| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem
|
|
Fixes big endian host configuration parameters.
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
ssid len is 32 bit and needs endian conversion for big endian systems.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
There are a number of problems that occur for the latest version
of the Realtek RTL8188CE device with the in-kernel driver. These
include selection of the wrong firmware, and system lockup. A full
fix is known, but is too invasive for inclusion in stable. This patch
fixes the problem with loading the wrong firmware, and logs a message
that the device may not work for kernels 3.6 and older.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Cc: Anisse Astier <anisse@astier.eu>
Cc: Li Chaoming <chaoming_li@realsil.com.cn>
Tested-by: Anisse Astier <anisse@astier.eu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Check for oobirq_entry allocation failure to avoid
NULL pointer dereferencing.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Some checks for PA linearization support checked ATH9K_HW_CAP_PAPRD and some
used the EEPROM ops, leading to issues in tx power handling, since those
two can be out of sync.
Disable the feature by default, since it has been reported that it can
cause damage to the rx path under some circumstances. It can now be enabled
for testing via debugfs.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The driver provides the cfg80211 regulatory framework with a set of
custom rules. However, there was a mismatch in number of rules
and the actual rules provided. This resulted in setting an invalid
power level:
ieee80211 phy0: brcms_ops_config: change channel 13
ieee80211 phy0: brcms_ops_config: Error setting power_level (8758364)
Closer look in cfg80211 regulatory blurb showed following bogus rule:
cfg80211: 0 KHz - -60446948 KHz @ 875836468 KHz), (875836468 mBi, 875836468 mBm)
Cc: Seth Forshee <seth.forshee@canonical.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem
John W. Linville says:
====================
Please pull these fixes intended for 3.6. There are more commits
here than I would like -- I got a bit behind while I was stalking
Steven Rostedt in San Diego last week... I'll slow it down after this!
There are a couple of pulls here. One is from Johannes:
"Please pull (according to the below information) to get a few fixes.
* a fix to properly disconnect in the driver when authentication or
association fails
* a fix to prevent invalid information about mesh paths being reported
to userspace
* a memory leak fix in an nl80211 error path"
The other comes via Gustavo:
"A few updates for the 3.6 kernel. There are two btusb patches to add
more supported devices through the new USB_VENDOR_AND_INTEFACE_INFO()
macro and another one that add a new device id for a Sony Vaio laptop,
one fix for a user-after-free and, finally, two patches from Vinicius
to fix a issue in SMP pairing."
Along with those...
Arend van Spriel provides a fix for a use-after-free bug in brcmfmac.
Daniel Drake avoids a hang by not trying to touch the libertas hardware
duing suspend if it is already powered-down.
Felix Fietkau provides a batch of ath9k fixes that adress some
potential problems with power settings, as well as a fix to avoid a
potential interrupt storm.
Gertjan van Wingerde provides a register-width fix for rt2x00, and
a rt2x00 fix to prevent incorrectly detecting the rfkill status.
He also provides a device ID patch.
Hante Meuleman gives us three brcmfmac fixes, one that properly
initializes a command structure, one that fixes a race condition that
could lose usb requests, and one that removes some log spam.
Marc Kleine-Budde offers an rt2x00 fix for a voltage setting on some
specific devices.
Mohammed Shafi Shajakhan sent an ath9k fix to avoid a crash related to
using timers that aren't allocated when 2 wire bluetooth coexistence
hardware is in use.
Sergei Poselenov changes rt2800usb to do some validity checking for
received packets, avoiding crashes on an ARM Soc.
Stone Piao gives us an mwifiex fix for an incorrectly set skb length
value for a command buffer.
All of these are localized to their specific drivers, and relatively
small. The power-related patches from Felix are bigger than I would
like, but I merged them in consideration of their isolation to ath9k
and the sensitive nature of power settings in wireless devices.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the interface is down, the hardware is powered off.
However, the suspend handler currently tries to send host sleep commands
(when wakeup params are set) in this configuration, causing a system hang
when going into suspend (the commands will never complete).
Avoid this by detecting this situation and simply returning from
the suspend handler without doing anything special.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
On our system (ARM Cortex-M3 SOC running linux-2.6.33)
frequent crashes were observed in the rt2800usb module
because of the invalid length of the received packet (3392,
46920...). This patch adds the sanity check on the packet
legth. Also, changed WARNING to ERROR in rt2x00lib_rxdone()
so that the bad packet condition would be noticed.
The fix was tested on the latest compat-wireless-3.5.1-1-snpc.
Cc: stable@vger.kernel.org
Signed-off-by: Sergei Poselenov <sposelenov@emcraft.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
We need to program the rfkill switch GPIO pin direction to input at
device initialization time, not only when the interface is brought up.
