| Age | Commit message (Collapse) | Author |
|---|
|
Pull networking updates from David Miller:
"More bug fixes, nothing gets past these guys"
1) More kernel info leaks found by Mathias Krause, this time in the
IPSEC configuration layers.
2) When IPSEC policies change, we do not properly make sure that cached
routes (which could now be stale) throughout the system will be
revalidated. Fix this by generalizing the generation count
invalidation scheme used by ipv4. From Nicolas Dichtel.
3) When repairing TCP sockets, we need to allow to restore not just the
send window scale, but the receive one too. Extend the existing
interface to achieve this in a backwards compatible way. From
Andrey Vagin.
4) A fix for FCOE scatter gather feature validation erroneously caused
scatter gather to be disabled for things like AOE too. From Ed L
Cashin.
5) Several cases of mishandling of error pointers, from Mathias Krause,
Wei Yongjun, and Devendra Naga.
6) Fix gianfar build, from Richard Cochran.
7) CAP_NET_* failures should return -EPERM not -EACCES, from Zhao
Hongjiang.
8) Hardware reset fix in janz-ican3 CAN driver, from Ira W Snyder.
9) Fix oops during rmmod in ti_hecc CAN driver, from Marc Kleine-Budde.
10) The removal of the conditional compilation of the clk support code
in the stmmac driver broke things. This is because the interfaces
used are the ones that don't also perform the enable/disable of the
clk. Fix from Stefan Roese.
11) The QFQ packet scheduler can record out of range virtual start
times, resulting later in misbehavior and even crashes. Fix from
Paolo Valente.
12) If MSG_WAITALL is used with IOAT DMA under TCP, we can wedge the
receiver when the advertised receive window goes to zero. Detect
this case and force the processing of the IOAT DMA queue when it
happens to avoid getting stuck. Fix from Michal Kubecek.
13) batman-adv assumes that test_bit() returns only 0 or 1, but this is
not true for x86 (which returns -1 or 0, via the 'sbb' instruction).
Fix from Linus Lussing.
14) Fix small packet corruption in e1000, from Tushar Dave.
15) make_blackhole() in the IPSEC policy code can do one read unlock too
many, fix from Li RongQing.
16) The new tcp_try_coalesce() code introduced a bug in TCP URG
handling, fix from Eric Dumazet.
17) Fix memory leak in __netif_receive_skb() when doing zerocopy and
when hit an OOM condition. From Michael S Tsirkin.
18) netxen blindly deferences pdev->bus->self, which is not guarenteed
to be non-NULL. Fix from Nikolay Aleksandrov.
19) Fix a performance regression caused by mistakes in ipv6 checksum
validation in the bnx2x driver, fix from Michal Schmidt.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (45 commits)
net/stmmac: Use clk_prepare_enable and clk_disable_unprepare
net: change return values from -EACCES to -EPERM
net/irda: sh_sir: fix return value check in sh_sir_set_baudrate()
stmmac: fix return value check in stmmac_open_ext_timer()
gianfar: fix phc index build failure
ipv6: fix return value check in fib6_add()
bnx2x: remove false warning regarding interrupt number
can: ti_hecc: fix oops during rmmod
can: janz-ican3: fix support for older hardware revisions
net: do not disable sg for packets requiring no checksum
aoe: assert AoE packets marked as requiring no checksum
at91ether: return PTR_ERR if call to clk_get fails
xfrm_user: don't copy esn replay window twice for new states
xfrm_user: ensure user supplied esn replay window is valid
xfrm_user: fix info leak in copy_to_user_tmpl()
xfrm_user: fix info leak in copy_to_user_policy()
xfrm_user: fix info leak in copy_to_user_state()
xfrm_user: fix info leak in copy_to_user_auth()
net: qmi_wwan: adding Huawei E367, ZTE MF683 and Pantech P4200
tcp: restore rcv_wscale in a repair mode (v2)
...
|
|
This patch fixes an issue introduced by commit ID 6a81c26f
[net/stmmac: remove conditional compilation of clk code], which
switched from the internal stmmac_clk_{en}{dis}able calls to
clk_{en}{dis}able. By this, calling clk_prepare and clk_unprepare
was removed.
clk_{un}prepare is mandatory for platforms using common clock framework.
