| Age | Commit message (Collapse) | Author |
|---|
|
Initialize the gpio chip's of_node to the device's node
to work with DT based system.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The chained handler was set for the platform device with id == 0.
When the gpio devices are instantiated by a device tree, all have id ==
-1 and so the handler was unset resulting in unusable gpio irqs on
i.MX21 and i.MX27 (when using oftree).
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Without this, modules can't use this API, leading to build failures.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Not paying attention to the value being set is a bad thing because it
means that we'll not set the hardware up to reflect what was requested.
Not setting the hardware up to reflect what was requested means that the
caller won't get the results they wanted.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The feature GPIO_MSM_V1 is only available on three SoCs. On all other MSM SoCs
the INT_GPIO_GROUP{1,2} is undeclared, but Kconfig does allow such
configurations. Therefore the produced configuration is valid, but does not
compile. The problem is fixed by adding the missing Kconfig constraints.
drivers/gpio/gpio-msm-v1.c: In function âmsm_init_gpioâ:
drivers/gpio/gpio-msm-v1.c:629:26: error: 'INT_GPIO_GROUP1' undeclared
drivers/gpio/gpio-msm-v1.c:630:26: error: 'INT_GPIO_GROUP2' undeclared
Signed-off-by: Christian Dietrich <christian.dietrich@informatik.uni-erlangen.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
If there is no platform data available, the driver shouldn't use the
pointer or it will oops. Since things will mostly work nonetheless,
(the BIOS may have set up the pins properly), I'd better not fail the
probe even in this case.
Signed-off-by: Alessandro Rubini <rubini@gnudd.com>
Acked-by: Giancarlo Asnaghi <giancarlo.asnaghi@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Since commit 1c6c69525b ("genirq: Reject bogus threaded irq requests")
threaded IRQs without a primary handler need to be requested with
IRQF_ONESHOT, otherwise the request will fail. This patch adds the
IRQF_ONESHOT to input drivers where it is missing. Not modified by
this patch are those drivers where the requested IRQ will always be a
nested IRQ (e.g. because it's part of an MFD), since for this special
case IRQF_ONESHOT is not required to be specified when requesting the
IRQ.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
When inbound messages arrive, rpmsg core looks up their associated
endpoint (by destination address) and then invokes their callback.
We've made sure that endpoints will never be de-allocated after they
were found by rpmsg core, but we also need to protect against the
(rare) scenario where the rpmsg driver was just removed, and its
callback function isn't available anymore.
This is achieved by introducing a callback mutex, which must be taken
before the callback is invoked, and, obviously, before it is removed.
Cc: stable <stable@vger.kernel.org>
Reported-by: Fernando Guzman Lugo <fernando.lugo@ti.com>
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
|
|
When an inbound message arrives, the rpmsg core looks up its
associated endpoint and invokes the registered callback.
If a message arrives while its endpoint is being removed (because
the rpmsg driver was removed, or a recovery of a remote processor
has kicked in) we must ensure atomicity, i.e.:
- Either the ept is removed before it is found
or
- The ept is found but will not be freed until the callback returns
This is achieved by maintaining a per-ept reference count, which,
when drops to zero, will trigger deallocation of the ept.
With this in hand, it is now forbidden to directly deallocate
epts once they have been added to the endpoints idr.
Cc: stable <stable@vger.kernel.org>
Reported-by: Fernando Guzman Lugo <fernando.lugo@ti.com>
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
|
|
Remoteproc requires user space firmware loading support, so
let's select FW_LOADER explicitly to avoid painful misconfigurations
(which only show up in runtime).
Cc: stable <stable@vger.kernel.org>
Reported-by: Mark Grosen <mgrosen@ti.com>
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
|
|
With commit 49dca5aebfdeadd4bf27b6cb4c60392147dc35a4 I introduced
a bug (visible if CONFIG_PROVE_RCU is enabled) which occures when a panic
has happened:
[ 1526.520230] ===============================
[ 1526.520230] [ INFO: suspicious RCU usage. ]
[ 1526.520230] 3.5.0-rc1+ #12 Not tainted
[ 1526.520230] -------------------------------
[ 1526.520230] /c/kernel-tests/mm/include/linux/rcupdate.h:436 Illegal context switch in RCU read-side critical section!
