| Age | Commit message (Collapse) | Author |
|---|
|
commit e3c9d9d6ebfeeeee29c6240e1b5978d40d31d21f upstream.
Since commit fa93fd4ecc9c ("regulator: core: Ensure we are at least in
bounds for our constraints") the imx53-qsb board populated with a Dialog
DA9053 PMIC fails to boot:
LDO3: Bringing 3300000uV into 1800000-1800000uV
The LDO3 voltage constraints passed in the device tree do not match
the valid range according to the datasheet, so fix this accordingly to
allow the board booting again.
While at it, fix the other voltage constraints as well.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1b283eea6228880b765bc40fe4e555416437ce58 upstream.
This fixes a very annoying regression on the Snowball SD card
that has been around for a while. It turns out that the device
tree does not configure the direction pins properly, nor sets
up the pins for the voltage converter properly at boot. Unless
all things are correctly set up, the feedback clock will not
work, and makes the driver spew messages in the console (but
it works, very slowly):
root@Ux500:/ mount /dev/mmcblk0p2 /mnt/
[ 9.953460] mmci-pl18x 80126000.sdi0_per1: error during DMA transfer!
[ 9.960296] mmcblk0: error -110 sending status command, retrying
[ 9.966461] mmcblk0: error -110 sending status command, retrying
[ 9.972534] mmcblk0: error -110 sending status command, aborting
Fix this by rectifying the device tree to correspond to that of
the Ux500 HREF boards plus the DAT31DIR setting that is unique for
the Snowball, and things start working smoothly. Add in the SDR12
and SDR25 modes which this host can do without any problems.
I don't know if this has ever been correct, sadly. It works after
this patch.
Reported-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0b965a13ad81fa895e534d1f50b355ff8b0b3ed3 upstream.
Commit b8d368caa8dc ("ARM: dts: omap3: overo: remove unneded unit names
in display nodes") removed the unit names for all Overo display nodes
that didn't have a reg property.
But the display in arch/arm/boot/dts/omap3-overo-common-lcd35.dtsi does
have a reg property so the correct fix was to make the unit name match
the value of the reg property, instead of removing it.
This patch fixes the following DTC warning for boards using this dtsi:
"ocp/spi@48098000/display has a reg or ranges property, but no unit name"
Fixes: b8d368caa8dc ("ARM: dts: omap3: overo: remove unneded unit names in display nodes")
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c4ad72560df11961d3e57fb0fadfe88a9863c9ad upstream.
The ethernet version in the earlier RealView EB variants is
LAN91C111 and not LAN9118 according to ARM DUI 0303E
"RealView Emulation Baseboard User Guide" page 3-57.
Make sure that this is used for the base variant of the board.
As the DT bindings for LAN91C111 does not specify any power
supplies, these need to be deleted from the DTS file.
Fixes: 2440d29d2ae2 ("ARM: dts: realview: support all the RealView EB board variants")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c53beb47f621e4a56f31af9f86470041655516c7 upstream.
The BCM958625HR board has 2GB of RAM available. Increase the amount
from 512MB to 2GB and add the device type to the memory entry.
Fixes: 9a4865d42fe5 ("ARM: dts: NSP: Specify RAM amount for BCM958625HR board")
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 06ad11be7a9e13499ff8e55e46f09d22f9ee6fc0 upstream.
The R_PIO device node is missing #interrupt-cells, which causes
interrupt parsing to fail to match it as a valid interrupt controller.
Add #interrupt-cells to it. Also remove the unnecesary #address-cells
and #size-cells.
Fixes: 1ac56a6da9e1 ("ARM: dts: sun9i: Add A80 R_PIO pin controller device
node")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit dcf5907e0e09a160a57160729f920add5df8e358 upstream.
The Qualcomm SPMI GPIO and MPP lines are problematic: the
are fetched from the main MFD driver with platform_get_irq()
which means that at this point they will all be assigned the
flags set up for the interrupts in the device tree.
That is problematic since these are flagged as rising edge
and an this point the interrupt descriptor is assigned a
rising edge, while the only thing the GPIO/MPP drivers really
do is issue irq_get_irqchip_state() on the line to read it
out and to provide a .to_irq() helper for *other* IRQ
consumers.
If another device tree node tries to flag the same IRQ
for use as something else than rising edge, the kernel
irqdomain core will protest like this:
type mismatch, failed to map hwirq-NN for <FOO>!
Which is what happens when the device tree defines two
contradictory flags for the same interrupt line.
To work around this and alleviate the problem, assign 0
as flag for the interrupts taken by the PM GPIO and MPP
drivers. This will lead to the flag being unset, and a
second consumer requesting rising, falling, both or level
interrupts will be respected. This is what the qcom-pm*.dtsi
files already do.
Switched to using the symbolic name IRQ_TYPE_NONE so that
we get this more readable.
This misconfiguration was caused by a copy/pasting the
APQ8064 set-up, the latter has been fixed in a separate
patch.
Tested with one of the SPMI GPIOs: after this I can
successfully request one of these GPIOs as falling edge
from the device tree.
