| Age | Commit message (Collapse) | Author |
|---|
|
we need to power off the PHY during suspend and
power it back on during resume.
Signed-off-by: Felipe Balbi <balbi@kernel.org>
[nsekhar@ti.com: fix call to usb_phy_set_suspend() in dwc3_suspend()]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
According to Synopsys Databook, we shouldn't be
relying on GCTL.CORESOFTRESET bit as that's only for
debugging purposes. Instead, let's use DCTL.CSFTRST
if we're OTG or PERIPHERAL mode.
Host side block will be reset by XHCI driver if
necessary. Note that this reduces amount of time
spent on dwc3_probe() by a long margin.
We're still gonna wait for reset to finish for a
long time (default to 1ms max), but tests show that
the reset polling loop executed at most 19 times
(modprobe dwc3 && modprobe -r dwc3 executed 1000
times in a row).
Suggested-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Check that dwc->maximum_speed is set to a valid value. Also add an error
when we use it later if we encounter an invalid value.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
|
|
If the maximum_speed is not set, set it to a known value, either
SuperSpeed or SuperSpeedPlus based on the type of controller we are
using. If we are on DWC_usb31 controller, check the PHY interface to see
if it is capable of SuperSpeedPlus.
Also this check is moved after dwc3_core_init() so that we can check
dwc->revision.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
|
|
The last few dev_dbg() messages are converted to
tracepoints and we can finally ignore dev_dbg()
messages during debug sessions.
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Add a quirk to clear the GUSB2PHYCFG.ENBLSLPM bit, which controls
whether the PHY receives the suspend signal from the controller.
Cc: <stable@vger.kernel.org> # v3.18+
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
This patch allows the dwc3 driver to run on the new Synopsys USB 3.1
IP core, albeit in USB 3.0 mode only.
The Synopsys USB 3.1 IP (DWC_usb31) retains mostly the same register
interface and programming model as the existing USB 3.0 controller IP
(DWC_usb3). However the GSNPSID and version numbers are different.
Add checking for the new ID to pass driver probe.
Also, since the DWC_usb31 version number is lower in value than the
full GSNPSID of the DWC_usb3 IP, we set the high bit to identify
DWC_usb31 and to ensure the values are higher.
Finally, add a documentation note about the revision numbering scheme.
Any future revision checks (for STARS, workarounds, and new features)
should take into consideration how it applies to both the 3.1/3.0 IP.
Cc: <stable@vger.kernel.org> # v3.18+
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
No functional affect on existing platforms, but the driver
is now ready to extract the properties also from ACPI tables
as well as from DT.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
By using the unified device property interface, the function
can be made available for all platforms and not just the
ones using DT.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
By using the unified device property interface, the function
can be made available for all platforms and not just the
ones using DT.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Add support for USB DRVVBUS pinctrl state change during
suspend/resume. This helps is conserving power during
system sleep.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Add adjust_frame_length_quirk for writing to fladj register
which adjusts (micro)frame length to value provided by
"snps,quirk-frame-length-adjustment" property thus avoiding
USB 2.0 devices to time-out over a longer run
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
When a SoC supports both PHY interfaces but
doesn't define HSPHY in DT/pdata, we will get
an unnecessary dev_warn() which can mislead users
into thinking that they're missing something.
Instead, let's just silently rely on a correct
default. If the HW default is wrong, then HSPHY
is required and USB won't work, this will be
motivation enough for engineers to patch their
way into a working setup.
Reported-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
commit 3e10a2ce98d1 ("usb: dwc3: add hsphy_interface
property") introduced a possible NULL pointer
dereference because dwc->hsphy_interface can be
NULL.
In order to fix it, all we have to do is guard
strncmp() against a NULL argument.