[ 1526.520230]
[ 1526.520230] other info that might help us debug this:
[ 1526.520230]
[ 1526.520230]
[ 1526.520230] rcu_scheduler_active = 1, debug_locks = 0
[ 1526.520230] 3 locks held by net.agent/3279:
[ 1526.520230] #0: (&mm->mmap_sem){++++++}, at: [<ffffffff82f85962>] do_page_fault+0x193/0x390
[ 1526.520230] #1: (panic_lock){+.+...}, at: [<ffffffff82ed2830>] panic+0x37/0x1d3
[ 1526.520230] #2: (rcu_read_lock){.+.+..}, at: [<ffffffff810b9b28>] rcu_lock_acquire+0x0/0x29
[ 1526.520230]
[ 1526.520230] stack backtrace:
[ 1526.520230] Pid: 3279, comm: net.agent Not tainted 3.5.0-rc1+ #12
[ 1526.520230] Call Trace:
[ 1526.520230] [<ffffffff810e1570>] lockdep_rcu_suspicious+0x109/0x112
[ 1526.520230] [<ffffffff810bfe3a>] rcu_preempt_sleep_check+0x45/0x47
[ 1526.520230] [<ffffffff810bfe5a>] __might_sleep+0x1e/0x19a
[ 1526.520230] [<ffffffff82f8010e>] down_write+0x26/0x81
[ 1526.520230] [<ffffffff8276a966>] led_trigger_unregister+0x1f/0x9c
[ 1526.520230] [<ffffffff8276def5>] heartbeat_reboot_notifier+0x15/0x19
[ 1526.520230] [<ffffffff82f85bf5>] notifier_call_chain+0x96/0xcd
[ 1526.520230] [<ffffffff82f85cba>] __atomic_notifier_call_chain+0x8e/0xff
[ 1526.520230] [<ffffffff81094b7c>] ? kmsg_dump+0x37/0x1eb
[ 1526.520230] [<ffffffff82f85d3f>] atomic_notifier_call_chain+0x14/0x16
[ 1526.520230] [<ffffffff82ed28e1>] panic+0xe8/0x1d3
[ 1526.520230] [<ffffffff811473e2>] out_of_memory+0x15d/0x1d3
So in case of a panic, now just turn of the LED. Other approaches like
scheduling a work to unregister the trigger aren't working because there
isn't much which still runs after a panic occured (except timers).
Signed-off-by: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
|
|
OMAP_REMOTEPROC selects REMOTEPROC and RPMSG, both of which depend
on EXPERIMENTAL, so let's have OMAP_REMOTEPROC depend on EXPERIMENTAL
too, in order to avoid the below randconfig warnings.
warning: (OMAP_REMOTEPROC) selects REMOTEPROC which has unmet direct dependencies (EXPERIMENTAL)
warning: (OMAP_REMOTEPROC) selects RPMSG which has unmet direct dependencies (EXPERIMENTAL)
Cc: stable <stable@vger.kernel.org>
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
|
|
Pull fix to common clk framework from Michael Turquette:
"The previous set of common clk fixes for -rc5 left an uninitialized
int which could lead to bad array indexing when switching clock
parents. The issue is fixed with a trivial change to the code flow in
__clk_set_parent."
* tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mturquette/linux:
clk: fix parent validation in __clk_set_parent()
|
|
Pull raid10 build failure fix from NeilBrown:
"I really shouldn't do important things late in the day. It seems that
I get careless."
* tag 'md-3.5-fixes' of git://neil.brown.name/md:
md/raid10: fix careless build error
|
|
Pull networking update from David Miller:
1) Fix RX sequence number handling in mwifiex, from Stone Piao.
2) Netfilter ipset mis-compares device names, fix from Florian
Westphal.
3) Fix route leak in ipv6 IPVS, from Eric Dumazet.
4) NFS fixes. Several buffer overflows in NCI layer from Dan
Rosenberg, and release sock OOPS'er fix from Eric Dumazet.
5) Fix WEP handling ath9k, we started using a bit the chip provides to
indicate undecrypted packets but that bit turns out to be unreliable
in certain configurations. Fix from Felix Fietkau.
6) Fix Kconfig dependency bug in wlcore, from Randy Dunlap.
7) New USB IDs for rtlwifi driver from Larry Finger.
8) Fix crashes in qmi_wwan usbnet driver when disconnecting, from Bjørn
Mork.
9) Gianfar driver programs coalescing settings properly in single queue
mode, but does not do so in multi-queue mode. Fix from Claudiu
Manoil.
10) Missing module.h include in davinci_cpdma.c, from Daniel Mack.
11) Need dummy handler for IPSET_CMD_NONE otherwise we crash in ipset if
we get this via nfnetlink, fix from Tomasz Bursztyka.
12) Missing RCU unlock in nfnetlink error path, also from Tomasz.
13) Fix divide by zero in igbvf when the user tries to set an RX
coalescing value of 0 usecs, from Mitch A Williams.
14) We can process SCTP sacks for the wrong transport, oops. Fix from
Neil Horman.
15) Remove hw IP payload checksumming from e1000e driver. This has zery
value in our stack, and turning it on creates a very unintuitive
restriction for users when using jumbo MTUs.