Fixes: 0840ea9e4457 ("ARM: dts: add GPIO and MPP to MSM8660 PMIC")
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Björn Andersson <bjorn.andersson@linaro.org>
Cc: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ca88696e8b73a9fa2b1de445747e9235c3a7bd50 upstream.
The Qualcomm PMIC GPIO and MPP lines are problematic: the
are fetched from the main MFD driver with platform_get_irq()
which means that at this point they will all be assigned the
flags set up for the interrupts in the device tree.
That is problematic since these are flagged as rising edge
and an this point the interrupt descriptor is assigned a
rising edge, while the only thing the GPIO/MPP drivers really
do is issue irq_get_irqchip_state() on the line to read it
out and to provide a .to_irq() helper for *other* IRQ
consumers.
If another device tree node tries to flag the same IRQ
for use as something else than rising edge, the kernel
irqdomain core will protest like this:
type mismatch, failed to map hwirq-NN for <FOO>!
Which is what happens when the device tree defines two
contradictory flags for the same interrupt line.
To work around this and alleviate the problem, assign 0
as flag for the interrupts taken by the PM GPIO and MPP
drivers. This will lead to the flag being unset, and a
second consumer requesting rising, falling, both or level
interrupts will be respected. This is what the qcom-pm*.dtsi
files already do.
Switched to using the symbolic name IRQ_TYPE_NONE so that
we get this more readable.
Fixes: bce360469676 ("ARM: dts: apq8064: add pm8921 mpp support")
Fixes: 874443fe9e33 ("ARM: dts: apq8064: Add pm8921 mfd and its gpio node")
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Björn Andersson <bjorn.andersson@linaro.org>
Cc: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 061492cfad9f11dbc32df741a7164f307b69b6e6 upstream.
The armada-390.dtsi was broken since the first patch which adds Device Tree
files for Armada 39x SoC was introduced.
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Fixes 538da83 ("ARM: mvebu: add Device Tree files for Armada 39x SoC and board")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
Pull ARM fixes from Russell King:
"Three relatively small fixes for ARM:
- Roger noticed that dma_max_pfn() was calculating the upper limit
wrongly, by adding the PFN offset of memory twice.
- A fix from Robin to correct parsing of MPIDR values when the
address size is larger than one BE32 unit.
- A fix from Srinivas to ensure that we do not rely on the boot
loader (or previous Linux kernel) setting the translation table
base register a certain way in the decompressor, which can lead to
crashes"
* 'fixes' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 8618/1: decompressor: reset ttbcr fields to use TTBR0 on ARMv7
ARM: 8617/1: dma: fix dma_max_pfn()
ARM: 8616/1: dt: Respect property size when parsing CPUs
|
|
If the bootloader uses the long descriptor format and jumps to
kernel decompressor code, TTBCR may not be in a right state.
Before enabling the MMU, it is required to clear the TTBCR.PD0
field to use TTBR0 for translation table walks.
The commit dbece45894d3a ("ARM: 7501/1: decompressor:
reset ttbcr for VMSA ARMv7 cores") does the reset of TTBCR.N, but
doesn't consider all the bits for the size of TTBCR.N.
Clear TTBCR.PD0 field and reset all the three bits of TTBCR.N to
indicate the use of TTBR0 and the correct base address width.
Fixes: dbece45894d3 ("ARM: 7501/1: decompressor: reset ttbcr for VMSA ARMv7 cores")
Acked-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Srinivas Ramana <sramana@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"Here are a couple of bugfixes for v4.8-rc.
Most of them have actually been around for a while this time but for
some reason didn't get applied early on. The shmobile regulator fix
is the only one that isn't completely obvious.
Device tree changes:
- archtimer interrupts must be level triggered (multiple platforms)
- fix for USB and MMC clocks on STiH410
- fix split DT repository in case of raspberry-pi 3
- a new use of skeleton.dtsi on arm64 has crept in after that was
removed.
defconfig updates:
- xilinx vdma has a new Kconfig symbol name
- keystone requires CONFIG_NOP_USB_XCEIV since v4.8-rc1
Code fixes:
- fix regulator quirk on shmobile
- suspend-to-ram regression on EXYNOS
Maintainer updates:
- Javier Martinez Canillas is now a reviewer for Samsung EXYNOS"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: keystone: defconfig: Fix USB configuration
arm64: dts: Fix broken architected timer interrupt trigger
ARM: multi_v7_defconfig: update XILINX_VDMA
ARM64: dts: bcm: Use a symlink to R-Pi dtsi files from arch=arm
ARM: dts: Remove use of skeleton.dtsi from bcm283x.dtsi
ARM: dts: STiH407-family: Provide interconnect clock for consumption in ST SDHCI
ARM: dts: STiH410: Handle interconnect clock required by EHCI/OHCI (USB)
ARM: shmobile: fix regulator quirk for Gen2
ARM: EXYNOS: Clear OF_POPULATED flag from PMU node in IRQ init callback
MAINTAINERS: Add myself as reviewer for Samsung Exynos support
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pchotard/sti into fixes
Pull "Handle STiH410 interconnect clock required for EHCI/OHCI and SDHCI" from Patrice Chotard:
With the introduction of critical-clock support in v4.8, our developers'
default configuration is to run with 'clk_ignore_unused' removed. This
patch-set ensures they can achieve successful boot when a) booting from
an SD Card and when b) booting using USB->Eth adaptors for NFS booting.
