summaryrefslogtreecommitdiffstats
path: root/drivers/gpu/drm/nouveau/nouveau_bios.h
AgeCommit message (Collapse)Author
2012-03-22drm/nouveau: add bios connector type for dms59Ben Skeggs
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
2012-03-13drm/nouveau/bios: rework vbios shadowingBen Skeggs
Refactored to allow shadowing of VBIOS images longer than 64KiB, which allows us to pass the VBIOS checksum test on certain boards. There's also a workaround for reading the PROM VBIOS on some chipsets. Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
2012-03-13drm/nouveau: recognise DCB connector type for DP+DVI+VGA DMS-59Ben Skeggs
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
2012-02-01drm/nouveau/disp: check that panel power gpio is enabled at init timeBen Skeggs
Reported-by: Yuriy Khomchik <homyur@gmail.com> Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
2011-12-21drm/nouveau/gpio: reimplement as nouveau_gpio.c, fixing a number of issuesBen Skeggs
- moves out of nouveau_bios.c and demagics the logical state definitions - simplifies chipset-specific driver interface - makes most of gpio irq handling common, will use for nv4x hpd later - api extended to allow both direct gpio access, and access using the logical function states - api extended to allow for future use of gpio extender chips - pre-nv50 was handled very badly, the main issue being that all GPIOs were being treated as output-only. - fixes nvd0 so gpio changes actually stick, magic reg needs bashing Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
2011-12-21drm/nouveau/mxm: initial implementation of dcb sanitisationBen Skeggs
The DCB table provided by the VBIOS on most MXM chips has a number of entries which either need to be disabled, or modified according to the MXM-SIS Output Device Descriptors. The x86 vbios code usually takes care of this for us, however, with the large number of laptops now with switchable graphics or optimus, a lot of the time nouveau is responsible for POSTing the card instead - leaving some fun situations like, plugging in a monitor and having nouveau decide 3 connectors actually just got plugged in.. No MXM-SIS fetching methods implemented yet. Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
2011-12-21drm/nouveau/disp: parse connector info directly in nouveau_connector.cBen Skeggs
Another case where we parsed vbios data to some structs, then again use that info once to construct another set of data. Skip the intermediate step. This is also slightly improved in that we can now use DCB 3.x connector table info, which will allow NV4x to gain hotplug support, and to make quirks for SPWG LVDS panels unnecessary. Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
2011-12-21drm/nouveau/i2c: do parsing of i2c-related vbios info in nouveau_i2c.cBen Skeggs
Not much point parsing the vbios data into a struct which is only used once to parse the data into another struct, go directly from vbios to nouveau_i2c_chan. Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
2011-12-21drm/nouveau/bios: start refactoring dcb routinesBen Skeggs
This primary reason for this was mostly to avoid duplication of some of this stuff by the MXM-SIS parser. However, some other cleanups will also follow this as a result. Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
2011-12-21drm/nouveau/bios: pass drm_device to ROMPTR, rather than nvbiosBen Skeggs
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
2011-12-21drm/nv50/pm: s/PLL_UNK05/PLL_VDEC/Martin Peres
Following to "drm/nv50/pm: s/unk05/vdec/", let's rename the PLL to PLL_VDEC PLL names are purely indicative and are based on the most important engine it clocks. Signed-off-by: Martin Peres <martin.peres@labri.fr> Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
2011-12-21drm/nouveau/gpio: remove invert flag, use state[] everywhereBen Skeggs
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
2011-12-21drm/nouveau/pm: manual pwm fanspeed management for nv40+ boardsMartin Peres
Exposes the following sysfs entries: - fan0_input: read the rotational speed of the fan (poll a bit during 250ms) - pwm0: set the pwm duty cycle - pwm0_min/max: set the minimum/maximum pwm value v2 (Ben Skeggs): - nv50 pwm controller code removed in favour of other more complete code - FAN_RPM -> FAN_SENSE - merged FAN_SENSE readout into common code, not at all nv50-specific - protected fanspeed changes with perflvl_wr - formatting tidying - added some comments where things are shaky v3 (Martin Peres) - ensure duty min/max from thermal table are sane Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Martin Peres <martin.peres@ensi-bourges.fr>
2011-09-20drm/nouveau/dp: return master dp table pointer too when looking up encoderBen Skeggs
Will need to be able to distinguish 2.0/2.1 from 3.0 soon. Also, move the vbios parsing to nouveau_dp where it belongs. Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
2011-09-20drm/nouveau/bios: allow passing in crtc to the init table parserBen Skeggs
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
2011-05-16drm/nouveau: recognise DCB connector type 0x41 as LVDSBen Skeggs
After looking at a number of different logs, it appears 0x41 likely indicates the presense of an LVDS panel following the SPWG spec (http://www.spwg.org/) Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
2011-02-25drm/nouveau: make vbios parser runnable from an atomic contextBen Skeggs
The nv50 display isr bh needs to be converted to a tasklet, which means we can't sleep anymore. The places we execute vbios init tables are rare, and not in any way performance critical, so this isn't a huge problem. Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
2010-09-24drm/nouveau: make bios code easier to use externallyBen Skeggs
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
2010-09-24drm/nouveau: make the behaviour of get_pll_limits() consistentBen Skeggs
This replaces all the pll_types definitions for ones that match the types used in the tables in recent VBIOS versions. get_pll_limits() will now accept either type or register value as input across all limits table versions, and will store the actual register ID that a PLL type refers to in the returned structure. Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
