| Age | Commit message (Collapse) | Author |
|---|
|
Replaces the per-packet multipath with a hash-based multipath using
source and destination address.
Signed-off-by: Peter Nørlund <pch@ordbogen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
net/dsa/slave.c
net/dsa/slave.c simply had overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The fib_table_lookup tracepoint found 2 places where the flowi4_flags is
not initialized.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace calls to vrf_dev_get_rth with l3mdev_get_rtable.
The check on the flow flags is handled in the l3mdev operation.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace calls to vrf_master_ifindex_rcu and vrf_master_ifindex with either
l3mdev_master_ifindex_rcu or l3mdev_master_ifindex.
The pattern:
oif = vrf_master_ifindex(dev) ? : dev->ifindex;
is replaced with
oif = l3mdev_fib_oif(dev);
And remove the now unused vrf macros.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Rename IFF_VRF_MASTER to IFF_L3MDEV_MASTER and update the name of the
netif_is_vrf and netif_index_is_vrf macros.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
err is initialized to -EINVAL when it is declared. It is not reset until
fib_lookup which is well after the 3 users of the martian_source jump. So
resetting err to -EINVAL at martian_source label is not needed.
Removing that line obviates the need for the martian_source_keep_err label
so delete it.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch just swaps the ordering of one of the conditional tests in
ip_route_input_mc. Specifically it swaps the testing for the source
address to see if it is loopback, and the test to see if we allow a
loopback source address.
The reason for swapping these two tests is because it is much faster to
test if an address is loopback than it is to dereference several pointers
to get at the net structure to see if the use of loopback is allowed.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
net/ipv4/arp.c
The net/ipv4/arp.c conflict was one commit adding a new
local variable while another commit was deleting one.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Very soon, TCP stack might call inet_csk_route_req(), which
calls inet_csk_route_req() with an unlocked listener socket,
so we need to make sure ip_route_output_flow() is not trying to
change any field from its socket argument.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Man page of ip-route(8) says following about route types:
unreachable - these destinations are unreachable. Packets are dis‐
carded and the ICMP message host unreachable is generated. The local
senders get an EHOSTUNREACH error.
blackhole - these destinations are unreachable. Packets are dis‐
carded silently. The local senders get an EINVAL error.
prohibit - these destinations are unreachable. Packets are discarded
and the ICMP message communication administratively prohibited is
generated. The local senders get an EACCES error.
In the inet6 address family, this was correct, except the local senders
got ENETUNREACH error instead of EHOSTUNREACH in case of unreachable route.
In the inet address family, all three route types generated ICMP message
net unreachable, and the local senders got ENETUNREACH error.
In both address families all three route types now behave consistently
with documentation.
Signed-off-by: Nikola Forró <nforro@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Sergey, Richard and Fabio reported an oops in ip_route_input_noref. e.g., from Richard:
[ 0.877040] BUG: unable to handle kernel NULL pointer dereference at 0000000000000056
[ 0.877597] IP: [<ffffffff8155b5e2>] ip_route_input_noref+0x1a2/0xb00
[ 0.877597] PGD 3fa14067 PUD 3fa6e067 PMD 0
[ 0.877597] Oops: 0000 [#1] SMP
[ 0.877597] Modules linked in: virtio_net virtio_pci virtio_ring virtio
[ 0.877597] CPU: 1 PID: 119 Comm: ifconfig Not tainted 4.2.0+ #1
[ 0.877597] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
[ 0.877597] task: ffff88003fab0bc0 ti: ffff88003faa8000 task.ti: ffff88003faa8000
[ 0.877597] RIP: 0010:[<ffffffff8155b5e2>] [<ffffffff8155b5e2>] ip_route_input_noref+0x1a2/0xb00
[ 0.877597] RSP: 0018:ffff88003ed03ba0 EFLAGS: 00010202