Specifically, when IP payload checksums are on you cannot use both
receive hashing offload and jumbo MTU. Fix from Bruce Allan.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (27 commits)
e1000e: remove use of IP payload checksum
sctp: be more restrictive in transport selection on bundled sacks
igbvf: fix divide by zero
netfilter: nfnetlink: fix missing rcu_read_unlock in nfnetlink_rcv_msg
netfilter: ipset: fix crash if IPSET_CMD_NONE command is sent
davinci_cpdma: include linux/module.h
gianfar: Fix RXICr/TXICr programming for multi-queue mode
net: Downgrade CAP_SYS_MODULE deprecated message from error to warning.
net: qmi_wwan: fix Oops while disconnecting
mwifiex: fix memory leak associated with IE manamgement
ath9k: fix panic caused by returning a descriptor we have queued for reuse
mac80211: correct behaviour on unrecognised action frames
ath9k: enable serialize_regmode for non-PCIE AR9287
rtlwifi: rtl8192cu: New USB IDs
NFC: Return from rawsock_release when sk is NULL
iwlwifi: fix activating inactive stations
wlcore: drop INET dependency
ath9k: fix dynamic WEP related regression
NFC: Prevent multiple buffer overflows in NCI
netfilter: update location of my trees
...
|
|
build error introduced by commit b357f04a67c2aeee8
That function doesn't get extra args until a later patch. Bother.
Reported-by: Fengguang Wu <wfg@linux.intel.com>
Reported-by: Simon Kirby <sim@hostway.ca>
Reported-by: Tobias Klausmann <tobias.johannes.klausmann@mni.thm.de>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
In commit 070ad7e793dc ("floppy: convert to delayed work and
single-thread wq") the 'fd_timeout' timer was converted to a delayed
work. However, the "del_timer(&fd_timeout)" was lost in the process,
and any previous pending timeouts would stay active when we then
re-queued the timeout.
This resulted in the floppy probe sequence having a (stale) 20s timeout
rather than the intended 3s timeout, and thus made booting with the
floppy driver (but no actual floppy controller) take much longer than it
should.
Of course, there's little reason for most people to compile the floppy
driver into the kernel at all, which is why most people never noticed.
Canceling the delayed work where we used to do the del_timer() fixes the
issue, and makes the floppy probing use the proper new timeout instead.
The three second timeout is still very wasteful, but better than the 20s
one.
Reported-and-tested-by: Andi Kleen <ak@linux.intel.com>
Reported-and-tested-by: Calvin Walton <calvin.walton@kepstin.ca>
Cc: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull block bits from Jens Axboe:
"As vacation is coming up, thought I'd better get rid of my pending
changes in my for-linus branch for this iteration. It contains:
- Two patches for mtip32xx. Killing a non-compliant sysfs interface
and moving it to debugfs, where it belongs.
- A few patches from Asias. Two legit bug fixes, and one killing an
interface that is no longer in use.
- A patch from Jan, making the annoying partition ioctl warning a bit
less annoying, by restricting it to !CAP_SYS_RAWIO only.
- Three bug fixes for drbd from Lars Ellenberg.
- A fix for an old regression for umem, it hasn't really worked since
the plugging scheme was changed in 3.0.
- A few fixes from Tejun.
- A splice fix from Eric Dumazet, fixing an issue with pipe
resizing."
* 'for-linus' of git://git.kernel.dk/linux-block:
scsi: Silence unnecessary warnings about ioctl to partition
block: Drop dead function blk_abort_queue()
block: Mitigate lock unbalance caused by lock switching
block: Avoid missed wakeup in request waitqueue
umem: fix up unplugging
splice: fix racy pipe->buffers uses
drbd: fix null pointer dereference with on-congestion policy when diskless
drbd: fix list corruption by failing but already aborted reads
drbd: fix access of unallocated pages and kernel panic
xen/blkfront: Add WARN to deal with misbehaving backends.
blkcg: drop local variable @q from blkg_destroy()
mtip32xx: Create debugfs entries for troubleshooting
mtip32xx: Remove 'registers' and 'flags' from sysfs
blkcg: fix blkg_alloc() failure path
block: blkcg_policy_cfq shouldn't be used if !CONFIG_CFQ_GROUP_IOSCHED
block: fix return value on cfq_init() failure
mtip32xx: Remove version.h header file inclusion
xen/blkback: Copy id field when doing BLKIF_DISCARD.
|
|
A recursive lockdep warning occurs if you call
regulator_set_optimum_mode() on a regulator with a supply because
there is no nesting annotation for the rdev->mutex. To avoid this
warning, get the supply's load before locking the regulator's
mutex to avoid grabbing the same class of lock twice.