* tag 'sti-dt-fixes-for-v4.8-rcs' of git://git.kernel.org/pub/scm/linux/kernel/git/pchotard/sti:
ARM: dts: STiH407-family: Provide interconnect clock for consumption in ST SDHCI
ARM: dts: STiH410: Handle interconnect clock required by EHCI/OHCI (USB)
|
|
This file is included from DTS files under arch/arm64 too (via
broadcom/bcm2837-rpi-3-b.dts and broadcom/bcm2837.dtsi). There is a desire
not to have skeleton.dtsi for ARM64. See commit 3ebee5a2e141 ("arm64: dts:
kill skeleton.dtsi") for rationale for its removal.
As well as the addition of #*-cells also requires adding the device_type to
the rpi memory node explicitly.
Note that this change results in the removal of an empty /aliases node from
bcm2835-rpi-a.dtb and bcm2835-rpi-a-plus.dtb. I have no hardware to check
if this is a problem or not.
It also results in some reordering of the nodes in the DTBs (the /aliases
and /memory nodes come later). This isn't supposed to matter but, again,
I've no hardware to check if it is true in this particular case.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Frank Rowand <frowand.list@gmail.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Lee Jones <lee@kernel.org>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-rpi-kernel@lists.infradead.org
Cc: arm@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"This is a slightly larger batch of fixes that we've been sitting on a
few -rcs. Most of them are simple oneliners, but there are two sets
that are slightly larger and worth pointing out:
- A set of patches to OMAP to deal with hwmod for RTC on am33xx
(beaglebone SoC, among others). It's the only clock that ever has
a valid offset of 0, so a new flag needed introduction once this
problem was discovered.
- A collection of CCI fixes for performance counters discovered once
people started using it on X-Gene CPUs"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (37 commits)
arm-cci: pmu: Fix typo in event name
Revert "ARM: tegra: fix erroneous address in dts"
ARM: dts: imx6qdl: Fix SPDIF regression
ARM: imx6: add missing BM_CLPCR_BYPASS_PMIC_READY setting for imx6sx
ARM: dts: imx7d-sdb: fix ti,x-plate-ohms property name
ARM: dts: kirkwood: Fix PCIe label on OpenRD
ARM: kirkwood: ib62x0: fix size of u-boot environment partition
bus: arm-ccn: make event groups reliable
bus: arm-ccn: fix hrtimer registration
bus: arm-ccn: fix PMU interrupt flags
ARM: tegra: Correct polarity for Tegra114 PMIC interrupt
MAINTAINERS: add tree entry for ARM/UniPhier architecture
ARM: sun5i: Fix typo in trip point temperature
MAINTAINERS: Switch to kernel.org account for Krzysztof Kozlowski
ARM: imx6ul: populates platform device at .init_machine
bus: arm-ccn: Add missing event attribute exclusions for host/guest
bus: arm-ccn: Correct required arguments for XP PMU events
bus: arm-ccn: Fix XP watchpoint settings bitmask
bus: arm-ccn: Do not attempt to configure XPs for cycle counter
bus: arm-ccn: Fix PMU handling of MN
...
|
|
The STiH4{07,10} platform contains some interconnect clocks which are used
by various IPs. If these clocks aren't handled correctly by ST's SDHCI
driver MMC will break and the following output can be observed:
[ 13.916949] mmc0: Timeout waiting for hardware interrupt.
[ 13.922349] sdhci: =========== REGISTER DUMP (mmc0)===========
[ 13.928175] sdhci: Sys addr: 0x00000000 | Version: 0x00001002
[ 13.933999] sdhci: Blk size: 0x00007040 | Blk cnt: 0x00000001
[ 13.939825] sdhci: Argument: 0x00fffff0 | Trn mode: 0x00000013
[ 13.945650] sdhci: Present: 0x1fff0206 | Host ctl: 0x00000011
[ 13.951475] sdhci: Power: 0x0000000f | Blk gap: 0x00000080
[ 13.957300] sdhci: Wake-up: 0x00000000 | Clock: 0x00003f07
[ 13.963126] sdhci: Timeout: 0x00000004 | Int stat: 0x00000000
[ 13.968952] sdhci: Int enab: 0x02ff008b | Sig enab: 0x02ff008b
[ 13.974777] sdhci: AC12 err: 0x00000000 | Slot int: 0x00000000
[ 13.980602] sdhci: Caps: 0x21ed3281 | Caps_1: 0x00000000
[ 13.986428] sdhci: Cmd: 0x0000063a | Max curr: 0x00000000
[ 13.992252] sdhci: Host ctl2: 0x00000000
[ 13.996166] sdhci: ADMA Err: 0x00000000 | ADMA Ptr: 0x7c048200
[ 14.001990] sdhci: ===========================================
[ 14.009802] mmc0: Got data interrupt 0x02000000 even though no data operation was in progress.