Doing this only when the interface is brought up could lead to rfkill
detecting the switch is turned on erroneously and inability to create
the interface and bringing it up.
Reported-and-tested-by: Andreas Messer <andi@bastelmap.de>
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Cc: <stable@vger.kernel.org>
Acked-by: Ivo Van Doorn <ivdoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The register is 16 bits wide, not 32.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Cc: <stable@vger.kernel.org>
Acked-by: Ivo Van Doorn <ivdoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This is an RT3572 based device.
Signed-off-by: Maximilian Engelhardt <maxi@daemonizer.de>
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Cc: <stable@vger.kernel.org>
Acked-by: Ivo Van Doorn <ivdoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The function brcmf_cfg80211_get_station requests the RSSI from
the device. The complete structure used needs to be cleared
before sending the request to firmware. Otherwise the request
fails filling the logs with "Could not get rssi (-2)" messages.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
On both rx and tx there is was a race condition on the queueing
of usb requests. When for example frame gets submitted it is
possible that complete function gets called even before
usb_submit_urb() returns. As a result it is possible that usb
requests get losts, which was noticed on OMAP4 pandaboard
platform. This patch fixes the race condition.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
URB_ZERO_PACKET should only be set or bulk OUT and this condition
is checked with a WARN_ON in usb_submit_urb(). This patch fixes
brcmfmac to get rid of this warning filling the logs.
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The USB part of the brcmfmac did a dev_kfree_skb() that resulted
in a warning in net/core/skbuff.c:
Jul 11 04:53:33 lb-bun-10 kernel: [53282.667745] WARNING: at
net/core/skbuff.c:490 skb_release_head_state+0xcc/0xe0()
The brcmutil modules provides brcmu_pkt_buf_free_skb() which takes
the context into account. This patch makes use of this function
instead of dev_kfree_skb().
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Generic timers for BTCOEX functionality is applicable
only for 3 WIRE BTCOEX (and MCI) chipsets.
Hence btcoex->no_stomp_timer is allocated only 3 WIRE
btcoex chipsets and in all the other cases its NULL.
Make sure we stop the generic timer only if
'btcoex->hw_timer_enabled' is true(only if its up and
running)
Fixes the following crash
[68757.020454] BUG: unable to handle kernel NULL pointer dereference at 0000000c
[68757.020916] IP: [<f9b055c3>] ath9k_hw_gen_timer_stop+0x13/0x80 [ath9k_hw]
[68757.021251] *pde = 00000000
[68757.024384] EIP: 0060:[<f9b055c3>] EFLAGS: 00010082 CPU: 0
[68757.024384] EIP is at ath9k_hw_gen_timer_stop+0x13/0x80 [ath9k_hw]
[68757.024384] EAX: d32d0000 EBX: d32d0000 ECX: 00000000 EDX: 00000000
[68757.024384] ESI: e67c24c0 EDI: 00000296 EBP: e137be2c ESP: e137be20
[68757.024384] DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
[68757.024384] CR0: 8005003b CR2: 0000000c CR3: 00b99000 CR4: 000407d0
[68757.024384] DR0: 00000000 DR1: 00000000 DR2: 00000000 DR3: 00000000
[68757.024384] DR6: ffff0ff0 DR7: 00000400
[68757.024384] Process kworker/u:2 (pid: 8917, ti=e137a000 task=ea7a6860 task.ti=e137a000)
[68757.024384] Stack:
[68757.024384] c06c4676 d32d0000 e67c24c0 e137be38 f81c9590 e67c1ca0 e137be40 f81c95d9
[68757.024384] e137be64 f81cd1c5 00000246 00000002 d32d0000 e67c05e0 e67c1ca0 e67c05e0
[68757.024384] 00000000 e137beac f81cdfa0 e137be84 00000246 00000246 e67c1ca0 e67c1ca0
[68757.024384] Call Trace:
[68757.024384] [<c06c4676>] ? _raw_spin_lock_irqsave+0x86/0xa0
[68757.024384] [<f81c9590>] ath9k_gen_timer_stop+0x10/0x40 [ath9k]
[68757.024384] [<f81c95d9>] ath9k_btcoex_stop_gen_timer+0x19/0x20 [ath9k]
[68757.024384] [<f81cd1c5>] ath9k_ps_restore+0x85/0x110 [ath9k]
[68757.024384] [<f81cdfa0>] ath9k_config+0x220/0x520 [ath9k]
[68757.024384] [<f81cd47d>] ? ath9k_flush+0x15d/0x1b0 [ath9k]
[68757.024384] [<f85c7ca5>] ieee80211_hw_config+0x135/0x2c0 [mac80211]
[68757.024384] [<f860e3c8>] ieee80211_dynamic_ps_enable_work+0x198/0x5f0 [mac80211]
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Cc: Bala Shanmugam <bkamatch@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This feature had been disabled in ath9k because the code to support
it was incomplete, but now the code is in sync with the internal QCA
codebase, so it's time to enable it.
