| Age | Commit message (Collapse) | Author |
|---|
|
It is possible to turn off the card clock by setting
the frequency to zero via debugfs e.g.
echo 0 > /sys/kernel/debug/mmc0/clock
However that produces an incorrect warning that is
designed to warn if the frequency is below the minimum
operating frequency. So correct the warning.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Add MMC_POWER_UNDEFINED for power_mode in struct mmc_ios and use it as
the initial value of host->ios.power_mode.
For hosts with MMC_CAP2_NO_PRESCAN_POWERUP, this makes the later
mmc_power_off() do real power-off things instead of NOP, and further
prevents state messed up in cards that was already initialized (eg. by
BIOS of UEFI driver).
Signed-off-by: Roger Tseng <rogerable@realtek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Use the much more common pr_warn instead of pr_warning.
Other miscellanea:
o Coalesce formats
o Realign arguments
o Remove extra spaces when coalescing formats
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
With one special SD card, below divide by zero error observed:
...
[ 2.144300] divide error: 0000 [#1] PREEMPT SMP
[ 2.148860] Modules linked in:
[ 2.151898]
[ 2.152685] Set up 4031 stolen pages starting at 0x0001f000, GTT offset 0K
[ 2.157330] Set up 0 CI stolen pages starting at 0x00000000, GTT offset 131072K
[ 2.167581] Pid: 5, comm: kworker/u:0 Not tainted 3.0.8-138216-g974a2ab #1
[ 2.169506] [drm] PSB GTT mem manager ready, tt_start 4031, tt_size 28737 pages
[ 2.169906] [drm] SGX core id = 0x00000000
[ 2.169920] [drm] SGX core rev major = 0x00, minor = 0x00
[ 2.169934] [drm] SGX core rev maintenance = 0x00, designer = 0x00
[ 2.197370] Intel Corporation Medfield/iCDKB
[ 2.201716] EIP: 0060:[<c1697ca6>] EFLAGS: 00010246 CPU: 1
[ 2.207198] EIP is at mmc_init_erase+0x76/0x150
[ 2.211704] EAX: 00002000 EBX: dcd1b400 ECX: 00002000 EDX: 00000000
[ 2.217957] ESI: 00000000 EDI: dcd5c800 EBP: dd867e84 ESP: dd867e7c
[ 2.224214] DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0068
[ 2.229605] Process kworker/u:0 (pid: 5, ti=dd866000 task=dd868000 task.ti=dd866000)
[ 2.237325] Stack:
[ 2.239322] dcd1b400 00000000 dd867eb0 c16a06da c1ab7c44 dd995aa8 00000003 00000000
[ 2.247054] 00000000 00000000 dcd5c800 00000000 dcd1b400 dd867ef8 c16a1012 c1698b00
[ 2.254785] 00000029 00000001 c194eb80 dcd5c9ec dd867e00 c1239b00 00000000 00000000
[ 2.262519] Call Trace:
[ 2.264975] [<c16a06da>] mmc_sd_setup_card+0x1da/0x4f0
[ 2.270183] [<c16a1012>] mmc_sd_init_card+0x192/0xc40
[ 2.275304] [<c1698b00>] ? __mmc_claim_host+0x160/0x160
[ 2.280610] [<c1239b00>] ? __schedule_bug+0x50/0x80
[ 2.285556] [<c16a1b89>] mmc_attach_sd+0xc9/0x230
[ 2.290333] [<c169b6ef>] mmc_rescan+0x25f/0x2c0
[ 2.294943] [<c1274223>] process_one_work+0x103/0x400
[ 2.300065] [<c12670fd>] ? mod_timer+0x1ad/0x3c0
[ 2.304756] [<c169b490>] ? mmc_suspend_host+0x1a0/0x1a0
[ 2.310056] [<c127502d>] worker_thread+0x12d/0x4a0
[ 2.314921] [<c18fcfbd>] ? preempt_schedule+0x2d/0x50
[ 2.320047] [<c1274f00[ 2.323976] ---[ end trace 5398ec2720494438 ]---
...
So, seems this bad SD card does not set valid value in related SSR / CSD register fields.
And then the driver will set card->erase_size to 0.
Then it triggered this divided by zero error when calculate card->pref_erase.
Submit this patch to fix the issue.