=============================================
[ INFO: possible recursive locking detected ]
3.4.0 #3257 Tainted: G W
---------------------------------------------
swapper/0/1 is trying to acquire lock:
(&rdev->mutex){+.+.+.}, at: [<c036e9e0>] regulator_get_voltage+0x18/0x38
but task is already holding lock:
(&rdev->mutex){+.+.+.}, at: [<c036ef38>] regulator_set_optimum_mode+0x24/0x224
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&rdev->mutex);
lock(&rdev->mutex);
*** DEADLOCK ***
May be due to missing lock nesting notation
3 locks held by swapper/0/1:
#0: (&__lockdep_no_validate__){......}, at: [<c03dbb48>] __driver_attach+0x40/0x8c
#1: (&__lockdep_no_validate__){......}, at: [<c03dbb58>] __driver_attach+0x50/0x8c
#2: (&rdev->mutex){+.+.+.}, at: [<c036ef38>] regulator_set_optimum_mode+0x24/0x224
stack backtrace:
[<c001521c>] (unwind_backtrace+0x0/0x12c) from [<c00cc4d4>] (validate_chain+0x760/0x1080)
[<c00cc4d4>] (validate_chain+0x760/0x1080) from [<c00cd744>] (__lock_acquire+0x950/0xa10)
[<c00cd744>] (__lock_acquire+0x950/0xa10) from [<c00cd990>] (lock_acquire+0x18c/0x1e8)
[<c00cd990>] (lock_acquire+0x18c/0x1e8) from [<c080c248>] (mutex_lock_nested+0x68/0x3c4)
[<c080c248>] (mutex_lock_nested+0x68/0x3c4) from [<c036e9e0>] (regulator_get_voltage+0x18/0x38)
[<c036e9e0>] (regulator_get_voltage+0x18/0x38) from [<c036efb8>] (regulator_set_optimum_mode+0xa4/0x224)
...
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
The below commit introduced a bug in __clk_set_parent()
which could cause it to *skip* the parent validation
which makes sure the parent passed to the api is a valid
one.
commit 7975059db572eb47f0fb272a62afeae272a4b209
Author: Rajendra Nayak <rnayak@ti.com>
Date: Wed Jun 6 14:41:31 2012 +0530
clk: Allow late cache allocation for clk->parents
This was identified by the following compiler warning..
drivers/clk/clk.c: In function '__clk_set_parent':
drivers/clk/clk.c:1083:5: warning: 'i' may be used uninitialized in this function [-Wuninitialized]
.. as reported by Marc Kleine-Budde.
There were various options discussed on how to fix this, one
being initing 'i' to clk->num_parents, but the below approach
was found to be more appropriate as it also makes the 'parent
validation' code simpler to read.
Reported-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Cc: stable@kernel.org
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm
Pull device-mapper fixes from Alasdair G Kergon:
"Four minor thin provisioning fixes and correct and update dm-verity
documentation."
* tag 'dm-3.5-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm:
dm: verity fix documentation
dm persistent data: fix allocation failure in space map checker init
dm persistent data: handle space map checker creation failure
dm persistent data: fix shadow_info_leak on dm_tm_destroy
dm thin: commit metadata before creating metadata snapshot
|
|
Pull drm fixes from Dave Airlie:
"One regression fix, two radeon fixes (one for an oops), and an i915
fix to unload framebuffers earlier.
We originally were going to leave the i915 fix until -next, but grub2
in some situations causes vesafb/efifb to be loaded now, and this
causes big slowdowns, and I have reports in rawhide I'd like to have
fixed."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/i915: kick any firmware framebuffers before claiming the gtt
drm: edid: Don't add inferred modes with higher resolution
drm/radeon: fix rare segfault
drm/radeon: fix VM page table setup on SI
|
|
Pull md fixes from NeilBrown:
"md: collection of bug fixes for 3.5
You go away for 2 weeks vacation and what do you get when you come
back? Piles of bugs :-)
Some found by inspection, some by testing, some during use in the
field, and some while developing for the next window..."
* tag 'md-3.5-fixes' of git://neil.brown.name/md:
md: fix up plugging (again).
md: support re-add of recovering devices.
md/raid1: fix bug in read_balance introduced by hot-replace
raid5: delayed stripe fix
md/raid456: When read error cannot be recovered, record bad block
md: make 'name' arg to md_register_thread non-optional.
md/raid10: fix failure when trying to repair a read error.
md/raid5: fix refcount problem when blocked_rdev is set.
md:Add blk_plug in sync_thread.
md/raid5: In ops_run_io, inc nr_pending before calling md_wait_for_blocked_rdev
md/raid5: Do not add data_offset before call to is_badblock
md/raid5: prefer replacing failed devices over want-replacement devices.
md/raid10: Don't try to recovery unmatched (and unused) chunks.
|
|
Currently the gpio _runtime_resume/suspend functions are calling the
get_context_loss_count() platform function if the function is populated for
a gpio bank. This function is used to determine if the gpio bank logic state
needs to be restored due to a power transition. This function will be populated
for all banks, but it should only be called for banks that have the
"loses_context" variable set. It is pointless to call this if loses_context is
false as we know the context will never be lost and will not need restoring.
For all OMAP2+ devices gpio bank-0 is in an always-on power domain and so will
never lose context. We found that the get_context_loss_count() was being called
for bank-0 during the probe and returning 1 instead of 0 indicating that the
context had been lost. This was causing the context restore function to be
called at probe time for this bank and because the context had never been saved,
was restoring an invalid state. This ultimately resulted in a crash [1].
This issue is a regression that was exposed by commit 1b1287032 (gpio/omap: fix
missing check in *_runtime_suspend()).
There are multiple bugs here that need to be addressed ...
1. Why the always-on power domain returns a context loss count of 1? This needs
to be fixed in the power domain code [2]. However, the gpio driver should not
assume the loss count is 0 to begin with.
