diff options
Diffstat (limited to 'Documentation/devicetree/bindings/sound')
32 files changed, 962 insertions, 182 deletions
diff --git a/Documentation/devicetree/bindings/sound/adi,adau1977.txt b/Documentation/devicetree/bindings/sound/adi,adau1977.txt new file mode 100644 index 000000000000..e79aeef73f28 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/adi,adau1977.txt @@ -0,0 +1,54 @@ +Analog Devices ADAU1977/ADAU1978/ADAU1979 + +Datasheets: +http://www.analog.com/media/en/technical-documentation/data-sheets/ADAU1977.pdf +http://www.analog.com/media/en/technical-documentation/data-sheets/ADAU1978.pdf +http://www.analog.com/media/en/technical-documentation/data-sheets/ADAU1979.pdf + +This driver supports both the I2C and SPI bus. + +Required properties: + - compatible: Should contain one of the following: + "adi,adau1977" + "adi,adau1978" + "adi,adau1979" + + - AVDD-supply: analog power supply for the device, please consult + Documentation/devicetree/bindings/regulator/regulator.txt + +Optional properties: + - reset-gpio: the reset pin for the chip, for more details consult + Documentation/devicetree/bindings/gpio/gpio.txt + + - DVDD-supply: supply voltage for the digital core, please consult + Documentation/devicetree/bindings/regulator/regulator.txt + +For required properties on SPI, please consult +Documentation/devicetree/bindings/spi/spi-bus.txt + +Required properties on I2C: + + - reg: The i2c address. Value depends on the state of ADDR0 + and ADDR1, as wired in hardware. + +Examples: + + adau1977_spi: adau1977@0 { + compatible = "adi,adau1977"; + spi-max-frequency = <600000>; + + AVDD-supply = <®ulator>; + DVDD-supply = <®ulator_digital>; + + reset_gpio = <&gpio 10 GPIO_ACTIVE_LOW>; + }; + + adau1977_i2c: adau1977@11 { + compatible = "adi,adau1977"; + reg = <0x11>; + + AVDD-supply = <®ulator>; + DVDD-supply = <®ulator_digital>; + + reset_gpio = <&gpio 10 GPIO_ACTIVE_LOW>; + }; diff --git a/Documentation/devicetree/bindings/sound/ak4104.txt b/Documentation/devicetree/bindings/sound/ak4104.txt index deca5e18f304..ae5f7f057dc3 100644 --- a/Documentation/devicetree/bindings/sound/ak4104.txt +++ b/Documentation/devicetree/bindings/sound/ak4104.txt @@ -12,8 +12,8 @@ Required properties: Optional properties: - - reset-gpio : a GPIO spec for the reset pin. If specified, it will be - deasserted before communication to the device starts. + - reset-gpios : a GPIO spec for the reset pin. If specified, it will be + deasserted before communication to the device starts. Example: diff --git a/Documentation/devicetree/bindings/sound/ak4118.txt b/Documentation/devicetree/bindings/sound/ak4118.txt new file mode 100644 index 000000000000..6e11a2f7404c --- /dev/null +++ b/Documentation/devicetree/bindings/sound/ak4118.txt @@ -0,0 +1,22 @@ +AK4118 S/PDIF transceiver + +This device supports I2C mode. + +Required properties: + +- compatible : "asahi-kasei,ak4118" +- reg : The I2C address of the device for I2C +- reset-gpios: A GPIO specifier for the reset pin +- irq-gpios: A GPIO specifier for the IRQ pin + +Example: + +&i2c { + ak4118: ak4118@13 { + #sound-dai-cells = <0>; + compatible = "asahi-kasei,ak4118"; + reg = <0x13>; + reset-gpios = <&gpio 0 GPIO_ACTIVE_LOW> + irq-gpios = <&gpio 1 GPIO_ACTIVE_HIGH>; + }; +}; diff --git a/Documentation/devicetree/bindings/sound/amlogic,axg-pdm.txt b/Documentation/devicetree/bindings/sound/amlogic,axg-pdm.txt new file mode 100644 index 000000000000..5672d0bc5b16 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/amlogic,axg-pdm.txt @@ -0,0 +1,24 @@ +* Amlogic Audio PDM input + +Required properties: +- compatible: 'amlogic,axg-pdm' +- reg: physical base address of the controller and length of memory + mapped region. +- clocks: list of clock phandle, one for each entry clock-names. +- clock-names: should contain the following: + * "pclk" : peripheral clock. + * "dclk" : pdm digital clock + * "sysclk" : dsp system clock +- #sound-dai-cells: must be 0. + +Example of PDM on the A113 SoC: + +pdm: audio-controller@ff632000 { + compatible = "amlogic,axg-pdm"; + reg = <0x0 0xff632000 0x0 0x34>; + #sound-dai-cells = <0>; + clocks = <&clkc_audio AUD_CLKID_PDM>, + <&clkc_audio AUD_CLKID_PDM_DCLK>, + <&clkc_audio AUD_CLKID_PDM_SYSCLK>; + clock-names = "pclk", "dclk", "sysclk"; +}; diff --git a/Documentation/devicetree/bindings/sound/amlogic,axg-spdifin.txt b/Documentation/devicetree/bindings/sound/amlogic,axg-spdifin.txt new file mode 100644 index 000000000000..2e6cb7d9b202 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/amlogic,axg-spdifin.txt @@ -0,0 +1,22 @@ +* Amlogic Audio SPDIF Input + +Required properties: +- compatible: 'amlogic,axg-spdifin' +- interrupts: interrupt specifier for the spdif input. +- clocks: list of clock phandle, one for each entry clock-names. +- clock-names: should contain the following: + * "pclk" : peripheral clock. + * "refclk" : spdif input reference clock +- #sound-dai-cells: must be 0. + +Example on the A113 SoC: + +spdifin: audio-controller@400 { + compatible = "amlogic,axg-spdifin"; + reg = <0x0 0x400 0x0 0x30>; + #sound-dai-cells = <0>; + interrupts = <GIC_SPI 87 IRQ_TYPE_EDGE_RISING>; + clocks = <&clkc_audio AUD_CLKID_SPDIFIN>, + <&clkc_audio AUD_CLKID_SPDIFIN_CLK>; + clock-names = "pclk", "refclk"; +}; diff --git a/Documentation/devicetree/bindings/sound/audio-graph-card.txt b/Documentation/devicetree/bindings/sound/audio-graph-card.txt index 7e63e53a901c..269682619a70 100644 --- a/Documentation/devicetree/bindings/sound/audio-graph-card.txt +++ b/Documentation/devicetree/bindings/sound/audio-graph-card.txt @@ -32,7 +32,9 @@ Required properties: Optional properties: - pa-gpios: GPIO used to control external amplifier. +----------------------- Example: Single DAI case +----------------------- sound_card { compatible = "audio-graph-card"; @@ -61,7 +63,9 @@ Example: Single DAI case }; }; +----------------------- Example: Multi DAI case +----------------------- sound-card { compatible = "audio-graph-card"; @@ -130,3 +134,204 @@ Example: Multi DAI case }; }; + +----------------------- +Example: Sampling Rate Conversion +----------------------- + + sound_card { + compatible = "audio-graph-card"; + + label = "sound-card"; + prefix = "codec"; + routing = "codec Playback", "DAI0 Playback", + "DAI0 Capture", "codec Capture"; + convert-rate = <48000>; + + dais = <&cpu_port>; + }; + + audio-codec { + ... + port { + codec_endpoint: endpoint { + remote-endpoint = <&cpu_endpoint>; + }; + }; + }; + + dai-controller { + ... + cpu_port: port { + cpu_endpoint: endpoint { + remote-endpoint = <&codec_endpoint>; + + dai-format = "left_j"; + ... + }; + }; + }; + +----------------------- +Example: 2 CPU 1 Codec (Mixing) +----------------------- + + sound_card { + compatible = "audio-graph-card"; + + label = "sound-card"; + routing = "codec Playback", "DAI0 Playback", + "codec Playback", "DAI1 Playback", + "DAI0 Capture", "codec Capture"; + + dais = <&cpu_port>; + }; + + audio-codec { + ... + + audio-graph-card,prefix = "codec"; + audio-graph-card,convert-rate = <48000>; + port { + reg = <0>; + codec_endpoint0: endpoint@0 { + remote-endpoint = <&cpu_endpoint0>; + }; + codec_endpoint1: endpoint@1 { + remote-endpoint = <&cpu_endpoint1>; + }; + }; + }; + + dai-controller { + ... + cpu_port: port { + cpu_endpoint0: endpoint@0 { + remote-endpoint = <&codec_endpoint0>; + + dai-format = "left_j"; + ... + }; + cpu_endpoint1: endpoint@1 { + remote-endpoint = <&codec_endpoint1>; + + dai-format = "left_j"; + ... + }; + }; + }; + +----------------------- +Example: Multi DAI with DPCM +----------------------- + + CPU0 ------ ak4613 + CPU1 ------ HDMI + CPU2 ------ PCM3168A-p /* DPCM 1ch/2ch */ + CPU3 --/ /* DPCM 3ch/4ch */ + CPU4 --/ /* DPCM 5ch/6ch */ + CPU5 --/ /* DPCM 7ch/8ch */ + CPU6 ------ PCM3168A-c + + sound_card: sound { + compatible = "audio-graph-card"; + + label = "sound-card"; + + routing = "pcm3168a Playback", "DAI2 Playback", + "pcm3168a Playback", "DAI3 Playback", + "pcm3168a Playback", "DAI4 Playback", + "pcm3168a Playback", "DAI5 Playback"; + + dais = <&snd_port0 /* ak4613 */ + &snd_port1 /* HDMI0 */ + &snd_port2 /* pcm3168a playback */ + &snd_port3 /* pcm3168a capture */ + >; + }; + + ak4613: codec@10 { + ... + port { + ak4613_endpoint: endpoint { + remote-endpoint = <&rsnd_endpoint0>; + }; + }; + }; + + pcm3168a: audio-codec@44 { + ... + audio-graph-card,prefix = "pcm3168a"; + audio-graph-card,convert-channels = <8>; /* TDM Split */ + ports { + port@0 { + reg = <0>; + pcm3168a_endpoint_p1: endpoint@1 { + remote-endpoint = <&rsnd_endpoint2>; + ... + }; + pcm3168a_endpoint_p2: endpoint@2 { + remote-endpoint = <&rsnd_endpoint3>; + ... + }; + pcm3168a_endpoint_p3: endpoint@3 { + remote-endpoint = <&rsnd_endpoint4>; + ... + }; + pcm3168a_endpoint_p4: endpoint@4 { + remote-endpoint = <&rsnd_endpoint5>; + ... + }; + }; + port@1 { + reg = <1>; + pcm3168a_endpoint_c: endpoint { + remote-endpoint = <&rsnd_endpoint6>; + ... + }; + }; + }; + }; + + &sound { + ports { + snd_port0: port@0 { + rsnd_endpoint0: endpoint { + remote-endpoint = <&ak4613_endpoint>; + ... + }; + }; + snd_port1: port@1 { + rsnd_endpoint1: endpoint { + remote-endpoint = <&dw_hdmi0_snd_in>; + ... + }; + }; + snd_port2: port@2 { + #address-cells = <1>; + #size-cells = <0>; + rsnd_endpoint2: endpoint@2 { + remote-endpoint = <&pcm3168a_endpoint_p1>; + ... + }; + rsnd_endpoint3: endpoint@3 { + remote-endpoint = <&pcm3168a_endpoint_p2>; + ... + }; + rsnd_endpoint4: endpoint@4 { + remote-endpoint = <&pcm3168a_endpoint_p3>; + ... + }; + rsnd_endpoint5: endpoint@5 { + remote-endpoint = <&pcm3168a_endpoint_p4>; + ... + }; + }; + snd_port3: port@6 { + rsnd_endpoint6: endpoint { + remote-endpoint = <&pcm3168a_endpoint_c>; + ... + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/sound/audio-graph-scu-card.txt b/Documentation/devicetree/bindings/sound/audio-graph-scu-card.txt index 441dd6f29df1..62d42768a00b 100644 --- a/Documentation/devicetree/bindings/sound/audio-graph-scu-card.txt +++ b/Documentation/devicetree/bindings/sound/audio-graph-scu-card.txt @@ -77,11 +77,9 @@ Example 2. 2 CPU 1 Codec (Mixing) compatible = "audio-graph-scu-card"; label = "sound-card"; - prefix = "codec"; routing = "codec Playback", "DAI0 Playback", "codec Playback", "DAI1 Playback", "DAI0 Capture", "codec Capture"; - convert-rate = <48000>; dais = <&cpu_port0 &cpu_port1>; @@ -90,6 +88,8 @@ Example 2. 2 CPU 1 Codec (Mixing) audio-codec { ... + audio-graph-card,prefix = "codec"; + audio-graph-card,convert-rate = <48000>; port { codec_endpoint0: endpoint { remote-endpoint = <&cpu_endpoint0>; diff --git a/Documentation/devicetree/bindings/sound/cs4270.txt b/Documentation/devicetree/bindings/sound/cs4270.txt index 6b222f9b8ef5..c33770ec4c3c 100644 --- a/Documentation/devicetree/bindings/sound/cs4270.txt +++ b/Documentation/devicetree/bindings/sound/cs4270.txt @@ -10,8 +10,8 @@ Required properties: Optional properties: - - reset-gpio : a GPIO spec for the reset pin. If specified, it will be - deasserted before communication to the codec starts. + - reset-gpios : a GPIO spec for the reset pin. If specified, it will be + deasserted before communication to the codec starts. Example: diff --git a/Documentation/devicetree/bindings/sound/cs42l51.txt b/Documentation/devicetree/bindings/sound/cs42l51.txt new file mode 100644 index 000000000000..4b5de33ce377 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/cs42l51.txt @@ -0,0 +1,17 @@ +CS42L51 audio CODEC + +Optional properties: + + - clocks : a list of phandles + clock-specifiers, one for each entry in + clock-names + + - clock-names : must contain "MCLK" + +Example: + +cs42l51: cs42l51@4a { + compatible = "cirrus,cs42l51"; + reg = <0x4a>; + clocks = <&mclk_prov>; + clock-names = "MCLK"; +}; diff --git a/Documentation/devicetree/bindings/sound/davinci-mcasp-audio.txt b/Documentation/devicetree/bindings/sound/davinci-mcasp-audio.txt index 46bc9829c71a..b279b6072bd5 100644 --- a/Documentation/devicetree/bindings/sound/davinci-mcasp-audio.txt +++ b/Documentation/devicetree/bindings/sound/davinci-mcasp-audio.txt @@ -30,6 +30,11 @@ Optional properties: - ti,hwmods : Must be "mcasp<n>", n is controller instance starting 0 - tx-num-evt : FIFO levels. - rx-num-evt : FIFO levels. +- dismod : Specify the drive on TX pin during inactive slots + 0 : 3-state + 2 : logic low + 3 : logic high + Defaults to 'logic low' when the property is not present - sram-size-playback : size of sram to be allocated during playback - sram-size-capture : size of sram to be allocated during capture - interrupts : Interrupt numbers for McASP diff --git a/Documentation/devicetree/bindings/sound/dmic.txt b/Documentation/devicetree/bindings/sound/dmic.txt index e957b4136716..32e871037269 100644 --- a/Documentation/devicetree/bindings/sound/dmic.txt +++ b/Documentation/devicetree/bindings/sound/dmic.txt @@ -9,6 +9,7 @@ Optional properties: - dmicen-gpios: GPIO specifier for dmic to control start and stop - num-channels: Number of microphones on this DAI - wakeup-delay-ms: Delay (in ms) after enabling the DMIC + - modeswitch-delay-ms: Delay (in ms) to complete DMIC mode switch Example node: @@ -17,4 +18,5 @@ Example node: dmicen-gpios = <&gpio4 3 GPIO_ACTIVE_HIGH>; num-channels = <1>; wakeup-delay-ms <50>; + modeswitch-delay-ms <35>; }; diff --git a/Documentation/devicetree/bindings/sound/fsl-sai.txt b/Documentation/devicetree/bindings/sound/fsl-sai.txt index dd9e59738e08..2e726b983845 100644 --- a/Documentation/devicetree/bindings/sound/fsl-sai.txt +++ b/Documentation/devicetree/bindings/sound/fsl-sai.txt @@ -35,13 +35,13 @@ Required properties: - fsl,sai-synchronous-rx: This is a boolean property. If present, indicating that SAI will work in the synchronous mode (sync Tx - with Rx) which means both the transimitter and the + with Rx) which means both the transmitter and the receiver will send and receive data by following receiver's bit clocks and frame sync clocks. - fsl,sai-asynchronous: This is a boolean property. If present, indicating that SAI will work in the asynchronous mode, which - means both transimitter and receiver will send and + means both transmitter and receiver will send and receive data by following their own bit clocks and frame sync clocks separately. @@ -58,8 +58,8 @@ Optional properties (for mx6ul): Note: - If both fsl,sai-asynchronous and fsl,sai-synchronous-rx are absent, the default synchronous mode (sync Rx with Tx) will be used, which means both - transimitter and receiver will send and receive data by following clocks - of transimitter. + transmitter and receiver will send and receive data by following clocks + of transmitter. - fsl,sai-asynchronous and fsl,sai-synchronous-rx are exclusive. Example: diff --git a/Documentation/devicetree/bindings/sound/maxim,max98088.txt b/Documentation/devicetree/bindings/sound/maxim,max98088.txt new file mode 100644 index 000000000000..da764d913319 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/maxim,max98088.txt @@ -0,0 +1,23 @@ +MAX98088 audio CODEC + +This device supports I2C only. + +Required properties: + +- compatible: "maxim,max98088" or "maxim,max98089". +- reg: The I2C address of the device. + +Optional properties: + +- clocks: the clock provider of MCLK, see ../clock/clock-bindings.txt section + "consumer" for more information. +- clock-names: must be set to "mclk" + +Example: + +max98089: codec@10 { + compatible = "maxim,max98089"; + reg = <0x10>; + clocks = <&clks IMX6QDL_CLK_CKO2>; + clock-names = "mclk"; +}; diff --git a/Documentation/devicetree/bindings/sound/mikroe,mikroe-proto.txt b/Documentation/devicetree/bindings/sound/mikroe,mikroe-proto.txt new file mode 100644 index 000000000000..912f8fae11c5 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/mikroe,mikroe-proto.txt @@ -0,0 +1,23 @@ +Mikroe-PROTO audio board + +Required properties: + - compatible: "mikroe,mikroe-proto" + - dai-format: Must be "i2s". + - i2s-controller: The phandle of the I2S controller. + - audio-codec: The phandle of the WM8731 audio codec. +Optional properties: + - model: The user-visible name of this sound complex. + - bitclock-master: Indicates dai-link bit clock master; for details see simple-card.txt (1). + - frame-master: Indicates dai-link frame master; for details see simple-card.txt (1). + +(1) : There must be the same master for both bit and frame clocks. + +Example: + sound { + compatible = "mikroe,mikroe-proto"; + model = "wm8731 @ sama5d2_xplained"; + i2s-controller = <&i2s0>; + audio-codec = <&wm8731>; + dai-format = "i2s"; + }; +}; diff --git a/Documentation/devicetree/bindings/sound/nau8822.txt b/Documentation/devicetree/bindings/sound/nau8822.txt new file mode 100644 index 000000000000..a471d162d4e5 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/nau8822.txt @@ -0,0 +1,16 @@ +NAU8822 audio CODEC + +This device supports I2C only. + +Required properties: + + - compatible : "nuvoton,nau8822" + + - reg : the I2C address of the device. + +Example: + +codec: nau8822@1a { + compatible = "nuvoton,nau8822"; + reg = <0x1a>; +}; diff --git a/Documentation/devicetree/bindings/sound/omap-mcpdm.txt b/Documentation/devicetree/bindings/sound/omap-mcpdm.txt index 5f4e68ca228c..ff98a0cb5b3f 100644 --- a/Documentation/devicetree/bindings/sound/omap-mcpdm.txt +++ b/Documentation/devicetree/bindings/sound/omap-mcpdm.txt @@ -7,6 +7,8 @@ Required properties: <L3 interconnect address, size>; - interrupts: Interrupt number for McPDM - ti,hwmods: Name of the hwmod associated to the McPDM +- clocks: phandle for the pdmclk provider, likely <&twl6040> +- clock-names: Must be "pdmclk" Example: @@ -18,3 +20,11 @@ mcpdm: mcpdm@40132000 { interrupt-parent = <&gic>; ti,hwmods = "mcpdm"; }; + +In board DTS file the pdmclk needs to be added: + +&mcpdm { + clocks = <&twl6040>; + clock-names = "pdmclk"; + status = "okay"; +}; diff --git a/Documentation/devicetree/bindings/sound/pcm3060.txt b/Documentation/devicetree/bindings/sound/pcm3060.txt new file mode 100644 index 000000000000..97de66932d44 