On many newer devices, the calibration is assumed to be done with PA
linearization enabled.
Tests with a particular AR933x device showed that the signal emitted
at full power was highly distorted and unreliable with PA linearization
disabled. With this patch, the signal becomes clear and stability
is improved.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Before PAPRD training can run, the card needs to have sent a packet for
thermal calibration. Sending a dummy packet with the PAPRD training flag
set causes a crash under some circumstance.
Fix the code by replacing the dummy tx with a delay that waits for a
real packet tx to have occurred.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Support for it is incomplete
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Re-train if the calibrated PA linearization curve is out of bounds
(affects AR933x and AR9485).
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
That predistortion type is not supported
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The interrupt is no longer handling it. While it shouldn't fire (wraparound
is highly unlikely), the consequences would be fatal (interrupt storm).
Disable the interrupt to prevent that from happening.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
According to the vendor driver v2.6.0.1, during the rf register init the SRAM
voltage should be increased to 1.35V and after 1ms decreased back to 1.2V. This
patch adds the field setting of LDO_CFG0_LDO_CORE_VLEVEL accordingly.
Cc: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@blackshift.org>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
When we send a command to firmware, we assumed that cmd_size
will be always less than or equal to the structure size of
host_cmd_ds_command. However, this is no longer true after
we added AP support. There are some AP commands that Custom
IE TLVs are included in command buffer, hence the cmd_size
gets enlarged by the TLV data. We need to increase the skb
length for the extra data.
Signed-off-by: Stone Piao <piaoyun@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem
|
|
This change marks interface as down on reset, otherwise the driver can't
reinitialize itself properly.
Without the change a transient problem turns out to be critical and leads
to inavailability to reset the driver without brcmsmac module unload/load
cycle:
ieee80211 phy0: wl0: PSM microcode watchdog fired at 5993 (seconds). Resetting.
brcms_c_dpc : PSM Watchdog, chipid 0xa8d9, chiprev 0x1
ieee80211 phy0: wl0: fatal error, reinitializing
ieee80211 phy0: Hardware restart was requested
ieee80211 phy0: brcms_ops_start: brcms_up() returned -19
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Cc: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Pull networking update from David Miller:
"A couple weeks of bug fixing in there. The largest chunk is all the
broken crap Amerigo Wang found in the netpoll layer."
1) netpoll and it's users has several serious bugs:
a) uses GFP_KERNEL with locks held
b) interfaces requiring interrupts disabled are called with them
enabled
c) and vice versa
d) VLAN tag demuxing, as per all other RX packet input paths, is not
applied
All from Amerigo Wang.
2) Hopefully cure the ipv4 mapped ipv6 address TCP early demux bugs for
good, from Neal Cardwell.
3) Unlike AF_UNIX, AF_PACKET sockets don't set a default credentials
when the user doesn't specify one explicitly during sendmsg().
Instead we attach an empty (zero) SCM credential block which is
definitely not what we want. Fix from Eric Dumazet.
4) IPv6 illegally invokes netdevice notifiers with RCU lock held, fix
from Ben Hutchings.
5) inet_csk_route_child_sock() checks wrong inet options pointer, fix
from Christoph Paasch.
6) When AF_PACKET is used for transmit, packet loopback doesn't behave
properly when a socket fanout is enabled, from Eric Leblond.
7) On bluetooth l2cap channel create failure, we leak the socket, from
Jaganath Kanakkassery.
8) Fix all the netprio file handling bugs found by Al Viro, from John
Fastabend.
9) Several error return and NULL deref bug fixes in networking drivers
from Julia Lawall.
10) A large smattering of struct padding et al. kernel memory leaks to
userspace found of Mathias Krause.
11) Conntrack expections in netfilter can access an uninitialized timer,
fix from Pablo Neira Ayuso.
12) Several netfilter SIP tracker bug fixes from Patrick McHardy.
13) IPSEC ipv6 routes are not initialized correctly all the time,
resulting in an OOPS in inet_putpeer(). Also from Patrick McHardy.
14) Bridging does rcu_dereference() outside of RCU protected area, from
Stephen Hemminger.