2. The omap gpio driver should never be calling get_context_loss_count for a
gpio bank in a always-on domain. This is pointless and adds unneccessary
overhead.
3. The OMAP gpio driver assumes that the initial power domain context loss count
will be 0 at the time the gpio driver is probed. However, it could be
possible that this is not the case and an invalid context restore could be
performed during the probe. To avoid this only populate the
get_context_loss_count() function pointer after the initial call to
pm_runtime_get() has occurred. This will ensure that the first
pm_runtime_put() initialised the loss count correctly.
This patch addresses issues 2 and 3 above.
[1] http://marc.info/?l=linux-omap&m=134065775323775&w=2
[2] http://marc.info/?l=linux-omap&m=134100413303810&w=2
Cc: Kevin Hilman <khilman@ti.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Linus Walleij <linus.walleij@stericsson.com>
Cc: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Cc: Franky Lin <frankyl@broadcom.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: NeilBrown <neilb@suse.de>
Reported-by: Franky Lin <frankyl@broadcom.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Franky Lin <frankyl@broadcom.com>
Acked-by: Kevin Hilman <khilman@ti.com>
Tested-by: NeilBrown <neilb@suse.de>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
If CONFIG_DM_DEBUG_SPACE_MAPS is enabled and memory is fragmented and a
sufficiently-large metadata device is used in a thin pool then the space
map checker will fail to allocate the memory it requires.
Switch from kmalloc to vmalloc to allow larger virtually contiguous
allocations for the space map checker's internal count arrays.
Reported-by: Vivek Goyal <vgoyal@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
|
|
If CONFIG_DM_DEBUG_SPACE_MAPS is enabled and dm_sm_checker_create()
fails, dm_tm_create_internal() would still return success even though it
cleaned up all resources it was supposed to have created. This will
lead to a kernel crash:
general protection fault: 0000 [#1] SMP DEBUG_PAGEALLOC
...
RIP: 0010:[<ffffffff81593659>] [<ffffffff81593659>] dm_bufio_get_block_size+0x9/0x20
Call Trace:
[<ffffffff81599bae>] dm_bm_block_size+0xe/0x10
[<ffffffff8159b8b8>] sm_ll_init+0x78/0xd0
[<ffffffff8159c1a6>] sm_ll_new_disk+0x16/0xa0
[<ffffffff8159c98e>] dm_sm_disk_create+0xfe/0x160
[<ffffffff815abf6e>] dm_pool_metadata_open+0x16e/0x6a0
[<ffffffff815aa010>] pool_ctr+0x3f0/0x900
[<ffffffff8158d565>] dm_table_add_target+0x195/0x450
[<ffffffff815904c4>] table_load+0xe4/0x330
[<ffffffff815917ea>] ctl_ioctl+0x15a/0x2c0
[<ffffffff81591963>] dm_ctl_ioctl+0x13/0x20
[<ffffffff8116a4f8>] do_vfs_ioctl+0x98/0x560
[<ffffffff8116aa51>] sys_ioctl+0x91/0xa0
[<ffffffff81869f52>] system_call_fastpath+0x16/0x1b
Fix the space map checker code to return an appropriate ERR_PTR and have
dm_sm_disk_create() and dm_tm_create_internal() check for it with
IS_ERR.
Reported-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
|
|
Cleanup the shadow table before destroying the transaction manager.
Reference: leak was identified with kmemleak when running
test_discard_random_sectors in the thinp-test-suite.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
|
|
Userland sometimes sees a corrupt metadata block if metadata is changing
rapidly when a metadata snapshot is reserved for userland, To make the
problem go away, commit before we take the metadata snapshot (which is a
sensible thing to do anyway).
The checksums mean userland spots this corruption immediately so there's
no risk of acting on incorrect data. No corruption exists from the
kernel's point of view, and thin_check passes after pool shutdown.
I believe this is to do with shared blocks at the first level of the
{device, mapping} btree. Prior to the metadata-snap support no sharing
at this level was possible, so this patch is only required after commit
cc8394d86f045b86ff303d3c9e4ce47d97148951 ("dm thin: provide userspace
access to pool metadata").
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
|
|
Especially vesafb likes to map everything as uc- (yikes), and if that
mapping hangs around still while we try to map the gtt as wc the
kernel will downgrade our request to uc-, resulting in abyssal
performance.
Unfortunately we can't do this as early as readon does (i.e. as the
first thing we do when initializing the hw) because our fb/mmio space
region moves around on a per-gen basis. So I've had to move it below
the gtt initialization, but that seems to work, too. The important
thing is that we do this before we set up the gtt wc mapping.
Now an altogether different question is why people compile their
kernels with vesafb enabled, but I guess making things just work isn't
bad per se ...
v2:
- s/radeondrmfb/inteldrmfb/
- fix up error handling
v3: Kill #ifdef X86, this is Intel after all. Noticed by Ben Widawsky.
v4: Jani Nikula complained about the pointless bool primary
initialization.
v5: Don't oops if we can't allocate, noticed by Chris Wilson.
v6: Resolve conflicts with agp rework and fixup whitespace.
