| Age | Commit message (Collapse) | Author |
|---|
|
The configurations are not modified by the driver. Make them 'const' so
that they may be placed in a read-only section.
Signed-off-by: Josh Cartwright <joshc@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Kvaser firmware can only read and write messages that are
not crossing the USB endpoint's wMaxPacketSize boundary. While
receiving commands from the CAN device, if the next command in
the same URB buffer crossed that max packet size boundary, the
firmware puts a zero-length placeholder command in its place
then moves the real command to the next boundary mark.
The driver did not recognize such behavior, leading to missing
a good number of rx events during a heavy rx load session.
Moreover, a tx URB context only gets freed upon receiving its
respective tx ACK event. Over time, the free tx URB contexts
pool gets depleted due to the missing ACK events. Consequently,
the netif transmission queue gets __permanently__ stopped; no
frames could be sent again except after restarting the CAN
newtwork interface.
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Upon a URB submission failure, the driver calls usb_free_urb()
but then manually frees the URB buffer by itself. Meanwhile
usb_free_urb() has alredy freed out that transfer buffer since
we're the only code path holding a reference to this URB.
Remove two of such invalid manual free().
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Fixes a missing initialization of ctrlmode and ctrlmode_supported fields,
for all other CAN devices than the first one. This fix only concerns
the PCAN-USB Pro FD dual-channels CAN-FD device made by PEAK-System.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
When accessing CAN network interfaces with AF_PACKET sockets e.g. by dhclient
this can lead to a skb_under_panic due to missing skb initialisations.
Add the missing initialisations at the CAN skbuff creation times on driver
level (rx path) and in the network layer (tx path).
Reported-by: Austin Schuh <austin@peloton-tech.com>
Reported-by: Daniel Steer <daniel.steer@mclaren.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
On my test environment the throughput of a file transfer drops
from 4.4MBps to 116KBps due the number of repeated warning
messages. This patch removes the warning messages as DMA works
correctly with addresses using 0xC0000000 bits.
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Acked-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the driver is removed (e.g. using unbind through sysfs), the
clocks get disabled twice, once on fec_enet_close and once on
fec_drv_remove. Since the clocks are enabled only once, this leads
to a warning:
WARNING: CPU: 0 PID: 402 at drivers/clk/clk.c:992 clk_core_disable+0x64/0x68()
Remove the call to fec_enet_clk_enable in fec_drv_remove to balance
the clock enable/disable calls again. This has been introduce by
e8fcfcd5684a ("net: fec: optimize the clock management to save power").
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The latest spec "I-IPA01-0266-USR Rev 10" limit the MID field length to 12 bit
value. For previous versions it is 16 bit value.
This change will not break the backward compatibility as the latest ID value is
7 and with in the 12 bit value limit.
Signed-off-by: Punnaiah Choudary Kalluri <punnaia@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
eTSEC of-nodes may have children which are not queue-group nodes. For
example new-style fixed-phy declarations. These where incorrectly
assumed to be additional queue-groups.
Change the search to filter out any nodes which are not queue-groups,
or have been disabled.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
bcmgenet_set_wol() correctly sets MPD_PW_EN when a password is specified
to match magic packets against, however, when we switch from a
password-matching to a matching without password we would leave this bit
turned on, and GENET would only match magic packets with passwords.
This can be reproduced using the following sequence:
ethtool -s eth0 wol g
ethtool -s eth0 wol s sopass 00:11:22:33:44:55
ethtool -s eth0 wol g
The simple fix is to clear the MPD_PWD_EN bit when WAKE_MAGICSECURE is
not set.
Fixes: c51de7f3976b ("net: bcmgenet: add Wake-on-LAN support code")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit de7b5b3d790a ("net: eth: xgene: change APM X-Gene SoC platform
ethernet to support ACPI") breaks booting with devicetree with UEFI
firmware. In that case, I get:
Unhandled fault: synchronous external abort (0x96000010) at 0xfffffc0000620010
Internal error: : 96000010 [#1] SMP
Modules linked in: vfat fat xfs libcrc32c ahci_xgene libahci_platform libahci
CPU: 7 PID: 634 Comm: NetworkManager Not tainted 4.0.0-rc1+ #4
Hardware name: AppliedMicro Mustang/Mustang, BIOS 1.1.0-rh-0.14 Mar 1 2015
task: fffffe03d4c7e100 ti: fffffe03d4e24000 task.ti: fffffe03d4e24000
PC is at xgene_enet_rd_mcx_mac.isra.11+0x58/0xd4
LR is at xgene_gmac_tx_enable+0x2c/0x50
pc : [<fffffe000069d6fc>] lr : [<fffffe000069dcc4>] pstate: 80000145
sp : fffffe03d4e27590
x29: fffffe03d4e27590 x28: 0000000000000000
x27: fffffe03d4e277c0 x26: fffffe03da8fda10
x25: fffffe03d4e2760c x24: fffffe03d49e28c0
x23: fffffc0000620004 x22: 0000000000000000
x21: fffffc0000620000 x20: fffffc0000620010
x19: 000000000000000b x18: 000003ffd4a96020
x17: 000003ff7fc1f7a0 x16: fffffe000079b9cc
x15: 0000000000000000 x14: 0000000000000000
x13: 0000000000000000 x12: fffffe03d4e24000
x11: fffffe03d4e27da0 x10: 0000000000000001
x9 : 0000000000000000 x8 : fffffe03d4e27a20
x7 : 0000000000000000 x6 : 00000000ffffffef
x5 : fffffe000105f7d0 x4 : fffffe00007ca8c8
x3 : fffffe03d4e2760c x2 : 0000000000000000
x1 : fffffc0000620000 x0 : 0000000040000000
Process NetworkManager (pid: 634, stack limit = 0xfffffe03d4e24028)
Stack: (0xfffffe03d4e27590 to 0xfffffe03d4e28000)
...
