| Age | Commit message (Collapse) | Author |
|---|
|
Use imx6sx instead of imx6sl's platform flags for imx6sx.
Fixes: e14db48dfcf3 ("usb: chipidea: imx: add runtime power management support")
Cc: <stable@vger.kernel.org> # v4.1+
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
|
|
Stream mode enable is known for better performance, this stream mode
enable patch has been passed with stress tests at device mode for
imx6sl and imx6sx, and no issue is found.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
|
|
If usbmisc hasn't probed yet, defer the probe.
It's not enough to check if the platform device for the OF node of the
usbmisc has been registered, but it also needs to have been probed
already before we can call imx_usbmisc_init().
This can happen if the order in which devices are probed change due to
async probing or on-demand probing of dependencies.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
|
|
For i.mx platform, set ttctrl.ttha with non-zero value only affects
sitd, and ehci core makes sure the schedule is not full when accepts
new request, so it will not occur the transaction which will acorss
the SoF.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
|
|
Some usb PHYs need power supply from vbus to make it work, eg mxs-phy, if
there is no vbus, USB PHY will not in correct state when the controller starts
to work, for host, this requires vbus should be turned on before setting port
power(PP) of ehci, to work with this kind of USB PHY design, this patch adds
a flag CI_HDRC_TURN_VBUS_EARLY_ON, can be checked by host driver to turn on
vbus while start host.
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Enable USB as system wakeup source, and each platform needs to implement
imx_usbmisc_set_wakeup in usbmisc_imx.c to support.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add runtime pm support for imx, only imx6 series are supported and tested.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Move struct imx_usbmisc_data NULL pointer judgement from caller to
each API, it can simplify the caller.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
It is meaningless the glue layer driver has its own platform flag
which is the same meaning with common platform flag.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
|
|
Now, USB PHY is mandatory for chipidea core, the flag
CI_HDRC_REQUIRE_TRANSCEIVER is useless.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add basic system power management support
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
MM core code already complains when devm_kzalloc() fails, so no need to print
the error locally.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch modify the generic code handling PHYs to allow them to be
supplied from the drivers. This adds checks to ensure no PHY was already
there when looking for one in the generic code. This also makes sure we
do not modify its state in the generic HCD functions, it was provided by
the driver.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
A platform_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
This adds Vybrid VF610 SoC support. The IP is very similar to i.MX6,
however, the non-core registers are spread in two different register
areas. Hence we support multiple instances of the USB misc driver
and add the driver instance to the imx_usbmisc_data structure.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
-ENODEV is interpreted by the generic driver probing function as a
non-matching driver. This leads to a missing probe failure message.
Also a missing USB PHY is more of an invalid configuration of the usb
driver because it is necessary.
This patch returns -EINVAL if devm_usb_get_phy_by_phandle() returned -ENODEV.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use dev_name() for ci_hdrc name to distinguish USBs
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Due to imx28 needs ARM swp instruction for writing, we set
CI_HDRC_IMX28_WRITE_FIX for imx28.
This patch is needed for stable tree 3.11+
Cc: stable@vger.kernel.org
Cc: robert.hodaszi@digi.com
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Tested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit 30666249eae3b04875d514dea557d1ab1468c006, as it
depended on a previous patch that I rejected, causing a build error
here. Sorry about that.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Cc: Peter Chen <peter.chen@freescale.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Due to imx28 needs ARM swp instruction for writing, we set
CI_HDRC_IMX28_WRITE_FIX for imx28.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Tested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Pull DMA mask updates from Russell King:
"This series cleans up the handling of DMA masks in a lot of drivers,
fixing some bugs as we go.
Some of the more serious errors include:
- drivers which only set their coherent DMA mask if the attempt to
set the streaming mask fails.
- drivers which test for a NULL dma mask pointer, and then set the
dma mask pointer to a location in their module .data section -
which will cause problems if the module is reloaded.
To counter these, I have introduced two helper functions:
- dma_set_mask_and_coherent() takes care of setting both the
streaming and coherent masks at the same time, with the correct
error handling as specified by the API.
- dma_coerce_mask_and_coherent() which resolves the problem of
drivers forcefully setting DMA masks. This is more a marker for
future work to further clean these locations up - the code which
creates the devices really should be initialising these, but to fix
that in one go along with this change could potentially be very
disruptive.
The last thing this series does is prise away some of Linux's addition
to "DMA addresses are physical addresses and RAM always starts at
zero". We have ARM LPAE systems where all system memory is above 4GB
physical, hence having DMA masks interpreted by (eg) the block layers
as describing physical addresses in the range 0..DMAMASK fails on
these platforms. Santosh Shilimkar addresses this in this series; the
patches were copied to the appropriate people multiple times but were
ignored.