Signed-off-by: Yunpeng Gao <yunpeng.gao@intel.com>
Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The operation conditions register (OCR) stores the voltage
profile of the card, however the list of possible voltages
is restricted by the voltage range supported by the supply
used as VCC/VDD. So in mmc_vddrange_to_ocrmask() a OCR mask
is obtained to filter the not supported voltages, from the
value read in the host controller OCR register.
For fixed regulators, regulator_list_voltage() returns the
fixed output for the first selector but this doesn't happen
for switch (FET) regulators that obtain their voltage from
their parent supply. A call to regulator_get_voltage() is
needed in this case so the regulator core can return the
FET's parent supply voltage output.
This change is consistent with the fact that for other
fixed regulators (that are not FETs) the OCR mask is
returned even when mmc_regulator_set_ocr() checks if the
regulator is fixed before calling regulator_set_voltage().
Without this patch, the following warning is reported when
a FET is used as a vmmc-supply:
dwmmc_exynos 12220000.mmc: Failed getting OCR mask: -22
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
There is no need for regulator consumers to include special logic for
fixed voltage regulators as they support regulator_set_voltage() just
like their non-fixed regulator counterparts.
Signed-off-by: Tim Kryger <tim.kryger@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Currently when the device secure discard implementation is
blacklisted (MMC_QUIRK_SEC_ERASE_TRIM_BROKEN quirk is set)
instead of secure discard we're going to do normal discard,
which is wrong.
When the secure discard is known to be broken we should just
disallow it entirely and not advertise this functionality to
the user. Fix it.
Also move mmc_fixup_device() in from of mmc_blk_alloc() so we
can get quirks set before we attempt to set queue information.
Signed-off-by: Lukas Czerner <lczerner@redhat.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Callers of mmc_regulator_get_supply could benefit from knowing if either
of the regulators are present but not yet available. Since callers do
not currently examine the return value, modify this function to return
zero or -EPROBE_DEFER if either regulator get returns the same.
Furthermore, since callers check vmmc/vqmmc using IS_ERR and can deal
with absent regulators, switch to devm_regulator_get_optional. This has
the added benefit of allowing this function to behave correctly even in
the !CONFIG_REGULATOR case such that the stub can be removed.
Signed-off-by: Tim Kryger <tim.kryger@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
|
|
Timing mode identifier has same role and can take the place
of speed mode. This change removes all related speed mode.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
|
|
The eMMC signalling voltage is determined by VCCQ which is provided to
the card by the host. Signalling is not required to begin at 3.3v and,
if the host and card both support a particular VCC/VCCQ combination, it
can be used immediately.
In contrast, SD Cards must begin with 3.3v signalling and may switch to
a lower voltage signalling if instructed to do so in CMD11. A message
is required to coordinate this operation because the card only receives
a 3.3v VDD and must know when to use the 1.8v produced by its internal
regulator.
It makes sense for the core to begin with 3.3v signalling but when that
can't be set, 1.8v and 1.2v signalling also should be attempted. This
is especially important when an external regulator with a limited range
is used to supply VCCQ to an eMMC part.