[ 0.877597] RAX: 0000000000000046 RBX: 00000000ffffff8f RCX: 0000000000000020
[ 0.877597] RDX: ffff88003fab50b8 RSI: 0000000000000200 RDI: ffffffff8152b4b8
[ 0.877597] RBP: ffff88003ed03c50 R08: 0000000000000000 R09: 0000000000000000
[ 0.877597] R10: 0000000000000000 R11: 0000000000000000 R12: ffff88003fab6f00
[ 0.877597] R13: ffff88003fab5000 R14: 0000000000000000 R15: ffffffff81cb5600
[ 0.877597] FS: 00007f6de5751700(0000) GS:ffff88003ed00000(0000) knlGS:0000000000000000
[ 0.877597] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 0.877597] CR2: 0000000000000056 CR3: 000000003fa6d000 CR4: 00000000000006e0
[ 0.877597] Stack:
[ 0.877597] 0000000000000000 0000000000000046 ffff88003fffa600 ffff88003ed03be0
[ 0.877597] ffff88003f9e2c00 697da8c0017da8c0 ffff880000000000 000000000007fd00
[ 0.877597] 0000000000000000 0000000000000046 0000000000000000 0000000400000000
[ 0.877597] Call Trace:
[ 0.877597] <IRQ>
[ 0.877597] [<ffffffff812bfa1f>] ? cpumask_next_and+0x2f/0x40
[ 0.877597] [<ffffffff8158e13c>] arp_process+0x39c/0x690
[ 0.877597] [<ffffffff8158e57e>] arp_rcv+0x13e/0x170
[ 0.877597] [<ffffffff8151feec>] __netif_receive_skb_core+0x60c/0xa00
[ 0.877597] [<ffffffff81515795>] ? __build_skb+0x25/0x100
[ 0.877597] [<ffffffff81515795>] ? __build_skb+0x25/0x100
[ 0.877597] [<ffffffff81521ff6>] __netif_receive_skb+0x16/0x70
[ 0.877597] [<ffffffff81522078>] netif_receive_skb_internal+0x28/0x90
[ 0.877597] [<ffffffff8152288f>] napi_gro_receive+0x7f/0xd0
[ 0.877597] [<ffffffffa0017906>] virtnet_receive+0x256/0x910 [virtio_net]
[ 0.877597] [<ffffffffa0017fd8>] virtnet_poll+0x18/0x80 [virtio_net]
[ 0.877597] [<ffffffff815234cd>] net_rx_action+0x1dd/0x2f0
[ 0.877597] [<ffffffff81053228>] __do_softirq+0x98/0x260
[ 0.877597] [<ffffffff8164969c>] do_softirq_own_stack+0x1c/0x30
The root cause is use of res.table uninitialized.
Thanks to Nikolay for noticing the uninitialized use amongst the maze of
gotos.
As Nikolay pointed out the second initialization is not required to fix
the oops, but rather to fix a related problem where a valid lookup should
be invalidated before creating the rth entry.
Fixes: b7503e0cdb5d ("net: Add FIB table id to rtable")
Reported-by: Sergey Senozhatsky <sergey.senozhatsky.work@gmail.com>
Reported-by: Richard Alpe <richard.alpe@ericsson.com>
Reported-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Tested-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
rt_fill_info which is called for 'route get' requests hardcodes the
table id as RT_TABLE_MAIN which is not correct when multiple tables
are used. Use the newly added table id in the rtable to send back
the correct table similar to what is done for IPv6.
To maintain current ABI a new request flag, RTM_F_LOOKUP_TABLE, is
added to indicate the actual table is wanted versus the hardcoded
response.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the FIB table id to rtable to make the information available for
IPv4 as it is for IPv6.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All callers to rt_dst_alloc have nearly the same initialization following
a successful allocation. Consolidate it into rt_dst_alloc.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The mode field holds a single bit of information only (whether the
ip_tunnel_info struct is for rx or tx). Change the mode field to bit flags.
This allows more mode flags to be added.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
inetpeer caches based on address only, so duplicate IP addresses within
a namespace return the same cached entry. Enhance the ipv4 address key
to contain both the IPv4 address and VRF device index.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, the lwtunnel state resides in per-protocol data. This is
a problem if we encapsulate ipv6 traffic in an ipv4 tunnel (or vice versa).
The xmit function of the tunnel does not know whether the packet has been
routed to it by ipv4 or ipv6, yet it needs the lwtstate data. Moving the
lwtstate data to dst_entry makes such inter-protocol tunneling possible.
As a bonus, this brings a nice diffstat.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds the capability to redirect dst input in the same way
that dst output is redirected by LWT.