Fixes: 3e10a2ce98d1 ("usb: dwc3: add hsphy_interface property")
Tested-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Registers DWC3's ULPI interface with the ULPI bus when it's
available.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Platforms that have configured DWC_USB3_HSPHY_INTERFACE with
value 3, i.e. UTMI+ and ULPI, need to inform the driver of
the actual HSPHY interface type with the property. "utmi" if
the interface is UTMI+ or "ulpi" if the interface is ULPI.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
This allows dwc3_phy_setup() to be more useful later. There
is nothing preventing the PHY configuration registers from
being programmed early. They do not loose their context in
soft reset.
There are however other PHY related operations that should
be executed before the driver request handles to the PHYs,
such as registering DWC3's ULPI interface, which can now be
done in dwc3_phy_setup().
Also, if there ever was need for the two 100ms delays in
dwc3_phy_setup() there isn't anymore. The PHYs are now reset
after the PHY interfaces are setup.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
So it can be called from other places later.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
So they are available when ULPI interface support is added.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
We need to store it before phys are handled, so we can later
use it in ULPI interface support code.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
This patch removes "Enable USB3 LPM Capability" option from Kconfig
and adds snps,usb3_lpm_capable devicetree property instead of it.
USB3 LPM (Link Power Management) capability is hardware property, and
it's platform dependent, so if our hardware supports this feature, we
want rather to configure it in devicetree than having it as Kconfig option.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
That trick is only needed if we end up with an error, so
there's no point in messing that outside of an error path.
In fact doing so causes problems when removing dwc3.ko,
problems which commit c5a1fbc (usb: dwc3: dwc3-omap: Fix
the crash on module removal) mistakenly tried to fix.
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
By moving all dev_vdbg() to tracepoints, we
can finally get rid of dev_vdbg() usage from
dwc3.
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
as it turns out, at least AM437x silicon (non-FPGA)
needs to enable PHY suspend quirk. So let's allow
for PHY suspend quirk to be used with non-FPGA
builds too.
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
HIRD threshold should be configurable by different platforms.
From DesignWare databook:
When HIRD_Threshold[4] is set to 1b1 and HIRD value is greater than or
equal to the value in HIRD_Threshold[3:0], dwc3 asserts output signals
utmi_l1_suspend_n to put PHY into Deep Low-Power mode in L1.
When HIRD_Threshold[4] is set to 1b0 or the HIRD value is less than
HIRD_Threshold[3:0], dwc3 asserts output signals utmi_sleep_n on L1.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
This patch adds disable usb2 suspend phy quirk, and some special platforms
can configure that if it is needed.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
This patch adds disable usb3 suspend phy quirk, and some special platforms
can configure that if it is needed.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
This patch adds Tx de-emphasis quirk, and the Tx de-emphasis value is
configurable according to PIPE3 specification.
Value Description
0 -6dB de-emphasis
1 -3.5dB de-emphasis
2 No de-emphasis
3 Reserved
It can be configured on DT or platform data.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
It is recommended to set USB3 and USB2 SUSPHY bits to '1' after the core
initialization is completed above the dwc3 revision 1.94a.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
This patch adds RX_DETECT to Polling.LFPS control quirk, and some special
platforms can configure that if it is needed.
[ balbi@ti.com : added DeviceTree binding documentation ]
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
This patch adds LFPS filter quirk, and some special platforms can configure
that if it is needed.
[ balbi@ti.com : added DeviceTree binding documentation ]
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
This patch adds delay PHY power change from P0 to P1/P2/P3 when link state
changing from U0 to U1/U2/U3 respectively, and some special platforms can
configure that if it is needed.
[ balbi@ti.com : added DeviceTree binding documentation ]
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
This patch adds delay P0 to P1/P2/P3 quirk for U2/U2/U3, and some special
platforms can configure that if it is needed.
[ balbi@ti.com : added DeviceTree binding documentation ]
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
This patch adds request P1/P2/P3 quirk for U2/U2/U3, and some special
platforms can configure that if it is needed.
[ balbi@ti.com : added DeviceTree binding documentation ]
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
This patch adds P3 in U2 SS inactive quirk, and some special platforms can
configure that if it is needed.
[ balbi@ti.com : added DeviceTree binding documentation ]
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
This patch adds u2exit lfps quirk, and some special platforms can configure
that if it is needed.