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/pcm3060.txt @@ -0,0 +1,23 @@ +PCM3060 audio CODEC + +This driver supports both I2C and SPI. + +Required properties: + +- compatible: "ti,pcm3060" + +- reg : the I2C address of the device for I2C, the chip select + number for SPI. + +Optional properties: + +- ti,out-single-ended: "true" if output is single-ended; + "false" or not specified if output is differential. + +Examples: + + pcm3060: pcm3060@46 { + compatible = "ti,pcm3060"; + reg = <0x46>; + ti,out-single-ended = "true"; + }; diff --git a/Documentation/devicetree/bindings/sound/qcom,q6afe.txt b/Documentation/devicetree/bindings/sound/qcom,q6afe.txt index a8179409c194..d74888b9f1bb 100644 --- a/Documentation/devicetree/bindings/sound/qcom,q6afe.txt +++ b/Documentation/devicetree/bindings/sound/qcom,q6afe.txt @@ -49,7 +49,7 @@ configuration of each dai. Must contain the following properties. Usage: required for mi2s interface Value type: <prop-encoded-array> Definition: Must be list of serial data lines used by this dai. - should be one or more of the 1-4 sd lines. + should be one or more of the 0-3 sd lines. - qcom,tdm-sync-mode: Usage: required for tdm interface @@ -137,42 +137,42 @@ q6afe@4 { prim-mi2s-rx@16 { reg = <16>; - qcom,sd-lines = <1 3>; + qcom,sd-lines = <0 2>; }; prim-mi2s-tx@17 { reg = <17>; - qcom,sd-lines = <2>; + qcom,sd-lines = <1>; }; sec-mi2s-rx@18 { reg = <18>; - qcom,sd-lines = <1 4>; + qcom,sd-lines = <0 3>; }; sec-mi2s-tx@19 { reg = <19>; - qcom,sd-lines = <2>; + qcom,sd-lines = <1>; }; tert-mi2s-rx@20 { reg = <20>; - qcom,sd-lines = <2 4>; + qcom,sd-lines = <1 3>; }; tert-mi2s-tx@21 { reg = <21>; - qcom,sd-lines = <1>; + qcom,sd-lines = <0>; }; quat-mi2s-rx@22 { reg = <22>; - qcom,sd-lines = <1>; + qcom,sd-lines = <0>; }; quat-mi2s-tx@23 { reg = <23>; - qcom,sd-lines = <2>; + qcom,sd-lines = <1>; }; }; }; diff --git a/Documentation/devicetree/bindings/sound/qcom,q6asm.txt b/Documentation/devicetree/bindings/sound/qcom,q6asm.txt index f9c7bd8c1bc0..9f5378c51686 100644 --- a/Documentation/devicetree/bindings/sound/qcom,q6asm.txt +++ b/Documentation/devicetree/bindings/sound/qcom,q6asm.txt @@ -27,6 +27,28 @@ used by the apr service device. Value type: <u32> Definition: Must be 1 +== ASM DAI is subnode of "dais" and represent a dai, it includes board specific +configuration of each dai. Must contain the following properties. + +- reg + Usage: required + Value type: <u32> + Definition: Must be dai id + +- direction: + Usage: Required for Compress offload dais + Value type: <u32> + Definition: Specifies the direction of the dai stream + 0 for both tx and rx + 1 for only tx (Capture/Encode) + 2 for only rx (Playback/Decode) + +- is-compress-dai: + Usage: Required for Compress offload dais + Value type: <boolean> + Definition: present for Compress offload dais + + = EXAMPLE q6asm@7 { @@ -35,5 +57,10 @@ q6asm@7 { q6asmdai: dais { compatible = "qcom,q6asm-dais"; #sound-dai-cells = <1>; + mm@0 { + reg = <0>; + direction = <2>; + is-compress-dai; + }; }; }; diff --git a/Documentation/devicetree/bindings/sound/renesas,rsnd.txt b/Documentation/devicetree/bindings/sound/renesas,rsnd.txt index 9e764270c36b..648d43e1b1e9 100644 --- a/Documentation/devicetree/bindings/sound/renesas,rsnd.txt +++ b/Documentation/devicetree/bindings/sound/renesas,rsnd.txt @@ -39,15 +39,7 @@ This is example of Playback: [MEM] -> [SRC2] -> [DVC0] -> [SSIU0/SSI0] -> [codec] Capture: [MEM] <- [DVC1] <- [SRC3] <- [SSIU1/SSI1] <- [codec] - &rcar_sound { - ... - rcar_sound,dai { - dai0 { - playback = <&ssi0 &src2 &dvc0>; - capture = <&ssi1 &src3 &dvc1>; - }; - }; - }; +see "Example: simple sound card" You can use below. ${LINUX}/arch/arm/boot/dts/r8a7790.dts can be good example. @@ -83,29 +75,8 @@ SRC can convert [xx]Hz to [yy]Hz. Then, it has below 2 modes ** Asynchronous mode ------------------ -You need to use "simple-scu-audio-card" sound card for it. -example) - - sound { - compatible = "simple-scu-audio-card"; - ... - /* - * SRC Asynchronous mode setting - * Playback: - * All input data will be converted to 48kHz - * Capture: - * Inputed 48kHz data will be converted to - * system specified Hz - */ - simple-audio-card,convert-rate = <48000>; - ... - simple-audio-card,cpu { - sound-dai = <&rcar_sound>; - }; - simple-audio-card,codec { - ... - }; - }; +You need to use "simple-scu-audio-card" or "audio-graph-scu-card" for it. +see "Example: simple sound card for Asynchronous mode" ------------------ ** Synchronous mode @@ -141,26 +112,8 @@ For more detail information, see below ${LINUX}/sound/soc/sh/rcar/ctu.c - comment of header -You need to use "simple-scu-audio-card" sound card for it. -example) - - sound { - compatible = "simple-scu-audio-card"; - ... - /* - * CTU setting - * All input data will be converted to 2ch - * as output data - */ - simple-audio-card,convert-channels = <2>; - ... - simple-audio-card,cpu { - sound-dai = <&rcar_sound>; - }; - simple-audio-card,codec { - ... - }; - }; +You need to use "simple-scu-audio-card" or "audio-graph-scu-card" for it. +see "Example: simple sound card for channel convert" Ex) Exchange output channel Input -> Output @@ -190,42 +143,13 @@ and these sounds will be merged by MIX. aplay -D plughw:0,0 xxxx.wav & aplay -D plughw:0,1 yyyy.wav -You need to use "simple-scu-audio-card" sound card for it. +You need to use "simple-scu-audio-card" or "audio-graph-scu-card" for it. Ex) [MEM] -> [SRC1] -> [CTU02] -+-> [MIX0] -> [DVC0] -> [SSI0] | [MEM] -> [SRC2] -> [CTU03] -+ - sound { - #address-cells = <1>; - #size-cells = <0>; - - compatible = "simple-scu-audio-card"; - ... - simple-audio-card,cpu@0 { - reg = <0>; - sound-dai = <&rcar_sound 0>; - }; - simple-audio-card,cpu@1 { - reg = <1>; - sound-dai = <&rcar_sound 1>; - }; - simple-audio-card,codec { - ... - }; - }; - - &rcar_sound { - ... - rcar_sound,dai { - dai0 { - playback = <&src1 &ctu02 &mix0 &dvc0 &ssi0>; - }; - dai1 { - playback = <&src2 &ctu03 &mix0 &dvc0 &ssi0>; - }; - }; - }; +see "Example: simple