cochran <rcochran@linutronix.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
This driver sets the broadcast tick quite early on during probe and does
not clean up again in cast of failure. This patch moves the setup call
after the registration, placing the on_each_cpu() calls within the global
CPU lock region.
Signed-off-by: Richard Cochran <rcochran@linutronix.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The helper function, intel_idle_cpuidle_devices_uninit, frees the
globally allocated per-CPU data. However, this function is invoked
from the hot plug notifier callback at a time when freeing that data
is not safe.
If the call to cpuidle_register_driver() should fail (say, due to lack
of memory), then the driver will free its per-CPU region. On the
*next* CPU_ONLINE event, the driver will happily use the region again
and even free it again if the failure repeats.
This patch fixes the issue by moving the call to free_percpu() outside
of the helper function at the two call sites that actually need to
free the per-CPU data.
Signed-off-by: Richard Cochran <rcochran@linutronix.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
In the module_init() method, if the per-CPU allocation fails, then the
active cpuidle registration is not cleaned up. This patch fixes the
issue by attempting the allocation before registration, and then
cleaning it up again on registration failure.
Signed-off-by: Richard Cochran <rcochran@linutronix.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
In the module_exit() method, this driver first frees its per-CPU
pointer, then unregisters a callback making use of the pointer.
Furthermore, the function, intel_idle_cpuidle_devices_uninit, is racy
against CPU hot plugging as it calls for_each_online_cpu().
This patch corrects the issues by unregistering first on the exit path
while holding the hot plug lock.
Signed-off-by: Richard Cochran <rcochran@linutronix.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The function, intel_idle_cpuidle_driver_init, makes calls on each CPU
to auto_demotion_disable() and c1e_promotion_disable(). These calls
are redundant, as intel_idle_cpu_init() does the same calls just a bit
later on. They are also premature, as the driver registration may yet
fail.
This patch removes the redundant code.
Signed-off-by: Richard Cochran <rcochran@linutronix.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The function, intel_idle_cpuidle_driver_init, delivers no error codes
at all. This patch changes the function to return 'void' instead of
returning zero.
Signed-off-by: Richard Cochran <rcochran@linutronix.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Signed-off-by: Richard Cochran <rcochran@linutronix.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Make sure we don't OOPS in case clock-frequency is set to 0 in a DT. The
variable set here is later used as a divisor.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v4.6-rc3
We have two more fixes to f_midi. It should now
behave much better.
dwc3-keystone.c has gotten a fix which now allows it
to work on keystone device when running in
peripheral mode. A similar fix for DMA configuration
was made for udc-core, too.
We have a new PCI ID for Intel's Broxton
platform. DWC3 can run on those platforms as well.
And we also have some dwc2 got a fix for dr_mode
usage, while renesas controller got 3 important
fixes: a NULL pointer deref fix, IRQ <-> DMA race
fix, and a fix to prevent a situation where we would
queue a request to a disabled endpoint.
|
|
Signed-off-by: Junwei Zhang <Jerry.Zhang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
|
|
My static checker complains that "dma_alias" is uninitialized unless we
are dealing with a pci device. This is true but harmless. Anyway, we
can flip the condition around to silence the warning.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Since commit cd6438c5f844 ("iommu/rockchip: Reconstruct to support multi
slaves") rk_iommu_is_stall_active() always returns false because the
bitwise AND operates on the boolean flag promoted to an integer and a
value that is either zero or BIT(2).
Explicitly convert the right-hand value to a boolean so that both sides
are guaranteed to be either zero or one.
rk_iommu_is_paging_enabled() does not suffer from the same problem since
RK_MMU_STATUS_PAGING_ENABLED is BIT(0), but let's apply the same change
for consistency and to make it clear that it's correct without needing
to lookup the value.
Fixes: cd6438c5f844 ("iommu/rockchip: Reconstruct to support multi slaves")
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
IOMMU drivers that do not support default domains, but make
use of the the group->domain pointer can get that pointer
overwritten with NULL on device add/remove.
Make sure this can't happen by only overwriting the domain
pointer when it is NULL.
Cc: stable@vger.kernel.org # v4.4+
Fixes: 1228236de5f9 ('iommu: Move default domain allocation to iommu_group_get_for_dev()')
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Allowing for the future possibility of implementing AML-based
(i.e., firmware-triggered) access to the QEMU fw_cfg device,
acquire the global ACPI lock when accessing the device on behalf
of the guest-side sysfs driver, to prevent any potential race
conditions.
Suggested-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Gabriel Somlo <somlo@cmu.edu>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
The spec says: after writing 0 to device_status, the driver MUST wait
for a read of device_status to return 0 before reinitializing the
device.