15) Fix routing cache removal performance regression when looking up
output routes that have a local destination. From Zheng Yan.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (87 commits)
af_netlink: force credentials passing [CVE-2012-3520]
ipv4: fix ip header ident selection in __ip_make_skb()
ipv4: Use newinet->inet_opt in inet_csk_route_child_sock()
tcp: fix possible socket refcount problem
net: tcp: move sk_rx_dst_set call after tcp_create_openreq_child()
net/core/dev.c: fix kernel-doc warning
netconsole: remove a redundant netconsole_target_put()
net: ipv6: fix oops in inet_putpeer()
net/stmmac: fix issue of clk_get for Loongson1B.
caif: Do not dereference NULL in chnl_recv_cb()
af_packet: don't emit packet on orig fanout group
drivers/net/irda: fix error return code
drivers/net/wan/dscc4.c: fix error return code
drivers/net/wimax/i2400m/fw.c: fix error return code
smsc75xx: add missing entry to MAINTAINERS
net: qmi_wwan: new devices: UML290 and K5006-Z
net: sh_eth: Add eth support for R8A7779 device
netdev/phy: skip disabled mdio-mux nodes
dt: introduce for_each_available_child_of_node, of_get_next_available_child
net: netprio: fix cgrp create and write priomap race
...
|
|
If the device is not started, we can't read its
SRAM and attempting to do so will cause issues.
Protect the debugfs read.
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
iwl_dbgfs_fh_reg_read() can cause crashes and/or
BUG_ON in slub because the ifdefs are wrong, the
code in iwl_dump_fh() should use DEBUGFS, not
DEBUG to protect the buffer writing code.
Also, while at it, clean up the arguments to the
function, some code and make it generally safer.
Cc: stable@vger.kernel.org
Reported-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The result of one call to a function is tested, and then at the second call
to the same function, the previous result, and not the current result, is
tested again.
Also changed &bssid to bssid, at the suggestion of Stanislav Yakovlev.
The semantic match that finds the first problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression ret;
identifier f;
statement S1,S2;
@@
*ret = f(...);
if (\(ret != 0\|ret < 0\|ret == NULL\)) S1
... when any
*f(...);
if (\(ret != 0\|ret < 0\|ret == NULL\)) S2
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch reduces the per rate target power eeprom reads for
AR5K_EEPROM_MODE_11A from 10 to 8, as there are only 8 valid
power curve entries on the eeprom. The former 10 reads lead to
equal max power limits per rate and this causes an increasing
distortion for all rates above 24 MBit and leads to a needless
poor performance in 802.11a mode.
Signed-off-by: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull more USB patches from Greg Kroah-Hartman:
"Here are 10 more USB patches for 3.6-rc3. They all fix reported
problems (build problems for one of them, and easily repeatable oopses
for the others.)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'usb-3.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
gpu/mfd/usb: Fix USB randconfig problems
USB: CDC ACM: Fix NULL pointer dereference
USB: emi62: remove __devinit* from the struct usb_device_id table
USB: winbond: remove __devinit* from the struct usb_device_id table
USB: vt6656: remove __devinit* from the struct usb_device_id table
USB: rtl8187: remove __devinit* from the struct usb_device_id table
USB: p54usb: remove __devinit* from the struct usb_device_id table
USB: spca506: remove __devinit* from the struct usb_device_id table
USB: jl2005bcd: remove __devinit* from the struct usb_device_id table
USB: smsusb: remove __devinit* from the struct usb_device_id table
|
|
This structure needs to always stick around, even if CONFIG_HOTPLUG
is disabled, otherwise we can oops when trying to probe a device that
was added after the structure is thrown away.
Thanks to Fengguang Wu and Bjørn Mork for tracking this issue down.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Reported-by: Bjørn Mork <bjorn@mork.no>
Cc: stable <stable@vger.kernel.org>
CC: Herton Ronaldo Krzesinski <herton@canonical.com>
CC: Hin-Tak Leung <htl10@users.sourceforge.net>
CC: Larry Finger <Larry.Finger@lwfinger.net>
CC: "John W. Linville" <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This structure needs to always stick around, even if CONFIG_HOTPLUG
is disabled, otherwise we can oops when trying to probe a device that
was added after the structure is thrown away.
Thanks to Fengguang Wu and Bjørn Mork for tracking this issue down.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Reported-by: Bjørn Mork <bjorn@mork.no>
Cc: stable <stable@vger.kernel.org>
CC: Christian Lamparter <chunkeey@googlemail.com>
CC: "John W. Linville" <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem
|
|
Lockdep found an inconsistent lock state when joining a mesh with
ath5k. The problem is that ath5k takes the lock for its beacon state,
ah->block, with spin_lock_irqsave(), while mesh internally takes the
sync_offset_lock with spin_lock_bh() in mesh_sync_offset_adjust_tbtt(),
which in turn is called under ah->block.
This could deadlock if the beacon tasklet was run on the processor
that held the beacon lock during the do_softirq() in spin_unlock_bh().