This is commit e188719a2891f01b3100d in drm-next.
Backport to 3.5 -fixes queue requested by Dave Airlie - due to grub
using vesa on fedora their initrd seems to load vesafb before loading
the real kms driver. So tons more people actually experience a
dead-slow gpu. Hence also the Cc: stable.
Cc: stable@vger.kernel.org
Reported-and-tested-by: "Kilarski, Bernard R" <bernard.r.kilarski@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
When a monitor EDID doesn't give the preferred bit, driver assumes
that the mode with the higest resolution and rate is the preferred
mode. Meanwhile the recent changes for allowing more modes in the
GFT/CVT ranges give actually more modes, and some modes may be over
the native size. Thus such a mode would be picked up as the preferred
mode although it's no native resolution.
For avoiding such a problem, this patch limits the addition of
inferred modes by checking not to be greater than other modes.
Also, it checks the duplicated mode entry at the same time.
Reviewed-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
In gem idle/busy ioctl the radeon object was derefenced after
drm_gem_object_unreference_unlocked which in case the object
have been destroyed lead to use of a possibly free pointer with
possibly wrong data.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
The value returned by "mddev_check_plug" is only valid until the
next 'schedule' as that will unplug things. This could happen at any
call to mempool_alloc.
So just calling mddev_check_plug at the start doesn't really make
sense.
So call it just before, or just after, queuing things for the thread.
As the action that happens at unplug is to wake the thread, this makes
lots of sense.
If we cannot add a plug (which requires a small GFP_ATOMIC alloc) we
wake thread immediately.
RAID5 is a bit different. Requests are queued for the thread and the
thread is woken by release_stripe. So we don't need to wake the
thread on failure.
However the thread doesn't perform certain actions when there is any
active plug, so it is important to install a plug before waking the
thread. So for RAID5 we install the plug *before* queuing the request
and waking the thread.
Without this patch it is possible for raid1 or raid10 to queue a
request without then waking the thread, resulting in the array locking
up.
Also change raid10 to only flush_pending_write when there are not
active plugs, just like raid1.
This patch is suitable for 3.0 or later. I plan to submit it to
-stable, but I'll like to let it spend a few weeks in mainline
first to be sure it is completely safe.
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
We currently only allow a device to be re-added if it appear to be
in-sync. This is overly restrictive as it may be desirable to re-add
a device that is in the middle of recovery.
So remove the test for "InSync" - the test on rdev->raid_disk is
sufficient to ensure that the re-add will succeed.
Reported-by: Alexander Lyakas <alex.bolshoy@gmail.com>
Tested-by: Alexander Lyakas <alex.bolshoy@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
When we added hot_replace we doubled the number of devices
that could be in a RAID1 array. So we doubled how far read_balance
would search. Unfortunately we didn't double the point at which
it looped back to the beginning - so it effectively loops over
all non-replacement disks twice.
This doesn't cause bad behaviour, but it pointless and means we
never read from replacement devices.
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
There isn't locking setting STRIPE_DELAYED and STRIPE_PREREAD_ACTIVE bits, but
the two bits have relationship. A delayed stripe can be moved to hold list only
when preread active stripe count is below IO_THRESHOLD. If a stripe has both
the bits set, such stripe will be in delayed list and preread count not 0,
which will make such stripe never leave delayed list.
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
We may not be able to fix a bad block if:
- the array is degraded
- the over-write fails.
In these cases we currently eject the device, but we should
record a bad block if possible.
Signed-off-by: majianpeng <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
Having the 'name' arg optional and defaulting to the current
personality name is no necessary and leads to errors, as when
changing the level of an array we can end up using the
name of the old level instead of the new one.
So make it non-optional and always explicitly pass the name
of the level that the array will be.
Reported-by: majianpeng <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
commit 58c54fcca3bac5bf9290cfed31c76e4c4bfbabaf
md/raid10: handle further errors during fix_read_error better.
in 3.1 added "r10_sync_page_io" which takes an IO size in sectors.
But we were passing the IO size in bytes!!!
This resulting in bio_add_page failing, and empty request being sent
down, and a consequent BUG_ON in scsi_lib.
[fix missing space in error message at same time]
This fix is suitable for 3.1.y and later.
Cc: stable@vger.kernel.org
Reported-by: Christian Balzer <chibi@gol.com>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
commit 43220aa0f22cd3ce5b30246d50ccd696d119edea
md/raid5: fix a hang on device failure.
fixed a hang, but introduced a refcounting in-balance so
that if the presence of bad-blocks ever caused an rdev to
be 'blocked' we would increment the refcount on the rdev and
never decrement it.
So added the needed rdev_dec_pending when md_wait_for_blocked_rdev
is not called.
Reported-by: majianpeng <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
Add blk_plug in sync_thread will increase the performance of sync.
Because sync_thread did not blk_plug,so when raid sync, the bio merge
not well.
