diff options
Diffstat (limited to 'drivers/tty/serial/8250')
| -rw-r--r-- | drivers/tty/serial/8250/8250_em.c | 2 | ||||
| -rw-r--r-- | drivers/tty/serial/8250/8250_exar.c | 24 | ||||
| -rw-r--r-- | drivers/tty/serial/8250/8250_fintek.c | 2 | ||||
| -rw-r--r-- | drivers/tty/serial/8250/8250_pci.c | 2 | ||||
| -rw-r--r-- | drivers/tty/serial/8250/8250_port.c | 11 | ||||
| -rw-r--r-- | drivers/tty/serial/8250/8250_uniphier.c | 6 |
6 files changed, 34 insertions, 13 deletions
diff --git a/drivers/tty/serial/8250/8250_em.c b/drivers/tty/serial/8250/8250_em.c index db88dee3a399..f8e99995eee9 100644 --- a/drivers/tty/serial/8250/8250_em.c +++ b/drivers/tty/serial/8250/8250_em.c @@ -39,7 +39,7 @@ static void serial8250_em_serial_out(struct uart_port *p, int offset, int value) break; case UART_IER: /* IER @ 0x04 */ value &= 0x0f; /* only 4 valid bits - not Xscale */ - /* fall-through */ + fallthrough; case UART_DLL_EM: /* DLL @ 0x24 (+9) */ case UART_DLM_EM: /* DLM @ 0x28 (+9) */ writel(value, p->membase + (offset << 2)); diff --git a/drivers/tty/serial/8250/8250_exar.c b/drivers/tty/serial/8250/8250_exar.c index 04b9af7ed941..2d0e7c7e408d 100644 --- a/drivers/tty/serial/8250/8250_exar.c +++ b/drivers/tty/serial/8250/8250_exar.c @@ -744,6 +744,24 @@ static const struct exar8250_board pbn_exar_XR17V35x = { .exit = pci_xr17v35x_exit, }; +static const struct exar8250_board pbn_fastcom35x_2 = { + .num_ports = 2, + .setup = pci_xr17v35x_setup, + .exit = pci_xr17v35x_exit, +}; + +static const struct exar8250_board pbn_fastcom35x_4 = { + .num_ports = 4, + .setup = pci_xr17v35x_setup, + .exit = pci_xr17v35x_exit, +}; + +static const struct exar8250_board pbn_fastcom35x_8 = { + .num_ports = 8, + .setup = pci_xr17v35x_setup, + .exit = pci_xr17v35x_exit, +}; + static const struct exar8250_board pbn_exar_XR17V4358 = { .num_ports = 12, .setup = pci_xr17v35x_setup, @@ -811,9 +829,9 @@ static const struct pci_device_id exar_pci_tbl[] = { EXAR_DEVICE(EXAR, XR17V358, pbn_exar_XR17V35x), EXAR_DEVICE(EXAR, XR17V4358, pbn_exar_XR17V4358), EXAR_DEVICE(EXAR, XR17V8358, pbn_exar_XR17V8358), - EXAR_DEVICE(COMMTECH, 4222PCIE, pbn_exar_XR17V35x), - EXAR_DEVICE(COMMTECH, 4224PCIE, pbn_exar_XR17V35x), - EXAR_DEVICE(COMMTECH, 4228PCIE, pbn_exar_XR17V35x), + EXAR_DEVICE(COMMTECH, 4222PCIE, pbn_fastcom35x_2), + EXAR_DEVICE(COMMTECH, 4224PCIE, pbn_fastcom35x_4), + EXAR_DEVICE(COMMTECH, 4228PCIE, pbn_fastcom35x_8), EXAR_DEVICE(COMMTECH, 4222PCI335, pbn_fastcom335_2), EXAR_DEVICE(COMMTECH, 4224PCI335, pbn_fastcom335_4), diff --git a/drivers/tty/serial/8250/8250_fintek.c b/drivers/tty/serial/8250/8250_fintek.c index d1d253c4b518..31c9e83ea3cb 100644 --- a/drivers/tty/serial/8250/8250_fintek.c +++ b/drivers/tty/serial/8250/8250_fintek.c @@ -255,7 +255,7 @@ static void fintek_8250_set_irq_mode(struct fintek_8250 *pdata, bool is_level) case CHIP_ID_F81866: sio_write_mask_reg(pdata, F81866_FIFO_CTRL, F81866_IRQ_MODE1, 0); - /* fall through */ + fallthrough; case