diff options
Diffstat (limited to 'arch/arm/boot/dts/imx28-cfa10058.dts')
| -rw-r--r-- | arch/arm/boot/dts/imx28-cfa10058.dts | 186 |
1 files changed, 88 insertions, 98 deletions
diff --git a/arch/arm/boot/dts/imx28-cfa10058.dts b/arch/arm/boot/dts/imx28-cfa10058.dts index 4465fd86785a..931c4d089b26 100644 --- a/arch/arm/boot/dts/imx28-cfa10058.dts +++ b/arch/arm/boot/dts/imx28-cfa10058.dts @@ -14,93 +14,6 @@ model = "Crystalfontz CFA-10058 Board"; compatible = "crystalfontz,cfa10058", "crystalfontz,cfa10036", "fsl,imx28"; - apb@80000000 { - apbh@80000000 { - pinctrl@80018000 { - usb_pins_cfa10058: usb-10058@0 { - reg = <0>; - fsl,pinmux-ids = < - MX28_PAD_GPMI_D07__GPIO_0_7 - >; - fsl,drive-strength = <MXS_DRIVE_4mA>; - fsl,voltage = <MXS_VOLTAGE_HIGH>; - fsl,pull-up = <MXS_PULL_DISABLE>; - }; - - lcdif_pins_cfa10058: lcdif-10058@0 { - reg = <0>; - fsl,pinmux-ids = < - MX28_PAD_LCD_RD_E__LCD_VSYNC - MX28_PAD_LCD_WR_RWN__LCD_HSYNC - MX28_PAD_LCD_RS__LCD_DOTCLK - MX28_PAD_LCD_CS__LCD_ENABLE - >; - fsl,drive-strength = <MXS_DRIVE_4mA>; - fsl,voltage = <MXS_VOLTAGE_HIGH>; - fsl,pull-up = <MXS_PULL_DISABLE>; - }; - }; - - lcdif@80030000 { - pinctrl-names = "default"; - pinctrl-0 = <&lcdif_24bit_pins_a - &lcdif_pins_cfa10058>; - display = <&display0>; - status = "okay"; - - display0: display0 { - bits-per-pixel = <32>; - bus-width = <24>; - - display-timings { - native-mode = <&timing0>; - timing0: timing0 { - clock-frequency = <30000000>; - hactive = <800>; - vactive = <480>; - hback-porch = <40>; - hfront-porch = <40>; - vback-porch = <13>; - vfront-porch = <29>; - hsync-len = <8>; - vsync-len = <8>; - hsync-active = <0>; - vsync-active = <0>; - de-active = <1>; - pixelclk-active = <1>; - }; - }; - }; - }; - }; - - apbx@80040000 { - lradc@80050000 { - fsl,lradc-touchscreen-wires = <4>; - status = "okay"; - }; - - pwm: pwm@80064000 { - pinctrl-names = "default"; - pinctrl-0 = <&pwm3_pins_b>; - status = "okay"; - }; - - usbphy1: usbphy@8007e000 { - status = "okay"; - }; - }; - }; - - ahb@80080000 { - usb1: usb@80090000 { - vbus-supply = <®_usb1_vbus>; - pinctrl-0 = <&usb1_pins_a>; - pinctrl-names = "default"; - status = "okay"; - }; - }; - regulators { compatible = "simple-bus"; #address-cells = <1>; @@ -118,17 +31,6 @@ }; }; - ahb@80080000 { - mac0: ethernet@800f0000 { - phy-mode = "rmii"; - pinctrl-names = "default"; - pinctrl-0 = <&mac0_pins_a>; - phy-reset-gpios = <&gpio2 21 GPIO_ACTIVE_LOW>; - phy-reset-duration = <100>; - status = "okay"; - }; - }; - backlight { compatible = "pwm-backlight"; pwms = <&pwm 3 5000000>; @@ -136,3 +38,91 @@ default-brightness-level = <6>; }; }; + +&lcdif { + pinctrl-names = "default"; + pinctrl-0 = <&lcdif_24bit_pins_a + &lcdif_pins_cfa10058>; + display = <&display0>; + status = "okay"; + + display0: display0 { + bits-per-pixel = <32>; + bus-width = <24>; + + display-timings { + native-mode = <&timing0>; + timing0: timing0 { + clock-frequency = <30000000>; + hactive = <800>; + vactive = <480>; + hback-porch = <40>; + hfront-porch = <40>; + vback-porch = <13>; + vfront-porch = <29>; + hsync-len = <8>; + vsync-len = <8>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <1>; + }; + }; + }; +}; + +&lradc { + fsl,lradc-touchscreen-wires = <4>; + status = "okay"; +}; + +&mac0 { + phy-mode = "rmii"; + pinctrl-names = "default"; + pinctrl-0 = <&mac0_pins_a>; + phy-reset-gpios = <&gpio2 21 GPIO_ACTIVE_LOW>; + phy-reset-duration = <100>; + status = "okay"; +}; + +&pinctrl { + usb_pins_cfa10058: usb-10058@0 { + reg = <0>; + fsl,pinmux-ids = < + MX28_PAD_GPMI_D07__GPIO_0_7 + >; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; + }; + + lcdif_pins_cfa10058: lcdif-10058@0 { + reg = <0>; + fsl,pinmux-ids = < + MX28_PAD_LCD_RD_E__LCD_VSYNC + MX28_PAD_LCD_WR_RWN__LCD_HSYNC + MX28_PAD_LCD_RS__LCD_DOTCLK + MX28_PAD_LCD_CS__LCD_ENABLE + >; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; + }; +}; + +&pwm { + pinctrl-names = "default"; + pinctrl-0 = <&pwm3_pins_b>; + status = "okay"; +}; + +&usb1 { + vbus-supply = <®_usb1_vbus>; + pinctrl-0 = <&usb1_pins_a>; + pinctrl-names = "default"; + status = "okay"; +}; + +&usbphy1 { + status = "okay"; +}; |