Testing environment:
SATA controller: Intel Corporation 82801JI (ICH10 Family) SATA AHCI
Controller.
OS:Linux xxx 3.5.0-rc2+ #340 SMP Tue Jun 12 09:00:25 CST 2012
x86_64 x86_64 x86_64 GNU/Linux.
RAID5: four ST31000524NS disk.
Without blk_plug:recovery speed about 63M/Sec;
Add blk_plug:recovery speed about 120M/Sec.
Using blktrace:
blktrace -d /dev/sdb -w 60 -o -|blkparse -i -
without blk_plug:
Total (8,16):
Reads Queued: 309811, 1239MiB Writes Queued: 0, 0KiB
Read Dispatches: 283583, 1189MiB Write Dispatches: 0, 0KiB
Reads Requeued: 0 Writes Requeued: 0
Reads Completed: 273351, 1149MiB Writes Completed: 0, 0KiB
Read Merges: 23533, 94132KiB Write Merges: 0, 0KiB
IO unplugs: 0 Timer unplugs: 0
add blk_plug:
Total (8,16):
Reads Queued: 428697, 1714MiB Writes Queued: 0, 0KiB
Read Dispatches: 3954, 1714MiB Write Dispatches: 0, 0KiB
Reads Requeued: 0 Writes Requeued: 0
Reads Completed: 3956, 1715MiB Writes Completed: 0, 0KiB
Read Merges: 424743, 1698MiB Write Merges: 0, 0KiB
IO unplugs: 0 Timer unplugs: 3384
The ratio of merge will be markedly increased.
Signed-off-by: majianpeng <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
In ops_run_io(), the call to md_wait_for_blocked_rdev will decrement
nr_pending so we lose the reference we hold on the rdev.
So atomic_inc it first to maintain the reference.
This bug was introduced by commit 73e92e51b7969ef5477d
md/raid5. Don't write to known bad block on doubtful devices.
which appeared in 3.0, so patch is suitable for stable kernels since
then.
Cc: stable@vger.kernel.org
Signed-off-by: majianpeng <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
In chunk_aligned_read() we are adding data_offset before calling
is_badblock. But is_badblock also adds data_offset, so that is bad.
So move the addition of data_offset to after the call to
is_badblock.
This bug was introduced by commit 31c176ecdf3563140e639
md/raid5: avoid reading from known bad blocks.
which first appeared in 3.0. So that patch is suitable for any
-stable kernel from 3.0.y onwards. However it will need minor
revision for most of those (as the comment didn't appear until
recently).
Cc: stable@vger.kernel.org
Signed-off-by: majianpeng <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
If a RAID5 has both a failed device and a device marked as
'WantReplacement', then we should preferentially replace the failed
device.
However the current code replaces whichever is found first.
So split into 2 loops, check fail failed/missing first, and only check
for WantReplacement if nothing is failed or missing.
Reported-by: majianpeng <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
If a RAID10 has an odd number of chunks - as might happen when there
are an odd number of devices - the last chunk has no pair and so is
not mirrored. We don't store data there, but when recovering the last
device in an array we retry to recover that last chunk from a
non-existent location. This results in an error, and the recovery
aborts.
When we get to that last chunk we should just stop - there is nothing
more to do anyway.
This bug has been present since the introduction of RAID10, so the
patch is appropriate for any -stable kernel.
Cc: stable@vger.kernel.org
Reported-by: Christian Balzer <chibi@gol.com>
Tested-by: Christian Balzer <chibi@gol.com>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
The Microsoft LifeChat 3000 USB headset was causing a very reproducible
hang whenever it was plugged in. At first, I thought the host
controller was producing bad transfer events, because the log was filled
with errors like:
xhci_hcd 0000:00:14.0: ERROR Transfer event TRB DMA ptr not part of current TD
However, it turned out to be an xHCI driver bug in the ring expansion
patches. The bug is triggered When there are two ring segments, and a
TD that ends just before a link TRB, like so:
______________ _____________
| | ---> | setup TRB B |
______________ | _____________
| | | | data TRB B |
______________ | _____________
| setup TRB A | <-- deq | | data TRB B |
______________ | _____________
| data TRB A | | | | <-- enq, deq''
______________ | _____________
| status TRB A | | | |
______________ | _____________
| link TRB |--------------- | link TRB |
_____________ <--- deq' _____________
TD A (the first control transfer) stalls on the data phase. That halts
the ring. The xHCI driver moves the hardware dequeue pointer to the
first TRB after the stalled transfer, which happens to be the link TRB.
Once the Set TR dequeue pointer command completes, the function
update_ring_for_set_deq_completion runs. That function is supposed to
update the xHCI driver's dequeue pointer to match the internal hardware
dequeue pointer. On the first call this would work fine, and the
software dequeue pointer would move to deq'.
However, if the transfer immediately after that stalled (TD B in this
case), another Set TR Dequeue command would be issued. That would move
the hardware dequeue pointer to deq''. Once that command completed,
update_ring_for_set_deq_completion would run again.
