| Age | Commit message (Collapse) | Author |
|---|
|
The arm dts directory has grown to 1559 boards which makes it a bit
unwieldy to maintain and use. Past attempts stalled out due to plans to
move .dts files out of the kernel tree. Doing that is no longer planned
(any time soon at least), so let's go ahead and group .dts files by
vendors. This move aligns arm with arm64 .dts file structure.
There's no change to dtbs_install as the flat structure is maintained on
install.
The naming of vendor directories is roughly in this order of preference:
- Matching original and current SoC vendor prefix/name (e.g. ti, qcom)
- Current vendor prefix/name if still actively sold (SoCs which have
been aquired) (e.g. nxp/imx)
- Existing platform name for older platforms not sold/maintained by any
company (e.g. gemini, nspire)
The whole move was scripted with the exception of MAINTAINERS and a few
makefile fixups.
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Michal Simek <michal.simek@amd.com> #Xilinx
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Neil Armstrong <neil.armstrong@linaro.org>
Acked-by: Paul Barker <paul.barker@sancloud.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Wei Xu <xuwei5@hisilicon.com> #hisilicon
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Nick Hawkins <nick.hawkins@hpe.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Peter Rosin <peda@axentia.se>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com> #broadcom
Acked-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Jisheng Zhang <jszhang@kernel.org>
Acked-by: Patrice Chotard <patrice.chotard@foss.st.com>
Acked-by: Romain Perier <romain.perier@gmail.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Acked-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Acked-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
We want to unify the pinctrl-single pin group nodes to use naming "pins".
Otherwise non-standad pin group names will add make dtbs checks errors
when the pinctrl-single yaml binding gets merged.
Cc: Conor Dooley <conor+dt@kernel.org>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The node names should be generic and DT schema expects certain pattern:
am335x-baltos-ir2110.dtb: leds: 'app', 'power', 'wlan' do not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
Acked-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20221125144118.476905-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
|
|
Switch the compatible for the am33xx_pinmux pin controller node from
pinctrl-single to pinconf-single. The only change between these two
compatibles is that PCS_HAS_PINCONF will be true. This then allows
pinconf properties to be utilized.
The purpose of this change is to allow the PocketBeagle to use:
pinctrl-single,bias-pullup
pinctrl-single,bias-pulldown
This dts already defines these properites for gpio pins in the default
pinctrl state but it has no effect unless PCS_HAS_PINCONF is set.
The bias properties can then be modified on the corresponding gpio lines
through the gpiod uapi. The mapping between the pins and gpio lines is
defined by gpio-ranges under the gpio controller nodes in am33xx-l4.dtsi
Signed-off-by: Drew Fustini <drew@pdp7.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Based on linux-gpio discussion [1], it is best practice to make the
gpio-line-names unique. Generic names like "[ethernet]" are replaced
with the name of the unique signal on the AM3358 SoC ball corresponding
to the gpio line. "[NC]" is also renamed to the standard "NC" name to
represent "not connected".
[1] https://lore.kernel.org/linux-gpio/20201216195357.GA2583366@x1/
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Drew Fustini <drew@beagleboard.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Pull ARM SoC DT updates from Arnd Bergmann:
"As usual, there are many patches addressing minor issues in existing
DTS files, such as DTC warnings, or adding support for additional
peripherals.
There are three added SoCs in existing product families:
- Amazon:
Alpine v3 is a 16-core Cortex-A72 SoC from Amazon's Annapurna Labs,
otherwise known as AL73400 or first-generation Graviton, and
following the already supported Cortex-A1`5 and Cortex-A57 based
Alpine chips. This one is added together with the official
Evaluation platform.
- Qualcomm:
The Snapdragon SDM630 platform is a family of mid-range mobile
phone chips from 2017 based on Cortex-A53 or Kryo 260 CPUs. A total
of five end-user products are added based on these, all Android
phones from Sony: Xperia 10, 10 Plus, XA2, XA2 Plus and XA2 Ultra.
- Renesas:
RZ/G2H (r8a774e1) is currently the top model in the Renesas RZ/G
family, and apparently closely related to the RZ/G2N and RZ/G2M
models we already support but has a faster GPU and additional
on-chip peripherals. It is added along with the HopeRun HiHope
RZ/G2H development board
A small number of new boards for already supported SoCs also debut:
- Allwinner sunxi:
Only one new machine, revision v1.2 of the Pine64 PinePhone
(non-Android) smartphone, containing minor changes compared to
earlier versions.