Fixing this also gets rid of some ARM weirdness in the setup of the
max*pfn variables, and brings ARM into line with every other Linux
architecture as far as those go"
* 'for-linus-dma-masks' of git://git.linaro.org/people/rmk/linux-arm: (52 commits)
ARM: 7805/1: mm: change max*pfn to include the physical offset of memory
ARM: 7797/1: mmc: Use dma_max_pfn(dev) helper for bounce_limit calculations
ARM: 7796/1: scsi: Use dma_max_pfn(dev) helper for bounce_limit calculations
ARM: 7795/1: mm: dma-mapping: Add dma_max_pfn(dev) helper function
ARM: 7794/1: block: Rename parameter dma_mask to max_addr for blk_queue_bounce_limit()
ARM: DMA-API: better handing of DMA masks for coherent allocations
ARM: 7857/1: dma: imx-sdma: setup dma mask
DMA-API: firmware/google/gsmi.c: avoid direct access to DMA masks
DMA-API: dcdbas: update DMA mask handing
DMA-API: dma: edma.c: no need to explicitly initialize DMA masks
DMA-API: usb: musb: use platform_device_register_full() to avoid directly messing with dma masks
DMA-API: crypto: remove last references to 'static struct device *dev'
DMA-API: crypto: fix ixp4xx crypto platform device support
DMA-API: others: use dma_set_coherent_mask()
DMA-API: staging: use dma_set_coherent_mask()
DMA-API: usb: use new dma_coerce_mask_and_coherent()
DMA-API: usb: use dma_set_coherent_mask()
DMA-API: parport: parport_pc.c: use dma_coerce_mask_and_coherent()
DMA-API: net: octeon: use dma_coerce_mask_and_coherent()
DMA-API: net: nxp/lpc_eth: use dma_coerce_mask_and_coherent()
...
|
|
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The correct way for a driver to specify the coherent DMA mask is
not to directly access the field in the struct device, but to use
dma_set_coherent_mask(). Only arch and bus code should access this
member directly.
Convert all direct write accesses to using the correct API.
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Since the PHY operations are moved to core, delete the related
code at glue layer.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If not, the PHY will be active even the controller is not in use.
We find this issue due to the PHY's clock refcount is not correct
due to -EPROBE_DEFER return after phy's init.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The chipidea i.MX driver is split into two drivers. The ci_hdrc_imx driver
handles the chipidea cores and the usbmisc_imx driver handles the noncore
registers common to all chipidea cores (but SoC specific). Current flow is:
- usbmisc sets an ops pointer in the ci_hdrc_imx driver during probe
- ci_hdrc_imx checks if the pointer is valid during probe, if yes calls
the functions in the ops pointer.
- usbmisc_imx calls back into the ci_hdrc_imx driver to get additional
data
This is overly complicated and has problems if the drivers are compiled
as modules. In this case the usbmisc_imx driver can be unloaded even if
the ci_hdrc_imx driver still needs usbmisc functionality.
This patch changes this by letting the ci_hdrc_imx driver calling functions
from the usbmisc_imx driver. This way the symbol resolving during module
load makes sure the ci_hdrc_imx driver depends on the usbmisc_imx driver.
Also instead of letting the usbmisc_imx driver call back into the ci_hdrc_imx
driver, pass the needed data in the first place.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Currently, the controller only runs when the ci->vbus_active is true.
So the flag CI_HDRC_PULLUP_ON_VBUS is useless no longer.
If the user doesn't have otgsc, he/she needs to change ci_handle_vbus_change
to update ci->vbus_active.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The vbus regulator is a common element for USB vbus operation,
So, move it from glue layer to core.
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
ci_hdrc_imx_remove()
This prevents the USB PHY refcount to be decremented below zero upon
unloading the ci-hdrc-imx module.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Remove an unused macro leftover from the old initialization code.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
'res' is not used anywhere, so let's get rid of it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ea1418b5f1a (usb: chipidea: i.MX: use devm_usb_get_phy_by_phandle to get
phy) causes the USB host to miss the disconnect/connect events.
In order to reproduce this problem:
- Insert a USB thumb into the USB host port (connection is detected)
- Remove it (no disconnect event will be reported)
- Insert the USB thumb again (connection is not detected)
Fix this problem by accessing the usb_phy structure using the private data
instead of accessing a local structure.
Tested on a mx28evk board.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
"ci13xxx" is bad for at least the following reasons:
* people often mistype it
* it doesn't add any informational value to the names it's used in
* it needlessly attracts mail filters
This patch replaces it with "ci_hdrc", "ci_udc" or "ci_hw", depending
on the situation. Modules with ci13xxx prefix are also renamed accordingly
and aliases are added for compatibility. Otherwise, no functional changes.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
Li Jun
Peter Chen
Tomeu Vizoso
Li Jun
Linus Torvalds
Fabio Estevam
Antoine Tenart
Wolfram Sang
Stefan Agner
Markus Pargmann
Alexander Shiyan
Greg Kroah-Hartman
Russell King
Sascha Hauer
Lothar Waßmann
Alexander Shishkin