Since these drivers are used by SPEAr platform, which supports common
clock framework, add clk_{un}prepare() support for them. Otherwise
the clocks are not correctly en-/disabled and ethernet support doesn't
work.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Marc Kleine-Budde says:
====================
two patches for the v3.6 release cycle. Ira W. Snyder fixed support for the
older version of the Janz CMOD-IO Carrier Board. I found and fixed an oops in
the ti_hecc driver, which occurs when removing the module if the network
interface is still open.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case of error, the function clk_get() returns ERR_PTR()
and never returns NULL pointer. The NULL test in the error
handling should be replaced with IS_ERR().
dpatch engine is used to auto generated this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case of error, the function clk_get() returns ERR_PTR()
and never returns NULL pointer. The NULL test in the error
handling should be replaced with IS_ERR().
dpatch engine is used to auto generated this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes a build failure introduced in commit 66636287
("gianfar: Support the get_ts_info ethtool method."). Not only was a
global variable inconsistently named, but also it was not exported as
it should have been.
This fix is also needed in stable version 3.5.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since version 7.4 the FW configures in the pci config space the max
number of interrupts available to the physical function, instead of
the exact number to use.
This causes a false warning in driver when comparing the number of
configured interrupts to the number about to be used.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes an oops which occurs when unloading the driver, while the
network interface is still up. The problem is that first the io mapping is
teared own, then the CAN device is unregistered, resulting in accessing the
hardware's iomem:
[ 172.744232] Unable to handle kernel paging request at virtual address c88b0040
[ 172.752441] pgd = c7be4000
[ 172.755645] [c88b0040] *pgd=87821811, *pte=00000000, *ppte=00000000
[ 172.762207] Internal error: Oops: 807 [#1] PREEMPT ARM
[ 172.767517] Modules linked in: ti_hecc(-) can_dev
[ 172.772430] CPU: 0 Not tainted (3.5.0alpha-00037-g3554cc0 #126)
[ 172.778961] PC is at ti_hecc_close+0xb0/0x100 [ti_hecc]
[ 172.784423] LR is at __dev_close_many+0x90/0xc0
[ 172.789123] pc : [<bf00c768>] lr : [<c033be58>] psr: 60000013
[ 172.789123] sp : c5c1de68 ip : 00040081 fp : 00000000
[ 172.801025] r10: 00000001 r9 : c5c1c000 r8 : 00100100
[ 172.806457] r7 : c5d0a48c r6 : c5d0a400 r5 : 00000000 r4 : c5d0a000
[ 172.813232] r3 : c88b0000 r2 : 00000001 r1 : c5d0a000 r0 : c5d0a000
[ 172.820037] Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user
[ 172.827423] Control: 10c5387d Table: 87be4019 DAC: 00000015
[ 172.833404] Process rmmod (pid: 600, stack limit = 0xc5c1c2f0)
[ 172.839447] Stack: (0xc5c1de68 to 0xc5c1e000)
[ 172.843994] de60: bf00c6b8 c5c1dec8 c5d0a000 c5d0a000 00200200 c033be58
[ 172.852478] de80: c5c1de44 c5c1dec8 c5c1dec8 c033bf2c c5c1de90 c5c1de90 c5d0a084 c5c1de44
[ 172.860992] dea0: c5c1dec8 c033c098 c061d3dc c5d0a000 00000000 c05edf28 c05edb34 c000d724
[ 172.869476] dec0: 00000000 c033c2f8 c5d0a084 c5d0a084 00000000 c033c370 00000000 c5d0a000
[ 172.877990] dee0: c05edb00 c033c3b8 c5d0a000 bf00d3ac c05edb00 bf00d7c8 bf00d7c8 c02842dc
[ 172.886474] df00: c02842c8 c0282f90 c5c1c000 c05edb00 bf00d7c8 c0283668 bf00d7c8 00000000
[ 172.894989] df20: c0611f98 befe2f80 c000d724 c0282d10 bf00d804 00000000 00000013 c0068a8c
[ 172.903472] df40: c5c538e8 685f6974 00636365 c61571a8 c5cb9980 c61571a8 c6158a20 c00c9bc4
[ 172.911987] df60: 00000000 00000000 c5cb9980 00000000 c5cb9980 00000000 c7823680 00000006