Call trace:
[<fffffe000069d6fc>] xgene_enet_rd_mcx_mac.isra.11+0x58/0xd4
[<fffffe000069dcc0>] xgene_gmac_tx_enable+0x28/0x50
[<fffffe00006a112c>] xgene_enet_open+0x2c/0x130
[<fffffe00007b9254>] __dev_open+0xc8/0x148
[<fffffe00007b956c>] __dev_change_flags+0x90/0x158
[<fffffe00007b9664>] dev_change_flags+0x30/0x70
[<fffffe00007c8ab8>] do_setlink+0x278/0x870
[<fffffe00007c95bc>] rtnl_newlink+0x404/0x6a8
[<fffffe00007c8040>] rtnetlink_rcv_msg+0x98/0x218
[<fffffe00007e78e4>] netlink_rcv_skb+0xe0/0xf8
[<fffffe00007c7f94>] rtnetlink_rcv+0x30/0x44
[<fffffe00007e6f2c>] netlink_unicast+0xfc/0x210
[<fffffe00007e75b8>] netlink_sendmsg+0x498/0x5ac
[<fffffe00007990b8>] do_sock_sendmsg+0xa4/0xcc
[<fffffe000079a958>] ___sys_sendmsg+0x1fc/0x208
[<fffffe000079b984>] __sys_sendmsg+0x4c/0x94
[<fffffe000079b9f8>] SyS_sendmsg+0x2c/0x3c
The problem here is that the enet hw clocks are not getting
initialized because of a test to avoid the initialization if
UEFI is used to boot. This is an incorrect test. When booting
with UEFI and devicetree, the kernel must still initialize
the enet hw clocks. If booting with ACPI, the clock hw is
not exposed to the kernel and it is that case where we want
to avoid initializing clocks.
Signed-off-by: Mark Salter <msalter@redhat.com>
Acked-by: Feng Kan <fkan@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
EEH recovery for bnx2x based adapters is not reliable on all Power
systems using the default hot reset, which can result in an
unrecoverable EEH error. Forcing the use of fundamental reset
during EEH recovery fixes this.
Cc: stable<stable@vger.kernel.org>
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When handling a from-guest frag list, xenvif_handle_frag_list()
replaces the frags before calling the destructor to clean up the
original (foreign) frags. Whilst this is safe (the destructor doesn't
actually use the frags), it looks odd.
Reorder the function to be less confusing.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Every time a VIF is destroyed up to 256 pages may be leaked if packets
with more than MAX_SKB_FRAGS frags were transmitted from the guest.
Even worse, if another user of ballooned pages allocated one of these
ballooned pages it would not handle the unexpectedly >1 page count
(e.g., gntdev would deadlock when unmapping a grant because the page
count would never reach 1).
When handling a from-guest skb with a frag list, unref the frags
before releasing them so they are freed correctly when the VIF is
destroyed.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use correct pointer arithmetic to get the pointer to each stat.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
I recently did a rework of the smc91x driver and did some build-testing
by compiling hundreds of randconfig kernels. Unfortunately, my script
was wrong and did not actually test the configurations that mattered,
so I introduced stupid typos in almost every file I touched.
I fixed my script now, built all configurations that actually matter
and fixed all the typos, this is the result.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: b70661c70830d ("net: smc91x: use run-time configuration on all ARM machines")
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently the list is traversed using rcu variant. That is not correct
since dev_set_mac_address can be called which eventually calls
rtmsg_ifinfo_build_skb and there, skb allocation can sleep. So fix this
by remove the rcu usage here.
Fixes: 3d249d4ca7 "net: introduce ethernet teaming device"
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When do suspend/resume stress test, some log shows "rcv is not +last".
The issue is that enet suspend will disable phy clock, phy link down,
after resume back, enet MAC redo initial and ready to tx/rx packet,
but phy still is not ready which is doing auto-negotiation. When phy
link is not up, don't schdule napi soft irq.
[Peter]
It has fixed kernel panic after long time suspend/resume test
with nfs rootfs.
[ 8864.429458] fec 2188000.ethernet eth0: rcv is not +last
[ 8864.434799] fec 2188000.ethernet eth0: rcv is not +last
[ 8864.440088] fec 2188000.ethernet eth0: rcv is not +last
[ 8864.445424] fec 2188000.ethernet eth0: rcv is not +last
[ 8864.450782] fec 2188000.ethernet eth0: rcv is not +last
[ 8864.456111] Unable to handle kernel NULL pointer dereference at virtual address 00000000
[ 8864.464225] pgd = 80004000
[ 8864.466997] [00000000] *pgd=00000000
[ 8864.470627] Internal error: Oops: 17 [#1] SMP ARM
[ 8864.475353] Modules linked in: evbug
[ 8864.479006] CPU: 0 PID: 3 Comm: ksoftirqd/0 Not tainted 4.0.0-rc1-00044-g7a2a1d2 #234
[ 8864.486854] Hardware name: Freescale i.MX6 SoloX (Device Tree)
[ 8864.492709] task: be069380 ti: be07a000 task.ti: be07a000
[ 8864.498137] PC is at memcpy+0x80/0x330
[ 8864.501919] LR is at gro_pull_from_frag0+0x34/0xa8
[ 8864.506735] pc : [<802bb080>] lr : [<8057c204>] psr: 00000113
[ 8864.506735] sp : be07bbd4 ip : 00000010 fp : be07bc0c
[ 8864.518235] r10: 0000000e r9 : 00000000 r8 : 809c7754
[ 8864.523479] r7 : 809c7754 r6 : bb43c040 r5 : bd280cc0 r4 : 00000012