Cc: stable@vger.kernel.org
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
|
|
If platform_driver_register fails, we should
cleanup fw_cfg_top_ko before exiting.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Gabriel Somlo <somlo@cmu.edu>
|
|
Thomas reports:
"Windows:
00 diagnostics
01 modem
02 at-port
03 nmea
04 nic
Linux:
T: Bus=02 Lev=01 Prnt=01 Port=03 Cnt=01 Dev#= 4 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=2001 ProdID=7e19 Rev=02.32
S: Manufacturer=Mobile Connect
S: Product=Mobile Connect
S: SerialNumber=0123456789ABCDEF
C: #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
I: If#= 5 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage"
Reported-by: Thomas Schäfer <tschaefer@t-online.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
The CP2105 is used in the GE Healthcare Remote Alarm Box, with the
Manufacturer ID of 0x1901 and Product ID of 0x0194.
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
A Fedora user reports that the ftdi_sio driver works properly for the
ICP DAS I-7561U device. Further, the user manual for these devices
instructs users to load the driver and add the ids using the sysfs
interface.
Add support for these in the driver directly so that the devices work
out of the box instead of needing manual configuration.
Reported-by: <thesource@mail.ru>
CC: stable <stable@vger.kernel.org>
Signed-off-by: Josh Boyer <jwboyer@fedoraproject.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
commit e2c8b8701e2d moved modeset locking inside resume/suspend
functions, but missed a code path only executed on lid close/open
on older hardware. The result was a deadlock when closing and
opening the lid without suspending on such hardware:
=============================================
[ INFO: possible recursive locking detected ]
4.6.0-rc1 #385 Not tainted
---------------------------------------------
kworker/0:3/88 is trying to acquire lock:
(&dev->mode_config.mutex){+.+.+.}, at: [<ffffffffa063e6a4>] intel_display_resume+0x4a/0x12f [i915]
but task is already holding lock:
(&dev->mode_config.mutex){+.+.+.}, at: [<ffffffffa02d0d4f>] drm_modeset_lock_all+0x3e/0xa6 [drm]
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&dev->mode_config.mutex);
lock(&dev->mode_config.mutex);
*** DEADLOCK ***
May be due to missing lock nesting notation
7 locks held by kworker/0:3/88:
#0: ("kacpi_notify"){++++.+}, at: [<ffffffff81068dfc>] process_one_work+0x14a/0x50b
#1: ((&dpc->work)#2){+.+.+.}, at: [<ffffffff81068dfc>] process_one_work+0x14a/0x50b
#2: ((acpi_lid_notifier).rwsem){++++.+}, at: [<ffffffff8106f874>] __blocking_notifier_call_chain+0x34/0x65
#3: (&dev_priv->modeset_restore_lock){+.+.+.}, at: [<ffffffffa0664cf6>] intel_lid_notify+0x3c/0xd9 [i915]
#4: (&dev->mode_config.mutex){+.+.+.}, at: [<ffffffffa02d0d4f>] drm_modeset_lock_all+0x3e/0xa6 [drm]
#5: (crtc_ww_class_acquire){+.+.+.}, at: [<ffffffffa02d0d59>] drm_modeset_lock_all+0x48/0xa6 [drm]
#6: (crtc_ww_class_mutex){+.+.+.}, at: [<ffffffffa02d0b2a>] modeset_lock+0x13c/0x1cd [drm]
stack backtrace:
CPU: 0 PID: 88 Comm: kworker/0:3 Not tainted 4.6.0-rc1 #385
Hardware name: LENOVO 2776LEG/2776LEG, BIOS 6EET55WW (3.15 ) 12/19/2011
Workqueue: kacpi_notify acpi_os_execute_deferred
0000000000000000 ffff88022fd5f990 ffffffff8124af06 ffffffff825b39c0
ffffffff825b39c0 ffff88022fd5fa60 ffffffff8108f547 ffff88022fd5fa70
000000008108e817 ffff880230236cc0 0000000000000000 ffffffff825b39c0
Call Trace:
[<ffffffff8124af06>] dump_stack+0x67/0x90
[<ffffffff8108f547>] __lock_acquire+0xdb5/0xf71
[<ffffffff8108bd2c>] ? look_up_lock_class+0xbe/0x10a
[<ffffffff8108fae2>] lock_acquire+0x137/0x1cb
[<ffffffff8108fae2>] ? lock_acquire+0x137/0x1cb
[<ffffffffa063e6a4>] ? intel_display_resume+0x4a/0x12f [i915]
[<ffffffff8148202f>] mutex_lock_nested+0x7e/0x3a4
[<ffffffffa063e6a4>] ? intel_display_resume+0x4a/0x12f [i915]
[<ffffffffa063e6a4>] ? intel_display_resume+0x4a/0x12f [i915]
[<ffffffffa02d0b2a>] ? modeset_lock+0x13c/0x1cd [drm]
[<ffffffffa063e6a4>] intel_display_resume+0x4a/0x12f [i915]
[<ffffffffa063e6a4>] ? intel_display_resume+0x4a/0x12f [i915]