Signed-off-by: Tim Kryger <tim.kryger@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
|
|
When plugging a specific micro SD card at MMC socket of a custom i.MX28 board,
we get the following kernel warning:
WARNING: CPU: 0 PID: 30 at drivers/mmc/host/mxs-mmc.c:342 mxs_mmc_start_cmd+0x34c/0x378()
Modules linked in:
CPU: 0 PID: 30 Comm: kworker/u2:1 Not tainted 3.14.0-rc5 #8
Workqueue: kmmcd mmc_rescan
[<c0015420>] (unwind_backtrace) from [<c0012cb0>] (show_stack+0x10/0x14)
[<c0012cb0>] (show_stack) from [<c001daf8>] (warn_slowpath_common+0x6c/0x8c)
[<c001daf8>] (warn_slowpath_common) from [<c001db34>] (warn_slowpath_null+0x1c/0x24)
[<c001db34>] (warn_slowpath_null) from [<c0349478>] (mxs_mmc_start_cmd+0x34c/0x378)
[<c0349478>] (mxs_mmc_start_cmd) from [<c0338fa0>] (mmc_start_request+0xc4/0xf4)
[<c0338fa0>] (mmc_start_request) from [<c03390b4>] (mmc_wait_for_req+0x50/0x164)
[<c03390b4>] (mmc_wait_for_req) from [<c03405b8>] (mmc_app_send_scr+0x158/0x1c8)
[<c03405b8>] (mmc_app_send_scr) from [<c033ee1c>] (mmc_sd_setup_card+0x80/0x3c8)
[<c033ee1c>] (mmc_sd_setup_card) from [<c033f788>] (mmc_sd_init_card+0x124/0x66c)
[<c033f788>] (mmc_sd_init_card) from [<c033fd7c>] (mmc_attach_sd+0xac/0x174)
[<c033fd7c>] (mmc_attach_sd) from [<c033a658>] (mmc_rescan+0x25c/0x2d8)
[<c033a658>] (mmc_rescan) from [<c003597c>] (process_one_work+0x1b4/0x4ec)
[<c003597c>] (process_one_work) from [<c0035de4>] (worker_thread+0x130/0x464)
[<c0035de4>] (worker_thread) from [<c003c824>] (kthread+0xb4/0xd0)
[<c003c824>] (kthread) from [<c000f420>] (ret_from_fork+0x14/0x34)
The error is due to an invalid value in CSD register of a specific 2GB
micro SD card. The CSD version of this card is 1.0 but the TACC field
has the invalid value 0.
cid:0000005553442020000000000000583f
csd:00000032535a83bfedb7ffbf1680003f
date:08/2005
erase_size:512
fwrev:0x0
hwrev:0x0
manfid:0x000000
name:USD
oemid:0x0000
preferred_erase_size:4194304
scr:0225000000000000
serial:0x00000000
type:SD
Since the kernel is making use of this TACC field to calculate the SD
card timeout, an invalid value 0 leads to a warning at
mxs_ns_to_ssp_ticks() and later the following misleading error message
appears in a loop:
mxs-mmc 80010000.ssp: card claims to support voltages below defined range
mxs-mmc 80010000.ssp: no support for card's volts
mmc0: error -22 whilst initialising MMC card
This error is only found on this 2GB SD card on mxs platform.
On x86 this card works without any problems.
The following patch based on the work of Peter Chan and Otavio Salvador.
It catches the case that the determined timeout is still 0 and sets it
to a valid value.
Successful tested on a i.MX28 board.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
|
|
This change removes the callback from atomic context which it doesn't
need to be in, and puts it in line with the debounced rescan.
This code is based on these e-mail threads with Christian Daudt:
https://lkml.org/lkml/2013/8/19/539
https://lkml.org/lkml/2014/3/19/79
Signed-off-by: Markus Mayer <markus.mayer@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
|
|
Add functions to request a CD GPIO using the GPIO descriptor API.
Note that the new request function is paired with mmc_gpiod_free_cd()
not mmc_gpio_free_cd(). Note also that it must be called prior to
mmc_add_host() otherwise the caller must also call
mmc_gpiod_request_cd_irq().
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
|
|
Instead of handle specific adaptations, releated to certain switch
operations, inside __mmc_switch, push this to be handled by the caller
instead.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
|
|
To better reflect that the cmd_timeout_ms is directly related to the
busy detection timeout, let's rename it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
|
|
Rename host->max_discard_to to host->max_busy_timeout, to reflect that
it tells the mmc core layer about the maximum supported busy detection
timeout by the host.
This timeout is at the moment only applicable to erase/trim/discard
commands. By the renaming we provide the option of make use of it for
other commands that cares about busy detection. In other words, those
commands that wants an R1B response, like for example the mmc switch
command.
Do note that the max_busy_timeout is supposed to be specified only by
hosts supporting MMC_CAP_WAIT_WHILE_BUSY.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
|
|
There are no reason to why the use of a non-volatile internal eMMC
cache should be controlled by a host cap. Instead let's just enable it
if the eMMC card supports it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <chris@printf.net>
|
|
Earlier we disabled the cache during suspend, which meant a flush was
internally at the eMMC performed as well.