Also, save the original dst.input and and dst.out when setting up
lwtunnel redirection. These can be called by the client as a pass-
through.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As with ingress use the index of VRF master device for route lookups on
egress. However, the oif should only be used to direct the lookups to a
specific table. Routes in the table are not based on the VRF device but
rather interfaces that are part of the VRF so do not consider the oif for
lookups within the table. The FLOWI_FLAG_VRFSRC is used to control this
latter part.
Signed-off-by: Shrijeet Mukherjee <shm@cumulusnetworks.com>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On ingress use index of VRF master device for route lookups if real device
is enslaved. Rules are expected to be installed for the VRF device to
direct lookups to a specific table.
Signed-off-by: Shrijeet Mukherjee <shm@cumulusnetworks.com>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
lwtunnel encap is applied for forwarded packets, but not for
locally-generated packets. This is because the output function is not
overridden in __mkroute_output, unlike it is in __mkroute_input.
The lwtunnel state is correctly set on the rth through the call to
rt_set_nexthop, so all that needs to be done is to override the dst
output function to be lwtunnel_output if there is lwtunnel state
present and it requires output redirection.
Signed-off-by: Robert Shearman <rshearma@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
arch/s390/net/bpf_jit_comp.c
drivers/net/ethernet/ti/netcp_ethss.c
net/bridge/br_multicast.c
net/ipv4/ip_fragment.c
All four conflicts were cases of simple overlapping
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It saves some lines and simplify a bit the code when the state is returning
by this function. It's also useful to handle a NULL entry.
To avoid too long lines, I've also renamed lwtunnel_state_get() and
lwtunnel_state_put() to lwtstate_get() and lwtstate_put().
CC: Thomas Graf <tgraf@suug.ch>
CC: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
fib_select_default considers alternative routes only when
res->fi is for the first alias in res->fa_head. In the
common case this can happen only when the initial lookup
matches the first alias with highest TOS value. This
prevents the alternative routes to require specific TOS.
This patch solves the problem as follows:
- routes that require specific TOS should be returned by
fib_select_default only when TOS matches, as already done
in fib_table_lookup. This rule implies that depending on the
TOS we can have many different lists of alternative gateways
and we have to keep the last used gateway (fa_default) in first
alias for the TOS instead of using single tb_default value.
- as the aliases are ordered by many keys (TOS desc,
fib_priority asc), we restrict the possible results to
routes with matching TOS and lowest metric (fib_priority)
and routes that match any TOS, again with lowest metric.
For example, packet with TOS 8 can not use gw3 (not lowest
metric), gw4 (different TOS) and gw6 (not lowest metric),
all other gateways can be used:
tos 8 via gw1 metric 2 <--- res->fa_head and res->fi
tos 8 via gw2 metric 2
tos 8 via gw3 metric 3
tos 4 via gw4
tos 0 via gw5
tos 0 via gw6 metric 1
Reported-by: Hagen Paul Pfeifer <hagen@jauu.net>
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This introduces a new IP tunnel lightweight tunnel type which allows
to specify IP tunnel instructions per route. Only IPv4 is supported
at this point.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a new flowi_tunnel structure which is a subset of ip_tunnel_key to
allow routes to match on tunnel metadata. For now, the tunnel id is
added to flowi_tunnel which allows for routes to be bound to specific
virtual tunnels.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Introduces a new dst_metadata which enables to carry per packet metadata
between forwarding and processing elements via the skb->dst pointer.
The structure is set up to be a union. Thus, each separate type of
metadata requires its own dst instance. If demand arises to carry
multiple types of metadata concurrently, metadata dst entries can be
made stackable.
The metadata dst entry is refcnt'ed as expected for now but a non
reference counted use is possible if the reference is forced before
queueing the skb.
In order to allow allocating dsts with variable length, the existing
dst_alloc() is split into a dst_alloc() and dst_init() function. The
existing dst_init() function to initialize the subsystem is being
renamed to dst_subsys_init() to make it clear what is what.
The check before ip_route_input() is changed to ignore metadata dsts
and drop the dst inside the routing function thus allowing to interpret
metadata in a later commit.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For input routes with tunnel encap state this patch redirects
dst output functions to lwtunnel_output which later resolves to
the corresponding lwtunnel output function.