Cc: stable@vger.kernel.org
Tested-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
|
|
The STiH4{07,10} platform contains some interconnect clocks which are used
by various IPs. If this clock isn't handled correctly by ST's EHCI/OHCI
drivers, their hub won't be found, the following error be shown and the
result will be non-working USB:
[ 97.221963] hub 2-1:1.0: hub_ext_port_status failed (err = -110)
Cc: stable@vger.kernel.org
Tested-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into fixes
Allwinner fixes for 4.8
A single patch fixing a typo in the temperature trip points in the A13
DTSI.
* tag 'sunxi-fixes-for-4.8' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
ARM: sun5i: Fix typo in trip point temperature
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
i.MX fixes for 4.8, 2nd round:
- Fix misspelled "ti,x-plate-ohms" property name of touchscreen
controller for imx7d-sdb DTS.
- Add missing BM_CLPCR_BYPASS_PMIC_READY setting for i.MX6SX to get
suspend/resume work properly.
- Fix SPDIF regression on imx6qdl which caused by a clock update on
spdif device node.
* tag 'imx-fixes-4.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx6qdl: Fix SPDIF regression
ARM: imx6: add missing BM_CLPCR_BYPASS_PMIC_READY setting for imx6sx
ARM: dts: imx7d-sdb: fix ti,x-plate-ohms property name
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
This reverts commit b5c86b7496d74f6e454bcab5166efa023e1f0459.
This is no longer needed due to other changes going into 4.8 to rename
the unit addresses on a large number of device nodes. So it was picked up
for v4.8-rc1 in error.
Reported-by: Ralf Ramsauer <ralf@ramses-pyramidenbau.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Commit 833f2cbf7091 ("ARM: dts: imx6: change the core clock of spdif")
changed many more clocks than only the SPDIF core clock as stated in
the commit message.
The MLB clock has been added and this causes SPDIF regression as
reported by Xavi Drudis Ferran and also in this forum post:
https://forum.digikey.com/thread/34240
The MX6Q Reference Manual does not mention that MLB is a clock related
to SPDIF, so change it back to a dummy clock to restore SPDIF
functionality.
Thanks to Ambika for providing the fix at:
https://community.nxp.com/thread/387131
Fixes: 833f2cbf7091 ("ARM: dts: imx6: change the core clock of spdif")
Cc: <stable@vger.kernel.org> # 4.4.x
Reported-by: Xavi Drudis Ferran <xdrudis@tinet.cat>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Xavi Drudis Ferran <xdrudis@tinet.cat>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Merge "mvebu fixes for 4.8 (part 1)" from Gregory CLEMENT:
Few device tree fix on kirkwood:
- enable PCIe on OpenRD
- use correct u-boot environment partition size on ib62x0
* tag 'mvebu-fixes-4.8-2' of git://git.infradead.org/linux-mvebu:
ARM: dts: kirkwood: Fix PCIe label on OpenRD
ARM: kirkwood: ib62x0: fix size of u-boot environment partition
|
|
Fix misspelled "ti,x-plate-ohms" property name of TI TSC2046
touchscreen controller.
Fixes: d09e6beafa23 ("ARM: dts: imx7d-sdb: Add support for touchscreen")
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
While converting PCIe node on kirkwood by using label, the following
commit eb13cf8345e9 ("ARM: dts: kirkwood: Fixup pcie DT warnings")
introduced a regression on the OpenRD boards: the PCIe didn't work
anymore. As reported by Aaro Koskinen, the display/framebuffer was
lost. This commit adds the forgotten label.
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Fixes: eb13cf8345e9 ("ARM: dts: kirkwood: Fixup pcie DT warnings")
Cc: stable@vger.kernel.org
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
Commit 148c274ea644 ("ARM: kirkwood: ib62x0: add u-boot environment
partition") split the "u-boot" partition into "u-boot" and "u-boot
environment". However, instead of the size of the environment, an offset
was given, resulting in overlapping partitions.
Signed-off-by: Simon Baatz <gmbnomis@gmail.com>
Fixes: 148c274ea644 ("ARM: kirkwood: ib62x0: add u-boot environment partition")
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Cc: Luka Perkov <luka@openwrt.org>
Cc: stable@vger.kernel.org # 3.13+
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
The ARM GIC only supports interrupts with either level-high or
rising-edge types for SPIs. The interrupt type for the Palmas PMIC used
for Tegra114 boards is specified as level-low which is invalid for the
GIC. This has gone undetected because until recently, failures to set
the interrupt type when the interrupts are mapped via firmware (such as
device-tree) have not been reported. Since commits 4b357daed698
("genirq: Look-up trigger type if not specified by caller") and
1e2a7d78499e ("irqdomain: Don't set type when mapping an IRQ"), failure
to set the interrupt type will cause the requesting of the interrupt to
fail and exposing incorrectly configured interrupts.
Please note that although the interrupt type was never being set for the
Palmas PMIC, it was still working fine, because the default type setting
for the interrupt, 'level-high', happen to match the correct type for
the interrupt.