[ balbi@ti.com : added DeviceTree binding documentation ]
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
When parameter DWC_USB3_LPM_ERRATA_ENABLE is enabled in Andvanced
Configuration of coreConsultant, it supports of xHCI BESL Errata Dated
10/19/2011 is enabled in host mode. In device mode it adds the capability
to send NYET response threshold based on the BESL value received in the LPM
token, and the threhold is configurable for each soc platform.
This patch adds an entry that soc platform is able to define the lpm
capacity with their own device tree or bus glue layer.
[ balbi@ti.com : added devicetree documentation, spelled threshold
completely, made sure threshold is only applied to
proper core revisions. ]
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
This patch adds disscramble quirk, and it only needs to be enabled at fpga
board on some vendor platforms.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Some chip vendor is on pre-silicon phase, which needs to use the simulation
board. It should have the same product and vendor id with the true soc, but
might have some minor different configurations.
Below thread discussion proposes to find a method to distinguish between
simulation board and soc.
http://marc.info/?l=linux-usb&m=141194772206369&w=2
In Andvanced Configuration of coreConsultant, there is the parameter of
DWC_USB_EN_FPGA. This bit has the function we need. And it would response as 7
bit of GHWPARAMS6 register. So it's able to check this functional bit to confirm
if works on FPGA board.
Reported-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
It enables hibernation if the function is set in coreConsultant.
Suggested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Using ->prepare()/->complete() to mask/unmask
IRQs is wrong at least for dwc3. We need to
make sure that by the end of ->resume(), IRQs
are working and ready to fire because a child
device may need working IRQs for its own ->resume()
method.
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Adding ACPI ID used on newer Intel SoCs.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
If the probe drivers have already set the dma_mask, not
replacing the value.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
DWC3's GUID register is supposed to be used to write
any sort of version we might want. It helps when getting
bug reports for platforms you don't have HW to know
which kernel version of the driver was running on the
platform.
Because we don't really track driver version, but we _do_
track the kernel version, let's write LINUX_VERSION_CODE to
that register and use it for debugging.
Reviewed-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Linux 3.17-rc5
Signed-off-by: Felipe Balbi <balbi@ti.com>
Conflicts:
Documentation/devicetree/bindings/usb/mxs-phy.txt
drivers/usb/phy/phy-mxs-usb.c
|
|
We can't suspend the PHYs before dwc3_core_exit_mode()
has been called, that's because the host and/or device
sides might still need to communicate with the far end
link partner.
Fixes: 8ba007a (usb: dwc3: core: enable the USB2 and USB3 phy in probe)
Cc: <stable@vger.kernel.org> # v3.9+
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Currently, we disable pm_runtime before all register
accesses are done, this is dangerous and might lead
to abort exceptions due to the driver trying to access
a register which is clocked by a clock which was long
gated.
Fix that by moving pm_runtime_put_sync() and pm_runtime_disable()
as the last thing we do before returning from our ->remove()
method.
Fixes: 72246da (usb: Introduce DesignWare USB3 DRD Driver)
Cc: <stable@vger.kernel.org> # v3.2+
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Newer DWC3 controllers can be built for USB 2.0-only mode, where
most of the USB 3.0 circuitry is left out. To support this mode,
the driver must limit the speed programmed into the DCFG register
to Hi-Speed or lower.
Reads and writes to the PIPECTL register are left as-is, since
they should be no-ops in USB 2.0-only mode. Calls to phy_init()
etc. for the USB3 phy are also left as-is, since the no-op USB3
phy should be used for USB 2.0-only mode controllers.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Putting together the code related to getting the 'IORESOURCE_MEM'
and assigning the same to dwc->xhci_resources, for increasing
the readability.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
Felipe Balbi
Felipe Balbi
John Youn
Felipe Balbi
Heikki Krogerus
Sekhar Nori
Nikhil Badola
Robert Baldyga
Huang Rui
Jingoo Han
Paul Zimmerman
Vivek Gautam