[ 8864.530025] r3 : 00000804 r2 : fffffff2 r1 : 00000000 r0 : bb43b83c
[ 8864.536575] Flags: nzcv IRQs on FIQs on Mode SVC_32 ISA ARM Segment kernel
[ 8864.543904] Control: 10c5387d Table: bd14c04a DAC: 00000015
[ 8864.549669] Process ksoftirqd/0 (pid: 3, stack limit = 0xbe07a210)
[ 8864.555869] Stack: (0xbe07bbd4 to 0xbe07c000)
[ 8864.560250] bbc0: bd280cc0 bb43c040 809c7754
[ 8864.568455] bbe0: 809c7754 bb43b83c 00000012 8057c204 00000000 bd280cc0 bd8a0718 00000003
[ 8864.576658] bc00: be07bc5c be07bc10 8057ebf0 8057c1dc 00000000 00000000 8057ecc4 bef59760
[ 8864.584863] bc20: 00000002 bd8a0000 be07bc64 809c7754 00000000 bd8a0718 bd280cc0 bd8a0000
[ 8864.593066] bc40: 00000000 0000001c 00000000 bd8a0000 be07bc74 be07bc60 8057f148 8057eb90
[ 8864.601268] bc60: bf0810a0 00000000 be07bcf4 be07bc78 8044e7b4 8057f12c 00000000 8007df6c
[ 8864.609470] bc80: bd8a0718 00000040 00000000 bd280a80 00000002 00000019 bd8a0600 bd8a1214
[ 8864.617672] bca0: bd8a0690 bf0810a0 00000000 00000000 bd8a1000 00000000 00000027 bd280cc0
[ 8864.625874] bcc0: 80062708 800625cc 000943db bd8a0718 00000001 000d1166 00000040 be7c1ec0
[ 8864.634077] bce0: 0000012c be07bd00 be07bd3c be07bcf8 8057fc98 8044e3ac 809c2ec0 3ddff000
[ 8864.642280] bd00: be07bd00 be07bd00 be07bd08 be07bd08 00000000 00000020 809c608c 00000003
[ 8864.650481] bd20: 809c6080 40000001 809c6088 00200100 be07bd84 be07bd40 8002e690 8057fac8
[ 8864.658684] bd40: be07bd64 be07bd50 00000001 04208040 000d1165 0000000a be07bd84 809c0d7c
[ 8864.666885] bd60: 00000000 809c6af8 00000000 00000001 be008000 00000000 be07bd9c be07bd88
[ 8864.675087] bd80: 8002eb64 8002e564 00000125 809c0d7c be07bdc4 be07bda0 8006f100 8002eaac
[ 8864.683291] bda0: c080e10c be07bde8 809c6c6c c080e100 00000002 00000000 be07bde4 be07bdc8
[ 8864.691492] bdc0: 800087a0 8006f098 806f2934 20000013 ffffffff be07be1c be07be44 be07bde8
[ 8864.699695] bde0: 800133a4 80008784 00000001 00000001 00000000 00000000 be7c1680 00000000
[ 8864.707896] be00: be0cfe00 bd93eb40 00000002 00000000 00000000 be07be44 be07be00 be07be30
[ 8864.716098] be20: 8006278c 806f2934 20000013 ffffffff be069380 be7c1680 be07be7c be07be48
[ 8864.724300] be40: 80049cfc 806f2910 00000001 00000000 80049cb4 00000000 be07be7c be7c1680
[ 8864.732502] be60: be3289c0 be069380 bd23b600 be0cfe00 be07bebc be07be80 806ed614 80049c68
[ 8864.740706] be80: be07a000 0000020a 809c608c 00000003 00000001 8002e858 be07a000 be035740
[ 8864.748907] bea0: 00000000 00000001 809d4598 00000000 be07bed4 be07bec0 806edd0c 806ed440
[ 8864.757110] bec0: be07a000 be07a000 be07bee4 be07bed8 806edd68 806edcf0 be07bef4 be07bee8
[ 8864.765311] bee0: 8002e860 806edd34 be07bf24 be07bef8 800494b0 8002e828 be069380 00000000
[ 8864.773512] bf00: be035780 be035740 8004938c 00000000 00000000 00000000 be07bfac be07bf28
[ 8864.781715] bf20: 80045928 80049398 be07bf44 00000001 00000000 be035740 00000000 00030003
[ 8864.789917] bf40: dead4ead ffffffff ffffffff 80a2716c 80b59b00 00000000 8088c954 be07bf5c
[ 8864.798120] bf60: be07bf5c 00000000 00000000 dead4ead ffffffff ffffffff 80a2716c 00000000
[ 8864.806320] bf80: 00000000 8088c954 be07bf88 be07bf88 be035780 8004584c 00000000 00000000
[ 8864.814523] bfa0: 00000000 be07bfb0 8000ed10 80045858 00000000 00000000 00000000 00000000
[ 8864.822723] bfc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 8864.830925] bfe0: 00000000 00000000 00000000 00000000 00000013 00000000 5ffbb5f7 f9fcf5e7
[ 8864.839115] Backtrace:
[ 8864.841631] [<8057c1d0>] (gro_pull_from_frag0) from [<8057ebf0>] (dev_gro_receive+0x6c/0x3f8)
[ 8864.850173] r6:00000003 r5:bd8a0718 r4:bd280cc0 r3:00000000
[ 8864.855958] [<8057eb84>] (dev_gro_receive) from [<8057f148>] (napi_gro_receive+0x28/0xac)
[ 8864.864152] r10:bd8a0000 r9:00000000 r8:0000001c r7:00000000 r6:bd8a0000 r5:bd280cc0
[ 8864.872115] r4:bd8a0718
[ 8864.874713] [<8057f120>] (napi_gro_receive) from [<8044e7b4>] (fec_enet_rx_napi+0x414/0xc74)
[ 8864.883167] r5:00000000 r4:bf0810a0
[ 8864.886823] [<8044e3a0>] (fec_enet_rx_napi) from [<8057fc98>] (net_rx_action+0x1dc/0x2ec)
[ 8864.895016] r10:be07bd00 r9:0000012c r8:be7c1ec0 r7:00000040 r6:000d1166 r5:00000001
[ 8864.902982] r4:bd8a0718
[ 8864.905570] [<8057fabc>] (net_rx_action) from [<8002e690>] (__do_softirq+0x138/0x2c4)
[ 8864.913417] r10:00200100 r9:809c6088 r8:40000001 r7:809c6080 r6:00000003 r5:809c608c
[ 8864.921382] r4:00000020
[ 8864.923966] [<8002e558>] (__do_softirq) from [<8002eb64>] (irq_exit+0xc4/0x138)
[ 8864.931289] r10:00000000 r9:be008000 r8:00000001 r7:00000000 r6:809c6af8 r5:00000000
[ 8864.939252] r4:809c0d7c
[ 8864.941841] [<8002eaa0>] (irq_exit) from [<8006f100>] (__handle_domain_irq+0x74/0xe8)
[ 8864.949688] r4:809c0d7c r3:00000125
[ 8864.953342] [<8006f08c>] (__handle_domain_irq) from [<800087a0>] (gic_handle_irq+0x28/0x68)
[ 8864.961707] r9:00000000 r8:00000002 r7:c080e100 r6:809c6c6c r5:be07bde8 r4:c080e10c
[ 8864.969597] [<80008778>] (gic_handle_irq) from [<800133a4>] (__irq_svc+0x44/0x5c)
[ 8864.977097] Exception stack(0xbe07bde8 to 0xbe07be30)
[ 8864.982173] bde0: 00000001 00000001 00000000 00000000 be7c1680 00000000