- Amlogic Meson:
WeTek Core2 is an Amlogic S912 (GXM) based Set-top-box
- Aspeed:
EthanolX is AMD's EPYC data center rerence platform, using an
ASpeed AST2600 baseboard management controller.
- Mediatek:
Lenovo IdeaPad Duet 10.1" (kukui/krane) is a new Chromebook based
on the MT8183 (Helio P60t) SoC.
- Nvidia Tegra:
ASUS Google Nexus 7 and Acer Iconia Tab A500 are two Android
tablets from around 2012 using Tegra 3 and Tegra 2, respectively.
Thanks to PostmarketOS, these can now run mainline kernels and
become useful again.
The Jetson Xavier NX Developer Kit uses a SoM and carrier board for
the Tegra194, their latest 64-bit chip based on Carmel CPU cores
and Volta graphics.
- NXP i.MX:
Five new boards based on the 32-bit i.MX6 series are added: The
MYiR MYS-6ULX single-board computer, and four different models of
industrial computers from Protonic.
- Qualcomm:
MikroTik RouterBoard 3011 is a rackmounted router based on the
32-bit IPQ8064 networking SoC
Three older phones get added, the Snapdragon 808 (msm8992) based
Xiaomi Libra (Mi 4C) and Microsoft Lumia 950, originally running
Windows Phone, and the Snapdragon 810 (msm8994) based Sony Xperia
Z5.
- Renesas:
In addition to the HiHope RZ/G2H board mentioned above, we gain
support for board versions 3.0 and 4.0 of the earlier RZ/G2M and
RZ/G2N reference boards. Beacon EmbeddedWorks adds another
SoM+Carrier development board for RZ/G2M.
- Rockchips:
Radxa Rock Pi N8 development board and the VMARC RK3288 SoM it is
based on, using the high-end 32-bit rk3288 SoC.
Notable updates to existing platforms are usually for added on-chip
peripherals, including:
- ASpeed AST2xxx (various)
- Allwinner (cpufreq, thermal, Pinephone touchscreen)
- Amlogic Meson (audio, gpu dvdfs, board updates)
- Arm Versatile
- Broadcom (board updates for switch ports, Raspberry pi clock updates)
- Hisilicon (various)
- Intel/Altera SoCFPGA (various)
- Marvell Armada 7xxx/8xxx (smmu)
- Marvell MMP (GPU on mmp2/mmp3)
- Mediatek mt8183 (USB, pericfg)
- NXP Layerscape (VPU, thermal, DSPI)
- NXP i.MX (VPU, bindings, board updates)
- Nvidia Tegra194 (GPU)
- Qualcomm (GPU, Interconnect, ...)
- Renesas R-Car (SPI, IPMMU, board updates)
- STMicroelectronics STM32 (various)
- Samsung Exynos (various)
- Socionext Uniphier (updates to serial, and pcie)
- TI K3 (serdes, usb3, audio, sd, chipid)
- TI OMAP (IPU/DSP remoteproc changes, dropping platform data)"
* tag 'arm-dt-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (605 commits)
arm64: dts: meson: odroid-n2: add jack audio output support
arm64: dts: meson: odroid-n2: enable audio loopback
ARM: dts: berlin: Align L2 cache-controller nodename with dtschema
arm64: dts: qcom: Add Microsoft Lumia 950 (Talkman) device tree
arm64: dts: qcom: Add Xiaomi Libra (Mi 4C) device tree
arm64: dts: qcom: msm8992: Add RPMCC node
arm64: dts: qcom: msm8992: Add PSCI support.
arm64: dts: qcom: msm8992: Add PMU node
arm64: dts: qcom: msm8992: Add BLSP2_UART2 and I2C nodes
arm64: dts: qcom: msm8992: Add SPMI PMIC arbiter device
arm64: dts: qcom: msm8992: Add a SCM node
arm64: dts: qcom: msm8992: Add a proper CPU map
arm64: dts: qcom: bullhead: Move UART pinctrl to SoC
arm64: dts: qcom: bullhead: Add qcom,msm-id
arm64: dts: qcom: msm8992: Fix SDHCI1
arm64: dts: qcom: msm8992: Modernize the DTS style
arm64: dts: qcom: Add support for Sony Xperia Z5 (SoMC Sumire-RoW)
arm64: dts: qcom: Move msm8994-smd-rpm contents to lg-bullhead.