This has been tested to work with mpls ip tunnels.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds support in ipv4 fib functions to parse user
provided encap attributes and attach encap state data to fib_nh
and rtable.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
flags local variable in __mkroute_input is not used as a variable.
Signed-off-by: Masatake YAMATO <yamato@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This feature is only enabled with the new per-interface or ipv4 global
sysctls called 'ignore_routes_with_linkdown'.
net.ipv4.conf.all.ignore_routes_with_linkdown = 0
net.ipv4.conf.default.ignore_routes_with_linkdown = 0
net.ipv4.conf.lo.ignore_routes_with_linkdown = 0
...
When the above sysctls are set, will report to userspace that a route is
dead and will no longer resolve to this nexthop when performing a fib
lookup. This will signal to userspace that the route will not be
selected. The signalling of a RTNH_F_DEAD is only passed to userspace
if the sysctl is enabled and link is down. This was done as without it
the netlink listeners would have no idea whether or not a nexthop would
be selected. The kernel only sets RTNH_F_DEAD internally if the
interface has IFF_UP cleared.
With the new sysctl set, the following behavior can be observed
(interface p8p1 is link-down):
default via 10.0.5.2 dev p9p1
10.0.5.0/24 dev p9p1 proto kernel scope link src 10.0.5.15
70.0.0.0/24 dev p7p1 proto kernel scope link src 70.0.0.1
80.0.0.0/24 dev p8p1 proto kernel scope link src 80.0.0.1 dead linkdown
90.0.0.0/24 via 80.0.0.2 dev p8p1 metric 1 dead linkdown
90.0.0.0/24 via 70.0.0.2 dev p7p1 metric 2
90.0.0.1 via 70.0.0.2 dev p7p1 src 70.0.0.1
cache
local 80.0.0.1 dev lo src 80.0.0.1
cache <local>
80.0.0.2 via 10.0.5.2 dev p9p1 src 10.0.5.15
cache
While the route does remain in the table (so it can be modified if
needed rather than being wiped away as it would be if IFF_UP was
cleared), the proper next-hop is chosen automatically when the link is
down. Now interface p8p1 is linked-up:
default via 10.0.5.2 dev p9p1
10.0.5.0/24 dev p9p1 proto kernel scope link src 10.0.5.15
70.0.0.0/24 dev p7p1 proto kernel scope link src 70.0.0.1
80.0.0.0/24 dev p8p1 proto kernel scope link src 80.0.0.1
90.0.0.0/24 via 80.0.0.2 dev p8p1 metric 1
90.0.0.0/24 via 70.0.0.2 dev p7p1 metric 2
192.168.56.0/24 dev p2p1 proto kernel scope link src 192.168.56.2
90.0.0.1 via 80.0.0.2 dev p8p1 src 80.0.0.1
cache
local 80.0.0.1 dev lo src 80.0.0.1
cache <local>
80.0.0.2 dev p8p1 src 80.0.0.1
cache
and the output changes to what one would expect.
If the sysctl is not set, the following output would be expected when
p8p1 is down:
default via 10.0.5.2 dev p9p1
10.0.5.0/24 dev p9p1 proto kernel scope link src 10.0.5.15
70.0.0.0/24 dev p7p1 proto kernel scope link src 70.0.0.1
80.0.0.0/24 dev p8p1 proto kernel scope link src 80.0.0.1 linkdown
90.0.0.0/24 via 80.0.0.2 dev p8p1 metric 1 linkdown
90.0.0.0/24 via 70.0.0.2 dev p7p1 metric 2
Since the dead flag does not appear, there should be no expectation that
the kernel would skip using this route due to link being down.
v2: Split kernel changes into 2 patches, this actually makes a
behavioral change if the sysctl is set. Also took suggestion from Alex
to simplify code by only checking sysctl during fib lookup and
suggestion from Scott to add a per-interface sysctl.
v3: Code clean-ups to make it more readable and efficient as well as a
reverse path check fix.