[ 8864.990377] be00: be0cfe00 bd93eb40 00000002 00000000 00000000 be07be44 be07be00 be07be30
[ 8864.998573] be20: 8006278c 806f2934 20000013 ffffffff
[ 8865.003638] r7:be07be1c r6:ffffffff r5:20000013 r4:806f2934
[ 8865.009447] [<806f2904>] (_raw_spin_unlock_irq) from [<80049cfc>] (finish_task_switch+0xa0/0x160)
[ 8865.018334] r4:be7c1680 r3:be069380
[ 8865.021993] [<80049c5c>] (finish_task_switch) from [<806ed614>] (__schedule+0x1e0/0x5dc)
[ 8865.030098] r8:be0cfe00 r7:bd23b600 r6:be069380 r5:be3289c0 r4:be7c1680
[ 8865.036942] [<806ed434>] (__schedule) from [<806edd0c>] (preempt_schedule_common+0x28/0x44)
[ 8865.045307] r9:00000000 r8:809d4598 r7:00000001 r6:00000000 r5:be035740 r4:be07a000
[ 8865.053197] [<806edce4>] (preempt_schedule_common) from [<806edd68>] (_cond_resched+0x40/0x48)
[ 8865.061822] r4:be07a000 r3:be07a000
[ 8865.065472] [<806edd28>] (_cond_resched) from [<8002e860>] (run_ksoftirqd+0x44/0x64)
[ 8865.073252] [<8002e81c>] (run_ksoftirqd) from [<800494b0>] (smpboot_thread_fn+0x124/0x190)
[ 8865.081550] [<8004938c>] (smpboot_thread_fn) from [<80045928>] (kthread+0xdc/0xf8)
[ 8865.089133] r10:00000000 r9:00000000 r8:00000000 r7:8004938c r6:be035740 r5:be035780
[ 8865.097097] r4:00000000 r3:be069380
[ 8865.100752] [<8004584c>] (kthread) from [<8000ed10>] (ret_from_fork+0x14/0x24)
[ 8865.107990] r7:00000000 r6:00000000 r5:8004584c r4:be035780
[ 8865.113767] Code: e320f000 e4913004 e4914004 e4915004 (e4916004)
[ 8865.120006] ---[ end trace b0a4c6bd499288ca ]---
[ 8865.124697] Kernel panic - not syncing: Fatal exception in interrupt
[ 8865.131084] ---[ end Kernel panic - not syncing: Fatal exception in interrupt
Cc: [v3.19+] stable@vger.kernel.org
Tested-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes the backward compatibile of the older driver with the
newer firmware by making the binding unique so that the older driver won't
recognize the non-supported interfaces.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: Keyur Chudgar <kchudgar@apm.com>
Tested-by: Mark Langsdorf <mlangsdo@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case there was some tx buffer reclaimed and not enough rx packets
to consume the whole budget, napi_complete would not be called and
interrupts would be kept disabled, effectively resulting in the
network core never to call the poll callback again and no rx/tx
interrupts to be fired either.
Fix that by only accounting the rx work done in the poll callback.
Signed-off-by: Nicolas Schichan <nschichan@freebox.fr>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently we're getting IRQs after lots of resources are already
allocated:
* netdev
* clocks
* MDIO bus
Also HW gets initialized by the time when checking IRQs as well.
Now there's a possibility for master interrupt controller to be not
probed yet. This will lead to exit from GMAC probe routine with "-
EPROBE_DEFER" and so deferred probe will hapen later on.
But since we exited the first GMAC probe without release of all
allocated resources there could be conflicts on subsequent probes.
For example this is what happens for me:
--->8---
stmmaceth e0018000.ethernet: no reset control found
stmmac - user ID: 0x10, Synopsys ID: 0x37
Ring mode enabled
DMA HW capability register supported
Normal descriptors
RX Checksum Offload Engine supported (type 2)
TX Checksum insertion supported
Enable RX Mitigation via HW Watchdog Timer
libphy: stmmac: probed
eth0: PHY ID 20005c7a at 1 IRQ POLL (stmmac-0:01) active
platform e0018000.ethernet: Driver stmmaceth requests probe deferral
...
...
...
stmmaceth e0018000.ethernet: no reset control found
stmmac - user ID: 0x10, Synopsys ID: 0x37
Ring mode enabled
DMA HW capability register supported
Normal descriptors
RX Checksum Offload Engine supported (type 2)
TX Checksum insertion supported
Enable RX Mitigation via HW Watchdog Timer
------------[ cut here ]------------
WARNING: CPU: 0 PID: 6 at fs/sysfs/dir.c:31 sysfs_warn_dup+0x4e/0x68()
sysfs: cannot create duplicate filename
'/devices/platform/axs10x_mb/e0018000.ethernet/mdio_bus/stmmac-0'
CPU: 0 PID: 6 Comm: kworker/u2:0 Not tainted 4.0.0-rc1-next-20150303+#8
Workqueue: deferwq deferred_probe_work_func
Stack Trace:
arc_unwind_core+0xb8/0x114
warn_slowpath_common+0x5a/0x8c
warn_slowpath_fmt+0x2e/0x38
sysfs_warn_dup+0x4e/0x68
sysfs_create_dir_ns+0x98/0xa0
kobject_add_internal+0x8c/0x2e8
kobject_add+0x4a/0x8c
device_add+0xc6/0x448
mdiobus_register+0x6c/0x164
stmmac_mdio_register+0x112/0x264
stmmac_dvr_probe+0x6c0/0x85c
stmmac_pltfr_probe+0x2e4/0x50c
platform_drv_probe+0x26/0x5c
really_probe+0x76/0x1dc
bus_for_each_drv+0x42/0x7c
device_attach+0x64/0x6c
bus_probe_device+0x74/0xa4
deferred_probe_work_func+0x50/0x84
process_one_work+0xf8/0x2cc
worker_thread+0x110/0x478
kthread+0x8a/0x9c
ret_from_fork+0x14/0x18
---[ end trace a2dfaa7d630c8be1 ]---
------------[ cut here ]------------
WARNING: CPU: 0 PID: 6 at lib/kobject.c:240
kobject_add_internal+0x218/0x2e8()
kobject_add_internal failed for stmmac-0 with -EEXIST, don't try to
register things with the same name in the same di.