We probably shouldn't hold the lock around the callbacks, but the
easiest fix is to switch to spin_lock_bh for ah->block: it doesn't
need interrupts disabled anyway as the data in question is only accessed
in softirq or process context.
Fixes the following lockdep warning:
[ 446.892304] WARNING: at kernel/softirq.c:159 _local_bh_enable_ip+0x38/0xa6()
[ 446.892306] Hardware name: MacBook1,1
[ 446.892309] Modules linked in: tcp_lp fuse sunrpc cpufreq_ondemand acpi_cpufreq mperf ip6t_REJECT nf_conntrack_ipv6 nf_defrag_ipv6 nf_conntrack_ipv4 ip6table_filter nf_defrag_ipv4 xt_state nf_conntrack ip6_tables ext2 arc4 btusb bluetooth snd_hda_codec_idt snd_hda_intel carl9170 snd_hda_codec coretemp joydev ath5k snd_hwdep snd_seq isight_firmware ath snd_seq_device snd_pcm applesmc appletouch mac80211 input_polldev snd_timer microcode cfg80211 snd lpc_ich pcspkr i2c_i801 mfd_core soundcore rfkill snd_page_alloc sky2 tpm_infineon virtio_net kvm_intel kvm i915 drm_kms_helper drm i2c_algo_bit i2c_core video
[ 446.892385] Pid: 1892, comm: iw Not tainted 3.6.0-rc1-wl+ #296
[ 446.892387] Call Trace:
[ 446.892394] [<c0432958>] warn_slowpath_common+0x7c/0x91
[ 446.892398] [<c04399d7>] ? _local_bh_enable_ip+0x38/0xa6
[ 446.892403] [<c04399d7>] ? _local_bh_enable_ip+0x38/0xa6
[ 446.892459] [<f7f9ae3b>] ? mesh_sync_offset_adjust_tbtt+0x95/0x99 [mac80211]
[ 446.892464] [<c043298f>] warn_slowpath_null+0x22/0x24
[ 446.892468] [<c04399d7>] _local_bh_enable_ip+0x38/0xa6
[ 446.892473] [<c0439a52>] local_bh_enable_ip+0xd/0xf
[ 446.892479] [<c088004f>] _raw_spin_unlock_bh+0x34/0x37
[ 446.892527] [<f7f9ae3b>] mesh_sync_offset_adjust_tbtt+0x95/0x99 [mac80211]
[ 446.892569] [<f7f7650f>] ieee80211_beacon_get_tim+0x28f/0x4e0 [mac80211]
[ 446.892575] [<c047ceeb>] ? trace_hardirqs_on_caller+0x10e/0x13f
[ 446.892591] [<f7fdc541>] ath5k_beacon_update+0x40/0x26b [ath5k]
[ 446.892597] [<c047ad67>] ? lock_acquired+0x1f5/0x21e
[ 446.892612] [<f7fdf9fb>] ? ath5k_bss_info_changed+0x167/0x1b2 [ath5k]
[ 446.892617] [<c087f9ea>] ? _raw_spin_lock_irqsave+0x78/0x82
[ 446.892632] [<f7fdf9fb>] ? ath5k_bss_info_changed+0x167/0x1b2 [ath5k]
[ 446.892647] [<f7fdfa09>] ath5k_bss_info_changed+0x175/0x1b2 [ath5k]
[ 446.892651] [<c0479dd4>] ? lock_is_held+0x73/0x7b
[ 446.892662] [<c0458fd5>] ? __might_sleep+0xa7/0x17a
[ 446.892698] [<f7f5d8f7>] ieee80211_bss_info_change_notify+0x1ed/0x21a [mac80211]
[ 446.892703] [<c0449875>] ? queue_work+0x24/0x32
[ 446.892718] [<f7fdf894>] ? ath5k_configure_filter+0x163/0x163 [ath5k]
[ 446.892766] [<f7f95fa4>] ieee80211_start_mesh+0xb9/0xbd [mac80211]
[ 446.892806] [<f7f6e610>] ieee80211_join_mesh+0x10c/0x116 [mac80211]
[ 446.892834] [<f7a96b90>] __cfg80211_join_mesh+0x176/0x1b3 [cfg80211]
[ 446.892855] [<f7a96c1c>] cfg80211_join_mesh+0x4f/0x6a [cfg80211]
[ 446.892875] [<f7a89891>] nl80211_join_mesh+0x1de/0x1ed [cfg80211]
[ 446.892908] [<f7a8db99>] ? nl80211_set_wiphy+0x4cf/0x4cf [cfg80211]
[ 446.892919] [<c07cfa36>] genl_rcv_msg+0x1d5/0x1f3
[ 446.892940] [<c07cf861>] ? genl_rcv+0x25/0x25
[ 446.892946] [<c07cf009>] netlink_rcv_skb+0x37/0x78
[ 446.892950] [<c07cf85a>] genl_rcv+0x1e/0x25
[ 446.892955] [<c07cebf3>] netlink_unicast+0xc3/0x12d
[ 446.892959] [<c07cee46>] netlink_sendmsg+0x1e9/0x213
[ 446.892966] [<c079f282>] sock_sendmsg+0x79/0x96
[ 446.892972] [<c04eb90d>] ? might_fault+0x9d/0xa3
[ 446.892978] [<c07a81d8>] ? copy_from_user+0x8/0xa