arm64: dts: qcom: msm8994: Add support for SMD RPM
arm64: dts: qcom: msm8992: Add a label to rpm-requests
...
|
|
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
These pins on the PocketBeagle P1 and P2 headers are connected to AM3358
balls with gpio lines, and these pins are not used for any other
peripherals by default. These GPIO lines are unclaimed and could be used
by userspace program through the gpiod ABI.
This patch adds a "default" state in the am33xx_pinmux node and sets the
mux for those pins to gpio (mode 7) and input enable.
The "pinctrl-single,bias-pullup" and "pinctrl-single,bias-pulldown"
pinconf properties are also set for each pin per the ball reset state in
section 4.2 of the datasheet [0].
This is the AM335x pin control register format in Table 9-60 [1]:
bit attribute value
----------------------------------
31-7 reserved 0 on reset
6 slew { 0: fast, 1: slow }
5 rx_active { 0: rx disable, 1: rx enabled }
4 pu_typesel { 0: pulldown select, 1: pullup select }
3 puden { 0: pud enable, 1: disabled }
2 mode 3 bits to selec mode 0 to 7
1 mode
0 mode
The values for the bias pinconf properties are derived as follows:
pinctrl-single,bias-pullup = <[input] [enabled] [disable] [mask]>;
pinctrl-single,bias-pullup = < 0x10 0x10 0x10 0x18 >;
2^5 2^4 2^3 2^2 2^1 2^0 |
0x20 0x10 0x08 0x04 0x02 0x01 |
--------------------------------------------------|
input x 1 0 x x x | 0x10
enabled x 1 0 x x x | 0x10
disabled x 0 0 x x x | 0x00
mask x 1 1 x x x | 0x18
pinctrl-single,bias-pulldown = <[input] [enabled] [disable] [mask]>;
pinctrl-single,bias-pulldown = < 0x0 0x0 0x10 0x18 >;
2^5 2^4 2^3 2^2 2^1 2^0 |
0x20 0x10 0x08 0x04 0x02 0x01 |
--------------------------------------------------|
input x 0 0 x x x | 0x00
enabled x 0 0 x x x | 0x00
disabled x 1 0 x x x | 0x10
mask x 1 1 x x x | 0x18
[0] http://www.ti.com/lit/ds/symlink/am3358.pdf
[1] https://www.ti.com/lit/ug/spruh73q/spruh73q.pdf
Signed-off-by: Drew Fustini <drew@beagleboard.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The BeagleBoard.org PocketBeagle has P1 and P2 headers [0] which expose
many of the TI AM3358 SoC balls to stacking expansion boards called
"capes", or to other external connections like jumper wires connected
to a breadboard.
Note: the AM3358 die is actually embedded inside of the OSD335x-SM
System-in-Package (SiP) [1] but that is irrelevant to the gpio driver.
Many of the P1 and P2 header pins can muxed to a GPIO line. The
gpio-line-names describe which P1 or P2 pin that line goes to and the
default mux for that P1 or P2 pin if it is not GPIO.
Some GPIO lines are named "[NC]" as the corresponding balls are not
routed to anything on the PCB.