Finally, it should be noted that the Palmas interrupt from the PMIC is
actually 'level-low', however, this interrupt signal is inverted by the
Tegra PMC and so the GIC actually sees a 'level-high' interrupt which is
what should be specified in the device-tree interrupt specifier.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into fixes
Fix for v4.8-rc1:
1. Select proper eMMC HighSpeed mode on Odroid XU. DTS was mixing
"samsung,exynos5250-dw-mshc" compatible (with HS200 as fastest mode)
with a property "mmc-hs400-1_8v" thus leading to failures during
probe.
2. Update Krzysztof Kozlowski's email address in maintainers.
* tag 'samsung-fixes-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
MAINTAINERS: Switch to kernel.org account for Krzysztof Kozlowski
ARM: dts: exynos: Properly select eMMC HighSpeed mode on Odroid XU
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
The i.MX fixes for 4.8:
- Fix typo in imx6sx-sabreauto board wakeup property
- Fix i.MX6UL suspend-to-standby support by adding the
BM_CLPCR_BYP_MMDC_CH0_LPM_HS handling
- Fix a i.MX6UL regression on suspend support, which is caused by
commit 850bea2335e4 ("arm: Remove unnecessary of_platform_populate
with default match table")
* tag 'imx-fixes-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: imx6ul: populates platform device at .init_machine
ARM: imx6: add missing BM_CLPCR_BYP_MMDC_CH0_LPM_HS setting for imx6ul
ARM: dts: imx6sx-sabreauto: Fix misspelled property
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Fixes for omaps for v4.8-rc cycle, mostly a series of four fixes for
am335x RTC zero offset for clkctrl register. Also few other fixes:
- Add missing sysc information for DSI as at least n950 needs it for
the working display
- Fix old elm-id properties that cause nand boot to not work
- Fix overo gpmc nand cs0 range
- FIx overo gpmc nand on boards with ethernet
- Fix logicpd torpedo nand ready pin nand interrupt configuration
* tag 'omap-for-v4.8/fixes-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: logicpd-somlv: Fix NAND device nodes
ARM: dts: logicpd-torpedo-som: Provide NAND ready pin
ARM: dts: overo: fix gpmc nand on boards with ethernet
ARM: dts: overo: fix gpmc nand cs0 range
ARM: dts: am335x: Update elm phandle binding
ARM: OMAP4+: CM: Remove redundant checks for clkctrl_offs of zero
ARM: OMAP4+: Have _omap4_wait_target_* check for valid clkctrl_offs
ARM: OMAP2+: AM33XX: Add HWMOD_OMAP4_ZERO_CLKCTRL_OFFSET flag to rtc hwmod
ARM: OMAP4+: hwmod: Add hwmod flag for HWMOD_OMAP4_ZERO_CLKCTRL_OFFSET
ARM: OMAP3: hwmod data: Add sysc information for DSI
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
mvebu fixes for 4.8 (part 1)
Fix lan numbering for the Armada 388 clearfog board
* tag 'mvebu-fixes-4.8-1' of git://git.infradead.org/linux-mvebu:
ARM: dts: armada-388-clearfog: number LAN ports properly
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
SARADC controller needs to be reset before programming it, otherwise
it will not function properly.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Set cpu_alert0 temperature to 85°C instead of 850°C.
Fixes: 32a5d2d170cc ("ARM: dts: sun5i: Add cpu thermal zones to dtsi")
Signed-off-by: Hugo Grostabussiat <bonstra@bonstra.fr.eu.org>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
This fix was applied to a bunch of omap3 devices including LogicPD
Torpedo, but this got missed since it was new around the same times
the patches were applied. This makes the GPMC parameters match the
Torpedo since they have the same processor PoP memory.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This was applied to a variety of omap3 boards, so it should
probably be applied here. I did not test NAND performance, but
I tested this with UBI to confirm read/write didn't break.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The gpmc ranges property for NAND at CS0 was being overridden by later
includes that defined gpmc ethernet nodes, effectively breaking NAND on
these systems:
omap-gpmc 6e000000.gpmc: /ocp/gpmc@6e000000/nand@0,0 has
malformed 'reg' property
Instead of redefining the NAND range in every such dtsi, define all
currently used ranges in omap3-overo-base.dtsi.
Fixes: 98ce6007efb4 ("ARM: dts: overo: Support PoP NAND")
Cc: stable <stable@vger.kernel.org> # 4.3
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The gpmc ranges property for NAND at CS0 has been broken since it was
first added.
This currently prevents the nand gpmc child node from being probed:
omap-gpmc 6e000000.gpmc: /ocp/gpmc@6e000000/nand@0,0 has
malformed 'reg' property
and consequently the NAND device from being registered.
Fixes: 98ce6007efb4 ("ARM: dts: overo: Support PoP NAND")
Cc: stable <stable@vger.kernel.org> # 4.3
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The check for the "elm_id" binding had been removed.