sound card for MIXer" ============================================= * DVC (Digital Volume and Mute Function) @@ -257,15 +181,31 @@ Volume Ramp * SSIU (Serial Sound Interface Unit) ============================================= -There is no DT settings for SSIU, because SSIU will be automatically -selected via SSI. SSIU can avoid some under/over run error, because it has some buffer. But you can't use it if SSI was PIO mode. -In DMA mode, you can select not to use SSIU by using "no-busif" on DT. +In DMA mode, you can select not to use SSIU by using "no-busif" via SSI. - &ssi0 { - no-busif; - }; +SSIU handles BUSIF which will be used for TDM Split mode. +This driver is assuming that audio-graph card will be used. + +TDM Split mode merges 4 sounds. You can see 4 sound interface on system, +and these sounds will be merged SSIU/SSI. + + aplay -D plughw:0,0 xxxx.wav & + aplay -D plughw:0,1 xxxx.wav & + aplay -D plughw:0,2 xxxx.wav & + aplay -D plughw:0,3 xxxx.wav + + 2ch 8ch + [MEM] -> [SSIU 30] -+-> [SSIU 3] --> [Codec] + 2ch | + [MEM] -> [SSIU 31] -+ + 2ch | + [MEM] -> [SSIU 32] -+ + 2ch | + [MEM] -> [SSIU 33] -+ + +see "Example: simple sound card for TDM Split" ============================================= * SSI (Serial Sound Interface) @@ -304,14 +244,7 @@ This is example if SSI1 want to share WS pin with SSI0 You can use Multi-SSI. This is example of SSI0/SSI1/SSI2 (= for 6ch) - &rcar_sound { - ... - rcar_sound,dai { - dai0 { - playback = <&ssi0 &ssi1 &ssi2 &src0 &dvc0>; - }; - }; - }; +see "Example: simple sound card for Multi channel" ** TDM-SSI @@ -319,19 +252,7 @@ You can use TDM with SSI. This is example of TDM 6ch. Driver can automatically switches TDM <-> stereo mode in this case. - rsnd_tdm: sound { - compatible = "simple-audio-card"; - ... - simple-audio-card,cpu { - /* system can use TDM 6ch */ - dai-tdm-slot-num = <6>; - sound-dai = <&rcar_sound>; - }; - simple-audio-card,codec { - ... - }; - }; - +see "Example: simple sound card for TDM" ============================================= Required properties: @@ -340,10 +261,13 @@ Required properties: - compatible : "renesas,rcar_sound-<soctype>", fallbacks "renesas,rcar_sound-gen1" if generation1, and "renesas,rcar_sound-gen2" if generation2 (or RZ/G1) - "renesas,rcar_sound-gen3" if generation3 + "renesas,rcar_sound-gen3" if generation3 (or RZ/G2) Examples with soctypes are: - "renesas,rcar_sound-r8a7743" (RZ/G1M) + - "renesas,rcar_sound-r8a7744" (RZ/G1N) - "renesas,rcar_sound-r8a7745" (RZ/G1E) + - "renesas,rcar_sound-r8a774a1" (RZ/G2M) + - "renesas,rcar_sound-r8a774c0" (RZ/G2E) - "renesas,rcar_sound-r8a7778" (R-Car M1A) - "renesas,rcar_sound-r8a7779" (R-Car H1) - "renesas,rcar_sound-r8a7790" (R-Car H2) @@ -353,6 +277,8 @@ Required properties: - "renesas,rcar_sound-r8a7795" (R-Car H3) - "renesas,rcar_sound-r8a7796" (R-Car M3-W) - "renesas,rcar_sound-r8a77965" (R-Car M3-N) + - "renesas,rcar_sound-r8a77990" (R-Car E3) + - "renesas,rcar_sound-r8a77995" (R-Car D3) - reg : Should contain the register physical address. required register is SRU/ADG/SSI if generation1 @@ -360,6 +286,9 @@ Required properties: - rcar_sound,ssi : Should contain SSI feature. The number of SSI subnode should be same as HW. see below for detail. +- rcar_sound,ssiu : Should contain SSIU feature. + The number of SSIU subnode should be same as HW. + see below for detail. - rcar_sound,src : Should contain SRC feature. The number of SRC subnode should be same as HW. see below for detail. @@ -399,8 +328,13 @@ SSI subnode properties: - no-busif : BUSIF is not ussed when [mem -> SSI] via DMA case - dma : Should contain Audio DMAC entry - dma-names : SSI case "rx" (=playback), "tx" (=capture) + Deprecated: see SSIU subnode properties SSIU case "rxu" (=playback), "txu" (=capture) +SSIU subnode properties: +- dma : Should contain Audio DMAC entry +- dma-names : "rx" (=playback), "tx" (=capture) + SRC subnode properties: - dma : Should contain Audio DMAC entry - dma-names : "rx" (=playback), "tx" (=capture) @@ -529,56 +463,55 @@ rcar_sound: sound@ec500000 { }; }; + rcar_sound,ssiu { + ssiu00: ssiu-0 { + dmas = <&audma0 0x15>, <&audma1 0x16>; + dma-names = "rx", "tx"; + }; + ssiu01: ssiu-1 { + dmas = <&audma0 0x35>, <&audma1 0x36>; + dma-names = "rx", "tx"; + }; + + ... + + ssiu95: ssiu-49 { + dmas = <&audma0 0xA5>, <&audma1 0xA6>; + dma-names = "rx", "tx"; + }; + ssiu96: ssiu-50 { + dmas = <&audma0 0xA7>, <&audma1 0xA8>; + dma-names = "rx", "tx"; + }; + ssiu97: ssiu-51 { + dmas = <&audma0 0xA9>, <&audma1 0xAA>; + dma-names = "rx", "tx"; + }; + }; + rcar_sound,ssi { ssi0: ssi-0 { interrupts = <0 370 IRQ_TYPE_LEVEL_HIGH>; - dmas = <&audma0 0x01>, <&audma1 0x02>, <&audma0 0x15>, <&audma1 0x16>; - dma-names = "rx", "tx", "rxu", "txu"; + dmas = <&audma0 0x01>, <&audma1 0x02>; + dma-names = "rx", "tx"; }; ssi1: ssi-1 { interrupts = <0 371 IRQ_TYPE_LEVEL_HIGH>; - dmas = <&audma0 0x03>, <&audma1 0x04>, <&audma0 0x49>, <&audma1 0x4a>; - dma-names = "rx", "tx", "rxu", "txu"; - }; - ssi2: ssi-2 { - interrupts = <0 372 IRQ_TYPE_LEVEL_HIGH>; - dmas = <&audma0 0x05>, <&audma1 0x06>, <&audma0 0x63>, <&audma1 0x64>; - dma-names = "rx", "tx", "rxu", "txu"; - }; - ssi3: ssi-3 { - interrupts = <0 373 IRQ_TYPE_LEVEL_HIGH>; - dmas = <&audma0 0x07>, <&audma1 0x08>, <&audma0 0x6f>, <&audma1 0x70>; - dma-names = "rx", "tx", "rxu", "txu"; - }; - ssi4: ssi-4 { - interrupts = <0 374 IRQ_TYPE_LEVEL_HIGH>; - dmas = <&audma0 0x09>, <&audma1 0x0a>, <&audma0 0x71>, <&audma1 0x72>; - dma-names = "rx", "tx", "rxu", "txu"; - }; - ssi5: ssi-5 { - interrupts = <0 375 IRQ_TYPE_LEVEL_HIGH>; - dmas = <&audma0 0x0b>, <&audma1 0x0c>, <&audma0 0x73>, <&audma1 0x74>; - dma-names = "rx", "tx", "rxu", "txu"; - }; - ssi6: ssi-6 { - interrupts = <0 376 IRQ_TYPE_LEVEL_HIGH>; - dmas = <&audma0 0x0d>, <&audma1 0x0e>, <&audma0 0x75>, <&audma1 0x76>; - dma-names = "rx", "tx", "rxu", "txu"; - }; - ssi7: ssi-7 { - interrupts = <0 377 IRQ_TYPE_LEVEL_HIGH>; - dmas = <&audma0 0x0f>, <&audma1 0x10>, <&audma0 0x79>, <&audma1 