[ 172.920471] df80: bf00d804 00000880 c5c1df8c 00000000 000d4267 befe2f80 00000001 b6d90068
[ 172.928985] dfa0: 00000081 c000d5a0 befe2f80 00000001 befe2f80 00000880 b6d90008 00000008
[ 172.937469] dfc0: befe2f80 00000001 b6d90068 00000081 00000001 00000000 befe2eac 00000000
[ 172.945983] dfe0: 00000000 befe2b18 00023ba4 b6e6addc 60000010 befe2f80 a8e00190 86d2d344
[ 172.954498] [<bf00c768>] (ti_hecc_close+0xb0/0x100 [ti_hecc]) from [<c033be58>] (__dev__registered_many+0xc0/0x2a0)
[ 172.984161] [<c033c098>] (rollback_registered_many+0xc0/0x2a0) from [<c033c2f8>] (rollback_registered+0x20/0x30)
[ 172.994750] [<c033c2f8>] (rollback_registered+0x20/0x30) from [<c033c370>] (unregister_netdevice_queue+0x68/0x98)
[ 173.005401] [<c033c370>] (unregister_netdevice_queue+0x68/0x98) from [<c033c3b8>] (unregister_netdev+0x18/0x20)
[ 173.015899] [<c033c3b8>] (unregister_netdev+0x18/0x20) from [<bf00d3ac>] (ti_hecc_remove+0x60/0x80 [ti_hecc])
[ 173.026245] [<bf00d3ac>] (ti_hecc_remove+0x60/0x80 [ti_hecc]) from [<c02842dc>] (platform_drv_remove+0x14/0x18)
[ 173.036712] [<c02842dc>] (platform_drv_remove+0x14/0x18) from [<c0282f90>] (__device_release_driver+0x7c/0xbc)
Cc: stable <stable@vger.kernel.org>
Cc: Anant Gole <anantgole@ti.com>
Tested-by: Jan Luebbe <jlu@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The Revision 1.0 Janz CMOD-IO Carrier Board does not have support for
the reset registers. To support older hardware, the code is changed to
use the hardware reset register on the Janz VMOD-ICAN3 hardware itself.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
we are currently returning ENODEV, as the clk_get may give a exact
error code in its returned pointer, assign it to the ret by using the
PTR_ERR function, so that the subsequent goto label will jump to the
error path and clean the driver and return the error correctly.
Signed-off-by: Devendra Naga <devendra.aaru@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
One of the modes of Huawei E367 has this QMI/wwan interface:
I:* If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=07 Driver=(none)
E: Ad=83(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
Huawei use subclass and protocol to identify vendor specific
functions, so adding a new vendor rule for this combination.
The Pantech devices UML290 (106c:3718) and P4200 (106c:3721) use
the same subclass to identify the QMI/wwan function. Replace the
existing device specific UML290 entries with generic vendor matching,
adding support for the Pantech P4200.
The ZTE MF683 has 6 vendor specific interfaces, all using
ff/ff/ff for cls/sub/prot. Adding a match on interface #5 which
is a QMI/wwan interface.
Cc: Fangxiaozhi (Franko) <fangxiaozhi@huawei.com>
Cc: Thomas Schäfer <tschaefer@t-online.de>
Cc: Dan Williams <dcbw@redhat.com>
Cc: Shawn J. Goff <shawn7400@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Søren Holm <sgh@sgh.dk>
Cc: stable@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On PCI/PCI-X HW, if packet size is less than ETH_ZLEN,
packets may get corrupted during padding by HW.
To WA this issue, pad all small packets manually.
Signed-off-by: Tushar Dave <tushar.n.dave@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a check if pdev->bus->self == NULL (root bus). When attaching
a netxen NIC to a VM it can be on the root bus and the guest would
crash in netxen_mask_aer_correctable() because of a NULL pointer
dereference if CONFIG_PCIEAER is present.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit d6cb3e41 "bnx2x: fix checksum validation" caused a performance
regression for IPv6. Rx checksum offload does not work. IPv6 packets
are passed to the stack with CHECKSUM_NONE.
The hardware obviously cannot perform IP checksum validation for IPv6,
because there is no checksum in the IPv6 header. This should not prevent
us from setting CHECKSUM_UNNECESSARY.