This causes nand boot to fail on boards still using
the old binding. Update the bindings on those boards.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Clearly QEMU is very permissive in how its PL310 model may be set up,
but the real hardware turns out to be far more particular about things
actually being correct. Fix up the DT description so that the real
thing actually boots:
- The arm,data-latency and arm,tag-latency properties need 3 cells to
be valid, otherwise we end up retaining the default 8-cycle latencies
which leads pretty quickly to lockup.
- The arm,dirty-latency property is only relevant to L210/L220, so get
rid of it.
- The cache geometry override also leads to lockup and/or general
misbehaviour. Irritatingly, the manual doesn't state the actual PL310
configuration, but based on the boardfile code and poking registers
from the Boot Monitor, it would seem to be 8 sets of 16KB ways.
With that, we can successfully boot to enjoy the fun of mismatched FPUs...
Cc: stable@vger.kernel.org
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
c90bb7b enabled the high speed UARTs of the Jetson TK1. Due to a merge
quirk, wrong addresses were introduced. Fix it and use the correct
addresses.
Thierry let me know, that there is another patch (b5896f67ab3c in
linux-next) in preparation which removes all the '0,' prefixes of unit
addresses on Tegra124 and is planned to go upstream in 4.8, so
this patch will get reverted then.
But for the moment, this patch is necessary to fix current misbehaviour.
Fixes: c90bb7b9b9 ("ARM: tegra: Add high speed UARTs to Jetson TK1 device tree")
Signed-off-by: Ralf Ramsauer <ralf@ramses-pyramidenbau.de>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Cc: stable@vger.kernel.org # v4.7
Cc: linux-tegra@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
This syscon needs to be looked up by clocks, flash protection
and other consumers.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
This syscon needs to be looked up by flash protection, CLCD
display output settings and other consumers.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Exynos5410 supports eMMC version 4.41 so HS200 is the top mode which
should be configured. This is reflected in usage of
"samsung,exynos5250-dw-mshc" compatible. However Odroid XU DTS
contained also property "mmc-hs400-1_8v" which is parsed by MMC core
therefore resulting in mixed configuration. MMC core set HS400 but
dwmmc_exynos driver did not configure the data strobe for HS400 DDR
mode.
Removal of HS400 properties fixes semi-random mmc errors during boot:
mmc_host mmc0: Bus speed (slot 0) = 400000000Hz (slot req 200000000Hz, actual 200000000HZ div = 1)
mmc0: mmc_select_hs400 failed, error -84
mmc0: error -84 whilst initialising MMC card
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
|
|
In commit 99fc5ba0bfb6 ("ARM: dts: imx6sx: add i.mx6sx sabreauto board
support") it should've been enable-sdio-wakeup (not -wakup). But that is
now considered a legacy name for wakeup-source, so directly use the new
name instead, as done in commit 26cefdd15db1 for the other occurrence.
Fixes: 26cefdd15db1 ("ARM: dts: imx: replace legacy wakeup property with 'wakeup-source'")
Signed-off-by: Andreas Färber <afaerber@suse.de>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Currently, the ports as seen from the rear number as:
eth0 sfp lan5 lan4 lan3 lan2 lan1 lan6
which is illogical - this came about because the rev 2.0 boards have the
LEDs on the front for the DSA switch (lan5-1) reversed. Rev 2.1 boards
fixed the LED issue, and the Clearfog case numbers the lan ports
increasing from left to right.
Maintaining this illogical numbering causes confusion, with reports that
"my link isn't coming up" and "my connection negotiates 10base-Half"
both of which are due to people thinking that the port next to the SFP
is lan1.
Fix this by renumbering the ports to match people's expectations.
[gregory.clement@free-electrons.com: added the Fixes and stable tags]
Fixes: 4c945e8556ec ("ARM: dts: Add SolidRun Armada 388 Clearfog A1 DT
file")
Cc: <stable@vger.kernel.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
This commit adds definition for cpu_on, cpu_off and cpu_suspend
commands. These definitions must match the corresponding PSCI
definitions in boot monitor.
Having those command and corresponding PSCI support in boot monitor
allows run time CPU hot plugin.
Link: http://lkml.kernel.org/r/E1b8koV-0004Hf-2j@rmk-PC.armlinux.org.uk
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Pratyush Anand <panand@redhat.com>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Dave Young <dyoung@redhat.com>
Cc: Baoquan He <bhe@redhat.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Simon Horman <horms@verge.net.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Olof Johansson:
"Device tree contents continue to be the largest branches we submit.