CPU: 0 PID: 6 Comm: kworker/u2:0 Tainted: G W
4.0.0-rc1-next-20150303+ #8
Workqueue: deferwq deferred_probe_work_func
Stack Trace:
arc_unwind_core+0xb8/0x114
warn_slowpath_common+0x5a/0x8c
warn_slowpath_fmt+0x2e/0x38
kobject_add_internal+0x218/0x2e8
kobject_add+0x4a/0x8c
device_add+0xc6/0x448
mdiobus_register+0x6c/0x164
stmmac_mdio_register+0x112/0x264
stmmac_dvr_probe+0x6c0/0x85c
stmmac_pltfr_probe+0x2e4/0x50c
platform_drv_probe+0x26/0x5c
really_probe+0x76/0x1dc
bus_for_each_drv+0x42/0x7c
device_attach+0x64/0x6c
bus_probe_device+0x74/0xa4
deferred_probe_work_func+0x50/0x84
process_one_work+0xf8/0x2cc
worker_thread+0x110/0x478
kthread+0x8a/0x9c
ret_from_fork+0x14/0x18
---[ end trace a2dfaa7d630c8be2 ]---
libphy: mii_bus stmmac-0 failed to register
: Cannot register as MDIO bus
stmmac_pltfr_probe: main driver probe failed
stmmaceth: probe of e0018000.ethernet failed with error -22
--->8---
Essential fix is to check for IRQs availability as early as possible and
then safely go to deferred probe if IRQs are not there yet.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Sonic Zhang <sonic.zhang@analog.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking fixes from David Miller:
1) If an IPVS tunnel is created with a mixed-family destination
address, it cannot be removed. Fix from Alexey Andriyanov.
2) Fix module refcount underflow in netfilter's nft_compat, from Pablo
Neira Ayuso.
3) Generic statistics infrastructure can reference variables sitting on
a released function stack, therefore use dynamic allocation always.
Fix from Ignacy Gawędzki.
4) skb_copy_bits() return value test is inverted in ip_check_defrag().
5) Fix network namespace exit in openvswitch, we have to release all of
the per-net vports. From Pravin B Shelar.
6) Fix signedness bug in CAIF's cfpkt_iterate(), from Dan Carpenter.
7) Fix rhashtable grow/shrink behavior, only expand during inserts and
shrink during deletes. From Daniel Borkmann.
8) Netdevice names with semicolons should never be allowed, because
they serve as a separator. From Matthew Thode.
9) Use {,__}set_current_state() where appropriate, from Fabian
Frederick.
10) Revert byte queue limits support in r8169 driver, it's causing
regressions we can't figure out.
11) tcp_should_expand_sndbuf() erroneously uses tp->packets_out to
measure packets in flight, properly use tcp_packets_in_flight()
instead. From Neal Cardwell.
12) Fix accidental removal of support for bluetooth in CSR based Intel
wireless cards. From Marcel Holtmann.
13) We accidently added a behavioral change between native and compat
tasks, wrt testing the MSG_CMSG_COMPAT bit. Just ignore it if the
user happened to set it in a native binary as that was always the
behavior we had. From Catalin Marinas.
14) Check genlmsg_unicast() return valud in hwsim netlink tx frame
handling, from Bob Copeland.
15) Fix stale ->radar_required setting in mac80211 that can prevent
starting new scans, from Eliad Peller.
16) Fix memory leak in nl80211 monitor, from Johannes Berg.
17) Fix race in TX index handling in xen-netback, from David Vrabel.
18) Don't enable interrupts in amx-xgbe driver until all software et al.
state is ready for the interrupt handler to run. From Thomas
Lendacky.
19) Add missing netlink_ns_capable() checks to rtnl_newlink(), from Eric
W Biederman.
20) The amount of header space needed in macvtap was not calculated
properly, fix it otherwise we splat past the beginning of the
packet. From Eric Dumazet.
21) Fix bcmgenet TCP TX perf regression, from Jaedon Shin.
22) Don't raw initialize or mod timers, use setup_timer() and
mod_timer() instead. From Vaishali Thakkar.
23) Fix software maintained statistics in bcmgenet and systemport
drivers, from Florian Fainelli.
24) DMA descriptor updates in sh_eth need proper memory barriers, from
Ben Hutchings.
25) Don't do UDP Fragmentation Offload on RAW sockets, from Michal
Kubecek.
26) Openvswitch's non-masked set actions aren't constructed properly
into netlink messages, fix from Joe Stringer.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (116 commits)
openvswitch: Fix serialization of non-masked set actions.
gianfar: Reduce logging noise seen due to phy polling if link is down
ibmveth: Add function to enable live MAC address changes
net: bridge: add compile-time assert for cb struct size
udp: only allow UFO for packets from SOCK_DGRAM sockets
sh_eth: Really fix padding of short frames on TX
Revert "sh_eth: Enable Rx descriptor word 0 shift for r8a7790"
sh_eth: Fix RX recovery on R-Car in case of RX ring underrun
sh_eth: Ensure proper ordering of descriptor active bit write/read
net/mlx4_en: Disbale GRO for incoming loopback/selftest packets
net/mlx4_core: Fix wrong mask and error flow for the update-qp command
net: systemport: fix software maintained statistics
net: bcmgenet: fix software maintained statistics
rxrpc: don't multiply with HZ twice
rxrpc: terminate retrans loop when sending of skb fails
net/hsr: Fix NULL pointer dereference and refcnt bugs when deleting a HSR interface.
net: pasemi: Use setup_timer and mod_timer
net: stmmac: Use setup_timer and mod_timer
net: 8390: axnet_cs: Use setup_timer and mod_timer
net: 8390: pcnet_cs: Use setup_timer and mod_timer
...
|
|
Commit 6ce29b0e2a04 ("gianfar: Avoid unnecessary reg accesses in adjust_link()")
eliminates unnecessary calls to adjust_link for phy devices which don't support
interrupts and need polling. As part of that work, the 'new_state' local flag,
which was used to reduce logging noise on the console, was eliminated.