Tested on BCM57711.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull InfiniBand/RDMA fixes from Roland Dreier:
- A couple more IPoIB fixes for regressions introduced by path database
conversion
- Minor other fixes to low-level drivers (cxgb4, mlx4, qib, ocrdma)
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/qib: Fix failure of compliance test C14-024#06_LocalPortNum
RDMA/ocrdma: Fix CQE expansion of unsignaled WQE
mlx4_core: Fix integer overflows so 8TBs of memory registration works
IPoIB: Fix AB-BA deadlock when deleting neighbours
IPoIB: Fix memory leak in the neigh table deletion flow
RDMA/cxgb4: Move dereference below NULL test
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem
|
|
This patch adds on the fixes done in commits 89dd86db78e0 ("mlx4_core:
Allow large mlx4_buddy bitmaps") and 3de819e6b642 ("mlx4_core: Fix
integer overflow issues around MTT table") so that memory registration
of up to 8TB (log_num_mtt=31) finally works.
It fixes integer overflows in a few mlx4_table_yyy routines in icm.c
by using a u64 intermediate variable, and int/uint issues that caused
table indexes to become nagive by setting some variables to be u32
instead of int. These problems cause crashes when a user attempted to
register > 512GB of RAM.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
Commit a334872224a67b614dc888460377862621f3dac7 added afex support but lacked
several logical changes. This lack can cause afex to crash, and also
have a slight effect on other flows (i.e., driver always assumes the Tx ring
has less available buffers than what it actually has).
This patch adds the missing segments, fixing said issues.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Barak Witkowski <barak@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Under traffic, there are several registers that when read (e.g., via
'ethtool -d') may cause the chip to stall.
This patch corrects the registers read in such flows.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch propagates users' requested flow-control into the link layer,
which will later be used to advertise this flow-control for auto-negotiation
(until now these values were ignored).
Signed-off-by: Yaniv Rosner <yaniv.rosner@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Prior to this fix, the driver reported the chip's active duplex state
is always 'full', even if using half-duplex mode.
Signed-off-by: Yaniv Rosner <yaniv.rosner@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Prevent updating the xmac PFC configuration when using a link speed
slower than 10G -the umac block is responsible for 1G or slower connections,
therefore it is possible the xmac block is reset when connection is slower.
Signed-off-by: Yaniv Rosner <yaniv.rosner@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
FW needs the driver statistics for management. Current logic is broken
in that the function that gathers the port statistics does not copy
its own statistics to a place where the FW can use it.
This patch causes every function that can pass statistics to the FW to
do so.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
During traffic when DCB is enabled, it is possible for multiple instances
of statistics queries to be sent to the chip - this may cause the FW to assert.
This patch prevents the sending of an additional instance of statistics query
while the previous query hasn't completed.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This fixes a hang on suspend due to calling wdm_suspend on
the unregistered data interface. The hang should have been
a NULL pointer reference had it not been for a logic error
in the cdc_wdm code.
commit 230718bd net: qmi_wwan: bind to both control and data interface
changed qmi_wwan to use cdc_wdm as a subdriver for devices with
a two-interface QMI/wwan function. The commit failed to update
qmi_wwan_suspend and qmi_wwan_resume, which were written to handle
either a single combined interface function, or no subdriver at all.
The result was that we called into the subdriver both when the
control interface was suspended and when the data interface was
suspended. Calling the subdriver suspend function with an
unregistered interface is not supported and will make the
subdriver bug out.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixes big endian host configuration parameters.
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
ssid len is 32 bit and needs endian conversion for big endian systems.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
There are a number of problems that occur for the latest version
of the Realtek RTL8188CE device with the in-kernel driver. These
include selection of the wrong firmware, and system lockup. A full
fix is known, but is too invasive for inclusion in stable. This patch
fixes the problem with loading the wrong firmware, and logs a message
that the device may not work for kernels 3.6 and older.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Cc: Anisse Astier <anisse@astier.eu>
Cc: Li Chaoming <chaoming_li@realsil.com.cn>
Tested-by: Anisse Astier <anisse@astier.eu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
HP un2430 is a Gobi 3000 device. It was mistakenly treated as Gobi 1000
in patch b9f90eb2740203ff2592efe640409ad48335d1c2.
I own this device and qmi_wwan works again with this fix.
