diff options
Diffstat (limited to 'Documentation/hwmon/ina209')
-rw-r--r-- | Documentation/hwmon/ina209 | 93 |
1 files changed, 0 insertions, 93 deletions
diff --git a/Documentation/hwmon/ina209 b/Documentation/hwmon/ina209 deleted file mode 100644 index 672501de4509..000000000000 --- a/Documentation/hwmon/ina209 +++ /dev/null @@ -1,93 +0,0 @@ -Kernel driver ina209 -===================== - -Supported chips: - * Burr-Brown / Texas Instruments INA209 - Prefix: 'ina209' - Addresses scanned: - - Datasheet: - http://www.ti.com/lit/gpn/ina209 - -Author: Paul Hays <Paul.Hays@cattail.ca> -Author: Ira W. Snyder <iws@ovro.caltech.edu> -Author: Guenter Roeck <linux@roeck-us.net> - - -Description ------------ - -The TI / Burr-Brown INA209 monitors voltage, current, and power on the high side -of a D.C. power supply. It can perform measurements and calculations in the -background to supply readings at any time. It includes a programmable -calibration multiplier to scale the displayed current and power values. - - -Sysfs entries -------------- - -The INA209 chip is highly configurable both via hardwiring and via -the I2C bus. See the datasheet for details. - -This tries to expose most monitoring features of the hardware via -sysfs. It does not support every feature of this chip. - - -in0_input shunt voltage (mV) -in0_input_highest shunt voltage historical maximum reading (mV) -in0_input_lowest shunt voltage historical minimum reading (mV) -in0_reset_history reset shunt voltage history -in0_max shunt voltage max alarm limit (mV) -in0_min shunt voltage min alarm limit (mV) -in0_crit_max shunt voltage crit max alarm limit (mV) -in0_crit_min shunt voltage crit min alarm limit (mV) -in0_max_alarm shunt voltage max alarm limit exceeded -in0_min_alarm shunt voltage min alarm limit exceeded -in0_crit_max_alarm shunt voltage crit max alarm limit exceeded -in0_crit_min_alarm shunt voltage crit min alarm limit exceeded - -in1_input bus voltage (mV) -in1_input_highest bus voltage historical maximum reading (mV) -in1_input_lowest bus voltage historical minimum reading (mV) -in1_reset_history reset bus voltage history -in1_max bus voltage max alarm limit (mV) -in1_min bus voltage min alarm limit (mV) -in1_crit_max bus voltage crit max alarm limit (mV) -in1_crit_min bus voltage crit min alarm limit (mV) -in1_max_alarm bus voltage max alarm limit exceeded -in1_min_alarm bus voltage min alarm limit exceeded -in1_crit_max_alarm bus voltage crit max alarm limit exceeded -in1_crit_min_alarm bus voltage crit min alarm limit exceeded - -power1_input power measurement (uW) -power1_input_highest power historical maximum reading (uW) -power1_reset_history reset power history -power1_max power max alarm limit (uW) -power1_crit power crit alarm limit (uW) -power1_max_alarm power max alarm limit exceeded -power1_crit_alarm power crit alarm limit exceeded - -curr1_input current measurement (mA) - -update_interval data conversion time; affects number of samples used - to average results for shunt and bus voltages. - -General Remarks ---------------- - -The power and current registers in this chip require that the calibration -register is programmed correctly before they are used. Normally this is expected -to be done in the BIOS. In the absence of BIOS programming, the shunt resistor -voltage can be provided using platform data. The driver uses platform data from -the ina2xx driver for this purpose. If calibration register data is not provided -via platform data, the driver checks if the calibration register has been -programmed (ie has a value not equal to zero). If so, this value is retained. -Otherwise, a default value reflecting a shunt resistor value of 10 mOhm is -programmed into the calibration register. - - -Output Pins ------------ - -Output pin programming is a board feature which depends on the BIOS. It is -outside the scope of a hardware monitoring driver to enable or disable output -pins. |