v4: Drop binary sysctl
v5: Whitespace fixups from Dave
v6: Style changes from Dave and checkpatch suggestions
v7: One more checkpatch fixup
Signed-off-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: Dinesh Dutt <ddutt@cumulusnetworks.com>
Acked-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
drivers/net/ethernet/cadence/macb.c
drivers/net/phy/phy.c
include/linux/skbuff.h
net/ipv4/tcp.c
net/switchdev/switchdev.c
Switchdev was a case of RTNH_H_{EXTERNAL --> OFFLOAD}
renaming overlapping with net-next changes of various
sorts.
phy.c was a case of two changes, one adding a local
variable to a function whilst the second was removing
one.
tcp.c overlapped a deadlock fix with the addition of new tcp_info
statistic values.
macb.c involved the addition of two zyncq device entries.
skbuff.h involved adding back ipv4_daddr to nf_bridge_info
whilst net-next changes put two other existing members of
that struct into a union.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ip_error does not check if in_dev is NULL before dereferencing it.
IThe following sequence of calls is possible:
CPU A CPU B
ip_rcv_finish
ip_route_input_noref()
ip_route_input_slow()
inetdev_destroy()
dst_input()
With the result that a network device can be destroyed while processing
an input packet.
A crash was triggered with only unicast packets in flight, and
forwarding enabled on the only network device. The error condition
was created by the removal of the network device.
As such it is likely the that error code was -EHOSTUNREACH, and the
action taken by ip_error (if in_dev had been accessible) would have
been to not increment any counters and to have tried and likely failed
to send an icmp error as the network device is going away.
Therefore handle this weird case by just dropping the packet if
!in_dev. It will result in dropping the packet sooner, and will not
result in an actual change of behavior.
Fixes: 251da4130115b ("ipv4: Cache ip_error() routes even when not forwarding.")
Reported-by: Vittorio Gambaletta <linuxbugs@vittgam.net>
Tested-by: Vittorio Gambaletta <linuxbugs@vittgam.net>
Signed-off-by: Vittorio Gambaletta <linuxbugs@vittgam.net>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In setups with a global scope address on an interface, and a lesser
scope address on an interface sending IGMP reports, the reports can be
sent using the other interfaces global scope address rather than the
local interface address. RFC 2236 suggests:
Ignore the Report if you cannot identify the source address of
the packet as belonging to a subnet assigned to the interface on
which the packet was received.
since such reports could be forged.
Look at the protocol when deciding if a RT_SCOPE_LINK address should
be used for the packet.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Merge net into net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Under stress, ip_idents_reserve() is accessing a contended
cache line twice, with non optimal MESI transactions.
If we place timestamps in separate location, we reduce this
pressure by ~50% and allow atomic_add_return() to issue
a Request for Ownership.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The commit 3cdaa5be9e81a914e633a6be7b7d2ef75b528562 ("ipv4: Don't
increase PMTU with Datagram Too Big message") broke PMTU in cases
where the rt_pmtu value has expired but is smaller than the new
PMTU value.
This obsolete rt_pmtu then prevents the new PMTU value from being
installed.
Fixes: 3cdaa5be9e81 ("ipv4: Don't increase PMTU with Datagram Too Big message")
Reported-by: Gerd v. Egidy <gerd.von.egidy@intra2net.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ipv4 code uses a mixture of coding styles. In some instances check
for non-NULL pointer is done as x != NULL and sometimes as x. x is
preferred according to checkpatch and this patch makes the code
consistent by adopting the latter form.
No changes detected by objdiff.
Signed-off-by: Ian Morris <ipm@chirality.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ipv4 code uses a mixture of coding styles. In some instances check
for NULL pointer is done as x == NULL and sometimes as !x. !x is
preferred according to checkpatch and this patch makes the code
consistent by adopting the latter form.
No changes detected by objdiff.
Signed-off-by: Ian Morris <ipm@chirality.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Those are counterparts to nla_put_in_addr and nla_put_in6_addr.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
IP addresses are often stored in netlink attributes. Add generic functions
to do that.
For nla_put_in_addr, it would be nicer to pass struct in_addr but this is
not used universally throughout the kernel, in way too many places __be32 is
used to store IPv4 address.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As namespaces are sometimes used with overlapping ip address ranges,
we should also use the namespace as input to the hash to select the ip
fragmentation counter bucket.
Cc: Eric Dumazet <edumazet@google.com>
Cc: Flavio Leitner <fbl@redhat.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After my change to neigh_hh_init to obtain the protocol from the
neigh_table there are no more users of protocol in struct dst_ops.