To simplify code we can make use of the mmc_flush_cache(), during mmc
suspend, which makes the mmc_cache_ctrl() redundant so then we can
remove it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <chris@printf.net>
|
|
Due to the removal of the Kconfig option MMC_UNSAFE_RESUME, several
validations of a present bus_ops callback became redundant. Let's
remove these.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
|
|
Invoking system suspend or shutdown without using the Kconfig option
MMC_UNSAFE_RESUME, did trigger an ungraceful power cut of the card.
To improve the situation, change the behavior to always make use of the
available bus_ops callbacks that handles system suspend and shutdown
properly.
By changing the behavior MMC_UNSAFE_RESUME becomes redundant, so lets's
remove it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
|
|
Non removable cards are always present, so do not call get_cd for them.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
The are no more users of the deprecated mmc_suspend|resume_host API,
so let's remove it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
We want to give user space provision to fully consume a card
insert/remove event, when the event was caused by a wakeup irq.
By signaling the wakeup event for a time of 5 s for devices configured
as wakeup capable, we likely will be prevent a sleep long enough to let
user space consume the event.
To enable this feature, host drivers must thus configure their devices
as wakeup capable.
This is a reworked implementation of the old wakelocks for the mmc
subsystem, originally authored by Colin Cross and San Mehat for the
Android kernel. Zoran Markovic shall also be given cred for recently
re-trying to upstream this feature.
Cc: San Mehat <san@google.com>
Cc: Colin Cross <ccross@android.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Zoran Markovic <zoran.markovic@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Zoran Markovic <zoran.markovic@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Since mmc_select_voltage now only gets called from the attach sequence,
it makes sense to move the out of spec validations of the card ocr into
this function.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
According to eMMC/SD/SDIO specs, the VDD (VCC) voltage level must be
maintained during the initialization sequence. If we want/need to tune
the voltage level, a complete power cycle of the card must be executed.
Most host drivers conforms to the specifications by only allowing to
change VDD voltage level at the MMC_POWER_UP state, but some also cares
about MMC_POWER_ON state, which they should'nt. This patch will not
break those drivers, but they could clean up code to better reflect
what is expected from the protocol layer.
A big re-work of the mmc_select_voltage function is done to only change
VDD voltage level if the host supports MMC_CAP2_FULL_PWR_CYCLE.
Otherwise only validation of the host and card ocr mask will be done.
A very nice side-effect of this patch is that we now don't need to
reset the negotiated ocr mask at the mmc_power_off function, since now
it will actually reflect the present voltage level, which safely can be
used at the next power up and re-initialization. Moreover, we then only
need to execute mmc_select_voltage from the attach sequence.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
The negotiated ocr mask is directly related to the card. Once a card
gets removed, the mask shall be dropped. By moving the cache of the ocr
mask from the host struct to the card struct we have accomplished this.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
This is yet another step of restructure code to be able to fixup the
setup of the negotiated ocr mask.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
As a step to fixup the setup of the negotiated ocr mask, we need the
mmc_power_up|cycle functions to take the ocr as a parameter.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Some switch operations like poweroff notify, shall according to the
spec not be followed by any other new commands. For these cases and
when the host does'nt support MMC_CAP_WAIT_WHILE_BUSY, we must not
send status commands to poll for busy detection. Instead wait for
the stated timeout from the EXT_CSD before completing the request.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
cscope says there are no callers for mmc_try_claim_host in the kernel.
No reason to keep it.
Signed-off-by: Grant Grundler <grundler@chromium.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC updates from Chris Ball:
"MMC highlights for 3.12:
Core:
- Support Allocation Units 8MB-64MB in SD3.0, previous max was 4MB.
- The slot-gpio helper can now handle GPIO debouncing card-detect.
- Read supported voltages from DT "voltage-ranges" property.
Drivers:
- dw_mmc: Add support for ARC architecture, and support exynos5420.
- mmc_spi: Support CD/RO GPIOs.
- sh_mobile_sdhi: Add compatibility for more Renesas SoCs.