[ 446.892983] [<c07a852c>] ? verify_iovec+0x43/0x77
[ 446.892987] [<c079f4d8>] __sys_sendmsg+0x180/0x215
[ 446.892993] [<c045f107>] ? sched_clock_cpu+0x134/0x144
[ 446.892997] [<c047992f>] ? trace_hardirqs_off+0xb/0xd
[ 446.893002] [<c047bf88>] ? __lock_acquire+0x46b/0xb6e
[ 446.893006] [<c047992f>] ? trace_hardirqs_off+0xb/0xd
[ 446.893010] [<c045f149>] ? local_clock+0x32/0x49
[ 446.893015] [<c0479ec1>] ? lock_release_holdtime.part.9+0x4b/0x51
[ 446.893020] [<c0479dd4>] ? lock_is_held+0x73/0x7b
[ 446.893025] [<c050d127>] ? fcheck_files+0x97/0xcd
[ 446.893029] [<c050d4df>] ? fget_light+0x2d/0x81
[ 446.893034] [<c07a01f3>] sys_sendmsg+0x3b/0x52
[ 446.893038] [<c07a07b4>] sys_socketcall+0x238/0x2a2
[ 446.893044] [<c0885edf>] sysenter_do_call+0x12/0x38
[ 446.893047] ---[ end trace a9af5998f929270f ]---
[ 447.627222]
[ 447.627232] =================================
[ 447.627237] [ INFO: inconsistent lock state ]
[ 447.627244] 3.6.0-rc1-wl+ #296 Tainted: G W
[ 447.627248] ---------------------------------
[ 447.627253] inconsistent {SOFTIRQ-ON-W} -> {IN-SOFTIRQ-W} usage.
[ 447.627260] swapper/0/0 [HC0[0]:SC1[1]:HE1:SE0] takes:
[ 447.627264] (&(&ah->block)->rlock){+.?...}, at: [<f7fdd2d1>] ath5k_tasklet_beacon+0x91/0xa7 [ath5k]
[ 447.627299] {SOFTIRQ-ON-W} state was registered at:
[ 447.627304] [<c047cdbf>] mark_held_locks+0x59/0x77
[ 447.627316] [<c047ceeb>] trace_hardirqs_on_caller+0x10e/0x13f
[ 447.627324] [<c047cf27>] trace_hardirqs_on+0xb/0xd
[ 447.627332] [<c0439a3d>] _local_bh_enable_ip+0x9e/0xa6
[ 447.627342] [<c0439a52>] local_bh_enable_ip+0xd/0xf
[ 447.627349] [<c088004f>] _raw_spin_unlock_bh+0x34/0x37
[ 447.627359] [<f7f9ae3b>] mesh_sync_offset_adjust_tbtt+0x95/0x99 [mac80211]
[ 447.627451] [<f7f7650f>] ieee80211_beacon_get_tim+0x28f/0x4e0 [mac80211]
[ 447.627526] [<f7fdc541>] ath5k_beacon_update+0x40/0x26b [ath5k]
[ 447.627547] [<f7fdfa09>] ath5k_bss_info_changed+0x175/0x1b2 [ath5k]
[ 447.627569] [<f7f5d8f7>] ieee80211_bss_info_change_notify+0x1ed/0x21a [mac80211]
[ 447.627628] [<f7f95fa4>] ieee80211_start_mesh+0xb9/0xbd [mac80211]
[ 447.627712] [<f7f6e610>] ieee80211_join_mesh+0x10c/0x116 [mac80211]
[ 447.627782] [<f7a96b90>] __cfg80211_join_mesh+0x176/0x1b3 [cfg80211]
[ 447.627816] [<f7a96c1c>] cfg80211_join_mesh+0x4f/0x6a [cfg80211]
[ 447.627845] [<f7a89891>] nl80211_join_mesh+0x1de/0x1ed [cfg80211]
[ 447.627872] [<c07cfa36>] genl_rcv_msg+0x1d5/0x1f3
[ 447.627881] [<c07cf009>] netlink_rcv_skb+0x37/0x78
[ 447.627891] [<c07cf85a>] genl_rcv+0x1e/0x25
[ 447.627898] [<c07cebf3>] netlink_unicast+0xc3/0x12d
[ 447.627907] [<c07cee46>] netlink_sendmsg+0x1e9/0x213
[ 447.627915] [<c079f282>] sock_sendmsg+0x79/0x96
[ 447.627926] [<c079f4d8>] __sys_sendmsg+0x180/0x215
[ 447.627934] [<c07a01f3>] sys_sendmsg+0x3b/0x52
[ 447.627941] [<c07a07b4>] sys_socketcall+0x238/0x2a2
[ 447.627949] [<c0885edf>] sysenter_do_call+0x12/0x38
[ 447.627959] irq event stamp: 1929200
[ 447.627963] hardirqs last enabled at (1929200): [<c043a0e9>] tasklet_hi_action+0x3e/0xbf
[ 447.627972] hardirqs last disabled at (1929199): [<c043a0c0>] tasklet_hi_action+0x15/0xbf
[ 447.627981] softirqs last enabled at (1929196): [<c043999d>] _local_bh_enable+0x12/0x14
[ 447.627989] softirqs last disabled at (1929197): [<c040443b>] do_softirq+0x63/0xb8
[ 447.627999]
[ 447.627999] other info that might help us debug this:
[ 447.628004] Possible unsafe locking scenario:
[ 447.628004]
[ 447.628009] CPU0
[ 447.628012] ----
[ 447.628016] lock(&(&ah->block)->rlock);
[ 447.628023] <Interrupt>
[ 447.628027] lock(&(&ah->block)->rlock);
[ 447.628034]
[ 447.628034] *** DEADLOCK ***
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
ath_rx_tasklet() calls ath9k_rx_skb_preprocess() and ath9k_rx_skb_postprocess()
in a loop over the received frames. The decrypt_error flag is
initialized to false
just outside ath_rx_tasklet() loop. ath9k_rx_accept(), called by
ath9k_rx_skb_preprocess(),
only sets decrypt_error to true and never to false.
Then ath_rx_tasklet() calls ath9k_rx_skb_postprocess() and passes
decrypt_error to it.
So, after a decryption error, in ath9k_rx_skb_postprocess(), we can
have a leftover value
from another processed frame. In that case, the frame will not be marked with
RX_FLAG_DECRYPTED even if it is decrypted correctly.
When using CCMP encryption this issue can lead to connection stuck
because of CCMP
PN corruption and a waste of CPU time since mac80211 tries to decrypt an already
deciphered frame with ieee80211_aes_ccm_decrypt.
Fix the issue initializing decrypt_error flag at the begging of the
ath_rx_tasklet() loop.
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Cc: <stable@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
During suspend, the device will be moved to FULLSLEEP state.
As btcoex is never been stopped, the btcoex timer is running
and tries to access hw on fullsleep state. Fix that.
Cc: stable@vger.kernel.org
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This return holds the number of bytes transfered (1 byte) or a negative
error code. The type should be int instead of u8.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Do not leak memory by updating pointer with potentially NULL realloc return value.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
commit b74713d04effbacd3d126ce94cec18742187b6ce
"ath9k: Handle fatal interrupts properly" introduced a race condition, where
IRQs are being left enabled, however the irq handler returns IRQ_HANDLED
while the reset is still queued without addressing the IRQ cause.
This leads to an IRQ storm that prevents the system from even getting to
the reset code.
Fix this by disabling IRQs in the handler without touching intr_ref_cnt.
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Cc: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem
|
|
Pull networking fixes from David Miller:
1) Missed rcu_assign_pointer() in mac80211 scanning, from Johannes
Berg.
2) Allow devices to limit the number of segments that an individual
TCP TSO packet can use at a time, to deal with device and/or driver
specific limitations. From Ben Hutchings.
3) Fix unexpected hard IPSEC expiration after setting the date. From
Fan Du.
4) Memory leak fix in bxn2x driver, from Jesper Juhl.
5) Fix two memory leaks in libertas driver, from Daniel Drake.
6) Fix deref of out-of-range array index in packet scheduler generic
actions layer. From Hiroaki SHIMODA.
7) Fix TX flow control errors in mlx4 driver, from Yevgeny Petrilin.
8) Fix CRIS eth_v10.c driver build, from Randy Dunlap.
9) Fix wrong SKB freeing in LLC protocol layer, from Sorin Dumitru.
10) The IP output path checks neigh lookup errors incorrectly, it needs
to use IS_ERR(). From Vasiliy Kulikov.