The goal for these names is to make it easier for a user viewing the
output of gpioinfo to determine which P1 or P2 pin is connected to a
GPIO line. The output of gpioinfo on a PocketBeagle would be:
gpiochip0 - 32 lines:
line 0: "[NC]" unused input active-high
line 1: "[NC]" unused input active-high
line 2: "P1.08 [SPI0_CLK]" unused input active-high
line 3: "P1.10 [SPI0_MISO]" unused input active-high
line 4: "P1.12 [SPI0_MOSI]" unused input active-high
line 5: "P1.06 [SPI0_CS]" unused input active-high
line 6: "[MMC0_CD]" "cd" input active-low [used]
line 7: "P2.29 [SPI1_CLK]" unused input active-high
line 8: "[SYSBOOT]" unused input active-high
line 9: "[SYSBOOT]" unused input active-high
line 10: "[SYSBOOT]" unused input active-high
line 11: "[SYSBOOT]" unused input active-high
line 12: "P1.26 [I2C2_SDA]" unused input active-high
line 13: "P1.28 [I2C2_SCL]" unused input active-high
line 14: "P2.11 [I2C1_SDA]" unused input active-high
line 15: "P2.09 [I2C1_SCL]" unused input active-high
line 16: "[NC]" unused input active-high
line 17: "[NC]" unused input active-high
line 18: "[NC]" unused input active-high
line 19: "P2.31 [SPI1_CS]" unused input active-high
line 20: "P1.20 [PRU0.16]" unused input active-high
line 21: "[NC]" unused input active-high
line 22: "[NC]" unused input active-high
line 23: "P2.03" unused input active-high
line 24: "[NC]" unused input active-high
line 25: "[NC]" unused input active-high
line 26: "P1.34" unused input active-high
line 27: "P2.19" unused input active-high
line 28: "[NC]" unused input active-high
line 29: "[NC]" unused input active-high
line 30: "P2.05 [UART4_RX]" unused input active-high
line 31: "P2.07 [UART4_TX]" unused input active-high
gpiochip1 - 32 lines:
line 0: "[NC]" unused input active-high
line 1: "[NC]" unused input active-high
line 2: "[NC]" unused input active-high
line 3: "[NC]" unused input active-high
line 4: "[NC]" unused input active-high
line 5: "[NC]" unused input active-high
line 6: "[NC]" unused input active-high
line 7: "[NC]" unused input active-high
line 8: "[NC]" unused input active-high
line 9: "P2.25 [SPI1_MOSI]" unused input active-high
line 10: "P1.32 [UART0_RX]" unused input active-high
line 11: "P1.30 [UART0_TX]" unused input active-high
line 12: "P2.24" unused input active-high
line 13: "P2.33" unused input active-high
line 14: "P2.22" unused input active-high
line 15: "P2.18" unused input active-high
line 16: "[NC]" unused input active-high
line 17: "[NC]" unused input active-high
line 18: "P2.01 [PWM1A]" unused input active-high
line 19: "[NC]" unused input active-high
line 20: "P2.10" unused input active-high
line 21: "[USR LED 0]" "beaglebone:green:usr0" output active-high [used]
line 22: "[USR LED 1]" "beaglebone:green:usr1" output active-high [used]
line 23: "[USR LED 2]" "beaglebone:green:usr2" output active-high [used]
line 24: "[USR LED 3]" "beaglebone:green:usr3" output active-high [used]
line 25: "P2.06" unused input active-high
line 26: "P2.04" unused input active-high
line 27: "P2.02" unused input active-high
line 28: "P2.08" unused input active-high
line 29: "[NC]" unused input active-high
line 30: "[NC]" unused input active-high
line 31: "[NC]" unused input active-high
gpiochip2 - 32 lines:
line 0: "P2.20" unused input active-high
line 1: "P2.17" unused input active-high
line 2: "[NC]" unused input active-high
line 3: "[NC]" unused input active-high
line 4: "[NC]" unused input active-high
line 5: "[EEPROM_WP]" unused input active-high
line 6: "[SYSBOOT]" unused input active-high
line 7: "[SYSBOOT]" unused input active-high
line 8: "[SYSBOOT]" unused input active-high
line 9: "[SYSBOOT]" unused input active-high
line 10: "[SYSBOOT]" unused input active-high
line 11: "[SYSBOOT]" unused input active-high
line 12: "[SYSBOOT]" unused input active-high
line 13: "[SYSBOOT]" unused input active-high
line 14: "[SYSBOOT]" unused input active-high
line 15: "[SYSBOOT]" unused input active-high
line 16: "[SYSBOOT]" unused input active-high
line 17: "[SYSBOOT]" unused input active-high
line 18: "[NC]" unused input active-high
line 19: "[NC]" unused input active-high
line 20: "[NC]" unused input active-high