- sh_mmcif: Add DT support for DMA channels"
* tag 'mmc-updates-for-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (50 commits)
Revert "mmc: tmio-mmc: Remove .set_pwr() callback from platform data"
mmc: dw_mmc: Add support for ARC
mmc: sdhci-s3c: initialize host->quirks2 for using quirks2
mmc: sdhci-s3c: fix the wrong register value, when clock is disabled
mmc: esdhc: add support to get voltage from device-tree
mmc: sdhci: get voltage from sdhc host
mmc: core: parse voltage from device-tree
mmc: omap_hsmmc: use the generic config for omap2plus devices
mmc: omap_hsmmc: clear status flags before starting a new command
mmc: dw_mmc: exynos: Add a new compatible string for exynos5420
mmc: sh_mmcif: revision-specific CLK_CTRL2 handling
mmc: sh_mmcif: revision-specific Command Completion Signal handling
mmc: sh_mmcif: add support for Device Tree DMA bindings
mmc: sh_mmcif: move header include from header into .c
mmc: SDHI: add DT compatibility strings for further SoCs
mmc: dw_mmc-pci: enable bus-mastering mode
mmc: dw_mmc-pci: get resources from a proper BAR
mmc: tmio-mmc: Remove .set_pwr() callback from platform data
mmc: tmio-mmc: Remove .get_cd() callback from platform data
mmc: sh_mobile_sdhi: Remove .set_pwr() callback from platform data
...
|
|
Add function to support getting voltage from device-tree.
If voltage-range is specified in device-tree node, this function
will parse it and return the available voltage mask.
Signed-off-by: Haijun Zhang <haijun.zhang@freescale.com>
Acked-by: Anton Vorontsov <anton@enomsg.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Use regulator_get_optional() to tell the core that requests for the vmmcq
regulator can fail in a real system.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Chris Ball <cjb@laptop.org>
|
|
The host should be responsible to suspend|resume the host and not the
card. This patch changes this behaviour, by moving the responsiblity
to the mmc bus instead which already holds the card device.
The exported functions mmc_suspend|resume_host are now to be considered
as depcrecated. Once all host drivers moves away from using them, we
can remove them. As of now, a successful error code is always returned.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
By moving code from the mmc_suspend|resume_host down into each
.suspend|resume bus_ops callback, we get a more flexible solution.
Some nice side effects are that we get a better understanding of each
bus_ops suspend|resume sequence and the common code don't have to take
care of specific corner cases, especially for the SDIO case.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
This patch moves the validation for all the suspend prerequisites to be
done at SUSPEND_PREPARE notification. Previously in the SDIO case parts
of the validation was done from mmc_suspend_host.
This patch invents a new pre_suspend bus_ops callback and implements it
for SDIO. Returning an error code from it, will mean at SUSPEND_PREPARE
notification, the card will be removed before proceeding with the
suspend sequence.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
For every bus_ops type the .remove callback always exist, thus there
are no need to check the existence of it, before we decide to call it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
The mmc_card_sleep|awake APIs are not being used since the support is
already properly encapsulated within the suspend sequence. Sleep|awake
command is also specific for eMMC.
We remove the sleep|awake bus_ops, the mmc_card_sleep|awake APIs and
move the code into the mmc specific core instead. This also includes
the mmc ops function, mmc_sleepawake. All releated functions have then
become static and we have got far less code to maintain.
Additionally this patch also simplifies the code from mmc_sleepawake,
since it is only used to put the card to sleep and not awake.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Once the mmc blkdevice is being probed, runtime pm will be enabled.
By using runtime autosuspend, the power save operations can be done
when request inactivity occurs for a certain time. Right now the
selected timeout value is set to 3 s. Obviously this value will likely
need to be configurable somehow since it needs to be trimmed depending
on the power save algorithm.
For SD-combo cards, we are still leaving the enablement of runtime PM
to the SDIO init sequence since it depends on the capabilities of the
SDIO func driver.
Moreover, when the blk device is being suspended, we make sure the device
will be runtime resumed. The reason for doing this is that we want the
host suspend sequence to be unaware of any runtime power save operations
done for the card in this phase. Thus it can just handle the suspend as
the card is fully powered from a runtime perspective.
Finally, this patch prepares to make it possible to move BKOPS handling
into the runtime callbacks for the mmc bus_ops. Thus IDLE BKOPS can be
accomplished.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
SDIO is the only protocol that uses runtime pm for the card device
right now. To provide the option for sd and mmc to use runtime pm as
well the bus_ops callback are extended with two new functions. One for
runtime_suspend and one for runtime_resume.