The original code would unconditionally increment the software dequeue
pointer, which moved the pointer off the ring segment into la-la-land.
The while loop would happy increment the dequeue pointer (possibly
wrapping it) until it matched the hardware pointer value.
The while loop would also access all the memory in between the first
ring segment and the second ring segment to determine if it was a link
TRB. This could cause general protection faults, although it was
unlikely because the ring segments came from a DMA pool, and would often
have consecutive memory addresses.
If nothing in that space looked like a link TRB, the deq_seg pointer for
the ring would remain on the first segment. Thus, the deq_seg and the
software dequeue pointer would get out of sync.
When the next transfer event came in after the stalled transfer, the
xHCI driver code would attempt to convert the software dequeue pointer
into a DMA address in order to compare the DMA address for the completed
transfer. Since the deq_seg and the dequeue pointer were out of sync,
xhci_trb_virt_to_dma would return NULL.
The transfer event would get ignored, the transfer would eventually
timeout, and we would mistakenly convert the finished transfer to no-op
TRBs. Some kernel driver (maybe xHCI?) would then get stuck in an
infinite loop in interrupt context, and the whole machine would hang.
This patch should be backported to kernels as old as 3.4, that contain
the commit b008df60c6369ba0290fa7daa177375407a12e07 "xHCI: count free
TRBs on transfer ring"
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Andiry Xu <andiry.xu@amd.com>
Cc: stable@vger.kernel.org
|
|
The host controller port status register supports CAS (Cold Attach
Status) bit. This bit could be set when USB3.0 device is connected
when system is in Sx state. When the system wakes to S0 this port
status with CAS bit is reported and this port can't be used by any
device.
When CAS bit is set the port should be reset by warm reset. This
was not supported by xhci driver.
The issue was found when pendrive was connected to suspended
platform. The link state of "Compliance Mode" was reported together
with CAS bit. This link state was also not supported by xhci and
core/hub.c.
The CAS bit is defined only for xhci root hub port and it is
not supported on regular hubs. The link status is used to force
warm reset on port. Make the USB core issue a warm reset when port
is in ether the 'inactive' or 'compliance mode'. Change the xHCI driver
to report 'compliance mode' when the CAS is set. This force warm reset
on the root hub port.
This patch should be backported to stable kernels as old as 3.2, that
contain the commit 10d674a82e553cb8a1f41027bb3c3e309b3f6804 "USB: When
hot reset for USB3 fails, try warm reset."
Signed-off-by: Stanislaw Ledwon <staszek.ledwon@linux.intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Andiry Xu <andiry.xu@amd.com>
Cc: stable@vger.kernel.org
|
|
write_file_bool() modifies 32 bits of data, so "amd_iommu_unmap_flush"
needs to be 32 bits as well or we'll corrupt memory. Fortunately it
looks like the data is aligned with a gap after the declaration so this
is harmless in production.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
|
|
allo_pdir() is called in smmu_iommu_domain_init() with spin_lock
held. memory allocations in it have to be atomic/unsleepable.
Signed-off-by: Hiroshi DOYU <hdoyu@nvidia.com>
Reported-by: Chris Wright <chrisw@sous-sol.org>
Acked-by: Chris Wright <chrisw@sous-sol.org>
Cc: stable@vger.kernel.org
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
|
|
Currently only used when packet split mode is enabled with jumbo frames,
IP payload checksum (for fragmented UDP packets) is mutually exclusive with
receive hashing offload since the hardware uses the same space in the
receive descriptor for the hardware-provided packet checksum and the RSS
hash, respectively. Users currently must disable jumbos when receive
hashing offload is enabled, or vice versa, because of this incompatibility.
Since testing has shown that IP payload checksum does not provide any real
benefit, just remove it so that there is no longer a choice between jumbos
or receive hashing offload but not both as done in other Intel GbE drivers
(e.g. e1000, igb).
Also, add a missing check for IP checksum error reported by the hardware;
let the stack verify the checksum when this happens.
CC: stable <stable@vger.kernel.org> [3.4]
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Using ethtool -C ethX rx-usecs 0 crashes with a divide by zero.
Refactor this function to fix this issue and make it more clear
what the intent of each conditional is. Add comment regarding
using a setting of zero.
CC: stable <stable@vger.kernel.org> [3.3+]
CC: David Ahern <daahern@cisco.com>
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
Laxman Dewangan
Uwe Kleine-König
Stephen Warren
Mark Brown
Christian Dietrich
Alessandro Rubini
Lars-Peter Clausen
Ohad Ben-Cohen
Alexander Holler
Linus Torvalds
NeilBrown
Stephen Boyd
Rajendra Nayak
Jon Hunter
Mike Snitzer
Joe Thornber
Daniel Vetter
Takashi Iwai
Jerome Glisse
Shaohua Li
majianpeng
Sarah Sharp
Stanislaw Ledwon
Dan Carpenter
Hiroshi DOYU
Bruce Allan
Mitch A Williams