[<ffffffffa02d0b2a>] ? modeset_lock+0x13c/0x1cd [drm]
[<ffffffffa02d0b2a>] ? modeset_lock+0x13c/0x1cd [drm]
[<ffffffffa02d0bf7>] ? drm_modeset_lock+0x17/0x24 [drm]
[<ffffffffa02d0c8b>] ? drm_modeset_lock_all_ctx+0x87/0xa1 [drm]
[<ffffffffa0664d6a>] intel_lid_notify+0xb0/0xd9 [i915]
[<ffffffff8106f4c6>] notifier_call_chain+0x4a/0x6c
[<ffffffff8106f88d>] __blocking_notifier_call_chain+0x4d/0x65
[<ffffffff8106f8b9>] blocking_notifier_call_chain+0x14/0x16
[<ffffffffa0011215>] acpi_lid_send_state+0x83/0xad [button]
[<ffffffffa00112a6>] acpi_button_notify+0x41/0x132 [button]
[<ffffffff812b07df>] acpi_device_notify+0x19/0x1b
[<ffffffff812c8570>] acpi_ev_notify_dispatch+0x49/0x64
[<ffffffff812ab9fb>] acpi_os_execute_deferred+0x14/0x20
[<ffffffff81068f17>] process_one_work+0x265/0x50b
[<ffffffff810696f5>] worker_thread+0x1fc/0x2dd
[<ffffffff810694f9>] ? rescuer_thread+0x309/0x309
[<ffffffff810694f9>] ? rescuer_thread+0x309/0x309
[<ffffffff8106e2d6>] kthread+0xe0/0xe8
[<ffffffff8107bc47>] ? local_clock+0x19/0x22
[<ffffffff81484f42>] ret_from_fork+0x22/0x40
[<ffffffff8106e1f6>] ? kthread_create_on_node+0x1b5/0x1b5
Fixes: e2c8b8701e2d ("drm/i915: Use atomic helpers for suspend, v2.")
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459328913-13719-1-git-send-email-bjorn@mork.no
(cherry picked from commit 9f54d4bd5808b5c892a44c539c126b71d299f341)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux into char-misc-linus
Kees briefly writes:
fixes some possible memory allocation leaks on error paths
|
|
The acpi_pcc_probe() may end up accessing memory outside of the PCCT
table space causing the kernel panic(). Increment the pcct_entry
pointer after parsing 'HW-reduced Communications Subspace' to fix
the problem. This change also enables the parsing of subtable at
index 0.
Signed-off-by: Shanker Donthineni <shankerd@codeaurora.org>
Acked-by: Ashwin Chaugule <ashwin.chaugule@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
This frees the allocated page if there is a kmalloc failure.
Signed-off-by: Kees Cook <keescook@chromium.org>
|
|
This case is supposed to read from a memory after it has been freed,
but we missed freeing base if the memory 'val' could not be allocated.
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Kees Cook <keescook@chromium.org>
|
|
This case is supposed to read from a page after after it is freed, but
it missed freeing val if we are not able to get a free page.
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Kees Cook <keescook@chromium.org>
|
|
into drm-fixes
Lots of misc bug fixes for radeon and amdgpu and one for ttm.
- fix vram info fetching on Fiji and unposted boards
- additional vblank fixes from the conversion to drm_vblank_on/off
- UVD dGPU suspend and resume fixes
- lots of powerplay fixes
- fix a fence leak in the pageflip code
- ttm fix for platforms where CPU is 32 bit, but physical addresses are >32bits
* 'drm-fixes-4.6' of git://people.freedesktop.org/~agd5f/linux: (21 commits)
drm/amdgpu: total vram size also reduces pin size
drm/amd/powerplay: add uvd/vce dpm enabling flag default.
drm/amd/powerplay: fix issue that resume back, dpm can't work on FIJI.
drm/amdgpu: save and restore the firwmware cache part when suspend resume
drm/amdgpu: save and restore UVD context with suspend and resume
drm/ttm: use phys_addr_t for ttm_bus_placement
drm/radeon: Only call drm_vblank_on/off between drm_vblank_init/cleanup
drm/amdgpu: fence wait old rcu slot
drm/amdgpu: fix leaking fence in the pageflip code
drm/amdgpu: print vram type rather than just DDR
drm/amdgpu/gmc: use proper register for vram type on Fiji
drm/amdgpu/gmc: move vram type fetching into sw_init
drm/amdgpu: Set vblank_disable_allowed = true
drm/radeon: Set vblank_disable_allowed = true
drm/amd/powerplay: Need to change boot to performance state in resume.
drm/amd/powerplay: add new Fiji function for not setting same ps.
drm/amdgpu: check dpm state before pm system fs initialized.
drm/amd/powerplay: notify amdgpu whether dpm is enabled or not.
drm/amdgpu: Not support disable dpm in powerplay.
drm/amdgpu: add an cgs interface to notify amdgpu the dpm state.