0x7a>; - dma-names = "rx", "tx", "rxu", "txu"; + dmas = <&audma0 0x03>, <&audma1 0x04>; + dma-names = "rx", "tx"; }; + + ... + ssi8: ssi-8 { interrupts = <0 378 IRQ_TYPE_LEVEL_HIGH>; - dmas = <&audma0 0x11>, <&audma1 0x12>, <&audma0 0x7b>, <&audma1 0x7c>; - dma-names = "rx", "tx", "rxu", "txu"; + dmas = <&audma0 0x11>, <&audma1 0x12>; + dma-names = "rx", "tx"; }; ssi9: ssi-9 { interrupts = <0 379 IRQ_TYPE_LEVEL_HIGH>; - dmas = <&audma0 0x13>, <&audma1 0x14>, <&audma0 0x7d>, <&audma1 0x7e>; - dma-names = "rx", "tx", "rxu", "txu"; + dmas = <&audma0 0x13>, <&audma1 0x14>; + dma-names = "rx", "tx"; }; }; @@ -644,25 +577,174 @@ Example: simple sound card }; ============================================= +Example: simple sound card for Asynchronous mode +============================================= + +sound { + compatible = "simple-scu-audio-card"; + ... + /* + * SRC Asynchronous mode setting + * Playback: + * All input data will be converted to 48kHz + * Capture: + * Inputed 48kHz data will be converted to + * system specified Hz + */ + simple-audio-card,convert-rate = <48000>; + ... + simple-audio-card,cpu { + sound-dai = <&rcar_sound>; + }; + simple-audio-card,codec { + ... + }; +}; + +============================================= +Example: simple sound card for channel convert +============================================= + +sound { + compatible = "simple-scu-audio-card"; + ... + /* + * CTU setting + * All input data will be converted to 2ch + * as output data + */ + simple-audio-card,convert-channels = <2>; + ... + simple-audio-card,cpu { + sound-dai = <&rcar_sound>; + }; + simple-audio-card,codec { + ... + }; +}; + +============================================= +Example: simple sound card for MIXer +============================================= + +sound { + compatible = "simple-scu-audio-card"; + ... + simple-audio-card,cpu@0 { + sound-dai = <&rcar_sound 0>; + }; + simple-audio-card,cpu@1 { + sound-dai = <&rcar_sound 1>; + }; + simple-audio-card,codec { + ... + }; +}; + +&rcar_sound { + ... + rcar_sound,dai { + dai0 { + playback = <&src1 &ctu02 &mix0 &dvc0 &ssi0>; + }; + dai1 { + playback = <&src2 &ctu03 &mix0 &dvc0 &ssi0>; + }; + }; +}; + +============================================= Example: simple sound card for TDM ============================================= - rsnd_tdm: sound { - compatible = "simple-audio-card"; +rsnd_tdm: sound { + compatible = "simple-audio-card"; - simple-audio-card,format = "left_j"; - simple-audio-card,bitclock-master = <&sndcodec>; - simple-audio-card,frame-master = <&sndcodec>; + simple-audio-card,format = "left_j"; + simple-audio-card,bitclock-master = <&sndcodec>; + simple-audio-card,frame-master = <&sndcodec>; - sndcpu: simple-audio-card,cpu { - sound-dai = <&rcar_sound>; - dai-tdm-slot-num = <6>; + sndcpu: simple-audio-card,cpu { + sound-dai = <&rcar_sound>; + dai-tdm-slot-num = <6>; + }; + + sndcodec: simple-audio-card,codec { + sound-dai = <&xxx>; + }; +}; + +============================================= +Example: simple sound card for TDM Split +============================================= + +sound_card: sound { + compatible = "audio-graph-scu-card"; + prefix = "xxxx"; + routing = "xxxx Playback", "DAI0 Playback", + "xxxx Playback", "DAI1 Playback", + "xxxx Playback", "DAI2 Playback", + "xxxx Playback", "DAI3 Playback"; + convert-channels = <8>; /* TDM Split */ + + dais = <&rsnd_port0 /* playback ch1/ch2 */ + &rsnd_port1 /* playback ch3/ch4 */ + &rsnd_port2 /* playback ch5/ch6 */ + &rsnd_port3 /* playback ch7/ch8 */ + >; +}; + +audio-codec { + ... + port { + codec_0: endpoint@1 { + remote-endpoint = <&rsnd_ep0>; + }; + codec_1: endpoint@2 { + remote-endpoint = <&rsnd_ep1>; + }; + codec_2: endpoint@3 { + remote-endpoint = <&rsnd_ep2>; + }; + codec_3: endpoint@4 { + remote-endpoint = <&rsnd_ep3>; }; + }; +}; - sndcodec: simple-audio-card,codec { - sound-dai = <&xxx>; +&rcar_sound { + ... + ports { + rsnd_port0: port@0 { + rsnd_ep0: endpoint { + remote-endpoint = <&codec_0>; + ... + playback = <&ssiu30 &ssi3>; + }; + }; + rsnd_port1: port@1 { + rsnd_ep1: endpoint { + remote-endpoint = <&codec_1>; + ... + playback = <&ssiu31 &ssi3>; + }; + }; + rsnd_port2: port@2 { + rsnd_ep2: endpoint { + remote-endpoint = <&codec_2>; + ... + playback = <&ssiu32 &ssi3>; + }; + }; + rsnd_port3: port@3 { + rsnd_ep3: endpoint { + remote-endpoint = <&codec_3>; + ... + playback = <&ssiu33 &ssi3>; + }; }; }; +}; ============================================= Example: simple sound card for Multi channel diff --git a/Documentation/devicetree/bindings/sound/rt5631.txt b/Documentation/devicetree/bindings/sound/rt5631.txt index 92b986ca337b..56bc85232c49 100644 --- a/Documentation/devicetree/bindings/sound/rt5631.txt +++ b/Documentation/devicetree/bindings/sound/rt5631.txt @@ -35,14 +35,14 @@ Pins on the device (for linking into audio routes): Example: -alc5631: alc5631@1a { +alc5631: audio-codec@1a { compatible = "realtek,alc5631"; reg = <0x1a>; }; or -rt5631: rt5631@1a { +rt5631: audio-codec@1a { compatible = "realtek,rt5631"; reg = <0x1a>; }; diff --git a/Documentation/devicetree/bindings/sound/rt5663.txt b/Documentation/devicetree/bindings/sound/rt5663.txt index 23386446c63d..2a55e9133408 100644 --- a/Documentation/devicetree/bindings/sound/rt5663.txt +++ b/Documentation/devicetree/bindings/sound/rt5663.txt @@ -10,6 +10,10 @@ Required properties: - interrupts : The CODEC's interrupt output. +- avdd-supply: Power supply for AVDD, providing 1.8V. + +- cpvdd-supply: Power supply for CPVDD, providing 3.5V. + Optional properties: - "realtek,dc_offset_l_manual" @@ -51,4 +55,6 @@ rt5663: codec@12 { compatible = "realtek,rt5663"; reg = <0x12>; interrupts = <7 IRQ_TYPE_EDGE_FALLING>; + avdd-supply = <&pp1800_a_alc5662>; + cpvdd-supply = <&pp3500_a_alc5662>; }; diff --git a/Documentation/devicetree/bindings/sound/simple-amplifier.txt b/Documentation/devicetree/bindings/sound/simple-amplifier.txt index 8647edae7af0..7182ac4f1e65 100644 --- a/Documentation/devicetree/bindings/sound/simple-amplifier.txt +++ b/Documentation/devicetree/bindings/sound/simple-amplifier.txt @@ -4,9 +4,14 @@ Required properties: - compatible : "dioo,dio2125" or "simple-audio-amplifier" - enable-gpios : the gpio connected to the enable pin of the simple amplifier +Optional properties: +- VCC-supply : power supply for the device, as covered + in Documentation/devicetree/bindings/regulator/regulator.txt + Example: amp: analog-amplifier { compatible = "simple-audio-amplifier"; + VCC-supply = <®ulator>; enable-gpios = <&gpio GPIOH_3 0>; }; diff --git a/Documentation/devicetree/bindings/sound/simple-card.txt b/Documentation/devicetree/bindings/sound/simple-card.txt index a4c72d09cd45..4629c8f8a6b6 100644 --- a/Documentation/devicetree/bindings/sound/simple-card.txt +++ b/Documentation/devicetree/bindings/sound/simple-card.txt @@ -95,7 +95,9 @@ Optional CPU/CODEC subnodes properties: initialization. It is useful for some aCPUs with fixed clocks. +------------------------------------------- Example 1 - single DAI link: +------------------------------------------- sound { compatible = "simple-audio-card"; @@ -138,7 +140,9 @@ sh_fsi2: sh_fsi2@ec230000 { interrupts = <0 146 0x4>; }; +------------------------------------------- Example 2 - many DAI links: +------------------------------------------- sound { compatible = "simple-audio-card"; @@ -176,8 +180,10 @@ sound { }; }; +------------------------------------------- Example 3 - route audio from IMX6 SSI2 through TLV320DAC3100 codec through TPA6130A2 amplifier to headphones: +------------------------------------------- &i2c0 { codec: tlv320dac3100@18 { @@ -210,3 +216,134 @@ sound { clocks = ... }; }; + +------------------------------------------- +Example 4. Sampling Rate Conversion +------------------------------------------- + +sound { + compatible = "simple-audio-card"; + + simple-audio-card,name = "rsnd-ak4643"; + simple-audio-card,format = "left_j"; + simple-audio-card,bitclock-master = <&sndcodec>; + simple-audio-card,frame-master = <&sndcodec>; + + simple-audio-card,convert-rate = <48000>; + + simple-audio-card,prefix = "ak4642"; + simple-audio-card,routing = "ak4642 Playback", "DAI0 Playback", + "DAI0 Capture", "ak4642 Capture"; + + sndcpu: simple-audio-card,cpu { + sound-dai = <&rcar_sound>; + }; + + sndcodec: simple-audio-card,codec { + sound-dai = <&ak4643>; + system-clock-frequency = <11289600>; + }; +}; + +------------------------------------------- +Example 5. 2 CPU 1 Codec (Mixing) +------------------------------------------- +sound { + compatible = "simple-audio-card"; + + simple-audio-card,name = "rsnd-ak4643"; + simple-audio-card,format = "left_j"; + simple-audio-card,bitclock-master = <&dpcmcpu>; + simple-audio-card,frame-master = <&dpcmcpu>; + + simple-audio-card,routing = "ak4642 Playback", "DAI0 Playback", + "ak4642 Playback", "DAI1 Playback"; + + dpcmcpu: cpu@0 { + sound-dai = <&rcar_sound 0>; + }; + + cpu@1 { + sound-dai = <&rcar_sound 1>; + }; + + codec { + prefix = "ak4642"; + sound-dai = <&ak4643>; + clocks = <&audio_clock>; + }; +}; + +------------------------------------------- +Example 6 - many DAI links with DPCM: +------------------------------------------- + +CPU0 ------ ak4613 +CPU1 ------ PCM3168A-p /* DPCM 1ch/2ch */ +CPU2 --/ /* DPCM 3ch/4ch */ +CPU3 --/ /* DPCM 5ch/6ch */ +CPU4 --/ /* DPCM 7ch/8ch */ +CPU5 ------ PCM3168A-c + +sound { + compatible = "simple-audio-card"; + + simple-audio-card,routing = + "pcm3168a Playback", "DAI1 Playback", + "pcm3168a Playback", "DAI2 Playback", + "pcm3168a Playback", "DAI3 Playback", + "pcm3168a Playback", "DAI4 Playback"; + + simple-audio-card,dai-link@0 { + format = "left_j"; + bitclock-master = <&sndcpu0>; + frame-master = <&sndcpu0>; + + sndcpu0: cpu { + sound-dai = <&rcar_sound 0>; + }; + codec { + sound-dai = <&ak4613>; + }; + }; + simple-audio-card,dai-link@1 { + format = "i2s"; + bitclock-master = <&sndcpu1>; + frame-master = <&sndcpu1>; + + convert-channels = <8>; /* TDM Split */ + + sndcpu1: cpu@0 { + sound-dai = <&rcar_sound 1>; + }; + cpu@1 { + sound-dai = <&rcar_sound 2>; + }; + cpu@2 { + sound-dai = <&rcar_sound 3>; + }; + cpu@3 { + sound-dai = <&rcar_sound 4>; + }; + codec { + mclk-fs = <512>; + prefix = "pcm3168a"; + dai-tdm-slot-num = <8>; + sound-dai = <&pcm3168a 0>; + }; + }; + simple-audio-card,dai-link@2 { + format = "i2s"; + bitclock-master = <&sndcpu2>; + frame-master = <&sndcpu2>; + + sndcpu2: cpu { + sound-dai = <&rcar_sound 5>; + }; + codec { + mclk-fs = <512>; + prefix = "pcm3168a"; + sound-dai = <&pcm3168a 1>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/sound/simple-scu-card.txt b/Documentation/devicetree/bindings/sound/simple-scu-card.txt index 32f8dbce5241..3a2f71616cda 100644 --- a/Documentation/devicetree/bindings/sound/simple-scu-card.txt +++ b/Documentation/devicetree/bindings/sound/simple-scu-card.txt @@ -75,7 +75,6 @@ sound { simple-audio-card,bitclock-master = <&dpcmcpu>; simple-audio-card,frame-master = <&dpcmcpu>; - simple-audio-card,prefix = "ak4642"; simple-audio-card,routing = "ak4642 Playback", "DAI0 Playback", "ak4642 Playback", "DAI1 Playback"; @@ -88,6 +87,7 @@ sound { }; codec { + prefix = "ak4642"; sound-dai = <&ak4643>; clocks = <&audio_clock>; }; diff --git a/Documentation/devicetree/bindings/sound/st,sta32x.txt b/Documentation/devicetree/bindings/sound/st,sta32x.txt index 255de3ae5b2f..52265fb757c5 100644 --- a/Documentation/devicetree/bindings/sound/st,sta32x.txt +++ b/Documentation/devicetree/bindings/sound/st,sta32x.txt @@ -19,6 +19,10 @@ Required properties: Optional properties: + - clocks, clock-names: Clock specifier for XTI input clock. + If specified, the clock will be enabled when the codec is probed, + and disabled when it is removed. The 'clock-names' must be set to 'xti'. + - st,output-conf: number, Selects the output configuration: 0: 2-channel (full-bridge) power, 2-channel data-out 1: 2 (half-bridge). 