This patch will also implement the callbacks for SDIO to make sure
existing functionality is maintained. It also prepares to move
away from using the mmc_power_restore_host API, since it is not
needed when using runtime PM.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Move mmc suspend specific operations to be executed from the .suspend
callback in the mmc bus_ops. This simplifies the mmc_suspend_host
function which is supposed to handle nothing but common suspend tasks.
Since eMMC can be considered non-removable there are no need to check
for ongoing bkops at PM_SUSPEND_PREPARE notification so remove it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
The sanitize support is added as a user-app ioctl call, and
was removed from the block-device request, since its purpose is
to be invoked not via File-System but by a user.
This feature deletes the unmap memory region of the eMMC card,
by writing to a specific register in the EXT_CSD.
unmap region is the memory region that was previously deleted
(by erase, trim or discard operation).
In order to avoid timeout when sanitizing large-scale cards,
the timeout for sanitize operation is 240 seconds.
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Previously the MMC_CAP2_DETECT_ON_ERR was invented for detecting
slow card removal. In was never a realy good solution and a proper
fix has been merged using gpio debouncing instead. We remove this
cap in this patch.
Although when using polling card detect mode, the code invented for
MMC_CAP2_DETECT_ON_ERR is re-used to complete card removal in an
earlier phase. There are no need waiting for the polling timeout to
elapse in this case.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Kevin Liu <kliu5@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC update from Chris Ball:
"MMC highlights for 3.10:
Core:
- Introduce MMC_CAP2_NO_PRESCAN_POWERUP to allow skipping
mmc_power_up() at boot/initialization time if it's already
happened, for performance (faster boot time) reasons.
- Fix a bit width test failure that resulted in old eMMC cards being
put into 1-bit mode when 4-bit mode was available.
- Expose fwrev/hwrev for MMCv4 parts.
- Improve card removal logic in the case where the card's removed
slowly; we were missing card removal events if the card retained
contact with the slot pads for long enough to reply to a CMD13
while being removed.
Drivers:
- davinci_mmc: Support using PIO instead of DMA.
- dw_mmc: Add support for Exynos4412.
- mxcmmc: DT support, use slot-gpio API.
- mxs-mmc: Add broken-cd/cd-inverted/non-removable DT property
support.
- sdhci-sirf: New sdhci-pltfm driver for CSR SiRF SoCs:
SiRFprimaII: unicore ARM Cortex-A9
SiRFatlas6: unicore ARM Cortex-A9
SiRFmarco: dual core ARM Cortex-A9 SMP
- sdhci-tegra: Add support for Tegra114 platforms, use
mmc_of_parse()"
* tag 'mmc-updates-for-3.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (66 commits)
mmc: sdhci-tegra: fix MODULE_DEVICE_TABLE
mmc: core: fix init controller performance regression, updated patch
mmc: mxcmmc: enable DMA support on mpc512x
mmc: mxcmmc: constify mxcmci_devtype
mmc: mxcmmc: use slot-gpio API for write-protect detection
mmc: mxcmmc: add mpc512x SDHC support
mmc: mxcmmc: fix race conditions for host->req and host->data access
mmc: mxcmmc: DT support
mmc: dw_mmc: let device core setup the default pin configuration
mmc: mxs-mmc: add broken-cd property
mmc: mxs-mmc: add non-removable property
mmc: mxs-mmc: add cd-inverted property
mmc: core: call pm_runtime_put_noidle in pm_runtime_get_sync failed case
mmc: mxcmmc: Fix bug when card is present during boot
mmc: core: fix performance regression initializing MMC host controllers
Revert "mmc: core: wait while adding MMC host to ensure root mounts successfully"
mmc: atmel-mci: pio hang on block errors
mmc: core: Fix bit width test failing on old eMMC cards
mmc: dw_mmc: Use pr_info instead of printk
mmc: dw_mmc: Check return value of regulator_enable
...
|
|
Use preferable function name which implies using a pseudo-random
number generator.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Chris Ball <cjb@laptop.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add MMC_CAP2_NO_PRESCAN_POWERUP to sdhci-pci.c also, use mmc_power_off()
for MMC_CAP2_NO_PRESCAN_POWERUP.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
[cjb: previously applied v1 of this patch instead of v4]
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Commit fa5501890d8974301042e0202d342a6cbe8609f4 introduced a performance
regression by adding mmc_power_up() to mmc_start_host(). mmc_power_up()
is not necessary to host controller initialization, it is part of card
initialization and is performed anyway asynchronously.