This time around, some of the contents worth pointing out is:
New SoC platforms:
- Freescale i.MX 7Solo
- Broadcom BCM23550
- Cirrus Logic EP7209 and EP7211 (clps711x platforms)_
- Hisilicon HI3519
- Renesas R8A7792
Some of the other delta that is sticking out, line-count wise:
- Exynos moves of IP blocks under an SoC bus, which causes a large
delta due to indentation changes
- a new Tegra K1 board: Apalis
- a bunch of small updates to many Allwinner platforms; new hardware
support, some cleanup, etc"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (426 commits)
ARM: dts: sun8i: Add dts file for inet86dz board
ARM: dts: sun8i: Add dts file for Polaroid MID2407PXE03 tablet
ARM: dts: sun8i: Use sun8i-reference-design-tablet for ga10h dts
ARM: dts: sun8i: Use sun8i-reference-design-tablet for polaroid mid2809pxe04
ARM: dts: sun8i: reference-design-tablet: Add drivevbus-supply
ARM: dts: Copy sun8i-q8-common.dtsi sun8i-reference-design-tablet.dtsi
ARM: dts: sun5i: Use sun5i-reference-design-tablet.dtsi for utoo p66 dts
ARM: dts: sun5i: Use sun5i-reference-design-tablet.dtsi for dit4350 dts
ARM: dts: sun5i: reference-design-tablet: Remove mention of q8
ARM: dts: sun5i: reference-design-tablet: Set lradc vref to avcc
ARM: dts: sun5i: Rename sun5i-q8-common.dtsi sun5i-reference-design-tablet.dtsi
ARM: dts: sun5i: Move q8 display bits to sun5i-a13-q8-tablet.dts
ARM: dts: sunxi: Rename sunxi-q8-common.dtsi sunxi-reference-design-tablet.dtsi
ARM: dts: at91: Don't build unnecessary dtbs
ARM: dts: at91: sama5d3x: separate motherboard gmac and emac definitions
ARM: dts: at91: at91sam9g25ek: fix isi endpoint node
ARM: dts: at91: move isi definition to at91sam9g25ek
ARM: dts: at91: fix i2c-gpio node name
ARM: dts: at91: vinco: fix regulator name
ARM: dts: at91: ariag25 : fix onewire node
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"Driver updates for ARM SoCs.
A slew of changes this release cycle. The reset driver tree, that we
merge through arm-soc for historical reasons, is also sizable this
time around.
Among the changes:
- clps711x: Treewide changes to compatible strings, merged here for simplicity.
- Qualcomm: SCM firmware driver cleanups, move to platform driver
- ux500: Major cleanups, removal of old mach-specific infrastructure.
- Atmel external bus memory driver
- Move of brcmstb platform to the rest of bcm
- PMC driver updates for tegra, various fixes and improvements
- Samsung platform driver updates to support 64-bit Exynos platforms
- Reset controller cleanups moving to devm_reset_controller_register() APIs
- Reset controller driver for Amlogic Meson
- Reset controller driver for Hisilicon hi6220
- ARM SCPI power domain support"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (100 commits)
ARM: ux500: consolidate base platform files
ARM: ux500: move soc_id driver to drivers/soc
ARM: ux500: call ux500_setup_id later
ARM: ux500: consolidate soc_device code in id.c
ARM: ux500: remove cpu_is_u* helpers
ARM: ux500: use CLK_OF_DECLARE()
ARM: ux500: move l2x0 init to .init_irq
mfd: db8500 stop passing around platform data
ASoC: ab8500-codec: remove platform data based probe
ARM: ux500: move ab8500_regulator_plat_data into driver
ARM: ux500: remove unused regulator data
soc: raspberrypi-power: add CONFIG_OF dependency
firmware: scpi: add CONFIG_OF dependency
video: clps711x-fb: Changing the compatibility string to match with the smallest supported chip
input: clps711x-keypad: Changing the compatibility string to match with the smallest supported chip
pwm: clps711x: Changing the compatibility string to match with the smallest supported chip
serial: clps711x: Changing the compatibility string to match with the smallest supported chip
irqchip: clps711x: Changing the compatibility string to match with the smallest supported chip
clocksource: clps711x: Changing the compatibility string to match with the smallest supported chip
clk: clps711x: Changing the compatibility string to match with the smallest supported chip
...