1 (full-bridge) on-board power @@ -39,6 +43,9 @@ Optional properties: - st,thermal-warning-recover: If present, thermal warning recovery is enabled. + - st,fault-detect-recovery: + If present, fault detect recovery is enabled. + - st,thermal-warning-adjustment: If present, thermal warning adjustment is enabled. @@ -76,6 +83,8 @@ Example: codec: sta32x@38 { compatible = "st,sta32x"; reg = <0x1c>; + clocks = <&clock>; + clock-names = "xti"; reset-gpios = <&gpio1 19 0>; power-down-gpios = <&gpio1 16 0>; st,output-conf = /bits/ 8 <0x3>; // set output to 2-channel diff --git a/Documentation/devicetree/bindings/sound/st,stm32-sai.txt b/Documentation/devicetree/bindings/sound/st,stm32-sai.txt index 3a3fc506e43a..3f4467ff0aa2 100644 --- a/Documentation/devicetree/bindings/sound/st,stm32-sai.txt +++ b/Documentation/devicetree/bindings/sound/st,stm32-sai.txt @@ -31,7 +31,11 @@ SAI subnodes required properties: - reg: Base address and size of SAI sub-block register set. - clocks: Must contain one phandle and clock specifier pair for sai_ck which feeds the internal clock generator. + If the SAI shares a master clock, with another SAI set as MCLK + clock provider, SAI provider phandle must be specified here. - clock-names: Must contain "sai_ck". + Must also contain "MCLK", if SAI shares a master clock, + with a SAI set as MCLK clock provider. - dmas: see Documentation/devicetree/bindings/dma/stm32-dma.txt - dma-names: identifier string for each DMA request line "tx": if sai sub-block is configured as playback DAI @@ -51,6 +55,9 @@ SAI subnodes Optional properties: configured according to protocol defined in related DAI link node, such as i2s, left justified, right justified, dsp and pdm protocols. Note: ac97 protocol is not supported by SAI driver + - #clock-cells: should be 0. This property must be present if the SAI device + is a master clock provider, according to clocks bindings, described in + Documentation/devicetree/bindings/clock/clock-bindings.txt. The device node should contain one 'port' child node with one child 'endpoint' node, according to the bindings defined in Documentation/devicetree/bindings/ diff --git a/Documentation/devicetree/bindings/sound/sun4i-i2s.txt b/Documentation/devicetree/bindings/sound/sun4i-i2s.txt index b9d50d6cdef3..61e71c1729e0 100644 --- a/Documentation/devicetree/bindings/sound/sun4i-i2s.txt +++ b/Documentation/devicetree/bindings/sound/sun4i-i2s.txt @@ -10,6 +10,7 @@ Required properties: - "allwinner,sun6i-a31-i2s" - "allwinner,sun8i-a83t-i2s" - "allwinner,sun8i-h3-i2s" + - "allwinner,sun50i-a64-codec-i2s" - reg: physical base address of the controller and length of memory mapped region. - interrupts: should contain the I2S interrupt. @@ -26,6 +27,7 @@ Required properties for the following compatibles: - "allwinner,sun6i-a31-i2s" - "allwinner,sun8i-a83t-i2s" - "allwinner,sun8i-h3-i2s" + - "allwinner,sun50i-a64-codec-i2s" - resets: phandle to the reset line for this codec Example: diff --git a/Documentation/devicetree/bindings/sound/sun50i-codec-analog.txt b/Documentation/devicetree/bindings/sound/sun50i-codec-analog.txt new file mode 100644 index 000000000000..056a098495cc --- /dev/null +++ b/Documentation/devicetree/bindings/sound/sun50i-codec-analog.txt @@ -0,0 +1,14 @@ +* Allwinner A64 Codec Analog Controls + +Required properties: +- compatible: must be one of the following compatibles: + - "allwinner,sun50i-a64-codec-analog" +- reg: must contain the registers location and length +- cpvdd-supply: Regulator supply for the headphone amplifier + +Example: + codec_analog: codec-analog@1f015c0 { + compatible = "allwinner,sun50i-a64-codec-analog"; + reg = <0x01f015c0 0x4>; + cpvdd-supply = <®_eldo1>; + }; diff --git a/Documentation/devicetree/bindings/sound/ts3a227e.txt b/Documentation/devicetree/bindings/sound/ts3a227e.txt index 3ed8359144d3..21ab45bc7e8f 100644 --- a/Documentation/devicetree/bindings/sound/ts3a227e.txt +++ b/Documentation/devicetree/bindings/sound/ts3a227e.txt @@ -14,7 +14,7 @@ Required properties: Optional properies: - ti,micbias: Intended MICBIAS voltage (datasheet section 9.6.7). - Select 0/1/2/3/4/5/6/7 to specify MACBIAS voltage + Select 0/1/2/3/4/5/6/7 to specify MICBIAS voltage 2.1V/2.2V/2.3V/2.4V/2.5V/2.6V/2.7V/2.8V Default value is "1" (2.2V). diff --git a/Documentation/devicetree/bindings/sound/wm8782.txt b/Documentation/devicetree/bindings/sound/wm8782.txt new file mode 100644 index 000000000000..256cdec6ec4d --- /dev/null +++ b/Documentation/devicetree/bindings/sound/wm8782.txt @@ -0,0 +1,17 @@ +WM8782 stereo ADC + +This device does not have any control interface or reset pins. + +Required properties: + + - compatible : "wlf,wm8782" + - Vdda-supply : phandle to a regulator for the analog power supply (2.7V - 5.5V) + - Vdd-supply : phandle to a regulator for the digital power supply (2.7V - 3.6V) + +Example: + +wm8782: stereo-adc { + compatible = "wlf,wm8782"; + Vdda-supply = <&vdda_supply>; + Vdd-supply = <&vdd_supply>; +}; diff --git a/Documentation/devicetree/bindings/sound/xlnx,i2s.txt b/Documentation/devicetree/bindings/sound/xlnx,i2s.txt new file mode 100644 index 000000000000..5e7c7d5bb60a --- /dev/null +++ b/Documentation/devicetree/bindings/sound/xlnx,i2s.txt @@ -0,0 +1,28 @@ +Device-Tree bindings for Xilinx I2S PL block + +The IP supports I2S based playback/capture audio + +Required property: + - compatible: "xlnx,i2s-transmitter-1.0" for playback and + "xlnx,i2s-receiver-1.0" for capture + +Required property common to both I2S playback and capture: + - reg: Base address and size of the IP core instance. + - xlnx,dwidth: sample data width. Can be any of 16, 24. + - xlnx,num-channels: Number of I2S streams. Can be any of 1, 2, 3, 4. + supported channels = 2 * xlnx,num-channels + +Example: + + i2s_receiver@a0080000 { + compatible = "xlnx,i2s-receiver-1.0"; + reg = <0x0 0xa0080000 0x0 0x10000>; + xlnx,dwidth = <0x18>; + xlnx,num-channels = <1>; + }; + i2s_transmitter@a0090000 { + compatible = "xlnx,i2s-transmitter-1.0"; + reg = <0x0 0xa0090000 0x0 0x10000>; + xlnx,dwidth = <0x18>; + xlnx,num-channels = <1>; + }; |