2010-08-26drm/nv50: add dcb type 14 to enum to prevent compiler complaintBen Skeggs
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
2010-08-06drm/nv17-nv4x: Attempt to init some external TMDS transmitters.Francisco Jerez
sil164 and friends are the most common, usually they just need to be poked once because a fixed configuration is enough for any modes and clocks, so they worked without this patch if the BIOS had done a good job on POST. Display couldn't survive a suspend/resume cycle though. Unfortunately, BIOS scripts are useless here. Signed-off-by: Francisco Jerez <currojerez@riseup.net> Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
2010-07-26drm/nv04-nv3x: Implement init-compute-mem.Francisco Jerez
Init-compute-mem was the last piece missing for nv0x-nv3x card cold-booting. This implementation is somewhat lacking but it's been reported to work on most chipsets it was tested in. Let me know if it breaks suspend to RAM for you. Signed-off-by: Francisco Jerez <currojerez@riseup.net> Tested-by: Patrice Mandin <patmandin@gmail.com> Tested-by: Ben Skeggs <bskeggs@redhat.com> Tested-by: Xavier Chantry <chantry.xavier@gmail.com> Tested-by: Marcin Kościelnicki <koriakin@0x04.net> Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
2010-07-26drm/nouveau: support fetching LVDS EDID from ACPIBen Skeggs
Based on a patch from Matthew Garrett. Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Acked-by: Matthew Garrett <mjg@redhat.com>
2010-07-13drm/nouveau: tidy connector/encoder creation a littleBen Skeggs
Create connectors before encoders to avoid having to do another loop across encoder list whenever we create a new connector. This allows us to pass the connector to the encoder creation functions, and avoid using a create_resources() callback since we can now call it directly. This can also potentially modify the connector ordering on nv50. On cards where the DCB connector and encoder tables are in the same order, things will be unchanged. However, there's some cards where the ordering between the tables differ, and in one case, leads us to naming the connectors "wrongly". Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
2010-05-19drm/nv50: store full dcb i2c entry from vbiosBen Skeggs
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
2010-04-09drm/nv50: parse/use some more de-magiced parts of gpio table entriesBen Skeggs
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
2010-04-09drm/nouveau: store raw gpio table entry in bios gpio structsBen Skeggs
And use our own version of the GPIO table for the INIT_GPIO opcode. Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
2010-04-09drm/nv40: rework lvds table parsingBen Skeggs
All indications seem to be that the version 0x30 table should be handled the same way as 0x40 (as used on G80), at least for the parts that we currently try use. This commit cleans up the parsing to make it clearer about what we're actually trying to achieve, and unifies the 0x30/0x40 parsing. Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
2010-03-10drm/nv50: fix connector table parsing for some cardsBen Skeggs
The connector table index in the DCB entry for each output type is an index into the connector table, and does *not* necessarily match up with what was previously called "index" in the connector table entries themselves. Not real sure what that index is exactly, renamed to "index2" as we still use it to prevent creating multiple TV connectors. Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
2010-02-25drm/nouveau: check for known dcb connector typesBen Skeggs
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
2010-02-25drm/nouveau: reorganise bios header, add dcb connector type enumsBen Skeggs
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
2010-02-25drm/nouveau: merge nvbios and nouveau_bios_infoBen Skeggs
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
2010-02-25drm/nouveau: merge parsed_dcb and bios_parsed_dcb into dcb_tableBen Skeggs
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
2010-02-25drm/nouveau: rename parsed_dcb_gpio to dcb_gpio_tableBen Skeggs
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
2010-02-16drm/nouveau: use mutex for vbios lockBen Skeggs
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
2010-02-10drm/nv50: prevent multiple init tables being parsed at the same timeBen Skeggs
With DVI and DP plugged, the DVI clock change interrupts being run can cause DP link training to fail. This adds a spinlock around init table parsing to prevent this. Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
2009-12-16drm/nouveau: Kill global state in BIOS script interpreterMarcin Kościelnicki
Signed-off-by: Marcin Kościelnicki <koriakin@0x04.net> Signed-off-by: Maarten Maathuis <madman2003@gmail.com> Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
2009-12-11drm/nouveau: Add DRM driver for NVIDIA GPUsBen Skeggs
This adds a drm/kms staging non-API stable driver for GPUs from NVIDIA. This driver is a KMS-based driver and requires a compatible nouveau userspace libdrm and nouveau X.org driver. This driver requires firmware files not available in this kernel tree, interested parties can find them via the nouveau project git archive. This driver is reverse engineered, and is in no way supported by nVidia. Support for nearly the complete range of nvidia hw from nv04->g80 (nv50) is available, and the kms driver should support driving nearly all output types (displayport is under development still) along with supporting suspend/resume. This work is all from the upstream nouveau project found at nouveau.freedesktop.org. The original authors list from nouveau git tree is: Anssi Hannula <anssi.hannula@iki.fi> Ben Skeggs <bskeggs@redhat.com> Francisco Jerez <currojerez@riseup.net> Maarten Maathuis <madman2003@gmail.com> Marcin Kościelnicki <koriakin@0x04.net> Matthew Garrett <mjg@redhat.com> Matt Parnell <mparnell@gmail.com> Patrice Mandin <patmandin@gmail.com> Pekka Paalanen <pq@iki.fi> Xavier Chantry <shiningxc@gmail.com> along with project founder Stephane Marchesin <marchesin@icps.u-strasbg.fr> Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
generated by cgit 1.2.3-korg (git 2.39.0) at 2024-06-08 13:23:31 +0000