Unfortunately, that means that a 'Link is Down' log message will now be
issued continuously if a link is configured as UP, the link state is down,
and the associated phy requires polling. This occurs because priv->oldduplex
is -1 in this case, which always differs from phydev->duplex. In addition,
phydev->speed may also differ from priv->oldspeed. gfar_update_link_state()
is therefore called each time a phy is polled, even if the link state did not
change.
Cc: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a function that will enable changing the MAC address
of an ibmveth interface while it is still running.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Reviewed-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
My previous fix to clear padding of short frames used skb->len as the
DMA length, assuming that skb_padto() extended skb->len to include the
padding. That isn't the case; we need to use skb_put_padto() instead.
(This wasn't immediately obvious because software padding isn't
actually needed on the R-Car H2. We could make it conditional on
which chip is being driven, but it's probably not worth the effort.)
Reported-by: "Violeta Menéndez González" <violeta.menendez@codethink.co.uk>
Fixes: 612a17a54b50 ("sh_eth: Fix padding of short frames on TX")
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit fd9af07c3404ac9ecbd0d859563360f51ce1ffde.
The hardware manual states that the frame error and multicast bits are
copied to bits 9:0 of RD0, not bits 25:16. I've tested that this is
true for RFS1 (CRC error), RFS3 (frame too short), RFS4 (frame too
long) and RFS8 (multicast).
Also adjust a comment to agree with this.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case of RX ring underrun (RDE), we attempt to reset the software
descriptor pointers (dirty_rx and cur_rx) to match where the hardware
will read the next descriptor from, as that might not be the first
dirty descriptor. This relies on reading RDFAR, but that register
doesn't exist on all supported chips - specifically, not on the R-Car
chips. This will result in unpredictable behaviour on those chips
after an RDE.
Make this pointer reset conditional and assume that it isn't needed on
the R-Car chips. This fix also assumes that RDFAR is never exposed at
offset 0 in the memory map - this is currently true, and a subsequent
commit will fix the ambiguity between offset 0 and no-offset in the
register offset maps.
Fixes: 79fba9f51755 ("net: sh_eth: fix the rxdesc pointer when rx ...")
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When submitting a DMA descriptor, the active bit must be written last.
When reading a completed DMA descriptor, the active bit must be read
first.
Add memory barriers to ensure that this ordering is maintained.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Packets which are sent from the selftest (ethtool) flow,
should not be passed to GRO stack but rather dropped by
the driver after validation. To achieve that, we disable
GRO for the duration of the selftest.
Fixes: dd65beac48a5 ("net/mlx4_en: Extend usage of napi_gro_frags")
Reported-by: Carol Soto <clsoto@linux.vnet.ibm.com>
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The bit mask for currently supported driver features (MLX4_UPDATE_QP_SUPPORTED_ATTRS)
of the update-qp command was defined twice (using enum value and pre-processor
define directive) and wrong.
The return value of the call to mlx4_update_qp() from within the SRIOV
resource-tracker was wrongly voided down.
Fix both issues.
issue: none
Fixes: 09e05c3f78e9 ('net/mlx4: Set vlan stripping policy by the right command')
Fixes: ce8d9e0d6746 ('net/mlx4_core: Add UPDATE_QP SRIOV wrapper support')
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 60b4ea1781fd ("net: systemport: log RX buffer allocation and RX/TX DMA
failures") added a few software maintained statistics using
BCM_SYSPORT_STAT_MIB_RX and BCM_SYSPORT_STAT_MIB_TX. These statistics are read
from the hardware MIB counters, such that bcm_sysport_update_mib_counters() was
trying to read from a non-existing MIB offset for these counters.
Fix this by introducing a special type: BCM_SYSPORT_STAT_SOFT, similar to
BCM_SYSPORT_STAT_NETDEV, such that bcm_sysport_get_ethtool_stats will read from
the software mib.
Fixes: 60b4ea1781fd ("net: systemport: log RX buffer allocation and RX/TX DMA failures")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 44c8bc3ce39f ("net: bcmgenet: log RX buffer allocation and RX/TX dma
failures") added a few software maintained statistics using
BCMGENET_STAT_MIB_RX and BCMGENET_STAT_MIB_TX. These statistics are read from
the hardware MIB counters, such that bcmgenet_update_mib_counters() was trying
to read from a non-existing MIB offset for these counters.
Fix this by introducing a special type: BCMGENET_STAT_SOFT, similar to
BCMGENET_STAT_NETDEV, such that bcmgenet_get_ethtool_stats will read from the
software mib.
Fixes: 44c8bc3ce39f ("net: bcmgenet: log RX buffer allocation and RX/TX dma failures")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use timer API functions setup_timer and mod_timer instead
of structure assignments as they are standard way to set
the timer and to update the expire field of an active timer
respectively.
This is done using Coccinelle and semantic patch used for
this is as follows:
// <smpl>
@@
expression x,y,z,a,b;
@@
-init_timer (&x);
+setup_timer (&x, y, z);
+mod_timer (&a, b);
-x.function = y;
-x.data = z;
-x.expires = b;
-add_timer(&a);
// </smpl>
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use timer API functions setup_timer and mod_timer instead
of structure assignments as they are standard way to set
the timer and to update the expire field of an active timer
respectively.