Remove the protocol field from dst_ops and all of it's initializers.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
drivers/net/vxlan.c
drivers/vhost/net.c
include/linux/if_vlan.h
net/core/dev.c
The net/core/dev.c conflict was the overlap of one commit marking an
existing function static whilst another was adding a new function.
In the include/linux/if_vlan.h case, the type used for a local
variable was changed in 'net', whereas the function got rewritten
to fix a stacked vlan bug in 'net-next'.
In drivers/vhost/net.c, Al Viro's iov_iter conversions in 'net-next'
overlapped with an endainness fix for VHOST 1.0 in 'net'.
In drivers/net/vxlan.c, vxlan_find_vni() added a 'flags' parameter
in 'net-next' whereas in 'net' there was a bug fix to pass in the
correct network namespace pointer in calls to this function.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
RFC 1191 said, "a host MUST not increase its estimate of the Path
MTU in response to the contents of a Datagram Too Big message."
Signed-off-by: Li Wei <lw@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
arch/arm/boot/dts/imx6sx-sdb.dts
net/sched/cls_bpf.c
Two simple sets of overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Not caching dst_entries which cause redirects could be exploited by hosts
on the same subnet, causing a severe DoS attack. This effect aggravated
since commit f88649721268999 ("ipv4: fix dst race in sk_dst_get()").
Lookups causing redirects will be allocated with DST_NOCACHE set which
will force dst_release to free them via RCU. Unfortunately waiting for
RCU grace period just takes too long, we can end up with >1M dst_entries
waiting to be released and the system will run OOM. rcuos threads cannot
catch up under high softirq load.
Attaching the flag to emit a redirect later on to the specific skb allows
us to cache those dst_entries thus reducing the pressure on allocation
and deallocation.
This issue was discovered by Marcelo Leitner.
Cc: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Marcelo Leitner <mleitner@redhat.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 053c095a82cf ("netlink: make nlmsg_end() and genlmsg_end()
void") didn't catch all of the cases where callers were breaking out
on the return value being equal to zero, which they no longer should
when zero means success.
Fix all such cases.
Reported-by: Marcel Holtmann <marcel@holtmann.org>
Reported-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Contrary to common expectations for an "int" return, these functions
return only a positive value -- if used correctly they cannot even
return 0 because the message header will necessarily be in the skb.
This makes the very common pattern of
if (genlmsg_end(...) < 0) { ... }
be a whole bunch of dead code. Many places also simply do
return nlmsg_end(...);
and the caller is expected to deal with it.
This also commonly (at least for me) causes errors, because it is very
common to write
if (my_function(...))
/* error condition */
and if my_function() does "return nlmsg_end()" this is of course wrong.
Additionally, there's not a single place in the kernel that actually
needs the message length returned, and if anyone needs it later then
it'll be very easy to just use skb->len there.
Remove this, and make the functions void. This removes a bunch of dead
code as described above. The patch adds lines because I did
- return nlmsg_end(...);
+ nlmsg_end(...);
+ return 0;
I could have preserved all the function's return values by returning
skb->len, but instead I've audited all the places calling the affected
functions and found that none cared. A few places actually compared
the return value with <= 0 in dump functionality, but that could just
be changed to < 0 with no change in behaviour, so I opted for the more
efficient version.
One instance of the error I've made numerous times now is also present
in net/phonet/pn_netlink.c in the route_dumpit() function - it didn't
check for <0 or <=0 and thus broke out of the loop every single time.
I've preserved this since it will (I think) have caused the messages to
userspace to be formatted differently with just a single message for
every SKB returned to userspace. It's possible that this isn't needed
for the tools that actually use this, but I don't even know what they
are so couldn't test that changing this behaviour would be acceptable.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
Peter Nørlund
David S. Miller
David Ahern
Alexander Duyck
Eric Dumazet
Nikola Forró
Jiri Benc
Tom Herbert
Robert Shearman
Nicolas Dichtel
Julian Anastasov
Thomas Graf
Roopa Prabhu
Masatake YAMATO
Andy Gospodarek
Eric W. Biederman
Andrew Lunn
Herbert Xu
Ian Morris
Hannes Frederic Sowa
Li Wei
Johannes Berg