line 21: "[NC]" unused input active-high
line 22: "P2.35 [AIN5]" unused input active-high
line 23: "P1.02 [AIN6]" unused input active-high
line 24: "P1.35 [PRU1.10]" unused input active-high
line 25: "P1.04 [PRU1.11]" unused input active-high
line 26: "[MMC0_DAT3]" unused input active-high
line 27: "[MMC0_DAT2]" unused input active-high
line 28: "[MMC0_DAT1]" unused input active-high
line 29: "[MMC0_DAT0]" unused input active-high
line 30: "[MMC0_CLK]" unused input active-high
line 31: "[MMC0_CMD]" unused input active-high
gpiochip3 - 32 lines:
line 0: "[NC]" unused input active-high
line 1: "[NC]" unused input active-high
line 2: "[NC]" unused input active-high
line 3: "[NC]" unused input active-high
line 4: "[NC]" unused input active-high
line 5: "[I2C0_SDA]" unused input active-high
line 6: "[I2C0_SCL]" unused input active-high
line 7: "[JTAG]" unused input active-high
line 8: "[JTAG]" unused input active-high
line 9: "[NC]" unused input active-high
line 10: "[NC]" unused input active-high
line 11: "[NC]" unused input active-high
line 12: "[NC]" unused input active-high
line 13: "P1.03 [USB1]" unused input active-high
line 14: "P1.36 [PWM0A]" unused input active-high
line 15: "P1.33 [PRU0.1]" unused input active-high
line 16: "P2.32 [PRU0.2]" unused input active-high
line 17: "P2.30 [PRU0.3]" unused input active-high
line 18: "P1.31 [PRU0.4]" unused input active-high
line 19: "P2.34 [PRU0.5]" unused input active-high
line 20: "P2.28 [PRU0.6]" unused input active-high
line 21: "P1.29 [PRU0.7]" unused input active-high
line 22: "[NC]" unused input active-high
line 23: "[NC]" unused input active-high
line 24: "[NC]" unused input active-high
line 25: "[NC]" unused input active-high
line 26: "[NC]" unused input active-high
line 27: "[NC]" unused input active-high
line 28: "[NC]" unused input active-high
line 29: "[NC]" unused input active-high
line 30: "[NC]" unused input active-high
line 31: "[NC]" unused input active-high
[0] https://github.com/beagleboard/pocketbeagle/wiki/System-Reference-Manual#71_Expansion_Header_Connectors
[1] https://octavosystems.com/app_notes/osd335x-family-pin-assignments/
Reviewed-by: Jason Kridner <jason@beagleboard.org>
Reviewed-by: Robert Nelson <robertcnelson@gmail.com>
Signed-off-by: Drew Fustini <drew@beagleboard.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
AM3358 pin mcasp0_aclkr (ZCZ ball B13) [0] is routed to P1.31 header [1]
Mode 4 of this pin is mmc0_sdwp (SD Write Protect). A signal connected
to P1.31 may accidentally trigger mmc0 write protection. To avoid this
situation, do not put mcasp0_aclkr in mode 4 (mmc0_sdwp) by default.
[0] http://www.ti.com/lit/ds/symlink/am3358.pdf
[1] https://github.com/beagleboard/pocketbeagle/wiki/System-Reference-Manual#531_Expansion_Headers
Fixes: 047905376a16 (ARM: dts: Add am335x-pocketbeagle)
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
Signed-off-by: Drew Fustini <drew@beagleboard.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The default is enabled, and there should be no need to reconfigure
the status for SoC internal devices in the board specific files.
Only the USB PHY used needs to be configured in the board specific
files.
Cc: Bin Liu <b-liu@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The defines are taken from dt-bindings/pinctrl/am33xx.h
Signed-off-by: Christina Quast <cquast@hanoverdisplays.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
PocketBeagle is an ultra-tiny-yet-complete open-source USB-key-fob computer.
This board family can be indentified by the A335PBGL in the at24 eeprom:
A2: [aa 55 33 ee 41 33 33 35 50 42 47 4c 30 30 41 32 |.U3.A335PBGL00A2|]
http://beagleboard.org/pocket
https://github.com/beagleboard/pocketbeagle
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
CC: Tony Lindgren <tony@atomide.com>
CC: Jason Kridner <jkridner@beagleboard.org>
CC: Drew Fustini <drew@beagleboard.org>
CC: Peter Robinson <pbrobinson@redhat.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
Rob Herring
Tony Lindgren
Krzysztof Kozlowski
Drew Fustini
Drew Fustini
Linus Torvalds
Alexander A. Klimov
Christina Quast
Robert Nelson