This is done using Coccinelle and semantic patch used for
this is as follows:
// <smpl>
@@
expression x,y,z,a,b;
@@
-init_timer (&x);
+setup_timer (&x, y, z);
+mod_timer (&a, b);
-x.function = y;
-x.data = z;
-x.expires = b;
-add_timer(&a);
// </smpl>
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use timer API functions setup_timer and mod_timer instead
of structure assignments as they are standard way to set
the timer and to update the expire field of an active timer
respectively.
This is done using Coccinelle and semantic patch used for
this is as follows:
// <smpl>
@@
expression x,y,z,a,b;
@@
-init_timer (&x);
+setup_timer (&x, y, z);
+mod_timer (&a, b);
-x.function = y;
-x.data = z;
-x.expires = b;
-add_timer(&a);
// </smpl>
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use timer API functions setup_timer and mod_timer instead
of structure assignments as they are standard way to set
the timer and to update the expire field of an active timer
respectively.
This is done using Coccinelle and semantic patch used for
this is as follows:
// <smpl>
@@
expression x,y,z,a,b;
@@
-init_timer (&x);
+setup_timer (&x, y, z);
+mod_timer (&a, b);
-x.function = y;
-x.data = z;
-x.expires = b;
-add_timer(&a);
// </smpl>
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use timer API functions setup_timer and mod_timer instead
of structure assignments as they are standard way to set
the timer and to update the expire field of an active timer
respectively.
This is done using Coccinelle and semantic patch used for
this is as follows:
// <smpl>
@@
expression x,y,z,a,b;
@@
-init_timer (&x);
+setup_timer (&x, y, z);
+mod_timer (&a, b);
-x.function = y;
-x.data = z;
-x.expires = b;
-add_timer(&a);
// </smpl>
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change 'mutliple' to 'multiple'
Change 'Firmare' to 'Firmware'
Signed-off-by: Yannick Guerrini <yguerrini@tomshardware.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change 'Firmare' to 'Firmware'
Signed-off-by: Yannick Guerrini <yguerrini@tomshardware.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Setting a dev_pm_ops suspend/resume pair but not a set of
hibernation functions means those pm functions will not be
called upon hibernation.
Fix this by using SIMPLE_DEV_PM_OPS, which appropriately
assigns the suspend and hibernation handlers and move
cpsw_suspend/resume calbacks under CONFIG_PM_SLEEP
to avoid build warnings.
Signed-off-by: Grygorii Strashko <Grygorii.Strashko@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Setting a dev_pm_ops suspend_late/resume_early pair but not a
set of hibernation functions means those pm functions will
not be called upon hibernation.
Fix this by using SET_LATE_SYSTEM_SLEEP_PM_OPS, which appropriately
assigns the suspend and hibernation handlers and move
davinci_mdio_x callbacks under CONFIG_PM_SLEEP to avoid build warnings.
Signed-off-by: Grygorii Strashko <Grygorii.Strashko@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 740c7f31c094703c ("sh_eth: Ensure DMA engines are stopped before
freeing buffers") added a call to sh_eth_reset() to the
sh_eth_set_ringparam() and sh_eth_close() paths.
However, setting the software reset bit(s) in the EDMR register resets
the MAC Address Registers to zero. Hence after kexec, the new kernel
doesn't detect a valid MAC address and assigns a random MAC address,
breaking DHCP.
Set the MAC address again after the reset in sh_eth_dev_exit() to fix
this.
Tested on r8a7740/armadillo (GETHER) and r8a7791/koelsch (FAST_RCAR).
Fixes: 740c7f31c094703c ("sh_eth: Ensure DMA engines are stopped before freeing buffers")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds bcmgenet_tx_poll for the tx_rings. This can reduce the
interrupt load and send xmit in network stack on time. This also
separated for the completion of tx_ring16 from bcmgenet_poll.
The bcmgenet_tx_reclaim of tx_ring[{0,1,2,3}] operative by an interrupt
is to be not more than a certain number TxBDs. It is caused by too
slowly reclaiming the transmitted skb. Therefore, performance
degradation of xmit after 605ad7f ("tcp: refine TSO autosizing").
Signed-off-by: Jaedon Shin <jaedon.shin@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Brian reported crashes using IPv6 traffic with macvtap/veth combo.
I tracked the crashes in neigh_hh_output()
-> memcpy(skb->data - HH_DATA_MOD, hh->hh_data, HH_DATA_MOD);
Neighbour code assumes headroom to push Ethernet header is
at least 16 bytes.
It appears macvtap has only 14 bytes available on arches
where NET_IP_ALIGN is 0 (like x86)
Effect is a corruption of 2 bytes right before skb->head,
and possible crashes if accessing non existing memory.
This fix should also increase IPv4 performance, as paranoid code
in ip_finish_output2() wont have to call skb_realloc_headroom()
Reported-by: Brian Rak <brak@vultr.com>
Tested-by: Brian Rak <brak@vultr.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
A few patches have accumulated, among them the fix for Linus's
four-way-handshake problem. The others are various small fixes
for problems all over, nothing really stands out.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Prior to this patch, sending a packet with the source MAC address of one
of the CPSW interfaces to one of the CPSW slave ports while it's configured in
dual_emac mode would update the port_num field of the VLAN/Unicast Address
Table Entry. This would cause it to discard all incoming traffic addressed to
that MAC address, essentially rendering the port useless until the ALE table is
cleared (by starting and stopping the interface or rebooting.)
For example, if eth0 has a MAC address of 90:59:af:8f:43:e9 it will have
an ALE table entry:
00 00 00 00 59 90 02 30 e9 43 8f af
(VLAN Addr vlan_id=2 unicast type=0 port_num=0 addr=90:59:af:8f:43:e9)
If you configure another device with the same MAC address and connect it
to the first CPSW slave port and send some traffic the ALE table entry
becomes:
04 00 00 00 59 90 02 30 e9 43 8f af
(VLAN Addr vlan_id=2 unicast type=0 port_num=1 addr=90:59:af:8f:43:e9)
>From this point forward all incoming traffic addressed to
90:59:af:8f:43:e9 will be dropped.
Setting the SECURE bit for the VLAN/Unicast address table entry for each
interface's MAC address corrects the problem.