CHIP_ID_F81865: sio_write_mask_reg(pdata, F81866_IRQ_MODE, F81866_IRQ_SHARE, F81866_IRQ_SHARE); diff --git a/drivers/tty/serial/8250/8250_pci.c b/drivers/tty/serial/8250/8250_pci.c index 1a74d511b02a..3eb2d485eaeb 100644 --- a/drivers/tty/serial/8250/8250_pci.c +++ b/drivers/tty/serial/8250/8250_pci.c @@ -631,7 +631,7 @@ pci_timedia_setup(struct serial_private *priv, break; case 3: offset = board->uart_offset; - /* FALLTHROUGH */ + fallthrough; case 4: /* BAR 2 */ case 5: /* BAR 3 */ case 6: /* BAR 4 */ diff --git a/drivers/tty/serial/8250/8250_port.c b/drivers/tty/serial/8250/8250_port.c index 09475695effd..c71d647eb87a 100644 --- a/drivers/tty/serial/8250/8250_port.c +++ b/drivers/tty/serial/8250/8250_port.c @@ -1872,7 +1872,7 @@ static bool handle_rx_dma(struct uart_8250_port *up, unsigned int iir) switch (iir & 0x3f) { case UART_IIR_RX_TIMEOUT: serial8250_rx_dma_flush(up); - /* fall-through */ + fallthrough; case UART_IIR_RLSI: return true; } @@ -2275,6 +2275,10 @@ int serial8250_do_startup(struct uart_port *port) if (port->irq && !(up->port.flags & UPF_NO_THRE_TEST)) { unsigned char iir1; + + if (port->irqflags & IRQF_SHARED) + disable_irq_nosync(port->irq); + /* * Test for UARTs that do not reassert THRE when the * transmitter is idle and the interrupt has already @@ -2284,8 +2288,6 @@ int serial8250_do_startup(struct uart_port *port) * allow register changes to become visible. */ spin_lock_irqsave(&port->lock, flags); - if (up->port.irqflags & IRQF_SHARED) - disable_irq_nosync(port->irq); wait_for_xmitr(up, UART_LSR_THRE); serial_port_out_sync(port, UART_IER, UART_IER_THRI); @@ -2297,9 +2299,10 @@ int serial8250_do_startup(struct uart_port *port) iir = serial_port_in(port, UART_IIR); serial_port_out(port, UART_IER, 0); + spin_unlock_irqrestore(&port->lock, flags); + if (port->irqflags & IRQF_SHARED) enable_irq(port->irq); - spin_unlock_irqrestore(&port->lock, flags); /* * If the interrupt is not reasserted, or we otherwise diff --git a/drivers/tty/serial/8250/8250_uniphier.c b/drivers/tty/serial/8250/8250_uniphier.c index e0b73a5402db..a2978abab0db 100644 --- a/drivers/tty/serial/8250/8250_uniphier.c +++ b/drivers/tty/serial/8250/8250_uniphier.c @@ -75,7 +75,7 @@ static unsigned int uniphier_serial_in(struct uart_port *p, int offset) break; case UART_LCR: valshift = 8; - /* fall through */ + fallthrough; case UART_MCR: offset = UNIPHIER_UART_LCR_MCR; break; @@ -101,7 +101,7 @@ static void uniphier_serial_out(struct uart_port *p, int offset, int value) case UART_SCR: /* No SCR for this hardware. Use CHAR as a scratch register */ valshift = 8; - /* fall through */ + fallthrough; case UART_FCR: offset = UNIPHIER_UART_CHAR_FCR; break; @@ -109,7 +109,7 @@ static void uniphier_serial_out(struct uart_port *p, int offset, int value) valshift = 8; /* Divisor latch access bit does not exist. */ value &= ~UART_LCR_DLAB; - /* fall through */ + fallthrough; case UART_MCR: offset = UNIPHIER_UART_LCR_MCR; break; |