Signed-off-by: Pierre Sauter <pierre.sauter@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 36a1211970193ce215de50ed1e4e1272bc814df1 (netprio_cgroup.h:
dont include module.h from other includes) made the following build
error on ixp4xx_hss pop up:
CC [M] drivers/net/wan/ixp4xx_hss.o
drivers/net/wan/ixp4xx_hss.c:1412:20: error: expected ';', ',' or ')'
before string constant
drivers/net/wan/ixp4xx_hss.c:1413:25: error: expected ';', ',' or ')'
before string constant
drivers/net/wan/ixp4xx_hss.c:1414:21: error: expected ';', ',' or ')'
before string constant
drivers/net/wan/ixp4xx_hss.c:1415:19: error: expected ';', ',' or ')'
before string constant
make[8]: *** [drivers/net/wan/ixp4xx_hss.o] Error 1
This was previously hidden because ixp4xx_hss includes linux/hdlc.h which
includes linux/netdevice.h which includes linux/netprio_cgroup.h which
used to include linux/module.h. The real issue was actually present since
the initial commit that added this driver since it uses macros from
linux/module.h without including this file.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
I discovered I couldn't get sierra_net to work on a powerpc. Turns out
the firmware attribute check assumes the system is little endian and
hence fails because the attributes is a 16 bit value.
Signed-off-by: Len Sorensen <lsorense@csclub.uwaterloo.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Check for oobirq_entry allocation failure to avoid
NULL pointer dereferencing.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Some checks for PA linearization support checked ATH9K_HW_CAP_PAPRD and some
used the EEPROM ops, leading to issues in tx power handling, since those
two can be out of sync.
Disable the feature by default, since it has been reported that it can
cause damage to the rx path under some circumstances. It can now be enabled
for testing via debugfs.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The driver provides the cfg80211 regulatory framework with a set of
custom rules. However, there was a mismatch in number of rules
and the actual rules provided. This resulted in setting an invalid
power level:
ieee80211 phy0: brcms_ops_config: change channel 13
ieee80211 phy0: brcms_ops_config: Error setting power_level (8758364)
Closer look in cfg80211 regulatory blurb showed following bogus rule:
cfg80211: 0 KHz - -60446948 KHz @ 875836468 KHz), (875836468 mBi, 875836468 mBm)
Cc: Seth Forshee <seth.forshee@canonical.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem
John W. Linville says:
====================
Please pull these fixes intended for 3.6. There are more commits
here than I would like -- I got a bit behind while I was stalking
Steven Rostedt in San Diego last week... I'll slow it down after this!
There are a couple of pulls here. One is from Johannes:
"Please pull (according to the below information) to get a few fixes.
* a fix to properly disconnect in the driver when authentication or
association fails
* a fix to prevent invalid information about mesh paths being reported
to userspace
* a memory leak fix in an nl80211 error path"
The other comes via Gustavo:
"A few updates for the 3.6 kernel. There are two btusb patches to add
more supported devices through the new USB_VENDOR_AND_INTEFACE_INFO()
macro and another one that add a new device id for a Sony Vaio laptop,
one fix for a user-after-free and, finally, two patches from Vinicius
to fix a issue in SMP pairing."
Along with those...
Arend van Spriel provides a fix for a use-after-free bug in brcmfmac.
Daniel Drake avoids a hang by not trying to touch the libertas hardware
duing suspend if it is already powered-down.
Felix Fietkau provides a batch of ath9k fixes that adress some
potential problems with power settings, as well as a fix to avoid a
potential interrupt storm.
Gertjan van Wingerde provides a register-width fix for rt2x00, and
a rt2x00 fix to prevent incorrectly detecting the rfkill status.
He also provides a device ID patch.
Hante Meuleman gives us three brcmfmac fixes, one that properly
initializes a command structure, one that fixes a race condition that
could lose usb requests, and one that removes some log spam.
Marc Kleine-Budde offers an rt2x00 fix for a voltage setting on some
specific devices.
Mohammed Shafi Shajakhan sent an ath9k fix to avoid a crash related to
using timers that aren't allocated when 2 wire bluetooth coexistence
hardware is in use.
Sergei Poselenov changes rt2800usb to do some validity checking for
received packets, avoiding crashes on an ARM Soc.
Stone Piao gives us an mwifiex fix for an incorrectly set skb length
value for a command buffer.
All of these are localized to their specific drivers, and relatively
small. The power-related patches from Felix are bigger than I would
like, but I merged them in consideration of their isolation to ath9k
and the sensitive nature of power settings in wireless devices.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It doesn't seem this spinlock was properly initialized.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If mlx4_cmd_init() failed, the init_one function returned
success, although no resources were opened.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The order of operations was wrong on the teardown flow.