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is a discrepancy here because the niu_class_to_ethflow() returns
zero on failure and one on success but the caller expected zero on
success and negative on failure.
The problem means that we allow the user to pass classes and flow_types
which we don't want. I've looked at it a bit and I don't see it as a
very serious bug.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The smc91x driver traditionally gets configured at compile-time
for whichever hardware it runs on. This no longer works on
ARM as we continue to move to building all-in-one kernels.
Most ARM configurations with this driver already use run-time
configuration through DT or through platform_data, but a
few have not been converted yet.
I've checked all ARM boards that use this driver in their
legacy board files, and converted the ones that were using
compile-time configuration in smc91x.h to behave like the
other ones and provide the interrupt polarity along with
the MMIO configuration (width, stride) at platform device
creation time.
In particular, these combinations were previously selectable
in Kconfig but in fact broken:
- sa1100 assabet plus pleb
- msm combined with any other armv6/v7 platform
- pxa-idp combined with any non-DMA pxa variant
- LogicPD PXA270 combined with any other pxa
- nomadik combined with any other armv4/v5 platform,
e.g. versatile.
None of these seem critical enough to warrant a backport
to stable, but it would be nice to clean this up for good.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
----
I would like the patch to get merged through netdev, after
Robert and/or Linus have verified it on at least some hardware.
There are a few other non-ARM platforms using this driver,
I could do the same patch for those if we want to take
it further.
arch/arm/mach-msm/board-halibut.c | 8 ++++-
arch/arm/mach-msm/board-qsd8x50.c | 8 ++++-
arch/arm/mach-pxa/idp.c | 5 +++
arch/arm/mach-pxa/lpd270.c | 8 ++++-
arch/arm/mach-realview/core.c | 7 ++++
arch/arm/mach-realview/realview_eb.c | 2 +-
arch/arm/mach-sa1100/neponset.c | 6 ++++
arch/arm/mach-sa1100/pleb.c | 7 ++++
drivers/net/ethernet/smsc/smc91x.c | 9 +++--
drivers/net/ethernet/smsc/smc91x.h | 114 ++----------------------------------------------------------
10 files changed, 57 insertions(+), 117 deletions(-)
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2015-02-26
This series contains fixes for i40e and i40evf only.
Alexey Khoroshilov found a possible leak of 'cmd_buf' when copy_from_user()
failed in i40e_dbg_command_write(), so resolved by calling kfree().
Shannon provides a fix to ensure the shift and bitwise precedences do not
work backwards for us by adding parans. Fixed the driver by preventing
the driver from allowing stray interrupts or causing system logs from
un-handled interrupts by combining the ICR0 shutdown with the standard
interrupt shutdown and add the interrupt clearing to the PCI shutdown
path. Fixed an issue where a NVM write times out before a transaction
can complete, so Shannon added logic to make another attempt by
reacquiring the semaphore, then retry the write, if the one retry fails,
we will then give up. Adds checks to pointers before their use to ensure
we do not try to dereference NULL pointers when returning values from the
AdminQ calls.
Akeem adds a check to bail out if the device is already down when checking
for Tx hang subtask.
Anjali fixes TSO with more than 8 frags per segment issue. The hardware
has some limitations which the driver needs to adhere to:
1) no more than 8 descriptors per packet on the wire
2) no header can span more than 3 descriptors
If one of these events happens, the hardware will generate an internal
error and freeze the Tx queue, so Anjali fixes this by linearizes the skb
to avoid these situations. Fixed an issue where the per Traffic Class
queue count was higher than queues enabled, which will fix a warning
with multiple function mode where systems regularly have more cores than
vectors. Fixed TCP/IPv6 over VXLAN Tx checksum offload, where we were
checking the outer protocol flags and deciding the flow for the inner
header.
Jesse fixes a race condition in the transmit hang detection. Before we
were having issues of false Tx hang detection, no the driver makes more
direct with the checks for progress forward by directly checking the head
write back address and tail register when determining progress. This
avoids Tx hangs where the software gets behind, because we are directly
checking hardware state when determining a hang state.
Neerav fixes the transmit ring Qset handle when DCB reconfigures. The issue
was when DCB is reconfigured to a single traffic class (TC) and the driver
did not reset the Tx ring Qset handle to correct the mapping, which caused
the Tx queue to disable timeouts. Also as part of DCB reconfiguration flow
if the Tx queue disable times out, then issue a PF reset to do some level
of recovery.
Mitch stops flow director on shutdown because, in some cases, the hardware
would continue to try to access the FDIR ring after entering D3Hot state,
which would cause either PCIe errors or NMIs, depending upon the system
configuration.
* NOTE * I have verified that this series of patches for net will not cause
any merge issues when you sync up your net tree with your net-next tree.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It is possible that the hardware may not have been properly shutdown
before this driver gets control, through use by firmware, for example.
Until the driver is loaded, interrupts associated with the hardware
could go pending. When the IRQs are requested napi support has not
been initialized yet, but the ISR will get control and schedule napi
processing resulting in a kernel panic because the poll routine has not
been set.
Adjust the code so that the driver is fully ready to handle and process
interrupts as soon as the IRQs are requested. This involves requesting
and freeing IRQs during start and stop processing and ordering the napi
add and delete calls appropriately.
Also adjust the powerup and powerdown routines to match the start and
stop routines in regards to the ordering of tasks, including napi
related calls.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
Josh Cartwright
Ahmed S. Darwish
Stephane Grosjean
Oliver Hartkopp
Peter Senna Tschudin
Stefan Agner
Punnaiah Choudary Kalluri
Tobias Waldekranz
Florian Fainelli
Mark Salter
Brian King
David Vrabel
Arnd Bergmann
Jiri Pirko
Fugang Duan
Iyappan Subramanian
Nicolas Schichan
Alexey Brodkin
Linus Torvalds
Guenter Roeck
Thomas Falcon
Ben Hutchings
Ido Shamay
Or Gerlitz
Vaishali Thakkar
Yannick Guerrini
Grygorii Strashko
Geert Uytterhoeven
Jaedon Shin
Eric Dumazet
David S. Miller
George McCollister
Dan Carpenter
Lendacky, Thomas