This patch allows a driver to leave the power up in asynchronous code
(as it was before).
On my current target platform this reduces driver initialization from:
[ 1.313220] initcall sdhci_acpi_driver_init+0x0/0x12 returned 0 after 102008 usecs
to this:
[ 1.217209] initcall sdhci_acpi_driver_init+0x0/0x12 returned 0 after 8331 usecs
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
successfully"
This reverts commit 3500ed90b26a9935b943b5e2e4cd3226600d6b58.
The reverted patch caused a significant performance regression when
booting with the root file system on eMMC.
Before the patch:
[ 1.625623] VFS: Mounted root (ext4 filesystem) readonly on device 179:2.
After the patch:
[ 1.935851] VFS: Mounted root (ext4 filesystem) readonly on device 179:2.
That was an addition of 310 ms which is a 19% performance degradation.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
MMC hosts are added asynchronously. We need to wait until detect returns to
avoid failed root filesystem mounts.
VFS: Cannot open root device "mmcblk0p1" or unknown-block(0,0): error -6
Please append a correct "root=" boot option; here are the available partitions:
mmc0: host does not support reading read-only switch. assuming write-enable.
1f00 256 mtdblock0 (driver?)
1f01 256 mtdblock1 (driver?)
1f02 2560 mtdblock2 mmc0: new SDHC card at address b368
(driver?)
1f03 29696 mtdblock3 (driver?)
1f04 16384 mtdblock4 mmcblk0: mmc0:b368 USD 3.72 GiB
(driver?)
mmcblk0: p1
b300 3910656 mmcblk0 driver: mmcblk
b301 3906560 mmcblk0p1 00000000-01
Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
Signed-off-by: Sergey Yanovich <ynvich@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Function _mmc_detect_card_removed will be called to know whether
the card is still present when host->bus_ops->detect is called.
In current code, the return value of this function generally only
depend on the result of sending cmd13 to card, which may not safe
for card with detection support like slot gpio detection.
Because the communication status between host and card may out of
sync with the detect status if remove the card slowly or hands shake
during the process. The direct reason is the async between card
detect switch and card/slot pad contaction in hardware, which is
defined by spec.
The spec define card insert/remove sequence as below (both standard size
SD card and MicroSD card have the same sequence):
"Part 1 Standard Size SD Card Mechanical Addendum Ver4.00 Final,
Appendix C: Card Detection Switch" (Take normally open type as example)
a)SD card insertion sequence:
The card detection switch should be turned on after all SD card
contact pads are connected to the host connector contact pads.
b)SD removal sequence:
The card detection switch should be turned off when the SD card
is just going to be removed and before any SD card contact pad is
disconnected from the host connector contact pad.
Below is the sequence when this issue occur (Take slot gpio detection
as example and remove the card slowly during the process):
1. gpio level changed and card detect interrupt triggered.
2. mmc_rescan was launched.
3. the card pads were still contacted with the slot pads because of slow
removal. So _mmc_detect_card_removed and mmc_rescan think card was
still present (cmd13 succeed).
4. card pads were discontacted from the card slot pads.
So the card was actually removed finally but the card removal event
has been missed by system.
The interval length between step 1 and step 4 depends on the
card removal speed. If it's longer than the detect work schedule
delay which is 200ms, this issue will likely happen.
This patch add the card detect status check in function
_mmc_detect_card_removed if cmd13 check succeed and host->ops->get_cd
provided. If get_cd detect no card present then schedule another detect
work 200ms later.
Signed-off-by: Kevin Liu <kliu5@marvell.com>
Tested-by: Johan Rudholm <johan.rudholm@stericsson.com>
Reviewed-by: Philip Rakity <prakity@nvidia.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
Adrian Hunter
Roger Tseng
Joe Perches
Chuanxiao Dong
Javier Martinez Canillas
Tim Kryger
Lukas Czerner
Tim Kryger
Seungwon Jeon
Stefan Wahren
Markus Mayer
Ulf Hansson
Sascha Hauer
Grant Grundler
Linus Torvalds
Haijun Zhang
Mark Brown
Maya Erez
Akinobu Mita
Sergey Yanovich
Kevin Liu