11) An estimator leak leads to deref of freed memory in timer handler,
fix from Hiroaki SHIMODA.
12) TCP early demux in ipv6 needs to use DST cookies in order to
validate the RX route properly. Fix from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (43 commits)
net: ipv6: fix TCP early demux
net: Use PTR_RET rather than if(IS_ERR(.. [1]
net_sched: act: Delete estimator in error path.
ip: fix error handling in ip_finish_output2()
llc: free the right skb
ixp4xx_eth: fix ptp_ixp46x build failure
drivers/atm/iphase.c: fix error return code
tcp_output: fix sparse warning for tcp_wfree
drivers/net/phy/mdio-mux-gpio.c: drop devm_kfree of devm_kzalloc'd data
batman-adv: select an internet gateway if none was chosen
mISDN: Bugfix for layer2 fixed TEI mode
igb: don't break user visible strings over multiple lines in igb_ethtool.c
igb: correct hardware type (i210/i211) check in igb_loopback_test()
igb: Fix for failure to init on some 82576 devices.
cris: fix eth_v10.c build error
cdc-ncm: tag Ericsson WWAN devices (eg F5521gw) with FLAG_WWAN
isdnloop: fix and simplify isdnloop_init()
hyperv: Move wait completion msg code into rndis_filter_halt_device()
net/mlx4_core: Remove port type restrictions
net/mlx4_en: Fixing TX queue stop/wake flow
...
|
|
There's a bug that causes the rate scaling to get stuck
when it has to use single-stream rates with a peer that
can do GF and SGI; the two are incompatible so we can't
use them together, but that causes the algorithm to not
work at all, it always rejects updates.
Disable greenfield for now to prevent that problem.
Cc: stable@vger.kernel.org
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Tested-by: Cesar Eduardo Barros <cesarb@cesarb.net>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
We can not pass NULL libconf->conf->channel to rt61pci_config() as it
is dereferenced unconditionally in rt61pci_config_lna_gain() subroutine.
Resolves:
https://bugzilla.kernel.org/show_bug.cgi?id=44361
Cc: stable@vger.kernel.org
Reported-and-tested-by: <dolohow@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
AR1111 is same as AR9485. The h/w
difference between them is quite insignificant,
Felix suggests only very few baseband features
may not be available in AR1111. The h/w code for
AR9485 is already present, so AR1111 should
work fine with the addition of its PID/VID.
Cc: stable@vger.kernel.org [2.6.39+]
Cc: Felix Bitterli <felixb@qca.qualcomm.com>
Reported-by: Tim Bentley <Tim.Bentley@Gmail.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Tested-by: Tim Bentley <Tim.Bentley@Gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Pull OLPC platform updates from Andres Salomon:
"These move the OLPC Embedded Controller driver out of
arch/x86/platform and into drivers/platform/olpc.
OLPC machines are now ARM-based (which means lots of x86 and ARM
changes), but are typically pretty self-contained.. so it makes more
sense to go through a separate OLPC tree after getting the appropriate
review/ACKs."
* 'for-linus-3.6' of git://dev.laptop.org/users/dilinger/linux-olpc:
x86: OLPC: move s/r-related EC cmds to EC driver
Platform: OLPC: move global variables into priv struct
Platform: OLPC: move debugfs support from x86 EC driver
x86: OLPC: switch over to using new EC driver on x86
Platform: OLPC: add a suspended flag to the EC driver
Platform: OLPC: turn EC driver into a platform_driver
Platform: OLPC: allow EC cmd to be overridden, and create a workqueue to call it
drivers: OLPC: update various drivers to include olpc-ec.h
Platform: OLPC: add a stub to drivers/platform/ for the OLPC EC driver
|
|
brcmsmac cannot call freq_reg_info() during channel changes as it does
not hold cfg80211_lock, and as a result it generates a lockdep warning.
freq_reg_info() is being used to determine whether OFDM is allowed on
the current channel, so we can avoid the errant call by using the new
IEEE80211_CHAN_NO_OFDM for this purpose instead.
Reported-by: Josh Boyer <jwboyer@redhat.com>
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
John W. Linville
Hante Meuleman
Larry Finger
Colin Ian King
Felix Fietkau
Arend van Spriel
Daniel Drake
Sergei Poselenov
Gertjan van Wingerde
Mohammed Shafi Shajakhan
Marc Kleine-Budde
Stone Piao
Vladimir Zapolskiy
Linus Torvalds
Johannes Berg
Julia Lawall
Thomas Huehn
Greg Kroah-Hartman
Bob Copeland
Lorenzo Bianconi
Rajkumar Manoharan
Dan Carpenter
Alexey Khoroshilov
Stanislaw Gruszka
Seth Forshee