|
|
Pull watchdog updates from Wim Van Sebroeck:
"Core:
- min and max timeout improvements, WDOG_HW_RUNNING improvements,
status funtionality
- Add a device managed API for watchdog_register_device()
New watchdog drivers:
- Aspeed SoCs
- Maxim PMIC MAX77620
- Amlogic Meson GXBB SoC
Enhancements:
- support for the r8a7796 watchdog device
- support for F81866 watchdog device
- support for 5th variation of Apollo Lake
- support for MCP78S chipset
- clean-up of softdog.c watchdog device driver
- pic32-wdt and pic32-dmt fixes
- Documentation/watchdog: watchdog-test improvements
- several other fixes and improvements"
* git://www.linux-watchdog.org/linux-watchdog: (50 commits)
watchdog: gpio_wdt: Fix missing platform_set_drvdata() in gpio_wdt_probe()
watchdog: core: Clear WDOG_HW_RUNNING before calling the stop function
watchdog: core: Fix error handling of watchdog_dev_init()
watchdog: pic32-wdt: Fix return value check in pic32_wdt_drv_probe()
watchdog: pic32-dmt: Remove .owner field for driver
watchdog: pic32-wdt: Remove .owner field for driver
watchdog: renesas-wdt: Add support for the r8a7796 wdt
Documentation/watchdog: check return value for magic close
watchdog: sbsa: Drop status function
watchdog: Implement status function in watchdog core
watchdog: tangox: Set max_hw_heartbeat_ms instead of max_timeout
watchdog: change watchdog_need_worker logic
watchdog: add support for MCP78S chipset in nv_tco
watchdog: bcm2835_wdt: remove redundant ->set_timeout callback
watchdog: bcm2835_wdt: constify _ops and _info structures
dt-bindings: watchdog: Add Meson GXBB Watchdog bindings
watchdog: Add Meson GXBB Watchdog Driver
watchdog: qcom: configure BARK time in addition to BITE time
watchdog: qcom: add option for standalone watchdog not in timer block
watchdog: qcom: update device tree bindings
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DeviceTree updates from Rob Herring:
- remove most of_platform_populate() calls in arch code. Now the DT
core code calls it in the default case and platforms only need to
call it if they have special needs
- use pr_fmt on all the DT core print statements
- CoreSight binding doc improvements to block name descriptions
- add dt_to_config script which can parse dts files and list
corresponding kernel config options
- fix memory leak hit with a PowerMac DT
- correct a bunch of STMicro compatible strings to use the correct
vendor prefix
- fix DA9052 PMIC binding doc to match what is actually used in dts
files
* tag 'devicetree-for-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (35 commits)
documentation: da9052: Update regulator bindings names to match DA9052/53 DTS expectations
xtensa: Partially Revert "xtensa: Remove unnecessary of_platform_populate with default match table"
xtensa: Fix build error due to missing include file
MIPS: ath79: Add missing include file
Fix spelling errors in Documentation/devicetree
ARM: dts: fix STMicroelectronics compatible strings
powerpc/dts: fix STMicroelectronics compatible strings
Documentation: dt: i2c: use correct STMicroelectronics vendor prefix
scripts/dtc: dt_to_config - kernel config options for a devicetree
of: fdt: mark unflattened tree as detached
of: overlay: add resolver error prints
coresight: document binding acronyms
Documentation/devicetree: document cavium-pip rx-delay/tx-delay properties
of: use pr_fmt prefix for all console printing
of/irq: Mark initialised interrupt controllers as populated
of: fix memory leak related to safe_name()
Revert "of/platform: export of_default_bus_match_table"
of: unittest: use of_platform_default_populate() to populate default bus
memory: omap-gpmc: use of_platform_default_populate() to populate default bus
bus: uniphier-system-bus: use of_platform_default_populate() to populate default bus
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Michael Turquette:
"The bulk of the changes are updates and fixes to existing clk provider
drivers, along with a pretty standard number of new drivers. The core
recieved a small number of updates as well.
Core changes of note:
- removed CLK_IS_ROOT flag
New clk provider drivers:
- Renesas r8a7796 clock pulse generator / module standby and
software reset
- Allwinner sun8i H3 clock controller unit
- AmLogic meson8b clock controller (rewritten)
- AmLogic gxbb clock controller
- support for some new ICs was added by simple changes to static
data tables for chips sharing the same family
Driver updates of note:
- the Allwinner sunxi clock driver infrastucture was rewritten to
comform to the state of the art at drivers/clk/sunxi-ng. The old
implementation is still supported for backwards compatibility with
the DT ABI"
* tag 'clk-for-linus-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (162 commits)
clk: Makefile: re-sort and clean up
Revert "clk: gxbb: expose CLKID_MMC_PCLK"
clk: samsung: Allow modular build of the Audio Subsystem CLKCON driver
clk: samsung: make clk-s5pv210-audss explicitly non-modular
clk: exynos5433: remove CLK_IGNORE_UNUSED flag from SPI clocks
clk: oxnas: Add hardware dependencies
clk: imx7d: do not set parent of ethernet time/ref clocks
ARM: dt: sun8i: switch the H3 to the new CCU driver
clk: sunxi-ng: h3: Fix Kconfig symbol typo
clk: sunxi-ng: h3: Fix audio clock divider offset
clk: sunxi-ng: Add H3 clocks
clk: sunxi-ng: Add N-K-M-P factor clock
clk: sunxi-ng: Add N-K-M Factor clock
clk: sunxi-ng: Add N-M-factor clock support
clk: sunxi-ng: Add N-K-factor clock support
clk: sunxi-ng: Add M-P factor clock support
clk: sunxi-ng: Add divider
clk: sunxi-ng: Add phase clock support
clk: sunxi-ng: Add mux clock support
clk: sunxi-ng: Add gate clock support
...
|
Fabio Estevam
Linus Walleij
Javier Martinez Canillas
Jon Mason
Chen-Yu Tsai
Grzegorz Jaszczyk
Linus Torvalds
Srinivas Ramana
Arnd Bergmann
Ian Campbell
Lee Jones
Olof Johansson
Vladimir Zapolskiy
Gregory CLEMENT
Simon Baatz
Jon Hunter
Caesar Wang
Hugo Grostabussiat
Adam Ford
Johan Hovold
Teresa Remmet
Robin Murphy
Ralf Ramsauer
Krzysztof Kozlowski
Andreas Färber
Russell King
Vitaly Andrianov