Signed-off-by: Aviad Yehezkel <aviadye@mellanox.com>
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The search for promisc entries was always done on the first port,
While the addition is done on the correct port.
This lead to resource leackage of promisc entries on the second
port and brought to a state where we could no longer enter to
promiscuous mode after enough iterations of "ifconfig promisc"
on the second port.
Fix that by using the correct port when searching.
Reported-by: Marcelo Ricardo Leitner <mleitner@redhat.com>
Signed-off-by: Aviad Yehezkel <aviadye@mellanox.com>
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
for VMs
Since VFs may be mapped to VMs which aren't trusted entities, flow
steering rules attached through the wrapper on behalf of VFs must be
checked to make sure that their L2 specification relate to MAC address
assigned to that VF, and add L2 specification if its missing.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To allow for usage of the flow steering Firmware structures in more locations over the driver,
such as the resource tracker, move them from mcg.c to common header files.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes a bug found by Nish Aravamudan
(https://lkml.org/lkml/2012/5/15/220) where the driver is not following
the spec (it is not aligning the rx buffer on a 16-byte boundary) and the
hypervisor aborts the registration, making the device unusable.
The fix follows BenH's recommendation (https://lkml.org/lkml/2012/7/20/461)
to replace the kmalloc+map for a single call to dma_alloc_coherent()
because that function always aligns to a 16-byte boundary.
The stable trees will run into this bug whenever the rx buffer kmalloc call
returns something not aligned on a 16-byte boundary.
Cc: <stable@vger.kernel.org>
Signed-off-by: Santiago Leon <santil@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Marc Kleine-Budde says:
====================
this patch is for the v3.6 release cycle. Benoît Locher fixed a repeated frame
bug in the mcp251x driver. He implemented the workaround suggested by the
errata sheet.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the interface is down, the hardware is powered off.
However, the suspend handler currently tries to send host sleep commands
(when wakeup params are set) in this configuration, causing a system hang
when going into suspend (the commands will never complete).
Avoid this by detecting this situation and simply returning from
the suspend handler without doing anything special.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
On our system (ARM Cortex-M3 SOC running linux-2.6.33)
frequent crashes were observed in the rt2800usb module
because of the invalid length of the received packet (3392,
46920...). This patch adds the sanity check on the packet
legth. Also, changed WARNING to ERROR in rt2x00lib_rxdone()
so that the bad packet condition would be noticed.
The fix was tested on the latest compat-wireless-3.5.1-1-snpc.
Cc: stable@vger.kernel.org
Signed-off-by: Sergei Poselenov <sposelenov@emcraft.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
We need to program the rfkill switch GPIO pin direction to input at
device initialization time, not only when the interface is brought up.
Doing this only when the interface is brought up could lead to rfkill
detecting the switch is turned on erroneously and inability to create
the interface and bringing it up.
Reported-and-tested-by: Andreas Messer <andi@bastelmap.de>
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Cc: <stable@vger.kernel.org>
Acked-by: Ivo Van Doorn <ivdoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The register is 16 bits wide, not 32.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Cc: <stable@vger.kernel.org>
Acked-by: Ivo Van Doorn <ivdoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This is an RT3572 based device.
Signed-off-by: Maximilian Engelhardt <maxi@daemonizer.de>
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Cc: <stable@vger.kernel.org>
Acked-by: Ivo Van Doorn <ivdoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The function brcmf_cfg80211_get_station requests the RSSI from
the device. The complete structure used needs to be cleared
before sending the request to firmware. Otherwise the request
fails filling the logs with "Could not get rssi (-2)" messages.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
Linus Torvalds
Stefan Roese
David S. Miller
Wei Yongjun
Richard Cochran
Ariel Elior
Marc Kleine-Budde
Ira W. Snyder
Devendra Naga
Bjørn Mork
Søren holm
Tushar Dave
Nikolay Aleksandrov
Michal Schmidt
John W. Linville
Yishai Hadas
Yuval Mintz
Dmitry Kravkov
Yaniv Rosner
Hante Meuleman
Larry Finger
Pierre Sauter
Florian Fainelli
Lennart Sorensen
Colin Ian King
Felix Fietkau
Arend van Spriel
Jean Delvare
Eugenia Emantayev
Aviad Yehezkel
Hadar Hen Zion
Santiago Leon
Daniel Drake
Sergei Poselenov
Gertjan van Wingerde