...
|
|
While initializing the phy, the stmmac driver sets the
PHY_IGNORE_INTERRUPT so the PAL won't call the adjust hook
that is needed, on some platforms, e.g. STi, to invoke the glue.
The patch allows the PAL to poll the stmmac_adjust_link just one time
in case of a switch is attached, setting later the PHY_IGNORE_INTERRUPT
flag.
Moving this kind of logic inside the adjust_link it makes sense to
anticipate the check for EEE that will never initialized in this
scenario.
Reported-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Tested-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Cc: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
I noticed my monitor didn't power off when it should,
this should fix it.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
This ports the DAL timeouts and MST rate calculations
for the hw from the DAL codebase.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Signed-off-by: Chunming Zhou <David1.Zhou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma fixes from Doug Ledford:
"I'm back from PTO. These issues cropped up while I was gone and are
simple fixes. I'll have more after I've caught up, but I wanted to
get these in quick.
Two minor fixes for 4.6-rc2:
- Fix mlx5 build error when on demand paging is not enabled
- Fix possible uninit variable in new i40iw driver"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma:
i40iw: avoid potential uninitialized variable use
IB/mlx5: fix VFs callback function prototypes
|
|
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
gcc finds that the i40iw_make_cm_node() function in the recently added
i40iw driver uses an uninitilized variable as an index into an array
if CONFIG_IPV6 is disabled and the driver uses IPv6 mode:
drivers/infiniband/hw/i40iw/i40iw_cm.c: In function 'i40iw_make_cm_node':
drivers/infiniband/hw/i40iw/i40iw_cm.c:2206:52: error: 'arpindex' may be used uninitialized in this function [-Werror=maybe-uninitialized]
ether_addr_copy(cm_node->rem_mac, iwdev->arp_table[arpindex].mac_addr);
As far as I can tell, this code path can not be used because the ipv4
variable is always set with CONFIG_IPV6 is disabled, but it's better
to be sure and prevent the undefined behavior, as well as shut up
that warning in a proper way.
This adds an 'else' clause for the case we get the warning about,
causing the function to return an error in a controlled way.
To avoid adding extra mess with combined io()/#ifdef clauses,
I'm also converting the existing #ifdef into a more readable
if(IS_ENABLED()) check.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: f27b4746f378 ("i40iw: add connection management code")
Acked-by: Mustafa Ismail <Mustafa.ismail@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
The previous patch that added a couple of callback functions put
the declarations inside of an #ifdef CONFIG_INFINIBAND_ON_DEMAND_PAGING,
which causes the build to fail if that option is disabled:
drivers/infiniband/hw/mlx5/main.c: In function 'mlx5_ib_add':
drivers/infiniband/hw/mlx5/main.c:2358:31: error: 'mlx5_ib_get_vf_config' undeclared (first use in this function)
This moves the four declarations below the #ifdef section so they
are always available.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: eff901d30e6c ("IB/mlx5: Implement callbacks for manipulating VFs")
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Currently drivers are limited to 19 slots for cyclic transfers.
However, if the DMA burst size is the same as the period size,
the period size can be changed to the full buffer size and
intermediate interrupts activated. Since intermediate interrupts
will trigger for each burst and the burst size is the same as
the period size, the driver will get interrupts each period as
expected. This has the benefit of allowing the functionality of
many more slots, but only uses 2 slots.
This workaround is only active if more than 19 slots are needed
and the burst size matches the period size.
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
Dmitry Torokhov
Axel Lin
Dan Williams
Bart Van Assche
Linus Torvalds
Strashko, Grygorii
Len Brown
Richard Cochran
Wolfram Sang
Greg Kroah-Hartman
Junwei Zhang
Dan Carpenter
John Keeping
Joerg Roedel
Gabriel Somlo
Michael S. Tsirkin
Bjørn Mork
Martyn Welch
Josh Boyer
Shanker Donthineni
Kees Cook
Sudip Mukherjee
Dave Airlie
Giuseppe CAVALLARO
Chunming Zhou
Hariprasad Shenai
Arnd Bergmann
John Ogness